TY - CONF A1 - Goedecke, Caroline T1 - Detection of polymers in treated waste water using TED-GC-MS N2 - The presence of large quantities of plastic waste and its fragmentation in various environmental compartments are an important subject of current research. In the environment, (photo ) oxidation processes and mechanical abrasion lead to the formation of microplastics. However, until now, there are no established quality assurance concepts for the analysis of microplastic (<5 mm) in environmental compartments, including sampling, processing and analysis. The aim of the present work is the development of suitable examination methods and protocols (sampling, sample preparation and detection) to qualify and quantify microplastic in urbane water management systems. At first a fractional filtration system for sampling and the analytical tool, the so-called TED-GC-MS (thermal desorption gas chromatography mass spectrometry) were developed. The TED-GC-MS method is a two-step analytical procedure which consists of a thermal extraction where the sample is annealed and characteristic decomposition products of the polymers are collected on a solid phase. Afterwards these products are analysed using GC-MS. The developed fractional filtration for sampling and the TED-GC-MS for detection were used for quantitative analysis to screen the waste water influent and effluent of a Berlin waste water treatment plant for the most relevant polymers, polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET) and polyamide (PA). The results of the study revealed that the polymeres PE, PS and PP were detected in the effluent, and PE and PS were find in the raw waste water of the sewage treatment plant in Ruhleben, Berlin. Differences in polymer types and amounts were detected at different sampling dates and within different sieve fractions. Much higher amounts of polymers were observed in the raw waste water. The peak areas of the decomposition products, used for quantification of the polymers, were adjusted using so-called response factors since the TED-GC-MS method is more sensitive for PP and PS than for PE. It has been shown that PE is the most dominant polymer in the samples. Comparing the masses of polymers in the effluent and in the raw sewage, a removal of 99 % of the polymers in the water treatment plant can be assumed. These results are consistent with the literature where removal rates between 98-99 % were described. T2 - SETAC Europe CY - Rom, Italy DA - 13.05.2018 KW - Microplastics KW - Thermogravimetry KW - Waste water KW - Chromatography PY - 2018 AN - OPUS4-44968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paul, Andrea A1 - Wander, Lukas A1 - Becker, Roland A1 - Goedecke, Caroline A1 - Braun, Ulrike T1 - High-throughput NIR spectroscopic (NIRS) detection of microplastics in soil N2 - The increasing pollution of terrestrial and aquatic ecosystems with plastic debris leads to the accumulation of microscopic plastic particles of still unknown amount. To monitor the degree of contamination analytical methods are urgently needed, which help to quantify microplastics (MP). Currently, time-costly purified materials enriched on filters are investigated both by micro-infrared spectroscopy and/or micro-Raman. Although yielding precise results, these techniques are time consuming, and are restricted to the analysis of a small part of the sample in the order of few micrograms. To overcome these problems, here we tested a macroscopic dimensioned NIR process-spectroscopic method in combination with chemometrics. For calibration, artificial MP/soil mixtures containing defined ratios of polyethylene, polyethylene terephthalate, polypropylene, and polystyrene with diameters < 125 µm were prepared and measured by a process FT-NIR spectrometer equipped with a fiber optic reflection probe. The resulting spectra were processed by chemometric models including support vector machine regression (SVR), and partial least squares discriminant analysis (PLS-DA). Validation of models by MP mixtures, MP-free soils and real-world samples, e.g. and fermenter residue, suggest a reliable detection and a possible classification of MP at levels above 0.5 to 1.0 mass% depending on the polymer. The benefit of the combined NIRS chemometric approach lies in the rapid assessment whether soil contains MP, without any chemical pre-treatment. The method can be used with larger sample volumes and even allows for an online prediction and thus meets the demand of a high-throughput method. KW - Microplastics KW - Soil KW - Chemometrics KW - PLS-DA KW - Support vector machines KW - Near Infrared Spectroscopy PY - 2018 DO - https://doi.org/10.1007/s11356-018-2180-2 SN - 1614-7499 SN - 0944-1344 VL - 26 IS - 8 SP - 7364 EP - 7374 PB - Springer AN - OPUS4-45405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goedecke, Caroline T1 - Investigation of sorption of environmental pollutants to virgin and aged microplastic N2 - Plastics are used in many applications, such as packaging, building and construction, mobility and transport and more. Due to their favourable properties like light weight, flexible processing and low costs their production and consequently their input into natural systems has increased significantly over the last decades. In the environment (photo )oxidation processes and mechanical abrasion lead to the decomposition of the plastics. During this process microplastics (<5 mm) can be formed. It has been shown that environmental pollutants can sorb to these microplastics.[1,2] Nevertheless, knowledge on this topic is still limited. Our work aims at the investigation of the sorption behaviour of the triazole fungicide difenoconazole to simulated microplastics made of virgin polyamide (PA), polypropylene (PP), and polystyrene (PS). Sorption experiments were planned based on a full factorial design with agitation, salinity, and pH value as parameters. The results of our study revealed that difenoconazole indeed, has sorbed to all microplastics tested here. Data analysis showed that agitation is the main influencing factor, whereas salinity and the pH value held little to no significance on the amount of sorbed difenoconazole. To simulate the behaviour of naturally aged microplastics, sorption to cryo-milled PP and acid-treated PA was also studied. The thus treated samples were characterised by Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), and dynamic scanning calorimetry (DSC). FTIR spectroscopy did not show any changes in the chemical structure but GPC and DSC measurements indicated a systematic chain scission of the treated PA. Scanning electron microscope (SEM) images illustrate that milling of the microplastics leads to non-spherical, star-shaped particles. This fact has a huge influence on the surface properties and consequently on the absorption. The results of our study are important in terms of i) creating realistic sorption scenarios with relevant parameters for the sorption process, as well as for ii) the choice of proper materials to simulate naturally occurring microplastics. We could show that not only the characteristics of the material like particle size distribution or surface properties are important, but also the applied analytical technique which is used for the characterization of the material . Since there is no standard methodology for microplastic identification and quantification, we suggest to combine several methods to obtain a reliable overall characterization. T2 - ICCE 2017 CY - Oslo, Norway DA - 18.06.2017 KW - Sorption KW - Microplastics KW - Environmental pollutants KW - Dynamic scanning calorimetry PY - 2017 AN - OPUS4-40748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goedecke, Caroline T1 - Detection of microplastic and tire wear particles in road run-off samples using TED-GC-MS N2 - Plastics and rubber are used in many applications, such as packaging, building, construction and mobility. Due to their favourable properties like light weight, flexible processing and low costs their production and consequently their input into the environment has increased significantly over the last decades. In the environment, oxidation processes and mechanical abrasion lead to the decomposition of these plastics into small fragments, called microplastic (< 5 mm). By definition, microplastics only involve thermoplastics and duroplastics but elastomers made out of synthetic polymers (e. g. styrene butadiene rubber), modified natural polymers (e. g. natural rubber) and products of synthetic polymers (e. g. tires) are also part of the current microplastic discussion. The main entry pathway of rubber into the environment is the wear of used tire treads in road traffic. Lassen et al. showed that 60 % of the microplastic emissions in Denmark into the environment come from secondary microplastics generated by tires. Rain events can cause microplastic and rubber to get from the street into the street inlets. Depending on the sewage system, these waters are sometimes not cleaned in the sewage treatment plants and reach the surface waters untreated. To analyse microplastic particles in samples, mainly FTIR or Raman spectroscopic methods are applied at present. Rubber or tire particles in environmental samples cannot be analysed by these methods, because the added carbon black leads to annoying absorption and fluorescent effects. We developed a thermoanalytical method, the so-called TED-GC-MS (thermal extraction desorption gas chromatography mass spectrometry), which allows the simultaneous detection of microplastic and tire wear with almost no sample preparation in about 2.5 h. The TED-GC-MS is a two-step analytical method which consists of a thermobalance and a GC-MS system. Up to 50 mg of an environmental sample is heated up to 600 °C in a nitrogen atmosphere. During pyrolysis, between 300 and 600 °C polymer-specific decomposition products are produced and collected on a solid phase. Afterwards the substances are desorbed, separated and analysed using the GC-MS. The aim of the present work is to present the TED-GC-MS as a time efficient screening method to quantify the industrial most relevant polymers in street run-off samples. Analytical challenges in the determination of polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET) and polyamide (PA), polymethyl methacrylate (PMMA) and styrene-butadiene-rubber (SBR) as a component of tire wear are honestly discussed. The study area is a 200 m long section of the Clayallee in Berlin, a representative typical urban catchment area. The road run-off in this section flows through the gullies directly into a sample chamber, which directs the runoff in an open channel to the rainwater sewer of this area. The sample chamber allows a sample to be taken directly from the road run-off without mixing with the run-off from other areas. The sample chamber is equipped with an automatic sampler. The automatic sampler is controlled by a conductivity sensor to detect the storm event at an early stage. The sensor gives the sampler a signal to start the sampling program when it gets in contact with water and reaches a certain conductivity threshold. The capacity of the sample container is 100 l and the maximum delivery of the automatic sampler is 2.8 l/min. Afterwards, the water was pumped through various stainless-steel sieves with a diameter of approximately 20 cm and mesh widths of 500, 100, 50 μm. The obtained solids were steam sterilized, freeze-dried and measured with the TED-GC-MS. The results of the TED-GC-MS-measurements are summarized in Figure 1. It shows the polymers which were detected in 1 mg of the dry masses of various street run off samples obtained during a period of 1.5 years. We detected PMMA, PS, PP, PE and SBR, as a component of tire wear in the samples. The quantification of the polymers leads to amounts of PS, PP, PE and SBR between 0 µg and 10 µg. PMMA was only detected in traces. T2 - ICCE 2019 CY - Thessaloniki, Greece DA - 16.06.2019 KW - Microplastics KW - TED-GC-MS KW - Road run-off KW - Chromatography PY - 2019 AN - OPUS4-48301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goedecke, Caroline T1 - Analysis of microplastics in theory and in practice N2 - Due to the favorable properties of polymers, their production and thus their input into the environment has increased significantly in recent decades. Currently, FTIR or Raman spectroscopy are mainly applied for the analysis of microplastic particles (MP) in environmental samples. However, these methods have great difficulties in determining metrologically traceable MP values, especially with regard to the limiting values, as preferred in regulation. Therefore, we developed a systematic and fast thermoanalytical method called TED-GC-MS (thermal extraction desorption gas chromatography mass spectrometry), which determines mass contents. Now the current goal is the determination of its process parameters. This poster illustrates the theoretical requirements for MP analysis (left side) and contrast them with the current state of research (right side).Unexpected practical problems are presented and the relatively new method is discussed concerning the quality requirements of well-established methods such as LC-or GC-MS. T2 - Eurachem Workshop - Uncertainty from sampling and analysis for accredited laboratories CY - Berlin, Germany DA - 19.11.2019 KW - Microplastics KW - TED-GC-MS KW - Reference materials PY - 2019 AN - OPUS4-49665 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Goedecke, Caroline A1 - Bannick, C.-G. A1 - Abusafia, A. A1 - Scheid, C. A1 - Steinmetz, H. A1 - Paul, Andrea A1 - Beleites, C. A1 - Braun, U. T1 - Identification of microplastic pathways within a typical European urban wastewater system N2 - In recent years, thermoextraction/desorption-gas chromatography/mass spectrometry (TED-GC/MS) has been developed as a rapid detection method for the determination of microplastics (MP) mass contents in numerous environmentally relevant matrices and, in particular, for the measurement of polymers in water samples without time-consuming sample preparation. The TED-GC/MS method was applied to investigate a typical European municipal wastewater system for possible MP masses. Such investigations are important in view of the recent revision of the Urban Wastewater Treatment Directive. Four different representative sampling sites were selected: greywater (domestic wastewater without toilet), combined sewer, and influent and effluent of a wastewater treatment plant (WWTP). All samples were collected by fractional filtration. Filtration was carried out over mesh sizes of 500, 100, 50, and in some cases, 5 µm. Polyethylene (PE), polypropylene (PP), and polystyrene (PS) were detected in all samples, with the PE fraction dominating in all cases. Styrene-butadiene rubber which serves as an indication of tire abrasion, was only found in the influent of the WWTP. The highest MP mass contents were found in the combined sewer, so MP can become a source of pollution during heavy rain events when the capacity limits of the effluent are reached, and the polluted effluent is released uncontrolled into the environment. Based on the studies, MP retention from the WWTP could be estimated to be approximately 96%. Few trends in polymer type or mass contents were detected within the different fractions of the samples or when comparing samples to each other. KW - Microplastics KW - Microplastic analysis KW - TED-GC/MS KW - Microplastic pathways KW - Mass contents PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-568289 DO - https://doi.org/doi.org/10.1002/appl.202200078 SP - 1 EP - 10 PB - Wiley-VCH CY - Weinheim AN - OPUS4-56828 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -