TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg T1 - Recycling of waste materials by thermochemical treatment T2 - ISWA World congress 2010 - Urban development and sustainbility - a major challenge for waste management in the 21st century CY - Hamburg, Germany DA - 2010-11-15 KW - thermochemical substance separation KW - Thermodynamics KW - Thermochemistry PY - 2010 SP - 1 EP - 10(?) AN - OPUS4-22467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement durch thermochemische Behandlung von mineralischen Nebenprodukten und Abfällen N2 - Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Sekundärrohstoff PY - 2022 SN - 978-3-944310-58-9 SP - 372 EP - 385 PB - TK-Verlag CY - Neuruppin AN - OPUS4-54737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Mory, D. A1 - Schilller, D. A1 - Adam, Christian T1 - Chemische Onlineanalyse von Schmelzen im Lichtbogenofen durch LIBS N2 - Die Reduktion von Metalloxiden zum Metall in einer schmelzflüssigen mineralischen Matrix stellt die Grundlage vieler metallurgischer Verfahren dar. Eine Prozessoptimierung und -kontrolle setzt allerdings die genaue Kenntnis der chemischen Zusammensetzung der Schmelze voraus. Im Beitrag wird LIBS als Methode zur Online-Analyse von Hochtemperaturschmelzen vorgestellt. T2 - Schlacken Symposium 2016 CY - Meitingen, Germany DA - 13.10.2016 KW - Online-Analyse KW - LIBS KW - Lichtbogenofen KW - Prozessoptimierung PY - 2016 SP - 49 EP - 58 AN - OPUS4-38155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Schraut, Katharina A1 - Adam, Christian ED - Thiel, S. ED - Thomé-Kozmiensky, E. ED - Friedrich, B. ED - Pretz, T. ED - Quicker, P. ED - Senk, D. G. ED - Wortruba, H. T1 - Nachbehandlung von Stahlwerksschlacken und deren Verwertung als Klinkermaterial T1 - Post-treatment of steelmaking slags and their utilisation as cement clinker N2 - Steelmaking slags produced using the Linz-Donawitz method (LD slags) are widely used as building and construction materials in road, earth and water works. Because the legal conditions become more and more re-strictive , this application is uncertain in the future. LD slags contain high amounts of mineral bound iron (in form of Fe2O3), which must be considered as a waste of resources. Except for the Iron the chemical composition is quite similar to that of Portland cement clinker. However, due to the high content of Fe2O3 the mineralogical composition differs significantly, resulting in a low hydraulic reactivity. A post-treatment of the liquid LD slag in an electric arc furnace under reducing conditions enables the reduction of the iron compounds to metallic iron, which separates from the mineral phase due to its higher density. The remaining solidified mineral fraction mainly contains typical crystalline phases of cement clinker in similar ratios: Alite (Ca3SiO5; > 60%) as main phase, Belite (Ca2SiO4, 10%), Tricalciumaluminate (Ca3Al2O6; 5%) and Brownmillerite (Ca2(Al,Fe)2O5, 1%) as secondary phases. Alite, which usually decomposes to Belite and free lime under slow cooling conditions, is stabilized in the Fe-reduced slag probably by integration of foreign ions into the lattice and is stable even if the slag is cooled down very slowly. Furthermore, the particularly large Alite crystals do not exhibit the typical decomposition edge of Belite and lime, found in Alite from ordinary ce-ment clinker. Technological tests for building materials show a high hydraulic reactivity and a compressive strength after 28 days comparable or even slightly higher to reference cement. Nevertheless, because of the increasing viscosity with decreasing Fe2O3 content, the treatment requires a temperature higher than the slag decanted from the LD converter. Furthermore, during the reduction of the bound Iron huge amounts of carbon monoxide are released, resulting in foaming of the slag. Both aspects make it difficult to manage the process. In addition, for economic reasons the treatment has to be carried out immediately after casting the slag from the LD converter to avoid the solidification, which is a logistical challenge for most steel plants. Otherwise the separation of the mineral bound iron as metallic phase and the utilisation of the mineral fraction as cement clinker will both save resources and lower the global CO2-output. For these reasons further initiatives should be considered in the medium term. N2 - LD-Schlacken weisen eine große chemische Ähnlichkeit zu Protlandzementklinker auf. Sie enthalten jedoch noch bis zu 30% Eisen, das mineralisch in oxidischer Form gebunden vorliegt. Dadurch kann sich bei der Erstarrung die wichtigste Klinkerphase "Alit" nicht ausbilden. Durch eine reduzierende Schmelzbehandlung der Schlacke kann des mineralisch gebundene Eisen als Metall separiert werden. Dadurch wird auch die Mineralogie der Schlacke so verändert, dass auch sie nun praktisch einem Portlandzementklinker entspricht. Entsprechende Versuche wurden am kleintechnischen Lichtbogenofen der BAM durchgeführt. Es werden Ergebnisse vorgestellt und auf Grenzen und Möglichkeiten eines derartigen Prozesses im Hinblick auf eine industrielle Umsetzung eingegangen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 11.06.2018 KW - Zementklinker KW - Stahlwerksschlacke KW - LD-Schlacke KW - Lichtbogenofen KW - Alit PY - 2018 SN - 978-3-944310-41-1 VL - 5 SP - 282 EP - 296 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-45199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Armatys, Kamila A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Pflumm, R. A1 - Galetz, M. C. T1 - Corrosion and abrasion resistant protective coatings for biomass combustion N2 - The environmental concerns about availability of fossil fuels and greenhouse gas effect increase and alternative renewable fuels for power plants are gaining significantly of importance. One of the alternative renewable fuels is biomass but it is a difficult fuel because of its diversity and complexity. It can contain high percentages of K and Cl responsible for corrosion together with sand that have additionally an abrasive effect during combustion. Because of permanently extending the surface reaction due to abrasion the corrosion of the materials increases. In particular in power plants, the superheater tubes are exposed to a corrosive abrasive attack that is one of the main sources of concern. The development of new alloys for multilayer surface, which combines corrosive and abrasive resistance is therefore of high importance. Those new technical approaches must be at the same time cost-effective to be an alternative to conventional materials. This paper presents the principle of experimental methods developed for the investigations of high temperature corrosion combined with abrasion in thermochemical processes with high hydrochloric acid concentrations like during biomass combustion. The aim of the presented investigation methods it to test and develop suitable alloys for coatings for the super heater tubes of biomass power plants. First results of abrasion investigations show improved abrasion resistance compared to the multi-component reference material Alloy 625. T2 - Young Researchers Conference: Energy Efficiency & Biomass CY - Wels, Austria DA - 24.02.2016 KW - Corrosion KW - Coatings PY - 2016 SP - 1 EP - 9 CY - Proceedings in Young Researchers Conference: Energy Efficiency & Biomass 2016 AN - OPUS4-35714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kley, Gerd A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg A1 - Köcher, Peter T1 - Thermochemical treatment - Technologies for recovery and upvaluation of materials T2 - 7th World Congress on Recovery, Recycling and Re-integration CY - Bejing, China DA - 2006-05-25 KW - Thermochemie KW - Lichtbogenofen KW - Dekontaminierung KW - Recycling KW - Verwertung KW - Ressourcenschutz KW - Silikatprodukte KW - Feuerfest KW - Schlacken PY - 2005 SP - 1 EP - 10(?) PB - Beijing Kexin Printing House CY - Peking AN - OPUS4-11540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, D. A. A1 - Adam, Christian T1 - Zementklinker durch Nachbehandlung von Stahlwerksschlacken N2 - Die Klinkerphasenbildung durch Sinterung in Drehrohröfen bei der Herstellung von Portlandzementklinker (PZK) ist gründlich erforscht und optimiert. Im Hinblick auf mögliche ökonomische und ökologische Vorteile befassen sich aktuelle Forschungsvorhaben darüber hinaus mit der Herstellung von Klinkermineralen aus Stahlwerksschlacken, die eine vergleichbare chemische Zusammensetzung aufweisen. Neuste Untersuchungen zeigen, dass nach der reduzierenden Behandlung schmelzflüssiger Linz-Donawitz-(LD)-Schlacken und Abscheidung des gebildeten metallischen Eisens eine mineralische Schlacke entsteht, die unabhängig von ihren Abkühlbedingungen ca. 50–60 Gew.% des wichtigsten Klinkerminerals Alit (C3S) enthält und eine hohe hydraulische Reaktivität aufweist. Die Stabilität des Alits auch nach langsamer Abkühlung deutet auf eine Stabilisierung des Minerals durch Nebenelemente aus den LD-Schlacken hin. Ein sinkender Anteil an LD-Schlacke durch Zusatz synthetischer Schlackemischung, die sich hinsichtlich ihrer Hauptkomponenten wie eine ausreduzierte LD-Schlacke zusammensetzt, führt zu einem Rückgang des Alitgehaltes und dem Zerfall der Schlacke beim Erstarren. T2 - 5. Schlacken-Symposium CY - Meitingen, Germany DA - 25.10.2018 KW - LD-Schlacke KW - Zement KW - Tricalciumsilikat PY - 2018 SP - 219 EP - 229 PB - Max Aicher Unternehmensgruppe AN - OPUS4-46412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, D. A1 - Kargl, F. A1 - Adam, Christian T1 - Formation and chemical stabilisation of tricalcium-silicate during solidification from the melt of post-treated metallurgical slags N2 - Tricalcium-silicate (C3S) or Alite is the most important mineral in Portland cement. Since pure tricalcium-silicate is only stable above temperatures of 1250 °C, its decomposition has to be prevented technically by fast cooling after the sintering process. At room temperature, the decomposition velocity is very slow so that metastable tricalcium-silicate is obtained. Although the mechanisms of clinker phase formation during burning process of Portland cement in a rotary kiln were solved and improved over the years, in view of possible economic and ecological benefits current projects aim to produce clinker phases from metallurgical slags. Recent studies discovered that the mineral phase which remained after a reducing treatment and separation of formed metallic iron from molten Linz-Donawitz (LD-) slags contained about 60 wt.% Alite despite it was cooled slowly. Because the results could be verified using slags from different origins and varying cooling velocities a chemical stabilisation of the Alite can be assumed. First tests in mortars indicate that workability, hardening and solid state properties are comparable with an ordinary Portland cement. An application of the observed phenomenon in cement production requires enhanced knowledge about formation and stabilisation conditions of Alite during crystallisation from melts in contrast to the sintering reactions in conventional Portland cement production. Therefore, this study focuses on the stabilisation mechanisms of Alite in consolidating melts. Samples from different melting experiments are analysed to determine stabilising factors. T2 - 15th International Congress on the Chemistry of Cement CY - Prag, Czech Republic DA - 16.09.2019 KW - Tricalcium-silicate KW - Portland Cement KW - Alite KW - Steelmaking slag PY - 2019 SP - Paper 492, 1 EP - 10 AN - OPUS4-49050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Kalbe, Ute A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Weimann, Karin T1 - Recovery of non-renewable resources from waste T2 - 7th International Conference on EcoBalance CY - Tsukuba, Japan DA - 2006-11-14 KW - Natural resources KW - Thermo-chemical treatment KW - Waste management KW - Sewage sludge KW - Aggregetes PY - 2006 IS - E2-4 SP - 499 EP - 502 PB - The Society of Non-Traditional Technology CY - Tsukuba, Japan AN - OPUS4-14115 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical tantalum and niobium recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 SN - 978-3-940276-87-2 VL - 1 SP - 371 EP - 386 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-48363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -