TY - JOUR A1 - Bertovic, Marija A1 - Calmon, P. A1 - Carter, L. A1 - Fischer, J. A1 - Forsyth, D. A1 - Holstein, R. A1 - McGrath, B. A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Ronneteg, U. A1 - Rummel, W. A1 - Schubert, F. A1 - Selby, G. T1 - Summary of the "open space technology discussions" on reliability of NDE JF - Materials testing N2 - Since the beginnings of the European American Workshops (EAW) in 1997, the aim was to gather the experts in NDE reliability and discuss burning topics with the aim of identifying crucial problems and suggesting ways to move forward. This was usually achieved during the so-called break-out sessions, in which predetermined topics were discussed. During the 5th EAW, held in Berlin in 2013, this approach was replaced by an Open Space Technology (OST) approach. The benefit of this approach is seen in the freedom of topic choices, i. e., the topics are not predetermined but rather arise at that moment in that space and by the participants’ choice. The following topics arose: new reliability methods (Bayesian, MAPOD, …), structural health monitoring, definition of requirements of NDE by customer versus provider, what value of POD is good enough?, human factors, manual versus automated inspection, and basic concepts of reliability of NDE. The participants were encouraged to walk from one session to another and openly express their opinions. These were in the end summarized by a chosen group of moderators and presented in this paper. N2 - Seit den Anfängen der europäischen amerikanischen Workshops (EAW) im Jahr 1997 war es das Ziel, Experten auf dem Gebiet der ZfP-Zuverlässigkeit zusammenzuführen und aktuelle Themen zu diskutieren, um wichtige Probleme zu identifizieren und Wege für deren Lösung vorzuschlagen. Dies wurde in der Regel während der sogenannten „Break-out Sessions“ erreicht, in denen vorgegebene Themen diskutiert wurden. Während des 5. EAW, der in Berlin im Jahr 2013 stattfand, wurde dieser Ansatz durch einen Open Space Technology (OST) Ansatz ersetzt. Open Space ist eine Methode der Gruppenmoderation, die sehr gut geeignet ist, um neue Ideen zu entwickeln und selbstständiges Arbeiten zu fördern, d. h. die Themen werden nicht vorgegeben, sondern ergeben sich in diesem Moment in diesem Raum und durch die Wahl der Teilnehmer. Die folgenden Themen wurden herausgearbeitet: neue Zuverlässigkeitsmethoden (Bayes, MAPOD, ...…), Structural Health Monitoring, Definition von Anforderungen der Kunden gegenüber den ZfP-Anbietern, Welcher Wert der POD ist gut genug?, der Einfluss menschlicher Faktoren, manuelle gegenüber automatisierte Prüfung, sowie Grundkonzepte der ZfP-Zuverlässigkeit. Die Teilnehmer wurden aufgefordert, von einer Sitzung zur anderen zu wechseln und offen ihre Meinung zu äußern. Diese Meinungen wurden am Ende von einer ausgewählten Gruppe von Moderatoren zusammengefasst und werden in diesem Beitrag vorgestellt. KW - NDE reliability KW - POD KW - Bayesian approach KW - Structural health monitoring KW - Human factors KW - Open space technology PY - 2014 UR - http://www.hanser-elibrary.com/doi/pdf/10.3139/120.110604 DO - https://doi.org/10.3139/120.110604 SN - 0025-5300 VL - 56 IS - 7-8 SP - 602 EP - 606 PB - Hanser CY - München AN - OPUS4-31269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Calmon, P. A1 - Carter, L. A1 - Fisher, J. A1 - Forsyth, D. A1 - Holstein, R. A1 - McGrath, B. A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Ronneteg, U. A1 - Rummel, W. A1 - Schubert, F. A1 - Selby, G. T1 - Summary of the open space technology discussions T2 - 5th European-American workshop on reliability of NDE T2 - 5th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 SN - 978-3-940283-53-5 IS - DGZfP-BB 144 SP - 1 EP - 7(?) CY - Berlin AN - OPUS4-31271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bertovic, Marija A1 - Fahlbruch, B. A1 - Müller, Christina T1 - Human factors perspective on the reliability of NDT in nuclear applications JF - Materials testing N2 - Der Artikel beschreibt eine arbeitspsychologische Analyse des Einflusses der menschlichen Faktoren auf die Zuverlässigkeit zerstörungsfreier Prüfungen (ZfP). Im Zeitraum von 5 Jahren wurde eine Serie von Untersuchungen zur wiederkehrenden Prüfung in Kernkraftwerken sowie zur Prüfung von Komponenten für die Endlagerung von radioaktivem Abfall durchgeführt. Dieser Beitrag gibt einen Überblick über vier Studien, diskutiert ausgewählte experimentelle Ergebnisse, und schlägt sich daraus ergebende Möglichkeiten zur Optimierung des ZfP-Verfahrens, der Prüfanweisung sowie zur Schulung des Personals vor. Die experimentellen Ergebnisse haben gezeigt, dass sowohl hoher Zeitdruck als auch hohe psychische Arbeitsbeanspruchung die Qualität des Prüfungsergebnisses negativ beeinflussen. Auffällig waren die Einflüsse der Einteilung des Arbeitsplans, der Kommunikation, der Prüfanweisung, der Prüfaufsicht sowie der Demonstrationsübung. Die abgewandelte Fehlermöglichkeits- und Einflussanalyse (Failure Mode and Effects Analysis – FMEA) wurde zur Identifizierung potentieller menschlicher Risiken während der Datenaufnahme und deren Auswertung benutzt. Darauf basierend werden verschiedene Präventivmaßnahmen, wie z.B. menschliche Redundanz und Automatisierung vorgeschlagen, sowie sich daraus möglicherweise ergebende Probleme diskutiert. Die experimentellen Ergebnisse haben gezeigt, dass menschliche Redundanz bei kritischen Anwendungen, wie beispielweise der Fehleridentifizierung, zu anderen Fehlerquellen führen kann, wie “sozialem Faulenzen” bei den Prüfern. Die Verwendung automatisierter softwarebasierter Entscheidungshilfen zur Fehlererkennung bzw. Fehlergrößenbestimmung kann zu übersteigertem Vertrauen in das automatisierte System (automation bias) durch die Prüfer und somit zu Fehlentscheidungen führen. Dadurch kann die Zuverlässigkeit der Prüfung in ungewollter Weise beeinflusst werden. Um die Zuverlässigkeit und Sicherheit der technischen Prozesse zu gewährleisten ist es wichtig, als Hauptfehlerquelle nicht mehr nur das einzelne Individuum zu sehen, sondern ebenfalls die Organisation zu berücksichtigen. KW - Human factors KW - NDT reliability KW - Nuclear PY - 2013 DO - https://doi.org/10.3139/120.110431 SN - 0025-5300 VL - 55 IS - 4 SP - 243 EP - 253 PB - Hanser CY - München AN - OPUS4-28830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Fahlbruch, B. A1 - Müller, Christina A1 - Pitkänen, J. A1 - Ronneteg, U. A1 - Gaal, Mate A1 - Kanzler, Daniel A1 - Ewert, Uwe A1 - Schombach, D. T1 - Human factors approach to the acquisition and evaluation of NDT data T2 - 18th WCNDT - World conference on nondestructive testing (Proceedings) N2 - This paper gives an introduction to the field of human factors with the focus on their influence on the reliability of NDT in the nuclear energy production (in-service inspections) and final storage of highly radioactive nuclear waste. A set of methodological tools has been developed in the scope of three projects, namely: 1) a theoretical model describing potential human factors influencing manual ultrasonic inspection performance during inservice inspections in nuclear power plants; 2) a method for identifying potential human errors during acquisition and evaluation of data gathered with mechanized ultrasonic, radiographic and eddy-current systems, as well as visual testing with a remote camera (Failure Modes and Effects Analysis, FMEA); and 3) use of eye tracking methodology to optimize existing procedures and practices. The experimental results have shown that time pressure, mental workload and experience influence the quality of the inspection performance. Noticeable were influences from the organization of the working schedule, communication, procedures, supervision and demonstration task. Implementing human redundancy in critical tasks, such as defect identification, as well as using an automated aid (software) to help operators in decision making about the existence and size of defects, could lead to other kinds of problems, namely social loafing (excerpting less effort when working on tasks collectively as compared to working alone) and automation bias (uncritical reliance on the proper function of an automated system without recognizing its limitations and the possibilities of automation failure) that might affect the reliability of NDT in an undesired manner. T2 - 18th WCNDT - World conference on nondestructive testing CY - Durban, South Africa DA - 16.04.2012 KW - Human Factors KW - Time Pressure KW - 4-Eye Principle KW - Automation Bias KW - Nuclear Waste Storage KW - In-Service Inspection (ISI) KW - Nuclear Power Plants KW - Eye Tracking KW - Failure Modes and Effects Analysis (FMEA) PY - 2012 SN - 978-0-620-52872-6 SP - 1 EP - 10 (Paper 198) AN - OPUS4-27583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. T1 - Investigating human factors in manual ultrasonic testing: Testing the human factor model T2 - 4th European-American workshop on reliability of NDE / DGZfP-Proceedings N2 - The human factors approach relies on understanding the properties of human capability and limitations under various conditions and the application of that knowledge in designing and developing safe systems. Following the principles of MTO (Man Technology Organization) approach, emphasis should be given to the way people interact with technical as well as organizational systems. A model describing human factor influences in relation to the performance shaping factors and their effect on the manual ultrasonic inspection performance had been built and a part of it empirically tested. The experimental task involved repeated inspection of 18 flaws according to the standard procedure under no, middle and high time pressure. Stress coping strategies, mental workload of the task, stress reaction and organizational factors have been measured. The results have shown that time pressure, mental workload and experience influence the quality of the inspection performance. Organizational factors and their influence on the inspection results were rated as important by the operators. However, further research is necessary into the effects of stress. T2 - 4th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2009-06-24 KW - Human factors KW - Time pressure KW - Nuclear power plants KW - Ultrasonic testing PY - 2009 UR - http://www.ndt.net/article/reliability2009/Inhalt/th4a3.pdf SN - 978-3-940283-17-7 IS - DGZfP-BB 116 SP - 1 EP - 8 AN - OPUS4-20615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. T1 - Investigating human factors in manual ultrasonic testing: testing the human factors model JF - Insight N2 - The human factors approach relies on understanding the properties of human capability and limitations under various conditions and the application of that knowledge in designing and developing safe systems. Following the principles of the MTO (Man Technology Organisation) approach, emphasis should be given to the way people interact with technical as well as organisational systems. A model describing human factor influences in relation to the performance shaping factors and their effect on manual ultrasonic inspection performance had been built and a part of it empirically tested. The experimental task involved repeated inspection of 18 defects according to the standard procedure under no, middle and high time pressure. Stress coping strategies, the mental workload of the task, stress reaction and organisational factors have been measured. The results have shown that time pressure, mental workload and experience influence the quality of the inspection performance. Organisational factors and their influence on the inspection results were rated as important by the operators. However, further research is necessary into the effects of stress. KW - Human factors KW - Manual ultrasonic testing KW - In-service inspection KW - Nuclear power plants KW - Time pressure PY - 2011 DO - https://doi.org/10.1784/insi.2011.53.12.673 SN - 0007-1137 VL - 53 IS - 12 SP - 673 EP - 676 PB - British Institute of Non-Destructive Testing CY - Northampton AN - OPUS4-26083 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Schombach, D. T1 - Einfluss des Zeitdrucks auf die manuelle Ultraschallprüfung. Untersuchung zu menschlichen Faktoren auf die Ergebnisse zerstörungsfreier Prüfungen T2 - DGZfP-Jahrestagung 2011 N2 - Die übergeordnete Zielsetzung unserer Untersuchung bestand darin, am Beispiel von Prüfungen mit Ultraschall eine belastbare Aussage zum Einfluss der Arbeitsbedingungen des Prüfers auf die Qualität der Ergebnisse von zerstörungsfreien Prüfungen zu ermitteln und Möglichkeiten zur Minimierung ungünstiger Einflussfaktoren aufzuzeigen. Der Schwerpunkt der Untersuchung wurde auf die manuelle Ultraschallprüfung gelegt und der Faktor 'Zeitdruck' (in drei Stufen variiert) als die zu variierende physische Einflussgröße gewählt. Die Variation des Faktors Zeitdruck wurde gemäß dem Prozessmodell von der Erhebung psychologischer Faktoren, die das Individuum und die Organisation beschreiben, begleitet. Die Ultraschallprüfungen erfolgten mit zehn Prüfern am Großbehälter und an Vergleichskörpern mit eingebrachten Testfehlern (Nuten, Risse). Die ausgewählten Fehler waren typisch für Prüfaufgaben, die bei wiederkehrenden Ultraschallprüfungen in Kernkraftwerken von den Prüfern zu lösen sind. Die Prüfaufgabe bestand darin, die in den vorgegebenen Prüfabschnitten vorhandenen Reflektoren aufzufinden und deren Amplituden, Ortskoordinaten und Längenerstreckungen zu ermitteln. Als Bewertungsmaßstab für die Qualität der Prüfaussage und für den Einfluss des menschlichen Faktors diente die Präzision der gemessenen Werte. Die Ergebnisse zeigen einen hohen Einfluss des menschlichen Faktors auf das Prüfergebnis und eine Einwirkung des Zeitdrucks besonders auf die Präzision der Messwerte. Hierbei war die Wirkung des individuell wahrgenommenen Zeitdrucks zusammen mit der psychischen Arbeitsbeanspruchung signifikant. Es wurde unter anderem herausgearbeitet, dass durch eine gute Vorbereitung auf die Prüfung, z.B. durch die sorgfältige Einweisung und ein vorgeschaltetes Fertigkeitstraining an Vergleichskörpern, die Zuverlässigkeit der Prüfergebnisse verbessert werden kann. Insgesamt hatte der Faktor 'Organisation' neben der 'Erfahrung' einen hohen Einfluss auf das Leistungsvermögen der Prüfer. Die Projektergebnisse wurden im Abschlussbericht des Forschungsvorhabens SR2514 dargestellt, es wurden drei Empfehlungen zur Vorbereitung und Einweisung der Prüfer, zur Stärkung der Verantwortung der Prüfaufsicht und zum 4-Augen-Prinzip formuliert. Die Empfehlungen wurden in der KTA- Regel 3201.4 'Komponenten des Primärkreises von Leichtwasserreaktoren; Teil 4: Wiederkehrende Prüfungen und Betriebsüberwachung (RÄE Fassung 2010-11)', umgesetzt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Human factors KW - ZfP KW - Ultraschallprüfung KW - UT KW - Zeitdruck PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251610 UR - http://jt2011.dgzfp.de/Portals/jt2011/BB/mi2c3.pdf SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.2.C.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-25161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Human factors approach to the reliability of NDT in nuclear waste management in Sweden and Finland T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components (DGZfP-Proceedings) N2 - Nuclear power industry has the responsibility to manage and dispose of all radioactive waste from its plants. Finnish Posiva and Swedish SKB are leading in the world in the development of disposal of spent nuclear fuel. Their method consists of encapsulating spent nuclear fuel in copper canisters and depositing them in the bedrock at a depth of about 500 meters for the next 100 000 years, leaving the radioactivity to decrease naturally through the decay of the radioisotopes in it. The copper canisters, consisting of a copper tube, a lid and a bottom (which make the outer shell) and an insert made of a cast iron, need to be inspected for their structural integrity to ensure no critical defects are present in the materials and welds that could lead to a leakage of the waste into the environment. Data acquired by 4 different non-destructive testing (NDT) methods (i.e. UT, ET, RT and VT with a remote camera) are evaluated by skilled human operators and therefore could be subject to human error. Human Factors approach lies in identifying potential errors made by the human, their causes and ways of preventing them. A customized Failure Modes and Effects Analysis (FMEA) was conducted to anticipate possible human failures during the data evaluation. The results led to designing several experiments (e.g. diffusion of responsibility within the 4-eye principle, over trust in automated systems) which are being experimentally tested in ongoing projects. The results are expected to lead to the optimization of the procedures followed by the NDT operators and consequently to the improvement of the overall NDT reliability. T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components CY - Berlin, Germany DA - 2010-09-29 KW - Human factors KW - Reliability KW - NDT KW - Nuclear waste PY - 2010 UR - http://www.ndt.net/article/jrc-nde2010/papers/32.pdf SN - 978-3-940283-30-6 IS - DGZfP-BB 125 (Th.3.A.2) SP - 1 EP - 10 CY - Berlin AN - OPUS4-23925 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Ronneteg, U. A1 - Pitkänen, J. T1 - Holistic risk assessment and risk prevention approach to the mechanized NDT and the inspection procedure T2 - 5th European-American workshop on reliability of NDE T2 - 5th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 SN - 978-3-940283-53-5 IS - DGZfP-BB 144 SP - Lecture 20, 1 EP - 10 CY - Berlin AN - OPUS4-31270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Kanzler, Daniel A1 - Fahlbruch, B. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - 'Human factors' bei der Datenauswertung der zerstörungsfreien Prüfung am Beispiel der nuklearen Endlagerung T2 - DGZfP-Jahrestagung 2011 N2 - Für eine ganzheitliche Betrachtung der Sicherheit bei der zerstörungsfreien Prüfung (ZfP) ist es unvermeidlich neben der Technik auch den Prüfer und die Prüforganisation einzubeziehen. Die Prüfung der Unversehrtheit von Endlagerbehältern ist eine eine sicherheitstechnisch wichtige Anwendung. Die Betreiber der geplanten finnischen und schwedischen Endlager, Posiva und SKB, kapseln den radioaktiven Abfall in Kupferkanistern ein und deponieren die Kanister dann in Felsgestein in einer Tiefe von ca. 500m. Die Kanister bestehen aus einem zylinderförmigen Kupfermantel mit einem Deckel und einem Boden, die zusammen die Außenumhüllung ergeben sowie einer Gusseisenmatrix für die Brennstäbe. Alle Komponenten werden auf ihre Dichtheit bzw. strukturelle Unversehrtheit mittels zerstörungsfreier Prüfmethoden geprüft, um sicher zu stellen, dass im Material und in den Schweißnähten keine kritischen Defekte vorhanden sind, die zu Freisetzungen in die Umgebung führen könnten. Vier ZfP Methoden (Ultraschall-, Wirbelstrom- und radiographische Prüfung, und die visuelle Prüfung anhand einer Kamera) werden mechanisiert durchgeführt, die gewonnenen Daten werden von qualifizierten Fachleuten ausgewertet und bieten so die Möglichkeit, dass Fehler entstehen. Das 'Human Factor'- Untersuchungskonzept besteht aus der Identifizierung potenzieller menschlicher Fehler, deren Ursachen und Präventionsmethoden. Mit Hilfe einer abgewandelten FMEA (Failure Modes and Effects Analysis) wurden mögliche Risiken identifiziert, die die Wahrscheinlichkeit für das Auftreten menschlicher Fehler bei der Datenauswertung erhöhen. Einige dieser Risiken sind beispielsweise Verantwortungsdiffusion beim 4-Augen-Prinzip, Übervertrauen in die Technik bei der automatischen Identifikation von Defekten sowie der Aufmerksamkeitsverlust bei dynamischer Bildbetrachtung. Deren Wirkung wird derzeit experimentell überprüft, um Ansatzpunkte für Optimierungen zu ermitteln und damit die Gesamtzuverlässigkeit des Systems zu verbessern. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Human factors KW - UT KW - ET KW - ZfP KW - Nukleare Endlagerung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251584 UR - http://jt2011.dgzfp.de/Portals/jt2011/BB/p42-ku~1.pdf SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P 42) SP - 1 EP - 2 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25158 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brekow, Gerhard A1 - Müller, Christina A1 - Tessaro, Ute T1 - Ultraschalluntersuchungen an elektronenstrahl- und reibrührgeschweißten Kupfer-Proben T2 - ZfP in Forschung, Entwicklung und Anwendung - Jahrestagung 2005 T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - Ultraschallprüfung KW - Fehlernachweis KW - Tauchtechnik KW - Durchschallungstechnik KW - Referenzverfahren KW - C-Bild-Darstellung PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-11765 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fücsök, F. A1 - Müller, Christina A1 - Rosenthal, Martina T1 - Some Results of the RRT of the Radiographic Film Evaluation T2 - MATEST 2003 T2 - MATEST 2003 NDT Achievements and Challenges CY - Brijuni-Pula, Croatia DA - 2003-09-28 KW - Reliability KW - Human factor KW - Radiographic film evaluation PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 1(?) EP - 11(?) AN - OPUS4-2783 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fücsök, F. A1 - Müller, Christina A1 - Rosenthal, Martina T1 - Reliability of Routine Radiographic Film Evaluation - an Extended ROC Study of the Human Factor T2 - Proceedings of the 8th ECNDT N2 - Many radiographic exposures and film evaluations are made daily in a typical industrial NDT laboratory. But questions remain regarding the precise probability of detecting discontinuities, including the reliability of each individual inspector or laboratory. Although most experienced inspectors of the laboratories evaluate each radiograph, the actual quantitative reliability of each of these inspectors remains unknown. In order to estimate the performance of representative inspectors and laboratories involved in NDE, volunteer laboratories from Croatia and Hungary conducted a series of round-robin inspections using X-ray films of welds. While the RRT is still in progress, the authors try to summarize the results of the “second round” and discuss the evaluation method. The results of the “first round” had been reported already. The focus is here to present the new results in terms of additional inspectors and a new more field oriented evaluation scheme. So far the results of a total of 35 inspectors of the different laboratories were evaluated. Those inspectors were selected who have done usually the work of radiographic film interpretation. They have from a half up to 35 years professional experience. For better overview we created four groups: maximum 4 year-experience, from 5 to 12 year-experience, from 15 to 25 year- experience and from 26 to 35 year-experience. Discussing the circumstances of the RRT with the participants, many of them expressed, they could not exactly follow the prescription of the test. According to their professional experience the small discontinuities can be omitted because of the strictest acceptance level accept them. So the most experienced evaluators did not write the small gases and slags into the list, which yield a wrong reliability of detection. As a consequence we should accomplish two types of evaluation: taking into consideration of all discontinuity and only the bigger once they are over the acceptance level. In addition we analyzed the “true values” in a critical review. These developments were made and the new results of the evaluation of the testers were more precise and reliable. The corresponding results are evaluated and presented in a ROC diagram where the p(TP) is plotted against the p(FP). The p(TP) means the probability of a true positive indication (correct defect finding) and p(FP) means the probability of a false positive (false alarm) indication. From the mean value of all inspectors maximum operation points we can estimate a representative overall reliability in terms of a correct indication rate of about 68 % (64 % new) and a false call rate of about 17 % (8 % new). This is a reasonable result within the strict 1 cm score. T2 - 8th ECNDT CY - Barcelona, Spain DA - 2002-06-17 PY - 2002 UR - http://www.ndt.net/article/ecndt02/429/429.htm N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. PB - European Federation for Non-Destructive Testing CY - Barcelona AN - OPUS4-2022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Gaal, Mate A1 - Bertovic, Marija A1 - Müller, Christina A1 - Zickler, S. A1 - Fahlbruch, B. A1 - Spokoiny, V. A1 - Schombach, D. A1 - Just, Tilman A1 - Cramer, H.-J. T1 - Untersuchungen zum Einfluss menschlicher Faktoren auf das Ergebnis von zerstörungsfreien Prüfungen, Möglichkeiten zur Minimierung dieses Einflusses und Bewertung der Prüfergebnisse T2 - Ressortforschungsberichte zur kerntechnischen Sicherheit und zum Strahlenschutz KW - Menschliche Faktoren KW - ZfP KW - Manuelle Ultraschallprüfung KW - WkP KW - KKW PY - 2009 IS - BfS-Projekt SR 2514 / Endbericht SP - 1 EP - 79 CY - Salzgitter AN - OPUS4-26081 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gaal, Mate A1 - Bär, Sylke A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Bloodworth, T. A1 - Lewis, A. A1 - Guelle, D. ED - Harmon, R. S. T1 - Optimizing detector trials for humanitarian demining T2 - Detection and remediation technologies for mines and minelike targets IX T2 - Conference 2004 CY - Orlando, FL, USA DA - 2004-04-12 KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2004 SN - 0-8194-5338-2 DO - https://doi.org/10.1117/12.541124 SN - 1605-7422 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 5415 SP - 1323 EP - 1334 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-6045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gaal, Mate A1 - Müller, Christina ED - Proske, D. T1 - Statistical design of experiments applied to tests of metal detectors used for mine detection T2 - 4th International Probabilistic Symposium : 12th - 13th October 2006 T2 - 4th International Probabilistic Symposium CY - Berlin, Germany DA - 2006-10-12 KW - Zuverlässigkeit in der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2006 SN - 3-00-019232-8 SP - 253 EP - 264 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-14297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Müller, Christina A1 - Ewert, Uwe A1 - Wilrich, P.-Th. A1 - Spyra, W. T1 - Trial Design for Testing and Evaluation of Metal Detectors Used in Humanitarian Landmine Clearance T2 - 9th European Conference on NDT T2 - 9th European Conference on NDT CY - Berlin, Germany DA - 2006-09-25 KW - Zuverlässigkeit in der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2006 SN - 3-931381-86-2 SP - 1(?) EP - 10(?) PB - European Federation for Non-Destructive Testing CY - Berlin AN - OPUS4-14420 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Müller, Christina A1 - Osterloh, Kurt A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Guelle, D. A1 - Lewis, A. T1 - Metal Detector Test Trials in Germany and Croatia - ITEP Project 2.1.1.2 T2 - MATEST 2003 T2 - MATEST 2003 NDT Achievements and Challenges CY - Brijuni-Pula, Croatia DA - 2003-09-28 KW - Demining KW - Metal detectors KW - Reliability tests KW - ROC diagrams KW - Test and evaluation KW - CWA07 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 1(?) EP - 15(?) AN - OPUS4-2784 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gianneo, A. A1 - Carboni, M. A1 - Müller, Christina A1 - Ronneteg, U. T1 - PAUT inspection of copper canister: structural attenuation and POD formulation JF - AIP Conferece Proceedings N2 - For inspection of thick-walled (50mm) copper canisters for final disposal of spent nuclear fuel in Sweden, ultrasonic inspection using phased array technique (PAUT) is applied. Because thick-walled copper is not commonly used as a structural material, previous experience on Phased Array Ultrasonic Testing for this type of application is limited. The paper presents the progress in understanding the amplitudes and attenuation changes acting on the Phased Array Ultrasonic Testing inspection of copper canisters. Previous studies showed the existence of a low pass filtering effect and a heterogeneous grain size distribution along the depth, thus affecting both the detectability of defects and their "Probability of Detection" determination. Consequently, the difference between the first and second back wall echoes were not sufficient to determine the local attenuation (within the inspection range), which affects the signal response for each individual defect. Experimental evaluation of structural attenuation was carried out onto step-wedge samples cut from full-size, extruded and pierced&drawn, copper canisters. Effective attenuation values has been implemented in numerical simulations to achieve a Multi Parameter Probability of Detection and to formulate a Model Assisted Probability of Detection through a Monte-Carlo extraction model. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) CY - Minneapolis, MN, USA DA - 26.07.2015 KW - Phased array ultrasonic testing KW - POD KW - Copper PY - 2016 DO - https://doi.org/10.1063/1.4940649 SN - 0094-243X VL - 1706 SP - Article: 200005, 1 EP - 13 PB - AIP Publishing AN - OPUS4-37592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holstein, R. A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Müller, Christina T1 - NDT reliability in the organizational context of service inspection companies JF - Materials Testing N2 - The focus of NDT reliability research in the past was in the field of two high risk industries: (atomic) power plants and aircrafts. The responsible organizations have been well aware of the risks and founded projects to understand and optimize critical steps during production, operation and maintenance. But the use of NDT is not limited to these two fields. The risks during operation of chemical plants, trains or windmills are different from the area above but evident. The coverage by legal regulations is relatively low. Instead of this owner responsibility, product liability and financial issues are the driving forces to do inspections and to use non-destructive testing. The different targets and financial issues influence the practice of NDT-inspections. A survey of this practice and its results are shown. N2 - Der Schwerpunkt der Forschung auf dem Gebiet der Zuverlässigkeit in der ZfP lag in der Vergangenheit in Bereichen mit hohen Risiken: (Kern-)Kraftwerke und Luftfahrt. Die verantwortlichen Organisationen waren sich der Risiken sehr bewusst und beauftragten Projekte zum Verständnis und zur Optimierung kritischer Schritte während der Herstellung, des Betriebs und der Wartung. Die Anwendung der ZfP ist jedoch nicht auf diese beiden Bereiche beschränkt. Die Risiken während des Betriebs von chemischen Anlagen, Eisenbahnzügen oder Windkraftanlagen unterscheiden sich von den oben genannten, sind jedoch erwiesen. Der Regelungsumfang durch Gesetze ist relativ gering. Stattdessen sind die Betreiberverantwortung, Produkthaftung und finanzielle Risiken die treibenden Kräfte, Inspektionen durchzuführen und zerstörungsfreie Prüfungen zu nutzen. Diese unterschiedlichen Ziele und finanziellen Rahmenbedingungen beeinflussen die Praktik der ZfP. Eine Untersuchung dieser Vorgehensweise und deren Ergebnisse werden hier dargestellt. KW - NDT reliability KW - Legal regulations KW - Product liability KW - NDT practice KW - Service inspection companies PY - 2014 UR - http://www.hanser-elibrary.com/doi/pdf/10.3139/120.110601 DO - https://doi.org/10.3139/120.110601 SN - 0025-5300 VL - 56 IS - 7-8 SP - 607 EP - 610 PB - Hanser CY - München AN - OPUS4-31268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holstein, R. A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Müller, Christina T1 - NDT reliability in the organizational context of service inspection companies T2 - 5th European-American workshop on reliability of NDE T2 - 5th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 SN - 978-3-940283-53-5 IS - DGZfP-BB 144 SP - Lecture 32, 1 EP - 7 CY - Berlin AN - OPUS4-31272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holstein, R. A1 - Müller, Christina T1 - Analyzing the reliability of non-destructive tests using the modular modell - a practical approach T2 - Proceedings of the 19th World Conference on Non-Destructive Testing N2 - Non-destructive testing is an important tool to guarantee the safety of railway traffic. The infrastructure with tracks, switches and sleepers is regularly tested, the locomotives and wagons with their wheels, bogies and axles as well. Many years of experience and some events lead in Germany to a good practice in testing the railway components. Now, European authorities are drafting a system of common requirements and standards for the European Railway Market. The German practice combines an intensive training of the NDT-personnel including sufficient time for practical exercises with organizational measures of the companies, responsible for rolling stock and infrastructure. Through the example of UT-testing of railway axles it will be shown, how training and organizational measures influence the reliability of such testing. T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - Modular model KW - Railway KW - Human factors PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-375712 UR - http://www.ndt.net/article/wcndt2016/papers/mo1d4.pdf SP - id 19519, 1 EP - 6 AN - OPUS4-37571 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kanzler, D. A1 - Müller, Christina T1 - How much information do we need? A reflection of the correct use of real defects in POD-evaluations JF - AIP Conference Proceedings N2 - To evaluate the capability of a non destructive testing system the “truth” of the used defects is essential. But what exactly is the truth of a real defect? And how much information is usable for the study? This presentation gives an overview about an advanced use of multiple metallographic cuts for the POD evaluation. In the presentation an approach is shown where information of metallographic studies are reconstructed and weighted to gain the essential information about real defects and which information are important for the detection with radiographic testing equipment. Furthermore, different connection points are discussed were additional knowledge from simulation and artificial defects can be used to gain additional certainty for the result of the evaluation. The methodology is used for the evaluation for the digital radiographic testing system for the testing of electron-beam welds, which is one possible choice to seal the Finnish copper canisters for the final deposit of spent nuclear fuel. T2 - 42nd annual review of progress in quantitative nondestructive evaluation: Incorporating the 6th European-American Workshop on Reliability of NDE CY - Minneapolis, MN, USA DA - 25.07.2015 KW - NDT KW - POD KW - Radiography PY - 2016 DO - https://doi.org/10.1063/1.4940652 SN - 0094-243X VL - 1706 SP - 200008-1 EP - 200008-7 PB - AIP Publishing AN - OPUS4-37596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, D. A1 - Müller, Christina T1 - Evaluating RT systems with a new POD approach T2 - Proceedings of the 19th World Conference on Non-Destructive Testing N2 - The usefulness and purpose of evaluating nondestructive testing (NDT) systems and their capabilities has changed in the last decade. The conventional method of simply applying a familiar statistical algorithm to say whether the system is usable for the tasks is history. Nowadays, multiple parameter methods which describe the probabilities of detection (POD) of different systems or real defects need new characteristics and a broader variety of statistical models to describe the true system behaviour. The appraisal of the NDT system involves diverse departments within a company (engineering, NDT-operators, and statisticians), but is, at the same time, more needed and requested than in the past. In this article, an approach is discussed in which professionals from different fields worked well together, accomplishing cost-intensive metallographic studies in correlation with well-understood physical behaviour of NDT-methods as well as deep-discussed mathematical methods to create a holistic evaluation of the technical reliability for a specific radiographic testing (RT) equipment. The first part of the publication will show the comparison between metallographic grinding and the RT indications. An essential innovation over past evaluation methods was the use of a multi-scale smoothing algorithm, which describes physical parameters, which were not used in evaluation like the POD in this way in the past. In the second part the statistical requirements for the POD take the focus. It can often be hard to make significant statements; especially in the case where only a small amount of data is available. The combination of data and the use of knowledge from simulations are essential. One possible solution will be shown for the RT evaluation. The methodology is used for evaluating the digital RT system for the inspection of electron-beam welds, which was method considered to seal the Finnish copper canisters for the final deposit of spent nuclear fuel. T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - POD KW - RT PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-375732 UR - http://www.ndt.net/article/wcndt2016/papers/we1d4.pdf SP - id 19535, 1 EP - 8 AN - OPUS4-37573 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Milsch, Steffen A1 - Pavlovic, Mato A1 - Müller, Christina A1 - Pitkänen, J. T1 - Concept of total reliability of NDT methods for inspection of the EB weld of the copper canister used for a long-term storage of spent nuclear fuel T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components (DGZfP-Proceedings) T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components CY - Berlin, Germany DA - 2010-09-29 KW - POD KW - Ultrasonic testing KW - Radiographic testing KW - Eddy current testing PY - 2010 SN - 978-3-940283-30-6 IS - DGZfP-BB 125 (Th.3.A.5) SP - 1 EP - 6 CY - Berlin AN - OPUS4-23924 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Ewert, Uwe A1 - Pitkänen, J. T1 - Einsatz der Bayes'schen Statistik in der Zuverlässigkeitsbestimmung von zerstörungsfreien Prüfsystemen JF - Materials Testing N2 - Die Fehlerauffindwahrscheinlichkeit oder 'Probability of Detection' ist zu einer wichtigen Qualitätskennzahl von zerstörungsfreien Prüfsystemen geworden. Die Einschätzung von nur künstlichen Fehlern ist jedoch als Bewertungsgrundlage meist nicht ausreichend. Die später verwendeten Prüfobjekte mit den real vorkommenden Fehlern sind die zu betrachtende Basis, für die der Endanwender eine gültige Qualitätseinschätzung der angewandten zerstörungsfreien Prüfung fordert. Jedoch ist bei dem Fall, dass die Datenmenge gering ist, auch die Aussage der POD beschränkt. Es muss daher eine Zwischenlösung gefunden werden, in der die Informationen von beiden Prüfungen kombiniert werden. Die Mathematik ermöglicht mit der Bayes'schen Statistik, diese Informationen miteinander zu kombinieren und somit beide Informationen in die Bewertung einfließen zu lassen. Dabei spielt jedoch der Zusammenhang zwischen Signal und Fehlerausprägung eine wichtige Rolle. Praktisch angewendet und erprobt wird diese Vorgehensweise für die Bewertung der zerstörungsfreien Prüfungen der Firma POSIVA, die sich mit dem Bau eines Endlagers für hochradioaktiven Abfall in Finnland beschäftigt. KW - POD KW - RT KW - Bayes'sches updating PY - 2013 DO - https://doi.org/10.3139/120.110432 SN - 0025-5300 VL - 55 IS - 4 SP - 254 EP - 260 PB - Hanser CY - München AN - OPUS4-28832 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. T1 - Konzept für den Einsatz der Bayes'schen Statistik: In der Zuverlässigkeitsbestimmung von zerstörungsfreien Diagnosesystemen - Das Problem zu kleiner experimenteller Datenmengen T2 - DGZfP-Jahrestagung 2011 N2 - Die statistische Qualitätskennzahl 'Probability of Detection (POD)' hängt von der Anzahl der zugrunde liegenden, brauchbaren Ergebnisse ab. Ist die Datenmenge niedrig, so ist auch die Aussage der POD eher beschränkt. Dennoch heißt eine große Zahl von Daten, nicht gleichzeitig, dass die POD für den realen Einsatz in der Produktion genügt. Es muss unterschieden werden, auf welcher Basis – unter welchen konkreten Bedingungen - die Daten erhoben wurden. Als wichtigste Ergebnisse zählen die Messergebnisse aus der Produktion der später verwendeten Prüfobjekte für den konkreten Einsatz. Noch bevor die zerstörungsfreien Prüfmethoden zuverlässig in der Produktion eingesetzt wurde, muss jedoch nachgewiesen werden, dass die real vorkommenden Fehler gefunden werden können. Das bedeutet, zu einem Zeitpunkt, an dem noch nicht ausreichend Daten vorhanden sind. Während für die realistische Prüfung die notwendige Anzahl der verschiedenen Fehler meist nicht erreicht wird, so fehlen bei der Bewertung der künstlichen Fehler wichtige Parameter und Einflussgrößen. Es muss somit eine Zwischenlösung gesucht werden, in der die Informationen von beiden Prüfungen kombiniert werden. Mit der Bayes’schen Statistik ermöglicht die Mathematik diese Informationen miteinander zu kombinieren und somit beide Informationen mit in die Bewertung einfließen zu lassen. Praktisch angewandt und erprobt wird die Vorgehensweise gemeinsam mit der Firma POSIVA, die sich mit dem Bau eines Endlagers für hoch-radioaktiven Abfall in Finnland beschäftigt. Hier wird als eine der technischen Barrieren ein Kupferbehälter für die Aufbewahrung der verbrauchten Brennstäbe genutzt. Dieser Kupferbehälter wird mit mehreren zerstörungsfreien Prüfmethoden geprüft. Anhand von Radiographiedaten wird gezeigt, dass die Aussagekraft der realistischen Fehlerdaten mit Hilfe der künstlichen Referenzfehlerdaten untermauert werden kann. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Bayes'sche Statistik KW - POD KW - Fehlende Datenmenge PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251598 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.3.C.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25159 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. T1 - Evaluation of radiographic testing performance with an advanced POD approach T2 - 5th European-American workshop on reliability of NDE N2 - POD is the most often used approach for the evaluation of the reliability of non-destructive testing methods in critical areas. But especially for those cases the requirements for a sufficient amount of data, adequate type of defects and the statistical requirements are high. The claim for checking these requirements is not new, but never the less often ignored. Especially the large amount of data for critical real defects seems too often to be not really solvable. In this presentation we show an approach to use real defect data with knowledge from former testing results with the same equipment, in a useful adequate way. Furthermore we introduce a method to evaluate the real defect description parameters for the radiographic testing. This approach was used for a joint project with the company POSIVA, which is building a final depository for spent nuclear fuel in Finland. Radiographic testing is one of the NDT-methods they use to test the electron beam weld of the copper canister. The copper canister will be used in the deposit as a corrosion barrier within the deposit concept. Through the high sophisticated manufacturing methods of the canister there are almost no material defects, which could be used for reliability evaluation. In this context the idea of Bayesian Updating of the POD with real defect data with former results from artificial defect data was born to get a useful evaluation. T2 - 5th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 07.10.2013 PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-312641 SN - 978-3-940283-53-5 IS - DGZfP-BB 144 SP - Lecture 4, 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-31264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. T1 - Probability of defect detection of Posiva's electron beam weld T2 - Working Report 2013-70 N2 - The report 'Probability of Defect Detection of Posiva's electron beam weld' describes POD curves of four NDT methods radiographic testing, ultrasonic testing, eddy current testing and visual testing. POD-curves are based on the artificial defects in reference blocks. The results are devoted to the demonstration of suitability of the methods for EB weld testing. Report describes methodology and procedure applied by BAM. Report creates a link from the assessment of the reliability and inspection performance to the risk assessment process of the canister final disposal project. Report ensures the confirmation of the basic quality of the NDT methods and their capability to describe the quality of the EB-weld. The probability of detection curves are determined based on the MIL-1823 standard and it's reliability guidelines. The MIL-1823 standard was developed for the determination of integrity of gas turbine engines for the US military. In the POD-process there are determined as a key parameter for the defect detectability the a90/95 magnitudes, i.e. the size measure a of the defect, for which the lower 95 % confidence band crosses the 90 % POD level. By this way can be confirmed that defects with a size of a90/95 will be detected with 90 % probability. In case the experiment will be repeated 5 % might fall outside this confidence limit. KW - Probability of detection curves KW - POD-curves KW - NDT-methods KW - EB-welding KW - Ultrasonic inspection KW - Radiographic inspection KW - Eddy current inspection KW - Visual inspection PY - 2013 UR - http://www.posiva.fi/en/databank/working_reports/probability_of_defect_detection_of_posiva_s_electron_beam_weld.1874.xhtml?xm_col_report_year=2013&xm_col_language=3&xm_col_type=5&cd_order=col_report_number&cd_offset=0#.VJAIY3uj_mc UR - http://www.posiva.fi/files/3527/WR_2013-70.pdf SP - 1 EP - 86 AN - OPUS4-32512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. A1 - Ewert, Uwe T1 - Bayesian approach for the evaluation of the reliability of non-destructive testing methods: combination of data from artificial and real defects T2 - 18th WCNDT - World conference on nondestructive testing (Proceedings) N2 - The Probability of Detection (POD) is used to evaluate the detectability of non-destructive testing (NDT) systems. The POD is highly dependent on the amount of available data. The Bayesian approach provides a solution to compute POD-curves in case of a small amount of real defects without losing the necessary information. The result contains the needed information for the computation of POD-curves for real defects with an acceptable amount of information, even for sparse amount of data. In this paper is shown limitations of the Bayesian approach and how it can be applied to NDT. The Bayesian approach is applied in this case to the evaluation of radiographic testing. Bayesian approach is applied to determine POD-curves for the inspection techniques of nuclear fuel disposal canisters. The reason for using Bayesian approach is the high safety demands and also the low amount of real defects due to the high quality of the reliable production techniques. T2 - 18th WCNDT - World conference on nondestructive testing CY - Durban, South Africa DA - 2012-04-16 KW - Reliability KW - Probability of Detection KW - Real defect testing KW - Bayesian statistics KW - Radiographic testing PY - 2012 SN - 978-0-620-52872-6 SP - 1 EP - 6 (Paper 196) AN - OPUS4-27582 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Schafer, Lloyd T1 - Current Status in the Areas of Reliability of NDT: Experience in Europe and USA T2 - ASNT Spring Conference and 11th Annual Research Symposium 2002, "Experience the Power of NDE/NDT" T2 - ASNT Spring Conference and 11th Annual Research Symposium 2002, "Experience the Power of NDE/NDT" CY - Portland, OR, USA DA - 2002-03-18 PY - 2002 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-2008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina T1 - Mine Detector Test Trials in Afghanistan JF - Materials evaluation PY - 2002 SN - 0025-5327 VL - 60 IS - 10 SP - 1223 EP - 1225 PB - Society for Nondestructive Testing CY - Columbus, Ohio AN - OPUS4-2023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina T1 - Minendetektor-Tests in Afghanistan JF - DGZfP-Zeitung PY - 2002 SN - 0948-5112 VL - 80 SP - 41 EP - 42 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung CY - Berlin AN - OPUS4-2012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - 3rd European-American Workshop on Reliability of NDE and Demining T2 - Proceedings of the NDRF Summer Conference T2 - NDRF Summer Conference 2002 CY - Rosersberg, Sweden DA - 2002-08-28 PY - 2002 SP - 1(?) AN - OPUS4-2014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Proposals for Performance Demonstration and Modular Validation T2 - 3rd DTIF workshop T2 - 3rd DTIF workshop CY - Ispra, Italy DA - 2002-09-23 PY - 2002 SP - 1 EP - 8 AN - OPUS4-2019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Gaal, Mate A1 - Guelle, D. A1 - Lewis, A. A1 - Sieber, A. T1 - Proposals for Performance Demonstration and Modular Reliability Assessment for Humanitarian Demining T2 - EUDEM2-SCOT - 2003, Vrije Universiteit Brussel T2 - EUDEM2-SCOT - 2003, Vrije Universiteit Brussel CY - Brussels, Belgium DA - 2003-09-15 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-3077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Fücsök, F. T1 - Some Results of the RRT of the Radiographic Film Evaluation T2 - MATEST 2003, NDT - Achievments & Challenges, HDKBR / CrSNDT T2 - MATEST 2003, NDT - Achievments & Challenges, HDKBR / CrSNDT CY - Brijuni, Croatia DA - 2003-09-28 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-3081 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Smith, A. T1 - Accidents and Incidents in Humanitarian Demining (HD) - the Need to Keep Accurate Records for Meaningful Analysis T2 - European-American Workshop 2002 T2 - European-American Workshop 2002 CY - Berlin, Germany DA - 2002-09-11 PY - 2002 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-3264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - 3rd European-American Workshop on Reliability of NDE and Demining T2 - NDRF Summer Conference 2002 T2 - NDRF Summer Conference 2002 CY - Rosersberg, Sweden DA - 2002-08-28 PY - 2002 AN - OPUS4-3276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Proposals for Statistical Methods for Evaluating Performance T2 - CEN Workshop 7 T2 - CEN Workshop 7 “Humanitarian Mine Action - Test and Evaluation - Metal Detectors” (CW07) CY - Ispra, Italy DA - 2002-04-08 PY - 2002 VL - 7 SP - 1 EP - 7 AN - OPUS4-2067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Schafer, Lloyd A1 - Völker, J. A1 - Wilrich, P.-Th. T1 - Concepts in Reliability Measurement T2 - European-American Workshop 2002 T2 - European-American Workshop 2002 CY - Berlin, Germany DA - 2002-09-11 PY - 2002 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-3557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Schafer, Lloyd A1 - Völker, J. T1 - Das Basisanliegen von Zuverlässigkeitsuntersuchungen und eine Momentaufnahme im internationalen Geschehen T2 - DGZfP-Jahrestagung 2002: ZfP in Anwendung, Entwicklung und Forschung T2 - DGZfP-Jahrestagung 2002: ZfP in Anwendung, Entwicklung und Forschung CY - Weimar, Germany DA - 2002-05-06 PY - 2002 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-3581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Gaal, Mate A1 - Guelle, D. A1 - Lewis, A. A1 - Sieber, A. T1 - Proposals for perfomance demonstration and modular reliability assessment for humanitarian demining T2 - EUDEM2-SCOT - 2003 T2 - EUDEM2-SCOT - 2003 CY - Brussels, Belgium DA - 2003-09-15 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-4461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Völker, J. T1 - Konzepte zur Quantifizierung des Restrisikos bei der Minensuche und in der zerstörungsfreien Prüfung T2 - DGZfP-Jahrestagung 2003: Zerstörungsfreie Materialprüfung - ZfP in Anwendung, Entwicklung und Forschung T2 - DGZfP-Jahrestagung 2003: Zerstörungsfreie Materialprüfung - ZfP in Anwendung, Entwicklung und Forschung CY - Mainz, Germany DA - 2003-05-26 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-4462 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bär, Sylke A1 - Wilrich, P.-Th. T1 - Proposals for Perfomance Demonstration and Modular Validation T2 - 5th Meeting of CEN/BT/WG 126 T2 - 5th Meeting of CEN/BT/WG 126 CY - Copenhagen, Denmark DA - 2003-01-22 PY - 2003 AN - OPUS4-4463 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Guelle, D. A1 - Lewis, A. A1 - Sieber, A. A1 - Böttger, U. T1 - Proposals for perfomance demonstration and modular reliability assessment for humanitarian demining T2 - CEN WS 12 Meeting T2 - CEN WS 12 Meeting CY - Sibenik, Croatia DA - 2003-10-14 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-4465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Wilrich, P.-Th. A1 - Gaal, Mate T1 - Acceptance Tests T2 - CEN WS 12 Meeting T2 - CEN WS 12 Meeting CY - Sibenik, Croatia DA - 2003-10-14 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-4466 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Landminen - sicheres Aufspüren einer unsichtbaren Bedrohung? Teil 1: Probleme der Zuverlässigkeit bei der Minensuche T2 - BAM-Vortragsreihe zum Tag der offenen Tür T2 - BAM-Vortragsreihe zum Tag der offenen Tür CY - Berlin, Germany DA - 2004-03-05 PY - 2004 AN - OPUS4-5581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Bär, Sylke A1 - Lewis, A. A1 - Bloodworth, T. A1 - Guelle, D. A1 - Wilrich, P.-Th. T1 - Optimizing detector trials for humanitarian demining T2 - International Symposium "Humanitarian Demining 2004 T2 - International Symposium "Humanitarian Demining 2004 CY - Sibenik, Croatia DA - 2004-04-21 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5582 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ewert, Uwe A1 - Gaal, Mate A1 - Osterloh, Kurt A1 - Rosenthal, Martina T1 - Determination of the Reliability of Sensors for Security T2 - Workshop "Sensors for Security", Joint Research Centre (JRC) T2 - Workshop "Sensors for Security", Joint Research Centre (JRC) CY - Ispra, Italy DA - 2004-06-14 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Osterloh, Kurt A1 - Wilrich, P.-Th. T1 - Determination of the Reliability of Sensors for Security T2 - Eurosensors XVIII T2 - Eurosensors XVIII CY - Rome, Italy DA - 2004-09-13 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina T1 - Measuring Demining Performance in a Modular Model and Field Tests T2 - EUDEM2 Final Workshop: Is Humanitarian Demining Technology a Broken Promise? T2 - EUDEM2 Final Workshop: Is Humanitarian Demining Technology a Broken Promise? CY - Brussels, Belgium DA - 2004-10-05 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Elagin, Mstislav A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Osterloh, Kurt A1 - Wilrich, P.-Th. T1 - Determination of Reliability in Demining and NDT T2 - MATEST 2004; NDT - Competence & Safety T2 - MATEST 2004; NDT - Competence & Safety CY - Zagreb, Croatia DA - 2004-10-14 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Bär, Sylke A1 - Osterloh, Kurt A1 - Böllinghaus, Thomas A1 - Ewert, Uwe A1 - Guelle, D. A1 - Bloodworth, T. A1 - Lewis, A. A1 - Pavkovic, N. A1 - Steker, I. A1 - Wilrich, P.-Th. T1 - Landminen - Wie sicher kann man die unsichtbare Bedrohung aufspüren? T2 - DGZfP-Arbeitskreis T2 - DGZfP-Arbeitskreis CY - Frankfurt am Main, Germany DA - 2004-10-27 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ryden, H. A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Ronneteg, U. A1 - Rosenthal, Martina T1 - Reliability Evaluation of NDT Techniques for Cu-Welds for Risk Assessment of Nuclear Waste Encapsulation T2 - 4th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurised Components T2 - 4th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurised Components CY - London, England DA - 2004-12-06 PY - 2004 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-5588 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Bär, Sylke A1 - Osterloh, Kurt A1 - Böllinghaus, Thomas A1 - Ewert, Uwe A1 - Guelle, D. A1 - Bloodworth, T. T1 - Testverfahren für Sondiertechnik erläutert am Beispiel: Zuverlässigkeit in der Minensuche T2 - 6. Fachtagung Kampfmittelbeseitigung T2 - 6. Fachtagung Kampfmittelbeseitigung CY - Dresden, Germany DA - 2005-03-09 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Redmer, Bernhard A1 - Rosenthal, Martina A1 - Ryden, H. A1 - Ronneteg, U. T1 - Reliability Evaluation of NDT Techniques for Cu-Welds for Risk Assessment of Nuclear Waste Ecapsulation T2 - 31st MPA-Seminar "Materials & Components Behaviour in Energy & Plant Technology" T2 - 31st MPA-Seminar "Materials & Components Behaviour in Energy & Plant Technology" CY - Stuttgart, Germany DA - 2005-10-13 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11377 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Wilrich, P.-Th. T1 - Special Topic: Determination of the Reliability of Sensors for Security T2 - Visit at REASero T2 - Visit at REASero CY - Riel, Netherlands DA - 2005-06-27 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Ewert, Uwe T1 - Das Anliegen der BAM-ITEP-Testversuche; Ergebnisse von 2003 und Zielsetzung 2005 in Richtung realistischer feldnaher und belastbarer Tests für Metalldetektoren T2 - BAM-BMVg Seminar T2 - BAM-BMVg Seminar CY - Berlin, Germany DA - 2005-04-21 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11379 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Ryden, H. A1 - Ronneteg, U. T1 - Reliability Evaluation of NDT Techniques for Cu-Welds forRisk Assessment of Nuclear Waste Encapsulation T2 - Advances in Signal Processing for Non Destructive Evaluation of Materials 4th International Workshop T2 - Advances in Signal Processing for Non Destructive Evaluation of Materials 4th International Workshop CY - Quebec City, Canada DA - 2005-08-02 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Wilrich, P.-Th. T1 - Reliability Tests for Demining T2 - Advances in Signal Processing for Non Destructiv Evaluation of Materials 4th International Workshop T2 - Advances in Signal Processing for Non Destructiv Evaluation of Materials 4th International Workshop CY - Quebec City, Canada DA - 2005-08-02 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina T1 - Einflussfaktoren auf die Zuverlässigkeit und das Restrisiko bei der Minensuche T2 - AK Risiko, BAM T2 - AK Risiko, BAM CY - Berlin, Germany DA - 2005-09-30 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11394 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Wilrich, P.-Th. T1 - Reliability Tests for Demining T2 - International Symposium 2005: Use and Testing of Demining Machines T2 - International Symposium 2005: Use and Testing of Demining Machines CY - Sibenik, Croatia DA - 2005-04-25 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Wilrich, P.-Th. T1 - Reliability Tests for Demining T2 - International Symposium 2005: Use and Testing of Demining Machines T2 - International Symposium 2005: Use and Testing of Demining Machines CY - Sibenik, Croatia DA - 2005-04-25 PY - 2005 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-11391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina T1 - 5. Europäisch-Amerikanischer Workshop über Zuverlässigkeit der ZfP T2 - DGZfP-Jahrestagung T2 - DGZfP-Jahrestagung CY - Dresden, Germany DA - 2013-05-06 PY - 2013 AN - OPUS4-28634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Skender, Marina A1 - Rosenthal, Martina A1 - Pitkänen, J. T1 - Holistische Betrachtung der Zuverlässigkeit von industriellen ZfP-Systemen; Können wir wirklich die Zuverlässigkeit vor Ort voraussagen? - von der Labor-POD zu den aktuellen Bedingungen vor Ort T2 - DGZfP-Jahrestagung T2 - DGZfP-Jahrestagung CY - Dresden, Germany DA - 2013-05-06 PY - 2013 AN - OPUS4-28635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bellon, Carsten A1 - Elagin, Mstislav A1 - Redmer, Bernhard A1 - Rosenthal, Martina A1 - Zscherpel, Uwe A1 - Ronneteg, U. A1 - Ryden, H. T1 - POD (Probability of Detection) evaluation of NDT techniques for Cu-Welds for risk assessment of nuclear waste encapsulation T2 - 4th International Probabilistic Symposium T2 - 4th International Probabilistic Symposium CY - Berlin, Germany DA - 2006-10-12 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bellon, Carsten A1 - Elagin, Mstislav A1 - Ewert, Uwe A1 - Redmer, Bernhard A1 - Rosenthal, Martina A1 - Zscherpel, Uwe A1 - Ronneteg, U. A1 - Ryden, H. T1 - POD (Probability of Detection) evaluation of NDT techniques for Cu-Canisters for risk assessment of nuclear waste encapsulation T2 - ECNDT 2006 9. Europäische Konferenz für Zerstörungsfreie Prüfung T2 - ECNDT 2006 9. Europäische Konferenz für Zerstörungsfreie Prüfung CY - Berlin, Germany DA - 2006-09-25 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ryden, H. A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Ronneteg, U. A1 - Rosenthal, Martina T1 - Concept for determination of the reliability of NDT and results from the study T2 - Seminar NDT Reliability SKB Headquaters T2 - Seminar NDT Reliability SKB Headquaters CY - Stockholm, Sweden DA - 2006-01-09 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14314 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Ryden, H. A1 - Ronneteg, U. T1 - POD evaluation of digital radiography of Cu-welds embedded in a general risk assessment study for nuclear waste deposit T2 - Filmfree Meeting, BAM Berlin T2 - Filmfree Meeting, BAM Berlin CY - Berlin, Germany DA - 2006-01-05 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ryden, H. A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Ronneteg, U. A1 - Rosenthal, Martina T1 - POD evaluation of NDT techniques for CU-canisters for risk assessment of nuclear waste encapsulation T2 - 5th International Conference on NDE in Relation to Structural Intergrity for Nuclear and Pressurized Components T2 - 5th International Conference on NDE in Relation to Structural Intergrity for Nuclear and Pressurized Components CY - San Diego, CA, USA DA - 2006-05-10 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Gaal, Mate A1 - Pavlovic, Mato T1 - Reliability tests for demining -latest experiences- T2 - Humanitarian Demining 2006 - " Mine and Uxo Detection", International Symposium Sibenik T2 - Humanitarian Demining 2006 - " Mine and Uxo Detection", International Symposium Sibenik CY - Sibenik, Croatia DA - 2006-04-24 PY - 2006 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14319 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ewert, Uwe A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Ronneteg, U. A1 - Rydén, H. T1 - Zuverlässigkeit von ZfP-Verfahren zur Gewährleistung der Integrität von Cu-Schweißnähten zur sicheren Endlagerung radioaktiver Abfälle T2 - DGZfP-Jahrestagung (ZfP in Forschung, Entwicklung und Anwendung) T2 - DGZfP-Jahrestagung (ZfP in Forschung, Entwicklung und Anwendung) CY - Fürth, Germany DA - 2007-05-14 PY - 2007 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-14826 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Reliability for security - offer to complete your project T2 - Europäische -Sicherheitsforschungskonferenz SRC ´07 T2 - Europäische -Sicherheitsforschungskonferenz SRC ´07 CY - Berlin, Germany DA - 2007-03-26 PY - 2007 AN - OPUS4-14836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Takahashi, K. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Evaluation of Inspection Reliability T2 - NDT-Days 2010 T2 - NDT-Days 2010 CY - Tallinn, Estonia DA - 2010-03-17 PY - 2010 AN - OPUS4-22703 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Rosenthal, Martina A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Progress in Evaluating the Reliability of NDE Systems - Paradigm Shift T2 - 8th International Conference on NDE in Relation to Structural Integrity of Nuclear an Pressurised Components N2 - The paper will give an overview of new methodology for evaluating the reliability of NDE systems accurately, reliably and efficiently in accordance with the specific requirements of industrial application. After a review of the substantive issues from the status in 2002, the go forward guidance from these interactions is considered. At the beginning of the reliability analysis, the actual safety demands have to be defined in order to fit the investigation to the level of risk when the component would fail. Next, all the essential influencing parameters need to be documented and transferred to an appropriate design of experiments (DOE) to determine the reliability in terms of a qualitative assessment for lower risk or in terms of a quantitative probability of detection (POD) or ROC (Receiver Operating Characteristics) curves for higher safety demands. A new paradigm is offered to consider the POD or reliability of the system as a function of the configuration of input variables and use it for optimisation rather than for a final judgement. An advantage for the end user is also to sample all single PODs to an integral “Volume POD” of a part. Among the influencing parameters, the human factor is the most important one. A systematic psychological approach shall help to find out where the bottlenecks are but most importantly to provide best possible working conditions for the human inspectors. T2 - 8th International Conference on NDE in Relation to Structural Integrity of Nuclear an Pressurised Components CY - Berlin, Germany DA - 2010-09-29 PY - 2010 UR - http://www.ndt.net/article/jrc-nde2010/papers/34.pdf AN - OPUS4-22508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Ewert, Uwe A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - The Holistic View on the Reliability of NDE Systems - Paradigm Shift T2 - 9th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components T2 - 9th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components CY - Seattle, WA, USA DA - 2012-05-22 PY - 2012 AN - OPUS4-27004 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Ewert, Uwe A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Holistically Evaluating the Reliability of NDE Systems - Paradigm Shift T2 - 18th World Conference on Non Destructive Testing T2 - 18th World Conference on Non Destructive Testing CY - Durban, South Africa DA - 2012-04-16 PY - 2012 AN - OPUS4-27005 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Dobberphul, Tobias A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Rosenthal, Martina A1 - Holstein, R. A1 - Ronneteg, U. A1 - Pitkänen, J. T1 - Plenary View on the Vigor of our NDE Reliability Models T2 - 5th European-American Workshop on Reliability of NDE T2 - 5th European-American Workshop on Reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 AN - OPUS4-31210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ronneteg, U. A1 - Pitkänen, J. A1 - Fahlbruch, B. T1 - Holistic risk assessment and risk prevention approach to the mechanized NDT and the inspection procedure T2 - 5th European-American Workshop on Reliability of NDE T2 - 5th European-American Workshop on Reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 AN - OPUS4-31211 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Ronneteg, U. A1 - Pitkänen, J. A1 - Fahlbruch, B. T1 - Holistic risk assessment and risk prevention approach to the mechanized NDT and the inspection procedure T2 - 10th International Conference on Non Destructive Evaluation in relation to structural Integrity for nuclear an pressurized components T2 - 10th International Conference on Non Destructive Evaluation in relation to structural Integrity for nuclear an pressurized components CY - Cannes, France DA - 2013-10-01 PY - 2013 AN - OPUS4-31212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pitkänen, J. T1 - Evaluation of RT Systems with an Observer-POD T2 - 5th European-American Workshop on Reliability of NDE T2 - 5th European-American Workshop on Reliability of NDE CY - Berlin, Germany DA - 2013-10-07 PY - 2013 AN - OPUS4-31217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Redmer, Bernhard A1 - Ewert, Uwe A1 - Schaefer, L. T1 - Modulare Analyse der Zuverlässigkeit von ZfP-Systemen mit dem Werkzeug der Systemtheorie - Eine gute Balance zwischen Sicherheit und Ökonomie T2 - DGZfP-JAHRESTAGUNG 2002 N2 - Untersucht wird die Modulare Validierung, die Mechanisierte Durchstrahlungsprüfung und die Wirbelstromprüfung an hoch beanspruchten Teilen aus der Luftfahrt. T2 - DGZfP-JAHRESTAGUNG 2002 CY - Weimar, Germany DA - 06.05.2002 PY - 2002 AN - OPUS4-19972 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Finke, Robert A1 - Milsch, Steffen T1 - Fehlerauffindwahrscheinlichkeit zerstörungsfreier Prüfungen T2 - IMQ T2 - IMQ CY - Crimmitschau, Germany DA - 2010-04-22 PY - 2010 AN - OPUS4-22505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Zuverlässigkeit zerstörungsfreier Prüfungen T2 - Zuverlässigkeit zerstörungsfreier Prüfungen T2 - Zuverlässigkeit zerstörungsfreier Prüfungen CY - Berlin, Germany DA - 2010-05-17 PY - 2010 AN - OPUS4-22426 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Heidt, Heinrich A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Takahashi, Kazunori A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Fortschritte bei der Bewertung der Zuverlässigkeit von ZfP-Systemen T2 - DGZfP Jahrestagung 2009 T2 - DGZfP Jahrestagung 2009 CY - Münster, Germany DA - 2009-05-18 PY - 2009 AN - OPUS4-20547 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Heidt, Heinrich A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Takahashi, Kazunori A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Progress in Evaluating the Reliability of NDE Systems - Paradigm Shift T2 - 4th European-American Workshop on Reliability of NDE T2 - 4th European-American Workshop on Reliability of NDE CY - Berlin, Germany DA - 2009-06-24 PY - 2009 AN - OPUS4-20543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Bartsch, Ludwig A1 - Rosenthal, Martina A1 - Jaenisch, Gerd-Rüdiger A1 - Holstein, R. T1 - Analysis and synthesis of NDT reliability using the extended modular model N2 - The aim of all the effort devoted to NDE reliability is to evaluate the reliability accurately, reliably and efficiently, in accordance with the specific requirements of industrial application taking into account the very different nature of influencing factors. The set up of the Modular Reliability Model in 1997 was a big step forward in the understanding of influencing mechanisms in terms of the three different main elements, i.e. the intrinsic capability (IC), the application parameters (AP) and the human factors (HF). The intrinsic capability stands for the pure physical-technological process of the signal detection caused by the waves or the rays from a material defect in the presence of noise (caused by the material and the devices). This intrinsic capability is the upper bound of the possible reliability. Already when measuring this intrinsic capability for thick walled components the original one-parameter POD should be extended to a multi-parameter POD, where, in addition to the defect size, a number of additional physical parameters, such as the grain size distribution (or attenuation), defect depth, and angle or surface roughness, must be considered. For real life cycle assessments it is necessary to evaluate the signal response from real defects. The industrial application factors, e.g. coupling conditions, limited accessibility, heat and environmental vibrations, diminish the reliability. The amount of reduction can be determined quantitatively, if the underlying conditions are controlled. In case they are not controlled it is necessary to count for a (unknown) fluctuation in the reliability in the field anyway. The third group of important influencing factors are the human factors, which do not only cover the individual performance capability of the inspectors but also the design of the working place, the procedure, the teamwork quality, interaction with systems, the organization, and finally, the relationship between the companies involved in the inspection process and to which extend the responsible parties are aware of it. Both the internal and external organizational context, affect not only the HF but also the IC and AP. After having analysed the single factors separately it is necessary to look how everything is interconnected. When comparing an “ideal inspection” with a “real inspection” it is worthwhile to look at the existing practices, rules and standards. How do they really support reliable testing? With respect to the industrial end user, it needs to be shown how the level of reliability of NDE, influenced by the different factors and their interaction, has an impact on acceptance or rejection of safety critical parts. The approach of analysis and synthesis will be illustrated by examples of the reliability investigation of the inspection of copper canisters for nuclear fuel deposit in Sweden and Finland and German Railway inspections (hollow axle testing). T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - Modular model PY - 2016 AN - OPUS4-37602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Ronneteg, U. T1 - New challenges for the quantification of the NDT reliability T2 - 6th European-American Workshop on Reliability of NDE T2 - 6th European-American Workshop on Reliability of NDE CY - Minneapolis, USA DA - 2015-07-26 PY - 2015 AN - OPUS4-34591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Kanzler, Daniel A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Bertovic, Marija A1 - Holstein, R. A1 - Gianneo, A. A1 - Ronneteg, U. T1 - Holistic Assessment of the Reliability of NDE T2 - 6th European-American Workshop on Reliability of NDE T2 - 6th European-American Workshop on Reliability of NDE CY - Minneapolis, USA DA - 2015-07-26 PY - 2015 AN - OPUS4-34594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Ronneteg, U. T1 - Können unsere Prüfanweisungen besser sein? T2 - DACH Jahrestagung 2015 T2 - DACH Jahrestagung 2015 CY - Salzburg, Austria DA - 2015-05-11 PY - 2015 AN - OPUS4-33722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Kanzler, Daniel A1 - Pavlovic, Mato A1 - Bertovic, Marija A1 - Holstein, R. T1 - Ganzheitliche Betrachtung der Zuverlässigkeit von industriellen ZfP-Systemen - können wir wirklich die Zuverlässigkeit vor Ort voraussagen? T2 - DACH Jahrestagung 2015 T2 - DACH Jahrestagung 2015 CY - Salzburg, Austria DA - 2015-05-11 PY - 2015 AN - OPUS4-33724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Christina A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Heidt, Heinrich A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Takahashi, K. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Progress in evaluating the reliability of NDE systems - Paradigm shift T2 - 4th European-American workshop on reliability of NDE / DGZfP-Proceedings N2 - The paper will give an overview of new methodology for evaluating the reliability of NDE systems accurately, reliably and efficiently in accordance with the specific requirements of industrial application. After a review of the substantive issues from the previous workshops, the go forward guidance from these interactions is considered. At the beginning of the reliability analysis, the actual safety demands have to be defined in order to fit the investigation to the level of risk when the component would fail. Next, all the essential influencing parameters need to be documented and transferred to an appropriate design of experiments (DOE) to determine the reliability in terms of a qualitative assessment for lower risk or in terms of a quantitative probability of detection (POD) or ROC (Receiver Operating Characteristics) curves for higher safety demands. A new paradigm is offered to consider the POD or reliability of the system as a function of the configuration of input variables and use it for optimisation rather than for a final judgement. An advantage for the end user is also to sample all single PODs to an integral 'Volume POD' of a part. Among the influencing parameters, the human factor is the most important one. A systematic psychological approach shall help to find out where the bottlenecks are but most importantly to provide best possible working conditions for the human inspectors. T2 - 4th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2009-06-24 KW - Zuverlässigkeit von ZfP-Systemen KW - Multiparameter POD PY - 2009 UR - http://www.ndt.net/article/reliability2009/Inhalt/we1a2.pdf SN - 978-3-940283-17-7 IS - DGZfP-BB 116 SP - 1 EP - 13 AN - OPUS4-20616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Holstein, R. A1 - Kanzler, Daniel A1 - Pitkänen, J. A1 - Ronneteg, U. A1 - Heckel, Thomas T1 - A plenary view on the vigour of our NDE reliability models T2 - 5th European-American workshop on reliability of NDE N2 - Using the Modular Reliability Model the three different main influencing elements, i.e. intrinsic capability (IC), application parameters (AP) and the human factors (HF), are, in the first instance, investigated separately. The intrinsic capability stands for the pure physical-technological process of the signal detection caused by the waves or the rays from a material defect in the presence of noise (driven by the material and the devices). This intrinsic capability is the upper bound of the possible reliability. Already when measuring this intrinsic capability for thick walled components the original one-parameter POD must be extended to a multiparameter POD, where, in addition to the defect size, a number of additional physical parameters, such as the grain size distribution (or attenuation), defect depth, and angle or surface roughness, must be considered. For real life cycle assessments it is necessary to evaluate the signal response from real defects. The industrial application factors, e.g. coupling conditions, limited accessibility, heat and environmental vibrations, diminish the reliability. The amount of reduction can be determined quantitatively, if the underlying conditions are controlled. In case they are not controlled it is necessary to count for a fluctuation in the reliability in the field anyway. The third group of important influencing factors are the human factors, which do not only cover the individual performance capability of the inspectors but also the design of the working place,the procedure, the teamwork quality, interaction with systems, the organization, and finally, the relationship between the companies involved in the inspection process and to which extend the responsible parties are aware of it. When comparing an “ideal inspection” with a “real inspection” it is worth while to look how the existing practices, rules and standards support reliable testing and where the “delta” is. In the context of vigor, with respect to the industrial end user, it needs to be shown how the level of reliability of NDE, influenced by the different factors, has an impact on acceptance or rejection of safety critical parts. T2 - 5th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 07.10.2013 PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-312658 SN - 978-3-940283-53-5 IS - DGZfP-BB 144 SP - Lecture 2, 1 EP - 18 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-31265 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Ronneteg, U. T1 - Conclusions of the 6th European American workshop on reliability of NDE JF - AIP Conference Proceedings N2 - The principles of Open Space Technology (OST) were again applied to discuss burning issues in the field of NDE reliability. The results of the discussions among NDE professionals concerning new reliability methods, human factors and integrated solutions will be presented. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.20155 KW - NDT KW - Reliability KW - Probability of detection KW - Human factors KW - POD PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940452 SN - 0094-243X VL - 1706 SP - 020006-1 EP - 020006-9 PB - AIP Publishing AN - OPUS4-36637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Ewert, Uwe A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Paradigm shift in the holistic evaluation of the reliability of NDE systems JF - Materials Testing N2 - Das Ziel des Artikels ist es eine Übersicht über neue methodische Ansätze und Verfahren zur Bewertung der Zuverlässigkeit von ZfP-Systemen in Übereinstimmung mit den spezifischen Anforderungen verschiedener industrieller Anwendungen zu geben. Nach einem Überblick über die in den vergangenen Jahrzehnten erreichten Fortschritte, wird der Fokus auf die gegenwärtigen Entwicklungen gerichtet. Für hohe Sicherheitsanforderungen wurde die quantitative Fehlerauffindwahrscheinlichkeit (probability of detection, POD) basierend auf 'hit/miss'- oder 'Signal-Response'-Analysen und die ROC-Analyse (Receiver Operating Characteristics) als typische Werkzeuge entwickelt. Im Rahmen des modularen Modells für die ZfP-Zuverlässigkeit unterscheidet man zwischen den rein physikalisch-technischen Einflussfaktoren, den industriellen Anwendungsfaktoren und den menschlichen Faktoren. Es hilft zum Beispiel zu erkennen, welche dieser Faktoren man in Modellierungsrechnungen bzw. mittels offenen oder Blindversuchen untersuchen kann. Ein neues Paradigma wird für die Betrachtung der POD als eine Funktion der gewählten Systemparameter und somit als Optimierungswerkzeug verwendet, anstelle sie für die endgültige Beurteilung zu nehmen. Zur Handhabung der Zuverlässigkeitsuntersuchung von realen Defekten in einer realistischen Umgebung werden ökonomisch vertretbare, aber dennoch präzise genug arbeitende Methoden, wie der Ansatz von Bayes oder modellbasierte Methoden vorgestellt. Die menschlichen Faktoren sind oft von ausschlaggebender Wichtigkeit für die Gesamtzuverlässigkeit. Hier hilft ein systematischer psychologischer Ansatz die Engpässe und Verbesserungsmöglichkeiten zu finden. KW - Zuverlässigkeit KW - Modulares Modell KW - POD KW - Human factors PY - 2013 DO - https://doi.org/10.3139/120.110433 SN - 0025-5300 VL - 55 IS - 4 SP - 261 EP - 269 PB - Hanser CY - München AN - OPUS4-28831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Ewert, Uwe A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Holistically evaluating the reliability of NDE systems - paradigm shift T2 - 18th WCNDT - World conference on nondestructive testing (Proceedings) N2 - New methodologies for evaluating the reliability of NDE systems are discussed in accordance with the specific requirements of industrial application. After a review of the substantive issues from the previous decades, the go forward guidance is concluded. For high safety demands a quantitative probability of detection (POD) created from hit miss experiments or signal response analysis and ROC (Receiver Operating Characteristics) are typically created. The modular model distinguishes between the influence of pure physics and technique, industrial application factors and the human factor and helps to learn what factors are covered by modelling, open or blind trials. A new paradigm is offered to consider the POD or reliability of the system as a function of the configuration of input variables and use it for optimisation rather than for a final judgement. New approaches are considered dealing with real defects in a realistic environment, affordable but precisely like the Bayesian approach or model assisted methods. Among the influencing parameters, the human factor is of high importance. A systematic psychological approach helps to find out where the bottlenecks are and shows possibilities for improvement. T2 - 18th WCNDT - World conference on nondestructive testing CY - Durban, South Africa DA - 2012-04-16 KW - Reliability of NDE KW - POD KW - ROC KW - Modular Model KW - Multiparameter-POD KW - Bayesian Approach KW - Human Factor PY - 2012 SN - 978-0-620-52872-6 SP - 1 EP - 14 (Paper 591) AN - OPUS4-27579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Bertovic, Marija A1 - Pavlovic, Mato A1 - Kanzler, Daniel A1 - Rosenthal, Martina A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Progress in evaluating the reliability of NDE systems - paradigm shift T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components (DGZfP-Proceedings) N2 - The paper will give an overview of new methodology for evaluating the reliability of NDE systems accurately, reliably and efficiently in accordance with the specific requirements of industrial application. After a review of the substantive issues from the previous workshops, the go forward guidance from these interactions is considered. At the beginning of the reliability analysis, the actual safety demands have to be defined in order to fit the investigation to the level of risk when the component would fail. Next, all the essential influencing parameters need to be documented and transferred to an appropriate design of experiments (DOE) to determine the reliability in terms of a qualitative assessment for lower risk or in terms of a quantitative probability of detection (POD) or ROC (Receiver Operating Characteristics) curves for higher safety demands. A new paradigm is offered to consider the POD or reliability of the system as a function of the configuration of input variables and use it for optimisation rather than for a final judgement. An advantage for the end user is also to sample all single PODs to an integral 'Volume POD' of a part. Among the influencing parameters, the human factor is the most important one. A systematic psychological approach shall help to find out where the bottlenecks are but most importantly to provide best possible working conditions for the human inspectors. T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components CY - Berlin, Germany DA - 2010-09-29 KW - Reliability KW - POD KW - ROC KW - Safety PY - 2010 SN - 978-3-940283-30-6 IS - DGZfP-BB 125 (Th.3.A.4) SP - 1 EP - 10 CY - Berlin AN - OPUS4-23923 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Rosenthal, Martina A1 - Redmer, Bernhard A1 - Ryden, H. A1 - Ronneteg, U. T1 - Reliability evaluation of NDT techniques for Cu-welds for risk assessment of nuclear waste encapsulation JF - Materialprüfung = Materials testing KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - POD KW - Endlagerung radioaktiver Abfälle PY - 2006 SN - 0025-5300 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. VL - 48 IS - 3 SP - 111 EP - 117 PB - Carl Hanser Verlag CY - München AN - OPUS4-14421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Christina A1 - Elagin, Mstislav A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Rosenthal, Martina A1 - Redmer, Bernhard A1 - Ryden, H. A1 - Ronneteg, U. ED - Proske, D. T1 - Probability-of-Detection-Evaluation of NDT Techniques for Cu-Canisters for Risk Assessment of Nuclear Waste Encapsulation T2 - 4th International Probabilistic Symposium : 12th - 13th October 2006 T2 - 4th International Probabilistic Symposium CY - Berlin, Germany DA - 2006-10-12 KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - POD KW - Endlagerung radioaktiver Abfälle PY - 2006 SN - 3-00-019232-8 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 227 EP - 252 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-14418 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -