TY - JOUR A1 - Otremba, Frank A1 - Heming, Frank T1 - Rückendeckung N2 - Sicherheit - Trotz des Spotts anderer Europäer, 'Auffahrunfälle gebe es nur in Deutschland', wird das Ziel eines Anfahr- statt Unterfahrschutzes für das Tankfahrzeugheck hierzulande weiter verfolgt. PY - 2013 SN - 0016-5808 VL - 3 SP - 14 EP - 17 PB - Storck CY - Hamburg AN - OPUS4-27745 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Borch, Jörg-Peter A1 - Otremba, Frank A1 - Balke, Christian A1 - Burghardt, Frank T1 - Sicherheit von Flüssiggasflaschen im Unfallfeuer N2 - Neben herkömmlichen Stahlflaschen, die seit Jahrzehnten in fast unveränderter Bauform für Flüssiggase (Propan-Butan-Gemische) eingesetzt werden, etablieren sich immer mehr Flaschen aus Faserverbundwerkstoffen (GFK) mit einer geringeren Masse. Die Bundesanstalt für Materialforschung und -prüfung (BAM) wurde beauftragt, das Verhalten dieser Gasflaschen unter den extremen Bedingungen eines Unfallfeuers zu untersuchen. In einem Brandprüfstand der BAM auf dem Testgelände Technische Sicherheit (TTS) in Horstwalde wurden deshalb beide Typen von Propangasflaschen einem simulierten Unfallfeuer ausgesetzt. KW - Gefahrgut KW - Flüssiggas KW - Flaschen KW - Unfallfeuer KW - Druckgefäße KW - Gefahrguttransport PY - 2013 SN - 2191-0073 VL - 3 IS - 11/12 SP - 44 EP - 47 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-29720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sklorz, Christian A1 - Otremba, Frank A1 - Balke, Christian T1 - BLEVE performance of fire protection coating systems on dangerous goods tanks in a test fire N2 - How can the risk of a BLEVE be reduced? That is the main question based on different research projects. In various large scale fire tests fire protection coating systems were used of different manufacturers. The degree of the coating as well as the layer thickness and the processing were varied. These experimental configurations were partly tested with and without pressure relief valve. The pressure relief valves were not protected again the thermal Load from the test fire. The ambition is to find a minimum of the thickness from the fire protection coating witch delay a BLEVE up to 90 minutes. Here are given the most interested configurations of tanks in fire and a description of the test-rigs. KW - BLEVE KW - Fire protection coating KW - Isolation KW - Test rigs KW - Large scale fire test PY - 2013 DO - https://doi.org/10.12720/ijmse.1.2.90-93 SN - 2315-4527 VL - 1 IS - 2 SP - 90 EP - 93 PB - Engineering and technology publishing AN - OPUS4-30124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Otremba, Frank A1 - Romero-Navarrete, José A. A1 - Lozano Guzmán, A. A. T1 - Modelling of a Partially Loaded Road Tanker during a Braking-in-a-Turn Maneuver N2 - This paper describes a theoretical model to simulate the effects of a sloshing cargo on the safety performance of a vehicle that performs a braking-in-a-turn maneuver when travels at a partial fill level. The fundamental assumption of the model consists of the superposition of the effects of two simplified mechanical-analogy models that represent a liquid cargo on a vehicle, including one for the roll motion and another one for the pitch motion. The distinctive characteristics of the mechanical models, however, is that they are based upon a validated formulation to establish the properties of the pendulum (length). The results suggest a small effect of the sloshing cargo on the braking efficiency of the cargo, while the load transfer is moderately affected. However, such results should be put into a perspective, according to which such small variations can represent the avoidance of a rear-end crash or a rollover. In this respect, a specialized ABS system could be considered to improve the performance of such kind of vehicles when performing such maneuvers. Validation of the proposed methodology should be performed as a continuation of this research effort. KW - ABS KW - Braking-in-a-turn maneuver KW - Cargo sloshing KW - Road tankers KW - Load transfer KW - Simulation KW - Turning maneuvers PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-456908 DO - https://doi.org/10.3390/act7030045 VL - 7 IS - 45 SP - 1 EP - 14 PB - MDPI CY - Basel AN - OPUS4-45690 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pötzsch, Sina A1 - Krüger, Simone A1 - Sklorz, Christian A1 - Borch, Jörg A1 - Hilse, Thilo A1 - Otremba, Frank T1 - The fire resistance of lightweight composite tanks depending on fire protection systems N2 - To save weight and resources lightweight tanks with complex geometries made of glass-fibre reinforced plastics (GFRP) are a promising innovation for the transportation of dangerous goods. To realise the use of polymer tanks for such applications, their fire safety must be guaranteed. This paper presents solutions to protect fibre-reinforced plastic tanks from fire. The fire resistance of six GFRP tanks with different fire protection systems was tested in an outdoor full-scale fire test facility according to the regulation stipulated in the ADR (European agreement concerning the national carriage of dangerous goods by road). All tanks feature a complex geometry and a holding capacity of 1100 litres. The fire protection systems are composed of specialised resins as well as two intumescent coatings. All systems had a protective impact. The best results were achieved by the epoxy based intumescent coating, which was able to prolong the time needed to reach 150 °C inside the tank by 20 min. The emergence of a temperature holding point inside the tank due to condensation effects was observed at temperatures around 100 °C. KW - Fire safety composite tanks PY - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0379711218301644 DO - https://doi.org/10.1016/j.firesaf.2018.08.007 SN - 0379-7112 SN - 1873-7226 VL - 100 SP - 118 EP - 127 PB - Elsevier Ltd. AN - OPUS4-45697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fraňa, K. A1 - Attia, S. H. A1 - Otremba, Frank T1 - A numerical simulation of the filling process in the pressure bottle N2 - A filling process of the pressure bottle used for the air storage was investigated by numerical simulations. During the filling process, the temperature was rising up to maximal value and after that started to decline. The good match was found between experimental and numerical results. In order to reproduce the experimental conditions, the process of the filling bottle was controlled by the pressure which varied in time. This filling strategy influenced furthermore the mass flow rate and the air flow velocity. Because of the geometrical symmetry, the simulation was calculated as an axisymmetric problem. KW - Filling procedere KW - Receptacle PY - 2018 UR - http://www.ijmerr.com/index.php?m=content&c=index&a=show&catid=162&id=997 DO - https://doi.org/10.18178/ijmerr.7.5.558-563 SN - 2278-0149 VL - 7 IS - 5 SP - 558 EP - 563 PB - IJMERR CY - Rowland Heights, CA, USA AN - OPUS4-46021 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Borch, Jörg A1 - Otremba, Frank T1 - Der neue Jetfire-Prüfstand der BAM N2 - Die BAM – Bundesanstalt für Materialforschung und -prüfung führt schon seit vielen Jahren auf zwei Brand- prüfständen Brandprüfungen z.B. an Transport- und Lagerbehältern für radioaktive Stoffe oder zur Prüfung von Brandschutzbeschichtungen durch. Als Brandmedium wird auf diesen Prüfständen Flüssiggas (Propan- Butan-Gemisch C) eingesetzt, mit dem die Prüfobjekte simulierten Unfallfeuern ausgesetzt werden. Mit dem neuen Jetfire – Prüfstand der BAM können seit Anfang 2018 diverse Belastungsszenarien nach den Anforde- rungen der ISO22899-1:2007 [1] simuliert werden. KW - Jetfire KW - Prüftstand PY - 2018 UR - https://www.technische-sicherheit.de/ts/article.php?data[article_id]=89195 SN - 2191-0073 VL - 8 IS - 4 SP - 25 EP - 27 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-44814 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Borch, Jörg-Peter A1 - Otremba, Frank T1 - Jetfire-Prüfstand ergänzt die bereits vorhandenen Brandprüfstände N2 - Seit zehn Jahren führt die Bundesanstalt für Materialforschung und -prüfung (kurz: BAM) auf zwei Prüfständen Brandprüfungen z. B. an Transport-und Lagerbehältern für radioaktive Stoffe oder zur Prüfung von Brandschutzbeschichtungen durch. Als Brandmedium wird Flüssiggas (Propan-Butan-Gemisch C) eingesetzt, mit dem die Prüfobjekte simulierten Unfallfeuern ausgesetzt werden. Seit Anfang 2018 verfügt die BAM darüber hinaus auch über einen Jetfire-Prüfstand, der die Anforderungen der ISO 22899-1:2007 1) erfüllt. KW - JetFire KW - Prüfstand PY - 2018 SN - 2191-0073 SP - 28 EP - 30 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-46566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Iancu, O.T. A1 - Erhard, Anton A1 - Otremba, Frank A1 - Sklorz, Christian T1 - Consistency between analytical and finite element predictions for safety of cylindrical pressure vessels at higher temperatures N2 - Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt. KW - Materials testing KW - FEM KW - Plastic instability KW - Limit load analysis KW - Pressure vessel KW - Analytical solution PY - 2014 SN - 0025-5300 VL - 56 IS - 4 SP - 274 EP - 278 PB - Hanser CY - München AN - OPUS4-30722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kocinski, Lilianna A1 - Otremba, Frank A1 - Drousch, Björn T1 - Positions-Bestimmung - Versagensverhalten - Eine Beanspruchungsanalyse für Kunststoff-Kanister mittels der Finite Elemente Methode (FEM) könnte zur Vereinheitlichung der Fallprüfung und Vergleichbarkeit der Ergebnisse beitragen PY - 2009 SN - 0016-5808 VL - 9 SP - 20 EP - 21 PB - Storck CY - Hamburg AN - OPUS4-19824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -