TY - JOUR A1 - Martin, Sven A1 - Krüger, Jörg A1 - Hertwig, Andreas A1 - Fiedler, A. A1 - Kautek, Wolfgang T1 - Femtosecond laser interaction with protection materials N2 - Textile, aluminium and polyethylene used as components in laser protection curtains were investigated with respect to their ablation behaviour. Employing 33-fs pulses (800 nm wavelength, 1 kHz repetition rate), ex situ geometrical measurements of the ablation cavities and in situ acoustic investigations with a microphone were performed to determine the ablation thresholds in the single- and multi-pulse cases. The acoustical method proved advantageous for complex surface morphologies and/or single laser pulse interactions. Incubation phenomena can be observed for all the materials studied. Technically relevant multi-pulse ablation thresholds are presented and are compared with the single-pulse (1-on-1) irradiation. KW - Damage KW - Femtosecond laser ablation KW - Laser safety KW - Threshold KW - Aluminium KW - Textile PY - 2003 DO - https://doi.org/10.1016/S0169-4332(02)01392-2 SN - 0169-4332 SN - 1873-5584 VL - 208-209 SP - 333 EP - 339 PB - North-Holland CY - Amsterdam AN - OPUS4-11546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lenzner, Matthias A1 - Krüger, Jörg A1 - Sartania, S. A1 - Cheng, Z. A1 - Spielmann, Ch. A1 - Mourou, G. A1 - Kautek, Wolfgang A1 - Krausz, F. T1 - Femtosecond Optical Breakdown in Dielectrics N2 - We report measurements of the optical breakdown threshold and ablation depth in dielectrics with different band gaps for laser pulse durations ranging from 5 ps to 5 fs at a carrier wavelength of 780 nm. For tau <100 fs, the dominant channel for free electron generation is found to be either impact or multiphoton ionization (MPI) depending on the size of the band gap. The observed MPI rates are substantially lower than those predicted by the Keldysh theory. We demonstrate that sub-10-fs laser pulses open up the way to reversible nonperturbative nonlinear optics (at intensities greater than 1014 W/cm2 slightly below damage threshold) and to nanometer-precision laser ablation (slightly above threshold) in dielectric materials. PY - 1998 SN - 0031-9007 SN - 1079-7114 VL - 80 IS - 18 SP - 4076 EP - 4079 PB - American Physical Society CY - Ridge, NY AN - OPUS4-11518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - Femtosecond pulse visible laser processing of fibre composite materials N2 - A first investigation on the ablation of composite materials like carbon and silicon-carbide reinforced alumo- and borosilicate glasses by 300 fs laser pulses (620 nm) in comparison to experiments with 17 ns pulse excimer laser (308 nm) treatment is presented. In all composites, femtosecond laser scans with a fluence of less than 2 J cm-2 produce well defined cuts with smooth side walls in contrast to the nanosecond laser result where extremely incongruent ablation is observed. Visible lasers should not be applicable because SiC and the glasses are practically transparent. Visible subpicosecond pulses of high intensity in the TW cm-2 range allow multi-photon absorption accompanied by incubation phenomena. The morphology of the groove edges reveal the contrasting ablation thresholds and rates of the fibre and glass materials. The ablation thresholds of the transparent components, i.e. the glass matrices and SiC, are about one order of magnitude greater than that of carbon which is ~ 0.15 J cm-2. Incubation effects are important for the absorption mechanisms in the transparent materials. When a critical number of pulses has not been reached at the SiC-glass composites, only the glass is preferentially ablated, and the fibres remain intact. This is in contrast to the C-glass composites where the ablation behaviour is opposite. PY - 1996 SN - 0169-4332 SN - 1873-5584 VL - 106 SP - 383 EP - 389 PB - North-Holland CY - Amsterdam AN - OPUS4-11506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bunte, J. A1 - Barcikowski, S. A1 - Burmester, T. A1 - Püster, T. A1 - Hertwig, Andreas A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Martin, Sven A1 - Spielmann, C. A1 - Lenner, M. A1 - Brose, M. T1 - Sicherer Umgang mit Ultrakurzpuls-Lasern, Teil 1: Primäre Gefährdungen PY - 2005 SN - 0945-8875 IS - 2 SP - 6 EP - 11 PB - Magazin-Verl. CY - Bad Nenndorf AN - OPUS4-11001 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bunte, J. A1 - Barcikowski, S. A1 - Burmester, T. A1 - Püster, T. A1 - Hertwig, Andreas A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Martin, Sven A1 - Spielmann, C. A1 - Lenner, M. A1 - Brose, M. T1 - Sicherer Umgang mit Ultrakurzpuls-Lasern, Teil 2: Sekundäre Gefährdungen PY - 2005 SN - 0945-8875 IS - 4 SP - 13 EP - 18 PB - Magazin-Verl. CY - Bad Nenndorf AN - OPUS4-11002 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Mikromaterialbearbeitung mit ultrakurzen Laserimpulsen: Vorzüge, Probleme, Sicherheitsaspekte T2 - Seminar "Laser in der Feinbearbeitung" CY - Teltow, Germany DA - 2005-10-22 PY - 2005 AN - OPUS4-10950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas A1 - Martin, S. A1 - Kautek, Wolfgang A1 - Krüger, Jörg ED - Maruray, L. T1 - Ultra-short Pulse Laser Safety - a Challenge to Materials Science N2 - In this paper, safety-related experiments with ultra-short laser pulses (down to 30 fs) on various components (goggles, curtains) for laser protection are presented. The damage and failure behaviour of protective devices has been investigated dependent on practical conditions such as pulse duration, laser .uence, pulse number, and repetition rate. The e.ects of laser-irradiation on materials can be roughly divided into transient ones like laserinduced transmission (LIT) or short-lived colour centres and permanent damages like the stable colour centres and ablation. The former e.ects are particularly important for transparent devices like laser goggles. To obtain a complete overview on laser safety issues and the prevention of failure there are two important .elds of investigation: 1. the e.ects of laser radiation on human eyes and skin, and 2. on the possible protection materials. Both .elds have been addressed during the recently .nished German project SAFEST (safety aspects in femtosecond technology). The amount of safety data available in the ultrashort pulse region has been increased remarkably. This allows for a re-evaluation of known laser protection materials for this region of pulse durations and for the evaluation of new designs that promise high protection levels while being light-weight and convenient to use. T2 - Optical design and engineering II CY - Jena, Germany DA - 2005-09-13 PY - 2005 N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE IS - 5962 SP - 59622J-1 - 59622J-10 PB - SPIE CY - Bellingham AN - OPUS4-11593 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rudolph, Pascale A1 - Pentzien, Simone A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - König, E. T1 - Laserreinigung von Pergament und Papier PY - 1998 SN - 0933-4017 IS - 6 SP - 396 EP - 402 PB - Callwey CY - München AN - OPUS4-11598 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Sorg, N. A1 - Reif, J. A1 - Kautek, Wolfgang T1 - In situ second harmonic generation measurements during the electrodeposition of Ni on n-Si(111) PY - 1993 SN - 0169-4332 SN - 1873-5584 VL - 69 SP - 388 EP - 392 PB - North-Holland CY - Amsterdam AN - OPUS4-11657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sorg, N. A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - SHG Measurements of n-Si(111)/aqueous Solution Interfaces PY - 1993 SN - 0005-9021 VL - 97 IS - 3 SP - 402 EP - 406 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-11658 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kautek, Wolfgang A1 - Mitterer, S. A1 - Krüger, Jörg A1 - Husinsky, W. A1 - Grabner, G. T1 - Femtosecond-Pulse Laser Ablation of Human Corneas N2 - A femtosecond pulse laser in the visible spectral region shows promise as a potentially new powerful corneal sculpting tool. It combines the clinical and technical advantages of visible wavelengths with the high ablation quality observed with nanosecond-pulse excimer lasers at 193 nm. A femtosecond and a nanosecond dye laser with pulse durations of 300 fs and 7 ns, and centre wavelengths at 615 nm and 600 nm, respectively, both focused to an area of the order of 10–5 cm2, have been applied to human corneal ablation. Nanosecond laser pulses caused substantial tissue disruption within a 30–100 m range from the excision edge at all fluences above the ablation threshold of F th60 J cm–2 (I th9 GW cm–2). Completely different excisions are produced by the femtosecond-pulse laser: high quality ablations of the Bowman membrane and the stroma tissue characterised by damage zones of less than 0.5 m were observed at all fluences above ablation threshold of F th1 J cm–2 or I th3 TW cm–2 (3×1012 W cm–2). The transparent cornea material can be forced to absorb ultrashort pulses of extremely high intensity. The fs laser generates its own absorption by a multiphoton absorption process. PY - 1994 DO - https://doi.org/10.1007/BF00332446 SN - 0947-8396 VL - 58 IS - 5 SP - 513 EP - 518 PB - Springer CY - Berlin AN - OPUS4-11659 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kautek, Wolfgang A1 - Sorg, N. A1 - Krüger, Jörg T1 - Femtosecond pulse laser second harmonic generation on semiconductor electrodes KW - Femtosecond pulse laser KW - Second harmonic generation (SHG) KW - Electrochemistry KW - Semiconductor electrode KW - Silicon KW - Silicon oxide KW - Oxide growth PY - 1994 SN - 0013-4686 SN - 1873-3859 VL - 39 IS - 8/9 SP - 1245 EP - 1249 PB - Elsevier Science CY - Kidlington AN - OPUS4-11660 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kautek, Wolfgang A1 - Krüger, Jörg ED - Brieger, M. T1 - Femtosecond-pulse laser microstructuring of semiconducting materials T2 - 1st International Symposium on Semiconductor Processing and Characterization with Lasers - Applications in Photovoltaics CY - Stuttgart, Germany DA - 1994-04-18 KW - Femtosecond-Pulse Laser KW - Subpicosecond-Pulse Laser KW - Laser-Ablation KW - Multi-Photon Absorption KW - Microstructuring KW - Dry Etching KW - Semiconductors KW - Silicon PY - 1995 SN - 0-87849-683-1 SN - 0255-5476 N1 - Serientitel: Materials science forum – Series title: Materials science forum IS - 173/174 SP - 17 EP - 22 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-11671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kautek, Wolfgang A1 - Sorg, N. A1 - Krüger, Jörg ED - Brieger, M. T1 - Optical second-harmonic generation (SHG) on semiconductor electrodes by means of femtosecond and nanosecond-pulse lasers N2 - In situ optical second-harmonic generation (SHG) on centrosymmetric crystalline semiconductor electrodes opens up a new field of in situ investigations of hurried solid state interfaces and metal front contacts relevant to electronic and photovoltaic devices, which are rarely accessible by other methods. Photoelectrochemical nanosecond- and femtosecond-pulse laser investigations of silicon (111) electrodes show that in situ SHG is feasible in such complex interfacial systems. In a p-p polarization configuration, the azimuthal dependence of the SHG from oxide-covered and bare n-Si (111) electrodes, with and without Ni contact deposits, have been studied. Etching and regrowth of silicon oxides as well as burried interfacial electric field distributions were monitored. In situ SHG is shown to be extremely sensitive to trapped interfacial charge, crystal misorientations and surface step arrays. An advantage of femtosecond-pulses is the fact that illumination fluences that are well below the damage threshold, but still with sufficient power density, can be applied. (Author) T2 - 1st International Symposium on Semiconductor Processing and Characterization with Lasers - Applications in Photovoltaics CY - Stuttgart, Germany DA - 1994-04-18 KW - Femtosecond-Pulse Laser KW - Sub-Picosecond-Pulse Laser KW - Semiconductors KW - Silicon KW - Second-Harmonic Generation KW - SHG KW - Nonlinear Electroreflectance KW - Etch Process KW - Oxide KW - Interfacial Electronic States KW - Fermi-Level Pinning KW - MOS Diode PY - 1995 SN - 0-87849-683-1 DO - https://doi.org/10.4028/www.scientific.net/MSF.173-174.285 SN - 0255-5476 N1 - Serientitel: Materials science forum – Series title: Materials science forum IS - 173/174 SP - 285 EP - 290 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-11672 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Short pulse laser processing: safety aspects T2 - Bereichsseminar A - Max Born Institut Berlin CY - Berlin, Germany DA - 2006-11-30 PY - 2006 AN - OPUS4-13779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Sicherheit in der Anwendung der Femtosekunden-Lasertechnologie T2 - Mitgliederversammlung Laserverbund Berlin/Brandenburg CY - Berlin, Germany DA - 2007-01-18 PY - 2007 AN - OPUS4-14455 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wurster, R. A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Krüger, Jörg T1 - Characterization of laser-generated microparticles by means of a dust monitor and SEM imaging N2 - Nanosecond laser (1064 nm wavelength) cleaning of artificially soiled paper as a model sample simulating a real-world artwork was performed. During the cleaning process, the ejection of particles was monitored in situ by means of a dust monitor (8 size classes, ranging from 0.3 µm to >2 µm) and ex situ using a mini-cascade impactor (MKI, 5 stages). The cleaning result was analyzed by scanning electron microscopy (SEM) considering possible laser-induced damages to the substrate. Size distributions of emitted particles were measured depending on the processing parameters: laser fluence, F, and pulse number per spot, N. High numbers of large (>2 µm) particles were collected by the mini-cascade impactor indicating a gas dynamical liftoff process. Obviously, these particles were not affected by the laser-matter interaction. The different methods (SEM, MKI, and dust monitor) are compared with respect to their usefulness for a proper interpretation of the cleaning results. PY - 2006 DO - https://doi.org/10.1155/2006/31862 SN - 0278-6273 SN - 1476-3516 VL - 2006 IS - Article ID 31862 SP - 1 EP - 5(?) PB - Harwood Academic Publ. CY - London AN - OPUS4-14467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Laser-Reinigung von Papier, Pergament und Gewebe T2 - OpTecBB-Fokusseminar "Cultural Heritage", PTB CY - Berlin, Germany DA - 2007-05-03 PY - 2007 AN - OPUS4-14761 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Nanosecond laser damage resistance of optical multimode fibers prepared differently T2 - EMRS 2007 Spring Meeting, Symposium P: Laser synthesis and processing of advanced materials CY - Strasbourg, France DA - 2007-05-28 PY - 2007 AN - OPUS4-14762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Cleaning of artificially soiled paper with 532-nm nanosecond laser radiation T2 - EMRS 2007 Spring Meeting, Symposium S: Science & Technology of Cultural heritage Materials : Art conservation and Restoration CY - Strasbourg, France DA - 2007-05-28 PY - 2007 AN - OPUS4-14763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hertwig, Andreas A1 - Krüger, Jörg A1 - Weise, Matthias A1 - Beck, Uwe T1 - Hydrogen-Containing Amorphous Carbon Layers as Optical Materials in the Near-IR Spectral Range N2 - Hydrogenated amorphous carbon layers were deposited on various substrates by means of a plasma CVD process with a RF substrate bias as well as an ECR plasma source. The optical properties of the a-C:H layers were obtained via spectroscopic ellipsometry and correlated with their mechanical and chemical properties. The layers from pure RF plasma exhibit a higher absorption constant in the visible spectral range and a higher refractive index. All layers are nearly transparent in the NIR spectral range making them candidates for optical thin layer systems. The laser damage behaviour of the a-C:H layers was investigated with ultrashort pulses. The damage thresholds were consistent with the absorption constants of the layers. Interesting damage morphologies were observed indicating a sensitivity of this experiment to sub-structures in the layer. KW - Kohlenstoffschichten KW - Optische Konstanten KW - Ellipsometrie KW - Laser-Material-Bearbeitung KW - Amorphous KW - Diamond-like carbon KW - Hydrocarbons KW - Laser ablation KW - Optical proper PY - 2007 SN - 1612-8850 SN - 1612-8869 VL - 4 IS - S1 SP - S76 EP - S82 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-14862 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Nanosecond laser-induced surface damage of preforms and optical multimode fibers T2 - COLA 2007, Conference on Laser Ablation, Guia de Isora CY - Tenerife, Spain DA - 2007-09-24 PY - 2007 AN - OPUS4-14956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Laser-induced damage threshold (LIDT) testing of oxide and metal coatings with sub-30 fs pulses T2 - Workshop on Laser-Induced Damage (LZH Hannover) CY - Hanover, Germany DA - 2007-07-04 PY - 2007 AN - OPUS4-14979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Laser-Reinigung von Papier, Pergament und Gewebe - Eine Einführung T2 - Fachtagung, Hochschule für Angewandte Wissenschaft und Kunst (HAWK) CY - Hildesheim, Germany DA - 2007-10-01 PY - 2007 AN - OPUS4-15722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Dufft, Daniela A1 - Koter, Robert A1 - Hertwig, Andreas T1 - Femtosecond laser-induced damage of gold films N2 - Single- and multi-shot ablation thresholds of gold films in the thickness range of 31–1400 nm were determined employing a Ti:sapphire laser delivering pulses of 28 fs duration, 793 nm center wavelength at 1 kHz repetition rate. The gold layers were deposited on BK7 glass by an electron beam evaporation process and characterized by atomic force microscopy and ellipsometry. A linear dependence of the ablation threshold fluence Fth on the layer thickness d was found for d ≤ 180 nm. If a film thickness of about 180 nm was reached, the damage threshold remained constant at its bulk value. For different numbers of pulses per spot (N-on-1), bulk damage thresholds of ~0.7 J cm-2 (1-on-1), 0.5 J cm-2 (10-on-1), 0.4 J cm-2 (100-on-1), 0.25 J cm-2 (1000-on-1), and 0.2 J cm-2 (10000-on-1) were obtained experimentally indicating an incubation behavior. A characteristic layer thickness of Lc ˜ 180 nm can be defined which is a measure for the heat penetration depth within the electron gas before electron–phonon relaxation occurs. Lc is by more than an order of magnitude larger than the optical absorption length of α-1 ˜ 12 nm at 793 nm wavelength. KW - Single- and multi-shot ablation KW - Ti:sapphire laser KW - Gold films PY - 2007 SN - 0169-4332 SN - 1873-5584 VL - 253 IS - 19 SP - 7815 EP - 7819 PB - North-Holland CY - Amsterdam AN - OPUS4-15686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Engel, P. A1 - Krüger, Jörg A1 - Lußky, Katharina A1 - Pentzien, Simone T1 - Analyse häufig verwendeter europäischer Papiere. Im Fokus: Fasermaterial, Füllstoffe und Leimung N2 - Restauratoren können verschiedene Papierarten mit dem bloßen Auge aufgrund von Merkmalen in der Textur und der Oberflächenbeschaffenheit, seinem Aussehen im Durchlicht sowie an Griff und Klang grob unterscheiden. Dabei ist sich der Restaurator stets der Tatsache bewusst, dass es sich lediglich um eine erste grobe Einschätzung handeln kann. Erst bei mikroskopischen Analysen und physikalischen Experimenten treten Charakteristika zu Tage, die eine weitere Annäherung an die Zusammensetzung des Papiers und damit seiner Provenienz erlauben. Gegenstand dieser Arbeit war es, ein europäisches Hadernpapier, ein holzhaltiges Zeichenpapier und ein Whatman®-Filterpapier mit zwei mikroskopischen Methoden und einer Verbrennungstechnik zu untersuchen. Das Fasermaterial, die Füllstoffe, die Leimung und eventuelle Verunreinigungen wurden detailliert evaluiert. Neben konventioneller Lichtmikroskopie kam die weniger bekannte Umweltrasterelektronenmikroskopie (ESEM = Environmental Scanning Electron Microscopy) zum Einsatz, die neben der bildlichen Darstellung der Probenoberflächen zusätzlich eine Elementanalyse derselben gestattet. Letzteres erfordert allerdings das Vorhandensein eines zusätzlichen Röntgenspektrometers. Darüber hinaus wurden die verschiedenen Papiere trocken verascht. Es wurde eine oxidative Zerstörung der organischen Stoffe gewährleistet bis nur noch nichtbrennbare mineralische Asche zu verzeichnen war. Die Komplementarität der eingesetzten Methoden wird demonstriert und ein Einblick in die Zusammensetzung und Struktur der Papiere ermöglicht. Die Analysemethoden sind durch ihren partiell zerstörenden Charakter bzw. Limitierungen hinsichtlich der Objektgröße nur bedingt für die Untersuchung am Original geeignet, sehr wohl aber dafür, das Probenmaterial für Versuchsreihen genau zu definieren und zu standardisieren. PY - 2007 SN - 0933-4017 IS - 7 SP - 472 EP - 477 PB - Callwey CY - München AN - OPUS4-16046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Femtosecond laser interactions with dielectrics and polymers T2 - 4th Users Meeting of the European Network Laserlab-Europe CY - Madrid, Spain DA - 2007-11-28 PY - 2007 AN - OPUS4-16071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mann, Guido A1 - Vogel, Jens A1 - Preuß, Rüdiger A1 - Vaziri, Pouya A1 - Zoheidi, M. A1 - Eberstein, Markus A1 - Krüger, Jörg T1 - Nanosecond laser damage resistance of differently prepared semi-finished parts of optical multimode fibers N2 - Optical multimode fibers are applied in materials processing (e.g. automotive industry), defense, aviation technology, medicine and biotechnology. One challenging task concerning the production of multimode fibers is the enhancement of laser-induced damage thresholds. A higher damage threshold enables a higher transmitted average power at a given fiber diameter or the same power inside a thinner fiber to obtain smaller focus spots. In principle, different material parameters affect the damage threshold. Besides the quality of the preform bulk material itself, the drawing process during the production of the fiber and the preparation of the fiber end surfaces influence the resistance. Therefore, the change of the laser-induced damage threshold of preform materials was investigated in dependence on a varying thermal treatment and preparation procedure. Single and multi-pulse laser-induced damage thresholds of preforms (F300, Heraeus) were measured using a Q-switched Nd:YAG laser at 1064 nm wavelength emitting pulses with a duration of 15 ns, a pulse energy of 12 mJ and a repetition rate of 10 Hz. The temporal and spatial shape of the laser pulses were controlled accurately. Laser-induced damage thresholds in a range from 150 J cm-2 to 350 J cm-2 were determined depending on the number of pulses applied to the same spot, the thermal history and the polishing quality of the samples, respectively. KW - Laser ablation KW - Optical fibers KW - Physical radiation damage KW - Radiation treatment KW - Glass transitions KW - Glasses PY - 2007 DO - https://doi.org/10.1016/j.apsusc.2007.09.032 SN - 0169-4332 SN - 1873-5584 VL - 254 IS - 4 SP - 1096 EP - 1100 PB - North-Holland CY - Amsterdam AN - OPUS4-16207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mäder, M. A1 - Holle, H. A1 - Schreiner, M. A1 - Pentzien, Simone A1 - Krüger, Jörg A1 - Kautek, Wolfgang ED - Johann Nimmrichter, ED - Kautek, Wolfgang ED - Manfred Schreiner, T1 - Traditional and laser cleaning methods of historic picture post cards T2 - LACONA VI CY - Vienna, Austria DA - 2005-09-21 KW - Laser KW - Cleaning KW - Picture Post Card PY - 2007 SN - 978-3-540-72129-1 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics IS - 116 SP - 281 EP - 286 PB - Springer CY - Berlin AN - OPUS4-16378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lerber, K. von A1 - Strlic, M. A1 - Kolar, J. A1 - Krüger, Jörg A1 - Pentzien, Simone A1 - Kennedy, C. A1 - Wess, T. A1 - Sokhan, M. A1 - Kautek, W. ED - Johann Nimmrichter, ED - Kautek, Wolfgang ED - Manfred Schreiner, T1 - Laser cleaning of undyed silk: Indications of chemical change T2 - LACONA VI CY - Vienna, Austria DA - 2005-09-21 KW - Laser KW - Cleaning KW - Silk KW - Textiles KW - Viscometry KW - X-ray diffraction KW - SIMS PY - 2007 SN - 978-3-540-72129-1 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics IS - 116 SP - 313 EP - 319 PB - Springer CY - Berlin AN - OPUS4-16379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg A1 - Pentzien, Simone A1 - Lerber, K. von ED - Johann Nimmrichter, ED - Kautek, Wolfgang ED - Manfred Schreiner, T1 - Determination of a working range for the laser cleaning of soiled silk T2 - LACONA VI CY - Vienna, Austria DA - 2005-09-21 KW - Laser KW - Cleaning KW - Silk KW - Textiles PY - 2007 SN - 978-3-540-72129-1 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics IS - 116 SP - 321 EP - 327 PB - Springer CY - Berlin AN - OPUS4-16380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Spielmann, C. T1 - Femtosecond Laser Technology in Use: Safety Aspects - A Detailed Study compares different Materials for Eye Protection N2 - In recent years, femtosecond lasers matured from sensitive research setups to turnkey systems for an increasing number of applications. Now that running an ultra-short pulse laser system needs no longer a specialized scientist, safety issues become more crucial. Ultrashort laser pulses have extremely high peak powers and even scattered radiation may possess severe risks to the unprotected eye. Accordingly, special protection schemes are necessary for these unique laser systems. PY - 2008 DO - https://doi.org/10.1002/latj.200790209 SN - 1613-7728 VL - 5 IS - 1 SP - 48 EP - 52 PB - Wiley-VCH CY - Weinheim AN - OPUS4-16471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Laser-induzierte Zerstörung von optischen Komponenten bei Anwendung von Femtosekunden-Impulsen T2 - Workshop Lasermikrobearbeitung CY - Berlin, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-16676 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rohloff, M. A1 - Das, S.K. A1 - Höhm, S. A1 - Grunwald, R. A1 - Rosenfeld, A. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Formation of laser-induced periodic surface structures on fused silica upon multiple cross-polarized double-femtosecond-laser-pulse irradiation sequences N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of fused silica with multiple irradiation sequences consisting of five Ti:sapphire femtosecond (fs) laser pulse pairs (150 fs, 800 nm) is studied experimentally. A Michelson interferometer is used to generate near-equal-energy double-pulse sequences with a temporal pulse delay from -20 to +20 ps between the cross-polarized individual fs-laser pulses (~0.2 ps resolution). The results of multiple double-pulse irradiation sequences are characterized by means of Scanning Electron and Scanning Force Microscopy. Specifically in the sub-ps delay domain striking differences in the surface morphologies can be observed, indicating the importance of the laser-induced free-electron plasma in the conduction band of the solids for the formation of LIPSS. KW - Atomic force microscopy KW - Conduction bands KW - High-speed optical techniques KW - Laser beam effects KW - Scanning electron microscopy KW - Silicon compounds KW - Surface morphology PY - 2011 DO - https://doi.org/10.1063/1.3605513 SN - 0021-8979 SN - 1089-7550 VL - 110 IS - 1 SP - 014910-1 - 014910-4 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-24049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Femtosecond, picosecond and nanosecond pulse laser cleaning of artificially soiled paper model samples T2 - Konferenz "Laser in the Conservation of Artworks" (LACONA IX) CY - London, England DA - 2011-09-07 PY - 2011 AN - OPUS4-24238 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Fixation of bioactive calcium phosphate on Ti6AI4V with e femtosecond laser T2 - Jahrestagung der Deutschen Gesellschaft für Biomaterialien (DGBM) CY - Giessen, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geier, M. A1 - Eberstein, M. A1 - Grießmann, H. A1 - Partsch, U. A1 - Völkel, L. A1 - Böhme, R. A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Impact of laser treatment on phosphoric acid coated multicrystalline silicon PV-wafers N2 - The selective emitter is a well-known technology for producing highly doped areas under the metallization grid to improve the solar cell performance. In this work, the influence of laser irradiation on phosphoric acid coated multicrystalline silicon PV-wafers on the wafer surface structure, the phosphorous depth distribution and the electrical contact resistance within the laser treated area as well as the electrical series resistance of laserprocessed solar cells was evaluated. Different laser processing settings were tested including pulsed and continuous wave (cw) laser sources (515 nm, 532 nm, 1064 nm wavelength). Complementary numerical simulations using the finite element method (FEM) were conducted to explain the impact of the laser parameters on the melting behavior (melt duration and geometry). It was found that the melt duration is a key parameter for a successful laser Doping process. Our simulations at a laser wavelengths of 515 nm reveal that low-repetition rate (<500 kHz) laser pulses of 300 ns duration generate a melt duration of ~0.35 µs, whereas upon scanning cw-laser radiation at 532 nm prolongates the melt duration by at least one order of magnitude. Experimentally, the widely used ns-laser pulses did not lead to satisfying laser irradiation results. In contrast, cw-laser radiation and scan velocities of less than 2 m/s led to suitable laser doping featuring low electrical resistances in the laser treated areas. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.2011 KW - Silicon solar cell KW - Selective emitter KW - Laser processing KW - Doping KW - Simulation PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-2BV.1.7 SP - 1243 EP - 1247 AN - OPUS4-24995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberstein, M. A1 - Geier, M. A1 - Grießmann, H. A1 - Partsch, U. A1 - Voelkel, L. A1 - Böhme, R. A1 - Pentzien, Simone A1 - Koter, Robert A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Towards an industrial laser doping process for the selective emitter using phosphoric acid as dopant N2 - Different laser supported approaches have already been realized, proving the great potential of laserdoped selective emitters (LDSE). However, it is challenging to establish a low-cost process by using pulsed laser tools. So far a single-step process only leads to satisfying results utilizing cw-lasers. In this paper we have examined a two-step process to produce laser-doped selective emitters on multicrystalline textured standard silicon photovoltaic wafers (90-Ω/sq-Emitter, SiN-antireflection coating (ARC)). The precise ARC removal by near-infrared fs-laser pulses (30 fs, 800 nm), and the doping of uncoated silicon wafers by ns-laser pulses (8 ns, 532 nm) were systematically investigated. In the fs-experiment, optimum conditions for ARC removal were identified. In the nsexperiments under suitable conditions (melting regime), the phosphorous concentration underneath the wafer surface was significantly increased and the sheet resistance was reduced by nearly a factor of two. Moreover, electrical measurements on fired metallization fingers deposited on the laser processed wafers showed low contact resistances. Hence, wafer conditioning with combined fs-laser- and ns-laser-processes are expected to be a promising technology for producing selective emitters. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.2011 KW - Laser processing KW - Doping KW - Selective emitter KW - Multicrystalline silicon PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-2BV.1.2 SP - 1220 EP - 1223 AN - OPUS4-24996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Herstellung von keramischen Implantatbeschichtungen mittels fs-Laserpulsen T2 - Innovationsforum MikroLas CY - Rostock, Germany DA - 2012-03-06 PY - 2012 AN - OPUS4-25526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Krüger, Jörg A1 - Höhm, S. A1 - Rosenfeld, A. T1 - Femtosecond laser-induced periodic surface structures N2 - The formation of laser-induced periodic surface structures (LIPSS) in different materials (metals, semiconductors, and dielectrics) upon irradiation with linearly polarized fs-laser pulses (τ~30–150 fs, λ~800 nm) in air environment is studied experimentally and theoretically. In metals, predominantly low-spatial-frequency-LIPSS with periods close to the laser wavelength λ are observed perpendicular to the polarization. Under specific irradiation conditions, high-spatial-frequency-LIPSS with sub-100-nm spatial periods (~λ/10) can be generated. For semiconductors, the impact of transient changes of the optical properties to the LIPSS periods is analyzed theoretically and experimentally. In dielectrics, the importance of transient excitation stages in the LIPSS formation is demonstrated experimentally using (multiple) double-fs-laser-pulse irradiation sequences. A characteristic decrease of the LIPSS periods is observed for double-pulse delays of less than 2 ps. KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Ultrafast optical techniques KW - Silicon KW - Titanium KW - Silica PY - 2012 DO - https://doi.org/10.2351/1.4712658 SN - 1042-346X SN - 1938-1387 VL - 24 IS - 4 SP - 042006-1 EP - 042006-7 PB - Laser Institute of America CY - Orlando, Fla., USA AN - OPUS4-26198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mann, Guido A1 - Zoheidi, M. A1 - Krüger, Jörg T1 - High performance fibers at the limit N2 - Because of the increasingly stringent requirements for fibers in high Performance applications, the Business Unit Fiber Optics of the Leoni Group and the German BAM Federal Institute for Materials Research and Testing are jointly tackling the challenge of investigating the damage thresholds of selected large core special fibers for the first time. KW - Laser-induced damage threshold KW - Optical multimode fiber KW - Nanosecond laser PY - 2013 SN - 1610-3521 IS - Laser+Photonics Exportausgabe 2013 SP - 20 EP - 23 PB - Hanser CY - München AN - OPUS4-27679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Mann, Guido A1 - Krüger, Jörg A1 - Marcinkowski, M. A1 - Eberstein, M. T1 - Femtosecond laser-induced removal of silicon nitride layers from doped and textured silicon wafers used in photovoltaics N2 - The removal of a 75- to 90-nm-thick passivating silicon nitride antireflection coating from standard textured multicrystalline silicon photovoltaic wafers with a typical diffused 90-Ω/sq-emitter upon irradiation with near-infrared femtosecond laser pulses (790 nm central wavelength, 30 fs pulse duration) is studied experimentally. The laser irradiation areas are subsequently characterized by complementary optical microscopy, scanning electron microscopy and depth profiling chemical analyses using secondary ion mass spectrometry. The results clarify the thin-film femtosecond laser ablation scenario and outline the process windows for selective antireflection coating removal. KW - Photovoltaics KW - Solar cell KW - Laser processing KW - FS-laser ablation KW - Silicon nitride PY - 2013 DO - https://doi.org/10.1016/j.tsf.2013.07.005 SN - 0040-6090 VL - 542 SP - 420 EP - 425 PB - Elsevier CY - Amsterdam AN - OPUS4-28874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotsifaki, D.G. A1 - Zekou, L. A1 - Pentzien, Simone A1 - Krüger, Jörg A1 - Serafetinides, A.A. ED - Saunders, D. ED - Strlic, M. ED - Korenberg, C. ED - Luxford, N. ED - Birkhölzer, K. T1 - Cleaning of artificially soiled papers by infrared and mid-infrared lasers N2 - One of the most important materials presenting and witnessing human culture is paper. The cleaning of paper is often necessary because contamination must be removed so that the fragile organic substrate can be preserved. The conventional cleaning methods are mechanical or involve the application of chemicals. These methods can damage drawings or print layers to some extent or make the original paper substrate brittle. More specifically, the use of a scalpel blade can cause damage to fibers. Chemical cleaning is difficult to perform locally, can dissolve foreign matter that then migrates into the paper substrate, or involves volatile organic compounds that can be harmful to the conservator. There is, therefore, a need for new conservation technologies aimed at the safe cleaning of paper. Lasers have proved to be an appropriate tool for cleaning as the energy dose and penetration depth at the specific point of contamination can be controlled. Additionally, if used properly, laser cleaning is not destructive to the paper. T2 - LACONA IX - Lasers in the conservation of artworks CY - London, UK DA - 07.09.2011 KW - Laser cleaning KW - Paper KW - Artificial soiling KW - Nanosecond laser KW - Microsecond laser PY - 2013 SN - 978-1-904982-87-6 SP - 219 EP - 221 PB - Archetype publications Ltd. AN - OPUS4-27956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohamed, Zeinab A1 - Krüger, Simone A1 - Friedrich, Jörg Florian T1 - Deposition of thick polymer or inorganic layers with flame-retardant properties by combination of plasma and spray processes N2 - Mixtures of hexamethyldisiloxane (HMDSO) and oxygen have been used for deposition of SiO2-like layers by plasma polymerization under low-pressure conditions onto polyethylene and polystyrene used as basecoat. Water glass was cast onto these 0.5 pm plasma thick siloxane-like layers with a thickness of 5 to 40 mu m. The adhesion of these bilayer systems and their flame resistance were tested. The effect of different plasma parameters such as monomer/gas ratio, pressure and power input into the discharge on the deposition rate and the composition of the formed layers was studied. Characterization and chemical composition of the formed films were performed using infrared, X-ray photoelectron and solid state nuclear magnetic resonance spectroscopy. Peel strengths of composites were measured and the locus of peel front propagation was detected. Thermal properties of composites were analyzed by thermo-gravimetric analysis. Finally, the fire-retardant properties of thick coated polymers were determined by exposure to flames and the behavior of coatings on the polymers during flaming was observed visually. T2 - 3. Magdeburger Brand- und Explosionsschutztag / vfdb-Workshop CY - Magdeburg, Germany DA - 21.03.2013 KW - Polymer KW - Plasmatechnologie KW - Analytik PY - 2013 SN - 978-3-00-041601-9 SP - 1 EP - 11 AN - OPUS4-27988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Covering Ti6Al4V implant material with bioactive ceramics using femtosecond laser processing T2 - 5th European Conference on Applications of Femtosecond Lasers in Materials Science (FemtoMat 2013) CY - Mauterndorf, Austria DA - 2013-03-18 PY - 2013 AN - OPUS4-28048 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Höhm, S. A1 - Rohloff, M. A1 - Rosenfeld, A. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Dynamics of the formation of laser-induced periodic surface structures on dielectrics and semiconductors upon femtosecond laser pulse irradiation sequences N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of fused silica and silicon with multiple (NDPS) irradiation sequences consisting of linearly polarized femtosecond laser pulse pairs (pulse duration ~150 fs, central wavelength ~800 nm) is studied experimentally. Nearly equal-energy double-pulse sequences are generated allowing the temporal pulse delay Δt between the cross-polarized individual fs-laser pulses to be varied from -40 ps to +40 ps with a resolution of ~0.2 ps. The surface morphologies of the irradiated surface areas are characterized by means of scanning electron and scanning force microscopy. Particularly for dielectrics in the sub-ps delay range striking differences in the orientation and spatial characteristics of the LIPSS can be observed. For fused silica, a significant decrease of the LIPSS spatial periods from ~790 nm towards ~550 nm is demonstrated for delay changes of less than ~2 ps. In contrast, for silicon under similar irradiation conditions, the LIPSS periods remain constant (~760 nm) for delays up to 40 ps. The results prove the impact of laser-induced electrons in the conduction band of the solid and associated transient changes of the optical properties on fs-LIPSS formation. PY - 2013 DO - https://doi.org/10.1007/s00339-012-7184-z SN - 0947-8396 VL - 110 IS - 3 SP - 553 EP - 557 PB - Springer CY - Berlin AN - OPUS4-27787 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Höhm, S. A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Sub-100-nm laser-induced periodic surface structures upon irradiation of titanium by Ti:sapphire femtosecond laser pulses in air N2 - The formation of laser-induced periodic surface structures (LIPSS) on titanium upon irradiation with linearly polarized femtosecond (fs) laser pulses (τ = 30 fs, λ = 790 nm) in an air environment is studied experimentally and theoretically. In the experiments, the dependence on the laser fluence and the number of laser pulses per irradiation spot has been analyzed. For a moderate number of laser pulses (N < 1000) and at fluences between ~0.09 and ~0.35 J/cm², predominantly low-spatial-frequency-LIPSS with periods between 400 nm and 800 nm are observed perpendicular to the polarization. In a narrow fluence range between 0.05 and 0.09 J/cm², high-spatial-frequency-LIPSS with sub-100-nm spatial periods (~λ/10) can be generated with an orientation parallel to the polarization (N = 50). These experimental results are complemented by calculations based on a theoretical LIPSS model and compared to the present literature. PY - 2013 DO - https://doi.org/10.1007/s00339-012-7140-y SN - 0947-8396 VL - 110 IS - 3 SP - 547 EP - 551 PB - Springer CY - Berlin AN - OPUS4-27788 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Höhm, S. A1 - Rosenfeld, A. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Femtosecond diffraction dynamics of laser-induced periodic surface structures on fused silica N2 - The formation of laser-induced periodic surface structures (LIPSS) on fused silica upon irradiation with linearly polarized fs-laser pulses (50 fs pulse duration, 800?nm center wavelength) is studied experimentally using a transillumination femtosecond time-resolved (0.1 ps-1 ns) pump-probe diffraction approach. This allows to reveal the generation dynamics of near-wavelength-sized LIPSS showing a transient diffraction at specific spatial frequencies even before a corresponding permanent surface relief was observed. The results confirm that the ultrafast energy deposition to the materials surface plays a key role and triggers subsequent physical mechanisms such as carrier scattering into self-trapped excitons. KW - High-speed optical techniques KW - Laser beam effects KW - Silicon compounds KW - Surface structure PY - 2013 DO - https://doi.org/10.1063/1.4790284 SN - 0003-6951 SN - 1077-3118 VL - 102 IS - 5 SP - 054102-1 EP - 054102-4 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-27646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Höhm, S. A1 - Rosenfeld, A. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Area dependence of femtosecond laser-induced periodic surface structures for varying band gap materials after double pulse excitation N2 - The formation of laser-induced periodic surface structures upon irradiation of titanium, silicon, and fused silica with multiple irradiation sequences consisting of parallel polarized Ti:sapphire femtosecond laser pulse pairs (pulse duration 50–150 fs, central wavelength ~800 nm) is studied experimentally. The temporal delay between the individual near-equal energy fs-laser pulses was varied between 0 and 5 ps with a temporal resolution of better than 0.2 ps. The surface morphology of the irradiated surface areas is characterized by means of scanning electron microscopy (SEM). In all materials a decrease of the rippled surface area is observed for increasing delays. The characteristic delay decay scale is quantified and related to material dependent excitation and energy relaxation processes. KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Double-pulse experiments KW - Ultrafast optical techniques KW - Mach-Zehnder interferometer PY - 2013 DO - https://doi.org/10.1016/j.apsusc.2012.10.188 SN - 0169-4332 SN - 1873-5584 VL - 278 SP - 7 EP - 12 PB - North-Holland CY - Amsterdam AN - OPUS4-28601 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Hertwig, Andreas A1 - Koter, Robert A1 - Weise, Matthias A1 - Beck, Uwe A1 - Reinstädt, Philipp A1 - Griepentrog, Michael A1 - Krüger, Jörg A1 - Picquart, M. A1 - Haro-Poniatowski, E. T1 - Femtosecond laser pulse irradiation effects on thin hydrogenated amorphous carbon layers N2 - The irradiation of ~0.9-µm-thick hydrogenated amorphous carbon (a-C:H) layers deposited on silicon substrates with single femtosecond (fs) laser pulses (35 fs pulse duration, 790 nm centre wavelength) in air is studied experimentally. Irradiation spots have been generated with different peak fluences and subsequently investigated by optical topometry, micro Raman spectroscopy and microscale mechanical indentation in order to evaluate their microscopic, topographical, structural and mechanical properties (e.g. elastic modulus). By this multi-method approach, a clear separation of different effects (delamination and graphitisation) becomes possible. The joint application of mechanical and spectroscopic techniques provides unique insights into the effects of the fs-laser radiation on the carbon layer. PY - 2013 DO - https://doi.org/10.1007/s00339-012-7170-5 SN - 0947-8396 VL - 112 IS - 1 SP - 9 EP - 14 PB - Springer CY - Berlin AN - OPUS4-28629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mann, Guido A1 - Pentzien, Simone A1 - Krüger, Jörg T1 - Beam diameter dependence of surface damage threshold of fused silica fibers and preforms for nanosecond laser treatment at 1064 nm wavelength N2 - Optical fibers made of fused silica are a common method of transmitting high laser pulse energies. Failure of those fibers is a significant risk. The determination of laser-induced damage thresholds (LIDT) on fiber end facets according to ISO 21254 standard is needed. In the past, single pulse nanosecond laser experiments showed an improvement of LIDT with increasing fiber core diameter for 1064 nm wavelength and a constant beam diameter of 50 µm. This paper pays particular attention to the influence of the laser beam diameter on damage resistance. All-silica fiber types (LEONI) with different core diameters (100–600 µm) were investigated using beam diameters in a range from 30 µm to 100 µm. For comparison experiments on fused silica preform material (Heraeus F300) were performed. On one hand, surface LIDT of fused silica preform material decreases significantly with increasing beam size. A model considering a random distribution of point defects explains the experimental data qualitatively. On the other hand, LIDT of fiber end facets stays constant. White light microscopy results suggest that the point defect density on fiber end facets is lower compared to the preform surface due to an excellent surface polish quality. KW - Laser-induced damage threshold KW - Nanosecond laser KW - Optical fiber KW - Fused silica KW - Spot size KW - Defect model PY - 2013 DO - https://doi.org/10.1016/j.apsusc.2013.03.088 SN - 0169-4332 SN - 1873-5584 VL - 276 SP - 312 EP - 316 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-28310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mohamed, Zeinab A1 - Krüger, Simone A1 - Hidde, Gundula A1 - Schimanski, A. A1 - Jäger, Christian A1 - Friedrich, Jörg Florian T1 - Deposition of thick polymer or inorganic layers with flame-retardant properties by combination of plasma and spray processes N2 - Mixtures of hexamethyldisiloxane (HMDSO) and oxygen have been used for deposition of SiO2-like layers by plasma polymerization under low-pressure conditions onto polyethylene and polystyrene used as basecoat. Water glass was cast onto these 0.5 µm plasma thick siloxane-like layers with a thickness of 5 to 40 µm. The adhesion of these bilayer systems and their flame resistance were tested. The effect of different plasma parameters such as monomer/gas ratio, pressure and power input into the discharge on the deposition rate and the composition of the formed layers was studied. Characterization and chemical composition of the formed films were performed using infrared, X-ray photoelectron and solid state nuclear magnetic resonance spectroscopy. Peel strengths of composites were measured and the locus of peel front propagation was detected. Thermal properties of composites were analyzed by thermo-gravimetric analysis. Finally, the fire-retardant properties of thick coated polymers were determined by exposure to flames and the behavior of coatings on the polymers during flaming was observed visually. KW - Plasma polymerization KW - Hexamethyldisiloxane plasma polymer KW - Polystyrene KW - Polyethylene KW - Flame retardancy PY - 2013 DO - https://doi.org/10.1016/j.surfcoat.2013.04.039 SN - 0257-8972 VL - 228 SP - 266 EP - 274 PB - Elsevier B.V. CY - Lausanne AN - OPUS4-28735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg T1 - Beam diameter dependence of surface damage threshold of optical multimode fibers and preform material for 532 nm and 1064 nanosecond laser treatment T2 - European Materials Research Society (EMRS) Spring Meeting 2013, Symposium V "Laser materials interactions for micro and nano applications" CY - Strasbourg, France DA - 2013-05-27 PY - 2013 AN - OPUS4-28810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Derrien, Thibault A1 - Krüger, Jörg A1 - Itina, T.E. A1 - Höhm, S. A1 - Rosenfeld, A. A1 - Bonse, Jörn T1 - Rippled area formed by surface plasmon polaritons upon femtosecond laser double-pulse irradiation of silicon N2 - The formation of near-wavelength laser-induced periodic surface structures (LIPSS) on silicon upon irradiation with sequences of Ti:sapphire femtosecond laser pulse pairs (pulse duration 150 fs, central wavelength 800 nm) is studied theoretically. For this purpose, the nonlinear generation of conduction band electrons in silicon and their relaxation is numerically calculated using a two-temperature model approach including intrapulse changes of optical properties, transport, diffusion and recombination effects. Following the idea that surface plasmon polaritons (SPP) can be excited when the material turns from semiconducting to metallic state, the 'SPP active area' is calculated as function of fluence and double-pulse delay up to several picoseconds and compared to the experimentally observed rippled surface areas. Evidence is presented that multi-photon absorption explains the large increase of the rippled area for temporally overlapping pulses. For longer double-pulse delays, relevant relaxation processes are identified. The results demonstrate that femtosecond LIPSS on silicon are caused by the excitation of SPP and can be controlled by temporal pulse shaping. PY - 2013 DO - https://doi.org/10.1364/OE.21.029643 SN - 1094-4087 VL - 21 IS - 24 SP - 29643 EP - 29655 PB - Optical Society of America CY - Washington, DC AN - OPUS4-29650 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Wrobel, Jerzy A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - Ultrashort-pulse laser ablation of indium phosphide in air N2 - Ablation of indium phosphide wafers in air was performed with low repetition rate ultrashort laser pulses (130 fs, 10 Hz) of 800 nm wavelength. The relationships between the dimensions of the craters and the ablation parameters were analyzed. The ablation threshold fluence depends on the number of pulses applied to the same spot. The single-pulse ablation threshold value was estimated to be fth(1)=0.16 J/cm2. The dependence of the threshold fluence on the number of laser pulses indicates an incubation effect. Morphological and chemical changes of the ablated regions were characterized by means of scanning electron microscopy and Auger electron spectroscopy. PY - 2001 DO - https://doi.org/10.1007/s003390000596 SN - 0947-8396 VL - 72 IS - 1 SP - 89 EP - 94 PB - Springer CY - Berlin AN - OPUS4-1068 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Baudach, Steffen A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Welsch, E. T1 - Femtosecond laser damage of a high reflecting mirror N2 - Multiple pulse investigations of 130-fs Ti:sapphire laser-induced damage of a high reflecting mirror consisting of alternating ?/4-layers of Ta2O5 and SiO2 and a single 500-nm Ta2O5 film were performed. In both cases, fused silica served as the substrate. For a fixed number of 1000 laser pulses per spot, a decrease in the damage threshold fluence of the mirror by a factor of two was observed by changing the repetition rate from 10 Hz to 1 kHz. A single 500-nm Ta2O5 film shows higher damage resistance compared to the mirror. The mirror and the Ta2O5 film samples were partially coated with a 300-nm-thick aluminium layer. The aluminium coating does not influence the damage threshold of the dielectrics underneath. KW - Aluminium KW - Laser ablation KW - Optical coatings KW - Silicon oxide PY - 2002 DO - https://doi.org/10.1016/S0040-6090(02)00074-3 SN - 0040-6090 IS - 408 SP - 297 EP - 301 PB - Elsevier CY - Amsterdam AN - OPUS4-1382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krüger, Jörg A1 - Lenzner, Matthias A1 - Martin, Sven A1 - Lenner, M. A1 - Spielmann, C. A1 - Fiedler, A. A1 - Kautek, Wolfgang ED - Phipps, C. R. T1 - Femtosecond laser induced damage in absorbing filters used for laser protection N2 - Damage experiments of absorbing filters (Schott BG18 and BG36) were performed with Ti:sapphire laser pulses with durations from 30 fs to 340 fs (800 nm, 1 kHz) in air. The direct focusing technique was employed under single- and multi-pulse irradiation conditions. Ablation threshold fluences were determined from a semi-logarithmic plot of the ablation crater diameter vs. laser fluence. The damage threshold fluence decreases for shorter pulse durations. In the investigated pulse duration range, the measured multi-pulse ablation threshold fluences are practically similar to those of undoped glass material (~1 Jcm-2). That means that the multi-pulse ablation threshold is independent on the doping level of the filters. For more than 100 pulses per spot and all pulse durations applied, the threshold fluence saturates. This leads to technically relevant damage threshold values in the femtosecond laser pulse duration domain. T2 - 4th SPIE's International Conference on High-Power Laser Ablation CY - Taos, NM, USA DA - 2002-04-22 KW - Ablation KW - Damage KW - Eye protection KW - Femtosecond pulse laser KW - Incubation KW - Laser safety KW - Threshold fluence PY - 2002 SN - 0-8194-4524-X DO - https://doi.org/10.1117/12.482109 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series VL - 1 IS - 4760 SP - 398 EP - 405 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-1550 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kautek, Wolfgang A1 - Daminelli-Widany, Grazia A1 - Meja, P. A1 - Cortona, Anna A1 - Krüger, Jörg A1 - Autric, M. ED - Phipps, C. R. T1 - Femtosecond and nanosecond laser removal of anodic oxide layers from aluminium T2 - 4th SPIE's International Conference on High-Power Laser Ablation CY - Taos, NM, USA DA - 2002-04-22 KW - Laser ablation KW - Laser spallation KW - Microphone KW - Acoustical measurement KW - Aluminium oxide PY - 2002 SN - 0-8194-4524-X SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 4760 SP - 239 EP - 246 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-1551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Bonse, Jörn A1 - Lenzner, Matthias T1 - Modification and Ablation of Semiconductors by Femtosecond Laser Pulses N2 - Physical and chemical phenomena resulting from irradiation of silicon and indium phosphide with ultrashort laser pulses (~100fs) were investigated with respect to the difference between single- and multiple-pulse treatment. In the single-pulse case, several processes were identified: modification, recrystallization and ablation. All processes exhibit a distinct treshold behaviour. A two photon-absorption coefficient can be determined from a single spatial ablation profile. Accumulation effects were observed for multi-pulse illumination. Different morphological features like bubbles, rippels and microcolumns were found. PY - 2002 VL - 5 IS - 2 SP - 437 EP - 461 PB - Transworld Research Network CY - Trivandrum AN - OPUS4-1585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, Wolfgang A1 - Daminelli-Widany, Grazia A1 - Krüger, Jörg T1 - Femtosecond and Nanosecond Pulse Laser Electrochemistry of Aluminium Alloys T2 - 53th Annual meeting of the International Society of Electrochemistry CY - Düsseldorf, Germany DA - 2002-09-15 PY - 2002 SP - 1(?) PB - DECHEMA CY - Frankfurt a.M. AN - OPUS4-1586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Lenzner, Matthias A1 - Martin, Sven A1 - Lenner, M. A1 - Spielmann, C. A1 - Fiedler, A. ED - Meunier, M. T1 - Single- and multi-pulse femtosecond laser ablation of optical filter materials N2 - Commercially available absorption filters (Schott BG18 and BG36) were investigated with respect to their single- and multi-pulse ablation threshold using laser pulses from a Ti:Sapphire laser in the range between 30 and 340 fs. It could be observed, that the threshold fluence decreases for shorter pulse durations. The similarity of the measured multi-pulse threshold fluences with those of undoped glass material (around 1 J/cm^2 for a pulse duration of 30 fs) suggests that, for very short pulses, the threshold is independent on the doping level and therefore, linear absorption does not significantly contribute to laser-induced damage. For >100 pulses per spot and all pulse durations applied, the threshold fluences saturate. This independence on the number of applied pulses leads to technically relevant damage threshold values. T2 - Symposium D - European Materials Research Society CY - Strasbourg, France DA - 2002-06-18 PY - 2002 UR - http://www.emrs-strasbourg.com/files/pdf/2002_SPRING/02_Prog_Dv2.pdf N1 - Serientitel: Applied surface science – Series title: Applied surface science VL - 208/209.2003,1 IS - 1 SP - 1(?) PB - Elsevier CY - Amsterdam AN - OPUS4-1588 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, Wolfgang A1 - Martin, Sven A1 - Krüger, Jörg A1 - Lenzner, Matthias A1 - Fiedler, A. ED - Meunier, M. T1 - Femtosecond laser multi-pulse interaction with optical filters and fabrics N2 - Optical filters and fabrics are important parts of laser safety equipment such as goggles and curtains. A choice of these materials with varying absorption spectra is investigated with respect to their resistance to Ti:sapphire femtosecond laser radiation (800 nm wavelength, 1 kHz repetition rate). Pulse durations down to 30 fs and multiple-pulse irradiation conditions are employed to evaluate technically relevant damage thresholds. The ablation threshold fluences of the absorbing filters are comparable to those observed for transparent materials with 30-fs-pulses. These investigations together with scanning electron microscopy of the surface morphology after laser treatment provide insight into the interaction mechanism of the short pulses with the materials. T2 - Symposium D - European Materials Research Society CY - Strasbourg, France DA - 2002-06-18 PY - 2002 UR - http://www.emrs-strasbourg.com/files/pdf/2002_SPRING/02_Prog_Dv2.pdf N1 - Serientitel: Applied surface science – Series title: Applied surface science VL - 208/209.2003,1 IS - 1 SP - 1(?) PB - Elsevier CY - Amsterdam AN - OPUS4-1730 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, Wolfgang A1 - Daminelli-Widany, Grazia A1 - Krüger, Jörg ED - Meunier, M. T1 - Ultrashort pulse laser interaction with anodic metal oxide layers in electrolyte contact N2 - The removal and accelerated corrosion monitoring of metal coating systems is of general interest in materials science and engineering technology. The femtosecond and nanosecond laser ablation and delamination at 800 nm and 532 nm, respectively, of anodic oxide layers on aluminium alloys in electrolyte contact were investigated. Laser-induced modifications of the oxide layer resulted in an ionic contact between electrolyte and metal, which produced a current transient and thus allowed the in-situ electrochemical monitoring of the modification. Oxide coatings with different optical properties, almost transparent and opaque, were examined. The transparent anodic oxides showed contrasting ablation mechanisms in the nanosecond and femtosecond pulse duration regime: nanosecond pulses caused spallation, whereas femtosecond treatment led to ablation. Current signals measured in the transparent film were consistent with light absorption below the metal-oxide interface and with film spallation. Irradiation of the opaque coating yielded ionic current transients within the so-called shock-affected-zone of the oxide layer. This investigation provided insight into the role of the penetration depth of light and the heat-affected zone, the extent of the shock-affected zone, and the defect formation in the coating and at the solid-solid interface between metal and oxide. T2 - Symposium D - European Materials Research Society CY - Strasbourg, France DA - 2002-06-18 PY - 2002 UR - http://www.emrs-strasbourg.com/files/pdf/2002_SPRING/02_Prog_Dv2.pdf N1 - Serientitel: Applied surface science – Series title: Applied surface science VL - 208/209.2003,1 IS - 1 SP - 1(?) PB - Elsevier CY - Amsterdam AN - OPUS4-1731 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Niino, Hiroyuki A1 - Yabe, A. T1 - Investigation of excimer laser ablation threshold of polymers using a microphone N2 - KrF excimer laser ablation of polyethylene terephthalate (PET), polyimide (PI) and polycarbonate (PC) in air was studied by an in situ monitoring technique using a microphone. The microphone signal generated by a short acoustic pulse represented the etch rate of laser ablation depending on the laser fluence, i.e., the ablation “strength”. From a linear relationship between the microphone output voltage and the laser fluence, the single-pulse ablation thresholds were found to be 30 mJ cm-2 for PET, 37 mJ cm-2 for PI and 51 mJ cm-2 for PC (20-pulses threshold). The ablation thresholds of PET and PI were not influenced by the number of pulses per spot, while PC showed an incubation phenomenon. A microphone technique provides a simple method to determine the excimer laser ablation threshold of polymer films. KW - Laser ablation KW - Polymer KW - Treshold KW - Microphone KW - Acoustic measurement KW - Incubation PY - 2002 DO - https://doi.org/10.1016/S0169-4332(02)00418-X SN - 0169-4332 SN - 1873-5584 VL - 197-198 SP - 800 EP - 804 PB - North-Holland CY - Amsterdam AN - OPUS4-1920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Bonse, Jörn A1 - Kirner, Sabrina V. A1 - Krüger, Jörg ED - Sugioka, K. T1 - Laser-Induced Periodic Surface Structures (LIPSS) N2 - Laser-induced periodic surface structures (LIPSS) are a universal phenomenon and can be generated on almost any material by irradiation with linearly polarized radiation. This chapter reviews the current state in the field of LIPSS, which are formed in a “self-ordered” way and are often accompanying materials processing applications. LIPSS can be produced in a single-stage process and enable surface nanostructuring and, in turn, adaption of optical, mechanical, and chemical surface properties. Typically, they feature a structural size ranging from several micrometers down to less than 100 nm and show a clear correlation with the polarization direction of the light used for their generation. Various types of LIPSS are classified, relevant control parameters are identified, and their material-specific formation mechanisms are analyzed for different types of inorganic solids, i.e., metals, semiconductors, and dielectrics. Finally, technological applications featuring surface functionalization in the fields of optics, fluidics, medicine, and tribology are discussed. KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser KW - Laser ablation KW - Microstructures KW - Nanostrcutures PY - 2021 SN - 978-3-030-63646-3 (Print) SN - 978-3-030-63647-0 (Online) DO - https://doi.org/10.1007/978-3-030-63647-0_17 SP - 879 EP - 936 PB - Springer-Nature Switzerland AG CY - Cham ET - 1 AN - OPUS4-53728 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Bonse, Jörn A1 - Kirner, Sabrina V. A1 - Krüger, Jörg ED - Sugioka, K. T1 - Laser-induced periodic surface structures (LIPSS) N2 - Laser-induced periodic surface structures (LIPSS) are a universal phenomenon and can be generated on almost any material by irradiation with linearly polarized radiation. This chapter reviews the current state in the field of LIPSS, which are formed in a “self-ordered” way and are often accompanying materials processing applications. LIPSS can be produced in a single-stage process and enable surface nanostructuring and, in turn, adaption of optical, mechanical, and chemical surface properties. Typically, they feature a structural size ranging from several micrometers down to less than 100 nm and show a clear correlation with the polarization direction of the light used for their generation. Various types of LIPSS are classified, relevant control parameters are identified, and their material-specific formation mechanisms are analyzed for different types of inorganic solids, i.e., metals, semiconductors, and dielectrics. Finally, technological applications featuring surface functionalization in the fields of optics, fluidics, medicine, and tribology are discussed. KW - Laser-induced periodic surface structures (LIPSS) KW - Laser ablation KW - Femtosecond laser KW - Nanostructures KW - Microstructures PY - 2020 SN - 978-3-319-69537-2 DO - https://doi.org/10.1007/978-3-319-69537-2_17-1 SP - 1 EP - 59 PB - Springer Nature CY - Cham, Switzerland ET - 1 AN - OPUS4-51332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Bonse, Jörn A1 - Kirner, Sabrina V. A1 - Krüger, Jörg ED - Sugioka, K. T1 - Laser-induced periodic surface structures (LIPSS) N2 - Laser-induced periodic surface structures (LIPSS) are a universal phenomenon and can be generated on almost any material by irradiation with linearly polarized radiation. This chapter reviews the current state in the field of LIPSS, which are formed in a “self-ordered” way and are often accompanying materials processing applications. LIPSS can be produced in a single-stage process and enable surface nanostructuring and, in turn, adaption of optical, mechanical, and chemical surface properties. Typically, they feature a structural size ranging from several micrometers down to less than 100 nm and show a clear correlation with the polarization direction of the light used for their generation. Various types of LIPSS are classified, relevant control parameters are identified, and their material-specific formation mechanisms are analyzed for different types of inorganic solids, i.e., metals, semiconductors, and dielectrics. Finally, technological applications featuring surface functionalization in the fields of optics, fluidics, medicine, and tribology are discussed. KW - Femtosecond laser KW - Laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Microstructures KW - Nanostructures PY - 2021 SN - 978-3-319-69537-2 DO - https://doi.org/10.1007/978-3-319-69537-2_17-2 SP - 1 EP - 59 PB - Springer Nature CY - Cham, Switzerland ET - 2 AN - OPUS4-51493 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stratakis, E. A1 - Bonse, Jörn A1 - Heitz, J. A1 - Siegel, J. A1 - Tsibidis, G.D. A1 - Skoulas, E. A1 - Papadopoulos, A. A1 - Mimidis, A. A1 - Joel, A.-C. A1 - Comanns, P. A1 - Krüger, Jörg A1 - Florian, C. A1 - Fuentes-Edfuf, Y. A1 - Solis, J. A1 - Baumgartner, W. T1 - Laser engineering of biomimetic surfaces N2 - The exciting properties of micro- and nano-patterned surfaces found in natural species hide a virtually endless potential of technological ideas, opening new opportunities for innovation and exploitation in materials science and engineering. Due to the diversity of biomimetic surface functionalities, inspirations from natural surfaces are interesting for a broad range of applications in engineering, including phenomena of adhesion, friction, wear, lubrication, wetting phenomena, self-cleaning, antifouling, antibacterial phenomena, thermoregulation and optics. Lasers are increasingly proving to be promising tools for the precise and controlled structuring of materials at micro- and nano-scales. When ultrashort-pulsed lasers are used, the optimal interplay between laser and material parameters enables structuring down to the nanometer scale. Besides this, a unique aspect of laser processing technology is the possibility for material modifications at multiple (hierarchical) length scales, leading to the complex biomimetic micro- and nano-scale patterns, while adding a new dimension to structure optimization. This article reviews the current state of the art of laser processing methodologies, which are being used for the fabrication of bioinspired artificial surfaces to realize extraordinary wetting, optical, mechanical, and biological-active properties for numerous applications. The innovative aspect of laser functionalized biomimetic surfaces for a wide variety of current and future applications is particularly demonstrated and discussed. The article concludes with illustrating the wealth of arising possibilities and the number of new laser micro/nano fabrication approaches for obtaining complex high-resolution features, which prescribe a future where control of structures and subsequent functionalities are beyond our current imagination. KW - Biomimetic surfaces KW - Laser processing KW - Surface functionalization KW - Bioinspiration KW - Bionic materials PY - 2020 DO - https://doi.org/10.1016/j.mser.2020.100562 SN - 0927-796X VL - 141 SP - 100562-1 EP - 100562-47 PB - Elsevier B.V. AN - OPUS4-50927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Mezera, Marek A1 - Florian, C. A1 - Römer, G.-W. A1 - Krüger, Jörg A1 - Bonse, Jörn ED - Stoian, R. ED - Bonse, Jörn T1 - Creation of Material Functions by Nanostructuring N2 - Surface nanostructures provide the possibility to create and tailor surface functionalities mainly via controlling their topography along with other chemical and physical material properties. One of the most appealing technologies for surface functionalization via micro- and nanostructuring is based on laser processing. This can be done either via direct contour-shaping of the irradiated material using a tightly focused laser beam or in a self-ordered way that allows employing larger laser beam diameters along with areal scanning to create a variety of laser-induced periodic surface structures (LIPSS). For the latter approach, particularly ultrashort pulsed lasers have recently pushed the borders across long-lasting limitations regarding the minimum achievable feature sizes and additionally boosted up the production times. This chapter reviews the plethora of recently investigated applications of LIPSS—for example, via imposing diffractive or plasmonic structural colors, the management of liquids and surface wetting properties, biomedical and bioinspired functionalities, beneficial effects in tribology for reducing friction and wear, the manipulation of optical scattering and absorption in photovoltaics, or the modification of magnetic or superconducting surface properties in other energy applications. The footprint of the LIPSS-based technology is explored in detail regarding the current state of industrialization, including an analysis of the market and associated LIPSS production costs. KW - Laser-induced periodic surface structures, LIPSS KW - Surface functionalization KW - Nanostructures KW - Microstructures KW - Laser processing PY - 2023 SN - 978-3-031-14751-7 SN - 978-3-031-14752-4 DO - https://doi.org/10.1007/978-3-031-14752-4_23 VL - 239 SP - 827 EP - 886 PB - Springer Nature Switzerland AG CY - Cham, Switzerland AN - OPUS4-57295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwibbert, Karin A1 - Richter, Anja A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Laser-Textured Surfaces: A Way to Control Biofilm Formation? N2 - Bacterial biofilms pose serious problems in medical and industrial settings. One of the major societal challenges lies in the increasing resistance of bacteria against biocides used in antimicrobial treatments, e.g., via overabundant use in medicine, industry, and agriculture or cleaning and disinfection in private households. Hence, new efficient bacteria-repellent strategies avoiding the use of biocides are strongly desired. One promising route to achieve bacteria-repellent surfaces lies in the contactless and aseptic large-area laser-processing of technical surfaces. Tailored surface textures, enabled by different laser-processing strategies that result in topographic scales ranging from nanometers to micrometers may provide a solution to this challenge. This article presents a current state-of-the-art review of laser-surface subtractive texturing approaches for controlling the biofilm formation for different bacterial strains and in different environments. Based on specific properties of bacteria and laser-processed surfaces, the challenges of anti-microbial surface designs are discussed, and future directions will be outlined. KW - Antibacterial surfaces KW - Biofilms KW - Laser processing KW - Laser-induced periodic surface structures (LIPSS) KW - Microbial adhesions PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-588260 DO - https://doi.org/10.1002/lpor.202300753 SN - 1863-8899 SP - 1 EP - 41 PB - Wiley-VCH GmbH CY - Weinheim AN - OPUS4-58826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - The Femtosecond Pulse Laser: a New Tool for Micromachining KW - Femtosekundenlaser KW - Mikrobearbeitung PY - 1999 SN - 1054-660X SN - 1531-8494 IS - 9,1 SP - 30 EP - 40 PB - MAIK Nauka/Interperiodica Publ. CY - Moscow AN - OPUS4-712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kautek, Wolfgang A1 - Rudolph, Pascale A1 - Krüger, Jörg A1 - Rosenfeld, A. A1 - Lorenz, M. A1 - Ashkenasi, D. T1 - Morphological and mechanical investigations of bariumalumoborosilicate glass surfaces processed with 700-fs laser pulses N2 - We present surface micro-modifications of bariumalumoborosilicate glasses with a high transformation temperature near 700 °C. Laser processing of the glass substrate was realized by using ultra-short laser pulses at 800 nm. The morphological conversion of the laser-treated surfaces was characterized by scanning force microscopy and nano-indentation. A hardness increase by at least a factor of six on the laser ablation crater edge relative to illuminated non- ablated areas shows that the material in the crater walls underwent drastic morphological and mechanical changes. In this heat- and shock-affected zone, the material became more elastic as a result of increased stress. T2 - 5th International Conference on Laser Ablation ; COLA '99 CY - Göttingen, Germany DA - 1999-07-19 KW - Bariumalumoborosilicate glass surfaces PY - 1999 DO - https://doi.org/10.1007/s003390051523 SN - 0947-8396 VL - 69 IS - 7 SP - S759 EP - S761 PB - Springer CY - Berlin AN - OPUS4-775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Newesely, H. T1 - Femtosecond-pulse laser ablation of dental hydroxyapatite and single-crystalline fluoroapatite N2 - Laser microdrilling of healthy human enamel and dentine using 300 fs pulses at a wavelength of 615 nm and 3 Hz repetition rate leads to an enhanced structuring quality in comparison with nanosecond-laser results. Microcracking and damage to neighboring tissue can be reduced. Ablation threshold fluences for 100 laser pulses of 0.3 J cm-2 (human dentine), 0.6 J cm-2 (human enamel) and 0.8 J cm-2 (single crystalline fluoroapatite) could be determined. Ablation depths per pulse below 1 7m were observed. T2 - 5th International Conference on Laser Ablation ; COLA '99 CY - Göttingen, Germany DA - 1999-07-19 PY - 1999 DO - https://doi.org/10.1007/s003390051426 SN - 0947-8396 VL - 69 IS - 7 SP - S403 EP - S407 PB - Springer CY - Berlin AN - OPUS4-779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bonse, Jörn A1 - Baudach, Steffen A1 - Krüger, Jörg A1 - Kautek, Wolfgang ED - Phipps, C. T1 - Femtosecond laser micromachining of technical materials N2 - Micromachining experiments were performed with Ti:sapphire laser pulses (130 fs - 150 fs, 800 nm, approximately 10 Hz) in air. Employing the direct focusing technique, highly absorbing titanium nitride (TiN) and weakly absorbing polyimide (PI) and polymethylmethacrylate (PMMA) served as target materials. The lateral and vertical precision of the laser ablation and morphological features were characterized by scanning force (SFM), scanning electron (SEM) and optical microscopy. For TiN, incubation can be observed, i.e. the single-pulse surface damage threshold (0.26 J/cm2) is by a factor of two greater than the threshold for 100 pulses. Ablation rates below 10 nm per pulse can be achieved. The evolution of sub-wavelength ripples is presented in dependence on pulse number and laser fluence, respectively. The incubation behavior of the polymers can be described by an accumulation model as for TiN. Experiments on PI with varying focal lengths result in the same modification thresholds. Different polarization states of light (linear, circular) lead to a variation of the ablation rate and to various morphological patterns in the ablation craters (wavelength ripples, cones). Swelling of PMMA occurred at fluences below the ablation threshold. T2 - 3rd SPIE's International Conference on High-Power Laser Ablation CY - Santa Fe, NM, USA DA - 24.04.2000 KW - Ablation KW - Femtosecond pulse laser KW - Laser processing KW - Micromachining KW - Polymer KW - Titanium nitride KW - Ripples PY - 2000 SN - 0-8194-3700-X DO - https://doi.org/10.1117/12.407346 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 4065 SP - 161 EP - 172 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rudolph, Pascale A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - Mikrostrukturierung von Glas zur Erzeugung kristalliner Si-Schichten PY - 2000 IS - 12 SP - 7 EP - 36 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Lenzner, M. A1 - Sartania, S. A1 - Spielmann, C. A1 - Krausz, F. T1 - Laser micromachining of barium aluminium borosilicate glass with pulse durations between 20 fs and 3 ps N2 - Laser-micromachining of high-tech glass has been extended down to a pulse duration of 20 fs generated by a Ti sapphire laser system at a wavelength of 780 nm. A systematic electronmicroscopic study shows that, below 100 fs, an extreme precision and a substantial decrease of the ablation threshold fluence with respect to pulse laser processing with pulses in the picosecond and nanosecond range could be achieved. The technical relevance of this novel microtechnology is discussed. The morphology of the ablated areas is not determined by thermal processes, i.e. the heat affected zone. It is controlled by non-linear optical coupling effects. Multi-photon absorption becomes highly efficient below laser pulse durations of 100 fs so that light penetration is minimized and ablation cavities become smooth. At longer pulse durations, a higher light penetration due to a lower number of non-linearly absorbed photons allows mechanical relaxation processes in the glass material leading to roughening. KW - Laser micromachining KW - Subpicosecond laser ablation KW - Barium aluminium borosilicate glass PY - 1998 DO - https://doi.org/10.1016/S0169-4332(97)00763-0 SN - 0169-4332 SN - 1873-5584 IS - 127-129 SP - 892 EP - 898 PB - North-Holland CY - Amsterdam AN - OPUS4-887 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Niino, H. T1 - Biomaterial immobilization on polyurethane films by XeCl excimer laser processing N2 - Zusammenfassung The surface chemical modification of polyurethane (PU) films was performed by an UV laser-induced chemical reaction in a polysaccharide solution. This process may be applicable as hydrophilic packaging of implantable medical devices and in vivo sensors. When a PU film in contact with an aqueous alginic acid (AAC) solution was irradiated with a XeCl laser, the PU film turned hydrophilic. Contact angles of water on the film were reduced from 110° to 60°. Since light absorption of the AAC solution at 308 nm was negligibly small, reactive sites were generated solely on the PU surface. There, AAC could be immobilized by chemical bonds thus allowing for a nanometer-scaled grafting of this biomolecule. The mechanism was investigated by surface analyses with Fourier-transform infrared spectroscopy (FT-IR), dye staining, ultraviolet-visible (UV-VIS) spectroscopy, and scanning electron microscopy (SEM) techniques. A one-photon photochemical process could beidentified. PY - 2001 DO - https://doi.org/10.1007/s003390000617 SN - 0947-8396 VL - 72 IS - 1 SP - 53 EP - 57 PB - Springer CY - Berlin AN - OPUS4-926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bonse, Jörn A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Wrobel, J. M. T1 - Femtosecond pulse laser machining of InP wafers N2 - Ablation of indium phosphide wafers in air was performed with 130 fs laser pulses at a wavelength of 800 nm at a low repetition rate of 10 Hz. In order to evaluate the role of the incubation effects, the relationship between the number of laser pulses used for the ablation and the threshold fluence was studied. Particular attention was paid to the chemical composition, surface morphology and structural variations of the ablated area. T2 - 5th Laser Applications in Microelectronics and Optoelectronics Manufacturing Conference (LAMOM) CY - San José, CA, USA DA - 240.01.2000 KW - Femtosecond laser ablation KW - Indium phosphide KW - Auger electron spectroscopy PY - 2000 SN - 0-8194-3550-3 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 3933 SP - 280 EP - 287 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krüger, Jörg A1 - Bonse, Jörn A1 - Baudach, Steffen A1 - Kautek, Wolfgang A1 - Lenzner, M. A1 - Wrobel, J. M. T1 - Femtosecond-Pulse Laser Machining of Semiconducting Materials N2 - Summary form only given. Machining investigations of crystalline silicon have been performed with laser pulses at a wavelength of 780 nm in the range between 5 fs and 400 fs. Applying 100 pulses per spot, surface damage thresholds were determined by the measurement of the damage diameter. In this pulse duration regime, the threshold fluences were nearly constant. Single-pulse investigations with 5 fs pulses yielded a value of about 0.15 J cm-2 identical to the multi-pulse experiment. This is in contradiction to the behaviour of dielectrics where incubation effects alter the optical properties down to the 5 fs pulse regime. Employing laser pulses with a duration of 130 fs at a wavelength of 800 nm, single-pulse ablation thresholds of 0.23 J cm-2 and 0.16 J cm-2 were determined for Si and InP in air, respectively. The threshold fluence was calculated from the linear relation between the square of the diameters versus the logarithm of the laser fluences. T2 - CLEO/Europe 2000 ; Conference on Lasers and Electro-Optics Europe ; Conférence Européenne sur les Lasers et l'Electro-Optique ; CLEO/Europe-IQEC CY - Nice, France DA - 2000-09-10 PY - 2000 SN - 0-7803-6319-1 DO - https://doi.org/10.1109/CLEOE.2000.910410 PB - IEEE Service Center CY - Piscataway, NJ AN - OPUS4-958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kraft, S. A1 - Böttcher, Katrin A1 - Bonse, Jörn A1 - Schille, J. A1 - Löschner, U. A1 - Krüger, Jörg T1 - Unwanted X-ray emission in ultrashort pulse laser processing: From metallic to biological materials N2 - X-rays can be generated as an unwanted side effect during ultrashort pulse laser material processing of technical work pieces and even biological samples with laser intensities above 10^13 W/cm^2. First studies demonstrate the need to address this effect in industrial as well as in medical applications. This secondary hazard should be considered in work safety and risk assessment. T2 - Lasers in Manufacturing 2023 (LiM 2023) CY - Munich, Germany DA - 26.06.2023 KW - Ultrashort pulse laser processing KW - Laser-induced X-ray emission KW - Secondary hazard PY - 2023 SP - LiM 2023 - 1 EP - LiM 2023 - 6 PB - Wissenschaftliche Gesellschaft Lasertechnik und Photonik e.V. (WLT) AN - OPUS4-58358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pentzien, Simone A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Krüger, Jörg A1 - Kleber, F. A1 - Hollaus, F. A1 - Diem, M. A1 - Sablatnig, R. T1 - Can modern technologies defeat nazi censorship? KW - Laser cleaning KW - Multispectral imaging KW - Image enhancement KW - Ancient manuscripts KW - Image restoration PY - 2010 SN - 1556-4673 VL - 2 IS - 3, Article 1 SP - 1 EP - 16 PB - Association for Computing Machinery CY - New York, NY, USA AN - OPUS4-25651 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pentzien, Simone A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Krüger, Jörg A1 - Kleber, F. A1 - Hollaus, F. A1 - Diem, M. A1 - Sablatnig, R. ED - Park, J.-I. ED - Kim, J. T1 - Can Modern Technologies Defeat Nazi Censorship? N2 - Censorship of parts of written text was and is a common practice in totalitarian regimes. It is used to destroy information not approved by the political power. Recovering the censored text is of interest for historical studies of the text. This paper raises the question, whether a censored postcard from 1942 can be made legible by applying multispectral imaging in combination with laser cleaning. In the fields of art conservation (e.g. color measurements), investigation (e.g. Analysis of underdrawings in paintings), and historical document analysis, multispectral imaging techniques have been applied successfully to give visibility to information hidden to the human eye. The basic principle of laser cleaning is to transfer laser pulse energy to a contamination layer by an absorption process that leads to heating and evaporation of the layer. Partial laser cleaning of postcards is possible; dirt on the surface can be removed and the obscured pictures and writings made visible again. We applied both techniques to the postcard. The text could not be restored since the original ink seems to have suffered severe chemical damage. T2 - ACCV 2012 Workshops, 11th Asian conference on computer vision CY - Daejeon, Korea DA - 05.11.2012 KW - Laser cleaning KW - Multispectral imaging KW - Image restoration KW - Image enhancement PY - 2013 SN - 978-3-642-37483-8 SN - 0302-9743 VL - II IS - LNCS 7729 SP - 13 EP - 24 PB - Springer CY - Berlin Heidelberg AN - OPUS4-28160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kautek, Wolfgang A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Krüger, Jörg A1 - Brzezinka, Klaus-Werner T1 - Pulsed-laser deposition and boron-blending of diamond-like carbon (DLC) thin films KW - Pulslaser KW - Bor KW - Dünnfilmtechnologie KW - Dünnfilm, diamantartig PY - 1996 SN - 0169-4332 SN - 1873-5584 VL - 106 SP - 158 EP - 165 PB - North-Holland CY - Amsterdam AN - OPUS4-630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krüger, Jörg A1 - Kautek, Wolfgang ED - Dubowski, J. T1 - Femtosecond-pulse laser processing of metallic and semiconducting thin films KW - Femtosekundenpulslaser KW - Pulslaser KW - Dünnschicht, metallisch KW - Dünnschicht, halbleitend KW - Ablation PY - 1995 SN - 0-8194-1750-5 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 2403 SP - 436 EP - 447 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Rudolph, Pascale A1 - Krüger, Jörg A1 - Baudach, Steffen A1 - Kautek, Wolfgang T1 - Femtosecond pulse laser processing of TiN on silicon N2 - Ultrashort pulse laser microstructuring (pulse duration 130 fs, wavelength 800 nm, repetition rate 2 Hz) of titanium nitride (TiN) films on silicon substrates was performed in air using the direct focusing technique. The lateral and vertical precision of laser ablation was evaluated. The TiN ablation threshold changed with the number of pulses applied to the surface due to an incubation effect. An ablation depth per pulse below the penetration depth of light was observed. Columnar structures were formed in the silicon substrate after drilling through the TiN layer. KW - Femtosecond laser ablation KW - Titanium nitride KW - Silicon KW - Optical properties PY - 2000 DO - https://doi.org/10.1016/S0169-4332(99)00481-X SN - 0169-4332 SN - 1873-5584 VL - 154-155 SP - 659 EP - 663 PB - North-Holland CY - Amsterdam AN - OPUS4-802 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baudach, Steffen A1 - Bonse, Jörn A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - Ultrashort pulse laser ablation of polycarbonate and polymethylmethacrylate N2 - Ablation experiments with ultrashort laser pulses (pulse duration 150 fs, wavelength 800 nm) on polymers (PC, PMMA) relevant for biomedical technology have been performed in air. The lateral and vertical machining precision was evaluated by optical, atomic force and scanning electron microscopy. The ablation threshold reaches values in the range of 0.5–2.5 J/cm2 and depends significantly on the number of laser pulses applied to the same spot. The hole diameters are influenced by the laser fluence and the number of laser pulses. The relation between the ablation threshold and the number of laser pulses applied to the same spot is described in accordance with an incubation model. KW - Femtosecond laser ablation KW - Polymer KW - Polycarbonate KW - Polymethylmethacrylate PY - 2000 DO - https://doi.org/10.1016/S0169-4332(99)00474-2 SN - 0169-4332 SN - 1873-5584 VL - 154-155 SP - 555 EP - 560 PB - North-Holland CY - Amsterdam AN - OPUS4-803 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Lenzner, M. A1 - Krausz, F. T1 - Precision laser ablation of dielectrics in the 10-fs regime N2 - Zusammenfassung Laser pulses in the 10-fs domain provide a quality of micromachining of fused silica and borosilicate glass that is unobtainable with longer pulses in the range of several 100 femtoseconds up to picoseconds. The shortening of the pulses reduces the statistical behavior of the material removal and the ablation process thus attains a more deterministic and reproducible character. The improved reproducibility of ablation is accompanied by significantly smoother morphology. This offers the potential for lateral and vertical machining precision of the order of 100 nm and 10 nm, respectively. KW - Laser ablation PY - 1999 DO - https://doi.org/10.1007/s003390050906 SN - 0947-8396 VL - 68 IS - 3 SP - 369 EP - 371 PB - Springer CY - Berlin AN - OPUS4-825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Krivenko, A.G. A1 - Benderskii, V.A. T1 - Gigantic Hydrogen-Ion Discharge Currents Initiated by a Subpicosecond Laser PY - 1998 SN - 0038-5387 SN - 1023-1935 VL - 34 IS - 10 SP - 1068 EP - 1075 PB - MAIK Nauka/Interperiodica Publ. CY - Moscow AN - OPUS4-826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Lenzner, M. A1 - Krausz, F. T1 - Incubation of laser ablation in fused silica with 5-fs pulses N2 - Zusammenfassung The threshold fluences for laser-induced damage of fused silica with single 5-fs pulses from a Ti:sapphire laser system were determined by extrapolating the ablated volume to zero. These thresholds are about 4 times as high as the values previously obtained from multi-shot experiments. This result is interpreted in terms of an irreversible modification of the original material below the single-shot threshold (incubation). KW - Laser PY - 1999 DO - https://doi.org/10.1007/s003390051034 SN - 0947-8396 VL - 69 IS - 4 SP - 465 EP - 466 PB - Springer CY - Berlin AN - OPUS4-799 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Jörg A1 - Kautek, Wolfgang A1 - Lenzner, M. A1 - Krausz, F. T1 - Photoablation with sub-10 fs laser pulses N2 - Ablation experiments in several glasses with single and multishot irradiation by laser pulses in the 10-fs pulse duration domain are presented; physical and technological implications are discussed. We demonstrate that these short pulses offer the potential for lateral and vertical machining precision of the order of 100 nm. KW - Ablation KW - Laser pulses KW - Femtosecond pulses PY - 2000 DO - https://doi.org/10.1016/S0169-4332(99)00432-8 SN - 0169-4332 SN - 1873-5584 VL - 154-155 SP - 11 EP - 16 PB - North-Holland CY - Amsterdam AN - OPUS4-800 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rudolph, Pascale A1 - Bonse, Jörn A1 - Krüger, Jörg A1 - Kautek, Wolfgang T1 - Femtosecond- and nanosecond-pulse laser ablation of bariumalumoborosilicate glass N2 - Laser ablation with femtosecond pulses (130 fs, wavelength 800 nm, repetition rate 2 Hz) was compared with nanosecond-pulse ablation (10 ns, wavelength 266 nm, repetition rate 2.5 Hz) of bariumalumoborosilicate glass in air using the direct focusing technique. Different ablation thresholds and heat-affected zones were observed. The lateral and vertical machining precision was evaluated. Single nanosecond laser pulses in the far UV resulted in a bubble or a circular hole in the centre of the illuminated spot, depending on the applied fluence. The ablation behaviour in the case of near-IR femtosecond pulses contrasted to this. Bubble formation was not detected. It needed repeated pulses at the same spot to modify the surface until material removal could be observed (incubation). Cavity dimensions of less than the beam diameter were achieved in this case. T2 - 5th International Conference on Laser Ablation ; COLA '99 CY - Göttingen, Germany DA - 1998-07-19 KW - Laser ablation KW - Bariumalumoborosilicate glass PY - 1999 DO - https://doi.org/10.1007/s003390051524 SN - 0947-8396 VL - 69 IS - 7 SP - S763 EP - S766 PB - Springer CY - Berlin AN - OPUS4-801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wolfs, Rob A1 - Versteegen, Jelle A1 - Santhanam, Manu A1 - Bhattacherjee, Shantanu A1 - Bos, Freek A1 - Robens-Radermacher, Annika A1 - Muthukrishnan, Shravan A1 - Menna, Costantino A1 - Ozturk, Onur A1 - Ozyurt, Nilufer A1 - Roupec, Josef A1 - Richter, Christiane A1 - Jungwirth, Jörg A1 - Miranda, Luiza A1 - Ammann, Rebecca A1 - Caron, Jean-François A1 - de Bono, Victor A1 - Monte, Renate A1 - Navarrete, Iván A1 - Eugenin, Claudia A1 - Lombois‑Burger, Hélène A1 - Baz, Bilal A1 - Sinka, Maris A1 - Sapata, Alise A1 - Harbouz, Ilhame A1 - Zhang, Yamei A1 - Jia, Zijian A1 - Kruger, Jacques A1 - Mostert, Jean‑Pierre A1 - Šter, Katarina A1 - Šajna, Aljoša A1 - Kaci, Abdelhak A1 - Rahal, Said A1 - Snguanyat, Chalermwut A1 - Arunothayan, Arun A1 - Zhao, Zengfeng A1 - Mai, Inka A1 - Rasehorn, Inken Jette A1 - Böhler, David A1 - Freund, Niklas A1 - Lowke, Dirk A1 - Neef, Tobias A1 - Taubert, Markus A1 - Auer, Daniel A1 - Hechtl, C. Maximilian A1 - Dahlenburg, Maximilian A1 - Esposito, Laura A1 - Buswell, Richard A1 - Kolawole, John A1 - Isa, Muhammad Nura A1 - Liu, Xingzi A1 - Wang, Zhendi A1 - Subramaniam, Kolluru A1 - Mechtcherine, Viktor T1 - Mechanical properties of 3D printed concrete: a RILEM TC 304-ADC interlaboratory study — flexural and tensile strength N2 - This paper discusses the flexural and tensile strength properties of 3D printed concrete, based on the results of a RILEM TC 304-ADC interlaboratory study on mechanical properties. These properties are determined using different testing techniques, including 3- and 4-point flexural tests, splitting tests, and uniaxial tension tests, on specimens extracted from large 3D printed elements in accordance with a prescribed study plan. The relationship between compressive and flexural or tensile strengths, cast or printed samples, different types of tests, and different loading orientations, are analysed to understand the influence of 3D printing. As expected, the strength can reduce significantly when the main tensile stress is acting perpendicular to the interface between layers. The role of deviations from the standard study procedure, in terms of the time interval between the placing of subsequent layers, or the adoption of a different curing strategy, are also assessed. While the increased time interval significantly impacts the strength in the critical direction, the use of variable curing conditions does not seem to have a clear-cut effect on the strength ratios of the printed to cast specimens. Additionally, the paper looks at the variability in the results for the printed specimens, in order to emphasize the need for multiple replicates for obtaining a proper result. An extensive insight into the aspects affecting the variability is presented in the paper. Finally, with the limited dataset available for specimens tested at a larger scale, it is difficult to arrive at a clear understanding of the role of specimen size (i.e., greater number of layers). KW - 3D concrete printing KW - Digital fabrication KW - Flexural strength KW - Tensile strength KW - Interlayer bond strength PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634655 DO - https://doi.org/10.1617/s11527-025-02687-w SN - 1871-6873 VL - 58 IS - 5 SP - 1 EP - 33 PB - Springer Nature AN - OPUS4-63465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mechtcherine, Viktor A1 - Muthukrishnan, Shravan A1 - Robens-Radermacher, Annika A1 - Wolfs, Rob A1 - Versteege, Jelle A1 - Menna, Costantino A1 - Ozturk, Onur A1 - Ozyurt, Nilufer A1 - Roupec, Josef A1 - Richter, Christiane A1 - Jungwirth, Jörg A1 - Miranda, Luiza A1 - Ammann, Rebecca A1 - Caron, Jean‑François A1 - de Bono, Victor A1 - Monte, Renate A1 - Navarrete, Iván A1 - Eugenin, Claudia A1 - Lombois‑Burger, Hélène A1 - Baz, Bilal A1 - Sinka, Maris A1 - Sapata, Alise A1 - Harbouz, Ilhame A1 - Zhang, Yamei A1 - Jia, Zijian A1 - Kruger, Jacques A1 - Mostert, Jean‑Pierre A1 - Štefančič, Mateja A1 - Hanžič, Lucija A1 - Kaci, Abdelhak A1 - Rahal, Said A1 - Santhanam, Manu A1 - Bhattacherjee, Shantanu A1 - Snguanyat, Chalermwut A1 - Arunothayan, Arun A1 - Zhao, Zengfeng A1 - Mai, Inka A1 - Rasehorn, Inken Jette A1 - Böhler, David A1 - Freund, Niklas A1 - Lowke, Dirk A1 - Neef, Tobias A1 - Taubert, Markus A1 - Auer, Daniel A1 - Hechtl, C. Maximilian A1 - Dahlenburg, Maximilian A1 - Esposito, Laura A1 - Buswell, Richard A1 - Kolawole, John A1 - Isa, Muhammad Nura A1 - Liu, Xingzi A1 - Wang, Zhendi A1 - Subramaniam, Kolluru A1 - Bos, Freek T1 - Mechanical properties of 3D printed concrete: a RILEM 304-ADC interlaboratory study – compressive strength and modulus of elasticity N2 - Traditional construction techniques, such as in-situ casting and pre-cast concrete methods, have well-established testing protocols for assessing compressive strength and modulus of elasticity, including specific procedures for sample preparation and curing. In contrast, 3D concrete printing currently lacks standardized testing protocols, potentially contributing to the inconsistent results reported in previous studies. To address this issue, RILEM TC 304-ADC initiated a comprehensive interlaboratory study on the mechanical properties of 3D printed concrete. This study involves 30 laboratories worldwide, contributing 34 sets of data, with some laboratories testing more than one mix design. The compressive strength and modulus of elasticity were determined under three distinct conditions: Default, where each laboratory printed according to their standard procedure followed by water bath curing; Deviation 1, which involved creating a cold joint by increasing the time interval between printing layers; and Deviation 2, where the standard printing process was used, but the specimens were cured under conditions different from water bath. Some tests were conducted at two different scales based on specimen size—“mortar-scale” and “concrete-scale”—to investigate the size effect on compressive strength. Since the mix design remained identical for both scales, the only variable was the specimen size. This paper reports on the findings from the interlaboratory study, followed by a detailed investigation into the influencing parameters such as extraction location, cold joints, number of interlayers, and curing conditions on the mechanical properties of the printed concrete. As this study includes results from laboratories worldwide, its contribution to the development of relevant standardized testing protocols is critical. KW - Additive manufacturing KW - Digital fabrication KW - Hardened concrete KW - Compressive strength KW - Young's modulus PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634672 DO - https://doi.org/10.1617/s11527-025-02688-9 SN - 1871-6873 VL - 58 IS - 5 SP - 1 EP - 30 PB - Springer Nature AN - OPUS4-63467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Voss, Heike A1 - Zahedi-Azad, Setareh A1 - Ernst, Owen C. A1 - Lucaßen, Jan A1 - Mann, Guido A1 - Bonse, Jörn A1 - Boeck, Torsten A1 - Martin, Jens A1 - Schmid, Martina A1 - Krüger, Jörg T1 - Chemical vapor deposition of indium precursors for solar microabsorbers using continuous laser radiation BT - A, Materials science & processing N2 - Localized deposition of indium on an amorphous glass surface covered with a thin molybdenum layer is demonstrated utilizing laser-assisted chemical vapor deposition. A continuous-wave laser causes a temperature rise on the molybdenum layer resulting in the selective aggregation of liquid and ultimately crystalline structures of indium. The formation sites of the indium are determined by the decomposition of gaseous trimethylindium. The deposited indium islands can serve as precursors and could be further processed into compound semiconductors like CuInSe2 for micro-concentrator solar cells. The experimental investigations were supported by theoretical simulations of the laser heating process to calculate the local temperature distribution on the surface of the molybdenum-covered glass substrate. KW - Laser-assisted Chemical Vapor Deposition KW - CW Laser KW - Indium Islands KW - Micro-concentrator Solar Cell PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641069 DO - https://doi.org/10.1007/s00339-025-08895-z SN - 0947-8396 VL - 131 SP - 1 EP - 10 PB - Springer CY - Berlin ; Heidelberg [u.a.] AN - OPUS4-64106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böttcher, Katrin A1 - Kraft, Sebastian A1 - Weise, Matthias A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Publisher correction: X-ray emission during ultrafast laser grooving N2 - This is a corrigendum to the original article "X-ray emission during ultrafast laser grooving" that was published in the journal "Applied Physics A", vol. 131 (2025), article 651 (doi 10.1007/s00339-025-08728-z). PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-648868 DO - https://doi.org/10.1007/s00339-025-08882-4 SN - 0947-8396 VL - 131 IS - 11 SP - 1 PB - Springer CY - Berlin AN - OPUS4-64886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böttcher, Katrin A1 - Kraft, Sebastian A1 - Weise, Matthias A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - X-ray emission during ultrafast laser grooving N2 - Ultrashort pulse lasers offer the possibility to process materials with minimal heat input and high precision. However, the X-ray emission at high laser peak intensities represents an undesirable side effect. A laser system (1030 nm wavelength, 40 W maximum average laser power, 925 fs pulse duration, 100 μJ maximum pulse energy, 400 kHz pulse repetition frequency) was used to analyze the X-ray skin dose rates for applied peak intensities between 9.2 × 10^12 W/cm^2 and 1.3 × 10^14 W/cm^2 for mild steel, stainless steel and tungsten during groove processing. The lowest laser peak intensity at which X-ray emission could be measured was 9.2 × 10^12 W/cm^2 for processing of stainless steel. The X-ray emission showed a characteristic evolution in dependence on the number of overscans at the same line positions. For low peak intensities, a measurable X-ray emission only begins after a few passes. The number of scans to reach the maximum dose rate increases with lower laser peak intensity. Analysis of the evolving surface topography by white light interference microscopy in connection with ray-tracing simulations led to the interpretation that the increase in X-ray emission is due to the local intensity redistribution by multiple reflection within the laser-generated grooves which is promoted by a particular choice of the linear laser polarization. KW - Ultrashort pulsed laser KW - Laser-induced X-rays KW - X-ray hazard KW - X-ray emission PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639483 DO - https://doi.org/10.1007/s00339-025-08728-z SN - 1432-0630 VL - 131 IS - 8 SP - 1 EP - 12 PB - Springer CY - Berlin AN - OPUS4-63948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Symietz, Christian A1 - Lehmann, Erhard A1 - Gildenhaar, Renate A1 - Hackbarth, Andreas A1 - Berger, Georg A1 - Krüger, Jörg T1 - Mechanical stability of Ti6Al4V implant material after femtosecond laser irradiation N2 - The surface of a titanium alloy (Ti6Al4V) implant material was covered with a bioactive calcium alkali phosphate ceramic with the aim to accelerate the healing and to form a stronger bond to living bone tissue. To fix the ceramic powder we used a femtosecond laser, which causes a thin surface melting of the metal. It is a requirement to prove that the laser irradiation would not reduce the lifetime of implants. Here we present the results of mechanical stability tests, determined by the rotating bending fatigue strength of sample rods. After describing the sample surfaces and their modifications caused by the laser treatment we give evidence for an unchanged mechanical stability. This applies not only to the ceramic fixation but also to a comparatively strong laser ablation. KW - Aluminium alloys KW - Bending strength KW - Bioceramics KW - Bone KW - Calcium compounds KW - Fatigue KW - Fatigue testing KW - High-speed optical techniques KW - Laser ablation KW - Melting KW - Orthopaedics KW - Prosthetics KW - Rods (structures) KW - Surface treatment KW - Titanium alloys KW - Vanadium alloys PY - 2012 DO - https://doi.org/10.1063/1.4737576 SN - 0021-8979 SN - 1089-7550 VL - 112 IS - 2 SP - 1 EP - 5 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-26200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Bachelier, G. A1 - Wiggins, S. M. A1 - Siegel, J. A1 - Solis, J. A1 - Krüger, Jörg A1 - Sturm, Heinz T1 - Femtosecond laser ablation of indium phosphide in air: dynamical, structural and morphological evolution N2 - The irradiation of single-crystalline indium phosphide (c-InP) by Ti:sapphire femtosecond laser pulses (130 fs, 800 nm) in air is studied by means of in-situ time resolved reflectivity measurements [fs-time-resolved microscopy (100 fs-10 ns) and point probing analysis (ns - µs)] and by complementary ex-situ surface analytical methods (Micro Raman Spectroscopy, Scanning Force, and Optical Microscopy). The dynamics of melting, ablation, and optical breakdown as well as structural changes resulting from rapid solidification are investigated in detail. Different laser-induced surface morphologies are characterized and discussed on the basis of recent ablation and optical breakdown models. KW - Femtosecond laser ablation KW - Optical breakdown KW - Time-resolved measurements KW - Semiconductor KW - Indium phosphide PY - 2010 SN - 1454-4164 VL - 12 IS - 3 SP - 421 EP - 426 PB - INOE & INFM CY - Bucharest AN - OPUS4-21082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kirner, Sabrina A1 - Wirth, Thomas A1 - Sturm, Heinz A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Nanometer-resolved chemical analyses of femtosecond laser-induced periodic surface structures on titanium N2 - The chemical characteristics of two different types of laser-induced periodic surface structures (LIPSS), so-called high and low spatial frequency LIPSS (HSFL and LSFL), formed upon irradiation of titanium surfaces by multiple femtosecond laser pulses in air (30 fs, 790 nm, 1 kHz), are analyzed by various optical and electron beam based surface analytical techniques, including micro-Raman spectroscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy, and Auger electron spectroscopy. The latter method was employed in a high-resolution mode being capable of spatially resolving even the smallest HSFL structures featuring spatial periods below 100 nm. In combination with an ion sputtering technique, depths-resolved chemical information of superficial oxidation processes was obtained, revealing characteristic differences between the two different types of LIPSS. Our results indicate that a few tens of nanometer shallow HSFL are formed on top of a ∼150 nm thick graded superficial oxide layer without sharp interfaces, consisting of amorphous TiO2 and partially crystallized Ti2O3. The larger LSFL structures with periods close to the irradiation wavelength originate from the laser-interaction with metallic titanium. They are covered by a ∼200 nm thick amorphous oxide layer, which consists mainly of TiO2 (at the surface) and other titanium oxide species of lower oxidation states underneath. KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser KW - Oxidation KW - Titanium KW - Auger electron spectroscopy PY - 2017 DO - https://doi.org/10.1063/1.4993128 SN - 0021-8979 VL - 122 IS - 10 SP - 104901, 1 EP - 9 PB - AIP Publishing CY - Melville, NY, USA AN - OPUS4-41905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kirner, Sabrina V. A1 - Slachciak, Nadine A1 - Elert, Anna Maria A1 - Griepentrog, Michael A1 - Fischer, Daniel A1 - Hertwig, Andreas A1 - Sahre, Mario A1 - Dörfel, Ilona A1 - Sturm, Heinz A1 - Pentzien, Simone A1 - Koter, Robert A1 - Spaltmann, Dirk A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Tribological performance of titanium samples oxidized by fs-laser radiation, thermal heating, or electrochemical anodization N2 - Commercial grade-1 titanium samples (Ti, 99.6%) were treated using three alternative methods, (i) femtosecond laser processing, (ii) thermal heat treatment, and (iii) electrochemical anodization, respectively, resulting in the formation of differently conditioned superficial titanium oxide layers. The laser processing (i) was carried out by a Ti:sapphire laser (pulse duration 30 fs, central wavelength 790 nm, pulse repetition rate 1 kHz) in a regime of generating laser-induced periodic surface structures (LIPSS). The experimental conditions (laser fluence, spatial spot overlap) were optimized in a sample-scanning setup for the processing of several square-millimeters large surface areas covered homogeneously by these nanostructures. The differently oxidized titanium surfaces were characterized by optical microscopy, micro Raman spectroscopy, variable angle spectroscopic ellipsometry, and instrumented indentation testing. The tribological performance was characterized in the regime of mixed friction by reciprocating sliding tests against a sphere of hardened steel in fully formulated engine oil as lubricant. The specific tribological performance of the differently treated surfaces is discussed with respect to possible physical and chemical mechanisms. KW - Femtosecond laser KW - Titanium KW - Oxidation KW - Friction PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-445609 DO - https://doi.org/10.1007/s00339-018-1745-8 SN - 0947-8396 SN - 1432-0630 VL - 124 IS - 4 SP - 326, 1 EP - 10 PB - Springer-Verlag AN - OPUS4-44560 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mann, Guido A1 - Zoheidi, M. A1 - Krüger, Jörg T1 - Hochleistungsfasern am Limit - Laserinduzierte Zerstörung als Einsatzgrenze bei Lichtwellenleitern N2 - Aufgrund der steigenden Anforderungen an Fasern für Hochleistungsanwendungen hat die Business Unit Fiber Optics der Leoni Gruppe gemeinsam mit der BAM Bundesanstalt für Materialforschung und -prüfung die Herausforderung angenommen, erstmalig die Zerstörschwellen eigener “large core” Spezialfasern zu untersuchen. KW - Laserinduzierte Zerstörschwelle KW - Optische Multimodefaser KW - Lichtwellenleiter KW - Nanosekundenlaser PY - 2012 UR - http://www.leoni-fiber-optics.com/fileadmin/bu/fo/news/pdf/fachpresse/I-PDF_LP110166_leoni_LP4-12_kleiner_.pdf SN - 1610-3521 VL - 4 SP - 18 EP - 21 PB - Hanser CY - München AN - OPUS4-26424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -