TY - CHAP A1 - Hilpert, U. A1 - Härtig, F. A1 - Bartscher, M. A1 - Ehrig, Karsten A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Messunsicherheit, Kalibrierung und Normale zur zuverlässigen Rückführung der dimensionell messenden Computertomographie (CT) T2 - 4. VDI-Fachtagung Messunsicherheit - Messunsicherheit praxisgerecht bestimmen CY - Erfurt, Deutschland DA - 0208-11-12 PY - 2008 SN - 978-3-98-12624-1-4 IS - Kap. 31 SP - 1 EP - 14 CY - Düsseldorf AN - OPUS4-18600 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Bartscher, M. A1 - Goebbels, Jürgen A1 - Härtig, F. A1 - Kniel, K. A1 - Neukamm, M. A1 - Neuschaefer-Rube, U. A1 - Staude, Andreas ED - Denecke, M. ED - Walker, C. T1 - Dimensional control of micro components with synchrotron computed tomography T2 - 20th International congress on X-ray optics and microanalysis CY - Karlsruhe, Germany DA - 2009-09-14 KW - Synchrotron radiation KW - Computed tomography KW - Dimensional measurement KW - Micro components PY - 2010 SN - 978-0-7354-0764-0 SN - 0094-243X SP - 164 EP - 171 PB - American Institute of Physics AN - OPUS4-21293 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Neugebauer, M. A1 - Härtig, F. A1 - Goebbels, Jürgen A1 - Ehrig, Karsten A1 - Staude, Andreas T1 - Measurement of micro gears - comparison of optical, tactile-optical and CT-measurements N2 - Micro gears are applied in an increasing quantity in many applications. Therefore, precise measurements are of growing importance to ensure their quality. This contribution describes the measurement of gears of a micro planetary gear set with a tactile probe, a tactile-optical probe, an optical sensor, and computed tomography (CT). For the tactile measurements, a high precision piezoresistive microprobe was used. A so-called fiber probe was applied for tactile-optical measurements. This probe applies image processing to determine the position of the tactile probing element. For all tactile and tactile-optical measurements, single point probing was used. The optical measurements were carried out with an imaging sensor based on focus variation. Due to limited accessibility, on some gears not all regions could be measured by the optical sensor and the tactile-optical probe. In contrast to this, with CT the whole part could be measured with high point density. We used a micro-CT system and carried out measurements with Synchrotron-CT. All the sensors used deliver measurement data in Cartesian coordinates. It is a challenge to transfer these data into coordinates in which gear parameters are defined. For this, special attention must be paid to the determination of the gear axis and to the orientation of the teeth. The applied procedures are detailed for different micro gears. The comparison between data of different measurements was carried out successfully. The deviations between the CT data and the tactile or tactile-optical data lie in the range of only a few micrometers. KW - Micro gears KW - Coordinate metrology KW - Computed tomography KW - Optical sensors KW - Tactile probes PY - 2011 DO - https://doi.org/10.1117/12.872413 SN - 0277-786X SN - 0038-7355 SN - 0361-0748 N1 - Serientitel: Proceedings series – Series title: Proceedings series IS - 7864 SP - 78640H-1 EP - 78640H-9 PB - VDE-Verl. CY - Berlin ; Offenbach AN - OPUS4-25998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -