TY - JOUR A1 - Ma, S. A1 - Xiao, Y. A1 - Zhou, F. A1 - Schartel, Bernhard A1 - Chan, Yin Yam A1 - Korobeinichev, O. P. A1 - Trubachev, S. A. A1 - Hu, W. A1 - Ma, C. A1 - Hu, Y. T1 - Effects of novel phosphorus-nitrogen-containing DOPO derivative salts on mechanical properties, thermal stability and flame retardancy of flexible polyurethane foam N2 - In this work, a series of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative salts containing phosphorus and nitrogen were synthesized, and their effects on mechanical properties, thermal stability and flame retardancy of flexible polyurethane foam (FPUF) were investigated. Studies have shown that the addition of DOPO derivatives will increase the tensile strength, compression set, and compression hardness of FPUF, but it will lead to a decrease in elongation at break. Thermogravimetric analysis showed that the initial decomposition temperature of FPUF containing DOPO derivatives was reduecd, but the char reside was significantly improved. A series of combustion tests indicated that the addition of DOPO derivative salts can improve the flame retardancy of FPUF, of which 10-hydroxy-9,10-dihydro-9-oxa-10 phosphaphenanthrene-10-oxide dicyandiamide salt (D-DICY) exhibited the best flame retardancy. When the load of D-DICY was 20 phr, the limiting oxygen index (LOI) of foam reached 24.5%, and the peak heat release rate and total heat release were decreased by 55.7% and 52.9%, respectively. Furthermore, based on the analysis of the gas phase combustion products and the char residue of the condensed phase, the possible flame retardant mechanism was proposed. KW - Flexible polyurethane foam KW - DOPO derivative salts KW - Mechanical properties KW - Thermal stability KW - Flame retardancy PY - 2020 DO - https://doi.org/10.1016/j.polymdegradstab.2020.109160 SN - 0141-3910 VL - 177 SP - 109160 PB - Elsevier Ltd. AN - OPUS4-50740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adwani, D. A1 - Pipintakos, G. A1 - Mirwald, J. A1 - Wang, Y. A1 - Hajj, R. A1 - Guo, M. A1 - Liang, M. A1 - Jing, R. A1 - Varveri, A. A1 - Zhang, Y. A1 - Pei, K. A1 - Xu, X. A1 - Leng, Z. A1 - Li, D. A1 - Villamil, W. A1 - Caro, S. A1 - Chailleux, E. A1 - Cantot, J. A1 - Weigel, Sandra A1 - Škulteckė, J. A1 - Tarsi, G. A1 - Margaritis, A. A1 - Wang, H. A1 - Hu, Y. A1 - Airey, G. A1 - Sreeram, A. A1 - Bhasin, A. T1 - Examining the efficacy of promising antioxidants to mitigate asphalt binder oxidation: Insights from a worldwide interlaboratory investigation N2 - Oxidative aging induces significant stiffening of asphalt binders that leads to a pronounced reduction in the overall durability of asphalt pavements. The strategic implementation of antioxidant additives provides a potential solution to alleviate this issue. This work presents results from the second phase of the global consortium for antioxidants research aimed at investigating the effectiveness of potential antioxidants in increasing the durability of asphalt binders. Sixteen laboratories around the world participated in this effort and a total of 28 binders from diverse geographical regions were tested. Two promising antioxidants, namely zinc diethyldithiocarbamate (ZDC) and kraft lignin were evaluated in this phase and blended with the binders at specific proportions. Subsequently, a comprehensive investigation was conducted to assess rheological characteristics and chemical properties of the various blends, utilising Dynamic Shear Rheometer (DSR) measurements and Fourier Transform Infrared (FTIR) Spectroscopy. The findings indicate that additives such as ZDC hold considerable promise as an effective antioxidant, particularly when considering a wide diversity of binders. In general, its incorporation does not compromise the rutting performance of the binders and significantly improves fatigue performance. Therefore, research efforts should be focused on exploring additional facets to assess its practical applicability in field. KW - Asphalt oxidation KW - Binder aging KW - Antioxidant additives KW - Binder rheology KW - Binder chemistry KW - Bitumen und bitumenhaltige Bindemittel KW - FTIR-Spektroskopie KW - Anwendungsmöglichkeiten KW - Vergleichsuntersuchung KW - Arbeitsanleitung KW - Präzision PY - 2024 DO - https://doi.org/10.1080/10298436.2024.2332363 SN - 1477-268X VL - 25 IS - 1 SP - 1 EP - 15 PB - Taylor & Francis CY - London AN - OPUS4-59957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pialat, A. A1 - Kitos, A. A1 - Witkowski, Tomasz A1 - Cook, C. A1 - Wang, S. A1 - Hu, A. A1 - Murugesu, M. T1 - Achieving short ignition delay and high specific impulse with cyanoborohydride based hypergolic ionic liquids N2 - The efficient design of hypergolic-ionic-liquid (HIL) fuels with attractive features, (e.g., short ignition delay and high specific impulse) can be achieved by fine-tuning the molecular organization comprising both cations with appropriate alkyl chains and cyanoborohydride-based hydrogen-rich anions. Attractive features of the presented derivatives were attained by combining cations with various substituents (substituted 1H-1,2,4-triazol-4-ium, pyrrolidinium, ammonium and pyridinium cations) and the cyanoborohydride anion. All shown HILs display high thermal stabilities with thermal decomposition temperatures over 154 °C and possess higher densities (from 0.82 to 1.02 g cm−3) compared to the unsymmetrical dimethylhydrazine (UDMH, 0.793 g cm−3). The hypergolic ignition behavior of the propellant combination was evaluated by a drop test setup using white fuming nitric acid (WFNA) as an oxidizer and recorded using a high-speed camera. All compounds feature ignition delay times (ID) under 50 ms, while the 1-hexyl-1-methylpyrrolidin-1-ium cyanotrihydroborate congener (17) exhibited the shortest ID time (5 ms), which is comparable to the ID time of UDMH (4.8 ms with WFNA as an oxidizer). In addition, these HILs exhibit higher heats of formation (187.6 to 392.6 kJ mol−1), heats of combustion (34.39 to 47.15 kJ g−1) and specific impulse (176 to 205 s) compared to UDMH. KW - Hypergolic ionic liquids PY - 2022 DO - https://doi.org/10.1039/D2NJ03372K SN - 1144-0546 SP - 1 EP - 9 PB - RSC CY - Cambridge AN - OPUS4-56147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Leach, R.K. A1 - Boyd, R. A1 - Burke, T. A1 - Danzebrink, H.-U. A1 - Dirscherl, K. A1 - Dziomba, T. A1 - Gee, M. A1 - Koenders, L. A1 - Morazzani, V. A1 - Pidduck, A. A1 - Roy, D. A1 - Unger, Wolfgang A1 - Yacoot, A. T1 - The European nanometrology landscape N2 - This review paper summarizes the European nanometrology landscape from a technical perspective. Dimensional and chemical nanometrology are discussed first as they underpin many of the developments in other areas of nanometrology. Applications for the measurement of thin film parameters are followed by two of the most widely relevant families of functional properties: measurement of mechanical and electrical properties at the nanoscale. Nanostructured materials and surfaces, which are seen as key materials areas having specific metrology challenges, are covered next. The final section describes biological nanometrology, which is perhaps the most interdisciplinary applications area, and presents unique challenges. Within each area, a review is provided of current status, the capabilities and limitations of current techniques and instruments, and future directions being driven by emerging industrial measurement requirements. Issues of traceability, standardization, national and international programmes, regulation and skills development will be discussed in a future paper. KW - Nanotechnology KW - Metrology KW - Chemistry KW - Surface analysis PY - 2011 DO - https://doi.org/10.1088/0957-4484/22/6/062001 SN - 0957-4484 SN - 1361-6528 VL - 22 IS - 6 SP - 062001-1 - 062001-15 PB - IOP Publishing Ltd. CY - Bristol AN - OPUS4-23259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Becker, S. A1 - Beckmann, Jörg A1 - Braun, M.-T. A1 - Cojocari, O. A1 - Feige, V. A1 - Fischer, B. A1 - Friederich, F. A1 - Globisch, B. A1 - Hechtfischer, G. A1 - Hens, K. A1 - Hübers, H.-W. A1 - Jelonnek, J. A1 - Jonuscheit, J. A1 - Keil, A. A1 - Kleine-Ostmann, T. A1 - Marquardt, E. A1 - Mayr, M. A1 - Nickel, H.-U. A1 - Nüßler, D. A1 - Peichl, M. A1 - Peters, O. A1 - Schür, J. A1 - Sprenger, T. A1 - Steiger, A. A1 - van Frank, S. A1 - Vieweg, N. A1 - Wilk, R. ED - Jonuscheit, J. ED - Marquardt, E. T1 - Terahertzsysteme und Anwendungsfelder N2 - Der Frequenzbereich der Terahertzwellen liegt im elektromagnetischen Spektrum zwischen den Mikrowellen und dem infraroten Licht – also etwa im Bereich von 0,1 bis 10 Terahertz (THz). Der VDI-Statusreport „Terahertzsysteme und Anwendungen“ stellt die unterschiedlichen Konzepte für Terahertzsysteme vor und zeigt Anwendungsbeispiele, bei denen die Terahertztechnik erfolgreich eingesetzt wird. Umfangreiche Literaturangaben ermöglichen eine intensivere Beschäftigung mit allen Themen des VDI-Statusreports. KW - Terahertzsysteme PY - 2020 UR - https://www.vdi.de/ueber-uns/presse/publikationen/details/terahertzsysteme-und-anwendungsfelder SP - 1 EP - 44 PB - Verein Deutscher Ingenieure (VDI) CY - Düsseldorf AN - OPUS4-50556 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Risinggård, H. K. A1 - Cooil, S. A1 - Mazzola, F. A1 - Hu, D. A1 - Kjaervik, Marit A1 - Østli, E. R. A1 - Patil, N. A1 - Preobrajenski, A. A1 - Ewans, A. D. A1 - Breiby, D. W. A1 - Trinh, T. T. A1 - Wells, J. W. T1 - Degradation of the chemotherapy drug 5-fluorouracil on medical-grade silver surfaces N2 - The degradation of the chemotherapy drug 5-fluorouracil by a non-pristine metal surfaces is studied.Using density functional theory, X-ray photoelectron spectroscopy and X-ray absorption spectroscopy we show that the drug is entirely degraded by medical-grade silver surfaces, already at body temperature,and that all of the fluorine has left the molecule, presumably as HF. Remarkably, this degradation is even more severe than that reported previously for 5-fluorouracil on a pristine monocrystalline silver surface(in which case 80% of the drug reacted at body temperature) [1]. We conclude that the observed reaction is due to a reaction pathway, driven by H to F attraction between molecules on the surface, which results in the direct formation of HF; a pathway which is favoured when competing pathways involving reactive Ag surface sites are made unavailable by environmental contamination. Our measurements indicate that realistically cleaned, non-pristine silver alloys, which are typically used in medical applications, can result in severe degradation of 5-fluorouracil, with the release of HF – a finding which may have important implications for the handling of chemotherapy drugs. KW - Surface science KW - Chemotherapy KW - DFT KW - Photoemission KW - Fluorouracil KW - Silver PY - 2018 DO - https://doi.org/10.1016/j.apsusc.2017.11.221 SN - 0169-4332 VL - 435 SP - 1213 EP - 1219 PB - Elsevier CY - Amsterdam, The Netherlands AN - OPUS4-43450 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Beck, M. A1 - Becker, S. A1 - Beckmann, Jörg A1 - Cojocari, O. A1 - Feige, V. A1 - Fischer, B. A1 - Friederich, F. A1 - Globisch, B. A1 - Haupt, H. A1 - Hechtfischer, G. A1 - Hens, K. A1 - Hübers, H.-W. A1 - Jelonnek, J. A1 - Jonuscheit, J. A1 - Keil, A. A1 - Kleine-Ostmann, T. A1 - Nickel, H.-U. A1 - Peichl, M. A1 - Peters, O. A1 - Sprenger, T. A1 - Steiger, A. A1 - van Frank, S. A1 - Vieweg, N. A1 - Werner, M. A1 - Wilk, R. T1 - Terahertzsysteme - Anwendungsfelder und Systeme N2 - Die nicht ionisierende elektromagnetische Strahlung im Bereich von Terahertz-Frequenzen ermöglicht berührungslose und zerstörungsfreie Mess- und Prüftechnik in zahlreichen Bereichen. Nach ersten Anwendungen in der Astronomie und der Atmosphärenforschung wurden in letzter Zeit Anwendungsfelder in der Sicherheitstechnik, der Medizintechnik, der Nachrichtentechnik und der zerstörungsfreien Prozess- und Qualitätskontrolle erschlossen. Dielektrische Materialien wie Kunststoffe und Keramiken können von Terahertz-Wellen durchdrungen werden. Das ermöglicht Untersuchungen des Objektinneren ohne spezielle Schutzmaßnahmen, wie sie z.B. beim Röntgen notwendig sind. Die Richtlinie erleichtert die Verständigung zwischen Nutzern, Herstellern und dem Vertrieb von Terahertz-Systemen. In der Richtlinie werden bekannte Einsatzgebiete sowie die eingesetzten Verfahren und Funktionsprinzipien aufgeführt, um den Leser bei der Auswahlentscheidung zu unterstützen. Nach einer kurzen Einführung in die physikalischen Grundlagen und Hinweisen zur elektromagnetischen Verträglichkeit, zum Strahlenschutz und zur regulierten Frequenzvergabe werden die verschiedenen Geräteklassen von Terahertz-Systemen ausführlich vorgestellt. Die Richtlinie gibt Hinweise zur messtechnischen Charakterisierung von Terahertz-Wellen. Einsatzgebiete von Terahertz-Systemen, wie die zerstörungsfreie Prüfung, die Dicken- und Abstandsmessung, die Tomografie und die chemische Analytik, werden mit ihren spezifischen Eigenschaften im Detail beschrieben. Umfangreiche Literaturverweise vereinfachen eine vertiefte Beschäftigung mit den Themen der Richtlinie. Eine tabellarische Übersicht mit einer Zusammenfassung, welche Terahertz-Systeme für welche Anwendungsfelder eingesetzt werden können, vervollständigt die Richtlinie. KW - Terahertzsysteme KW - THz-Wellen PY - 2018 UR - https://www.vdi.de/5590 VL - VDI/VDE 5590 Blatt 2 SP - 1 EP - 27 PB - VDI-Verlag CY - Düsseldorf ET - Entwurf - November 2018 AN - OPUS4-46727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hu, Y. A1 - Neumann, C. A1 - Scholtz, Lena A1 - Turchanin, A. A1 - Resch-Genger, Ute A1 - Eigler, S. T1 - Polarity, intramolecular charge transfer, and hydrogen bond comediated solvent effects on the optical properties of graphene quantum dots N2 - Graphene quantum dots (GQDs) have attracted increasing attention due to their favorable optical properties and have been widely used, e.g., in the biomedical field. However, the properties related to the chemical structure of GQDs, resulting in solventdependent optical properties, still remain unclear. Herein, we present the synthesis of long-wavelength emitting GQDs with a size of about 3.6 nm via a solvothermal method using oxo-functionalized graphene (oxo-G) and p-phenylenediamine as precursors and their structural and surface chemical analysis by transmission electron and atomic force microscopy (TEM; AFM) as well as Fourier-transform infrared, Raman, and X-ray photoelectron spectroscopy (FTIR; Raman; XPS). Subsequently, the influence of solvent polarity and proticity on the optical properties of the as-prepared GQDs bearing –OH, –NH2, –COOH and pyridine surface groups was investigated. Based on the results of the absorption and fluorescence (FL) studies, a possible luminescence mechanism is proposed. The observed solvent-induced changes in the spectral position of the FL maximum, FL quantum yield, and FL decay kinetics in protic and aprotic solvents of low and high polarity are ascribed to a combination of polarity effects, intramolecular charge transfer (ICT) processes, and hydrogen bonding. Moreover, the potential of GQDs for the optical sensing of trace amount of water was assessed. The results of our systematic spectroscopic study will promote the rational design of GQDs and shed more light on the FL mechanism of carbon based fluorescent nanomaterials. KW - Graphene quantum dots KW - Solvent polarity KW - solvent-induced changes KW - Charge transfer PY - 2022 DO - https://doi.org/10.1007/s12274-022-4752-1 SN - 1998-0124 SP - 1 EP - 8 PB - Springer AN - OPUS4-56030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, W. A1 - Said, Samir A1 - Rohrmann, R. A1 - Teng, J. A1 - Li, Z. A1 - Lu, W. A1 - Cunha, A. T1 - Operational modal analysis and continuous dynamic monitoring of structures N2 - This paper addresses operational modal analysis (OMA) and continuous dynamic monitoring (CDM) of two bridges. One of them is installed with Tuned Mass Dampers (TMDs) while another one is a normal bridge. Two ambient vibration tests were performed on these two bridges respectively. It is observed that not only installation of TMDs but also environmental factors influence the variations of structural frequencies, which may mask the subtle change induced by small structural changes. As a result, continuous dynamic monitoring systems were implemented on these two bridges, in order to evaluate efficiency of the TMD system, remove the environmental effects and build reliable damage indices that are only sensitive to structural changes. The results of CDM of these two bridges during several years are presented. Software systems developed for OMA and CDM are also introduced. T2 - 14th International Symposium on Structural Engineering (ISSE-14) CY - Beijing, Peoples Republic of China DA - 12.10.2016 KW - Structure KW - Operational modal analysis KW - Continuous dynamic monitoring PY - 2016 SN - 978-7-03-050125-7 VL - 2016 SP - 366 EP - 372 PB - Science Press Beijing AN - OPUS4-38876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhao, J. A1 - Hu, Y. A1 - wei Lin, S. A1 - Resch-Genger, Ute A1 - Zhang, R. A1 - Wen, J. A1 - Kong, X. A1 - Qin, A. A1 - Ou, J. T1 - Enhanced luminescence intensity of near-infraredsensitized sensitized upconversion nanoparticles via Ca²+ doping for a nitric oxide release platform N2 - Light-induced NO release based on exogenous NO donors has attracted substantial attention in clinical applications; the induction light source usually converts near-infrared light to blue or ultraviolet light. However, the low efficiency of near-infrared light-assisted chemical light energy conversion remains a challenge, especially for NaYF4:Yb3+/Tm3+ photoconverting near-infrared light to ultraviolet (UV) and blue light. In this paper, a luminescence-enhanced strategy is reported by doping Ca2+ into NaYF4:Yb3+/Tm3+ and coating it with NaGdF4 through a two-step solvothermal method. Then, UCNPs modified with methyl-b-cyclodextrin (M-b-CD) are loaded on a ruthenium nitrosyl complex [(3)Ru(NO)(Cl)] as nitric oxide release-molecules (NORMs). X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDS) data demonstrated that Ca2+ was successfully doped into NaYF4:Yb3+/Tm3+ nanoparticles as the core, and a pure hexagonal phase, NaYF4, was obtained from the doping of Ca2+. TEM revealed that the crystallinity was significantly improved after Ca2+ doping, and the core–shell structure was successfully synthesized, with NaGdF4 directionally grown on the NaYF4:Ca/Yb/Tm core. Fluorescence tests showed that, especially in the ultraviolet and blue light excitation wavelength regions, the UC emission intensity of the Ca-doped NaYF4:Yb3+/Tm3+@NaGdF4 core–shell UCNPs increased by 302.95 times vs. NaYF4:Yb3+/Tm3+ UCNPs. Finally, the release of NO was tested by the Griess method. Under 980 nm irradiation, the cell viability distinctly decreased with increasing UCNPs@M-b-CD-NORMs concentration. This study Shows that NORM release of NO is triggered by enhanced up-converted UV and blue light, which can be used for the development of UV photo-sensitive drugs. KW - Nano KW - Nanomaterial KW - Upconversion nanoparticle KW - Lanthanide KW - Photoluminescence KW - Quantum yield KW - Photophysics KW - Lifetime KW - Sensor KW - Surface chemistry KW - Single particle KW - Brightness KW - NIR KW - PDT PY - 2020 DO - https://doi.org/10.1039/d0tb00088d VL - 8 IS - 30 SP - 6481 EP - 6489 PB - Journal of Materials Chemistry B AN - OPUS4-51262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Wei-Hua A1 - Said, Samir A1 - Rohrmann, Rolf A1 - Rücker, Werner A1 - Cunha, A. T1 - Continuous dynamic monitoring of structures N2 - This paper presents the development of a continuous dynamic monitoring System and its applications to different structures, with the purpose of understanding structural real behaviours under operational conditions and detecting early structural modifications. The first part of paper introduces a complete continuous dynamic System, consists of signal acquisition and communication, automated signal processing and management, investigation of the interaction between structures and its environmental/operational conditions, feature extraction and detection of structural modification. The rest of paper describes the applications of continuous dynamic monitoring System to different structures such as a wind turbine System and a highway bridge. T2 - 13th International symposium on structural engineering (ISSE'13) CY - Hefei, China DA - 24.10.2014 KW - Continuous dynamic monitoring KW - Automated system identification KW - Environmental/operational effects KW - Resonance KW - Feature extraction KW - Structural modification PY - 2014 SN - 978-7-09-042032-9 SP - 1922 EP - 1933 PB - Science Press AN - OPUS4-32971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Wei-Hua A1 - Caetano, E. A1 - Cunha, A. A1 - Rücker, Werner ED - Carrera, E. ED - Miglioretti, F. ED - Petrolo, M. T1 - Comparison of different statistical approaches for removal of environmental/operational effects on modal properties and damage detection N2 - The implementation of a continuous dynamic monitoring System in Pedro e Ines footbridge at Coimbra, Portugal, operating since June 2007, enabled to detect different environmental/operational effects on the modal properties, based on appropriate processing of monitoring data collected by a set of accelerometers and thermal sensors. In order to remove or mitigate such environmental/operational effects with the purpose of damage detection, two different Statistical methods have been adopted, One of them consists in the multiple linear regression (MLR) by performing correlation analysis between measured modal properties and environmental/operational variables. Another is based on the identification of the linear subspace within the modal properties by applying principal component regression (PCR) without using measured values of environmental and operational variables. This paper presents a comparison ofthe performance of these two alternative approaches on the basis of continuous monitoring data acquired front the instrumented Pedro e Ines footbridge. T2 - SMART2013 - 6th ECCOMAS conference on smart structures and materials CY - Turin, Italy DA - 24.06.2013 KW - Structural health monitoring KW - Environmental/operational effects KW - Principal component regression KW - Multiple linear regression KW - Damage detection PY - 2013 SP - 1 EP - 13 AN - OPUS4-32972 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Wei-Hua A1 - Said, Samir A1 - Rohrmann, Rolf A1 - Rücker, Werner A1 - Cunha, A. A1 - Rogge, Andreas ED - De Stefano, A. T1 - Vibration-based structural health monitoring of a highway bridge based on continuous dynamic measurements during 14 years N2 - This paper presents the continuous dynamic measurements of an aging prestressed box-beam bridge during the period from 2000 to 2013, which consists of dynamic properties and environmental/operational factors, as well as the Variation of the extracted health features after removing the environmental/operational effects. Firstly, the variations of frequency estimates, temperatures and traffic loads from 2000 to 2013 are described. Subsequently, correlation analysis between them indicates the nonlinear influences of the temperature on the frequency estimates. The Multiple Linear Regression (MLR) method is used to remove the environmental/operational effects and the health index is proposed by performing the Novelty Detection analysis of the residual errors. Finally, the variations of the health index may indicate clear structural modifications that can be also characterized by the long term monitoring of the dynamic strain in the prestressed cable. T2 - SHMII-7 - 7th International conference on structural health monitoring of intelligent infrastructure CY - Torino, Italy DA - 01.07.2015 KW - Westend bridge PY - 2015 SP - 1 EP - 12 AN - OPUS4-35124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hu, W.-H. A1 - Said, Samir A1 - Rohrmann, R. A1 - Cunha, À. A1 - Teng, J. T1 - Continuous dynamic monitoring of a prestressed concrete bridge based on strain, inclination and crack measurements over a 14-year span N2 - The Westend Bridge is located on the A100 Highway in Berlin. An integrated continuous dynamic monitoring system, composed of 20 velocity sensors, 5 temperature sensors, 3 strain gauges, 1 crack sensor and 2 inclination sensors, was implemented by the Federal Institute for Materials Research and Testing in 2000. The system runs continuously with occasional intermittence and led to a huge amount of data over a 14-year span. In this article, variations of the strain, crack and inclination measurements during the last 14 years are presented. It is noted that the observed crack and inclination of the bridge are strongly influenced by seasonal temperature variation. It further induces change in the relationship between the strains measured in both concrete and prestressed tendon. Application of k-means cluster Analysis technique in both the crack and strain measurements can partition them into different seasonal phases by identifying ‘turning points’ that indicate annual periodical bridge change. In the period of these two ‘turning points’, a strong linear relation of the strains in two materials is observed. In the rest of the year, a nonlinear relationship between the strains recorded in both the concrete and the prestressed tendon is noted. The possible reason is the additional thermal load due to the change in temperature difference between the bridge’s surface and soffit. Finally, a health index in a Framework of regression model and process control theory is proposed by investigating the linear relationship between the strains in concrete and prestressed tendon. The tendency of the health index in the 14 years may suggest the long-term bridge change during that time frame. KW - Detection of structural change KW - Structural health monitoring KW - Strain KW - Crack KW - Inclination KW - Bridge PY - 2017 DO - https://doi.org/10.1177/1475921717735505 VL - 17 IS - 5 SP - 1073 EP - 1094 PB - SAGE CY - USA/UK AN - OPUS4-45990 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hu, W.‐H. A1 - Álvaro Cunha, Á. A1 - Caetano, E. A1 - Rohrmann, R. G. A1 - Said, Samir A1 - Teng, J. T1 - Comparison of different statistical approaches for removing environmental/operational effects for massive data continuously collected from footbridges N2 - The implementation of continuous dynamic monitoring systems in two bridges, in Portugal, is enabled to detect the occurrence of very significant environmental and operational effects on the modal properties of these bridges, based on automated processing of massive amounts of monitoring data collected by a set of accelerometers and thermal sensors over several years. In order to remove or mitigate such environmental/operational effects with the purpose of damage detection, two different statistical methods have been adopted. One of them is the multiple linear regression by performing nonlinear correlation analysis between measured modal properties and environmental/operational variables. Another one is principal component regression based on the identification of the linear subspace within the modal properties without using measured values of environmental and operational variables. This paper presents a comparison of the performance of these two alternative approaches on the basis of continuous monitoring data acquired from two instrumented bridges and simulated damage scenarios. It is observed that different methods show similar capacity in removing environmental effects, and the multiple linear regression method is slightly more sensitive to structural damage. KW - Multiple linear KW - Damage detection KW - Environmental/operational effect KW - Modal property PY - 2017 DO - https://doi.org/10.1002/stc.1955 SN - 1545-2255 VL - 24 IS - 8 SP - e1955-1 EP - e1955-19 PB - John Wiley & Sons, Ltd AN - OPUS4-41147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zheng, Y. A1 - Zhang, S. A1 - Ma, J. A1 - Sun, F. A1 - Osenberg, M. A1 - Hilger, A. A1 - Markötter, Henning A1 - Wilde, F. A1 - Manke, I. A1 - Hu, Z. A1 - Cui, G. T1 - Codependent failure mechanisms between cathode and anode in solid state lithium metal batteries: mediated by uneven ion flux N2 - An in-depth understanding of the degradation mechanisms is a prerequisite for developing the nextgeneration all solid-state lithium metal battery (ASSLMB) technology. Herein, synchrotron X-ray computed tomography (SXCT) together with other probing tools and simulation method were employed to rediscover the decaying mechanisms of LiNi0.8Co0.1Mn0.1O2 (NCM)|Li6PS5Cl (LPSCl)|Li ASSLMB. It reveals that the detachment and isolation of NCM particles cause the current focusing on the remaining active regions of cathode. The extent of Li stripping and the likelihood of Li+ plating into LPSCl facing the active NCM particles becomes higher. Besides, the homogeneity of Li stripping/plating is improved by homogenizing the electrochemical reactions at the cathode side by LiZr2(PO4)3 (LZP) coating. These results suggest a codependent failure mechanism between cathode and anode that is mediated by uneven Li ion flux. This work contributes to establish a holistic understanding of the degradation mechanisms in ASSLMBs and opens new opportunities for their further optimization and evelopment. KW - Current density distribution KW - Lithium ion flux KW - Solid-state lithium metal batteries KW - Codependent failure mechanism KW - Cathode deactivation PY - 2023 DO - https://doi.org/10.1016/j.scib.2023.03.021 SN - 2095-9273 VL - 68 IS - 8 SP - 813 EP - 825 PB - Elsevier B.V. AN - OPUS4-57309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -