TY - CONF A1 - Gluth, Gregor T1 - RILEM TC 281-CCC WG6 - Carbonation of alkali-activated concrete: preliminary results N2 - Preliminary results of RILEM TC 281-CCC Working Group 6 'Carbonation of alkali-activated concrete' are presented. T2 - 74th RILEM Annual Week & 40th Cement and Concrete Science Conference CY - Online meeting DA - 31.08.2020 KW - Alkali-activated materials KW - Carbonation PY - 2020 AN - OPUS4-51199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Hillemeier, B. T1 - Pore structure and permeability of hardened calcium aluminate cement pastes of low w/c ratio N2 - The conversion of hydrated calcium aluminate cement (CAC) leads to an increase of its porosity which results in lower strength and higher permeability. Due to particular failures in the past, caused by conversion of CAC concretes, their use is sometimes considered to be not reliable. To evaluate the durability of converted CAC, pastes of two CACs were prepared at low w/c ratios (0.25 and 0.35), heated to 105 °C for 15 days and investigated by means of helium pycnometry, mercury porosimetry and nitrogen adsorption as well as by air permeability measurements. The results were compared to the pore structure properties and permeabilities of hardened Portland cement (OPC) pastes. At identical w/c, CAC pastes and OPC pastes exhibited similar open and total porosities. The threshold radii of the CAC pastes were about one order of magnitude greater while the hydraulic radii of their open pore system were smaller. The CAC pastes possessed somewhat smaller permeabilities than the OPC pastes and can thus be regarded as being as durable as the latter in this respect. From comparison of pore structure parameters and permeabilities it was furthermore concluded that significant pore structure damage occurs in the CAC pastes during mercury porosimetry measurements and therefore the measured threshold radii have to be considered as unreliable. KW - Calcium aluminate cement KW - Permeability KW - Porosity KW - Pore structure KW - Mercury porosimetry KW - Threshold radius KW - Tonerdezement KW - Permeabilität KW - Porenstruktur KW - Quecksilberdruckporosimetrie PY - 2013 UR - http://link.springer.com/article/10.1617/s11527-012-9991-2/fulltext.html DO - https://doi.org/10.1617/s11527-012-9991-2 SN - 1359-5997 SN - 1871-6873 VL - 46 IS - 9 SP - 1497 EP - 1506 PB - Springer CY - Dordrecht AN - OPUS4-28598 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Greiser, Sebastian A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Hunger, M. A1 - Jäger, Christian T1 - Differentiation of the solid-state NMR signals of gel, zeolite phases and water species in geopolymer-zeolite composites N2 - Geopolymer-zeolite composites were synthesized using a silica-rich industrial byproduct from chlorosilane production and sodium aluminate. Pastes were cured at 80 °C and 80% RH, and subsequently dried in two different climates: at 23 °C and 50% RH, and under vacuum. 1H MAS, 23Na MAS and 29Si MAS NMR and XRD measurements were performed after the drying procedures as well as after subsequent aging. Zeolite Na-A was found beside traces of faujasite-type zeolite and zeolite EMT as major crystalline phases in the cured composites; the fraction of geopolymeric gel in the reaction products was determined to be ~18% on a molar basis. Various water species could be distinguished using 1H MAS and 1H-29Si CP MAS NMR, applying rotorsynchronized echo experiments. The largest fraction of the pore water resides in the α-cages of the zeolite Na-A and in the geopolymeric gel; in addition, water exists in the β-cages of the zeolites and adsorbed at sodium ions. The water species in α-cages and in the pores of the geopolymeric gel exhibit slightly different chemical shifts of 4.7 ppm and 4.9 ppm, respectively, in the 1H MAS NMR spectra. Changes of the water content in the geopolymer pores of differently dried samples were observed and led to slightly varied chemical shifts in the 29Si MAS NMR spectra too. Measurements after more than 500 days revealed no significant aging effects of the composites, which confirm their chemical stability. KW - Geopolymers KW - Aluminosilicate inorganic polymers KW - Zeolite Na-A KW - Spectroscopy KW - Drying PY - 2017 DO - https://doi.org/10.1016/j.ceramint.2016.11.004 SN - 0272-8842 VL - 43 IS - 2 SP - 2202 EP - 2208 PB - Elsevier AN - OPUS4-38694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Greiser, Sebastian A1 - Gluth, Gregor A1 - Sturm, Patrick A1 - Brouwers, H.J.H. A1 - Jäger, Christian ED - Bílek, V. ED - Kersner, Z. T1 - 27Al-1H and 27Al-29Si Double resonance NMR of one-part geopolymers N2 - The production and processing of ordinary Portland cement are responsible for nearly 5% of the world C02 emissions. Due to the world’s increasing requirement for building materials, this air pollution is growing up in the next decades. Alternative cement such as geopolymers can reduce these emissions effectively, Conventional geopolymer binders, produced ffom fly ash or metakaolin as aluminosilicate source and water-glass or alkali hydroxide Solutions as activator, are often used and studied. It is known that under appropriate conditions the starting materials form a three-dimensional aluminosilicate structure and create a gel-like matrix, In our case, a silica source from wastewater treatment of chlorosilane production and solid sodium aluminate as starting materials are initiated to harden by water. This procedure is known as “just add water” or “one-part” geopolymer formulation. These composites have significant advantages for use on construction site, but their Chemical structure is not extensively analyzed. In this work, a well known one-part geopolymer is investigated by 'H and 27A1 magic-angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy. Furthermore, it is shown that overlapping NMR lines can resolved with echo experiments and T2 - NTCC2014 - International conference on non-traditional cement and concrete CY - Brno, Czech Republic DA - 16.06.2014 KW - Geopolymers KW - One-part formulation KW - Zeolite Na-A KW - NMR KW - REDOR PY - 2014 SN - 978-80-214-4867-4 SP - 91 EP - 94 PB - Novpress AN - OPUS4-31224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Bernal, S. A. T1 - RILEM TC CUC: Carbon dioxide uptake by concrete during and after service life – Opening Letter N2 - The ability of cement to chemically bind CO2 in a carbonation reaction enables the material to act as a carbon sink, which could partly account for offsetting the CO2 emissions associated with cement production. In response to the many open questions in this context, the RILEM Technical Committee CUC was created in May 2024. The focus of the TC will be to facilitate discussions regarding the current approaches to estimate the CO2 uptake by cementitious materials (concrete and other construction products) during and after service life. This Opening Letter presents aspects of the motivation to establish the TC, a brief overview of the state of the art in the field, the scheduled work programme, and the anticipated impact of the TC outputs. Though it is not intended to be an exhaustive discussion of the challenges to be addressed, from what is summarized in this letter, it is clear that work is required to base estimates of CO2 uptake by cementitious materials on a data set that is as extensive, accurate and forward-looking as possible. It is anticipated that the inclusion of interdisciplinary perspectives and data from academia and industry will enable progress in the field. KW - Cement KW - Concrete KW - Recarbonation KW - Carbon dioxide uptake KW - Carbonation rate PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623724 DO - https://doi.org/10.21809/rilemtechlett.2024.208 SN - 2518-0231 VL - 9 SP - 61 EP - 67 PB - RILEM AN - OPUS4-62372 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Dauerhaftigkeit von Betonen auf Basis klimafreundlicher Bindemittel N2 - Aus Gründen des Klimaschutzes werden in den kommenden Jahren mehr Zemente mit verringertem Klinkerfaktor und alternative Bindemittel (klimafreundliche Bindemittel) zum Einsatz kommen. Für ihre sichere und zuverlässige Verwendung ist ein umfangreiches Verständnis der Einflüsse auf die Dauerhaftigkeit der aus ihnen hergestellten Betone notwendig. Der vorliegende Beitrag gibt einen kurzen Überblick über einige jüngere Entwicklungen und Forschungsergebnisse auf dem Gebiet. Der Fokus liegt auf Ergebnissen der Arbeiten von Technischen Komitees der RILEM sowie der EFC und eigenen Forschungsergebnissen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Klimafreundliche Bindemittel KW - Betone PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612872 SN - 978-3-9818564-7-7 SP - 22 EP - 29 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sittner, Jonathan A1 - Hoffmann, T. A1 - Bertmer, M. A1 - Neubert, M. A1 - Schuster, T. A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Optimizing calcination methods towards a more sustainable production of calcined clays N2 - Calcined clays are emerging as sustainable alternatives for cement production due to their potential to reduce carbon footprint and energy consumption. This study investigates the calcination of low-grade kaolinitic clays, using rotary kiln and fluidized bed. The calcined clays from the rotary kiln showed enhanced performance in the cement paste. The fluidized bed method demonstrated the potential for significant energy savings, achieving near-complete dehydroxylation with just 30 minutes of calcination. These findings highlight the promise of fluidized bed calcination for efficient clay activation, though further optimization is needed. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Calcination methods KW - Optimizing KW - Blended cement pastes KW - XRD results KW - Thermogravimetric analysis (TGA) PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612891 SN - 978-3-9818564-7-7 SP - 37 EP - 45 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Alkalisch aktivierte Bindemittel mit hohem Säurewiderstand für die Kanalsanierung N2 - Die biogene Schwefelsäurekorrosion (BSK) von Betonbauteilen in Abwassersystemen verursacht weltweit hohen Reparaturbedarf. Um zukünftigen Reparaturbedarf zu minimieren, werden für Neubau- und Sanierungsmaßnahmen z. T. Materialien mit besonders hohem Widerstand gegen BSK benötigt. Der vorliegende Beitrag beschreibt Forschungen zu alkalisch aktivierten Bindemitteln, die bei geeigneter Formulierung einen hohen Widerstand gegen BSK bzw. Säureangriff aufweisen. Zusätzlich werden jüngste Fortschritte bei der Bewertung von Methoden zur Prüfung des Widerstands gegen BSK dargestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Säurewiderstand KW - Betonbauteile KW - Abwassersystemen PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613141 SN - 978-3-9818564-7-7 SP - 90 EP - 93 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Greiser, Sebastian A1 - Gluth, Gregor A1 - Sturm, Patrick A1 - Jäger, Christian T1 - Correction: 29Si{27Al}, 27Al{29Si} and 27Al{1H} double-resonance NMR spectroscopy study of cementitious sodium aluminosilicate gels (geopolymers) and gel–zeolite composites N2 - Correction for ‘29Si{27Al}, 27Al{29Si} and 27Al{1H} double-resonance NMR spectroscopy study of cementitious sodium aluminosilicate gels (geopolymers) and gel–zeolite composites’ by Sebastian Greiser et al., RSC Adv., 2018, 8, 40164–40171, https://doi.org/10.1039/C8RA09246J. PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-635365 DO - https://doi.org/10.1039/d3ra90078a SN - 2046-2069 VL - 13 IS - 37 SP - 26148 PB - Royal Society of Chemistry (RSC) CY - London AN - OPUS4-63536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nikoonasab, Ali A1 - Müller, Thoralf A1 - Licht, M. A1 - Raupach, M. A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Sulfides in the pore solutions of GGBFS-containing concretes - Influence on the corrosion of reinforcing steel N2 - Steel corrosion in sulfide-containing solutions is a challenge in various environments, such as reinforced concrete structures. In concrete, sulfides are introduced by ground granulated blast-furnace slag (GGBFS), used in standard cements and alkali-activated materials (AAMs), affecting steel corrosion. This study examined steel in synthetic GGBFS-containing cement pore solutions using electrochemical techniques. Compared to Portland cement solutions, steel in sulfide-containing solutions exhibits lower open circuit potentials and polarisation resistances. Thus, Portland cement concrete corrosion assessment standards are unsuitable for GGBFScontaining concrete. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Corrosion KW - Reinforcing steel PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612963 SN - 978-3-9818564-7-7 SP - 55 EP - 59 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Law, D. W. A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Gunasekara, C. A1 - Yamchelou, M. T. ED - Banthia, N. ED - Soleimani-Dashtaki, S. ED - Mindess, S. T1 - Characteristics of high calcium fly ash geopolymer mortar N2 - Portland cement is one of the principal sources of anthropomorphic CO2 emissions. It is estimated that cement production contributes up to 10% of greenhouse gas emissions and annual cement production over 4 billion tons. This has led to the development of a range of alkali activated materials (AAM), the most common precursor materials being class F fly ash and blast furnace slag. At present Class C Fly Ash is not widely utilized as an AAM due to the chemical composition and activation requirements. However, initial research on high Calcium German Class C Fly Ash suggests that the material may have potential for application as an AAM. This paper reports the development of ambient cured alkali activated mortar optimised by varying the alkali modulus and w/b ratio. The evolution of the mechanical and microstructural properties is reported over the initial 28 day period. Compressive strength in excess of 10 MPa at 7 days and 15 MPa at 28 days was achieved at ambient temperature. Similar strengths were observed for both 10% and 15% dosage but as dosage increases the optimal Alkali Modulus reduces. T2 - 77th RILEM Annual Week and the 1st Interdisciplinary Symposium on Smart & Sustainable Infrastructures (ISSSI 2023) CY - Vancouver, BC, Canada DA - 04.09.2023 KW - Alkali-activated materials KW - Brown Coal Fly Ash KW - Lignite Coal PY - 2024 SN - 978-3-031-53388-4 SN - 978-3-031-53389-1 DO - https://doi.org/10.1007/978-3-031-53389-1_8 SN - 2211-0844 SN - 2211-0852 VL - 48 SP - 82 EP - 92 PB - Springer CY - Cham AN - OPUS4-59578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nikoonasab, Ali A1 - Licht, M. A1 - Weiler, L. A1 - Achenbach, R. A1 - Raupach, M. A1 - Gluth, Gregor T1 - Pore Solution composition of GGBFS-containing cement pastes N2 - Ground Granulated Blast-Furnace Slag (GGBFS), a by-product of the iron-making process, has gained significant attention as a supplementary cementitious material and has become increasingly popular in recent years due to its remarkable properties. GGBFS can significantly reduce the environmental impact of cement production when it comes to building concrete structures. GGBFS can either be blended with ordinary Portland cement (OPC) (up to a 90% replacement), or it can be used in the production of alkali-activated materials (AAMs). However, a comprehensive understanding of the pore solution composition is necessary for understanding various aspects of cementitious materials and their durability, including corrosion behavior, passivation of steel, and resistance to deteriorative processes. In the present work, the pore solutions of seven different GGBFS-containing cements (alkali-activated slag, alkali-activated slag/fly ash blends, a hybrid alkaline cement, CEM III/C, and CEM III/B) were extracted and analysed by inductively coupled plasma-optical emission spectroscopy, ion chromatography, pH, redox potential, and conductivity measurements. For comparison, a Portland cement pore solution was analysed similarly. The Concentrations of reduced sulfur were noteworthy in all GGBFS-containing cements, particularly in alkali-activated cements, where concentrations were notably higher compared to standard cements. The redox potentials of the pore solutions were primarily dictated by the concentrations of reduced sulfur, although other factors may contribute. Additionally, sulfur species in the pore solutions had an impact on pH, electrical conductivity, and other properties pertinent to the corrosion of reinforcements. T2 - RILEM Spring Convention 2024 & Conference on Advanced Construction Materials and Processes for a Carbon Neutral Society CY - Milan, Italy DA - 10.04.2024 KW - GGBFS KW - AAM KW - Sulfide KW - Pore solution composition KW - Redox potential PY - 2024 AN - OPUS4-59960 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rickard, William A1 - Gluth, Gregor A1 - Pistol, Klaus T1 - In-situ thermo-mechanical testing of fly ash geopolymer concretes made with quartz and expanded clay aggregates N2 - The mechanical and microstructural properties of geopolymer concretes were assessed before, during and after high temperature exposure in order to better understand the engineering properties of the material. Fly ash based geopolymer concretes with either quartz aggregate or expanded clay aggregate were exposed to various temperatures up to 750 °C using a thermo-mechanical testing apparatus. Microstructural investigations were also undertaken to better understand the measured changes in the mechanical properties. It was found that dehydration of capillary water caused cracking and strength losses at temperatures ≤300 °C, an effect that was more severe in the quartz aggregate geopolymer due to its lower permeability. At higher temperatures (T ≥ 500 °C) sintering promoted strength increases which enabled both concrete types to yield significant strength advantages over conventional materials. Stress–mechanical strain curves, which form the basis of the fire design of concrete structures, are reported. KW - Temperature KW - Microstructure KW - Physical properties KW - Alkali activated cement KW - Geopolymers KW - Transient thermal creep PY - 2016 DO - https://doi.org/10.1016/j.cemconres.2015.11.006 SN - 0008-8846 SN - 1873-3948 VL - 80 SP - 33 EP - 43 PB - Pergamon Press CY - New York, NY AN - OPUS4-35080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Nanjie A1 - Hüsken, Götz A1 - Gluth, Gregor A1 - Kühne, Hans-Carsten T1 - The influence of activator composition on the strength, shrinkage and chloride migration resistance of alkali-activated slag mortars N2 - Alkali-activated slag materials are known for their high Chloride penetration resistance. This makes them potentially applicable as repair systems for damaged steel-reinforced concrete structures, which are exposed to chloride attack. For this purpose, the influence of the activator composition, i.e. the SiO2 and Na2O concentration of the alkaline solution on a) the compressive strength, b) shrinkage and mass change and c) the resistance against chloride penetration of four alkali-activated slag mortars (AASM) were studied. An ordinary Portland cement-based mortar was used as the reference sample. Increasing SiO2 and Na2O concentrations increased the strength, shrinkage and mass loss of the AASMs. The resistance of the mortars against chloride penetration was evaluated using the non-steady-state migration coefficient Dnssm obtained from NT BUILD 492. The results indicate that the Dnssm is related to differences in the pore solution of the AASMs rather than to differences in their microstructure. An upcoming study of the authors is going to evaluate this hypothesis by the accelerated chloride penetration (diffusion) test. T2 - 6th International Conference Non-Traditional Cement and Concrete 2017 CY - Brno, Czech Republic DA - 19.06.2017 KW - Alkali-activated slag mortar KW - Strength KW - Shrinkage KW - Chloride migration coefficient PY - 2018 DO - https://doi.org/10.4028/www.scientific.net/KEM.761.61 SN - 1662-9795 VL - 761 SP - 61 EP - 64 PB - Trans Tech Publications CY - Switzerland AN - OPUS4-43884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten ED - Ludwig, H.-M. T1 - Structural investigations on one-part geopolymers with different chemical composition N2 - Geopolymers are promising alkali activated materials with a wide range of possible applications like heat-resistant coatings and adhesives or concretes with lower C02 emissions than conventional Portland cement-based systems. Conventional ("two-part") geopolymers are synthesized by an activation of aluminosilicate feedstocks like metakaolin or blast furnace slags with highly alkaline solutions like sodium hydroxide solutions and/or water glass solutions. A more recent approach are so called one-part geopolymers, where the alkaline activator is provided in solid form, so that only water has to be added to initiate the geopolymerisation reaction. The handling of alkaline solutions is avoided, which possesses several advantages compared to conventional geopolymers, in particular regarding safety and health issues, and, thus, it improves economic and social acceptance of these binders. However, the new formulations are less exhaustively studied and the knowledge about conventional geopolymers cannot simply be transferred to this new class of binders. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Geopolymers KW - One-part mix PY - 2015 SN - 978-3-00-050225-5 VL - 2 SP - P1.77, 2-857 - 2-864 AN - OPUS4-34880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Watolla, Marie-Bernadette A1 - Gluth, Gregor A1 - Sturm, Patrick A1 - Rickard, W.D.A. A1 - Krüger, Simone A1 - Schartel, Bernhard T1 - Intumescent geopolymer-bound coatings for fire protection of steel N2 - The passive fire protection of steel structures and other load-bearing components will continue to gain importance in future years. In the present contribution, novel intumescent aluminosilicate (geopolymer-bound) composites are proposed as fire-protective coatings on steel. Steel plates coated with these materials were exposed to the standard temperature-time curve as defined in ISO 834 – 1:1999. The coatings partially foamed during curing and expanded further during thermal exposure, demonstrating their intumescent characteristic.Thermogravimetryandoscillatory rheometry determined that the intumescent behavior is attributed to a transition to a viscous state (loss factor > 1) in the temperature range of major water release, differing from conventional geopolymers. XRD and SEM images showed that the coatings had characteristics of ceramic or glass-ceramic foams after fire resistance testing, suggesting superior performance under challenging conditions. The thickness of the coatings influenced their foaming and intumescent behavior and thus the time for the coated steel plates to reach 500 °C. A number of additives were also studied with the best performance obtained from samples containing sodium tetraborate.Acoating of just 6mmwas able to delay the time it takes for a steel substrate to reach 500 °C to more than 30 minutes. KW - Geopolymers KW - Fire protection KW - Intumescence KW - Coatings KW - Fire resistance PY - 2017 UR - https://www.ceramic-science.com/articles/all-articles.html?article_id=100558 DO - https://doi.org/10.4416/JCST2017-00035 VL - 8 IS - 3 (Topical issue: Geopolymers) SP - 351 EP - 364 PB - Göller Verlag CY - Baden-Baden AN - OPUS4-42139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten T1 - Synthesizing one-part geopolymers from rice husk ash N2 - One-part geopolymers offer advantages over conventional geopolymers with regard to handling and storage of feedstocks. However, they often suffer from a low degree of reaction, a high amount of crystalline byproducts, and consequently low strength. In this study, one-part geopolymers were produced from rice husk ash (RHA) and sodium aluminate, and investigated by XRD, ATR-FTIR, SEM and compressive strength testing. The compressive strength of the material was 30 MPa, i.e. significantly higher than for comparable one-part geopolymers. This is attributed to an almost complete reaction of the RHA and the absence of crystalline byproducts (zeolites) in the hardened geopolymer. KW - Alkali-activation KW - Geopolymers KW - One-part formulation KW - Bio-based materials KW - Rice husk ash PY - 2016 DO - https://doi.org/10.1016/j.conbuildmat.2016.08.017 SN - 0950-0618 VL - 124 SP - 961 EP - 966 PB - Elsevier Ltd. AN - OPUS4-37226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Gluth, Gregor A1 - Oppat, Klaus A1 - Kühne, Hans-Carsten ED - Christ, H.-J. T1 - Charakterisierung von Bauteiloberflächen mittels laserbasierter Rauigkeitsmessung T1 - Characterization of component surfaces by means of laser-based roughness measurement N2 - Die Charakterisierung von Oberflächen mittels optischer Technologien wird dank des ständigen Fortschritts bei der Entwicklung von Sensoren und Lichtquellen immer attraktiver. Die kommerziell erhältlichen Systeme werden dabei immer leistungsstarker, empfindlicher und genauer. Mit diesen Systemen ist es möglich, viele hundert Messpunkte innerhalb weniger Sekunden zu erfassen und auszuwerten. Dieser Fortschritt führt auch im Baubereich zu einer ständigen Weiterentwicklung und Verbesserung von Messmethoden und Systemen. So werden bereits standardisierte und angewandte Messprinzipien weiterentwickelt, den neuen Möglichkeiten angepasst und deren Anwendung auf neue Bereiche ausgeweitet. An der BAM ist es gelungen ein Messsystem zu entwickeln, mit dem Rautiefen von Bauteiloberflächen in Anlehnung an bereits standardisierte Verfahren bestimmt werden können. Mit dem Mer vorgestellten System können sowohl horizontale als auch vertikale, gewölbte und geneigte Oberflächen untersucht werden. Dank der Implementierung geeigneter Algorithmen entsprechen die vom System ausgegebenen Ergebnisse denen der seit Jahrzehnten mit den volumetrischen Messverfahren erzielten Ergebnisse. Vor allem bei der Instandsetzung von Bauwerken bringt das an der BAM entwickelte System erhebliche Vorteile, da es zukünftig auch möglich sein wird Wände und Decken genauer zu untersuchen. N2 - The characterization of surfaces by using optical technologies is becoming increasingly attractive. The reason therefore is the constant progress in the development of sensors and light sources. Commercially available systems are becoming increasingly powerful, more sensitive and accurate. With these systems it is possible to detect several hundred measurement points within a few seconds and evaluated them subsequently. This progress also carries out in the field of construction to a continually development and improvement of measurement methods and systems. So it is possible to further developed already standardized and applied measurement principles, adapt them to new opportunities and expand the application of these principles to new areas. At BAM a new measurement system has been developed for determine the roughness of component surfaces in accordance with standardized procedures. The system presented can be used on horizontal and vertical oriented, inclined and curved surfaces. By implementing appropriate algorithms the system determined results which correspond to the results of the volumetric measurement methods. Especially for the field of repair systems this measurement system brings significant advantages. In future it will also be possible to examine walls and ceilings in detail which is not possible until now. T2 - Tagung Werkstoffprüfung 2013 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Neu-Ulm, Germany DA - 28.11.2013 KW - Oberflächencharakterisierung KW - Rauigkeit KW - Optische Messtechnik KW - Lasertriangulation KW - Surface characterization KW - Surface roughness KW - Optical measurement techniques KW - Laser triangulation PY - 2013 SN - 978-3-514-00806-9 SP - 291 EP - 296 PB - Verlag Stahleisen CY - Düsseldorf AN - OPUS4-29989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Sittner, Jonathan A1 - Asante, Bright A1 - Nikoonasab, Ali A1 - Ebell, Gino T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 1: Chemie der Bindemittel N2 - Aus Gründen des Klimaschutzes werden in den kommenden Jahren mehr Zemente mit verringertem Klinkerfaktor und alternative Bindemittel (klimafreundliche Bindemittel) zum Einsatz kommen. Für ihre sichere und zuverlässige Verwendung ist ein umfangreiches Verständnis der Einflüsse auf die Dauerhaftigkeit der aus ihnen hergestellten Betone notwendig. In jüngerer Zeit sind hierzu insbesondere von Technischen Komitees in RILEM und in der EFC neue Erkenntnisse gewonnen worden, die im Rahmen des 63. DAfStb-Forschungskolloquiums an der BAM (Tagungsband: DOI 10.26272/opus4-61338) im Zusammenhang mit den Beiträgen der BAM zu diesen Ergebnissen vorgestellt wurden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Zement KW - Bindemittel KW - Dauerhaftigkeit KW - Beton PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 129 EP - 131 PB - concrete content UG CY - Schermbeck AN - OPUS4-63066 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Corrosion of steel reinforcement in geopolymer mortars - carbonation resistance, chloride migration, and preliminary corrosion potential data N2 - Alkali-activated materials such as geopolymers are currently receiving a lot of attention because of their potential to be used as binders for concrete with advantageous engineering properties and reduced manufacturing CO2 emissions. Knowledge of the durability of steel in these concretes and related properties of alkali-activated materials is a prerequisite for their application as building materials, if they are to be used for steel reinforced elements. However, to date only limited data exists on this topic. The present contribution focuses on durability-related transport properties of geopolymer-based mortars (as model systems for concrete). We report results of accelerated carbonation, rapid chloride migration (RCM) and air permeability measurements as well as porosity data for fly ash-based geopolymer mortars, including mixes containing ground granulated blast furnace slag (GGBFS). In addition, we report polarization resistance data and corrosion potential vs. time curves for carbon steel bars embedded in two of the fly ash-based geopolymer mortars and a CEM I-based mortar (as reference). Despite comparable total porosities, the carbonation depths, the chloride migration coefficients and the air permeabilities of the mortars differed significantly. In general, the addition of GGBFS to the binders improved the performance (decreased transport coefficients); however, this was not found to be true for the air permeability in all cases. This latter effect can be explained by drying damage of the C-(A-)S-H gel in GGBFS-containing binders. On the other hand, low transport coefficients can also be achieved by optimization of the binder formulation without the addition of GGBFS, which is also reflected in the material’s air permeability. Thus, there exists no simple correlation between air permeability (of harshly dried mortars) and durability-related transport coefficients for the studied alkali-activated materials. The corrosion potential vs. time curves in combination with polarization resistance values reveal that the steel reinforcement in geopolymer mortars assumed a passive state. However, this happened considerably later than for steel in CEM I-based mortars. The free corrosion potential of carbon steel reinforcement in the geopolymer mortars had different values than the free corrosion potential values for the CEM I-based mortar for both the active and the passive state; possible reasons for this behavior are discussed. T2 - EUROCORR 2017 CY - Prague, Czech Republic DA - 03.09.2017 KW - Geopolymers KW - Alkali-activated materials KW - Corrosion KW - Steel reinforcement KW - Concrete PY - 2017 AN - OPUS4-41869 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Geopolymerization of a silica residue from waste treatment of chlorosilane production N2 - A silica residue from waste treatment of chlorosilane production was used together with solid sodium aluminate to test its applicability for the production of one-part geopolymers. The blend was activated with water and cured at 70 °C. The degree of reaction and strength were determined after 1, 3, and 7 days. The reaction products were analyzed by XRD and SEM/EDX. Until the third day of curing the degree of reaction of the residue reached 51 % and the strength was 8.9 MPa. The reaction product was identified as geopolymer containing zeolite A. Thus, the results confirmed that the residue may be used in the production of geopolymers. However, after 3 days of curing no further progress of reaction was observed and the strength slightly decreased, which was attributed to changes in the structure of the geopolymeric gel. It was further observed that even harsh vacuum drying left some water (presumably zeolitic water and surface hydroxyl groups) in the geopolymer. KW - Geopolymers KW - One-part formulation KW - Silica KW - Zeolite A PY - 2013 UR - http://link.springer.com/article/10.1617/s11527-012-9972-5/fulltext.html DO - https://doi.org/10.1617/s11527-012-9972-5 SN - 1359-5997 SN - 1871-6873 VL - 46 IS - 8 SP - 1291 EP - 1298 PB - Springer CY - Dordrecht AN - OPUS4-28596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Microbially induced corrosion of cementitious materials in sewer systems N2 - Sewer networks (also called wastewater systems) include structures to collect and transport wastewater to disposal or treatment in dedicated facilities. These networks are essential infrastructures of our societies, and the size of these systems in terms of length as well as asset value is usually vast. Accordingly, the annual rehabilitation and replacement costs for sewer networks are very high in many countries. In addition, failures of wastewater systems can cause severe health and environmental problems, making the durability of these infrastructures an issue of crucial societal importance. A substantial fraction of the deterioration of sewers is caused by microbially influenced corrosion (MIC) of concrete structures in the networks, and, thus, understanding the causes of this process is crucial to be able to effectively direct resources for rehabilitation, replacement and construction of sewer systems. Because of the importance of the problem, it has been studied for many decades, and significant progress has been made during this time. In recent years, answers to several previously underexplored questions, for example regarding the validity of the different test methods to assess the resistance of cementitious materials against MIC and the suitability of new cementitious materials for sewer repair, have begun to emerge. The present contribution gives an overview over the processes involved in MIC of cementitious materials in sewers, and reviews recent findings concerning the resistance of cementitious materials against MIC. The data indicate that alkali-activated materials can exhibit exceptionally high resistance against MIC, while it is presently not fully understood which mix design parameters deter¬mine this resistance. Disagreement exists in the literature regarding the causes of the generally high resistance of calcium aluminate cements. Significant progress has been made in determining the deterioration rate of cementitious materials under strongly corroding conditions, but well-founded approaches to classify the severity of MIC attack in sewers seem not to be available at present. T2 - MICxUS 2025 – Symposium on Microbiologically Influenced Corrosion (MIC) in Industrial and Utility Systems CY - Nicosia, Cyprus DA - 21.01.2025 KW - MIC KW - Cement KW - Repair mortar KW - Sulfuric acid KW - Sewers PY - 2025 AN - OPUS4-62738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Corrosion of steel in geopolymer mortars N2 - The contribution reports on durability-related transport properties of geopolymer-based mortars. We show results of accelerated carbonation, rapid chloride migration (RCM), accelerated chloride diffusion, and air permeability measurements for fly ash-based geopolymer mortars, including mixes containing ground granulated blast furnace slag (GGBFS). In addition, we report polarization resistance data and corrosion potential vs. time curves for carbon steel bars embedded in two of the fly ash-based geopolymer mortars and a CEM I-based mortar (as reference). Despite comparable total porosities, the carbonation depths, the chloride migration coefficients and the air permeabilities of the mortars differed significantly. In general, the addition of GGBFS to the binders improved the performance (decreased transport coefficients); however, this was not found to be true for the air permeability in all cases. This latter effect can be explained by drying damage of the C-(A-)S-H gel in GGBFS-containing binders. On the other hand, low transport coefficients can also be achieved by optimization of the binder formulation without the addition of GGBFS, which is also reflected in the material’s air permeability. The corrosion potential vs. time curves in combination with polarization resistance values reveal that the steel reinforcement in geopolymer mortars assumed a passive state. However, this happened considerably later than for steel in CEM I-based mortars. The free corrosion potential of carbon steel reinforcement in the geopolymer mortars had different values than the free corrosion potential values for the CEM I-based mortar for both the active and the passive state. T2 - International Workshop on Alkali-Activated Materials CY - Ljubljana, Slovenia DA - 11.05.2017 KW - Geopolymers KW - Alkali-activated materials KW - Reinforcement corrosion KW - Carbonation KW - Chloride ingress PY - 2017 AN - OPUS4-40241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogler, Nico A1 - Gluth, Gregor A1 - Oppat, Klaus A1 - Kühne, Hans-Carsten T1 - Charakterisierung von Bauteiloberflächen – Rautiefebestimmung mittels konventioneller und laserbasierter Verfahren T1 - Surface characterization of building elements - roughness measurements by conventional and laser-based methods N2 - Die Bestimmung der Rauheit von Bauteiloberflächen stellt eine wichtige Messaufgabe im Bauwesen dar. Vor allem bei der Betoninstandsetzung, im Straßenbau und bei der Herstellung von Stahlbeton-Halbfertigteilen ist die Rauheit – gemessen als Rautiefe – eine wichtige Kenngröße. Zurzeit werden Messungen der Rautiefe mittels volumetrischer Verfahren (Sandflächenverfahren) durchgeführt. Diese bereits seit mehreren Jahrzehnten angewandten Verfahren sind jedoch auf horizontale bzw. wenig geneigte und trockene Oberflächen beschränkt. Darüber hinaus hängen die erzielten Ergebnisse sehr stark von der angewandten Prüfvorschrift, den darin vorgeschriebenen Prüfmitteln und Geräten und dem jeweiligen Anwender ab. Als Alternative zu den volumetrischen Verfahren wurde an der Bundesanstalt für Materialforschung und -prüfung (BAM) ein automatisiertes, laserbasiertes Messverfahren entwickelt, mit dem Rautiefen von Bauteiloberflächen in Anlehnung an bereits standardisierte Verfahren bestimmt werden können. Der vorliegende Beitrag befasst sich zunächst mit den konventionellen Prüfverfahren, beschreibt die wichtigsten Zusammenhänge und zeigt die Grenzen dieser Methoden auf. Im zweiten Teil wird das an der BAM entwickeltes Messsystem, als zielführendes Alternativverfahren für die konventionellen Methoden, vorgestellt und dessen Leistungsfähigkeit näher beschrieben. N2 - The measurement of surface roughness of building elements is an important task in civil engineering, particularly in the field of concrete repair, in road construction and in the production of precast concrete elements. At present, the surface roughness is generally determined by the so called sand-patch-test (volumetric method). This method which is used since several decades is only applicable on horizontal or only slightly sloped and dry surfaces. In addition, the results strongly depend on the utilised standards, the prescribed test equipment and the executing person. Therefore, a laser-based device for the determination of surface roughness has been developed at Bundesanstalt fur Materialforschung und -pru-fung (BAM). This contribution deals first with the different modifications of the sand-patch-test and other conventional methods, and describes the underlying formulae and the limitations of the methods. In the second part, the laser-based system which was developed at BAM is presented; its advantages and the capability of this alternative method will be described in detail. KW - Rautiefe KW - Instandsetzung KW - Laserbasierte Rautiefebestimmung KW - Shear PY - 2017 SN - 0005-6650 VL - 92 IS - März SP - 97 EP - 104 PB - Springer VDI CY - Düsseldorf AN - OPUS4-39299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Winkler, Juliette A1 - Beck, M. A1 - Gluth, Gregor ED - Schneider, F. ED - Hehl, K. ED - Heyde, S. T1 - Kurz- und mittelfristige Verbundfestigkeit von alkaliaktivierten Mörteln auf Beton N2 - Ein zentrales Fundament moderner Gesellschaften ist eine intakte Abwasserinfrastruktur. Schäden infolge biogener Schwefelsäurekorrosion von konventionellen Betonen haben jedoch zu einem erheblichen Sanierungsbedarf geführt. Alkaliaktivierte Mörtel besitzen aufgrund eines hohen Säurewiderstands das Potential, einen Beitrag zur langfristigen Lösung dieses Problems zu leisten. Dazu müssen jedoch zunächst die Faktoren, die den Haftverbund zwischen diesen Mörteln und dem Betonsubstrat bestimmen, besser verstanden werden, um die Eigenschaften der Beschichtungssysteme gezielt anpassen und verbessern zu können. Die vorliegende Arbeit liefert hierzu einen Beitrag und zeigt dadurch Wege zu einer technisch machbaren und nachhaltigen Sanierung von Abwasserbauwerken auf. KW - Alkalisch aktivierte Bindemittel KW - Abwassersysteme KW - Reparatursysteme KW - Verbund KW - Dauerhaftigkeit PY - 2022 SN - 978-3-8440-8818-2 SP - 89 EP - 100 CY - Berlin AN - OPUS4-57701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Vergleich unterschiedlicher Verfahren zur Messung der Oberflächenrauheit T2 - 7. Internationales Kolloquium Industrieböden CY - Ostfildern, Germany DA - 2010-12-14 PY - 2010 AN - OPUS4-22795 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - LightSHIP II - Inorganic Binder System for Innovative Panel Technology in East Africa T2 - Africa Re:Load/Discover new opportunities for innovation and business, öffentlicher Workshop CY - Weimar, Germany DA - 2011-08-29 PY - 2011 AN - OPUS4-24471 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Vogler, Nico A1 - Gardei, André A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Laserbasiertes Messverfahren zur Rautiefe-Bestimmung T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Rauheit KW - Rautiefe KW - Volumetrische Methode KW - Sandflächenverfahren KW - Laserverfahren KW - Linienlaser PY - 2011 SN - 978-3-9814281-0-0 SP - 256 EP - 261 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - LightSHIP II: Inorganic Binder Systems for Innovative Panel Technology in East Africa T2 - Workshop Cement and Concrete for Africa CY - Berlin, Germany DA - 2011-08-17 PY - 2011 AN - OPUS4-24725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Hydration and strength development of calcite-rich wastepaper sludge ash N2 - In paper recycling large amounts of waste sludge, containing organics as well as inorganic fillers of the recycled paper, are produced. A large fraction of these sludges is incinerated; the ashes generated in this process, often referred to as wastepaper sludge ash (WSA), have the potential to be used as binder material, either alone or as supplementary cementitious material. However, ashes from different paper mills differ in their Chemical and mineralogical composition, thus, the reaction products and the properties of the hardened binders may vary s i gn i fi cantley. In the present study, a calcite-rich WSA was analyzed for reaction products and strength development. The WSA contained, besides calcite, hydraulic phases such as tricalcium aluminate (C3A) and belite (C2S), lime as well as inert phases. When activated with water, the WSA yielded a compressive strength of up to 12.3 MPa and the major hydration product was monocarboaluminate (C4A CO2 IIH2O or C4ACH11). Activation with 2M NaOH or 2M KOH solution caused a more rapid strength gain until one day of curing, but afterwards the strength development slowed down and the strength afiter 28 days was significantly lower than for the water-activated pastes. From TG analyses it is apparent that the higher strength of the alkaliactivated pastes after one day of curing was caused by a more rapid consumption of calcite and associated formation of C4ACH11. At later curing times the amount of calcite did not change substantially and consequently strength development almost ceased. The results demonstrate the complex influence of alkaline conditions on the hydration of WSA and show that the reaction products, which determine the durability properties of the hardened pastes (and materials made from it), of the calcite-rich WSA differ from the products of other WS As, as discussed in the article. T2 - CIC 2014 - Concrete Innovation Conference 2014 CY - Oslo, Norway DA - 11.06.2014 KW - Wastepaper sludge ash (WSA) KW - Alkali-activation KW - Strength KW - Tetracalcium monocarboaluminate PY - 2014 SP - 1 EP - 8 AN - OPUS4-31038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mundra, Shishir A1 - Samson, G. A1 - Masi, G. A1 - Achenbach, R. A1 - Bastidas, D. M. A1 - Bernal, S. A. A1 - Bignozzi, M. C. A1 - Criado, M. A1 - Cyr, M. A1 - Gartner, N. A1 - von Greve-Dierfeld, S. A1 - Legat, A. A1 - Nikoonasab, Ali A1 - Provis, J. L. A1 - Raupach, M. A1 - Gluth, Gregor T1 - Stahlkorrosion in alkalisch aktivierten Bindemitteln und Betonen: Anwendung elektrochemischer Methoden N2 - Alkalisch aktivierte Bindemittel (AAB) und Betone können herkömmliche Zemente beziehungsweise Betone potentiell in vielen Anwendungen ersetzen und dadurch den CO2-Fußabdruck der Bauindustrie wesentlich verkleinern. Zur Untersuchung der Stahlkorrosion in bewehrten („armierten“) Betonbauteilen werden elektrochemische Methoden wie Messungen des Freien Korrosionspotentials, des Polarisationswiderstands oder von Stromdichte-Potential-Kurven eingesetzt. Diese Methoden und die etablierten Grenzwerte zur Detektion von Korrosion sind für die Anwendung bei herkömmlichen Zementen beziehungsweise Betonen entwickelt und erprobt worden. Neue Forschungsergebnisse demonstrieren, dass Unterschiede zwischen den Porenlösungszusammensetzungen von herkömmlichen Zementen und bestimmten AAB sowie anderen schlackehaltigen Zementen erhebliche Unterschiede bei den Ergebnissen der elektrochemischen Messungen bewirken und damit zur fehlerhaften Detektion von Stahlkorrosion führen können. Ursache hierfür sind vor allem reduzierte Schwefelspezies in den Porenlösungen von AAB und anderen schlackehaltigen Zementen. KW - Zement KW - Hüttensandmehl KW - Schlacke KW - Sulfid KW - Korrosion PY - 2023 UR - https://bit.ly/GIT-Gluth UR - https://analyticalscience.wiley.com/content/magazine-do/git-labor-fachzeitschrift-10-2023 SN - 0016-3538 VL - 67 IS - 10 SP - 28 EP - 31 PB - Wiley-VCH AN - OPUS4-58573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Chloride binding by LDH/AFm phases and alkali-activated slag pastes N2 - Chloride binding by the hydrate phases of cementitious materials influences the rate of chloride ingress into these materials and, thus, the time at which chloride reaches the steel reinforcement in concrete structures. A particularly important role in this context is played by layered double hydroxides (LDHs), including AFm phases. Chloride binding isotherms of individual LDH/AFm phases would be required as input for computational models of chloride ingress, but such isotherms are only available for a few AFm phases, and in addition the available data are partly conflicting. The present study, conducted in the context of RILEM TC 283-CAM ‘Chloride transport in alkali-activated materials’, significantly extends the available database by determining the chloride binding isotherms of LDH/AFm phases (monosulfate, strätlingite, hydrotalcite, and meixnerite), and of alkali-activated slags (AAS) produced with four different activators (Na2SiO3, Na2O∙1.87SiO2, Na2CO3, and Na2SO4), in NaOH/NaCl solutions at various liquid/solid ratios. Selected solids after chloride binding were analysed by X-ray diffraction, and thermodynamic modelling was applied to simulate the phase changes occurring during chloride binding by the AFm phases. The chloride binding isotherms of LDH/AFm phases depended strongly on the liquid/solid ratio during the experiments, resolving apparent contradictions of the previously available data. The dependency on liquid/solid ratio must be attributed to kinetic restrictions, which are, however, currently poorly understood. Chloride binding by AAS pastes was generally higher than for Portland cement pastes and was only moderately influenced by the employed activator. A steep increase of the chloride binding by AAS occurred at free chloride concentrations above approx. 1.0 M, which is possibly related to chloride binding by the C-(N-)A-S-H gel in the AAS. T2 - RILEM Spring Convention 2024 & Conference on Advanced Construction Materials and Processes for a Carbon Neutral Society CY - Milan, Italy DA - 07.04.2024 KW - Chloride binding KW - Layered double hydroxides KW - AFm phases KW - Alkali-activated slags KW - Chloride sorption isotherms PY - 2024 AN - OPUS4-59855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Thermo-mechanical and spalling behavior of normal weight and lightweight geopolymer concretes N2 - The mechanical and microstructural properties of two geopolymer concretes, produced with either quartz aggregate or expanded clay aggregate, were assessed before, during and after high-temperature exposure up to 750 °C in order to better understand the engineering properties of the material. SEM investigations were also undertaken to better understand the observed changes in the mechanical properties. It was found that dehydration of capillary water caused micro-cracking and strength losses at temperatures ≤ 300 °C. At higher temperatures (T ≥ 500 °C) sintering promoted strength increases, leading significant strength advantages over conventional concretes. Stress-mechanical strain curves, which are the basis of the fire design of concrete structures, were determined. In addition, the two geopolymer concretes where exposed to the ISO 834-1 standard fire curve in a small-scale spalling test set-up. Acoustic emission measurements during, and acoustic measurements and optical microscopy after heat exposure were employed to investigate crack formation during the tests. Both concretes did not spall, which is attributed to their comparatively high permeability and their low amount of chemically bound water. Significant crack formation was detected only around the temperature of the α–β quartz transition (573 °C) and on cooling. Because of aggregate deformations at the quartz transition temperature, deterioration after heating was more significant in the geopolymer concrete with quartz aggregates. Crack formation occurred also in the concrete with expanded clay aggregates, presumably caused by shrinkage of the geopolymer paste on cooling. T2 - Advances in Cement and Concrete Technology in Africa (ACCTA 2016) CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Geopolymers KW - Concrete KW - Transient thermal creep KW - Spalling KW - Heat exposure PY - 2016 AN - OPUS4-36922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Alkalisch aktivierte Bindemittel mit hohem Säurewiderstand für die Kanalsanierung N2 - Die biogene Schwefelsäurekorrosion (BSK) von Betonbauteilen in Abwassersystemen verursacht weltweit hohen Reparaturbedarf. Um zukünftigen Reparaturbedarf zu minimieren, werden für Neubau- und Sanierungsmaßnahmen z. T. Materialien mit besonders hohem Widerstand gegen BSK benötigt. Der vorliegende Beitrag beschreibt Forschungen zu alkalisch aktivierten Bindemitteln, die bei geeigneter Formulierung einen hohen Widerstand gegen BSK bzw. Säureangriff aufweisen. Zusätzlich werden jüngste Fortschritte bei der Bewertung von Methoden zur Prüfung des Widerstands gegen BSK dargestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Alkalisch aktivierte Bindemittel KW - Biogene Schwefelsäurekorrosion KW - Säurewiderstand PY - 2024 AN - OPUS4-61747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Geopolymers - Novel low-calcium cements T2 - International Conference on Advances in Cement and Concrete Technology in Africa - Pre Conference Workshop CY - Johannesburg, South Africa DA - 2013-01-25 PY - 2013 AN - OPUS4-27662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Rickard, W. ED - Leonelli, C. ED - Romagnoli, M. T1 - Design and characterization of fly ash-based geopolymer concretes for a round-robin durability testing program N2 - Fly ash-based, ambient-cured geopolymer concretes for a round-robin durability testing program were designed and characterized. Optimum activator composition was determined based on the Chemical composition of the amorphous part of the fly ash. Fly ash content, water content, and grading curves of the aggregates were varied for the concretes. Characterization of the concretes involved flow diameter, air void content, density, compressive strength, and permeability. The workability of the concretes was notably sensitive to changes in the mix-design. The majority of strength development in the concretes occurred within the first 28 days of curing; concrete strengths reached up to 86 MPa after 56 days. Two concretes, both with sufficient workability, but significantly different grading curve, water content, strength and permeability were identified to be suitable for the round-robin testing program. T2 - Geopolymers 2015 - The route to eliminate waste and emissions in ceramic and cement manufacturing - Engineering conference international (ECI) CY - Hernstein, Austria DA - 24.05.2015 KW - Fly ash geopolymer concrete KW - Concrete properties KW - Permeability PY - 2015 SN - 978-1-326-37732-8 SP - 67 EP - 70 AN - OPUS4-33106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Reaction products and strength development of wastepaper sludge ash and the influence of alkalis N2 - Wastepaper sludge ash (WSA) from a newsprint paper mill was investigated for its mineralogical composition and its reaction products and strength development after activation with water and sodium and potassium hydroxide solutions. The results showed the WSA to consist of calcite, free lime, gehlenite, tricalcium aluminate, belite, talc, quartz and probably a glassy phase. The principle reaction product was monocarboaluminate (CO3–AFm) for the water- as well as for the alkali-activated WSA. Formation of monocarboaluminate and strength gain was more rapid for the alkali-activated WSA until 1 day of curing. However, afterwards reactions proceeded much slower when alkali solutions were used, leading to an about twice as high compressive strength for water-activated WSA mortars after 28 days of curing. The observed behavior is tentatively ascribed to a less uniform microstructure of the alkali-activated WSA. Significant differences between NaOH- and the KOH-activated WSA were not observed. KW - Wastepaper sludge ash KW - Reaction products KW - Monocarboaluminate KW - Strength KW - Alkali-activation PY - 2014 DO - https://doi.org/10.1016/j.cemconcomp.2013.09.009 SN - 0958-9465 SN - 1873-393X VL - 45 SP - 82 EP - 88 PB - Elsevier CY - Barking, Essex AN - OPUS4-29930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Reinforcing steel in sulfide-containing concretes – corroding or not corroding? N2 - Blast furnace cements (CEM III) and alkali-activated slags are binders for concretes with several advantageous engineering properties, and their increased adoption in construction industry could contribute to reducing the CO2 emissions associated with cement production and use. However, the current knowledge about how these cements protect steel reinforcement in concretes against corrosion is very incomplete, which impedes their large-scale application. This knowledge gap is mainly due to the fact that these cements release sulfide and other reduced sulfur species into the concrete pore solution, the consequences of which for the state of the reinforcement and electrochemical measurements are not fully understood. The present contribution first describes peculiarities of electrochemical measurements of steel in sulfide-containing cementitious materials and related solutions as reported in the literature and a recent report by EFC Working Party 11. It is demonstrated that the high sulfide concentrations in these systems lead to low open circuit potentials and low polarisation resistances, which may be incorrectly interpreted as indicating active corrosion of the steel. Second, preliminary results of an ongoing project [funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) – 458297195] related to the passivation and corrosion initiation of steel in sulfide-containing solutions and mortars are presented. Eight mortars based on one alkali-activated blast furnace slag (BFS), three alkali-activated BFS/fly ash blends, one sodium sulfate-activated CEM III/C (‘hybrid cement’), one CEM III/C, one CEM III/B, and one CEM I (ordinary Portland cement, OPC) were produced, and their pore solutions expressed and analysed after 7, 14, 28, and 56 days of curing. The pH values of the solutions differed systematically, with the highest pH values recorded for the CEM I and the alkali-activated BFS/fly ash blends with a high proportion of fly ash, and the lowest pH recorded for the CEM III/B. The redox potentials of the solutions were between −500 mV and −340 mV vs. Ag/AgCl for the alkali-activated binders, approx. +10 mV vs. Ag/AgCl for the CEM I, and in between for the CEM III/B and the CEM III/C. As expected, the electrical conductivity was highest for the alkali-activated binders. These results are explained by the chemical compositions of the pore solutions of the mortars. Finally, a test set-up to investigate the behaviour of steel in sulfide-containing solutions and the changes on subsequent oxygen and/or chloride addition is introduced. Preliminary electrochemical measurements of steel in sulfide-containing solutions are presented and discussed in the context of the above-mentioned data from the literature and the compositions of the pore solutions of the studied mortars. T2 - 7th Swiss Corrosion Science Day 2023 CY - Zurich, Switzerland DA - 24.04.2023 KW - Reinforcing steel KW - Sulfide KW - Concrete KW - Ground granulated blast furnace slag KW - Corrosion PY - 2023 AN - OPUS4-57386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - One-part geopolymers and geopolymer-zeolite composites based on silica: factors influencing microstructure and engineering properties N2 - Mixing and curing of geopolymers and related alkali-activated materials without storage and handling of highly alkaline solutions possesses advantages regarding safety and economic viability; one possible approach is to produce these materials from solid silica feedstocks and solid sodium aluminate, and subsequent mixing with water. We present a comparison between geopolymers and geopolymer-zeolite composites synthesized by this route from different silica feedstocks (by-product silica from chlorosilane production, microsilica, rice husk ash) and with different SiO2/Al2O3 ratios, using results from XRD, NMR, SEM, thermal analysis, mechanical and acid resistance testing. The use of rice husk ash favors formation of a fully amorphous geopolymer with high strength. Utilization of the other silica feedstocks leads to formation of geopolymer-zeolite composites, the amount and kind of zeolites depending on the feedstock and the SiO2/Al2O3 ratio. These composites show beneficial dehydration behavior, viz. no distinct dehydration step of thermal strain, with the phase assemblage after heating to 1000 °C controlled by the starting composition. Mortars produced from both, the geopolymers as well as the compo¬sites, exhibit high resistance to sulfuric acid attack, making them promising materials for the construction and the repair of industrial and sewer structures. T2 - 42nd International Conference and Expo on Advanced Ceramics and Composites CY - Daytona Beach, FL, USA DA - 21.01.2018 KW - Alkali-activated materials KW - Geopolymers KW - Acid resistance KW - High-temperature resistance PY - 2018 AN - OPUS4-44145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Geopolymerisation kieselsäurehaltiger Rückstände aus der Reststoffaufbereitung der Chlorosilanproduktion T2 - 18. Internationale Baustofftagung (IBAUSIL) CY - Weimar, Germany DA - 2012-09-12 PY - 2012 AN - OPUS4-26556 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Structure, acid resistance and high-temperature behavior of silica-based one-part AAMs N2 - One-part geopolymers (OPGs) are a sort of alkali-activated materials (AAMs) which production avoids the use of highly-alkaline activator-solutions and contributes to a better acceptance of alternative mineral binders in terms of safety-related and economic aspects. In the present contribution OPGs were synthesized by blending silica sources (two industrial silicas and two biogenic silicas) with sodium aluminate and only water must be added to initiate the hardening, i.e. mixing is performed in the same way as for conventional Portland cements. The OPGs were characterized by XRD, and SEM and the degrees of reaction of the silicas were determined by a chemical dissolution method. The industrial silicas led to the formation of geopolymer-zeolite composites, that contained, besides geopolymeric gel, crystalline tectosilicates (e.g. zeolite A and hydrosodalite) and depending on the starting composition also unreacted silica. The biogenic silicas provided a higher reactivity and avoided the formation of crystallite by-products. The differences in the microstructures caused differences in the mechanical strength of the specimens. The treatment of the OPG composites at moderate elevated temperatures revealed promising behavior on thermal dehydration in terms of shrinkage and residual strength up to 700 °C. Above 700 °C sintering and partial melting occurred, and new phase formation commenced. After exposure to 1000 °C the specimens appeared virtually amorphous or formed stuffed silica structures of nepheline- or carnegieite-type type. The investigations of the OPG based mortars on their resistance against sulfuric acid in accordance with DIN 19573 (Appendix A) revealed very high residual strengths up to 78 % after treatment with H2SO4 (pH 1) for 70d. A mechanism of dissolution of the primary aluminosilicate reaction products of the pastes and the precipitation of a silica gel that protects the remaining aluminosilicates and decelerates further corrosion was found to be the main reason for the good performance under acidic conditions. The addition of CaO-containing feedstocks enhanced hardening, but at a certain content the resistance against sulfuric acid decreased, due to the formation of gypsum on exposure to sulfate. In addition, the mortars exhibited excellent shrinkage behavior as well as good bond to concrete substrates with pull-off strength up to > 3 MPa. The workability of the fresh mortars provided very good manual applicability; automatic applications such as sprayed and spun mortars will require further optimization regarding rheological properties. In summary, the studied OPG are promising materials for the construction and the repair of concrete structures, such as sewers, that are affected by biogenic sulfuric acid corrosion. T2 - Alkali Activated Materials and Geopolymers CY - Tomar, Portugal DA - 27.05.2018 KW - Alkali-activated materials KW - Geopolymers KW - Acid resistance KW - Solid state NMR PY - 2018 AN - OPUS4-45087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhang, W. A1 - Gaggl, M. A1 - Gluth, Gregor A1 - Behrendt, F. T1 - Gas separation using porous cement membrane N2 - Gas separation is a key issue in various industrial fields. Hydrogen has the potential for application in clean fuel technologies. Therefore, the separation and purification of hydrogen is an important research subject. CO2 capture and storage have important roles in 'green chemistry'. As an effective clean technology, gas separation using inorganic membranes has attracted much attention in the last several decades. Membrane processes have many applications in the field of gas separation. Cement is one type of inorganic material, with the advantages of a lower cost and a longer lifespan. An experimental setup has been created and improved to measure twenty different cement membranes. The purpose of this work was to investigate the influence of gas molecule properties on the material transport and to explore the influence of operating conditions and membrane composition on separation efficiency. The influences of the above parameters are determined, the best conditions and membrane type are found, it is shown that cementitious material has the ability to separate gas mixtures, and the gas transport mechanism is studied. KW - Gas separation KW - Porous membrane KW - Clean fuel KW - Cement membrane KW - Inorganic membranes PY - 2014 DO - https://doi.org/10.1016/S1001-0742(13)60389-7 SN - 1001-0742 SN - 1878-7320 VL - 26 IS - 1 SP - 140 EP - 146 CY - Beijing, China AN - OPUS4-30039 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Design and Characterization of Fly Ash-Based Geopolymer Concretes for a Round Robin Durability Testing Program T2 - Geopolymers: The route to eliminate waste and emissions in ceramic and cement manufacturing CY - Hernstein, Austria DA - 2015-05-24 PY - 2015 AN - OPUS4-33513 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten ED - Bílek, V. ED - Kersner, Z. T1 - Influence of sodium concentration of the activating solution on the hydration of calcium carbonate-rich wastepaper sludge ash N2 - In paper recycling several types of waste sludges are produced, which contain organics as well as inorganic fillers of the recycled paper, e.g. kaolinite, calcite, talc, or titanium dioxide [1,2]. Part of these sludges is incinerated to recover energy and to reduce the volume of waste to be handled. The ashes generated in this process are commonly referred to as wastepaper sludge ash (WSA). The quantities of WSA produced are large and at present much of it is still landfilled or otherwise handled entailing costs. Depending on the composition of the recycled paper and the conditions during processing and incineration, WSA can have cementitious properties. In the present investigation a CaC03-rich WSA was analyzed for reaction products and strength development after hydration with water, 2 M NaOH solution and 8 M NaOH solution. The rationale for activating the WSA with NaOH was to assess the behaviour of the WSA when alkalis are introduced to the System or when the WSA is used as addition in alkali-activated binders. T2 - NTCC2014 - International conference on non-traditional cement and concrete CY - Brno, Czech Republic DA - 16.06.2014 KW - Wastepaper sludge ash KW - Calcium carbonate KW - Alkali-activation KW - Monocarboaluminate KW - AFm KW - Hydrogarnet PY - 2014 SN - 978-80-214-4867-4 SP - 71 EP - 74 PB - Novpress AN - OPUS4-30992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Zhang, W. A1 - Gaggl, M. A1 - Hillemeier, B. A1 - Behrendt, F. T1 - Multicomponent gas diffusion in hardened cement paste at temperatures up to 350 °C N2 - Diffusional gas transport of a H2/CO2 mixture versus N2 in the pore system of hardened cement pastes was studied at four temperatures up to 350 °C in a Wicke-Kallenbach cell. The pastes possessed separation factors αH2,CO2 from 1.42 to 3.43, i.e. the diffusion of hydrogen took place considerably faster than the diffusion of carbon dioxide. The separation factors depended on the threshold radii of the pastes, smaller threshold radii leading to higher separation factors. The Knudsen numbers of the controlling constrictions of the pore system and the temperature dependence of the effective diffusion coefficients of the gases show that gas transport in these constrictions takes place in the transient regime between Knudsen diffusion and bulk diffusion, smaller constriction widths leading to predominating Knudsen diffusion. It is therefore possible to use cement paste membranes to separate gas components of low molecular weight from higher weight components. KW - Microstructure (B) KW - Mercury porosimetry (B) KW - Diffusion (C) KW - Cement paste (D) KW - Gas separation KW - Pore structure PY - 2012 DO - https://doi.org/10.1016/j.cemconres.2012.02.001 SN - 0008-8846 SN - 1873-3948 VL - 42 IS - 5 SP - 656 EP - 664 PB - Pergamon Press CY - New York, NY AN - OPUS4-25655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Rickard, W.D.A. A1 - Werner, Steve A1 - Pirskawetz, Stephan T1 - Acoustic emission and microstructural changes in fly ash geopolymer concretes exposed to simulated fire N2 - Two fly ash-based geopolymer concretes with quartz aggregates or with expanded clay (lightweight) aggregates were exposed to the ISO 834-1 standard fire curve in a small-scale fire test set-up. Acoustic emission measurements during fire exposure and subsequent cooling were employed to study spalling events and cracking during the tests. Optical microscopy and additional acoustic measurements were conducted after the testing to better understand the crack propagation in the samples. The testing revealed that neither of the concretes were susceptible to spalling, which is particularly notable for the concrete with quartz aggregates, as it is a high-strength concrete. This behavior is attributed to the relatively high permeability of the concretes and their low amount of chemically bound water. Significant crack formation was detected only around the temperature of the alpha–beta quartz transition (573 °C) and on cooling. Because of aggregate deformations at the quartz transition temperature, deterioration after heating was more significant in the geopolymer concrete with quartz aggregates. Crack formation also occurred in the concrete with expanded clay aggregates, caused by shrinkage of the geopolymer paste on cooling. Acoustic emission measurements proved to be a valuable tool to investigate processes during high temperature exposure. KW - Geopolymers KW - Spalling KW - Concrete KW - Acoustic emission KW - Heat exposure PY - 2016 DO - https://doi.org/10.1617/s11527-016-0857-x SN - 1359-5997 SN - 1871-6873 VL - 49 IS - 12 SP - 5243 EP - 5254 PB - Springer AN - OPUS4-36907 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Gluth, Gregor A1 - Watolla, Marie-Bernadette A1 - Morys, Michael A1 - Häßler, Dustin A1 - Schartel, Bernhard T1 - Neue Wege: Reaktive Brandschutzbeschichtungen für Extrembedingungen N2 - Wesentlich für das Sicherheitsniveau und damit die nachhaltige Wettbewerbsfähigkeit des Technologiestandortes Deutschland ist der Brandschutz in Industrieanlagen, in Gebäuden und im Transportwesen. Der vorbeugende bauliche Brandschutz hat u. a. das Ziel, die Brand- und Rauchausbreitung im Brandfall für eine gewisse Zeit zu behindern, damit die erforderlichen Lösch- und Rettungsarbeiten durchgeführt werden können. Dies geschieht u.a. durch Anforderungen an die Feuerwiderstandsfähigkeit brandbeanspruchter Bauteile. Der Feuerwiderstand eines Bauteils ist die Fähigkeit während eines angegebenen Zeitraums in einer genormten Feuerwiderstandsprüfung bezüglich mechanischer Stabilität und/oder thermischer Isolierung nicht zu versagen. Reaktive Brandschutzbeschichtungen erhöhen für viele Bauteile sehr effektiv den Feuerwiderstand. Die Beschichtungen und die Brandprüfungen müssen jedoch an die immer komplexeren Anwendungen und/oder extremeren Anforderungen angepasst und weiterentwickelt werden. Aktuelle Forschungsschwerpunkte liegen dabei in der Entwicklung neuer Materialien (z.B. Geopolymere, keramisierende Beschichtungen, silikonbasierte Beschichtungen) für extreme Brandszenarien (extreme Temperaturen, lange Beanspruchungszeiten) und in der Realisierung komplexer Funktionalitäten (komplexe Geometrien, bewegliche Komponenten) sowie in der Entwicklung neuer Testmethoden (Feuerwiderstand als bench-scale Tests, kostengünstiges Screening, Feuerwiderstand in extremen Brandszenarien). Die Entwicklung geht dabei weg von der präskriptiven Bewertung hin zur leistungsorientierten (performance-based) Bewertung in individuellen Brandszenarien oder von komplexen Bauteilen. Im Rahmen dieser Arbeit werden Lösungsansätze für die neuen Herausforderungen an die reaktiven Brandschutzsysteme unter Extrembedingungen und deren Testmöglichkeiten vorgestellt und diskutiert. Im Mittelpunkt stehen dabei neu entwickelte bench-scale Testmethoden zum Screening von neuen Beschichtungsmaterialien sowie zur Beurteilung spezieller bzw. materialspezifischer Aspekte des Feuerwiderstands unter Extrembedingungen. KW - Reaktive Brandschutzsysteme KW - Brandtest PY - 2016 DO - https://doi.org/10.1002/bate.201600032 SN - 0932-8351 SN - 1437-0999 VL - 93 IS - 8 SP - 531 EP - 542 PB - Ernst & Sohn CY - Berlin AN - OPUS4-37115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pistol, Klaus A1 - Gluth, Gregor A1 - Rickard, W. T1 - Mechanische Hochtemperatureigenschaften von flugaschebasierten Geopolymerbetonen N2 - Als umweltschonende Alternative zu portlandzementgebundenen Betonen werden derzeit in der Betonindustrie und in der Baustoffforschung Betone mit alkaliaktivierten Bindemitteln, sog. Geopolymerbetone, intensiv erforscht. Die auf industriellen Reststoffen wie Flugasche und Hüttensand basierenden anorganischen Bindemittel weisen bei geeigneter Zusammensetzung einen hohen Widerstand gegenüber aggressiven Salzlösungen und Säuren auf. Als Grundlage für den rechnerischen Nachweis der Tragfähigkeit von brandbeanspruchten Betonbauteilen auf Basis von alkaliaktivierten Bindemitteln werden deshalb an der Bundesanstalt für Materialforschung und -prüfung (BAM) die mechanischen Hochtemperatureigenschaften von flugaschebasierten Geopolymerbetonen systematisch untersucht. Die bis zu 750 °C erhitzten Probekörper mit quarzitischer und leichter Gesteinskörnung zeigen einen Festigkeitsverlust bis ca. 300 °C, der auf entwässerungsbedingte Mikrorissbildung zurückgeführt werden kann. Bei weiter zunehmender Temperatur steigt aufgrund von Sinterungsprozessen ab ca. 500 °C die Festigkeit der untersuchten Geopolymerbetone wieder an. Diese im Vergleich zu herkömmlichem Beton günstigere Materialeigenschaft eröffnet potenziell auch Anwendungsmöglichkeiten in brandschutztechnisch kritischen Infrastrukturbereichen. Die Ergebnisse der thermomechanischen Prüfungen werden für numerische Bauteilberechnungen als temperaturabhängige Spannungs-Dehnungs-Beziehungen aufbereitet. N2 - At present, concretes based on alkali-activated binders, socalled geopolymer concretes, are investigated intensively in the building materials industry and by the research community as environmentally friendly alternative to Portland cementbased concretes. These inorganic binders, which are based on industrial by-products such as fly ash and ground granulated blast furnace slag, exhibit high resistance against corrosive acids and salts, if properly designed. The mechanical properties of fly ash-based geopolymer concretes at high temperatures are subject of systematic investigations at the Bundesanstalt für Materialforschung und -prüfung (BAM) to create a basis for the structural design of fire exposed concrete members based on alkali-activated binders. The concrete specimens, produced with quartz aggregates or lightweight aggregates and heated to a maximum temperature of 750 °C, exhibited a decrease of compressive strength up to temperatures of ca. 300 °C, attributed to formation of microcracks caused by dehydration. At higher temperatures the compressive strength of the investigated geopolymer concretes recovered partly, due to sintering processes starting from ca. 500 °C. Because of this beneficial property when compared to conventional concretes, geopolymer concretes can potentially be applied in infrastructure facilities where fire resistance is critical. From the results of the thermomechanical tests stress-strain relationships are derived that can be used for the structural design of members made from geopolymer concretes. KW - Geopolymerbeton KW - Hochtemperatureigenschaften KW - Feuerwiderstand KW - Spannung-Dehnungs-Beziehung PY - 2016 DO - https://doi.org/10.1002 / bate.201600038 SN - 0932-8351 SN - 1437-0999 VL - 93 IS - 8 SP - 521 EP - 530 PB - Ernst & Sohn CY - Berlin AN - OPUS4-37114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Inhalt der Verordnungen für Heizungsanlagen - Überblick N2 - Seit dem 26.09.2015 gelten in Deutschland Anforderungen an die umweltgerechte Gestaltung und die Energiekennzeichnung von Heizgeräten und Verbundanlagen mit Heizgeräten. Der Vortrag stellt die zugrundeliegenden EU-Verordnungen und die sich ergebenden Konsequenzen überblicksmäßig vor. T2 - Kolloquium Marktüberwachung im Bereich Heizungsanlagen CY - Berlin, Germany DA - 06.04.2016 KW - Heizgeräte KW - Verbundanlagen KW - Umweltgerechte Gestaltung KW - Ökodesign KW - Energieverbrauchskennzeichnung PY - 2016 AN - OPUS4-36924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Influence of sodium concentrations of the activating solution on the hydration of calcium carbonate-rich wastepaper sludge ash T2 - 5th International Conference on Non-Traditional Cement & Concrete CY - Brno, Czech Republic DA - 2014-06-16 PY - 2014 AN - OPUS4-33514 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Structural Investigations n One-Part Geopolymers after Different Drying Regimes T2 - 34th Cement & Concrete Science Conference CY - Sheffield, England DA - 2014-09-14 PY - 2014 AN - OPUS4-33516 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -