TY - CONF A1 - Weise, Frank A1 - Müller, U. A1 - Hüsken, Götz A1 - Gardei, Andre T1 - Begutachtung Berliner Tuffsteinfassaden - Turmruine der Kaiser-Wilhelm-Gedächtniskirche und Charlottenburger Tor N2 - Am Ende des 19. und zu Beginn des 20. Jahrhunderts wurden auch in Berlin vermehrt Bauwerke mit einer Fassadenverblendung aus Eifeler Tuffsteinen errichtet. Die Eifeler Tuffsteine zeichnen sich aufgrund ihrer hohen Porosität einerseits durch eine gute Verarbeitbarkeit aus. Andererseits sind sie nur schwach gebunden und besitzen deshalb eine geringe Verwitterungsbeständigkeit. T2 - Workshop Kulturguterhaltung - Vom Dampfkessel zu Nanomaterialien CY - Berlin, Germany DA - 17.11.2021 KW - Fassade KW - Tuffstein KW - Schalenbildung PY - 2021 SN - 2567-1251 VL - 3 SP - 107 EP - 123 PB - Druckerei G. Bohm CY - Berlin AN - OPUS4-54461 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz T1 - Bemessung und Ausführung von Groutverbindungen nach DIN 18088-5 N2 - Die Grout-Verbindung stellt die Nahtstelle zwischen Gründungsbauwerk und aufgehender Tragstruktur sicher. Die Funktion und Dauerhaftigkeit dieser Verbindung ist essentiell für die sichere Betriebsphase von Offshore-Windenergieanlagen. Die Bemessung der Grout-Verbindung stellt aktuell weitgehendes Neuland ohne Langzeiterfahrung dar. Gleichzeitig sind die Bedingungen bei der Montage Offshore sehr schwierig und die eingesetzten Materialien sind aufgrund ihrer technischen Merkmale in Verbindung mit den Verarbeitungsbedingungen nicht unproblematisch. Demzufolge stellen Grout-Verbindungen ungeregelte Bauarten und die hierfür verwendeten Mörtel (Grouts) ungeregelte Bauprodukte dar. Im Rahmen der Genehmigung ist daher beim Bundesamt für Seeschifffahrt und Hydrographie (BSH) als zuständiger Genehmigungsbehörde für jedes Bauvorhaben eine projektbezogene Zustimmung im Einzelfall (ZiE) zu beantragen. Vor diesem Hintergrund sollte im DIN-Arbeitsausschuss NA 005-51-07 AA "Windenergieanlagen" eine geschlossene Normenreihe für Tragstrukturen von Windenergieanlagen und Plattformen erarbeitet werden. Anhand der Normenreihe soll allen bei der Planung, Errichtung und dem Betrieb von Windkraftanlagen Beteiligten ein Regelwerk für Bemessung, Baustoffe und deren Verwendung zur Verfügung gestellt werden. Ein Verweis auf die Normenanforderungen bzgl. der stofflichen Anforderungen, Bemessung und Ausführung durch den betreffenden BSH-Standard ist möglich, da eine ZiE weiterhin notwendig ist. Jedoch kann der Genehmigungsprozess aufgrund der vereinheitlichten Randbedingungen vereinfacht werden. Nach der erfolgreichen nationalen Einführung der DIN 18088 soll die Harmonisierung auf europäischer Ebene erfolgen. T2 - Offshoretage 2017 CY - Heiligendamm, Germany DA - 15.03.2017 KW - Grout-Verbindung KW - DIN 18088-5 KW - Offshore-Windenergieanlagen PY - 2017 AN - OPUS4-39634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Hüsken, Götz T1 - Betonkorrosion und Betoninstandsetzung vor dem Hintergrund der DIN EN 1504 T2 - Bauen im Bestand CY - Northeim DA - 2014-11-20 PY - 2014 AN - OPUS4-32423 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Larcher, M. A1 - Arrigoni, M. A1 - Bedon, C. A1 - van Doormaal, A. A1 - Haberacker, C. A1 - Hüsken, Götz A1 - Millon, O. A1 - Saarenheimo, A. A1 - Solomos, G. A1 - Thamie, L. A1 - Valsamos, G. A1 - Williams, A. A1 - Stolz, A. T1 - Design of blast-loaded glazing windows and facades: a review of essential requirements towards standardization N2 - The determination of the blast protection level of laminated glass windows and facades is of crucial importance, and it is normally done by using experimental investigations. In recent years numericalmethods have becomemuch more powerful also with respect to this kind of application. This paper attempts to give a first idea of a possible standardization concerning such numerical simulations. Attention is drawn to the representation of the blast loading and to the proper description of the behaviour of the material of the mentioned products, to the geometrical meshing, and to the modelling of the connections of the glass components to the main structure.The need to validate the numerical models against reliable experimental data, some of which are indicated, is underlined. KW - Standardization KW - Facades KW - Glazing windows KW - Blast-load KW - Design PY - 2016 DO - https://doi.org/10.1155/2016/2604232 SN - 1687-8094 VL - 2016 SP - Article 2604232, 1 EP - 14 PB - Hindawi Publishing Corporation AN - OPUS4-37124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hüsken, Götz A1 - Brouwers, H.J.H. T1 - On the early-age behavior of zero-slump concrete N2 - This paper presents experimental investigations and analyses on the early-age-behavior of zero-slump concrete, such as compaction behavior and green-strength. First, the influence of the granulometric properties of the fines is discussed in detail. For this purpose, the early-age behavior of two different fines (quartz flour and fly ash) is investigated by means of the intensive compaction test (IC-test). The tests on the influence of the fines focus on effects caused by differences in the particle shape and the use of a plasticizing admixture. The conducted tests on the compaction behavior of the fines and their corresponding green-strength are extended to continuously graded granular mixes. Here, the influence of optimized particle packing on the early-age behavior is presented and a comparison on the basis of the aforementioned quartz flour and fly ash is made. In this consideration, experimental investigations on the early-age behavior of a zero-slump concrete mix and possible effects on the hardened concrete properties are included. KW - Zero-slump concrete (A) KW - Green-strength (C) KW - Compaction behavior (A) KW - Intensive compaction test (C) PY - 2012 DO - https://doi.org/10.1016/j.cemconres.2011.11.007 SN - 0008-8846 SN - 1873-3948 VL - 42 IS - 3 SP - 501 EP - 510 PB - Pergamon Press CY - New York, NY AN - OPUS4-26078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Weise, Frank A1 - Hüsken, Götz T1 - Ringversuch zum statischen Spaltzugversuch nach AL Sp-Beton N2 - Für die rechnerische Dimensionierung der Betondecken im Oberbau von Verkehrsflächen für den Neubau sowie die Erneuerung nach RDO-Beton 09 ist die statische Spaltzugfestigkeit an der unteren und oberen Bohrkernscheibe entsprechend der Vorgaben der AL Sp-Beton zu bestimmen. Aufgrund der unzureichenden Kenntnis der Präzision dieses Prüfverfahrens wurden, basierend auf dem Entwurf des FGSV-Merkblatts zur statistischen Auswertung von Prüfergebnissen, mit einem breit aufgestellten Ringversuch die statistischen Kennwerte an Labor- und Bestandsbetonen unter Vergleich- und Wiederholbedingungen ermittelt. Zur möglichst guten statistischen Absicherung nahmen an dem Ringversuch dreizehn erfahrene Prüfstellen teil, die vorab einem Audit unterzogen wurden. Zur Abdeckung des vielschichtigen Einsatzes des Prüfverfahrens erfolgte der Ringversuch an acht Prüflosen, die sowohl die Erst-/ Eignungsprüfung und Übereinstimmungskontrolle bei Neubaumaßnahmen, als auch die Restsubstanzbewertung von Betonfahrbahnplatten berücksichtigen. Zur Bewertung des Materialeinflusses wurde zusätzlich ein Prüflos mit Labormörtel untersucht. Die Probenvorbereitung erfolgte zentral an der BAM. Zur Sicherstellung einheitlicher Prüfbedingungen bei den Prüfstellen wurde zusätzlich eine detaillierte Standardarbeitsanweisung erarbeitet, die partiell bereits Eingang in das Normenwerk gefunden hat. Bei der Plausibilitätsprüfung aller prüflosspezifischen Einzelwerte der Spaltzug- und Druckfestigkeit wurden vereinzelt sowohl Ausführungsfehler als auch Übertragungs- und Tippfehler festgestellt. Der sich anschließende Lilliefors-Test zeigt, dass die ermittelten Einzelwerte bis auf wenige Aus-nahmen normalverteilt sind und damit die Voraussetzungen für die statistische Auswertung gegeben sind. Mittels grafischer Darstellung der Mandel’s h- und k-Werte wurden die Auffälligkeiten hinsichtlich der Mittelwerte und Varianzen prüflosspezifisch für die einzelnen Prüfstellen visualisiert und anschließend einige von ihnen mittels Grubbs- und Cochran-Test als Ausreißer identifiziert. Nach Ausreißerelimination wurde mit dem klassischen Verfahren bei der Spaltzugfestigkeit der geringste Variationskoeffizient unter Vergleich- und Wiederholbedingungen bei der Erst-/Eignungsprüfung mit 6,2 und 6,4 Prozent ermittelt. Bei einer Verminderung des Materialeinflusses durch die Verwendung eines Labormörtels verbessern sich die statistischen Kennwerte auf 4,5 und 5,3 Prozent. Mit 8,2 und 9,5 Prozent beziehungsweise 8,6 und 9,5 Prozent werden bei der Restsubstanzbewertung von Wasch- und Unterbetonen die höchsten Werte bestimmt. Das robuste Auswerteverfahren (ohne Eliminierung der Ausreißer) nach dem Entwurf des FGSV-Merkblatts zur statistischen Auswertung von Prüfergebnissen erwies sich in der Form als ungeeignet und bedurfte einer Überarbeitung. Bezüglich der vergleichend mit klassischen und robusten Verfahren gewonnenen Kennwerte ist festzustellen, dass bei sehr homogenen Messergebnissen eines Prüfloses beide Verfahren nahezu die gleichen statistischen Kennwerte liefern. Bei der Eliminierung von Ausreißern sind die Ergebnisse des robusten Verfahrens in der Regel etwas größer als die des klassischen Verfahrens. Die begleitenden vertiefenden Untersuchungen bei der Spaltzugprüfung mit innovativen Prüftechniken lieferten wertvolle Erkenntnisse zur Bewertung der Prüfeinflüsse. N2 - The computational design of concrete pavements according to the requirements of the RDO-Beton 09 requires the splitting tensile strength to be determined according to specifications of the AL Sp-Beton. However, detailed information on the precision of the described test procedure is missing. Therefore, a round robin test was set up in order to determine the statistical parameters of the prescribed splitting tensile strength test on laboratory concrete and cores extracted from concrete pavements in terms of repeatability and reproducibility. 13 testing institutes have been involved in the round robin test to guarantee a representative coverage of the sector. The selected testing institutes have been audited prior the round robin test in order to ensure their capabilities. The round robin test was divided into 8 testing lots for covering the broad field of possible applications. Thereby, the testing lots cover both the initial testing of concrete and quality control of new construction. The latter case implies also the assessment of existing concrete pavements. Additionally, a cementitious mortar was designed in order to consider the influence of the material, such as maximum grain size, on the test procedure. The samples were prepared at BAM to guarantee a uniform sample preparation. Furthermore, a standard operating procedure was prepared to assure constant test conditions at the testing institutes. This standard operating procedure is already partly considered by the corresponding standard. A revision of the data reported by the testing institutes revealed that execution errors, transcription errors as well as typing errors occurred. However, a Lilliefors-Test was conducted to verify the Gaussian distribution of the reported test data and to allow the further statistical analysis. Only view data sets do not follow a Gaussian distribution, has no remarkable influence on the obtained statistical data. By means of the graphical illustration of Mandel’s h- and k-values, abnormalities of the arithmetic mean and variance are depicted. These apparent abnormalities can be identified as outliers using the Grubbs and Cochran test. After eliminating the identified outliers, the corresponding statistical parameters have been determined using the classical method for data analysis. The lowest coefficient of variation that was determined for the splitting tensile strength by using the classical method for assessment of the repeatability and reproducibility of the test procedure amounts to 6.2 and 6.4%, respectively, for the initial testing of concrete. Reducing the material influence by using a cementitious mortar, the corresponding statistical parameters were reduced to 4.5 and 5.3%. On the contrary, the highest statistical values were obtained for the assessment of existing concrete pavements. Here, values of 8.2 and 9.5% were obtained for the exposed aggregate concrete and 8.6 and 9.5% for the subconcrete, respectively. The robust method for data analysis (without elimination of outliers) according to the draft version of the technical bulletin of the FGSV turned out to be inappropriate and required, therefore, a revision. Comparing the statistical parameters obtained by the classical and robust method used for data analysis it can be stated that both methods result in nearly identical values for homogeneous data sets without outliers. Considering outliers in the existing data sets, the statistical parameters obtained by the robust method are slightly higher than the values obtained by the classical method with elimination of outliers. The additional investigations on the splitting tensile strength using innovative test procedures provided valuable findings for the assessment of test results. KW - Verfahrenspräzision KW - Betonfahrbahndecke KW - Prüfverfahren AL Sp-Beton KW - Spaltzugfestigkeit KW - Ringversuch PY - 2022 SN - 978-3-95606-688-7 SN - 0943-9323 VL - Straßenbau Heft S 178 SP - 1 EP - 90 PB - Fachverlag NW in der Carl Ed. Schünemann KG CY - Bremen AN - OPUS4-54957 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shamsuddoha, Md A1 - Hüsken, Götz A1 - Baeßler, Matthias A1 - Kühne, Hans-Carsten A1 - Thiele, Marc T1 - Critical factors affecting the capacity of cylindrical grouted connections in offshore energy structures N2 - Current trend suggests that global energy consumption will increase in the future. This growing energy demand and advancement of technology lead to explore all potential offshore fossil and non-fossil energy sources, necessitating erection of exploration and production structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with their maintenances. Cylindrical grouted joints provide suitable connections between steel substructure and foundation in these offshore platforms and wind structures especially monopiles for ease of installation. However, these are composite connections with exterior sleeve, interior pile and infill grout. The capacity of these connections is affected by number of factors. The literature over last four decades by numerous researchers has shown the development of these connections with increasingly higher capacities and influences on these capacities due to various factors. This paper provides a comprehensive review on the factors affecting the connection capacity along with technical challenges for the future. Critical aspects and shortcomings of the current connection systems and potential solutions may be sought after for these issues are also discussed. T2 - 36th International Conference on Ocean, Offshore and Arctic Engineering CY - Trondheim, Norway DA - 25.06.2017 KW - Offshore wind energy KW - Grouted connection KW - Joint capacity KW - Shear keys PY - 2017 SN - 978-0-7918-5766-3 DO - https://doi.org/10.1115/OMAE2017-62510 VL - 3B SP - UNSP V03BT02A037, 1 EP - 10 AN - OPUS4-42387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shamsuddoha,, Md A1 - Hüsken, Götz A1 - Pirskawetz, Stephan A1 - Baeßler, Matthias A1 - Kühne, Hans-Carsten A1 - Thiele, Marc T1 - Remediation of Cracks Formed in Grouted Connections of Offshore Energy Structures under Static Loads N2 - The future energy demand necessitates the exploration of all potential energy sources both onshore and offshore. Global trend has shifted towards offshore energy, which can be obtained from either carbon intensive or renewable options, hence requiring structures such as rigs, platforms, and monopiles. Most of these structures adopt easily installable construction techniques, where lower foundation need to be connected with the super structure by mean of grouted composite joints. Generally, these composite connections have exterior sleeve, interior pile and infill grout. Being located in remote offshore conditions, connections can experience considerable adverse loading during their lifetimes. Degradations were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites may often be proven difficult, which eventually leads to reduced capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs in the future. This study aims at characterizing the nature of crack generation in grouted connections and thereby identifying the potential of repair using suitable repair material. Scaled grouted joints were manufactured using a novel mold, and connections were loaded under static load to visualize the main failure pattern. The failure mechanism and loading capacity are found compatible to previous results from earlier literature. Grouted connection was then repaired using cementitious injectable grout. The effectiveness of the repair system is also discussed. T2 - Twenty-eighth (2018) International Ocean and Polar Engineering Conference CY - Sapporo, Japan DA - 10.06.2018 KW - Offshore KW - Energy KW - Grouted Connection KW - Cracks KW - Repair KW - Rehabilitation PY - 2018 SP - 120 EP - 126 AN - OPUS4-45227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Viefhues, Eva A1 - Ünal, Murat A1 - Hüsken, Götz A1 - Wellershoff, F. A1 - Mehdianpour, Milad T1 - Zementgebundenes Crashmaterial für Schutzbauteile in explosionsbeanspruchten Fassaden N2 - Die Forderung, für repräsentative Bauwerke wie Botschaften und Flughäfen auch außergewöhnliche Lasten aus Explosion zu berücksichtigen, wurde in jüngerer Vergangenheit zunehmend gestellt. Das aufgrund dieser Lasten zu erwartende Schadensausmaß kann durch den Einsatz von energiedissipierenden Schutzbauteilen in der Fassadenbefestigung begrenzt werden. Die Dissipation der Explosionsenergie in den Schutzbauteilen kann beispielsweise über ein Crashmaterial erfolgen. In diesem Aufsatz werden Untersuchungen an zementgebundenen Materialien, die diesem Zweck dienen sollen, vorgestellt. Der Einfluss unterschiedlicher Zusätze auf die für ein Crashmaterial maßgebenden Eigenschaften wird in einer Parameterstudie untersucht. Als besonders geeignet wird ein Material identifiziert, bei dem die Zugabe eines Gasbildners das Matrixgefüge im Hinblick auf das gewünschte Kraft-Verformungs-Verhalten positiv verändert. Dynamische Versuche mit diesem Material geben Aufschluss über dessen Komprimierungsverhalten bei hohen Stauchraten.----------------------------------------------------------------------------------------------------------------------------------------------- In the past few years public awareness of the need to protect structures against blast effects has risen. Energy dissipating protective components placed at the façade connectors allow protecting people in the building as well as the primary building structure from damage due to blast loads. One possibility to dissipate the blast energy is using protective components with crash material. This paper presents tests on cementitious crash materials studying the effect of different additives to the compression-behavior of the material. Additional experiments enable analyzing the material behavior under static and dynamic test conditions. KW - Explosionsbeanspruchung KW - Energiedissipation KW - Fassadenverankerung KW - Materialkennlinie KW - Crashmaterial KW - Crashkörper KW - Energy dissipation KW - Façade connector KW - Material behavior KW - Crash-material KW - Entwurf und Konstruktion KW - Baustoffe KW - Building materials KW - Conception and design KW - Blast loads PY - 2014 DO - https://doi.org/10.1002/bate.201400041 SN - 0932-8351 SN - 1437-0999 SN - 0005-6820 SN - 0341-1052 SN - 0932-6359 VL - 91 IS - 8 SP - 567 EP - 571 PB - Ernst & Sohn CY - Berlin AN - OPUS4-31343 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quercia, G. A1 - Van der Putten, J.J.G. A1 - Hüsken, Götz A1 - Brouwers, H.J.H. T1 - Photovoltaic's silica-rich waste sludge as supplementary cementitious material (SCM) N2 - Waste sludge, a solid recovered from wastewater of photovoltaic-industries, composes of agglomerates of nano-particles like SiO2 and CaCO3. This sludge deflocculates in aqueous solutions into nano-particles smaller than 1 µm. Thus, this sludge constitutes a potentially hazardous waste when it is improperly disposed. Due to its high content of amorphous SiO2, this sludge has a potential use as supplementary cementitious material (SCM) in concrete. In this study the main properties of three different samples of photovoltaic's silica-rich waste sludge (nSS) were physically and chemically characterized. The characterization techniques included: scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), nitrogen physical adsorption isotherm (BET method), density by Helium pycnometry, particle size distribution determined by laser light scattering (LLS) and zeta-potential measurements by dynamic light scattering (DLS). In addition, a dispersability study was performed to design stable slurries to be used as liquid additives for the concrete production on site. The effects on the hydration kinetics of cement pastes by the incorporation of nSS in the designed slurries were determined using an isothermal calorimeter. A compressive strength test of standard mortars with 7% of cement replacement was performed to determine the pozzolanic activity of the waste nano-silica sludge. Finally, the hardened system was fully characterized to determine the phase composition. The results demonstrate that the nSS can be utilized as SCM to replace portion of cement in mortars, thereby decreasing the CO2 footprint and the environmental impact of concrete. KW - Nano-silica sludge (D) KW - Supplementary cementitious materials (D) KW - Pozzolanic index (C) KW - Mortar (E) PY - 2013 DO - https://doi.org/10.1016/j.cemconres.2013.08.010 SN - 0008-8846 SN - 1873-3948 VL - 54 SP - 161 EP - 179 PB - Pergamon Press CY - New York, NY AN - OPUS4-30384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -