TY - CONF A1 - Roland, U. A1 - Trommler, U. A1 - Hoyer, C. A1 - Pfütze, C. A1 - Plarre, Rüdiger A1 - Rabe, C. A1 - Höhlig, B. A1 - Holzer, F. A1 - Kraus, M. A1 - Schmidt, D. A1 - Kopinke, F.-D. T1 - Radio-frequency heating for pest control, decontamination and drying of timber and masonry N2 - A number of very relevant processes for protection and reconstruction of buildings can be supported by controlled heating: elimination of pests without using hazardous Chemicals, drying and decontamination of timber and many other building materials. For this purpose, radio-frequency (RF) dielectric heating is an advantageous Option because the materials and structures can be heated directly by energy absorption in the volume, homogeneously and, if required, relatively fast. Compared to microwaves, the penetration depths are usually much larger and the flexibility with respect to different materials is wider. Namely, heating can also be realized for dry materials because the dielectric loss is as not closely related to the presence of water as for microwave applications. T2 - 14th International conference on microwave and high frequency heating CY - Nottingham, UK DA - 16.09.2013 KW - Radio-frequency heating KW - Drying KW - Decontamination KW - Pest control KW - Timber KW - Masonry PY - 2013 SN - 978-0-85358-293-9 SP - 112 EP - 115 AN - OPUS4-29269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hoyer, C. A1 - Pfütze, C. A1 - Plarre, Rüdiger A1 - Trommler, U. A1 - Steinbach, S. A1 - Klutzny, Kerstin A1 - Holzer, F. A1 - Rabe, C. A1 - Höhlig, B. A1 - Kopinke, F.-D. A1 - Schmidt, D. A1 - Roland, U. T1 - Chemikalienfreie Bekämpfung von Holzschädlingen durch dielektrische Erwärmung mit Radiowellen und Mikrowellen N2 - Die thermische Bekämpfung von Holzschädlingen erfordert wegen der geringen Wärmeleitfähigkeit von Holz lange Behandlungszeiten und kann zur Rissbildung führen. Hier wurde die thermische Behandlung mittels Radio- und Mikrowellen untersucht. Die direkte, dielektrische Erwärmung hat den Vorteil einer größeren Homogenität der Aufheizung. Die mit Radiowellen erzielten Temperaturprofile waren homogener als die mit Mikrowellen realisierten. Untersuchungen zeigten, dass die Abtötung nicht auf die direkte Einwirkung von elektromagnetischen Feldern, sondern auf die Temperaturerhöhung zurückzuführen ist.-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Thermal pest control requires long treatment times due to the low thermal conductivity of wood and may lead to the formation of cracks. Here, the thermal treatment with radio waves as well as microwaves has been studied. The direct dielectric heating has the advantage of a good homogeneity. The obtained temperature profiles for radio waves were more homogeneous compared to microwaves. Detailed studies showed that elimination of pests was not related to the application of the electromagnetic field itself, but due to the temperature increase. KW - Dielektrische Erwärmung KW - Holzschutz KW - Mikrowellen KW - Radiowellen KW - Bekämpfung KW - Insekten KW - Dielectric heating KW - Microwaves KW - Pest control KW - Radio waves PY - 2014 DO - https://doi.org/10.1002/cite.201300091 SN - 0009-286X SN - 1522-2640 VL - 86 IS - 8 SP - 1187 EP - 1197 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-31301 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hoyer, C. A1 - Pfütze, C. A1 - Plarre, Rüdiger A1 - Trommler, U. A1 - Steinbach, S. A1 - Klutzny, Kerstin A1 - Holzer, F. A1 - Rabe, C. A1 - Höhlig, B. A1 - Schmidt, S. A1 - Roland, U. T1 - Chemical-free pest control by dielectric heating with radio waves and microwaves: Thermal effects N2 - Thermal pest control with hot air is widely accepted as an alternative to chemical methods. However, it requires relatively long treatment times owing to the low thermal conductivity of wood. Direct dielectric heating that applies radio waves or microwaves has the advantage of more homogeneous heating. However, Sound experimental data on this technique are currently rare. Therefore, the thermal treatment of wood-destroying insects with radio waves and microwaves was studied with two model pests, Anobium punctatum and Hylotrupes bajulus, and with Tenebrio molitor as a reference. The secure elimination of pests was achieved, and the corresponding treatment time was in the range of a few minutes. Temperature profiles were more homogeneous when applying radio waves. KW - Dielectric heating KW - Microwaves KW - Pest control KW - Radio waves KW - Wood protection PY - 2018 DO - https://doi.org/10.1002/ceat.201600712 SN - 1521-4125 SN - 0930-7516 VL - 41 IS - 1 SP - 108 EP - 115 PB - Wiley-VCH CY - Weinheim AN - OPUS4-43527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mohammadifar, E. A1 - Ahmadi, V. A1 - Gholami, M.F. A1 - Oehrl, A. A1 - Kolyvushko, O. A1 - Nie, C. A1 - Donskyi, Ievgen A1 - Herziger, S. A1 - Radnik, Jörg A1 - Ludwig, K. A1 - Böttcher, C. A1 - Rabe, J.P. A1 - Osterrieder, K. A1 - Azab, W. A1 - Haag, R. A1 - Adeli, M. T1 - Graphene-Assisted Synthesis of 2D Polyglycerols as Innovative Platforms for Multivalent Virus Interactions N2 - 2D nanomaterials have garnered widespread attention in biomedicine and bioengineering due to their unique physicochemical properties. However, poor functionality, low solubility, intrinsic toxicity, and nonspecific interactions at biointerfaces have hampered their application in vivo. Here, biocompatible polyglycerol units are crosslinked in two dimensions using a graphene-assisted strategy leading to highly functional and water-soluble polyglycerols nanosheets with 263 ± 53 nm and 2.7 ± 0.2 nm average lateral size and thickness, respectively. A single-layer hyperbranched polyglycerol containing azide functional groups is covalently conjugated to the surface of a functional graphene template through pH-sensitive linkers. Then, lateral crosslinking of polyglycerol units is carried out by loading tripropargylamine on the surface of graphene followed by lifting off this reagent for an on-face click reaction. Subsequently, the polyglycerol nanosheets are detached from the surface of graphene by slight acidification and centrifugation and is sulfated to mimic heparin sulfate proteoglycans. To highlight the impact of the two-dimensionality of the synthesized polyglycerol sulfate nanosheets at nanobiointerfaces, their efficiency with respect to herpes Simplex virus type 1 and severe acute respiratory syndrome corona virus 2 inhibition is compared to their 3D nanogel analogs. Four times stronger in virus Inhibition suggests that 2D polyglycerols are superior to their current 3D counterparts.2D nanomaterials have garnered widespread attention in biomedicine and bioengineering due to their unique physicochemical properties. However, poor functionality, low solubility, intrinsic toxicity, and nonspecific interactions at biointerfaces have hampered their application in vivo. Here, biocompatible polyglycerol units are crosslinked in two dimensions using a graphene-assisted strategy leading to highly functional and water-soluble polyglycerols nanosheets with 263 ± 53 nm and 2.7 ± 0.2 nm average lateral size and thickness, respectively. A single-layer hyperbranched polyglycerol containing azide functional groups is covalently conjugated to the surface of a functional graphene template through pH-sensitive linkers. Then, lateral crosslinking of polyglycerol units is carried out by loading tripropargylamine on the surface of graphene followed by lifting off this reagent for an on-face click reaction. Subsequently, the polyglycerol nanosheets are detached from the surface of graphene by slight acidification and centrifugation and is sulfated to mimic heparin sulfate proteoglycans. To highlight the impact of the two-dimensionality of the synthesized polyglycerol sulfate nanosheets at nanobiointerfaces, their efficiency with respect to herpes Simplex virus type 1 and severe acute respiratory syndrome corona virus 2 inhibition is compared to their 3D nanogel analogs. Four times stronger in virus Inhibition suggests that 2D polyglycerols are superior to their current 3D counterparts. KW - 2D Materials KW - Graphene template KW - Multivalency KW - Polyglycerol KW - Virus inhibition PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527726 DO - https://doi.org/10.1002/adfm.202009003 VL - 31 IS - 32 SP - 2009003 PB - Wiley VCH AN - OPUS4-52772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten A1 - Naghib Zadeh, Hamid A1 - Glitzky, C. A1 - Töpfer, J. T1 - Integration of Ni-Cu-Zn ferrite in LTCC-modules N2 - Integration of magnetic functional components in LTCC Circuit boards calls for co-firing of dielectric and ferrite tapes. Ni-Cu-Zn ferrites with permeability of p=900 were developed which can be fully densified at the Standard LTCC sintering temperature of 900 °C. Successful co-firing of this ferrite with dielectric tapes requires the adaptation of the shrinkage behavior of the materials as well as the thermal expansion during the cooling period - especially in the temperature range below the transformation point of the glassy phase of the dielectric tape. To match these preconditions, a new dielectric LTCC material with steep sintering curve and high thermal expansion coefficient was designed. Sintered multilayer composed of Ni-Cu-Zn ferrite and tailored dielectric tapes are free of cracks and possess no open porosity. No significant interdiffusion between the ferrite and dielectric tapes was found by EDX measurements. Compared to pure ferrite laminates the permeability of co-sintered Ni-Cu-Zn ferrite layers is drastically reduced to 400, i.e. a decrease of more than 50 %. To investigate the origin of this permeability reduction, Ni-Cu-Zn ferrite laminates were sintered separately, and in combination with alumina release tapes or dielectric tapes, respectively. SEM and EDX analysis of co-fired laminates reveal differences in the ferrite grain growth behavior. Ferrite laminates with homogeneous microstructure and grain size up to 50 pm exhibit large permeability. However, growth of ferrite grains does not take place near the interface between ferrite and release or dielectric tapes. There is a strong correlation between high permeability and volume fraction of large ferrite grains. Regions of fine and coarse grains inside the ferrite layers show different bismuth concentration; the Bi-content is larger in regions of fine ferrite grains. T2 - CICMT 2011 - 7th International conference and exhibition on ceramic interconnect and ceramic microsystems technologies CY - San Diego, CA, USA DA - 05.04.2011 KW - LTCC KW - Co-firing KW - Ferrite KW - Shrinkage behavior KW - Constrained sintering KW - Keramische Multilayer KW - Grenzflächenreaktion PY - 2011 SN - 0-930815-92-0 SP - 000266 EP - 000275 PB - IMAPS, International Microelectronics and Packaging Society AN - OPUS4-25072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberstein, Markus A1 - Glitzky, Carsten A1 - Gemeinert, Marion A1 - Rabe, Torsten A1 - Schiller, Wolfgang Arno A1 - Modes, C. T1 - Design of LTCC with high thermal expansion T2 - IMAPS/ACERS 4th International Conference and Exhibition on Ceramic Interconnect and Ceramic Microsystems Technologies (CICMT 2008) CY - Munich, Germany DA - 2008-04-21 KW - LTCC KW - Glass ceramic composites KW - Coefficient of thermal expansion CTE KW - Design PY - 2008 SP - 000120 EP - 000126 PB - IMAPS, International Microelectronics and Packaging Society CY - Washington, DC AN - OPUS4-17436 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eberstein, Markus A1 - Glitzky, Carsten A1 - Gemeinert, Marion A1 - Rabe, Torsten A1 - Schiller, Wolfgang Arno A1 - Modes, C. T1 - Design of LTCC with high thermal expansion N2 - New applications of low-temperature co-fired ceramics (LTCC), such as pressure sensors or integrated functional layers, require materials that possess higher coefficients of thermal expansion (CTE). To fabricate LTCC with elevated CTE, two methods of material design are examined: firstly, glass ceramic composites (GCC), which consist of >50 vol% glass in the starting powder, and, secondly, glass-bonded ceramics (GBC), where glass is added as a sintering aid only. The CTE of GBC is mainly determined by the crystalline component. For GCC, the CTE can be well predicted, if CTE and elastic data of each phase in the microstructure are known. A nonlinear characteristic of the CTE versus phase composition was found with increasing Ecrystals/Eglass ratio and absolute CTE difference between the components. The glass composition and glass amount can be used to compensate the fixed properties of a crystalline material in a desired way. However, because the CTE and permittivity of a glass cannot be chosen independently, an optimum glass composition has to be found. For a given LTCC, it is possible to control the devitrification by shifting the glass composition. In this way, the resulting CTE values can be predicted more exactly and tailoring becomes possible. Different LTCC materials, based on the crystalline compounds Ba(La,Nd)2Ti4O12, ZrO2 (Y-TZP), SiO2 (quartz), and specially developed glasses, possessing an elevated CTE of around 10 × 10-6 K-1 while showing permittivity εr between 6 and 63, are introduced. KW - LTCC KW - Glass ceramic composites KW - Coefficient of thermal expansion CTE KW - Design PY - 2009 DO - https://doi.org/10.1111/j.1744-7402.2008.02316.x SN - 1546-542X SN - 1744-7402 VL - 6 IS - 1 SP - 1 EP - 8 PB - American Ceramic Soc. CY - Westerville, Ohio AN - OPUS4-18675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaebler, A. A1 - Moessinger, A. A1 - Goelden, F. A1 - Manabe, A. A1 - Goebel, M. A1 - Follmann, R. A1 - Koether, D. A1 - Modes, C. A1 - Kipka, A. A1 - Deckelmann, M. A1 - Rabe, Torsten A1 - Schulz, Bärbel A1 - Kuchenbecker, Petra A1 - Lapanik, A. A1 - Mueller, S. A1 - Haase, W. A1 - Jakoby, R. T1 - Liquid crystal-reconfigurable antenna concepts for space applications at microwave and millimeter waves N2 - Novel approaches of tunable devices for millimeter wave applications based on liquid crystal (LC) are presented. In the first part of the paper, a novel concept of a tunable LC phase shifter realized in Low Temperature Cofired Ceramics technology is shown while the second part of the paper deals with a tunable high-gain antenna based on an LC tunable reflectarray. The reflectarray features continuously beam scanning in between ±25°. Also first investigations on radiation hardness of LCs are carried out, indicating that LCs might be suitable for space applications. KW - Tunable antenna KW - Phase shifter KW - Liquid crystal KW - LTCC PY - 2009 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-194273 DO - https://doi.org/10.1155/2009/876989 SN - 1687-5877 VL - 2009 IS - Article ID 876989 SP - 1 EP - 7 PB - Hindawi Publishing Corporation CY - New York, NY, USA AN - OPUS4-19427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Faghani, A. A1 - Gholami, M. F. A1 - Trunk, M. A1 - Müller, J. A1 - Pachfule, P. A1 - Vogl, S. A1 - Donskyi, Ievgen A1 - Li, M. A1 - Nickl, Philip A1 - Shao, J. A1 - Huang, M. R. S. A1 - Unger, Wolfgang A1 - Arenal, R. A1 - Koch, C. T. A1 - Paulus, B. A1 - Rabe, J. P. A1 - Thomas, A. A1 - Haag, R. A1 - Adeli, M. T1 - Metal-Assisted and Solvent-Mediated Synthesis of Two-Dimensional Triazine Structures on Gram Scale N2 - Covalent triazine frameworks are an emerging material class that have shown promising performance for a range of applications. In this work, we report on a metal-assisted and solvent-mediated reaction between calcium carbide and cyanuric chloride, as cheap and commercially available precursors, to synthesize two-dimensional triazine structures (2DTSs). The reaction between the solvent, dimethylformamide, and cyanuric chloride was promoted by calcium carbide and resulted in dimethylamino-s-triazine intermediates, which in turn undergo nucleophilic substitutions. This reaction was directed into two dimensions by calcium ions derived from calcium carbide and induced the formation of 2DTSs. The role of calcium ions to direct the two-dimensionality of the final structure was simulated using DFT and further proven by synthesizing molecular intermediates. The water content of the reaction medium was found to be a crucial factor that affected the structure of the products dramatically. While 2DTSs were obtained under anhydrous conditions, a mixture of graphitic material/2DTSs or only graphitic material (GM) was obtained in aqueous solutions. Due to the straightforward and gram-scale synthesis of 2DTSs, as well as their photothermal and photodynamic properties, they are promising materials for a wide range of future applications, including bacteria and virus incapacitation. KW - XPS KW - Triazine KW - 2D PY - 2020 DO - https://doi.org/10.1021/jacs.0c02399 VL - 142 IS - 30 SP - 12976 EP - 12986 PB - ACS American Chemical Society AN - OPUS4-51203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jost, M. A1 - Strunck, S. A1 - Heunisch, Andreas A1 - Wiens, A. A1 - Prasetiadi, A.E. A1 - Weickhmann, C. A1 - Schulz, Bärbel A1 - Quibeldey, M. A1 - Karabey, O.H. A1 - Rabe, Torsten A1 - Follmann, R. A1 - Koether, D. A1 - Jakoby, R. T1 - Continuously tuneable liquid crystal based stripline phase shifter realised in LTCC technology N2 - This work presents the design, fabrication and measurements of a low temperature cofired ceramic (LTCC) integrated liquid crystal (LC) phase shifter. The effective permittivity of the phase shifter and therefore its differential phase shift can be tuned continuously by orienting the LC directors with electric fields. The phase-shift demonstrator is designed for Ka-band frequencies around 30 GHz and represents a stripline filled with LC, embedded inside an LTCC multilayer structure, which provides a space-qualified and hermetically-sealed LC cavity within an RF-capable material system. The total length of the device is 37 mm while the phase shifting LC section has a length of 14.6 mm. At 30 GHz it exhibits a differential phase shift of 60° with an insertion loss around 6 dB, resulting in a figure of merit around 10°/dB. An advantage is that the insertion loss is nearly independent of the tuning state of the LC. The response time of the phase shifter, depending on the desired LC orientation, is between 62 ms and 37 s. T2 - EuMC 2015 - 45th European microwave conference CY - Paris, France DA - 07.09.2015 PY - 2015 SN - 978-2-87487-039-2 SP - 1260 EP - 1263 AN - OPUS4-35268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -