TY - CONF A1 - Geißler, Peter A1 - Schwarz, Johannes A1 - Cuéllar, Pablo A1 - Hüsken, Götz A1 - Baeßler, Matthias A1 - Kühne, Hans-Carsten A1 - Morrone, C. T1 - Compaction grouting to improve the pile bearing capacity in non-cohesive soil N2 - The aim of an ongoing research project is to develop a design approach for typical offshore driven piles (e.g. Jacket piles) based on the application of injections by compaction grouting directly at the pile shaft. The paper aims to present the results of laboratory and in-situ tests, which reveal the efficiency and the promising potential of the optimised foundation concept for a more economic dimensioning of pile foundations and to increase their bearing capacity in non-cohesive soil at any moment after installation. T2 - Twenty-ninth International Ocean and Polar Engineering Conference CY - Honolulu, HI, USA DA - 16.06.2019 KW - Offshore Pile Foundation KW - Compaction Grouting KW - Grout KW - Injection Sequence KW - Tensile Capacity PY - 2019 SN - 978-1-880653-85-2 SN - 1098-6189 VL - II SP - 2178 EP - 2184 PB - International Society of Offshore and Polar Engineers (ISOPE) CY - Cupertino, California, USA AN - OPUS4-48505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz A1 - Shamsuddoha, Md A1 - Thiele, Marc A1 - Baeßler, Matthias A1 - Kühne, Hans-Carsten T1 - Comparison of cracks formed in scaled grouted connection of offshore energy structures under static and cyclic loads N2 - Global energy consumption will increase in the future necessitating both fossil fuels and renewable energy choices - especially wind energy. Such high energy demand requires installation of offshore energy structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with maintenances. Due to their large size and remote locations, cylindrical grouted joints are often adopted between substructure and foundation in these offshore platforms and wind structures such as monopiles. However, these connections are composite structures with exterior sleeve, interior pile and infill mortar. Degradation and settlements were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites were proven difficult to obtain ideal load bearing capacity. In-situ loading conditions were also found to be affecting the failure mechanism inside such connections. This study aims at characterizing the nature of cracks generated in these grouted connections under both static and cyclic loading. Scaled grouted joints were manufactured using a novel reusable mold, and connections were loaded to failure to visualize the main failure patterns. An assessment between failure under these two types of load is drawn along with comparison to previously available literature. T2 - 5th International Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures CY - Potsdam, Germany DA - 27.08.2019 KW - Grouted connection KW - Crack formation KW - Crack pattern KW - Static load KW - Cyclic load PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-487961 SP - Th.2.A.1-1 EP - Th.2.A.1-9 AN - OPUS4-48796 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz T1 - Comparison of cracks formed in scaled grouted connection of offshore energy structures under static and cyclic loads N2 - Global energy consumption will increase in the future necessitating both fossil fuels and renewable energy choices - especially wind energy. Such high energy demand requires installation of offshore energy structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with maintenances. Due to their large size and remote locations, cylindrical grouted joints are often adopted between substructure and foundation in these offshore platforms and wind structures such as monopiles. However, these connections are composite structures with exterior sleeve, interior pile and infill mortar. Degradation and settlements were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites were proven difficult to obtain ideal load bearing capacity. In-situ loading conditions were also found to be affecting the failure mechanism inside such connections. This study aims at characterizing the nature of cracks generated in these grouted connections under both static and cyclic loading. Scaled grouted joints were manufactured using a novel reusable mold, and connections were loaded to failure to visualize the main failure patterns. An assessment between failure under these two types of load is drawn along with comparison to previously available literature. T2 - 5th International Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures CY - Potsdam, Germany DA - 27.08.2019 KW - Grouted connection KW - Crack formation KW - Crack pattern KW - Static load KW - Cyclic load PY - 2019 AN - OPUS4-48797 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz T1 - Application of Steel Fibres in Alkali-Activated Mortars N2 - Alkali-activated materials are ideal for the repair of concrete structures in harsh environmental conditions due to their high durability in chemically aggressive environments. However, slag-based mortars, in particular, are prone to shrinkage and associated cracks. In this respect, the application of steel fibres is one solution to reduce the formation of shrinkage induced cracks and to improve post cracking behaviour of these mortars. This study investigated the influence of two different types of steel fibres on the tensile properties of two alkali-activated mortars. Direct tensile tests and single fibre pull-outs were performed to analyse the determining failure modes both on macro and micro scale. Mechanical testing was accompanied by non-destructive testing methods such as digital image correlation and acoustic emission for a detailed analysis of the fracture process. T2 - 14th International Conference on Local Mechanical Properties CY - Prague, Czech Republic DA - 06.11.2019 KW - Steel fibres KW - Alkali-activated materials KW - Tensile strength KW - Fibre pull-out PY - 2019 AN - OPUS4-49578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Hüsken, Götz A1 - Gründer, Klaus-Peter A1 - Kadoke, Daniel ED - Caspeele, R. ED - Taerwe, L. ED - Frangopol, D. M. T1 - Damage mechanisms analysis of reinforced concrete beams in bending using non-destructive testing N2 - Beams that are loaded in transverse direction are one of the main structural elements used in reinforced concrete structures. Bending beams are used, for example, in bridge girders or joists. The strength related failure modes at maximum loading can be divided into bending and shear failure that could occur with or without indication. Conventional design concepts used in practice for designing structural elements subjected to bending aim at failure modes with sufficient indication (e.g. large deflections or cracks), as it occurs in the case of secondary flexure-compression-failure. These indicators can also be used to identify structural changes of civil infrastructure systems (e.g. bridges) using non-destructive testing methods for Structural Health Monitoring (SHM). However, profound knowledge on the determining failure modes of bending beams is required for the reliable application of structural health monitoring. Therefore, resulting effects of different thermal and mechanical loads on the response of a structure are investigated by means of a bridge demonstrator. The results of this investigation are used for developing a monitoring system. Different non-destructive testing (NDT) methods have been used for analyzing the deformation behavior of a reinforced concrete beam in bending. The suitability of the different measuring techniques will be discussed by means of the obtained experimental results. For this purpose, the deformation behavior of a reinforced concrete beam having a span of 2.75 m was investigated in a four-point bending flexural test at laboratory scale. The focus is on the characterization of determining failure modes by the NDT methods and the comparison with classical measuring techniques (e.g. deformation measurements by displacement transducers). The bending tests have been accompanied by Acoustic Emission analysis (AE), optical deformation measurements using Stereophotogrammetry (SP) and Digital Image Correlation (DIC). The conducted tests have shown that the three-dimensional detection of deformations and resulting strains with optical techniques is beneficial for analyzing the damage mechanism of loaded structures and related crack formation and propagation. Optical techniques can be supplemented by acoustic emission testing which gives detailed information on crack formation and progressing damage. The combination of both techniques offers the application as efficient monitoring system for larger structures. T2 - Sixth International Symposium on Life-Cycle Civil Engineering (IALCCE 2018) CY - Ghent, Belgium DA - 28.10.2018 KW - Concrete Beam KW - Bending KW - Digital Image Correlation KW - Stereophotogrammetry KW - Acoustic Emission Analysis KW - Non-Destructive Testing PY - 2019 SN - 978-1-138-62633-1 SN - 978-1-315-22891-4 SP - 2411 EP - 2417 PB - CRC Press AN - OPUS4-46439 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schönsee, Eric A1 - Hüsken, Götz A1 - Kocherla, Amarteja A1 - Strangfeld, Christoph T1 - Influences of Surface Properties on the Reflection Intensity - Towards in Situ Monitoring During Early Age Hydration of CEM I N2 - Interlayer bonding in 3D concrete printing is influenced by the hydration progress and surface moisture of the previously printed layer. For effective quality control, continuous in situ monitoring of interlayer surface properties is required. This study investigated reflection intensity as a method for in situ measurements during the hydration of CEM I mixtures with varying retarder contents. Additional factors influencing the reflection intensity are also examined. Two laser line scanners with different wavelengths were used to track hydration over 72 h. Vicat tests and isothermal calorimetry served as reference methods. Across all the mixtures, the reflection intensity exhibited a repeatable pattern with five different stages. A sharp increase in intensity during the third stage was consistent with the acceleration period of hydration. These findings suggest that reflection intensity measurements could serve as a promising tool for evaluating interlayer bonding in 3D concrete printing. KW - In situ hydration monitoring KW - Cement KW - Optical methods KW - Reflection intensity KW - Additive manufacturing KW - Isothermal calorimetry PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-653430 DO - https://doi.org/10.1007/s10921-025-01326-2 SN - 1573-4862 VL - 45 IS - 1 SP - 1 EP - 17 PB - Springer Nature AN - OPUS4-65343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Agasty, Amit A1 - Costard, Rene A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - A comprehensive experimental assessment of reinforced concrete walls under blast: In situ monitoring of loading, dynamic response and damage with NDT methods and embedded sensors N2 - A safety or security related assessment of explosions, accidental and intentional scenarios alike, often necessitate performance of resource intensive replication tests. For an efficient assessment without performing full scale blast tests, e.g., supported by numerical simulations, detailed knowledge is necessary to predict the blast loading from a given charge configuration, the resulting dynamic response of the structure under investigation as well as the resulting damage. Validation of numerical simulation requires the spatially resolved acquisition of all these parameters in real time. In this paper we present a set of measurement techniques and discuss their suitability for monitoring reinforced concrete (RC) walls under blast loading. Different blast-loading scenarios were realized by varying the charge weight and the standoff distance. The dynamic loading of the wall was characterized with pressure sensors complemented by numerical simulations using the APOLLO Blastsimulator and ConWep. High speed digital image correlation (DIC) was implemented in combination with multiple acceleration sensors to observe the dynamic deflection of the walls during the loading and to determine the residual deformation after the loading had ceased. In addition, one test specimen was instrumented with fiber optic sensor cables. These fiber optic sensors were used for distributed acoustic sensing (DAS) delivering information on dynamics of compression and tension cycles from within the structure. Additionally, the local damage pattern emerging during the series of blasts was determined via distributed fiber optic strain sensing (DSS) to enable the characterization of visual and non-visual damage to the structure. The obtained information was compared to results by an ultrasound structure-scanner. KW - Blast testing KW - Reinforced concrete KW - NDT methods KW - Fiber optic sensing KW - DIC KW - Numerical simulations KW - APOLLO Blastsimulator PY - 2025 DO - https://doi.org/10.1177/20414196251353795 SN - 2041-4196 SP - 1 EP - 31 PB - Sage Publications AN - OPUS4-63832 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Nanjie Hu A1 - Hüsken, Götz T1 - Influence of activator composition on the strength, shrinkage and chloride migration resistance of alkali-activated slag mortars N2 - Alkali-activated slag materials are known for their high Chloride penetration resistance. This makes them potentially applicable as repair systems for damaged steel-reinforced concrete structures, which are exposed to chloride attack. For this purpose, the influence of the activator composition, i.e. the SiO2 and Na2O concentration of the alkaline solution on a) the compressive strength, b) shrinkage and mass change and c) the resistance against chloride penetration of four alkali-activated slag mortars (AASM) were studied. An ordinary Portland cement-based mortar was used as the reference sample. Increasing SiO2 and Na2O concentrations increased the strength, shrinkage and mass loss of the AASMs. The resistance of the mortars against chloride penetration was evaluated using the non-steady-state migration coefficient Dnssm obtained from NT BUILD 492. The results indicate that the Dnssm is related to differences in the pore solution of the AASMs rather than to differences in their microstructure. An upcoming study of the authors is going to evaluate this hypothesis by the accelerated chloride penetration (diffusion) test. T2 - The 6th International Conference on Non-Traditional Cement and Concrete CY - Brno, Czech Republic DA - 20.06.2017 KW - Alkali-activated slag mortar KW - Strength KW - Shrinkage KW - Chloride migration coefficient PY - 2017 AN - OPUS4-44080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, Nanjie A1 - Hüsken, Götz A1 - Gluth, Gregor A1 - Kühne, Hans-Carsten T1 - The influence of activator composition on the strength, shrinkage and chloride migration resistance of alkali-activated slag mortars N2 - Alkali-activated slag materials are known for their high Chloride penetration resistance. This makes them potentially applicable as repair systems for damaged steel-reinforced concrete structures, which are exposed to chloride attack. For this purpose, the influence of the activator composition, i.e. the SiO2 and Na2O concentration of the alkaline solution on a) the compressive strength, b) shrinkage and mass change and c) the resistance against chloride penetration of four alkali-activated slag mortars (AASM) were studied. An ordinary Portland cement-based mortar was used as the reference sample. Increasing SiO2 and Na2O concentrations increased the strength, shrinkage and mass loss of the AASMs. The resistance of the mortars against chloride penetration was evaluated using the non-steady-state migration coefficient Dnssm obtained from NT BUILD 492. The results indicate that the Dnssm is related to differences in the pore solution of the AASMs rather than to differences in their microstructure. An upcoming study of the authors is going to evaluate this hypothesis by the accelerated chloride penetration (diffusion) test. T2 - 6th International Conference Non-Traditional Cement and Concrete 2017 CY - Brno, Czech Republic DA - 19.06.2017 KW - Alkali-activated slag mortar KW - Strength KW - Shrinkage KW - Chloride migration coefficient PY - 2018 DO - https://doi.org/10.4028/www.scientific.net/KEM.761.61 SN - 1662-9795 VL - 761 SP - 61 EP - 64 PB - Trans Tech Publications CY - Switzerland AN - OPUS4-43884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Schönsee, Eric A1 - Jeyifous, Olubunmi Anthony A1 - Mezhov, Alexander A1 - Hüsken, Götz T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-556367 SP - 1 EP - 12 AN - OPUS4-55636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hüsken, Götz A1 - Strangfeld, Christoph A1 - Robens-Radermacher, Annika A1 - von Werder, Julia A1 - Weigel, Sandra A1 - Mezhov, Alexander T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 3: Innovative Technologien N2 - Innovationen sind der Treiber des technologischen Fortschritts. Durch die Anwendung innovativer Technologien, Produktionsverfahren und neuer Materialien können Effizienzsteigerungen erzielt werden, die sowohl zu einer Kosten- als auch Materialreduzierung führen können. Gerade vor dem Hintergrund einer nachhaltigen Entwicklung sind Innovationen der Schlüssel zu einem verantwortungsvollen Umgang mit Ressourcen und Rohstoffen. Im Rahmen des 63. DAfStb-Forschungskolloquiums (Tagungsband: DOI 10.26272/opus4-61338) an der BAM wurden innovative Ansätze im Bereich effizienter Fertigungstechnologien und neuer Materialien vorgestellt, die nachfolgend kurz zusammengefasst werden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Additive Fertigung KW - Biorezeptive Oberflächen KW - Biopolymere PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 134 EP - 135 PB - concrete content UG CY - Schermbeck AN - OPUS4-63069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kocherla, Amarteja A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Embedded Sensors for Quality Control and Structural Integrity Monitoring of Large-scale 3DCP Structures N2 - In extrusion-based 3D concrete printing (3DCP), addressing challenges related to safety, reliability, and quality control is crucial for widespread adoption. Yet current limitations in monitoring material properties during and after printing hinder the development of effective 3DCP guidelines. Therefore, the development of an inline sensing system capable of real-time monitoring and adjustment of process parameters is necessary to overcome these challenges. Building upon an existing inline sensing system developed by BAM, which currently monitors material properties during printing and the geometry of the print post-extrusion, this study extends its capabilities to post-extrusion monitoring using embedded piezoelectric (PZT) sensors. These PZT sensors provide localized measurements of material changes through electrical impedance (EI) measurements without disrupting the printing process. By embedding these sensors in 3D printed structures, continuous monitoring is achieved from layer deposition through 1-day of hydration. To achieve this, initially, PZT sensors were developed with multiple layers of protective coatings. Two different 3D printed mixtures, each with different hydration behaviors, were utilized, and PZT sensors were strategically placed between printed layers to maintain their integrity. EI measurements were collected continuously from printing through 1 day of hydration. Analysis of amplitude and frequency changes in the EI response spectrum provided insights into material behavior post-printing. The study highlights how continuous monitoring of frequency and conductance can track structural builtup and property development of the material. Rapid changes in conductance measurements, immediately post-printing indicate swift structural built-up, while key hydration phases are reflected in frequency measurements. T2 - 34th Annual Conference and Exhibition on Non Destructive Evaluation & Enabling Technologies CY - Chennai, India DA - 12.12.2024 KW - Embedded Sensors KW - 3D Concrete Printing KW - Quality Control KW - Inline Sensing KW - Structural Integrity PY - 2025 SP - 1 EP - 8 PB - Springer Nature CY - Heidelberg AN - OPUS4-65305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Hüsken, Götz A1 - Gründer, Klaus-Peter A1 - Kadoke, Daniel ED - Bohse, Jürgen ED - Purschke, Matthias T1 - Analyse der Schadensmechanismen biegebeanspruchter Stahlbetonbalken mittels zerstörungsfreier Prüftechniken N2 - Der durch Kräfte senkrecht zur Stabachse belastete Balken ist eines der Haupttragelemente des Stahlbetonbaus. Biegebalken finden unter anderem Anwendung in Form von Brückenträgern oder Unterzügen. Die bei maximaler Beanspruchung auftretenden Versagensformen unterteilen sich dabei in Biege- und Querkraftversagen (Schubversagen). Ein Versagen des Balkens kann je nach Versagensmechanismus mit oder ohne Vorankündigung erfolgen. Gebräuchliche Bemessungskonzepte der Baupraxis zur Dimensionierung entsprechender Tragelemente zielen auf ein Versagen mit ausreichender Vorankündigung (große Verformungen oder breite Risse) ab, wie es z.B. beim sekundären Biegedruckversagen entsteht. Für die Zustandsüberwachung von Bauwerken (z.B. Brücken) mittels zerstörungsfreier Prüftechniken sind fundierte Kenntnisse zu den bei Biegebeanspruchung auftretenden Schadensmechanismen erforderlich. Im Rahmen eines BAM-internen Projektes sollen durch praxisnahe Untersuchungen an einer brückenähnlichen Referenzstruktur unterschiedliche auf das Tragwerk einwirkende thermische und mechanische Belastungen untersucht werden und in die Entwicklung eines Monitoringsystems einfließen. Anhand der aus Biegeversuchen vorliegenden Ergebnisse wird der Einsatz unterschiedlicher Methoden der zerstörungsfreien Materialprüfung gezeigt und deren Anwendbarkeit für die Analyse des Verformungsverhaltens von Stahlbetonbalken diskutiert. Hierzu wurde das Verformungsverhalten eines Stahlbetonbalkens (L = 2,75 m) in einem Vierpunkt-Biegeversuch im Labormaßstab untersucht. Das Hauptaugenmerk liegt dabei auf der Charakterisierung der ausschlaggebenden Versagensmodi durch die einzelnen zerstörungsfreien Prüfverfahren und der Vergleich zu klassischen Messmethoden (z.B. Verformungsmessung mittels induktiver Wegaufnehmer (IWA)). Die Biegeversuche wurden dazu durch Schallemissionsanalyse (SEA) und optische Verformungsanalyse mittels Stereo-Fotogrammetrie (SF) und Bildkorrelationsverfahren (BKV) begleitet. T2 - 21. Kolloquium Schallemission CY - Fulda, Germany DA - 09.03.2017 KW - Optische Verformungsanalyse KW - Rissbildung KW - Schallemission KW - Stahlbeton KW - Tragverhalten bei Biegebeanspruchung PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-393617 SN - 978-3-940283-82-5 VL - 59 SP - 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-39361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz A1 - Wagner, L.-C. A1 - Gluth, Gregor A1 - Pirskawetz, Stephan A1 - Kühne, Hans-Carsten T1 - Application of Steel Fibres in Alkali-Activated Mortars N2 - Alkali-activated materials are ideal for the repair of concrete structures in harsh environmental conditions due to their high durability in chemically aggressive environments. However, slag-based mortars, in particular, are prone to shrinkage and associated cracks. In this respect, the application of steel fibres is one solution to reduce the formation of shrinkage induced cracks and to improve post cracking behaviour of these mortars. This study investigated the influence of two different types of steel fibres on the tensile properties of two alkali-activated mortars. Direct tensile tests and single fibre pull-outs were performed to analyse the determining failure modes both on macro and micro scale. Mechanical testing was accompanied by non-destructive testing methods such as digital image correlation and acoustic emission for a detailed analysis of the fracture process. T2 - Local Mechanical Properties - LMP 2019 CY - Prague, Czech Republic DA - 06.11.2019 KW - Alkali-activated materials KW - Fibre pull-out KW - Steel fibres KW - Tensile strength PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509291 UR - https://ojs.cvut.cz/ojs/index.php/APP/article/view/6695 DO - https://doi.org/10.14311/APP.2020.27.0090 VL - 27 SP - 90 EP - 95 CY - Prague, Czech Republic AN - OPUS4-50929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hüsken, Götz A1 - Brouwers, H.J.H. T1 - On the early-age behavior of zero-slump concrete N2 - This paper presents experimental investigations and analyses on the early-age-behavior of zero-slump concrete, such as compaction behavior and green-strength. First, the influence of the granulometric properties of the fines is discussed in detail. For this purpose, the early-age behavior of two different fines (quartz flour and fly ash) is investigated by means of the intensive compaction test (IC-test). The tests on the influence of the fines focus on effects caused by differences in the particle shape and the use of a plasticizing admixture. The conducted tests on the compaction behavior of the fines and their corresponding green-strength are extended to continuously graded granular mixes. Here, the influence of optimized particle packing on the early-age behavior is presented and a comparison on the basis of the aforementioned quartz flour and fly ash is made. In this consideration, experimental investigations on the early-age behavior of a zero-slump concrete mix and possible effects on the hardened concrete properties are included. KW - Zero-slump concrete (A) KW - Green-strength (C) KW - Compaction behavior (A) KW - Intensive compaction test (C) PY - 2012 DO - https://doi.org/10.1016/j.cemconres.2011.11.007 SN - 0008-8846 SN - 1873-3948 VL - 42 IS - 3 SP - 501 EP - 510 PB - Pergamon Press CY - New York, NY AN - OPUS4-26078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercia, G. A1 - Spiesz, P. A1 - Hüsken, Götz A1 - Brouwers, H.J.H. T1 - Chloride intrusion and freeze-thaw resistance of self-compacting concrete with two different nano-SiO2 N2 - In this study two different types of nano-SiO2 were applied in self-compacting concrete (SCC), both having similar particle size distributions (PSD) but produced in two different processes (pyrogenic and colloidal precipitation). The influence of nano-SiO2 on transport phenomena in SCC was investigated using the accelerated rapid chloride migration test at different ages (28 and 91 days) as well as the long-term diffusion test. The freeze-thaw resistance, expressed by the scaling factor (Sn), was also studied. Additionally, the microstructural characteristics of the hardened concretes were investigated by FEG-SEM and MIP analyses. The obtained results demonstrate that the addition of 3.8% bwoc of nano-SiO2 improves the SCC durability due to the refinement of the microstructure and the reduction in the connectivity of the pores. Additionally, a small difference in the reactivity of both types of applied nano-SiO2 additives was demonstrated. T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 12.09.2012 KW - Nano-SiO2 KW - Concrete KW - Self compacting KW - Durability KW - Chloride and freeze-thaw KW - Nano-silica PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-0123 EP - 2-0136 AN - OPUS4-26542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quercia, G. A1 - Hüsken, Götz A1 - Brouwers, H.J.H. T1 - Water demand of amorphous nano silica and its impact on the workability of cement paste N2 - This paper addresses the characterization of six different amorphous silica samples with respect to their application in cement paste. Different mixes are compared and analyzed using the mini spread-flow test. Also the granular properties, different void fraction states of packing and distribution moduli q are analyzed and compared using a mix design tool. A deformation coefficient is derived from the spread-flow test, which correlates with the value of specific surface area computed from the particle size distribution, and intrinsic density of the samples. Finally, the thickness of a constant water layer of 25 nm around the particles is computed at the onset of flowing. The granular analysis demonstrated that it is possible to decrease the water demand of the cement paste when nanoparticles are added and the resulting grading follows the modified Andreasen and Andersen curve (q = 0.5), and the concentration of nano silica is less than 5% bwoc. KW - Nano silica (D) KW - Particle size distribution (B) KW - Surface area (B) KW - Water demand (A) KW - Workability (A) PY - 2012 DO - https://doi.org/10.1016/j.cemconres.2011.10.008 SN - 0008-8846 SN - 1873-3948 VL - 42 IS - 2 SP - 344 EP - 357 PB - Pergamon Press CY - New York, NY AN - OPUS4-26079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -