TY - JOUR A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Experimental Results of a Pull-Out Test Performed with Single- and Multi-Fiber Samples N2 - Widely-used methods for characterising the fibre/matrix interface in polymeric composites are the fragmentation test and the droplet test as a special kind of the single-fibre pull-out test. A severe disadvantage of these tests is that non-realistic model samples are investigated which contain only one fibre in the matrix. In order to obtain data about the effect of the different residual stress situations for fibres in such samples and in composites, pull-out tests of E-glass fibres in polystyrene and polycarbonate are performed using samples, where the investigated fibre is surrounded by 0 to 3 other near fibres. Neighbouring fibres can increase the pull-out forces by a factor of three and the interfacial toughness by a factor of four. This has to be taken into account, if the tests are performed not only for comparison reasons but for measuring interface properties. KW - Interface KW - Fiber pull-out KW - Residual stress KW - Fracture toughness KW - Friction PY - 2002 DO - https://doi.org/10.1080/00218460210381 SN - 0021-8464 SN - 1545-5823 VL - 78 IS - 2 SP - 167 EP - 187 PB - Gordon & Breach CY - New York, NY AN - OPUS4-1975 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hampe, Andreas A1 - Harbich, Karl-Wolfram A1 - Hentschel, Manfred P. A1 - Rudolph, Hans-Volker T1 - The Determination of Inner Surfaces in Composites by X-Ray Refraction T2 - 12th International Conference on Composite Materials ; 12th ICCM Europe CY - Paris, France DA - 1999-07-05 PY - 1999 SN - 2-9514526-2-4 IS - 423 CY - Paris AN - OPUS4-3273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas T1 - Dielektrische Relaxation in vernetztem PVC PY - 1976 SN - 0303-402X SN - 1435-1536 VL - 254 SP - 148 EP - 154 PB - Springer CY - Berlin AN - OPUS4-8426 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard T1 - Energy based characterization of the fibre-matrix interface using the pull-out and push-in test T2 - Interfacial Phenomena in Composite Materials 97 CY - Eger, Hungary DA - 1997-03-01 PY - 1997 AN - OPUS4-12087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Bohse, Jürgen A1 - Kalinka, Gerhard A1 - Schulz, Eckhard T1 - Bruchzähigkeit und Phasenhaftung von unidirektionalen PP/GF-Verbunden T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Kaiserslautern, Germany DA - 1997-09-17 PY - 1997 AN - OPUS4-12088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Schulz, Eckhard A1 - Meretz, S. T1 - An Advanced Equipment for Single-Fibre Pull-Out test designed to monitor the fracture process T2 - Interfacial Phenomena in Composite Materials CY - Cambridge, England DA - 1993-09-13 PY - 1993 AN - OPUS4-12095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard T1 - An Advanced Indentation Technique for the Characterization of the Fibre-Matrix Interface T2 - Gordon Conference on Composites CY - San Buenaventura, CA, USA DA - 1997-01-05 PY - 1997 AN - OPUS4-12102 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hampe, Andreas A1 - Mielke, Werner A1 - Boro, I. T1 - Charakterisierung von Versagensmechanismen an Einzelfaserproben T2 - DKI-Tagung CY - Darmstadt, Deutschland DA - 1988-04-12 PY - 1988 SN - 3-927090-00-X SP - 45 EP - 48 PB - Deutsches Kunststoff-Institut CY - Darmstadt AN - OPUS4-11950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hampe, Andreas A1 - Marotzke, Christian ED - Brockmann, W. T1 - Messung der Scherfestigkeit in der Grenzfläche zwischen Polymer und Glas durch Einzelfaserexperimente T2 - 3. Symposiums der DGM CY - Konstanz DA - 1990-06-21 PY - 1989 SN - 3-88355-166-X PB - DGM Informationsges. CY - Oberursel AN - OPUS4-6806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Marotzke, Christian A1 - Hampe, Andreas A1 - Qiao, Linan T1 - Influence of the Interface Strenght on Local Failure Processes in Fiber Reinforced Composites T2 - 12th International Conference on Composite Materials ; 12th ICCM Europe CY - Paris, France DA - 1999-07-05 KW - Interface crack KW - Energy release rate KW - Fracture mechanics KW - Debonding KW - Thermal stresses KW - Friction KW - Finite element method KW - FEM PY - 1999 SN - 2-9514526-2-4 IS - 423 CY - Paris AN - OPUS4-6809 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meretz, S. A1 - Auersch, W. A1 - Marotzke, Christian A1 - Schulz, Eckhard A1 - Hampe, Andreas T1 - Investigation of Morphology-dependent Fracture Behaviour with the Single-fibre Pull-out Test PY - 1993 SN - 0266-3538 VL - 48 SP - 285 EP - 290 PB - Elsevier CY - Barking AN - OPUS4-6821 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The fracture toughness of the glass fibre/polymer matrix interface: measurement and theoretical analysis T2 - The fracture toughness of the glass fibre/polymer matrix interface: measurement and theoretical analysis CY - Guildford, England, UK DA - 1995-03-27 PY - 1995 CY - Guildfort AN - OPUS4-6823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The energy release rate of the fiber/polymer matrix interface: measurement and theoretical analysis PY - 1995 SP - 326 EP - 335 PB - Technomic Publ. CY - Lancaster AN - OPUS4-6824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Marotzke, Christian A1 - Hampe, Andreas T1 - Micromechanics of the interface in polymer composites capabilities and limitations of the common test methods T2 - 10th International Conference on Composite Materials CY - Quebec, Canada DA - 1995-05-08 PY - 1995 SN - 1-566-76313-4 VL - 6 SP - 517 EP - 524 PB - Technomic Publ. CY - Lancaster, Pa. AN - OPUS4-6825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The Energy Release Rate of the Fiber/Polymer Matrix Interface: Measurement and Theoretical Analysis PY - 1997 SN - 0731-6844 SN - 1530-7964 VL - 16 IS - 4 SP - 341 EP - 352 PB - Technomic Publ. Co. CY - Westport, Conn. AN - OPUS4-6827 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Marotzke, Christian A1 - Hampe, Andreas ED - Scott, M. T1 - Fracture Mechanical Analysis of Pull-out and Fragmentation Tests T2 - 11th International Conference on Composite Materials CY - Gold Coast, Queensland, Australia DA - 1997-07-14 PY - 1997 SN - 1-85573-350-1 SP - V863 EP - V872 PB - Woodhead CY - Cambridge AN - OPUS4-6828 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Adhesion of polymers to reinforced fibres PY - 1992 SN - 0959-8103 SN - 1097-0126 SN - 0007-1641 VL - 28 SP - 313 EP - 318 PB - Wiley InterScience CY - Chichester, West Sussex AN - OPUS4-6817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Mielke, Werner A1 - Hampe, Andreas A1 - Hoyer, O. A1 - Schumacher, Klaus T1 - Analysis of AE-events from single fibre pull-out experiments T2 - 3rd International Symposium on Acoustic Emission from Composite Materials CY - Paris, France DA - 1989-07-17 PY - 1989 SN - 0-931403-88-X SP - 323 EP - 331 PB - American Soc. for Nondestructive Testing CY - Columbus, Ohio AN - OPUS4-11804 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Hennecke, Manfred A1 - Mielke, Werner T1 - Prüfmethoden für Polymerwerkstoffe - Entwicklungen in der Prüftechnik PY - 1992 SN - 0025-5300 VL - 34 IS - 7-8 SP - 228 EP - 231 PB - Carl Hanser Verlag CY - München AN - OPUS4-11808 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Mielke, Werner A1 - Hampe, Andreas A1 - Lützow, Wolfgang A1 - Müller, Hansjörg A1 - Pastuska, Gerhard A1 - Rook, A. A1 - Schnabel, E. A1 - Sickfeld, Jürgen A1 - Tobisch, Karl A1 - Trubiroha, Peter T1 - Einsatz von Kunststoffen in Pkw - Literaturstudie PY - 1990 SN - 0937-1214 IS - 2 SP - 9 EP - 257 PB - Bundesanstalt für Straßenwesen CY - Bergisch Gladbach AN - OPUS4-11796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mielke, Werner A1 - Hampe, Andreas A1 - Hoyer, O. A1 - Schumacher, Klaus T1 - Analysis of acoustic emission events from single fiber pullout experiments PY - 1990 SN - 0730-0050 VL - 9 IS - 2 SP - 103 EP - 108 PB - Acoustic Emission Group CY - Los Angeles, Calif. AN - OPUS4-11800 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Messung der Scherfestigkeit in der Grenzfläche zwischen Polymer und Glas durch Einzelfaserexperimente T2 - DGM Tagung "Haftung bei Verbundwerkstoffen und Werkstoffverbunden" CY - Konstanz, Germany DA - 1990-06-21 PY - 1990 AN - OPUS4-5962 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Experimental Results of a Pull-Out-Test T2 - 24th Annual Meeting of the Adhesion Society, Inc. CY - Williamsburg, VA, USA DA - 2001-02-25 PY - 2001 AN - OPUS4-5951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Shear strength of fibre/matrix interface, measuring technique and stress analysis T2 - 5th Technical Conference of the American Society for Composites, Michigan State University CY - East Lansing, MI, USA DA - 1990-06-11 PY - 1990 AN - OPUS4-5960 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas T1 - Vergleich thermisch stimulierter Ströme von elektronenbestrahltem und im elektrischen Feld polarisiertem Polyäthylen PY - 1977 SN - 0340-255x SN - 1437-8027 VL - 62 SP - 154 EP - 160 PB - Springer CY - Berlin AN - OPUS4-8685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Leistner, André A1 - Hampe, Andreas T1 - Characterisation of the fibre/matrix interface in reinforced polymers by the push-in technique N2 - The push-in test is the only micromechanical test method that is not restricted to artificial fibre/matrix arrangements, but allows the in situ characterisation of interfaces in composites fabricated and stressed under realistic conditions. However, with the application of this method to reinforced polymers some problems arise both in the mathematical model for evaluating test data and in the practical performance of the test. Because in some cases the deformation of the relatively compliant polymeric matrices cannot be neglected, an extension of the existing model is required. For this purpose, the elastic energy of the material around the debonded part of the fibre is estimated and included in the energy-balance analysis. Because of the small diameter of the fibres usually used for reinforcing polymers, a test apparatus was designed which ensures a high positioning accuracy in the xy plane as well as in the z direction. In order to minimise thermal and mechanical influences, the microscope for fibre selection and the force sensor/indenter are directly connected together and the apparatus is designed to be stiff in all components. A solid-state bending joint guarantees very precise control of the axial movement. Three examples of the application of this easy-to-handle and low-cost test apparatus are presented briefly in the paper: assess fibre/matrix combinations, measures to improve the interfacial adhesion and the influence of water on the interface. KW - Interface KW - Test method KW - Characterisation KW - Indentation KW - Push-in PY - 1997 SN - 0266-3538 VL - 57 IS - 8 SP - 845 EP - 851 PB - Elsevier CY - Barking AN - OPUS4-12011 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Schulz, Eckhard T1 - An advanced equipment for single-fibre pull-out test designed to monitor the fracture process KW - Verbundwerkstoffe KW - Thermoplaste KW - Adhäsion KW - Reibung KW - Haftung KW - Interface KW - Schubfestigkeit KW - Scherfestigkeit KW - Messmethode PY - 1995 SN - 0010-4361 VL - 26 IS - 1 SP - 40 EP - 46 PB - Butterworth-Heinemann CY - Guildford, Surrey AN - OPUS4-11988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Hampe, Andreas T1 - Pull-out of Single Fibres KW - Verstärkungsfaser KW - Verbundwerkstoffe KW - Interface KW - Adhäsion KW - Reibung KW - Haftung KW - Thermoplast PY - 1994 SN - 0945-0084 VL - 84 IS - 5 SP - 25 EP - 26 PB - Hanser CY - München AN - OPUS4-11989 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Hampe, Andreas T1 - Einzelfaserauszug - Eine Methode zum Bestimmen der Grenzflächenfestigkeit KW - Verstärkungsfaser KW - Verbundwerkstoffe KW - Interface KW - Adhäsion KW - Reibung KW - Haftung KW - Thermoplast PY - 1994 SN - 0023-5563 VL - 84 IS - 5 SP - 608 EP - 610 PB - Hanser CY - München AN - OPUS4-11994 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Boro, I. A1 - Augustin, G. A1 - Hampe, Andreas A1 - Hinrichsen, G. T1 - Ermüdungsverhalten von Hochleistungs-Faserverbundwerkstoffen mit thermoplastischer Matrix KW - Verbundwerkstoffe KW - Ermüdung KW - Biegeschwingung KW - Thermoplaste KW - Glasfaser PY - 1990 SN - 0023-5563 VL - 80 IS - 5 SP - 626 EP - 630 PB - Hanser CY - München AN - OPUS4-11996 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Boro, I. A1 - Augustin, G. A1 - Hampe, Andreas A1 - Hinrichsen, G. T1 - Fatigue Behaviour of High-Performance Fibre-Reinforced Composites with a Thermoplastic Matrix KW - Verbundwerkstoffe KW - Ermüdung KW - Biegeschwingung KW - Thermoplaste KW - Glasfaser PY - 1990 SN - 0723-0192 VL - 80 IS - 5 SP - 36 EP - 38 PB - Hanser CY - Munich AN - OPUS4-11999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Schulz, Eckhard T1 - The Fracture Process in the Interphase Investigated by the Single Fiber Pull-out Test T2 - Composites Testing and Standardisation ECCM-CTS 2 CY - Hamburg, Germany DA - 1994-09-13 PY - 1994 AN - OPUS4-12009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Marotzke, Christian A1 - Hampe, Andreas ED - Zarka, J. ED - Ohtmer, O. T1 - Finite Element Analysis of the Single Fiber Pull-Out Test T2 - Struceng and Femcad CY - Grenoble, France DA - 1990-10-17 KW - Composite Materials KW - Fiber Reinforced Plastics KW - Single Fiber Pull-Out Test KW - Interfacial Shear Stress KW - Finite-Element Method PY - 1991 SN - 2-907669-14-1 SP - 131 EP - 136 CY - Gournay-sur-Marne, France AN - OPUS4-6351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hampe, Andreas A1 - Mielke, Werner ED - Becker, Gerhard Wilhelm T1 - Relaxationsspektrometrie an Polymeren PY - 1973 SP - 261 EP - 264 PB - Bundesanstalt für Materialprüfung CY - Berlin AN - OPUS4-9628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian A1 - Meretz, S. A1 - Schulz, Eckhard T1 - Investigation of the Fracture Process in the Interphase/Interface T2 - Workshop "Interfaces in Carbon Fibre Reinforced Composites", Institut für Polymertechnik CY - Dresden, Germany DA - 1992-11-16 PY - 1992 AN - OPUS4-5900 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The toughness of the fiber/matrix interface measured by the single fibre pull-out test T2 - ICCI-VI - The Sixth International Conference on Composite Interfaces CY - Tel Aviv, Israel DA - 1996-05-05 PY - 1996 AN - OPUS4-5921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian A1 - Kalinka, Gerhard T1 - Mechanische Messungen der Bruchzähigkeit des Faser-Matrix-Grenzbereiches in polymeren Verbundwerkstoffen T2 - 35. Internationale Chemiefaser-Tagung CY - Dornbirn, Austria DA - 1996-09-25 PY - 1996 AN - OPUS4-5922 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Marotzke, Christian T1 - Comparison of the Interfacial Toughness Measured by the Single Fibre Pull-Out, the Indentation and the Fragmentation Test T2 - NIST, Workshop on Micro-Mechanics Measurement Technologies for Fiber-Polymer Interfaces CY - Gaithersburg, MD, USA DA - 1997-05-28 PY - 1997 AN - OPUS4-5928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian A1 - Kalinka, Gerhard T1 - Measurement of the Interfacial Toughness in Composites by Micromechanical Experiments T2 - 4th Arab International Conference on Polymer Science & Technology CY - Cairo, Egypt DA - 1997-09-08 PY - 1997 AN - OPUS4-5929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas T1 - Measurement and theoretical analysis of the interfacial toughness by micromechanical experiments T2 - Gordon Research Conference on Composites CY - Ventura, CA, USA DA - 1998-01-04 PY - 1998 AN - OPUS4-5938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Marotzke, Christian T1 - The Single Fibre Pull-Out Test Performed with a Microcomposite Sample T2 - The Seventh International Conference on Composite Interfaces - ICCI-VII CY - Fujisawa, Kanagawa, Japan DA - 1998-05-10 PY - 1998 AN - OPUS4-5940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian A1 - Brzezinka, Klaus-Werner A1 - Kalinka, Gerhard A1 - Schulz, Eckhard T1 - The Fracture Process in the Fibre/Matrix Interphase T2 - The Fifth International Conference on Composite Interfaces CY - Gothenburg, Sweden DA - 1994-07-20 PY - 1994 AN - OPUS4-5908 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Fracture Behaviour of the Fibre/Matrix Interphase T2 - Gorden Research Conference on Composites CY - Ventura, CA, USA DA - 1994-01-10 PY - 1994 AN - OPUS4-5909 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The fracture toughness of the glass fibre/polymer matrix interface: measurement and theoretical analysis T2 - 3rd International Conference on Deformation and Fracture of Composites CY - London, England DA - 1995-03-27 PY - 1995 AN - OPUS4-5914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Measurement of the energy release rate of fibre matrix interfaces T2 - IPCM4 CY - Eindhoven, Netherlands DA - 1995-09-11 PY - 1995 AN - OPUS4-5915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - The energy release rate of the fiber/polymer matrix interface: measurement and theoretical analysis T2 - 10th Technical Conference of the American Society for Composites CY - Santa Monica, CA, USA DA - 1995-10-18 PY - 1995 AN - OPUS4-5916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampe, Andreas A1 - Marotzke, Christian T1 - Fracture mechanics of the single fibre pull out experiment and measured energy release rates of fibre-matrix interfaces T2 - Workshop, Interfaces in glass, carbon and polymer fibre reinforced polymer composites CY - Kaiserslautern, Germany DA - 1995-02-01 PY - 1995 AN - OPUS4-5917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kallmann, Aribert A1 - Hampe, Andreas A1 - Rudolph, Hans-Volker T1 - Breitere Verwendung von umweltschonend hergestelltem Papier im Behördenbereich (Der Bundesminister des Innern, Umweltforschungsplan, Teikprogramm Abfallwirtschaft, Forschungsbericht 103 01 217) N2 - Anlaß der Untersuchungen waren die häufig vorgetragenen Vorbehalte gegen die Verwendung "umweltschonend hergestellter" Papiere - sog. Recycling-Papiere ("RC-Papiere") - im Behördenbereich. Drei verschiedene RC-Papier-Sorten wurden auf ihre Verwendbarkeit im erweiterten Bürobereich im Vergleich mit dort üblicherweise eingesetzten herkömmlichen Sorten untersucht, und zwar auf Eignung als Schreib-, Druck- und Kopierpapier sowie als Vorlage zum Kopieren, Fernkopieren und Mikroverfilmen. Ferner wurden die chemischen und physikalischen Kennwerte der Papiere ermittelt und das Verhalten bei künstlicher Alterung geprüft. Es konnte gezeigt werden, das RC-Papiere für die meisten Anwendungsfälle technisch durchaus geeignet sind. Bei besonderen Anforderungen - z.B. an die Lauf- oder Wiedergabeeigenschaften bei einzelnen Geräten oder Verfahren, an die mechanischen Eigenschaften oder an die Dauerhaftigkeit allgemein - sollten die Grenzen dieser Papiere beachtet werden. PY - 1981 SP - 1 EP - 132 PB - Bundesanstalt für Materialprüfung CY - Berlin AN - OPUS4-31969 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Schumacher, Klaus A1 - Severin, F. T1 - Werkstoffuntersuchung als Grundlage für den Bau eines taktilen Sensors PY - 1981 SN - 0044-3743 VL - 76 IS - 3 SP - 132 EP - 134 PB - Hanser CY - München AN - OPUS4-31868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -