TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo A1 - Baeßler, Matthias T1 - 3D spatial modelling of CPT data for probabilistic preliminary assessment of potential pile tip damage upon collision with boulders N2 - Tip damage of monopiles from boulder collisions during installation has emerged as a critical design issue, primarily due to the combination of the widespread use of large-diameter piles and the complexity of the ground conditions at the available sites. Recently, a framework relating potential pile tip damage to cone tip resistance from Cone Penetration Tests (CPTs) has been proposed in the literature. Gaussian processes are powerful stochastic models that enable probabilistic spatial interpolation of soil data at any location within a site. On this basis, this study utilizes sparse CPT data from a site in the North Sea, to first develop an efficient Gaussian process regression model, which is used to derive a three-dimensional (3D) probabilistic predictive map of the cone tip resistance. Assuming deterministic loading conditions and a factual collision with a boulder of pre-defined properties, the cone tip resistance predictive model is subsequently used for a probabilistic preliminary assessment of potential pile tip damage. Results of the analysis are realistic 3D probability maps of potential damage that aim to support engineering judgment and contribute towards cost-effective site investigation planning and offshore wind farm design. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG 2025) CY - Nantes, France DA - 09.06.2025 KW - CPT data KW - Gaussian process regression KW - Boulder impact KW - Preliminary pile tip damage assessment PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634417 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-323 SP - 505 EP - 510 PB - International Society for Soil Mechanics and Geotechnical Engineering CY - London AN - OPUS4-63441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Balscheit, Hagen A1 - Geißler, Peter A1 - Schepers, Winfried A1 - Cuèllar, Pablo T1 - Evaluation of pile tip buckling based on large scale tests N2 - Der Beitrag beschreibt eine groß angelegte Versuchskampagne mit Pfahlrammungen, um das Risiko des plastischen Versagens der Pfahlspitze besser zu verstehen und numerische Modelle zu validieren. Ein numerisches Modell mit transientem Bodenkontakt zeigt eine gute Übereinstimmung mit den Testergebnissen. Parametervariationen verdeutlichen, wie empfindlich die Pfahlreaktion auf Imperfektionen und Randbedingungen ist. T2 - 5TH INTERNATIONAL SYMPOSIUM ON FRONTIERS IN OFFSHORE GEOTECHNICS CY - Nantes, France DA - 09.06.2025 KW - Pile Tip Buckling KW - Monopile KW - Offshore Windenergy KW - Driving Refusal KW - Large Scale Test PY - 2025 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-476 SP - 1218 EP - 1223 PB - International Society for Soil Mechanics and Geotechnical Engineering (ISSMGE) CY - Nantes AN - OPUS4-63387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - System identification of inverse, multimodal and nonlinear problems using evolutionary computing - Application to a pile structure supported on nonlinear springs N2 - This paper deals with the system identification of a mechanical structure supported by nonlinear springs subjected to an external load. If all mechanical parameters of the system were known, the displacement of the system subjected to this load could be easily calculated. However, the monitoring applications often deal with the inverse problem. The loads and displacements of the system are known and certain mechanical Parameters of the system are sought. The solution of such inverse problems can be difficult, especially when they have a nonlinear and multimodal character, which often makes them appear intractable at first sight. However, evolutionary computing can be applied to solve this inverse, nonlinear and multimodal problem. Sometimes a prior knowledge exists on certain system properties, which is difficult to implement into analytical or numerical solvers. This knowledge can play a decisive role in identifying the System properties and it can be easily included as a boundary condition when applying evolutionary algorithms. This article discusses how and under what conditions the unknown spring resistances can be identified. The practical application of this procedure is exemplified here with the mechanical system of a pile foundation. KW - Evolutionary computing KW - Inverse problem KW - Multimodal solution KW - System identification KW - Pile monitoring PY - 2015 DO - https://doi.org/10.1016/j.engstruct.2015.07.034 SN - 0141-0296 SN - 1873-7323 VL - 101 SP - 609 EP - 620 AN - OPUS4-39310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kullolli, Borana A1 - Stutz, H. H. A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rackwitz, F. ED - Cardoso, A. S. ED - Borges, J. L. ED - Costa, P. A. ED - Gomes, A. T. ED - Marques, J. C. ED - Vieira, C. S. T1 - A generalized plasticity model adapted for shearing interface problems N2 - The response of many geotechnical systems, whose structural behavior depends on shearing effect, is closely related to soil structure interaction phenomenon. Experimentally it is found that the localisation of these effect happens at a narrow soil layer next to the structure. Numerically, this behavior can be modelled through inter-face elements and adequate constitutive models. In this work, a constitutive model in the framework of Gen-eralized Plasticity for sandy soils has been chosen to be adapted for the interface zone. From the direct shear experiments a sandy soil at loose and dense states under different normal pressures is considered. The adapted constitutive model is able to reproduce contraction and dilatation of the soil according to its relative density and it shows a good agreement with the experimental data. T2 - Conference CY - Porto, Portugal DA - 25.06.2018 KW - Numerical modelling KW - Soil-pile interaction KW - Interface KW - Shearing PY - 2018 SN - 978-1-138-33198-3 VL - 1 SP - 97 EP - 102 PB - NUMGE CY - Porto, Portugal AN - OPUS4-45721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - Relevant factors for the liquefaction susceptibility of cyclically loaded offshore monopiles in sand N2 - The offshore foundations may exhibit a relatively high liquefaction susceptibility due to the full saturation of the porous seabed and the cyclic nature of the typical offshore loads. Here, the particular relevance of some of the main factors that affect the liquefaction susceptibility of an offshore monopile will be addressed, focusing on the possibility of a progressive accumulation of residual pore water pressure within the saturated soil around a monopile under cyclic lateral loading. The discussion is based on numerical results obtained with a coupled FE model of the offshore foundation which includes the Biot-Zienkiewicz u-p model. A constitutive model of the Generalized Plasticity type has been used for the soil in order to reproduce important features of its behaviour under cyclic loading. This paper presents the findings derived from a parametric study of the problem and shows that the accumulation of residual pore pressure can produce significant changes of the pile's behaviour under external loading. The paper also investigates the effects caused by the loading from a realistic storm of moderate magnitude and the consequential transient degradation of the foundation's stiffness. T2 - Poromechanics V - 5th Biot conference on poromechanics CY - Vienna, Austria DA - 10.07.2013 KW - Soil liquefaction KW - Cyclic loads KW - Piles KW - Sand (hydraulic) KW - Offshore structures PY - 2013 SN - 978-0-7844-1299-2 DO - https://doi.org/10.1061/9780784412992.160 SP - 1336 EP - 1345 AN - OPUS4-28873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Offshore Wind Turbines: Pile foundations and the German praxis (Spanish: Aerogeneradores marinos. Cimentaciones mediante pilotes y práctica alemana) T2 - Symposium "New geotechnical frontiers in the energy and environmental engineering" CY - Madrid, Spain DA - 2013-06-24 PY - 2013 AN - OPUS4-29179 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Relevant Factors for the Liquefaction Susceptibility of Cyclically Loaded Offshore Monopiles in Sand T2 - Fifth Biot Conference on Poromechanics, ASCE CY - Vienna, Austria DA - 2013-07-10 PY - 2013 AN - OPUS4-29180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rücker, Werner A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Georgi, Steven T1 - Großversuche an Rammpfählen zur Ermittlung der Tragfähigkeit unter zyklischer Belastung und Standzeit N2 - Im Rahmen mehrerer vom Bundesumweltministerium geförderter Forschungsvorhaben untersucht die BAM Bundesanstalt für Materialforschung und -prüfung zusammen mit Partnern aus Industrie und Wissenschaft das Tragverhalten von zyklisch lateral und axial belasteten Rammpfählen für Offshore-Windkraftanlagen. Neben Modellversuchen im Labor werden hierbei auch Großversuche durchgeführt. In diesem Beitrag wird das neu erstellte Testfeld der BAM zur Prüfung von Pfählen in Horstwalde vorgestellt. In den laufenden Großversuchen werden Parameter wie Tragfähigkeitsminderung infolge zyklisch-axialer Lasten im Druck- und Zugbereich sowie die Zunahme von Tragfähigkeiten durch sogenannte Anwachseffekte untersucht. Bezüglich der zyklischen Belastungen werden insbesondere als unsicher anzunehmende Wertepaare in den derzeit verwendeten Interaktionsdiagrammen betrachtet, wobei hier das Hauptaugenmerk aber nicht nur auf dem Versagen des Pfahls, sondern auch auf der Ermittlung der Resttragfähigkeit nach definierten Zyklenzahlen liegt. Im Beitrag werden erste Ergebnisse zu den Anwachseffekten präsentiert und mit Ergebnissen aus der Literatur verglichen. Des Weiteren werden das Versuchsprogramm zu den zyklisch axial belasteten Pfählen vorgestellt und erste Ergebnisse gezeigt. In einem Ausblick werden weitere Ziele des Forschungsvorhabens beschrieben. Hierzu gehören die Validierung und Kalibrierung eines existierenden Modells zur Ermittlung der Tragfähigkeit unter zyklischer Belastung auf der Grundlage aktueller Messdaten am Pfahl.----------------------------------------------------------------------------------------------- Large-scale tests on driven piles for the investigation of pile capacity under cyclic loading and ageing effects. The cyclic behaviour of axially and laterally loaded piles for the foundation of offshore wind turbines is being investigated by the Federal Institute for Materials Research and Testing (BAM) in the frame of several research projects funded by the German Federal Ministry for the Environment and carried out in cooperation with industrial and academic partners. To this end, physical model tests in reduced scale as well as large scale field tests are being performed. This paper presents the new pile testing facility in the BAM's testing site at Horstwalde. The large-scale tests being performed there are aiming at the pile capacity degradation due to cyclic axial loading (both in tension and compression) as well as at the investigation of the capacity gains due to ageing effects (pile setup). Concerning the cyclic loading, the investigations have been mainly focused on special load combinations where there is little experience and where current interaction diagrams are loosely defined. However, the aim of the tests was not the cyclic failure, but rather the assessment of the post-cyclic capacity after the application of a pre-defined number of load cycles. Here, the testing program is summarised and some key results from the first testing campaign are discussed. The paper also presents some preliminary results concerning the capacity gains through ageing and compares them to previous experience from the literature. Finally, the paper gives an outlook on further goals of the current research projects, including the validation and calibration of a design model for the cyclic capacity of piles based on measured data from real piles. PY - 2013 DO - https://doi.org/10.1002/gete.201200021 SN - 0172-6145 SN - 1865-7362 SN - 2190-6653 VL - 36 IS - 2 SP - 77 EP - 89 PB - VGE Verl. GmbH CY - Essen AN - OPUS4-29517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bronsert, Jeffrey A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner ED - Dimitrovová, Z. ED - de Almeida, J.R. ED - Goncalves, R. T1 - Numerical modeling of train-track-interaction at bridge transition zones considering the long-term behaviour N2 - A train passage will induce elastic and plastic deformations in the ballast and ist underlying soll. Considering the short term behaviour the elastic deformations will overweight the plastic and therefore these can be neglected. Regarding the long term behaviour the plastic deformations will accumulate due to repeating traffic loads and lead to settlement and Deterioration ofthe track structure. A smooth settlement along the track (small differential Settlement) is acceptable, whereas large differential settlement accelerates the process of deterioration and reduces the safety and serviceability ofthe track. Especially a bridge transition zone is prone to large differential settlements, where the track deteriorates in the backfilling area of bridge abutments mainly due to stiffness changes between embankment and bridge, repeating traffic loads and displacements of the superstructure Ends on bridges. A numerical model will be presented, with a particular focus on the long term behaviour of the track at bridge transition zones under repeating traffic loads. The ahn ofthe Simulation is not the computation of every train Crossing but the analysis of the long term behaviour of the bridge transition zone based on single train crossings. The analysis is performed in the time domain, whereas the bridge, the track and the backfilling area are modelled by means of the finite T2 - ICOVP-2013 - 11th International conference on vibration problems CY - Lisbon, Portugal DA - 09.09.2013 KW - Train-track-interaction KW - Transition zone KW - Track settlement PY - 2013 SN - 978-989-96264-4-7 SP - 1 EP - 10 AN - OPUS4-29591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cuéllar, Pablo A1 - Mira, P. A1 - Pastor, M. A1 - Merodo, J.A.F. A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - A numerical model for the transient analysis of offshore foundations under cyclic loading N2 - A comprehensive numerical model for the analysis of offshore foundations under a general transient loading is presented here. The theoretical basis of the model lies on the Swansea formulation of Biot's equations of dynamic poroelasticity combined with a constitutive model that reproduces key aspects of cyclic soil behaviour in the frame of the theory of generalised plasticity. On the practical side, the adoption of appropriate finite element formulations may prevent the appearance of spurious numerical instabilities of the pore pressure field. In this respect, the use of a coupled enhanced-strain element is here proposed. On the other hand, the practicality of the presented model depends ultimately on its computational efficiency. Some practical recommendations concerning the solution strategies, the matrix storage/handling procedures and the parallel multi-processor computation are here provided. Finally, the performance of the model with a benchmark study case and its practical application to analyse the soil–structure interaction of an offshore monopile under a realistic transient storm loading are discussed. KW - Offshore foundations KW - Cyclic loading KW - Numerical model KW - Pore pressure accumulation KW - Liquefaction analysis PY - 2014 DO - https://doi.org/10.1016/j.compgeo.2014.02.005 SN - 0266-352x VL - 59 SP - 75 EP - 86 PB - Elsevier Ltd. CY - Barking AN - OPUS4-30490 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Georgi, Steven A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Karabeliov, Krassimire A1 - Rücker, Werner ED - Lutz, B. ED - Möller, G. ED - Rücker, Werner ED - Schiefelbein, N. T1 - Ermittlung von Beanspruchung und Verformungen von Pfahlgründungen - Messverfahren und Applikation N2 - Vor dem Hintergrund einer angestrebten größeren Unabhängigkeit der Energieversorgung von fossilen Energieträgern hat die Windenergie in den letzten Dekaden zunehmend an Bedeutung gewonnen. Dabei wird insbesondere die Energiegewinnung offshore in der Deutschen Nordsee, auf Grund dort vorhandener stetiger Winde und sinkender Akzeptanz von Windkraftanlagen an Land, forciert. Im Hinblick auf die Gründung dieser Anlagen wird technisches Neuland betreten. Angesichts von Wassertiefen bis über 25 m erhalten aufgelöste Gründungsstrukturen wie Tripod und Jacket oft den Vorzug vor Monopiles. Letztere waren wegen der geringen Produktions- und Installationskosten, der bisher am häufigsten angewandte Gründungstyp in flacheren Gewässern. Monopile- und Mehrpfahlgründung unterscheiden sich wesentlich im Abtrag der Belastung durch Beanspruchungen aus Wind und Wellen in den umgebenden Baugrund. Während beim Monopile die zyklischen Momente über laterale Bettung abgetragen werden, entstehen an den Mehrpfahlgründungen axiale Zug- und Druckbelastungspaare in gegenüberliegenden Pfählen. Die zyklischen Belastungen von Monopiles sind demnach hauptsächlich in lateraler Richtung zu erwarten, während für Mehrpfahlgründungen die zyklische Belastung einen überwiegend axialen Charakter aufweist. Die zyklischen axialen Lasten in den Pfählen der Mehrpfahlgründungen können die axialen Tragfähigkeiten insbesondere am Pfahlmantel reduzieren und damit evtl, zu einem Versagen der Gründung führen. T2 - Messen im Bauwesen 2014 - Neue Messtechnik und Anwendungsfälle CY - Berlin, Germany DA - 04.03.2014 KW - Zyklik KW - Pfahl KW - Tragfähigkeit KW - Dehnungsmessung PY - 2014 SN - 978-3-9815944-7-8 SP - 97 EP - 108 AN - OPUS4-30486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Bronsert, Jeffrey A1 - Cuéllar, Pablo A1 - Rücker, Werner ED - Chen, A. ED - Frangopol, D.M. ED - Ruan, X. T1 - Evaluating the degradation of ballasted track at bridges for high-speed railways N2 - The bridge design for railway bridges is far more dependent on the interaction with the traffic and the carriageway than for road bridges. This is especially true for the specific demands of the track in highspeed railways. Both maintenance and safety of the track have to be considered. The most relevant sections for the design criteria can be located at the bridge transition zones. Based on experimental investigations it is shown that bridge joint displacements, changes in stiffness and uplifting of the sleeper are causes for an increased degradation and loss in strength of the ballasted track. With respect to high speed vibrations of the bridge deck can have an even more decisive impact. Bridge deck vibrations can lead to destabilization of the bailast. In a numerical study the behavior of the track at the bridge is illustrated. T2 - IABMAS 2014 - 7th International conference of bridge maintenance, safety and management CY - Shanghai, China DA - 07.07.2014 KW - Train-track-bridge-interaction KW - Bridge transition zone KW - Assessment criteria KW - Vehicle model KW - Numerical model PY - 2014 SN - 978-1-138-00103-9 SN - 978-1-315-76069-8 SP - 1 EP - 8 PB - CRC Press AN - OPUS4-31142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bronsert, Jeffrey A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner ED - Cunha, A. ED - Caetano, E. ED - Ribeiro, P. ED - Müller, G. T1 - Assessment and optimisation of bridge transition zones on the basis of a numerical model for train-track-bridge interaction N2 - The main degradation process at bridge transition zones due to traffic loads is the appearance of differential settlements. Abrupt stiffness changes, repeating traffic loads and relative displacements of the superstructure ends on bridges often aggravate this problem. In this contribution, a 3D finite element (FE) model extended with a boundary formulation in the frame of the scaled-boundary finite element method (SBFEM) for a transient analysis of train-track-bridge interaction is presented. This numerical model permits an assessment of bridge transition zone with respect to permanent deformations of the track. The main focus lies on the modeling strategies for the vehicle and their impact on suitable assessment criteria for bridge transition zones. For this purpose, two different modeling strategies for the vehicle, a moving load model and a multibody model, have been compared and discussed on the basis of the assessment criteria. The results indicate that the model of the vehicle has a minor effect for an assessment on the embankment, but that the assessment on the bridge may show significant differences depending on whether the inertial components of the vehicle (multibody model) are considered. T2 - EURODYN 2014 - 9th International conference on structural dynamics CY - Porto, Portugal DA - 30.06.2014 KW - Train-track-bridge-interaction KW - Bridge transition zone KW - Assessment criteria KW - Vehicle model KW - Numerical model PY - 2014 SN - 978-972-752-165-4 SN - 2311-9020 SP - 799 EP - 804 AN - OPUS4-31144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Micromechanics of jet erosion on cohesive soils - A coupled LBM-DEM modelling approach N2 - Here we investigate the physical mechanisms behind the surface erosion of a cohesive granular soil induced by an impinging jet by means of numerical simulations coupling fluid and grains at the microscale. The 2D numerical model combines the Discrete Element and Lattice Boltzmann methods (DEM-LBM) and accounts for the granular cohesion with a contact model featuring a paraboloidal yield surface. Here we review first the hydrodynamical conditions imposed by the fluid jet on a solid granular packing, turning then the attention to the impact of cohesion on the erosion kinetics. Finally, the use of an additional subcritical debonding damage model based on the work of Silvani and co-workers provides a novel insight into the internal solicitation of the cohesive granular sample by the impinging jet. T2 - 8th International Conference on Micromechanics on Granular Media CY - Montpellier, France DA - 03.07.2017 KW - Micromechanical modelling KW - LBM-DEM KW - Jet erosion KW - Granular cohesion KW - Subcritical debonding PY - 2017 AN - OPUS4-41122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Erosive phenomena at the mesoscale – Perspectives and challenges using coupled LBM-DEM models N2 - The physical phenomena related to the erosion of granular materials by a fluid flow are ubiquitous and often present major challenges and threats to a wide range of civil engineering constructions and infrastructures. Catastrophic earth-dam failures and large sinkholes are just some of the possible outcomes of the different forms of erosion (a.o. surface erosion, suffusion, piping, backwards erosion, etc…). However, little is known about the actual mechanical origins of erosion, while the assessment of erodibility is generally performed by means of experimental tests and empirical correlations. Here we provide a general overview of some current research models aiming to clarify the micromechanical phenomena and their macromechanical consequences taking place in different erosion scenarios. The employed numerical techniques rely on the coupling of two well-stablished particle methods for the fluid and solid phases, namely the Lattice Boltzmann Method (LBM) and the Discrete Element Method (DEM) respectively. Further ingredients of our numerical models include an elastoplastic cohesion model for intergranular solid bridges and a subcritical debonding model for the simulation of transient damage processes within the soil matrix. T2 - 5th Int. Conference on Particle-based Methods (PARTICLES 2017) CY - Hannover, Germany DA - 26.09.2017 KW - Micromechanical modelling KW - Erosion KW - LBM-DEM PY - 2017 AN - OPUS4-42459 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geißler, Peter A1 - Cuéllar, Pablo A1 - Hüsken, Götz A1 - Kühne, Hans-Carsten A1 - Baeßler, Matthias T1 - Insights into compaction grouting for offshore pile foundations N2 - The authors are currently investigating the possibility to apply compaction grouting for offshore pile foundations (Jacket piles as well as monopiles) as a possible retrofitting technique for an optimised foundation concept. In this research project, we are developing a design approach aiming to predict the ideal amount and properties of a grout for a specific soil situation and desired improvement of pile bearing capacity after Installation and during service time. Both numerical and experimental tests have been carried out to investigate the injection process during which a highly viscous grout is injected into the soil under high pressure to displace and compact the surrounding soil without fracturing it. The implicit Material Point Method (MPM) based on a mixed formulation is the numerical technique chosen to deal with the expected large deformations and the arbitrary shape of the developing grout bulb. The usage of MPM prevents both the need of remeshing and the numerical instability induced by extensive mesh distortion. For validation with experimental results, we have constructed a testing chamber with one transparent sidewall. This chamber enables us to observe the injection process directly at the transparent vertical window and to measure the in-plane soil displacements and strains by means of the Digital Image Correlation (DIC) technique. The results already reveal the interrelation of soil and grout properties for a successful usage of this common ground improvement technique. T2 - 37th International Conference on Ocean, Offshore and Arctic Engineering (OMAE 2018) CY - Madrid, Spain DA - 18.06.2018 KW - Offshore pile foundation KW - Compaction grouting KW - Material Point Method (MPM) KW - Mixed formulation KW - Digital Image Correlation (DIC) PY - 2018 SN - 978-0-7918-5130-2 SN - 2153-4772 VL - 9 SP - V009T10A013, 1 EP - 9 AN - OPUS4-46004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines T1 - Cimentaciones profundas para aerogeneradores marinos N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided in two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of these two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Madrid, Spain DA - 13.04.2018 KW - Offshore pile foundations KW - Load bearing behaviour KW - Design methods PY - 2018 AN - OPUS4-46311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Victor, A. A1 - Lüddecke, F. ED - Triantafyllidis, T. T1 - Stability and large deformations of slender structures supported by soil materials N2 - The stability and geometric nonlinearities of slender structures are a major topic in structural design. While this topic is most relevant in the field of Structural Engineering, e.g. for steel or concrete structures, only few applications take the role of soil-structure-interaction explicitly into account. The focus of this paper is placed on the impact of soil support and its modelling for the buckling analysis based on examples both for pile foundations and for railway track stability. The general interaction between steel design and the geotechnical input will be addressed. The paper discusses and summarizes a range of subtopics based on experience and current research at the author’s institute. KW - Buckling soil-structure-interaction offshore piles track PY - 2020 SN - 978-3-030-28515-9 SN - 978-3-030-28516-6 DO - https://doi.org/10.1007/978-3-030-28516-6 SN - 1613-7736 SN - 1860-0816 VL - 91 SP - 355 EP - 369 PB - Springer CY - Cham, Switzerland AN - OPUS4-49166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Mechanical design challenges for offshore wind-farms N2 - This talk provides a brief introduction on general engineering aspects of offshore wind energy production. Some geomechanical issues for the foundation of OWTs into the seabed are introduced, while the results from experimental investigations and coupled computational analysis are discussed. In the second part of the seminar, the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. Concerning the geomechanical issues the talk shows that: i) The pile’s bearing capacity can degrade under cyclic loading (waves, wind, …). ii) The time effects can be relevant: Capacity improvement can be substantial, but also fragile. iii) There are cyclic PWP effects: Cyclic interaction with pore water may lead to soil softening and an uncoupled analysis (current design practice) is potentially unsafe. And concerning the hydromechanical and aerodynamical design considerations, this seminar shows that: i) Numerical analysis of turbine’s interaction with wind/waves is useful and affordable. ii) Simplified models can provide insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Energy Science Kolloquium, Fakultät für Physik, Universität Duisburg-Essen CY - Duisburg, Germany DA - 11.10.2018 KW - Geomechanics of offshore foundations KW - Wave-Tower interaction KW - Windfarm wake analysis PY - 2018 AN - OPUS4-46313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kemmler, Samuel A1 - Cuéllar, Pablo A1 - Rettinger, C. A1 - Köstler, H. T1 - A Fluid-Solid Coupled Micromechanical Simulation for the Analysis of Piping Erosion During the Seabed Installation of a Suction Bucket Foundation N2 - Suction buckets are a promising concept for the foundations of offshore wind turbines. During the installation process of a suction bucket, localized fluidization of the granular soil, so-called piping erosion, may lead to installation failure. A 3D fluid-solid coupled micromechanical simulation is presented to study the occurrence of piping. An Euler-Lagrangian coupling employs momentum exchange between the fluid phase and the geometrically resolved particles. We investigate the behavior of the soil for three cases with varying prescribed suction velocities. We observe piping in the case with the highest suction velocity by analyzing the deformation of the granular fabric and monitoring the differential pressure. The grains under the bucket wall-tip show the highest hydraulic gradients and forces at the onset of piping. This approach permits a detailed analysis of piping phenomena and brings novel insights on the triggering conditions for piping failure of suction-aided foundations. T2 - TC 105 International Symposium CY - Grenoble, France DA - 23.09.2024 KW - Micromechanical simulation KW - Piping erosion KW - Suction bucket foundation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629461 DO - https://doi.org/10.1088/1755-1315/1480/1/012024 SN - 1755-1307 VL - 1480 IS - 1 SP - 1 EP - 4 PB - IOP Publishing AN - OPUS4-62946 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kemmler, Samuel A1 - Cuéllar, Pablo A1 - Artinov, Antoni A1 - Luu, Li-Hua A1 - Farhat, Abbas A1 - Philippe, Pierre A1 - Rettinger, Christoph A1 - Köstler, Harald T1 - A fully-resolved micromechanical simulation of piping erosion during a suction bucket installation N2 - Granular fluidization phenomena such as piping erosion represent a challenge to the delicate installation process of offshore suction bucket foundations. A detailed analysis of the complex conditions in terms of soil composition, soil state, and foundation installation parameters that may lead to piping can be very demanding, if at all possible, solely by experimental means or using macroscopic continuum-based seabed models. The present paper presents a fully-resolved fluid-coupled micromechanical approach for a three-dimensional numerical simulation of the installation process of a suction bucket using the lattice Boltzmann method and discrete element method. The developed model is validated using well-established benchmarks and calibrated by means of experimental data from physical model tests on relevant scenarios focusing on the local fluidization of fixed embedded suction buckets as well as on the suction-driven installation of unrestrained buckets. The qualitative and quantitative agreement with the experimental data both endorse the proposed methodology and highlight the physical soundness of the obtained results. Thereby, the paper shows that three-dimensional analyses of relevant local scenarios at a real scale with little macromechanical model assumptions are feasible. KW - Micromechanical simulation KW - Fluid–solid coupling KW - Piping erosion KW - Suction bucket foundation KW - Offshore wind support structure KW - High-performance computing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-633790 DO - https://doi.org/10.1016/j.compgeo.2025.107375 SN - 0266-352X VL - 186 SP - 1 EP - 17 PB - Elsevier B.V. AN - OPUS4-63379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Schepers, Winfried T1 - VERBATIM: Project Introduction and Large Scale Experiments N2 - The presentation summarizes the scope of the joint project VERBATIM on buckling of large Monopiles. The presented work from the authors focusses on the experimental field tests of large predented piles during driving and a numerical investigation on the observed buckling behaviour. T2 - Colloquium „Buckling of Offshore Wind Energy Structures“ CY - Berlin, Germany DA - 14.02.2024 KW - Buckling KW - Offshore KW - Wind Energy Structures KW - Monopiles KW - Pile-Tip-Buckling PY - 2024 AN - OPUS4-59535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo T1 - Multivariate Gaussian Process for 3D subsurface stratigraphy prediction from CPT and labelled borehole data N2 - Quantifying uncertainties in subsurface properties and stratigraphy can lead to better understanding of the ground conditions and enhance the design and assessment of geotechnical structures. Several studies have utilized Cone Penetration Test (CPT) data and employed Bayesian and Machine Learning methods to quantify the geological uncertainty, based on the Robertson’s soil classification charts and the Soil Behaviour Type Index (Ic). The incorporation of borehole data can reduce the stratigraphic uncertainty. Significant challenges can arise, however, mainly due to the intrinsic differences between field and laboratory-based soil classification systems, which can potentially lead to inconsistent soil classification. To this end, this study proposes a multivariate Gaussian Process model that utilizes site-specific data and: i) jointly models multiple categorical (USCS labels) and continuous (Ic) variables, ii) learns a (shared) spatial correlation structure and the betweenoutputs covariance, and iii) produces two types of dependent classification outputs. The results indicate that the integration of geotechnical and geological information into a unified model can provide more reliable predictions of the subsurface stratification, by allowing simultaneous interpretation of USCS and Ic profiles. Importantly, the model demonstrates the potential to integrate multiple variables of different types, aiming to contribute to the development of a methodology for joint modeling of geotechnical, geological and geophysical data. T2 - 7th International Conference on Geotechnical and Geophysical Site Characterization CY - Barcelona, Spain DA - 18.06.2024 KW - Geotechnical site-characterization KW - Probabilistic KW - Soil classification KW - Gaussian Process PY - 2024 SP - 1733 EP - 1740 AN - OPUS4-60712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -