TY - CONF A1 - Feistkorn, S. A1 - Algernon, D. A1 - Arndt, R. A1 - Ebell, Gino A1 - Friese, M. A1 - Grosse, C. U. A1 - Holstein, R. A1 - Niederleithinger, Ernst A1 - Schickert, M. A1 - Schulze, S. A1 - Taffe, A. A1 - Walther, A. A1 - Wolf, J. A1 - Zoega, A. A1 - Zwanzig, M. T1 - Introduction to DIN 4871: Qualification of NDT Personnel in Civil Engineering (NDT-CE) N2 - Recently, non-destructive testing in civil engineering (NDT-CE), in particular of concrete components, has successfully mastered the leap from research to practice. Several methods have been established for field inspections to determine the concrete cover of reinforcement or to estimate the compressive strength as well as other parameters related to the concrete material. In addition, the application of nondestructive testing is indispensable, if information about the inner structure - such as the location of rebars and tendon ducts or the damage-related condition assessment to detect grouting defects, honeycombs, delamination, or corrosion - is required. Besides the selection of a suitable NDT method and an appropriate inspection system, the reliability of the results depends largely on the person who applies the non-destructive inspection technique and evaluates the inspection results. To ensure a high quality of non-destructive concrete evaluation as well as to keep the uncertainty caused by the inspection personnel to a minimum, structured, consistent and regulated theoretical as well as practical training of inspection personnel is essential. To close this gap, the subcommittee of education (UA-A) within the committee for NDT-CE of the German Society for Nondestructive Testing (DGZfP) has been reactivated in 2018 to establish uniform training standards for nondestructive concrete inspections in the long term. The subcommittee consists of scientists, practitioners, authorities, and clients. So far, the national standard DIN 4871 “Non-destructive testing - Qualification and Certification of NDT personnel in Civil Engineering (NDT-CE)” was developed and is currently under review. This standard considers the civil-industry-specifics, for example, that standards for NDT of concrete, as well as related product standards with a few exceptions, still do not exist at the moment. Within this presentation, the concept, the connection to ISO 9712 and other standards as well as an overview of the developed German standard DIN 4871 will be presented. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Non-destrucive testing KW - Civil engineering PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-555250 UR - https://www.ndt.net/article/ndtce2022/paper/66594_manuscript.pdf VL - 2022/09 SP - 1 EP - 12 PB - NDT.net CY - Bad Breisig AN - OPUS4-55525 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Arndt, R.W. A1 - Grosse, C.U, A1 - Maehner, D. A1 - Niederleithinger, Ernst A1 - Taffe, A. A1 - Algernon, D. A1 - Berger, J. A1 - Kessler, S. A1 - Krueger, M. A1 - Kruschwitz, Sabine A1 - Ufermann-Wallmeier, D. A1 - Walther, A. T1 - Non-destructive testing in civil engineering: A memorandum for teaching at German-speaking universities N2 - This contribution summarizes actual developments and draft fundamental teaching topics in the field of nondestructive testing in civil engineering (NDT-CE). It is based on the first memorandum on teaching and research in the field of NDT-CE at German speaking universities and provides an overview of the academic education and highlights possible focuses, especially in teaching but also takes into account noteworthy developments and topics in research in the field of NDT-CE. Suggestions are given for the development and advancement of the teaching curricula in regards to a comprehensive and sound professional education of students in civil engineering and adjacent disciplines. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Curriculum KW - NDT-CE KW - University KW - Competencies PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-563269 UR - https://www.ndt.net/article/ndtce2022/paper/61547_manuscript.pdf SP - 1 EP - 10 PB - NDT.net AN - OPUS4-56326 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, T. A1 - Murtuz, A. K. M. G. A1 - Hafiz, A. A1 - Dusicka, P. A1 - Niederleithinger, Ernst ED - Gabrijel, I. ED - Grosse, C. ED - Skazlić, M. T1 - Post-earthquake damage evaluation of concrete structures using ultrasonic monitoring: A proof-of concept laboratory study N2 - In earthquake-prone regions such as the Pacific Northwest, damage assessment tools are needed to enable safety evaluations to support recovery. Currently, damage assessment is performed primarily by visual inspection and is often impossible for structural members that are inaccessible, such as deep foundations or interior members hidden by cladding. This study explores the possibility of using embedded ultrasonic transducers to monitor reinforced concrete members for damage progression under earthquake loading. A novel methodology is proposed where changes in the member condition due to an increase in the earthquake-type loading of a full-scale column-foundation specimen are correlated with changes in the recorded ultrasonic waveforms. The discussed preliminary analysis of the ultrasonic signals is based on wave propagation velocity, changes in the coda wave portion, and maximum amplitude of the signals. Three embedded transducers were used to continuously monitor the laboratory specimen during destructive testing. This paper provides an overview of the proposed methodology, outlines the laboratory experiment, and discusses some preliminary observations. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.3.2019 KW - Concrete KW - Monitoring KW - Ultrasound KW - earthquake PY - 2019 SN - 978-2-35158-227-5 DO - https://doi.org/10.1007/978-3-031-07258-1_84 SP - 112 EP - 119 PB - RILEM Publications S.A.R.L. CY - Paris, France AN - OPUS4-47679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Algernon, D. A1 - Arndt, R.W. A1 - Denzel, W. A1 - Ebsen, B. A1 - Feistkorn, S. A1 - Friese, M. A1 - Große, C.U. A1 - Kathage, S. A1 - Keßler, S. A1 - Köpp, Christian A1 - Küttenbaum, Stefan A1 - Lohse, C. A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Schickert, M. A1 - Schröder, G. A1 - Taffe, A. A1 - Timofeev, Juri A1 - Walther, A. A1 - Wilcke, M. A1 - Wolf, J. A1 - Wöstmann, Jens T1 - Test specimen concepts in regard to quality assurance and validation of nondestructive testing in civil engineering N2 - The process of ensuring reliability of NDT applications contains various aspects, such as determining the performance and probability of success, the uncertainty in measurement, the provision of clear and functional procedures and ensuring the correct application accordingly. Test specimens have become powerful elements in supporting many of these aspects. Within the committee for NDT in Civil Engineering (NDT-CE) of the German Society for Nondestructive Testing (DGZfP), the subcommittee on Quality Assurance (UA-QS) therefore addresses the design and the integration of test specimens in the quality assurance process. Depending on the specific purpose, the requirements on test specimens can vary significantly based on the defined simulated scenario. The most prominent purposes of test specimens might be seen in providing references for inspection systems in regard to function control, calibration and validation. Further aspects can be parametric studies, basic investigation of physical principles related to NDT or a simplified and therefore comprehensive demonstration of inspection concepts (e.g. for teaching purposes). The specific purpose of a test specimen dictates the requirements regarding its conception, including the exact design, the material or the fabrication accuracy and the conditioning. In the development of a general guideline by the UA-QS for application-specific procedures and their validation, the use of test specimens is addressed and specific concepts for the design of test specimens are made. This includes the analysis of the measurement process regarding any given application, deriving an adequate calibration approach for it and designing test specimens (calibration specimens) accordingly. Furthermore, it includes the validation of the procedure taking into account all conditions related to the specific application in the field. The validation requires a statistically sufficient number of trials. Thorough evaluation of each trial can only be established if the ground-truth is known. Therefore, test specimens providing a realistic but controlled simulation of the inspection problem are valuable and indispensable elements in the validation process. The requirement of being fully realistic will often not be possible to fulfill due to practical restrictions. Any aspect that cannot be included in the simulation realistically needs to be simulated conservatively. This again, requires a sufficient understanding of the inspection principle and technique to ensure conservativeness. Among other quality-assurance-related aspects, the UA-QS establishes concepts and guidelines regarding sound and efficient approaches for the specific purposes of test specimens. This subcommittee brings together representatives of different Groups along the entire value chain of NDT-CE, including researchers, practitioners, manufacturers and clients. They all work together in establishing a common understanding and level of quality assurance in the industry. T2 - SMT and NDT-CE 2018 CY - New Brunswick, NJ, USA DA - 27.08.2018 KW - Quality assurance KW - Procedure KW - Reliability KW - Validation KW - Reference specimen PY - 2019 UR - https://asnt.org/smt18papers SN - 978-1-57117-456-7 VL - 11/19 SP - 39 EP - 48 PB - The American Society for Nondestructive Testing, Inc. CY - Columbus, OH, USA AN - OPUS4-47240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Algernon, D. A1 - Arndt, R.W. A1 - Denzel, W. A1 - Ebsen, B. A1 - Feistkorn, S. A1 - Friese, M. A1 - Große, C.U. A1 - Kathage, S. A1 - Keßler, S. A1 - Köpp, Christian A1 - Küttenbaum, Stefan A1 - Lohse, C. A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Schickert, M. A1 - Schröder, G. A1 - Taffe, A. A1 - Timofeev, Juri A1 - Walther, A. A1 - Wilcke, M. A1 - Wolf, J. A1 - Wöstmann, Jens T1 - NDT procedures in relation to quality assurance and validation of nondestructive testing in civil engineering N2 - The field of non-destructive testing of civil structures (NDT-CE) has been continuously growing. Due to the complexity and diversity of civil constructions as well as the heterogeneity of concrete, specific standards or guidelines for the application of modern NDT-CE are still missing. The development of individual solutions is the current approach, which is just as challenging as it is common for NDT-CE. With the increasing development and commercialization of NDT-CE technology, the group of practitioners is growing. To ensure a good level of quality in the industry, it appears necessary to establish adequate means. Naturally, the performance of NDT-CE methods regarding a specific application is strongly dependent on choosing the most suitable inspection technique and applying it correctly, generally referred to as the inspection procedure in the field of NDT. There are well-defined guidelines regarding procedure documentation and handling in many fields of NDT (e.g. nuclear, aerospace or automotive) according to the high importance of procedures in assuring a successful and reliable application. For a long time, this has not always been the case with NDT-CE, which is still considered a unique discipline of NDT. Part of the reason for that might be the young development state of NDTCE, the heterogeneity of building materials like concrete, timber or masonry as a material and the diversity of civil structures. In consequence, NDT-CE procedure development is considered challenging. Among other aspects, addressed in the subcommittee on Quality Assurance (UA-QS) within the committee for NDT-CE of the German Society for Nondestructive Testing (DGZfP), part of its work aims at establishing an adequate basis for NDT-CE procedure development. While some of the highly developed approaches from other industries are taken into consideration, they need to be analyzed regarding their suitability for NDT-CE and adapted accordingly. For a procedure to be as defined as possible, it needs to contain sufficient information, such as the scope and limitations regarding material, geometry and condition of the test object, inspection parameters, calibration, data acquisition, analysis criteria as well as requirements regarding the inspection personnel. For a successful implementation in the field, it is important to define the specific procedure as precisely as possible. Despite the necessity of a great amount of information to be included, the procedure needs to be suitable for efficient field application. The UA-QS is developing a guideline for NDT-CE procedures suitable for application in this field of NDT to ensure correct and reproducible application. To demonstrate and evaluate this concept, specific examples of procedures are also produced. In particular, the UA-QS has developed a procedure for the detection and positioning of tendon ducts using Ground Penetrating Radar (GPR). This procedure is tested regarding the practical applicability in a roundrobin on a defined type of reference test block. T2 - SMT and NDT-CE 2018 CY - New Brunswick, NJ, USA DA - 27.08.2018 KW - Quality assurance KW - Procedure KW - Reliability KW - Validation KW - Reference specimen PY - 2019 UR - https://asnt.org/smt18papers SN - 978-1-57117-456-7 VL - 11/19 SP - 31 EP - 38 PB - The American Society for Nondestructive Testing, Inc. CY - Columbus, OH, USA AN - OPUS4-47239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abraham, O. A1 - Niederleithinger, Ernst A1 - Chapeleau, X. A1 - Klikowicz, P. A1 - Brühwiler, E. A1 - Bassil, A. A1 - Wang, Xin A1 - Chakraborty, J. A1 - Bayane, I. A1 - Leduc, D. A1 - Salamak, M. A1 - Katunin, A. A1 - Sørensen, J.D. T1 - Addressing the need to monitor concrete fatigue with nondestructive testing: Results of infrastar European project N2 - Fatigue is one of the most prevalent issues, which directly influences the service life expectancy of concrete structures. Fatigue has been investigated for years for steel structures. However, recent findings suggest that concrete structures may also be significantly subjected to fatigue phenomena that could lead to premature failure of certain structural elements. To date, fatigue of reinforced concrete has been given little focus. Knowledge on the influence factors and durability/capacity effects on this material should be improved. Current technological means to measure fatigue in civil structures like bridges and wind turbines (both onshore and offshore) are outdated, imprecise and inappropriate. Meanwhile, this topic has got much more attention as time-variant loading on concrete structures plays an increasing role, e.g. in bridges with increasing traffic and heavier trucks, and for wind turbines for renewable energy production, e.g. for offshore wind turbine support structures affected by wind and waves. The European Innovative Training Networks (ITN) Marie Skłodowska-Curie Actions project INFRASTAR (Innovation and Networking for Fatigue and Reliability Analysis of Structures - Training for Assessment of Risk) provides research training for 12 PhD students. The project aims to improve knowledge for optimizing the design of new structures as well as for more realistic verification of structural safety and more accurate prediction of the remaining fatigue lifetime of existing concrete structures. First, the INFRASTAR research framework is detailed. Then it will be exemplified through the presentation of the major results of the four PhD students involved in the work package dealing with auscultation and monitoring. This includes the development and improvement of Fiber Optics (FO) and Coda Wave Interferometry (CWI) for crack sizing and imagery, new sensor technologies and integration, information management, monitoring strategy for fatigue damage investigation and lifetime prediction. T2 - SMT and NDT-CE 2018 CY - New Brunswick, NJ, USA DA - 27.08.2018 KW - Concrete KW - Fatigue KW - Crack KW - Monitoring KW - Non-destructive testing PY - 2019 UR - https://asnt.org/smt18papers SN - 978-1-57117-456-7 VL - 11/19 SP - 2 EP - 13 PB - The American Society for Nondestructive Testing, Inc. CY - Columbus, OH, USA AN - OPUS4-47237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bearce, R.G. A1 - Mooney, M.A. A1 - Niederleithinger, Ernst A1 - Revil, A. T1 - Characterization of simulated soilcrete column curing using acoustic tomography N2 - Implementation of soilcrete columns via jet grouting or deep soil mixing to stabilize problematic subsurface soils is common in underground construction. However, industry is faced with limited options to characterize column geometry and quality of the resulting soilcrete without excavation or destructive testing. Laboratory-scale experiments were conducted on simulated soilcrete columns using crosshole ultrasonic testing to evaluate the feasibility of acoustic tomography to characterize soilcrete geometry and quality. Data were acquired on multiple columns immediately after placement up to a curing time of 120 hours. Jet grout compressional wave velocity (VP) was estimated using a first arrival time approach and inverted to construct acoustic tomograms. Acoustic tomograms indicate that crosshole ultrasonic testing is able to characterize the changes in acoustic properties that result from jet-grout curing, locate contrasts between weaker/stronger regions in the jet grout, and estimate geometry of the column. T2 - Geo-congress 2014 CY - Atlanta, Georgia, USA DA - 23.02.2014 KW - Jet grouting KW - Ultrasound KW - Tomography KW - Ray tracing KW - Simulation PY - 2014 SN - 978-0-7844-1327-2 DO - https://doi.org/10.1061/9780784413272.044 N1 - Serientitel: Geotechnical Special Publication (GSP) – Series title: Geotechnical Special Publication (GSP) VL - 234 SP - 465 EP - 474 AN - OPUS4-32601 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Goldschmidt, Sebastian A1 - Niederleithinger, Ernst A1 - Bienert, K. A1 - Schalk, H. A1 - Molkenthin, A. ED - Jacobsen, S. ED - Justnes, H. ED - Cepuritis, R. ED - Hornbostel, K. ED - Peng, Y. T1 - Quality control of hydrophobic coatings with an integrated marker element by laser-induced breakdown spectroscopy (LIBS) N2 - Reinforced concrete structures are affected by damage caused e. g. by freeze-thaw effects or corrosion. Most damage processes are triggered by moisture transport including soluble substances. Hydrophobie coatings can be used for prevention of such damage, but quantitative on-site quality assurance methods are so far missing. A way to overcome this problem is to integrate marker substances into the coating, which can be detected by spectroscopic methods. Different types of marker elements have been tested. It can be shown that transition metals are best suited for the task. Currently a LIBS (laser-induced breakdown spectroscopy) System is developed for the measurement of penetration depth and content of the hydrophobic coating via the marker element in the peripheral zone of concrete. T2 - ICDC 2012 - International congress on durability of concrete CY - Trondheim, Norway DA - 18.06.2012 KW - Hydrophobic coating KW - Marker element KW - Quality control KW - Depth of penetration KW - Concrete repair KW - Pitting corrosion KW - Chloride KW - Exposure KW - Freeze-taw cycles KW - Laser-induced breakdown spectroscopy KW - Hydrophobierung KW - Laser Induced Breakdown Spektroskopie KW - Qualitätskontrolle PY - 2012 SN - 978-82-8208-031-6 SP - Session B 1, 1 EP - 14 AN - OPUS4-27527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bienert, K. A1 - Schalk, H. A1 - Molkenthin, A. A1 - Wilsch, Gerd A1 - Goldschmidt, Sebastian A1 - Niederleithinger, Ernst ED - Grantham, M. ED - Mechtcherine, V. ED - Schneck, U. T1 - Quality control of hydrophobic coatings with an integrated marker element by laser-induced breakdown spectroscopy (LIBS) N2 - Reinforced concrete structures are affected by damage, caused e.g., by freeze-thaw effects or corrosion. Most damage processes are triggered by moisture transport including soluble substances. Hydrophobic coatings can be used for prevention of such damage, but quantitative on-site quality assurance methods are so far missing. A way to overcome this problem is to integrate marker substances into the coating, which can be detected by spectroscopic methods. Different types of marker elements have been tested. It can be shown that transition metals are best suited for the task. Currently a LIBS (Laser Induces Breakdown Spectroscopy) system is developed for the measurement of penetration depth and content of the hydrophobic coating via the marker element in the peripheral zone of concrete. T2 - Concrete solutions 2011 - 4th International conference on concrete repair CY - Dresden, Germany DA - 26.09.2011 KW - Laser induced breakdown spectroscopy (LIBS) KW - Hydrophobic coating KW - Quality control KW - Depth of penetration KW - Concrete repair KW - Chloride PY - 2012 SN - 978-0-415-61-622-5 SP - 805 EP - 811 PB - Taylor & Francis CY - London AN - OPUS4-25151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bienert, K. A1 - Schalk, H. A1 - Molkenthin, A. A1 - Wilsch, Gerd A1 - Goldschmidt, Sebastian A1 - Niederleithinger, Ernst T1 - Qualitätskontrolle von Hydrophobierungen mit einem integrierten Markerelement durch die laser-induced breakdown spectroscopy (LIBS) N2 - Stahlbetonbauwerke sind nutzungsbedingt Umwelteinwirkungen ausgesetzt, die zu Schäden an der Konstruktion führen können. Dabei ist in erster Linie die Einwirkung von tausalzhaltigen Wässern im Winter zu nennen, die durch den Beton kapillär und über Diffusionsvorgänge aufgenommen werden. Dies fuhrt durch den Chlorideinfluss langfristig zur Korrosion der Bewehrung. Zudem leidet die Frost-Taubeständigkeit durch das Herabsetzen der Gefrierpunkttemperatur im Porenwasser. Die Folge sind Abwitterungen an der Betonoberfläche. Die meisten zerstörenden Prozesse werden durch einen Feuchtigkeitstransport ausgelöst, der lösliche Substanzen beinhaltet. Hydrophobierungen können zur Vorbeugung von solchen Schäden verwendet werden aber es gibt bisher keine Methoden zur Qualitätssicherung vor-Ort. Eine Möglichkeit der Qualitätssicherung ist, eine markierende Substanz in, die Tiefenhydrophobierung zu integrieren, die durch spektroskopische Methoden detektiert werden kann. Unterschiedliche Arten von Markerelementen wurden hierfür getestet Es konnte gezeigt werden, dass Übergangsmetalle am besten als Marker geeignet sind. Derzeit wird ein mobiles LIBS - System für die Messung der Eindringtiefe und zu hoch aufgelösten Darstellung der Wirkstoffverteilung in der Betonrandzone entwickelt. T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 12.09.2012 KW - Hydrophobierung KW - Markerelement KW - Qualitätskontrolle KW - Eindringtiefe KW - Betonreparatur KW - Lochfraßkorrosion KW - Chloride KW - Frost-Tausalz-Wechsel KW - LIBS PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-0398 EP - 2-0409 AN - OPUS4-27601 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Clauß, F. A1 - Ahrens, M. A. A1 - Mark, P. ED - Krieger, J. ED - Isecke, B. T1 - Ultraschallbasierte Überwachung von Stahl- und Spannbeton-konstruktionen – erste Ergebnisse der DFG-Forschungsgruppe 2825 CoDA N2 - Die Überwachung von Bauteilen aus Stahl- oder Spannbeton mit Ultraschall hat in Labor- und Technikumsversuchen schon vielversprechende Ergebnisse gezeigt. Besonders gute Resultate wurden dabei mit eingebetteten Ultraschalltrans-ducern und bei Auswertung der Daten mit der hochsensiblen Codawelleninterferometrie erzielt. Erfasst werden können neben Temperatur- und Feuchteeffekten auch Belastungszustände und jegliche Art von Schädigung, die mit Mikro- oder Makrorissbildung einhergeht. Seit 2019 untersucht die DFG-Forschergruppe 2825 „CoDA“ (Sprecher: Prof. Christoph Gehlen, TU München) ver-schiedenste Aspekte dieser innovativen Technologie mit dem Ziel, Einflussgrößen quantitativ zu erfassen, Umweltein-flüsse zu korrigieren und 3D-Auswerteverfahren zu verbessern. Final soll eine am Bauwerk einsatzfähige Methode ent-stehen, die klassische Monitoringverfahren ergänzt und erweitert sowie Input zu einem Update des statischen Systems liefert. Aufgaben der BAM in der Forschergruppe ist neben Verbesserung und Adaptierung der Messsystem und Sensorik auch Langzeitversuche an einem Großobjekt und Testinstallationen an Realbauwerken. Hierzu liegen erste Ergebnisse vor, die zeigen, dass die Technologie auch außerhalb des Labors einsatzfähig ist. T2 - 4. Brückenkolloquium CY - Online meeting DA - 08.09.2020 KW - Brücke KW - Monitoring KW - Ultraschall KW - Codawelleninterferometrie PY - 2020 SN - 978-3-8169-3518-6 SP - 473 EP - 480 PB - expert CY - Tübingen AN - OPUS4-51205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meggyes, Tamás A1 - McDonald, C. A1 - Roehl, K. E. A1 - Witt, K. J. A1 - Debreczeni, Á. A1 - Niederleithinger, Ernst ED - Annokkée, G. J. T1 - Reducing the risk for tailings facilities T2 - 8th International FZK/TNO Conference on Contaminated Soil ; 8th ConSoil 2003 CY - Gent, Belgium DA - 2003-05-12 PY - 2003 SN - 0947-8620 N1 - Serientitel: Wissenschaftliche Berichte / Forschungszentrum Karlsruhe in der Helmholtz-Gemeinschaft – Series title: Wissenschaftliche Berichte / Forschungszentrum Karlsruhe in der Helmholtz-Gemeinschaft IS - 6943 SP - E3239 EP - E3247 PB - Forschungszentrum CY - Karlsruhe AN - OPUS4-2808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Schalk, H. A1 - Bienert, K. A1 - Molkenthin, A. A1 - Goldschmidt, Sebastian A1 - Niederleithinger, Ernst T1 - Quality control of hydrophobic coatings with an integrated marker element by laser-induced breakdown spectroscopy (LIBS) N2 - Reinforced concrete structures are affected by damage, caused e.g., by freeze-thaw effects or corrosion. Most damage processes are triggered by moisture transport including soluble substances. Hydrophobic coatings can be used for prevention of such damage, but quantitative on-site quality assurance methods are so far missing. A way to overcome this problem is to integrate marker substances into the coating, which can be detected by spectroscopic methods. Different types of marker elements have been tested. It can be shown that transition metals are best suited for the task. Currently a LIBS (Laser Induces Breakdown Spectroscopy) system is developed for the measurement of penetration depth and content of the hydrophobic coating via the marker element in the peripheral zone of concrete. T2 - 2nd International conference Micro Durability - Microstructural-related durability of cementitious composites CY - Amsterdam, The Netherlands DA - 11.04.2012 KW - Hydrophobierung KW - Laser Induced Breakdown Spektroskopie (LIBS) KW - Qualitätskontrolle PY - 2012 SN - 978-2-35158-129-2 N1 - Serientitel: RILEM proceedings – Series title: RILEM proceedings VL - PRO83 SP - 1 EP - 10 AN - OPUS4-27534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ernst, A. A1 - Klein, S. A1 - Hall, T. A1 - Ávila Calderón, Luis A1 - Bähre, D. T1 - Electrochemical dressing of hard tools for abrasive precision machining N2 - In this study an approach for dressing metallic bonded honing stones with hard cutting grains on the basis of electrolysis is investigated. By a combination of concepts from electrochemical machining (ECM) and electropolishing a test rig was designed and put into operation. In general, it can be stated that the Approach investigated in this paper has proved to be a suitable dressing method for honing stones. However, the dressing result is highly dependent on bond components, cutting grain size and concentration which lead to local differences in the material removal and irregular topographies. This could be overcome, for example, by setting the dressing parameters more precisely based on the best results presented in this paper. T2 - International Symposium on ElectroChemical Machining Technology CY - Saarbrücken, Germany DA - 14.11.2019 KW - Irregular topography KW - Honing KW - Electrochemical dressing KW - Honing Stone KW - Laser Scanning Microscopy KW - Electropolishing PY - 2019 SN - 978-3-00-064086-5 SP - 96 EP - 108 PB - Fertigungstechnik Saarbrücken CY - Saarbrücken AN - OPUS4-49490 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -