TY - JOUR A1 - Lott, S. A1 - Henrion, A. A1 - Malz, Frank A1 - Kessler, A. A1 - Güttler, B. A1 - Aderjan, R. T1 - Reference measurement procedure for Delta9-tetrahydrocannabinol in serum N2 - An isotope dilution gas chromatography/mass spectrometry (ID-GC/MS) reference measurement procedure for Δ9-tetrahydrocannabinol (THC) in serum was developed and validated. The method complies with the concept of a ratio primary reference measurement procedure. The uncertainty was determined for two concentrations of THC in serum (1 ng/mL and 2.4 ng/mL). The calculation procedure is based on the Guide to the Expression of Uncertainty in Measurement (GUM). The relative expanded uncertainty was found to be less than 2% for both concentration levels, corresponding to a 95% confidence interval. For the reference method, it was shown that the measurement of THC within the concentration range covered by the current threshold values is very accurate. The method has the potential to provide traceability for the methods used in practical forensics. KW - THC KW - Uncertainty of measurement KW - GUM KW - Threshold value KW - Reference material KW - Primary method KW - Quantitative NMR PY - 2008 DO - https://doi.org/10.1007/s00216-008-2065-1 SN - 1618-2642 SN - 1618-2650 VL - 391 IS - 3 SP - 1003 EP - 1010 PB - Springer CY - Berlin AN - OPUS4-17628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, H. S. A1 - Fenchel, M. A1 - Wiggenhauser, Herbert A1 - Maierhofer, Christiane A1 - Krause, Martin A1 - Gardei, André A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Röllig, Mathias A1 - Wöstmann, Jens T1 - Zerstörungsfreie Ortung von Gefügestörungen in Betonbodenplatten N2 - Das Ziel des Forschungsvorhabens „Zerstörungsfreie Ortung von Gefügestörungen in Betonbodenplatten“ bestand in der Entwicklung eines Untersuchungskonzepts zur sicheren Ortung und Erfassung von Gefügestörungen in einseitig zugänglichen Betonplatten durch den kombinierten Einsatz verschiedener zerstörungsfreier Prüfverfahren. Hierfür wurde die Leistungsfähigkeit der folgenden Messverfahren hinsichtlich ihrer Aussageschärfe, Anwendungsgrenzen und Messgeschwindigkeit bei praxisnahen Randbedingungen untersucht: - Impakt-Echo, manuelle Impaktauslösung - Impakt-Echo, automatisierte Impaktauslösung - Ultraschall-Echo mit multistatischem Array - Impuls-Thermografie - Radar Als Versuchskörper dienten sechs liegend hergestellte Betonplatten der Abmessungen 200/200/30 cm aus zwei verschiedenen Betongüten und mit unterschiedlichem Bewehrungsgehalt (Bewehrungsgrade 0 %, 0 ,9 %, 2 ,6 %), von denen vier Platten auf trockenem und zwei Platten auf ständig nass gehaltenem Sand gelagert waren. Alle sechs Platten enthielten jeweils dieselben künstlich eingebrachten Fehlstellen: vier quadratische Kiesnester in unterschiedlicher Tiefe mit Kantenlängen zwischen 10 und 15 cm sowie drei oberflächennahe Hohlstellen (Ø 4/6/8 cm). Zur Erfassung eines möglichen Einflusses des Betonalters wurden die Messungen 4 Tage, 28 Tage sowie 180 Tage nach Herstellung der Platten durchgeführt. Um aus den Untersuchungen einen breiten Nutzen für die Praxis zu erzielen, basierten die eingesetzten Messverfahren auf handelsüblichen Geräten, welche jedoch bezüglich ihres Messprinzips und insbesondere der Datenerfassung und -auswertung weiterentwickelt wurden. Die Fehlstellengröße wurde bewusst klein gewählt. Mit Ausnahme des manuellen Impakt-Echo-Verfahrens, mit welchem unter Verwendung der Originalsoftware des Herstellers keine Fehlstellen nachweisbar waren, zeigten sich alle Messverfahren geeignet, unter verschiedenen Randbedingungen Gefügestörungen zu lokalisieren. Insgesamt wurde jeder Fehlstellentyp von zumindest einem Verfahren bei mindestens zwei Versuchskörpern detektiert. Es konnten jedoch an keiner Betonplatte mit einem einzelnen Messverfahren alle vorhandenen Fehlstellen an allen Messterminen geortet werden. Am häufigsten wurden die beiden großen oberflächennahen Fehlstellen (Hohlstelle Ø 8 cm, Kiesnest 10 cm) erkannt. Am schwersten zu lokalisieren waren die kleine Hohlstelle mit 4 cm Durchmesser sowie die beiden auf der Unterseite gelegenen Kiesnester. Die Untersuchungen zeigen, dass für eine erfolgreiche Anwendung zerstörungsfreier Messverfahren in der Praxis die Auswahl des am besten geeigneten Verfahrens bzw. einer Kombination verschiedener Verfahren jeweils auf die vorliegende Problemstellung abgestimmt sein muss. Für Betonbodenplatten mit hohem Feuchtegehalt (junger Beton) oder starker Bewehrung ist entweder das Ultraschall- oder das Impakt-Echo-Verfahren geeignet. Das Ultraschall-Verfahren wird von hohen Bewehrungsgehalten zwar stärker beeinflusst als das Impakt-Echo-Verfahren, besitzt aber eine bessere Auflösung und ermöglicht auch im oberflächennahen Bereich eine quantitative Bestimmung der Fehlstellentiefe. Das Impakt-Echo-Verfahren kann wegen der niederfrequenten Impulsanregung Fehlstellen erst in größeren Tiefen und mit schlechterer Auflösung nachweisen, ist aber ideal geeignet zur Bestimmung der Plattendicke aufgrund seines signifikanten Rückwandechos. Sowohl das Radar-Verfahren als auch die Impuls-Thermografie können bei hohen Feuchte- und Bewehrungsgehalten nur sehr oberflächennah eingesetzt werden. Bei trockenem Beton und geringen bis mittleren Bewehrungsgehalten liefert das Radar-Verfahren sehr gute Ergebnisse. In kurzer Zeit ermöglicht es eine flächendeckende Ortung der Tiefenlage und Größe von Inhomogenitäten bei guter Auflösungsgenauigkeit. Vorhandene Bewehrung wird deutlich abgebildet, kann aber darunterliegende Fehlstellen verschatten. Alternativ kann die Impuls-Thermografie für die Ortung oberflächennaher Gefügestörungen eingesetzt werden. Das Verfahren eignet sich insbesondere bei Oberflächen, die nicht direkt zugänglich sind, da zwischen Infrarotkamera und Messobjekt nur Sichtkontakt bestehen muss. Die Betongüte hatte bei keinem eingesetzten Verfahren einen erkennbaren Einfluss auf die Messergebnisse. Streng genommen ist dies jedoch nur für den Einfluss des Wasserzementwertes, der Zementart und des Zementgehalts bei gleichbleibender Sieblinie und gleicher Kornart gültig. Bei Verwendung von Leichtzuschlag sind abweichende Ergebnisse denkbar. PY - 2010 SN - 978-3-410-65075-1 SN - 0171-7197 IS - 589 SP - 1 EP - 88 PB - Beuth CY - Berlin AN - OPUS4-22699 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Crail, S. A1 - Reichel, D. A1 - Schreiner, U. A1 - Lindner, E. A1 - Habel, Wolfgang A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Barner, Andreas ED - Casciati, F. T1 - Strain Monitoring of a High Speed Railway Track Using Embedded Fibre-Optic Sensors PY - 2003 SN - 0-471-48980-8 VL - 2 SP - 903 EP - 909 PB - Wiley CY - Chichester AN - OPUS4-2374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasche, K. A1 - Ulm, G. A1 - Herrmann, K. A1 - Krumrey, M. A1 - Ade, G. A1 - Sümpel, J. A1 - Busch, I. A1 - Thomsen-Schmidt, P. A1 - Schädlich, S. A1 - Schindler, A. A1 - Frank, W. A1 - Procop, Mathias A1 - Beck, Uwe T1 - About the calibration of thickness standards on the nanometer scale T2 - 3rd International EUSPEN conference ; 3rd International conference. European Society for Precision Engineering and Nanotechnology ; 4th General meeting. European Society for Precision Engineering and Nanotechnology CY - Eindhoven, The Netherlands DA - 2002-05-26 PY - 2002 SN - 90-386-2883-8 SP - 1 EP - 5 CY - Eindhoven AN - OPUS4-2283 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hasche, K. A1 - Herrmann, K. A1 - Thomsen-Schmidt, P. A1 - Krumrey, M. A1 - Ulm, G. A1 - Ade, G. A1 - Pohlenz, F. A1 - Stümpel, J. A1 - Busch, I. A1 - Schädlich, S. A1 - Frank, W. A1 - Hirsch, D. A1 - Schindler, A. A1 - Procop, Mathias A1 - Beck, Uwe T1 - Ein Beitrag zu kalibrierten Nanometerschichten für unterschiedliche Anwendungsbereiche N2 - Nanotechnologien werden gegenwärtig als leistungsfähige Oberflächentechniken in erheblichem Umfange industriell genutzt. Dabei spielen dünne Schichten und deren Kenndaten eine wesentliche Rolle, z.B. als Röntgenspiegel oder optische und magnetooptische Datenträger. Die Schichtdicke zählt hierbei zu den technologisch wichtigen Parametern. Abgeleitet von Anwenderinteressen, werden für die Röntgenreflektometrie (XRR bzw. GIXR), Elektronenstrahl-Mikroanalyse (EPMA) und Röntgenfluoreszenzanalyse (XRF) einerseits und die Ellipsometrie andererseits zugeschnittene Schichtdickenmaßverkörperungen (SDM) entwickelt, gefertigt und untersucht. Das Ziel ist die Bereitstellung praxistauglicher, kalibrierter SDM, im weiteren Schichtdickennormale (SDN) genannt. SDN sind Maßverkörperungen, für die der Schichtdickenwert mit einer definierten Messunsicherheit bekannt und auf ein metrologisch anerkanntes Längennormal zurückgeführt ist. Berichtet wird über die Herstellung und messtechnische Charakterisierung der beiden spezifischen Varianten von Maßverkörperungen. T2 - 47. Internationales Wissenschaftliches Kolloquium. Technische Universität Ilmenau ; Herbstkonferenz der Gesellschaft für Arbeitswissenschaft ; 6. Workshop Multimedia für Bildung und Wirtschaft CY - Ilmenau, Deutschland DA - 2002-09-23 PY - 2002 UR - http://publica.fraunhofer.de/documents/N-14872.html VL - 47 SP - 568 EP - 569 PB - Techn. Univ. CY - Ilmenau AN - OPUS4-2284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koenders, L. A1 - Hasche, K. A1 - Ulm, G. A1 - Krumrey, M. A1 - Ade, G. A1 - Stümpel, J. A1 - Busch, I. A1 - Thomsen-Schmidt, P. A1 - Schädlich, S. A1 - Schindler, A. A1 - Frank, W. A1 - Beck, Uwe A1 - Procop, Mathias T1 - Über die metrologische Charakterisierung von Schichtdicken Standards im Nanometerbereich T2 - 12th Applied Surface Analysis Workshop ; AOFA 12 CY - --- DA - 2002-09-15 PY - 2002 AN - OPUS4-2285 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Milmann, Boris A1 - Helmerich, Rosemarie A1 - Köpp, Christian A1 - Mielentz, Frank A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Moryson, R.-M. A1 - Samokrutov, A. A1 - Alekhin, S. G. A1 - Alver, Ninel A1 - Sazak, H.-Ö. ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Ultrasound based monitoring system for concrete monolithic objects N2 - Ultrasound sensors should be embedded into concrete for monitoring concrete properties. These new longitudinal wave sensors with a center frequency of 60 kHz were examined regarding their suitability for ultrasonic measurements in concrete structures in terms of emission characteristics, sensitivity and frequency ränge. For the measurement of the radiation patterns, the sensors were embedded vertically and horizontally in concrete cylinders. The directivity pattern was measured using a laser vibrometer. The sensitivity of the sensor was determined in water using different sensors of the same type. It shows changes in the signal amplitude as well as variations in the frequency ränge for different transmitter-receiver combinations. The attenuation of the concrete affects the achievable resolution of the measurements and thus, the maximum possible spacing of the sensors within a concrete element. Experimental tests helped optimizing the distances with respect to the required resolution and the effort of embedding the sensors. The signal attenuation in the concrete was measured in the frequency ränge of 60 kHz in response to various degrees of reinforcement and grain size. For this purpose, the sensors were cast at different distances in the specimens studied. The recorded Signals were evaluated for their amplitude and frequency spectrum. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Ultrasound KW - Concrete KW - Monitoring system KW - Ultrasonic network KW - Embedded sensor PY - 2013 SN - 978-962-367-768-4 SP - 1 EP - 6 AN - OPUS4-29642 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Krause, Martin A1 - Müller, W. A1 - Crail, S. T1 - Zerstörungsfreie Risscharakterisierung in Betonbauteilen mit Ultraschall N2 - Die Risstiefenbestimmung in Festen Fahrbahnen ist hinsichtlich der Dauerhaftigkeit der Konstruktion von wesentlichem Interesse. Im Rahmen eines gemeinsamen Forschungsvorhabens mit der DB AG wurden aus der Literatur bekannte Ansätze bewertet und darauf aufbauend ein Verfahren zur bildgebenden Rissdarstellung entwickelt. Rissüberbrückende Bewehrung sowie Kontaktstellen zwischen den Rissflanken wirken als Schallbrücken und erschweren die Risscharakterisierung, wie bei einem Einsatz an einer Betriebserprobungsstrecke festgestellt wurde. Ein aus der Literatur bekanntes Verfahren der einfachen Laufzeitmessung erwies sich für die Tiefenbestimmung von realen verunreinigten Rissen als ungeeignet. T2 - Fachtagung Bauwerksdiagnose - Praktische Anwendungen Zerstörungsfreier Prüfungen CY - Leipzig, Germany DA - 25.10.2001 PY - 2001 VL - 76-CD SP - 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-1188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Habel, Wolfgang A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Brandes, Klaus A1 - Barner, Andreas A1 - Crail, S. A1 - Reichel, D. A1 - Schreiner, U. A1 - Ecke, W. ED - Inaudi, D. T1 - Strain monitoring of a newly developed precast concrete track for high speed railway traffic using embedded fiber-optic sensors KW - Railway track system KW - Bonding behaviour KW - Fiber-optic sensor KW - Concrete composites PY - 2002 SN - 0-8194-4442-1 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 4694 SP - 259 EP - 264 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-1457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Keidel, Frank A1 - Rühlmann, K. A1 - Jähnichen, S. A1 - Scheller, D. A1 - Scheim, U. ED - Andrianov, K. A. T1 - On the synthesis of siloxanes. XXIII. Synthesis and spectroscopic characterization of 2-functional 1,3-dioxa-2,4,7-trisilacycloheptanes N2 - A series of 2-functional 1,3-dioxa-2,4,7-trisilacycloheptanes was synthesized and characterized by means of 29Si NMR spectroscopy, gas chromatography, high performance liquid chromatography and gas chromatography-mass spectrometry. The signals were assigned to the various configurational isomers. This assignment was confirmed by independent synthesis of individual isomers. The sequence of the NMR signals of the all-cis and trans-trans isomers required for the determination of stereochemistry was found to be the same as that of the respective cyclotrisiloxanes. KW - Cylosiloxanes KW - Synthesis KW - Spectroscopic characterization PY - 1995 DO - https://doi.org/10.1016/0022-328X(95)05586-0 SN - 0022-328X SN - 1872-8561 VL - 505 IS - 1 SP - 29 EP - 36 PB - Elsevier CY - Amsterdam AN - OPUS4-1423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Habel, Wolfgang A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Barner, Andreas A1 - Crail, S. A1 - Reichel, D. A1 - Schreiner, U. A1 - Lindner, E. T1 - Static and dynamic measurements on a newly developed precast concrete track for high speed railway traffic using embedded fiber-optic sensors T2 - International Conference on Force, Mass, Torque, Hardness and Civil Engineering Metrology in the Age Globalization CY - Celle, Germany DA - 2002-09-24 KW - Railway track system KW - Bonding behaviour KW - Fibre-optic sensor KW - Concrete composites PY - 2002 SN - 3-18-091685-0 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 1685 SP - 147 EP - 152 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-1755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ruedrich, J. A1 - Rieffel, Y. A1 - Pirskawetz, Stephan A1 - Alpermann, H. A1 - Joksch, U. A1 - Gengnagel, C. A1 - Weise, Frank A1 - Plagge, R. A1 - Zhao, J. A1 - Siegesmund, S. T1 - Development and assessment of protective winter covers for marble statuaries of the Schlossbrücke, Berlin (Germany) N2 - The present study documents the results of an inter-disciplinary model project that was planned with the aim of developing an innovative winter covering system for marble statuaries located on the Schlossbru¨cke (Berlin). Such a system would need to fulfil the various requirements for structural stability, aesthetics, climate and practical use. This applied research represents the first complex scientific study of the sustainability of a winter covering system. The study is characterised by the use of complex scientific instruments such as special laboratory analysis and numerical simulation tools. The interaction between the environment and the artefacts in connection with the innovative winter covering structures were studied by extensive climatic monitoring. KW - Marble sculptures KW - Marble weathering KW - Winter cover KW - Climate data KW - Numerical simulations PY - 2011 DO - https://doi.org/10.1007/s12665-010-0765-2 SN - 1866-6280 SN - 1866-6299 VL - 63 IS - 7-8 SP - 1823 EP - 1848 PB - Springer CY - Berlin; Heidelberg AN - OPUS4-22363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Siegesmund, S. A1 - Pirskawetz, Stephan A1 - Rieffel, Y. A1 - Gossart, E. A1 - Joksch, U. A1 - Weise, Frank A1 - Plagge, R. A1 - Ruedrich, J. ED - Siegesmund, S. ED - Snethlage, R. T1 - Die Schlossbrücke in Berlin - Via triumphalis N2 - Für die bisher der winterlichen Witterung schutzlos ausgelieferten acht Figurengruppen auf der Schlossbrücke in Berlin wurde innerhalb des vom Landesdenkmalamt Berlin und der Senatsverwaltung für Stadtentwicklung initiierten Forschungsprojektes geprüft, ob und welcher Typ einer Einhausung in der Lage ist, die schädlichen Umwelteinflüsse zu reduzieren. Um den hohen konservatorischen, bauphysikalischen, bautechnischen, künstlerischen und stadträumlichen Anforderungen gerecht zu werden und mögliche Lösungen erstmalig umfassend auf ihre Effektivität zu untersuchen, war die Zusammenarbeit von Denkmalpflegern, Restauratoren, Architekten, Ingenieuren, Geologen, Materialwissenschaftlern und Bauphysikern notwendig. Das durch die Deutsche Bundesstiftung Umwelt (DBU) geförderte Projekt zielte darauf ab, in einem Modellvorhaben mit seinen Partnern, der Technischen Universität Dresden (Institut für Bauklimatik), der Universität Göttingen (Abt. Strukturgeologie und Geodynamik), der Bundesanstalt für Materialforschung und -prüfung (Fachgruppe 7.1, Baustoffe) und unter Beteiligung der Universität der Künste (Fachbereich Konstruktives Entwerfen und Tragwerkslehre) in Berlin, eine innovative und nachhaltige Wintereinhausungskonstruktion auf die besondere Situation der Marmorskulpturen der Schlossbrücke anzupassen und ihre Wirksamkeit zu überprüfen. KW - Marmorverwitterung KW - Denkmalpflege KW - Wintereinhausung PY - 2013 SN - 978-3-95462-060-9 SP - 310 EP - 321 PB - mdv Mitteldeutscher Verlag GmbH CY - Halle/Saale AN - OPUS4-28685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Siegesmund, S. A1 - Pirskawetz, Stephan A1 - Weise, Frank A1 - Plagge, R. A1 - Rieffel, Y. ED - Siegesmund, S. ED - Middendorf, B. T1 - Winter Shelters For Marble Sculptures Of The Schlossbrücke Berlin: Climatic Constraints N2 - The long-term exposure of marble objects leads to a successive deterioration of the rock fabric and may cause severe damage on cultural heritage objects. The magnitude of disintegration depends on the rock fabric as well as on the climatic conditions. Some types of marble show no considerable damage even if they have been exposed in northern Europe for several decades or centuries. In contrast, other marble varieties are showing severe damage after a few years of weathering. The present study shows that marble decay, along with the initial thermal degradation, is mainly influenced by the hygric and thermo-hygric load, respectively. The influence of the rock fabric on the resistivity against weathering is also documented. The factors causing marble decay were compared to extensive climate data, which were collected during a scientific project that was started with the aim to develop a covering system for marble sculptures in Berlin. Based on the hygrothermal material properties of the marble and on the climatic conditions, the heat and moisture Transport inside the material and hence the hygrothermal load changes were calculated with a high spatial resolution. The calculations showed that the temperature and moisture fluctuations inside the material are mainly controlled by the dimensions and orientation of the sculptural elements. The current state of preservation was investigated by two-dimensional ultrasonic tomography. The results show a good correlation to the calculated distribution of the hygrothermal load. Based on this finding, requirements on a protective winter shelter system for the sculptures were defined. The project results show that in addition to protective covers, regular inspection and maintenance combined with regular cleaning ensures an effective and sustainable protection of marble objects in northern Europe. T2 - 14th International Congress on the Deterioration and Conservation of Stone CY - Göttingen, Germany DA - 07.09.2020 KW - Schlossbrücke KW - Marble decay KW - Weathering processes KW - Ultrasound wave velocities KW - Climatic impact KW - Numerical simulation KW - Maintenance PY - 2020 SN - 978-3-96311-172-3 SP - 709 EP - 716 PB - mdv Mitteldeutscher Verlag GmbH CY - Halle (Saale) AN - OPUS4-51916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Thieme-Hack, M. A1 - Berghaus, U. A1 - Brümmer, F. A1 - Elsner, U. A1 - Färber, C. A1 - Frank, D. A1 - Illgas, M. A1 - Kalbe, Ute A1 - Kathage, J. A1 - Leers, A. A1 - Müller, B. A1 - Röger-Göpfert, C. A1 - Russland, H.-J. A1 - Schnabel, B. A1 - Schneider, O. A1 - Schockmann, D. A1 - Schomakers, H. A1 - Schwalbe, D. A1 - Stegemann, D. A1 - van den Berg, T. A1 - Kramps, S. T1 - Fachbericht Kunststoffsportböden - Nachhaltige Kunststoffbelagsauswahl für Sportfreianlagen N2 - Kunststoff- und Kunststoffrasenflächen kommt bei intensiv genutzten Flächen als Allwetterbeläge eine große Bedeutung zu. Sie leisten einen wichtigen Beitrag zur Absicherung eines ganzjähriger Sportangebote. Gerade Kunststoffrasen ist aber in den letzten Jahren häufig in die Kritik geraten, insbesondere durch gefährliche Inhaltsstoffe und andere negative Einflüsse auf die Umwelt. Dies hat bei Bauherren zu einer Verunsicherung geführt und Fragen aufgeworfen, die erst teilweise beantwortet sind. Die Diskussionen rund um diesen Allwetterbelag haben bereits dazu geführt, dass von Seiten der Industrie viel verändert wurde und neue innovative Lösungen gefunden werden. Der Fachbericht stellt eine Handreichung für Fachleute und interessierte Laien dar, um mehr Klarheit besonders hinsichtlich der Umweltanforderungen zu erzielen. KW - Kunststoffsportbeläge KW - Kunstrasen KW - Umweltverträglichkeit KW - Schadstofftransfer KW - Mikroplastik PY - 2022 UR - https://shop.fll.de/de/fachbericht-kunststoffsportboeden-broschuere.html SP - 1 EP - 70 PB - Forschungsgesellschaft Landschaftsentwicklung Landschaftsbau (FLL) CY - Bonn AN - OPUS4-54390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niederleithinger, Ernst A1 - Gardner, S. A1 - Kind, Thomas A1 - Kaiser, R. A1 - Grunwald, Marcel A1 - Yang, G. A1 - Redmer, Bernhard A1 - Waske, Anja A1 - Mielentz, Frank A1 - Effner, Ute A1 - Köpp, Christian A1 - Clarkson, A. A1 - Thompson, F. A1 - Ryan, M. A1 - Mahon, D. T1 - Muon Tomography of the Interior of a Reinforced Concrete Block: First Experimental Proof of Concept N2 - Quality assurance and condition assessment of concrete structures is an important topic world-wide due to the aging infrastructure and increasing traffic demands. Common topics include, but are not limited to, localisation of rebar or tendon ducts, geometrical irregularities, cracks, voids, honeycombing or other flaws. Non-destructive techniques such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened up new fields of application, such as the investigation of freight containers. Muon imaging also has the potential to fill some of the gaps currently existing in concrete NDT. As a first step towards practical use and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. The data acquisition takes more time and signals contain more noise, but the images allowed to detect the same important features that are visible in conventional high energy X-ray tomography. In our experiment, we have shown that muon imaging has potential for concrete inspection. The next steps include the development of mobile detectors and optimising acquisition and imaging parameters. KW - Concrete KW - Muon KW - Radar KW - Ultrasound KW - X-ray PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529974 DO - https://doi.org/10.1007/s10921-021-00797-3 VL - 40 IS - 3 SP - 1 EP - 14 PB - Springer Nature AN - OPUS4-52997 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weise, Frank A1 - Wiedmann, A. A1 - Voland, Katja A1 - Kotan, E. A1 - Ehrig, Karsten A1 - Müller, Harald S. T1 - Auswirkungen von Ermüdungsbeanspruchungen auf Struktur und Eigenschaften von Fahrbahndeckenbeton N2 - Ausgehend von der Zielsetzung der DFG-Forschergruppe 1498, die Einflüsse auf den AKR-Schädigungsprozess in Fahrbahndecken aus Beton grundlegend zu klären, sind zwei aufeinander aufbauende Untersuchungsschwerpunkte Gegenstand dieses Beitrags. Im ersten Schwerpunkt wurden die prüftechnischen Voraussetzungen für die Charakterisierung der Degradation und damit der Rissbildung im Fahrbahndeckenbeton durch die Vorschädigung infolge von Ermüdungsbeanspruchungen geschaffen. Realisiert wurde dies durch die Implementierung und Optimierung eines Monitoringsystems im zyklischen 4-Punkt-Biegeversuch zur simultanen Erfassung der Rissbildung im großformatigen Schwingbalken. Zusätzlich wurde die Röntgen-3D-Computertomografie für die hochauflösende räumliche quantitative Rissanalyse in den Bohrkernen aus den Schwingbalken ohne und mit Vorschädigung weiterentwickelt. Im zweiten Untersuchungsschwerpunkt wurde mittels vielfältiger Experimente an kleinformatigen Probekörpern aus dem Schwingbalken gezeigt, dass durch die Ermüdungsbeanspruchung die bruchmechanischen Materialkennwerte des Betons zum Teil eine signifikante Veränderung erfahren. Based on the objective of the DFG (German research foundation) funded research group 1498 to clarify the influences on the ASR damage process, this paper deals with two focuses of investigation. In the first focus the technical requirements for the characterisation concerning the degradation and the formation of cracks in concrete pavements by the pre-damage as a result of fatigue loading were created. This was realized by the implementation and the optimisation of a monitoring system in the cyclic four point bending test to capture simultaneously the formation of cracks in the beam under sinusoidal bending load. In addition, the X-ray 3D-computed tomography was enhanced for the high-resolution quantitative spatial crack analysis in the drilling cores extracted of the beam under sinusoidal bending load without and with a pre-damage. Building on the first focus, in the second focus of investigation a significant change of the fracture-mechanical properties of the concrete as a result of fatigue loading has been demonstrated in numerous experiments using small specimens extracted from the beam under sinusoidal bending load. KW - Beton KW - CT KW - ROI KW - Risserkennung PY - 2015 DO - https://doi.org/10.1002/best.201400096 SN - 0005-9900 SN - 1437-1006 VL - 110 IS - 1 SP - 22 EP - 33 PB - Ernst CY - Berlin AN - OPUS4-32517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Rieffel, Y. A1 - Ruedrich, J. A1 - Plagge, R. A1 - Weise, Frank A1 - Siegesmund, S. A1 - Ruisinger, U. T1 - An inter-disciplinary model project to develop an innovative winter covering system N2 - Eight monumental sculptural groups made of Carrara marble are situated on the Schlossbrücke in the centre of Berlin in the periphery of the Museum Island, a Unesco world cultural heritage site. T2 - 14es journées d'étude de la SFIIC - Jardin de pierres - Conservation of stone in parks, gardens and cemetries CY - Paris, France DA - 22.06.2011 KW - Marble KW - Cultural heritage KW - Schlossbrücke KW - Protective winter cover KW - Deterioration KW - Numerical simulation PY - 2011 SN - 2-905430-17-6 SP - 122 EP - 131 AN - OPUS4-24368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Urs A1 - Weise, Frank A1 - Grell, S. ED - Fort, R. ED - de Buergo, R. T1 - The long term effects of a water repellent treatment on a volcanic tuff T2 - Heritage, Weathering and Conservation Conference (HWC 2006) CY - Madrid, Spanien DA - 2006-06-21 PY - 2006 SN - 0-415-41272-2 VL - 2 SP - 777 EP - 784 PB - Taylor & Francis CY - London AN - OPUS4-12509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stähler, S. A1 - Niederleithinger, Ernst A1 - Pirskawetz, Stephan A1 - Nowak, Thomas Rudolf A1 - Weise, Frank ED - Sens-Schönfelder, Christoph ED - Ritter, Joachim ED - Wegler, Ulrich ED - Große, Christian T1 - Detection of subtle changes in materials by Coda Wave interferometry T2 - Noise and diffuse wavefields workshop CY - Neustadt an der Weinstraße, Germany DA - 2009-07-05 KW - Coda wave interferometry Beton KW - Schädigung KW - Ultraschall-Transmission PY - 2009 SN - 978-3-00-027952-2 SN - 0947-1944 VL - II SP - 59 EP - 61 AN - OPUS4-20574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Habib, Abdel Karim A1 - Schalau, Bernd A1 - Zeps, Robert A1 - Frank, S. T1 - Vergleich von Modellen zur Simulation einer Lachenverdunstung N2 - Betreiber, deren Betriebsbereiche den erweiterten Pflichten der Störfall-Verordnung unterliegen, müssen einen Sicherheitsbericht anfertigen, in dem Szenarien möglicher Störfälle beschrieben sind. Im Rahmen dieser Störfallauswirkungsbetrachtungen sind auch oftmals Szenarien zu untersuchen, bei denen Flüssigkeiten freigesetzt werden. Der Verdunstungsmassenstrom aus der Flüssigkeitslache ist der maßgebliche Eingangsparameter für die Gasausbreitungsberechnung mit der die Gefährdungsradien ermittelt werden. Für die Berechnung des Verdunstungsmassenstroms werden meist empirische Modelle eingesetzt. Anhand von experimentellen Daten aus eigenen Freilandversuchen werden die Leistungsfähigkeit sowie die Grenzen des Anwendungsbereichs diverser bekannter Modelle untersucht. KW - Verdunstung KW - Empirische Modelle KW - Experimentelle Daten PY - 2010 SN - 1434-9728 SN - 1436-4948 SN - 0372-2457 SN - 0376-1185 VL - 51 IS - 1/2 SP - 22 EP - 27 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-20873 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Apitz, S. A1 - Pistol, Klaus A1 - Weise, Frank A1 - Berger, J. T1 - Untersuchung des Zwängungsverhaltens von selbstverdichtendem Beton bei instationärer Hochtemperaturbeanspruchung bis 750 °C N2 - Bei einer Erwärmung von dehnungsbehinderten Bauteilen entstehen Zwangsspannungen. Im Rahmen einer Masterarbeit in Zusammenarbeit mit der -Bundesanstalt für Materialforschung und -prüfung (BAM) wurde das Zwängungsverhalten von selbstverdichtendem Beton untersucht. Hierzu wurden zylindrische Probekörper im thermomechanischen Prüfstand der BAM bis 7S0 °C erwärmt und bei Konstanthaltung der Dehnung. die Zwangsspannungen gemessen. Neben einem charakteristischen Zwängungsverlauf für den untersuchten SVB konnten deutliche Einflüsse des zur Herstellung verwendeten Kalksteinmehls sowie von Polypropylenfasern auf das Zwängungsverhalten ausgemacht werden. N2 - The heating of bullding stuctures made of concrete causes restraint stress. Furthermore there are only a few investigations known concerning the high temperatute behaviour of SCC. The aim of thestudy was to estimate the development of restraint stress in order to explore the behaviour of SCC in the case of fite. Therefore the special thermomechanical test device of the Federal Institute for Materials Research and Testing (BAM) was used. The investigated SCC showed a characteristic behaviour at high temperatures. In Addition to that, a significant influence of the used limestone Powder and polypropylene fibres were found. KW - Zwangsspannung KW - Selbstverdichtender Beton (SVB) KW - Hochtemperaturverhalten KW - Polypropylenfasern (PPF) PY - 2012 SN - 978-3-8440-1196-8 VL - 3 SP - 83 EP - 93 PB - Shaker AN - OPUS4-26564 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mantouvalou, I. A1 - Bauer, L.J. A1 - Truong, V.-B. A1 - Wagener, Y. A1 - Förste, F. A1 - Maruchenko, O. A1 - Werner, S. A1 - Lizzi, F. A1 - Wieder, Frank A1 - Wolff, T. A1 - Kanngießer, B. A1 - Zaslansky, P. T1 - Quantitative micro-XRF combined with X-ray imaging reveals correlations between Zn concentration and dentin tubule porosity across entire teeth N2 - Bony materials are biogenic composites of protein fibers and mineral that create hierarchical structures. In the case of teeth, dentin is the main component and similar to other bones, it contains porosity at multiple length scales. It is traversed by micron-sized hollow channels known as dentinal tubules, essential for temperature and pain sensation. Tubule density and thus porosity vary throughout the macroscopic three-dimensional (3D) structure, with porosity increasing toward the pulp. The different densities in teeth are easily revealed non-destructively in 3D by X-ray imaging using computer tomography (CT). Yet elemental composition analysis is more difficult to obtain from within the centimeter-sized heterogeneous bulk material. We describe an approach of merging CT measurements of healthy, intact bovine teeth with micro-X-ray fluorescence (micro-XRF) images of matching serially sectioned slices. Through the combination of multi-resolution quantitative CT measurements with elemental mass fraction derivation, gradients in density and element distributions such as calcium (Ca), phosphorus (P), and zinc (Zn) are revealed across entire teeth in 3D. While the main constituents (Ca and P) are homogeneously distributed in the matrix, Zn concentration increases significantly and exponentially toward the pulp. We find an inverse association between dentin tissue density and Zn concentration localizing this element in or around tubules. Our data serve as a quantitative reference for density and Zn mass fractions in healthy, neither carious nor hypermineralized dentin, as a basis for comparisons across species in health and disease states. KW - Dentin density KW - Micro-computer tomography KW - Quantitative micro-X-ray fluorescence KW - Tubule porosity KW - Zn distribution PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654215 DO - https://doi.org/10.1002/VIW.20250173 SN - 2688-3988 SN - 2688-268X SP - 1 EP - 14 PB - Wiley Online Library AN - OPUS4-65421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Adam, Louisa A1 - Villalobos, S. A1 - Guimaraes, M. A1 - Wiggenhauser, Herbert T1 - Detection of cracks perpendicular to the surface using acoustic methods N2 - Cracks perpendicular to the surface may be initial indicators for a deterioration process of concrete structures. Moisture penetrates inside the structure and transports adverse chemicals. The paper presents an investigation about the reliability of available commercial non-destructive evaluation techniques to reliably estimate the depth of surface-breaking cracks in reinforced concrete structures. Aim of the study was the investigation of surface-braking cracks under laboratory conditions. Commercial acoustic devices as impact echo equipment, single ultrasonic transducers and arrays were applied even if they have not been developed for this purpose. The commercial software and descriptions for application was followed strictly to compare the function, precision and repeatability of the measurements. Both, perpendicular notches and cracks have been considered. The study was completed with a discussion about reference specimens. The study was the basis for formulation of gaps in research. The Electric Power Research Institute (EPRI) has initiated and funded a Project. T2 - NDT-CE 2015 - International symposium non-destructive testing in civil engineering CY - Berlin, Germany DA - 15.09.2015 KW - Acoustic test KW - Commercial acoustic devices KW - Ultrasonic test KW - Crack depth KW - Concrete specimens PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-345729 UR - https://www.ndt.net/?id=18412 SN - 1435-4934 VL - 20 IS - 11 SP - 1 EP - 9 PB - NDT.net CY - Kirchwald AN - OPUS4-34572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Procop, Mathias A1 - Radtke, Martin A1 - Krumrey, M. A1 - Hasche, K. A1 - Schädlich, S. A1 - Frank, W. T1 - Electron probe microanalysis (EPMA) measurement of thin-film thickness in the nanometre range N2 - The thickness of thin films of platinum and nickel on fused silica and silicon substrates has been determined by EPMA using the commercial software STRATAGEM for calculation of film thickness. Film thickness ranged in the order 10 nm. An attempt was made to estimate the confidence range of the method by comparison with results from other methods of analysis. The data show that in addition to the uncertainty of the spectral intensity measurement and the complicated fitting routine, systematic deviation caused by the underlying model should be added. The scattering in the results from other methods does not enable specification of a range of uncertainty, but deviations from the real thickness are estimated to be less than 20%. KW - Electron probe microanalysis KW - EPMA KW - Thin films KW - Thickness measurement KW - X-rays PY - 2002 DO - https://doi.org/10.1007/s00216-002-1514-5 SN - 1618-2642 SN - 1618-2650 VL - 374 SP - 631 EP - 634 PB - Springer CY - Berlin AN - OPUS4-7090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marchant, H. K. A1 - Tegetmeyer, H. E. A1 - Ahmerkamp, S. A1 - Holtappels, M. A1 - Lavik, G. A1 - Graf, J. A1 - Schreiber, Frank A1 - Mussmann, M. A1 - Strous, M. A1 - Kuypers, M. M. M. T1 - Metabolic specialization of denitrifiers in permeable sediments controls N2O emissions N2 - Coastal oceans receive large amounts of anthropogenic fixed nitrogen (N), most of which is denitrified in the sediment before reaching the open ocean. Sandy sediments, which are common in coastal regions, seem to play an important role in catalysing this N‐loss. Permeable sediments are characterized by advective porewater transport, which supplies high fluxes of organic matter into the sediment, but also leads to fluctuations in oxygen and nitrate concentrations. Little is known about how the denitrifying communities in these sediments are adapted to such fluctuations. Our combined results indicate that denitrification in eutrophied sandy sediments from the world's largest tidal flat system, the Wadden Sea, is carried out by different groups of microorganisms. This segregation leads to the formation of N2O which is advectively transported to the overlying waters and thereby emitted to the atmosphere. At the same time, the production of N2O within the sediment supports a subset of Flavobacteriia which appear to be specialized on N2O reduction. If the mechanisms shown here are active in other coastal zones, then denitrification in eutrophied sandy sediments may substantially contribute to current marine N2O emissions. KW - Nitrous oxide KW - Denitrification KW - Cross-feeding PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-463061 UR - https://onlinelibrary.wiley.com/doi/full/10.1111/1462-2920.14385 DO - https://doi.org/10.1111/1462-2920.14385 SN - 1462-2920 SN - 1462-2912 VL - 20 IS - 12 SP - 4486 EP - 4502 PB - John Wiley & Sons Ltd AN - OPUS4-46306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Braetz, S. A1 - Nordholt, Niclas A1 - Nerlich, A. A1 - Schreiber, Frank A1 - Tedin, K. A1 - Fulde, M. T1 - TisB enables antibiotic tolerance in Salmonella by preventing prophage induction through ATP depletion N2 - Antibiotic persistence comprises drug-tolerant bacteria that can survive treatment with antibacterial agents, despite lacking classical genetic resistance mechanisms. Therefore, persisters are clinically relevant because they can lead to treatment failures and chronic infections. Additionally, antibiotic persistence facilitates the evolution of resistance through genetic mutations. Persisters are triggered by a lack of nutrients, bacterial toxins, low ATP levels, or other stress responses that shut down bacterial metabolism. However, the involvement of prophages, viruses that integrate into bacterial chromosomes, is less well understood. In this study, we tested a tisAB deletion in Salmonella Typhimurium and examined persister cell formation following treatment with the DNA-damaging drug ciprofloxacin. TisB is a bacterial toxin that increases the influx of protons across the inner bacterial membrane into the cytosol, causing ATP depletion. We demonstrate that the deletion of tisAB increases prophage induction and bacterial killing, leading to a reduced persister cell fraction. The tisAB mutant is unable to down regulate its ATP concentration after exposure to ciprofloxacin, which in turn allows for stronger binding of RecA to single-stranded DNA, the activator of both the SOS response and prophage induction. KW - Antimicrobial resistance KW - Bacterial survival mechanisms KW - Escherichia coli KW - Salmonella typhimurium PY - 2025 DO - https://doi.org/10.1371/journal.ppat.1013498 IS - 9 SP - 1 EP - 23 AN - OPUS4-64642 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Valentin, Jules D. P. A1 - Altenried, Stefanie A1 - Varadarajan, Adithi R. A1 - Ahrens, Christian H. A1 - Schreiber, Frank A1 - Webb, Jeremy S. A1 - van der Mei, Henny C. A1 - Ren, Qun T1 - Identification of Potential Antimicrobial Targets of Pseudomonas aeruginosa Biofilms through a Novel Screening Approach N2 - Pseudomonas aeruginosa is an opportunistic pathogen of considerable medical importance, owing to its pronounced antibiotic tolerance and association with cystic fibrosis and other life-threatening diseases. The aim of this study was to highlight the genes responsible for P. aeruginosa biofilm tolerance to antibiotics and thereby identify potential new targets for the development of drugs against biofilm-related infections. By developing a novel screening approach and utilizing a public P. aeruginosa transposon insertion library, several biofilm-relevant genes were identified. The Pf phage gene (PA0720) and flagellin gene (fliC) conferred biofilm-specific tolerance to gentamicin. Compared with the reference biofilms, the biofilms formed by PA0720 and fliC mutants were completely eliminated with a 4-fold-lower gentamicin concentration. Furthermore, the mreC, pprB, coxC, and PA3785 genes were demonstrated to play major roles in enhancing biofilm tolerance to gentamicin. The analysis of biofilm-relevant genes performed in this study provides important novel insights into the understanding of P. aeruginosa antibiotic tolerance, which will facilitate the detection of antibiotic resistance and the development of antibiofilm strategies against P. aeruginosa. KW - Antimicrobial resistance KW - Bacteria KW - Biofilms KW - Pseudomonas aeruginosa PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-570205 DO - https://doi.org/10.1128/spectrum.03099-22 SP - 1 EP - 5 PB - ASM Journals AN - OPUS4-57020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schreiber, Frank A1 - Zimmermann, M. A1 - Escrig, S. A1 - Lavik, G. A1 - Kuypers, M.M.M. A1 - Meibom, A. A1 - Ackermann, M. T1 - Substrate and electron donor limitation induce phenotypic heterogeneity in different metabolic activities in a green sulphur bacterium N2 - Populations of genetically identical cells can display marked variation in phenotypic traits; such variation is termed phenotypic heterogeneity. Here, we investigate the effect of substrate and electron donor limitation on phenotypic heterogeneity in N2 and CO2 fixation in the green sulphur bacterium Chlorobium phaeobacteroides. We grew populations in chemostats and batch cultures and used stable isotope labelling combined with nanometer‐scale secondary ion mass spectrometry (NanoSIMS) to quantify phenotypic heterogeneity. Experiments in H2S (i.e. electron donor) limited chemostats show that varying levels of NH4+ limitation induce heterogeneity in N2 fixation. Comparison of phenotypic heterogeneity between chemostats and batch (unlimited for H2S) populations indicates that electron donor limitation drives heterogeneity in N2 and CO2 fixation. Our results demonstrate that phenotypic heterogeneity in a certain metabolic activity can be driven by different modes of limitation and that heterogeneity can emerge in different metabolic processes upon the same mode of limitation. In conclusion, our data suggest that limitation is a general driver of phenotypic heterogeneity in microbial populations. KW - NanoSIMS KW - Phenotypic heterogeneity PY - 2018 UR - https://onlinelibrary.wiley.com/doi/abs/10.1111/1758-2229.12616 DO - https://doi.org/10.1111/1758-2229.12616 SN - 1758-2229 VL - 10 IS - 2 SP - 179 EP - 183 PB - John Wiley & Sons Ltd AN - OPUS4-44596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Block, S. A1 - Boß, K.-H. A1 - Frobese, D.-H. A1 - Pape, H. A1 - Gösslinghoff, L. A1 - Grossepieper, T. A1 - Kasper, R. A1 - Kirchner, W. A1 - Kollmann, P. A1 - Kröger, P. A1 - Ringlstetter, P. A1 - Kuska, T. A1 - Mattejat, K. A1 - Niehüser, H. A1 - Pfeiffer, F. A1 - Pötzsch, Klaus-Michael A1 - Jochems, Frank A1 - Schäfer, H. A1 - Vogt, W. A1 - Zankl, C. A1 - Ludzay, J. T1 - Empfehlungen zur Vermeidung von Überdrücken an Tankfahrzeugen bei Untenbefüllung N2 - Das Risiko von Überdrücken bei der Untenbefüllung von Tankfahrzeugen hat zu Vorfällen mit zum Teil erheblichen Sach- und Personenschäden geführt und ist ein nicht auszuschließendes Gefährdungspotential für Menschen, Umwelt, Anlagen und Transportmittel. Zur weiteren Verbesserung des Managements dieses Risikos und seiner potentiellen Auswirkungen hat der MWV die DGMK gebeten, das Thema in einem Projekt zu bearbeiten, um mögliche Sicherungsdefizite aufzudecken und Lösungsmöglichkeiten aufzuzeigen. Als Forschungsstelle wurde die Physikalisch-Technische Bundesanstalt (PTB) ausgewählt, die das DGMK-Projekt 727 „Überdrucksicherung an Tankfahrzeugen“ gemeinsam mit Vertretern von Tankfahrzeug- und Armaturenherstellern, Mineralölindustrie sowie der Bundesanstalt für Materialforschung und -prüfung (BAM) bearbeitet hat. In Messungen an zwei Füllstellen wurden reale Druck-, Temperatur- und Volumenstromverhältnisse für die Beladung eines Tankfahrzeugs aufgenommen. Es wurde festgestellt, dass es in einem Tankfahrzeug, in dem keine zusätzlichen Druckverluste wie z. B. durch Vereisungen im Inneren der Kippventil-Flammendurchschlagsicherungs-Armatur auftreten, zu keinem unzulässig hohen Druckaufbau in einer Tankwagenkammer kommen kann. Zusätzlich erfolgten Versuche in einer Kältekammer, um die Möglichkeit und die Randbedingungen einer Vereisung des Kippventils und der Flammendurchschlagsicherung zu ermitteln. Mit diesen Ergebnissen sind Szenarien erarbeitet worden, die bekannte Überdruckschadensereignisse erklären können. Aus einer Gefährdungsbeurteilung heraus wurden Maßnahmen beschrieben, wie zukünftig solche Überdruckschäden an Tankfahrzeugen vermieden werden können. Aufbauend auf den Ergebnissen des Projektes hat die Projektbegleitung diese und weitere Maßnahmen hinsichtlich ihrer Umsetzbarkeit diskutiert und die vorliegende Empfehlung zur Vermeidung von Überdrücken an Tankfahrzeugen bei Untenbefüllung erarbeitet. KW - Untenbefüllung KW - Tankfahrzeuge KW - Überdruck KW - Mineralöl KW - Sicherheitsventile PY - 2012 VL - 727 IS - 3 SP - 1-4 EP - Anl. 1-3 AN - OPUS4-27921 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bauer, L.J. A1 - Wieder, Frank A1 - Truong, V. A1 - Förste, F. A1 - Wagener, Y. A1 - Jonas, A. A1 - Praetz, S: A1 - Schlesiger, C. A1 - Kupsch, Andreas A1 - Müller, Bernd R. A1 - Kanngießer, B. A1 - Zaslansky, P. A1 - Mantouvalou, I. T1 - Absorption Correction for 3D Elemental Distributions of Dental Composite Materials Using Laboratory Confocal Micro-X-ray Fluorescence Spectroscopy N2 - Confocal micro-X-ray fluorescence (micro-XRF) spectroscopy facilitates three-dimensional (3D) elemental imaging of heterogeneous samples in the micrometer range. Laboratory setups using X-ray tube excitation render the method accessible for diverse research fields but interpretation of results and quantification remain challenging. The attenuation of X-rays in composites depends on the photon energy as well as on the composition and density of the material. For confocal micro-XRF, attenuation severely impacts elemental distribution information, as the signal from deeper layers is distorted by superficial layers. Absorption correction and quantification of fluorescence measurements in heterogeneous composite samples have so far not been reported. Here, an absorption correction approach for confocal micro-XRF combining density information from microcomputed tomography (micro-CT) data with laboratory X-ray absorption spectroscopy (XAS) and synchrotron transmission measurements is presented. The energy dependency of the probing volume is considered during the correction. The methodology is demonstrated on a model composite sample consisting of a bovine tooth with a clinically used restoration material. KW - Micro X-ray fluorescence spectroscopy KW - Dental composite materials KW - Computed tomography KW - Absorption correction PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601630 DO - https://doi.org/10.1021/acs.analchem.4c00116 SN - 0003-2700 SN - 1520-6882 VL - 96 IS - 21 SP - 8441 EP - 8449 PB - American Chemical Society Publications CY - Washington, DC AN - OPUS4-60163 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -