TY - JOUR A1 - Baeßler, Matthias A1 - Rücker, Werner A1 - Cuéllar, Pablo A1 - Georgi, Steven A1 - Karabeliov, Krassimire T1 - Großmaßstäblicher Versuchsstand für zyklisch axial belastete Pfähle N2 - Offshore-Pfähle in Mehrpfahlgründungsstrukturen wie Jacket-Gründungen müssen nach der Rammung überwiegend zyklisch axialen Belastungen widerstehen. Die Abmessungen der Pfähle werden sowohl von der inneren Tragfähigkeit und dem Ermüdungsverhalten des Stahlquerschnittes als auch von der äußeren Tragfähigkeit und der Pfahl-Boden-Interaktion bestimmt. Aufgrund der großen Zahl von Pfahlgründungen, die für aktuelle und zukünftige Windparkprojekte benötigt werden, besteht ein dringender Bedarf, die Dimensionierung und die damit verbundenen Kosten des Einzelpfahles zu optimieren. Bezüglich der Pfahltragfähigkeit sind wichtige aktuelle Forschungsthemen eine mögliche Traglaststeigerung durch Anwachsen und die geeignete Abschätzung der zyklischen Degradation. Zur Untersuchung beider Effekte wurde eine großmaßstäbliche Versuchsanlage auf dem Testgelände BAM TTS in Horstwalde nahe Berlin errichtet. Auf diesem Versuchsfeld können große Stahlrohrammpfähle zyklisch druck- und zugbelastet werden. Zudem kann die Untersuchung von Alterungseffekten durch zeitlichen Versatz zwischen den Messkampagnen untersucht werden. Erste Ergebnisse zeigen einen Anstieg der Pfahltragfähigkeit bis zu ca. 60 % nach einer Standzeit von ca. 18 Monaten. Für die Degradation der Tragfähigkeit der zyklisch belasteten Pfähle zeigen die ersten vorläufigen Ergebnisse ein zum Teil unerwartetes Verhalten. Zusätzliche Untersuchungen werden derzeit zur weiteren Abklärung durchgeführt. KW - Stahlpfahl, gerammt KW - Offshore-Gründung KW - Anwachsen KW - Feldversuch KW - Tragfähigkeit KW - Rammung KW - Offshore foundation KW - Increase KW - Field test KW - Bearing capacitiy KW - Driving Versuche - Experimental set-ups KW - Berechnungs- und Bemessungsverfahren - Analysis and calculation KW - Stahlhochbau - Steel buildings KW - Mast- und Turmbau - Masts and towers KW - Stahlwasserbau - Steel structures for hydraulic engineering KW - Steel pile, driven in PY - 2014 DO - https://doi.org/10.1002/stab.201430005 SN - 0038-9145 SN - 1437-1049 SN - 0932-6375 VL - 83 IS - Suppl. 1 (Erneuerbare Energien) SP - 26 EP - 32 PB - Ernst CY - Berlin AN - OPUS4-30898 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Farhat, Abbas A1 - Luu, Li-Hua A1 - Doghmane, Alexis A1 - Cuéllar, Pablo A1 - Benahmed, Nadia A1 - Wichtmann, Torsten A1 - Philippe, Pierre T1 - Micro and macro mechanical characterization of artificial cemented granular materials N2 - The focus of this study is the experimental characterization of cemented granular materials, with the aim of identifying the microscopic properties of the solid bonds and describing the extension to macroscopic mechanical strength of cemented samples.We chose to use artificially bonded granular materials, made of glass beads connected by solid paraffin bridges. The results of several sets of laboratory tests at different scales are presented and discussed. Micromechanical tests investigate the yield strength of single solid bonds between particles under traction, shearing, bending and torsion loading, as a function of variations in particle size, surface texture and binder content. Macro-scale tensile tests on cemented samples explore then the scale transition, including influence of confining walls through homothetic variations of the sample size. Despite the large statistical dispersion of the results, it was possible to derive and validate experimentally an analytical expression for micro tensile yield force as a function of the binder content, coordination number and grain diameter. In view of the data, an adhesive bond strength at the contact between bead and solid bond is deduced with very good accuracy and it is even reasonable to assume that the other threshold values (shear force, bending and torsion moments) are simply proportional to the tensile yield, thus providing a comprehensive 3D model of cemented bond. However, the considerable dispersion of the data at the sample scale prevents validation of the extended model for macroscopic yield stress. A final discussion examines the various factors that may explain intrinsic variability. By comparison with other more realistic systems studied in the literature in the context of bio-cementation, our artificial material nevertheless appears suitable for representing a cemented granular material. Being easy to implement, it could thus enable the calibration of discrete cohesion models for simulation of practical applications. KW - Cemented granular material KW - Micro-mechanical characterisation KW - Artificial soils KW - Yield tensile stress PY - 2024 DO - https://doi.org/10.1007/s10035-024-01426-2 SN - 1434-5021 VL - 26 IS - 3 SP - 1 EP - 20 PB - Springer CY - Berlin AN - OPUS4-63507 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kemmler, Samuel A1 - Rettinger, Christoph A1 - Rüde, Ulrich A1 - Cuéllar, Pablo A1 - Köstler, Harald T1 - Efficiency and scalability of fully-resolved fluid-particle simulations on heterogeneous CPU-GPU architectures N2 - Current supercomputers often have a heterogeneous architecture using both conventional Central Processing Units (CPUs) and Graphics Processing Units (GPUs). At the same time, numerical simulation tasks frequently involve multiphysics scenarios whose components run on different hardware due to multiple reasons, e.g., architectural requirements, pragmatism, etc. This leads naturally to a software design where different simulation modules are mapped to different subsystems of the heterogeneous architecture. We present a detailed performance analysis for such a hybrid four-way coupled simulation of a fully resolved particle-laden flow. The Eulerian representation of the flow utilizes GPUs, while the Lagrangian model for the particles runs on conventional CPUs. Two characteristic model situations involving dense and dilute particle systems are used as benchmark scenarios. First, a roofline model is employed to predict the node level performance and to show that the lattice-Boltzmann-based Eulerian fluid simulation reaches very good performance on a single GPU. Furthermore, the GPU-GPU communication for a large-scale Eulerian flow simulation results in only moderate slowdowns. This is due to the efficiency of the CUDA-aware MPI communication, combined with the use of communication hiding techniques. On 1024 A100 GPUs, an overall parallel efficiency of up to 71% is achieved. While the flow simulation has good performance characteristics, the integration of the stiff Lagrangian particle system requires frequent CPU-CPU communications that can become a bottleneck, especially when simulating the dense particle system. Additionally, special attention is paid to the CPU-GPU communication overhead since this is essential for coupling the particles to the flow simulation. However, thanks to our problem-aware co-partitioning, the CPU-GPU communication overhead is found to be negligible. As a lesson learned from this development, four criteria are postulated that a hybrid implementation must meet for the efficient use of heterogeneous supercomputers. KW - Discrete element method KW - Hybrid implementation KW - High-performance computing KW - Particulate flow KW - Lattice Boltzmann method PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623958 DO - https://doi.org/10.1177/10943420241313385 SN - 1741-2846 SP - 1 EP - 19 PB - SAGE Publications AN - OPUS4-62395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo T1 - Multivariate Gaussian Process Regression for 3D site characterization from CPT and categorical borehole data N2 - Accurate prediction of subsurface stratigraphy and geotechnical properties, along with quantification of associated uncertainties, is essential for improving the design and assessment of geotechnical structures. Several studies have utilized indirect data from Cone Penetration Tests (CPTs) and employed statistical and Machine Learning methods to quantify the geological and geotechnical uncertainty. Incorporating direct borehole data can reduce uncertainties. This study proposes a computationally efficient multivariate Gaussian Process model that utilizes site-specific data and: (i) jointly models multiple categorical (USCS labels) and continuous CPT variables, (ii) learns a non-separable covariance structure leveraging the Linear Model of Coregionalization, and (iii) predicts a USCS based stratigraphy and CPT parameters at any location within the 3D domain. The results demonstrate that integrating geotechnical and geological data into a unified model yields more reliable predictions of subsurface stratification, enabling the parallel interpretation of both USCS classification and CPT profiles. Importantly, the model demonstrates its potential to integrate multiple variables from different sources and data types, contributing to the advancement of methodologies for the joint modeling of geotechnical, geological, and geophysical data. KW - Geotechnical site-characterization KW - Cone Penetration Tests KW - Stratigraphy prediction KW - Multivariate Gaussian process KW - Variational inference KW - Linear Model of Coregionalization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629456 DO - https://doi.org/10.1016/j.enggeo.2025.108052 SN - 1872-6917 VL - 352 SP - 1 EP - 19 PB - Elsevier B.V. AN - OPUS4-62945 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cuéllar, Pablo A1 - Georgi, Steven A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - On the quasi-static granular convective flow and sand densification around pile foundations under cyclic lateral loading N2 - The saturated sand surrounding an offshore pile foundation under quasi-static cyclic lateral load can show the physical phenomena of macromechanical densification and convective granular flow. Based on the results from physical model tests at different geometrical scales, this paper provides a certain quantification of such phenomena and discusses their causes and consequences. The progressive sand densification leads to subsidence of the soil surface and a significant stiffening of the pile behaviour. Conversely, the ratcheting convective motion of two closed cells of soil beneath the pile-head is responsible for an endless grain migration at the soil surface, the inverse grading of the convected material and a direct shear of the sand at the distinct boundary of the revolving soil domain. In this respect, and from a macromechanical perspective considering the soil as a continuum, it appears that the convecting material tends to follow gradient lines of shear stress during its ratcheting motion. Concluding the paper, the practical relevance of these phenomena and their extrapolation to other conditions are briefly discussed. KW - Offshore pile foundation KW - Cyclic loading KW - Ratcheting KW - Granular convection KW - Densification PY - 2012 DO - https://doi.org/10.1007/s10035-011-0305-0 SN - 1434-5021 SN - 1434-7636 VL - 14 IS - 1 SP - 11 EP - 25 PB - Springer CY - Berlin ; Heidelberg AN - OPUS4-25405 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Pore-Pressure Accumulation and Soil Softening around Pile Foundations for Offshore Wind Turbines T2 - OMAE-2012 ASME Conference, Symposium 10 Offshore Geotechnics, Session 10-6 Piled Foundations CY - Rio de Janeiro, Brazil DA - 2012-07-01 PY - 2012 AN - OPUS4-26161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Benseghier, Z. A1 - Cuéllar, Pablo A1 - Luu, L.-H. A1 - Bonelli, S. A1 - Philippe, P. T1 - A parallel GPU-based computational framework for the micromechanical analysis of geotechnical and erosion problems N2 - This article deals with the relevance and practical feasibility of micromechanical simulations for their application to general geomechanical problems involving fluid-saturated granular assemblies, whether frictional or cohesive. A set of conceptual and numerical tools is here presented, advocating for a parallel computation using graphical processing units (GPUs) to treat large numbers of degrees of freedom with conventional Desktop computers. The fluid phase is here simulated with a particle-resolved approach in the frame of the Lattice Botzmann Method (LBM) while the granular solid phase is modelled as a collection of discrete particles from a Molecular Dynamics DEM perspective. The range of possible material behaviours for the solid granular phase is intended here to cover a broad spectrum from purely frictional to viscous cohesive materials with either brittle or transient debonding features. Specific details of the implementation and some validation cases are put forward. Finally, some exemplary applications in the fields of soil erosion and geotechnical profile installation are provided along with a discussion on the parallel performance of the presented models. The results show that a micromechanical approach can be feasible and useful in practice, providing meaningful insights into complex engineering problems like the erosion kinetics of a soil under an impinging jet or the penetration resistance of a deep foundation in a layered soil profile. KW - Offshore geomechanics KW - Erosion KW - Micromechanical modelling KW - LBM-DEM KW - GPU Parallel computing PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-502309 DO - https://doi.org/10.1016/j.compgeo.2019.103404 VL - 120 SP - Paper 103404, 1 PB - Elsevier Ltd. AN - OPUS4-50230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Balscheit, Hagen A1 - Geißler, Peter A1 - Cuéllar, Pablo A1 - Basedau, Frank A1 - Baeßler, Matthias T1 - Large-scale field tests on plastic pile tip failure upon monopile installation N2 - Large-diameter monopiles are the most common foundation structures for offshore wind turbines. One relevant failure mode during installation is plastic failure of the pile tip which may increase progressively during further driving (pile tip buckling; extrusion buckling). This paper presents the details and results of a large-scale field-test campaign with dynamic pile installation for the validation and calibration of different numerical approaches concerning pile-tip buckling phenomena. The phenomenology of observed pile-tip failures is here described in detail and a first quantitative approach is evaluated based on the field-test data. As the number of new projects continues to grow and the necessity to construct wind farms in challenging terrain increases, such field data-sets will become increasingly relevant. KW - Monopile KW - Offshore Windenergy KW - Pfahlfußbeulen KW - Pile Tip Buckling KW - Reference Tests PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-611651 DO - https://doi.org/10.1016/j.oceaneng.2024.119322 VL - 313 SP - 1 EP - 14 PB - Elsevier B.V. AN - OPUS4-61165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen A1 - Victor, A. A1 - Thiele, Marc A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Lüddecke, F. T1 - Experimental Investigation on Buckling Behavior of soil-embedded Piles N2 - Monopiles are currently the predominant foundation type for offshore wind turbines in Europe. Due to the increasing dimensions of the turbines, pile diameters beyond 10m become necessary. A design-relevant failure mode of monopiles is the local buckling of the pile wall in the embedded sections. Relevant buckling guidelines do not consider the soil-structure interaction specifically, although the embedment may allow for a reduction of wall thickness. However, Eurocode-based design concepts require a validation with comparative buckling cases for validation, either in terms of buckling curve parameters for both the algebraic stress-based and semi-numerical LBA/MNA design concept or as a calibration factor kGMNIA for fully numerical GMNIA calculations. These parameters are not yet available for embedded shells. To close this gap, we have conducted experiments on piles embedded in sand to investigate local buckling under soil-structure-interaction. The results will be used to calibrate numerical models. This research was carried out as part of the VERBATIM research project, funded by PTJ/BMWK and supported by the Carbon Trust's Offshore Wind Accelerator consortium. T2 - EUROSTEEL 2023 CY - Amsterdam, The Netherlands DA - 11.09.2023 KW - Wind KW - Wind Energy KW - Shell Buckling KW - Offshore KW - Soil-Structure-Interaction PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583641 DO - https://doi.org/10.1002/cepa.2313 SN - 2509-7075 VL - 6 IS - 3-4 SP - 1729 EP - 1734 PB - Ernst & Sohn Gmb AN - OPUS4-58364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo A1 - Baeßler, Matthias T1 - 3D spatial modelling of CPT data for probabilistic preliminary assessment of potential pile tip damage upon collision with boulders N2 - Tip damage of monopiles from boulder collisions during installation has emerged as a critical design issue, primarily due to the combination of the widespread use of large-diameter piles and the complexity of the ground conditions at the available sites. Recently, a framework relating potential pile tip damage to cone tip resistance from Cone Penetration Tests (CPTs) has been proposed in the literature. Gaussian processes are powerful stochastic models that enable probabilistic spatial interpolation of soil data at any location within a site. On this basis, this study utilizes sparse CPT data from a site in the North Sea, to first develop an efficient Gaussian process regression model, which is used to derive a three-dimensional (3D) probabilistic predictive map of the cone tip resistance. Assuming deterministic loading conditions and a factual collision with a boulder of pre-defined properties, the cone tip resistance predictive model is subsequently used for a probabilistic preliminary assessment of potential pile tip damage. Results of the analysis are realistic 3D probability maps of potential damage that aim to support engineering judgment and contribute towards cost-effective site investigation planning and offshore wind farm design. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG 2025) CY - Nantes, France DA - 09.06.2025 KW - CPT data KW - Gaussian process regression KW - Boulder impact KW - Preliminary pile tip damage assessment PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634417 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-323 SP - 505 EP - 510 PB - International Society for Soil Mechanics and Geotechnical Engineering CY - London AN - OPUS4-63441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Balscheit, Hagen A1 - Geißler, Peter A1 - Schepers, Winfried A1 - Cuèllar, Pablo T1 - Evaluation of pile tip buckling based on large scale tests N2 - Der Beitrag beschreibt eine groß angelegte Versuchskampagne mit Pfahlrammungen, um das Risiko des plastischen Versagens der Pfahlspitze besser zu verstehen und numerische Modelle zu validieren. Ein numerisches Modell mit transientem Bodenkontakt zeigt eine gute Übereinstimmung mit den Testergebnissen. Parametervariationen verdeutlichen, wie empfindlich die Pfahlreaktion auf Imperfektionen und Randbedingungen ist. T2 - 5TH INTERNATIONAL SYMPOSIUM ON FRONTIERS IN OFFSHORE GEOTECHNICS CY - Nantes, France DA - 09.06.2025 KW - Pile Tip Buckling KW - Monopile KW - Offshore Windenergy KW - Driving Refusal KW - Large Scale Test PY - 2025 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-476 SP - 1218 EP - 1223 PB - International Society for Soil Mechanics and Geotechnical Engineering (ISSMGE) CY - Nantes AN - OPUS4-63387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - System identification of inverse, multimodal and nonlinear problems using evolutionary computing - Application to a pile structure supported on nonlinear springs N2 - This paper deals with the system identification of a mechanical structure supported by nonlinear springs subjected to an external load. If all mechanical parameters of the system were known, the displacement of the system subjected to this load could be easily calculated. However, the monitoring applications often deal with the inverse problem. The loads and displacements of the system are known and certain mechanical Parameters of the system are sought. The solution of such inverse problems can be difficult, especially when they have a nonlinear and multimodal character, which often makes them appear intractable at first sight. However, evolutionary computing can be applied to solve this inverse, nonlinear and multimodal problem. Sometimes a prior knowledge exists on certain system properties, which is difficult to implement into analytical or numerical solvers. This knowledge can play a decisive role in identifying the System properties and it can be easily included as a boundary condition when applying evolutionary algorithms. This article discusses how and under what conditions the unknown spring resistances can be identified. The practical application of this procedure is exemplified here with the mechanical system of a pile foundation. KW - Evolutionary computing KW - Inverse problem KW - Multimodal solution KW - System identification KW - Pile monitoring PY - 2015 DO - https://doi.org/10.1016/j.engstruct.2015.07.034 SN - 0141-0296 SN - 1873-7323 VL - 101 SP - 609 EP - 620 AN - OPUS4-39310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kullolli, Borana A1 - Stutz, H. H. A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rackwitz, F. ED - Cardoso, A. S. ED - Borges, J. L. ED - Costa, P. A. ED - Gomes, A. T. ED - Marques, J. C. ED - Vieira, C. S. T1 - A generalized plasticity model adapted for shearing interface problems N2 - The response of many geotechnical systems, whose structural behavior depends on shearing effect, is closely related to soil structure interaction phenomenon. Experimentally it is found that the localisation of these effect happens at a narrow soil layer next to the structure. Numerically, this behavior can be modelled through inter-face elements and adequate constitutive models. In this work, a constitutive model in the framework of Gen-eralized Plasticity for sandy soils has been chosen to be adapted for the interface zone. From the direct shear experiments a sandy soil at loose and dense states under different normal pressures is considered. The adapted constitutive model is able to reproduce contraction and dilatation of the soil according to its relative density and it shows a good agreement with the experimental data. T2 - Conference CY - Porto, Portugal DA - 25.06.2018 KW - Numerical modelling KW - Soil-pile interaction KW - Interface KW - Shearing PY - 2018 SN - 978-1-138-33198-3 VL - 1 SP - 97 EP - 102 PB - NUMGE CY - Porto, Portugal AN - OPUS4-45721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - Relevant factors for the liquefaction susceptibility of cyclically loaded offshore monopiles in sand N2 - The offshore foundations may exhibit a relatively high liquefaction susceptibility due to the full saturation of the porous seabed and the cyclic nature of the typical offshore loads. Here, the particular relevance of some of the main factors that affect the liquefaction susceptibility of an offshore monopile will be addressed, focusing on the possibility of a progressive accumulation of residual pore water pressure within the saturated soil around a monopile under cyclic lateral loading. The discussion is based on numerical results obtained with a coupled FE model of the offshore foundation which includes the Biot-Zienkiewicz u-p model. A constitutive model of the Generalized Plasticity type has been used for the soil in order to reproduce important features of its behaviour under cyclic loading. This paper presents the findings derived from a parametric study of the problem and shows that the accumulation of residual pore pressure can produce significant changes of the pile's behaviour under external loading. The paper also investigates the effects caused by the loading from a realistic storm of moderate magnitude and the consequential transient degradation of the foundation's stiffness. T2 - Poromechanics V - 5th Biot conference on poromechanics CY - Vienna, Austria DA - 10.07.2013 KW - Soil liquefaction KW - Cyclic loads KW - Piles KW - Sand (hydraulic) KW - Offshore structures PY - 2013 SN - 978-0-7844-1299-2 DO - https://doi.org/10.1061/9780784412992.160 SP - 1336 EP - 1345 AN - OPUS4-28873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Offshore Wind Turbines: Pile foundations and the German praxis (Spanish: Aerogeneradores marinos. Cimentaciones mediante pilotes y práctica alemana) T2 - Symposium "New geotechnical frontiers in the energy and environmental engineering" CY - Madrid, Spain DA - 2013-06-24 PY - 2013 AN - OPUS4-29179 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Relevant Factors for the Liquefaction Susceptibility of Cyclically Loaded Offshore Monopiles in Sand T2 - Fifth Biot Conference on Poromechanics, ASCE CY - Vienna, Austria DA - 2013-07-10 PY - 2013 AN - OPUS4-29180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rücker, Werner A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Georgi, Steven T1 - Großversuche an Rammpfählen zur Ermittlung der Tragfähigkeit unter zyklischer Belastung und Standzeit N2 - Im Rahmen mehrerer vom Bundesumweltministerium geförderter Forschungsvorhaben untersucht die BAM Bundesanstalt für Materialforschung und -prüfung zusammen mit Partnern aus Industrie und Wissenschaft das Tragverhalten von zyklisch lateral und axial belasteten Rammpfählen für Offshore-Windkraftanlagen. Neben Modellversuchen im Labor werden hierbei auch Großversuche durchgeführt. In diesem Beitrag wird das neu erstellte Testfeld der BAM zur Prüfung von Pfählen in Horstwalde vorgestellt. In den laufenden Großversuchen werden Parameter wie Tragfähigkeitsminderung infolge zyklisch-axialer Lasten im Druck- und Zugbereich sowie die Zunahme von Tragfähigkeiten durch sogenannte Anwachseffekte untersucht. Bezüglich der zyklischen Belastungen werden insbesondere als unsicher anzunehmende Wertepaare in den derzeit verwendeten Interaktionsdiagrammen betrachtet, wobei hier das Hauptaugenmerk aber nicht nur auf dem Versagen des Pfahls, sondern auch auf der Ermittlung der Resttragfähigkeit nach definierten Zyklenzahlen liegt. Im Beitrag werden erste Ergebnisse zu den Anwachseffekten präsentiert und mit Ergebnissen aus der Literatur verglichen. Des Weiteren werden das Versuchsprogramm zu den zyklisch axial belasteten Pfählen vorgestellt und erste Ergebnisse gezeigt. In einem Ausblick werden weitere Ziele des Forschungsvorhabens beschrieben. Hierzu gehören die Validierung und Kalibrierung eines existierenden Modells zur Ermittlung der Tragfähigkeit unter zyklischer Belastung auf der Grundlage aktueller Messdaten am Pfahl.----------------------------------------------------------------------------------------------- Large-scale tests on driven piles for the investigation of pile capacity under cyclic loading and ageing effects. The cyclic behaviour of axially and laterally loaded piles for the foundation of offshore wind turbines is being investigated by the Federal Institute for Materials Research and Testing (BAM) in the frame of several research projects funded by the German Federal Ministry for the Environment and carried out in cooperation with industrial and academic partners. To this end, physical model tests in reduced scale as well as large scale field tests are being performed. This paper presents the new pile testing facility in the BAM's testing site at Horstwalde. The large-scale tests being performed there are aiming at the pile capacity degradation due to cyclic axial loading (both in tension and compression) as well as at the investigation of the capacity gains due to ageing effects (pile setup). Concerning the cyclic loading, the investigations have been mainly focused on special load combinations where there is little experience and where current interaction diagrams are loosely defined. However, the aim of the tests was not the cyclic failure, but rather the assessment of the post-cyclic capacity after the application of a pre-defined number of load cycles. Here, the testing program is summarised and some key results from the first testing campaign are discussed. The paper also presents some preliminary results concerning the capacity gains through ageing and compares them to previous experience from the literature. Finally, the paper gives an outlook on further goals of the current research projects, including the validation and calibration of a design model for the cyclic capacity of piles based on measured data from real piles. PY - 2013 DO - https://doi.org/10.1002/gete.201200021 SN - 0172-6145 SN - 1865-7362 SN - 2190-6653 VL - 36 IS - 2 SP - 77 EP - 89 PB - VGE Verl. GmbH CY - Essen AN - OPUS4-29517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bronsert, Jeffrey A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner ED - Dimitrovová, Z. ED - de Almeida, J.R. ED - Goncalves, R. T1 - Numerical modeling of train-track-interaction at bridge transition zones considering the long-term behaviour N2 - A train passage will induce elastic and plastic deformations in the ballast and ist underlying soll. Considering the short term behaviour the elastic deformations will overweight the plastic and therefore these can be neglected. Regarding the long term behaviour the plastic deformations will accumulate due to repeating traffic loads and lead to settlement and Deterioration ofthe track structure. A smooth settlement along the track (small differential Settlement) is acceptable, whereas large differential settlement accelerates the process of deterioration and reduces the safety and serviceability ofthe track. Especially a bridge transition zone is prone to large differential settlements, where the track deteriorates in the backfilling area of bridge abutments mainly due to stiffness changes between embankment and bridge, repeating traffic loads and displacements of the superstructure Ends on bridges. A numerical model will be presented, with a particular focus on the long term behaviour of the track at bridge transition zones under repeating traffic loads. The ahn ofthe Simulation is not the computation of every train Crossing but the analysis of the long term behaviour of the bridge transition zone based on single train crossings. The analysis is performed in the time domain, whereas the bridge, the track and the backfilling area are modelled by means of the finite T2 - ICOVP-2013 - 11th International conference on vibration problems CY - Lisbon, Portugal DA - 09.09.2013 KW - Train-track-interaction KW - Transition zone KW - Track settlement PY - 2013 SN - 978-989-96264-4-7 SP - 1 EP - 10 AN - OPUS4-29591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cuéllar, Pablo A1 - Mira, P. A1 - Pastor, M. A1 - Merodo, J.A.F. A1 - Baeßler, Matthias A1 - Rücker, Werner T1 - A numerical model for the transient analysis of offshore foundations under cyclic loading N2 - A comprehensive numerical model for the analysis of offshore foundations under a general transient loading is presented here. The theoretical basis of the model lies on the Swansea formulation of Biot's equations of dynamic poroelasticity combined with a constitutive model that reproduces key aspects of cyclic soil behaviour in the frame of the theory of generalised plasticity. On the practical side, the adoption of appropriate finite element formulations may prevent the appearance of spurious numerical instabilities of the pore pressure field. In this respect, the use of a coupled enhanced-strain element is here proposed. On the other hand, the practicality of the presented model depends ultimately on its computational efficiency. Some practical recommendations concerning the solution strategies, the matrix storage/handling procedures and the parallel multi-processor computation are here provided. Finally, the performance of the model with a benchmark study case and its practical application to analyse the soil–structure interaction of an offshore monopile under a realistic transient storm loading are discussed. KW - Offshore foundations KW - Cyclic loading KW - Numerical model KW - Pore pressure accumulation KW - Liquefaction analysis PY - 2014 DO - https://doi.org/10.1016/j.compgeo.2014.02.005 SN - 0266-352x VL - 59 SP - 75 EP - 86 PB - Elsevier Ltd. CY - Barking AN - OPUS4-30490 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Georgi, Steven A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Karabeliov, Krassimire A1 - Rücker, Werner ED - Lutz, B. ED - Möller, G. ED - Rücker, Werner ED - Schiefelbein, N. T1 - Ermittlung von Beanspruchung und Verformungen von Pfahlgründungen - Messverfahren und Applikation N2 - Vor dem Hintergrund einer angestrebten größeren Unabhängigkeit der Energieversorgung von fossilen Energieträgern hat die Windenergie in den letzten Dekaden zunehmend an Bedeutung gewonnen. Dabei wird insbesondere die Energiegewinnung offshore in der Deutschen Nordsee, auf Grund dort vorhandener stetiger Winde und sinkender Akzeptanz von Windkraftanlagen an Land, forciert. Im Hinblick auf die Gründung dieser Anlagen wird technisches Neuland betreten. Angesichts von Wassertiefen bis über 25 m erhalten aufgelöste Gründungsstrukturen wie Tripod und Jacket oft den Vorzug vor Monopiles. Letztere waren wegen der geringen Produktions- und Installationskosten, der bisher am häufigsten angewandte Gründungstyp in flacheren Gewässern. Monopile- und Mehrpfahlgründung unterscheiden sich wesentlich im Abtrag der Belastung durch Beanspruchungen aus Wind und Wellen in den umgebenden Baugrund. Während beim Monopile die zyklischen Momente über laterale Bettung abgetragen werden, entstehen an den Mehrpfahlgründungen axiale Zug- und Druckbelastungspaare in gegenüberliegenden Pfählen. Die zyklischen Belastungen von Monopiles sind demnach hauptsächlich in lateraler Richtung zu erwarten, während für Mehrpfahlgründungen die zyklische Belastung einen überwiegend axialen Charakter aufweist. Die zyklischen axialen Lasten in den Pfählen der Mehrpfahlgründungen können die axialen Tragfähigkeiten insbesondere am Pfahlmantel reduzieren und damit evtl, zu einem Versagen der Gründung führen. T2 - Messen im Bauwesen 2014 - Neue Messtechnik und Anwendungsfälle CY - Berlin, Germany DA - 04.03.2014 KW - Zyklik KW - Pfahl KW - Tragfähigkeit KW - Dehnungsmessung PY - 2014 SN - 978-3-9815944-7-8 SP - 97 EP - 108 AN - OPUS4-30486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -