TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike T1 - Wie beeinflussen nicht-atmosphärische Bedingungen das Deflagrationsverhalten? N2 - Zur Bestimmung der Deflagrationsfähigkeit von energiereichen Stoffen/ Gemischen wurde zuletzt ein Vier-Liter-Autoklav vorgeschlagen, der im Vergleich zu den derzeit gängigen Prüfmethoden eine Reihe von Vorteilen bietet. In diesem Beitrag wird der Frage nachgegangen, wie nicht-atmosphärische Bedingungen das Deflagrationsverhalten beeinflussen. Zur Beantwortung dieser Frage wurden weitere Experimente im genannten Autoklaven und in einem kleineren Autoklaven durchgeführt. Im Wesentlichen lässt sich feststellen, dass der Druck im Probengefäß vor Versuchsbeginn, insbesondere reduzierter Ausgangsdruck < 1 bar Auswirkungen auf das Deflagrationsverhalten hat. Das Vorhandensein einer reinen Stickstoffatmosphäre hingegen, beeinflusst das Deflagrationsverhalten nicht. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Nicht-atmosphärische Bedingungen PY - 2015 SN - 978-3-86011-091-1 SP - P12, 1 EP - 4 AN - OPUS4-34821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosenberg, Marika A1 - Michael-Schulz, Heike A1 - Wehrstedt, Klaus-Dieter A1 - Malow, Marcus T1 - Validation of the UN test method N.5 N2 - Many substances react with water in such a way that flammable gases are formed. For transport issues this reaction may possess a considerable hazard especially if the cargo is wetted by rain or by water from other sources. In the UN Recommendations on the Transport of Dangerous Goods these kinds of problems are addressed. The UN test N.5 'Test method for substances which in contact with water emit flammable gases' corresponds to this hazard. Classification according to the test method is done by measurement of the gas evolution rate of the flammable gas by any suitable procedure. At BAM a gravimetric approach is used to measure the gas evolution rate. In this paper we present the evaluation of the apparatus by means of an absolute calibration routine utilizing a reaction where a known amount of gas is produced as well as the evaluation of important parameters influencing the gas evolution rate using different substances. It can be shown that the apparatus is capable of measuring absolute gas volumes as low as 6 mL with an acceptable error of about 17% as determined from the reaction of Mg with demineralized water. KW - UN test N.5 KW - Water reactive substance KW - Flammable gas KW - Magnesium KW - Aluminum KW - Hydrogen PY - 2014 DO - https://doi.org/10.1016/j.jlp.2014.03.008 SN - 0950-4230 SN - 1873-3352 VL - 30 SP - 282 EP - 286 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-31037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Gebauer, Marek T1 - Experimentelle und theoretische Untersuchung des Zersetzungsmechanismus deflagrationsfähiger Substanzen N2 - Dieser Beitrag beschreibt Untersuchungen zu Deflagrationen von Azodicarbonamid, welche erstmals in einem Vier-Liter-Autoklaven durchgeführt wurden. Zunächst wird die Reproduzierbarkeit der Messungen mit der neuen Apparatur überprüft. Anschließend wird ein Vergleich mit Messungen in einer offenen Apparatur hergestellt, welche zur Prüfung der Deflagrationsfähigkeit in VDI 2263-1 erläutert ist. Zur Beschreibung der deflagrativen Zersetzungen werden die Kenngrößen Induktionszeit, Deflagrationsgeschwindigkeit, maximaler Druck, maximale und mittlere Druck- und Tempe-raturanstiegsrate herangezogen. Zusätzlich werden in weiteren Versuchen die während einer Deflagration entstehende Gasmenge und die Gasentwicklungsrate bestimmt. Abschließend werden die Druck- und Gasentwicklungsraten miteinander verglichen. Aus den Arbeiten lässt sich folgern, dass der Vier-Liter-Autoklav zur Bestimmung und Beschreibung der Deflagrationsfähigkeit von Azodicarbonamid gut geeignet ist und im Vergleich zu Messungen in offenen Prüfanordnungen eine Reihe von Vorteilen bietet. T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung CY - Magdeburg, Germany DA - 26.03.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Gas- und Druckmengenmessung PY - 2015 UR - http://www.iaut.ovgu.de/iaut_media/MBE/4_+MBE+2015/Beitr%C3%A4ge+2015/Salg_Experimentelle+und+theoretische+Untersuchung+des+Zersetzungsmechanismus+deflagrationsf%E2%80%9Ehiger+Substanzen.pdf SN - 978-3-00-048960-0 SP - 1 EP - 13 AN - OPUS4-33411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - SADT and Storage Group Assignement of Artimisinin T2 - IGUS EOS Meeting CY - Nanjing, China DA - 2014-04-09 PY - 2014 AN - OPUS4-30557 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Koenen Test - Quality of Steel Tubes T2 - IGUS EOS Meeting CY - Nanjing, China DA - 2014-04-09 PY - 2014 AN - OPUS4-30558 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Uhlig, S. A1 - Frost, K. A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Schmidt, Martin A1 - Zakel, S. T1 - CEQAT-DGHS interlaboratory tests for chemical safety: Validation of laboratory test methods by determining the measurement uncertainty and probability of incorrect classification including so-called “Shark profiles” N2 - Laboratory test results are of vital importance for correctly classifying and labelling chemicals as “hazardous” as defined in the UN Globally Harmonized System (GHS) / EC CLP Regulation or as “dangerous goods” as defined in the UN Recommendations on the Transport of Dangerous Goods. Interlaboratory tests play a decisive role in assessing the reliability of laboratory test results. Interlaboratory tests performed over the last 10 years have examined different laboratory test methods. After analysing the results of these interlaboratory tests, the following conclusions can be drawn: 1. There is a need for improvement and validation for all laboratory test methods examined. 2. To avoid any discrepancy concerning the classification and labelling of chemicals, the use of validated laboratory test methods should be state of the art, with the results accompanied by the measurement uncertainty and (if applicable) the probability of incorrect classification. This paper addresses the probability of correct/incorrect classification (for example, as dangerous goods) on the basis of the measurement deviation obtained from interlaboratory tests performed by the Centre for quality assurance for testing of dangerous goods and hazardous substances (CEQAT-DGHS) to validate laboratory test methods. This paper outlines typical results (e.g. so-called “Shark profiles” – the probability of incorrect classification as a function of the true value estimated from interlaboratory test data) as well as general conclusions and steps to be taken to guarantee that laboratory test results are fit for purpose and of high quality. T2 - 13th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE 2020) CY - Braunschweig, Germany DA - 27.07.2020 KW - Dangerous goods KW - Hazardous substances KW - Interlaboratory test KW - Test method KW - Validation KW - Quality assurance KW - Measurement uncertainty KW - Incorrect classification KW - Shark profile PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-515376 UR - https://oar.ptb.de/files/download/5f3e662f4c93901010006dbf DO - https://doi.org/10.7795/810.20200724 VL - 2020 SP - 50 EP - 61 PB - Open Access Repository der Physikalisch-Technischen Bundesanstalt (PTB-OAR) CY - Braunschweig AN - OPUS4-51537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Quinone dioxime - QDO N2 - Der Vortrag beschreibt die Eigenschaften und die Einstufung von QDO. Die Prüfergebnisse sind nicht frei zugänglich. Der Vortrag wurde im Kreis der international zuständigen Behörden gehalten. T2 - IGUS-EOS CY - Manchester, Great Britain DA - 24.04.2024 KW - UN-Manual of Tests and Criteria KW - UN-Methods KW - Classification of Dangerous Goods KW - Explosives of the Chemical Industries PY - 2024 AN - OPUS4-60858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Brandes, E. A1 - Frost, K. A1 - Kurth, Lutz A1 - Schmidt, Martin A1 - Michael-Schulz, Heike A1 - Uhlig, S. T1 - CEQAT-DGHS Ringversuchsprogramm der BAM in Kooperation mit QuoData und PTB N2 - Bei der Bewertung der Verlässlichkeit der im Labor gewonnenen Prüfergebnisse spielen Ringversuche eine entscheidende Rolle. Die Bundesanstalt für Materialforschung und -prüfung (BAM) unterstützt deshalb den weiteren Ausbau des Ringversuchsprogramms des im Jahr 2007 gegründeten Kompetenzzentrums zur Qualitätssicherung für Prüfungen von Gefahrgütern und Gefahrstoffen auf physikalische Gefahren (Centre for quality assurance for testing of dangerous goods and hazardous substances, CEQAT-DGHS). Bei allen bisher untersuchten Prüfmethoden besteht ein Verbesserungsbedarf. Die RV müssen daher zunächst auf die Methodenentwicklung, -verbesserung und -validierung abzielen und nicht auf Leistungstests. T2 - 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik (BAM-PTB-Kolloquium) CY - Berlin, Germany DA - 14.06.2016 KW - Gefahrgut KW - Gefahrstoff KW - Ringversuch KW - Prüfmethode KW - Validierung KW - Qualitätssicherung PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 SP - 143 EP - 143 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Brandes, E. A1 - Frost, K. A1 - Kurth, Lutz A1 - Schmidt, Martin A1 - Michael-Schulz, Heike A1 - Uhlig, S. T1 - CEQAT-DGHS Ringversuchsprogramm für die Chemikaliensicherheit – Methodenvalidierung N2 - Bei der Bewertung der Verlässlichkeit der im Labor gewonnenen Prüfergebnisse spielen Ringversuche eine entscheidende Rolle. Die Bundesanstalt für Materialforschung und –prüfung (BAM) unterstützt deshalb den weiteren Ausbau des Ringversuchsprogramms des im Jahr 2007 gegründeten Kompetenzzentrums zur Qualitätssicherung für Prüfungen von Gefahrgütern und Gefahrstoffen auf physikalische Gefahren (Centre for quality assurance for testing of dangerous goods and hazardous substances, CEQAT-DGHS). Bei allen bisher untersuchten Prüfmethoden besteht ein Verbesserungsbedarf. Die RV müssen daher zunächst auf die Methodenentwicklung, -verbesserung und -validierung und auf die Bestimmung der Messunsicherheit der jeweiligen Prüfmethode abzielen und nicht auf Leistungstests. T2 - 13. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 16.11.2017 KW - Gefahrgut KW - Gefahrstoff KW - Ringversuch KW - Prüfmethode KW - Validierung KW - Qualitätssicherung PY - 2017 SN - 978-3-96057-032-5 SP - 1 EP - 13 CY - Köthen AN - OPUS4-43299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Polymerizing Substances N2 - Polymerizing substances are classified in different classes of the UN Recommendations on the Transport of Dangerous Goods. Based on incidents a new division 4.1 for polymerizing substances, which are not meet the criteria of the Classes 1-8, was implemented in the regulations. In the lecture, the criteria and the determination of the SAPT (self-accelerating polymerization temperature are discussed. T2 - IGUS EOS Meeting CY - Rijswijk, The Netherlands DA - 24.04.2017 KW - Polymerizing substances KW - Determination KW - SAPT KW - Classification PY - 2017 AN - OPUS4-43072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -