TY - JOUR A1 - Droste, Bernhard A1 - Völzke, Holger A1 - Wieser, Günter A1 - Qiao, Linan T1 - Safety Margins of Spent Fuel Transport and Storage Casks Considering Aircraft Crash Impacts JF - International journal of radioactive materials transport (RAMTRANS) PY - 2002 SN - 0957-476X VL - 13 IS - 3-4 SP - 313 EP - 316 PB - Nuclear Technology Publ. CY - Ashford, Kent AN - OPUS4-2697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Lange, F. A1 - Hörmann, E. A1 - Schwarz, G. A1 - Droste, Bernhard A1 - Völzke, Holger A1 - Wieser, Günter T1 - Spent Fuel Transport and Storage Casks under Extreme Accidents T2 - Progress through cooperation T2 - 10th International High-Level Radioactive Waste Management Conference (IHLRWM-10) CY - Las Vegas, NV, USA DA - 2003-03-30 PY - 2003 SN - 0-89448-669-1 SP - 465 EP - 470 PB - American Nuclear Society CY - La Grange Park, Ill. AN - OPUS4-2698 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Droste, Bernhard A1 - Zencker, Uwe T1 - Safety Assessment Aspects of Materials for Radioactive Waste Containers T2 - 4th International Seminar on Radioactive Waste Products T2 - 4th International Seminar on Radioactive Waste Products CY - Würzburg, Germany DA - 2002-09-22 PY - 2002 AN - OPUS4-5742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Kasparek, Eva Maria A1 - Völzke, Holger T1 - Modeling of cylindrical casks under horizontal drop test conditions T2 - IHLRWM 2013 - 14th International high-level radioactive waste management conference (Proceedings) N2 - Cylindrical casks made of ductile cast iron are used for transport, interim storage and final disposal of radioactive waste in Germany. A basic design criterion is the ability to withstand a horizontal drop without impact Binders onto a foundation representative for the real ground of a storage facility. The increasing use of more cost-effective material compositions requires optimized cask geometries to reduce stresses and strains in the cask structure. For example, a non-uniform wall thickness was introduced to reduce maximum wall bending stresses. As a result, the load characteristics changed from line load to point load at bottom and lid side under horizontal drop fest conditions. Hereby, the position of highest stress inside the structure has shifted significantly. This was the reason for a systematic investigation of effects caused by small design changes or small variations of fest conditions. It led to a better understanding of the positions of high local stresses, their time history and maximum value for cylindrical casks under horizontal drop test conditions. Hence, the paper presents the lessons learnt from modeling and simulating such scenarios considering an impact without limiters onto a realistic target. T2 - 14th International high-level radioactive waste management conference CY - Albuquerque, New Mexico, USA DA - 28.04.2013 KW - Cylindrical cask KW - Ductile cast iron KW - Numerical simulation KW - Horizontal drop test KW - Storage facility KW - Concrete foundation PY - 2013 SN - 978-1-62748-644-6 SP - 1114 EP - 1119 (Paper # 6862) PB - Omnipress AN - OPUS4-28529 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Völzke, Holger A1 - Wolff, Dietmar T1 - Extended storage collaboration program international subcommittee report: International perspectives on technical data gaps associated with extended storage and transportation of used nuclear fuel PY - 2012 VL - 1026481 IS - Chapter 2.1, 3.1, 4.1 SP - 2-1 - 2-5, 3-1 - 3-4, 4-1 - 4-3 CY - Palo Alto, CA, USA ET - Final report AN - OPUS4-27405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Dynamic crushing characteristics of spruce wood under large deformations JF - Wood science and technology N2 - An extensive series of large deformation crushing tests with spruce wood specimens was conducted. Material orientation, lateral constraint and loading rate were varied. Regarding material orientation, a reduction in the softening effect and the general force level was observed with a higher fiber-load angle. A comparison with characteristics gained by application of Hankinson's formula showed discrepancies in compression strength and the beginning of the hardening effect. Lateral constraint of the specimens caused a multiaxial stress state in the specimens, which was quantified with the applied measuring method. Further, a higher force level compared to specimens without lateral constraint and significant hardening effect at large deformations resulted. Thus, the influence of a multiaxial stress state on the force level could be determined. An increase in the loading rate led to higher force levels at any displacement value and material orientation. KW - Crushing test KW - Dynamic crushing characteristics KW - Spruce wood KW - Lateral constraint KW - Multiaxial stress state KW - Hankinson's formula PY - 2013 DO - https://doi.org/10.1007/s00226-012-0508-5 SN - 0043-7719 SN - 1432-5225 VL - 47 IS - 2 SP - 369 EP - 380 PB - Springer CY - Berlin AN - OPUS4-27743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Qiao, Linan A1 - Zencker, Uwe A1 - Wieser, Günter A1 - Völzke, Holger ED - Topping, B. H. V. ED - M. Papadrakakis, T1 - Numerical safety assessment of a transport and storage cask for radioactive materials without impact limiters by the 0.3m drop test onto an unyielding target T2 - 9th International Conference on Computational Structures Technology (Proceedings) T2 - 9th International Conference on Computational Structures Technology (CST2008) CY - Athens, Greece DA - 2008-09-02 KW - Impact KW - Simulation KW - Cask KW - Safety KW - Drop KW - Foundation KW - Unyielding KW - Target PY - 2008 SN - 978-1-905088-23-2 IS - Paper 21 SP - 1 EP - 10 PB - Civil Comp Press CY - Kippen AN - OPUS4-18340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Feutlinske, Karl A1 - Musolff, André T1 - Drop tests and numerical impact analyses of new cask designs for high activity waste (HAW) and spent fuel - updated BAM design testing experiences - T2 - Waste Management Conference 2007 T2 - Waste Management Conference 2007 CY - Tucson, AZ, USA DA - 2007-02-25 PY - 2007 AN - OPUS4-14577 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Völzke, Holger A1 - Noack, Volker A1 - Weber, Wolfgang A1 - Wolff, Dietmar A1 - Rittscher, D. A1 - Schmidt, H. T1 - Long term interim storage facility for nuclear reactor compartments of submarines - German support for utilization of nuclear submarines in Russia T2 - PATRAM 2007 - 15th International symposium on the packaging and transportation of radioactive materials (Proceedings) T2 - PATRAM 2007, 15th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Miami, Florida, USA DA - 2007-10-21 PY - 2007 SP - 155 PB - Institute of Nuclear Materials Management AN - OPUS4-16157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sterthaus, Jens A1 - Ballheimer, Viktor A1 - Droste, Bernhard A1 - Koch, Frank A1 - Probst, Ulrich A1 - Völzke, Holger A1 - Wille, Frank T1 - Analysis of bolted flange joints for lids of packages for radioactive materials T2 - PVP2009 - ASME 2009 Pressure vessels and piping conference (Proceedings) T2 - ASME 2009 Pressure vessels and piping conference CY - Prague, Czech Republic DA - 2009-07-26 KW - Bolted flange joints KW - FEA KW - Modelling of gaskets KW - Assessment of leak tightness KW - Results from experiments PY - 2009 SP - PVP2009-77284, 1-8 PB - American Society of Mechanical Engineers CY - New York AN - OPUS4-19786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -