TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Feistkorn, S. ED - Barros, J. ED - Sena-Cruz, J. T1 - Durability of CFRP-laminate strengthening N2 - First bridge structures have been strengthened by means of Carbon-Fiber-Reinforced-Polymer (CFRP)-laminates extemally glued to the concrete surface in the last two decades. At present there is no Information about the durability of these Systems after having been in Service for more than ten years. The paper presents laboratory tests and case studies with automated non-destructive testing to analyse the current bond condition of extemally bonded CFRP-laminates to concrete structures, strengthened about ten years ago. The paper presents the feasibility and the limitations of ultrasonic inspection of selected areas of CFRP-laminate-strengthened structures co-funded by the German Center of Competence in Civil Engineering (DIBt) in a national project. Areas of interest were the end region of laminates or areas with educated doubts about their bond integrity selected and marked in the inspection records during main inspections. In a feasability study, the functionality of the ultrasonic test for bond evaluation below CFRP-laminates without any surface protection measure, was confirmed by testing a CFRP-laminate strengthened slab with artificial voids in a blind laboratory test with an accuracy of + 1 cm. The accuracy depends on the step width, line interspace and the distance between ultrasonic transducer and receiver. This accuracy suits a measuring grid of 1 cm. The case studies consider flexural strengthening and repair of prestressed concrete structures as well as longitudinal and transverse strengthening of bridge slabs with simple reinforcement. Both alternatives were considered, covered with mineral surface protection layer and without. The measurement results of automated scanned surfaces is presented in color-codes images. In the tested areas with no or thin surface protection the non-destructive inspection did not uncover severe defects or Deterioration processes. None the less, proposals for further research is given, in testing of the acceptable bond defects and in advancing the ultrasonic test including the devlopment of sensors for this application. T2 - FRPRCS-11 - 11th International symposium on fiber reinforced polymer for reinforced concrete structures CY - Guimaraes, Portugal DA - 26.06.2013 KW - CFRP-Laminate KW - Debonding KW - Flexural strengthening KW - Bridge KW - NDT KW - Durability test KW - Inspection PY - 2013 SN - 978-972-8692-84-1 SP - 41 EP - 42 (Session 6.5) AN - OPUS4-28859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Röllig, Mathias A1 - Kind, Thomas A1 - Lai, W. T1 - Qualitätssicherung für textilfaserverstärkten Beton N2 - Beim Bauen im Bestand ist die zusätzlich aufzunehmende Last in der Regel zu beschränken. Das trifft insbesondere für schon gerissene Elemente wie Gewölbe odör alternde Betonkonstruktionen zu. Da Hochleistungsfasern wie Textilgelege aus Carbonfasern oder alkaliresistenten (AR-)Glasfasern keinen Korrosionsschutz erfordern, kann die Verbundschicht aus Feinkornbeton dünn gehalten werden, um das Bauwerk nur mit einer Mindestzusatzlast zu beanspruchen. Textilbeton heißt die neue Bauweise, für die es zurzeit noch kein festgeschriebenes Qualitätssicherungs- und Wartungskonzept für Bau und die spätere Nutzung gibt. T2 - 5. Anwendertagung Textilbeton CY - Friedrichshafen, Germany DA - 24.09.2013 KW - Textilfaserverstärkter Beton KW - Zerstörungsfreie Prüfung KW - Ultraschall-Echo KW - Radar-Echo PY - 2013 VL - 9 SP - 22 AN - OPUS4-29512 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Milmann, Boris A1 - Helmerich, Rosemarie A1 - Köpp, Christian A1 - Mielentz, Frank A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Moryson, R.-M. A1 - Samokrutov, A. A1 - Alekhin, S. G. A1 - Alver, Ninel A1 - Sazak, H.-Ö. ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Ultrasound based monitoring system for concrete monolithic objects N2 - Ultrasound sensors should be embedded into concrete for monitoring concrete properties. These new longitudinal wave sensors with a center frequency of 60 kHz were examined regarding their suitability for ultrasonic measurements in concrete structures in terms of emission characteristics, sensitivity and frequency ränge. For the measurement of the radiation patterns, the sensors were embedded vertically and horizontally in concrete cylinders. The directivity pattern was measured using a laser vibrometer. The sensitivity of the sensor was determined in water using different sensors of the same type. It shows changes in the signal amplitude as well as variations in the frequency ränge for different transmitter-receiver combinations. The attenuation of the concrete affects the achievable resolution of the measurements and thus, the maximum possible spacing of the sensors within a concrete element. Experimental tests helped optimizing the distances with respect to the required resolution and the effort of embedding the sensors. The signal attenuation in the concrete was measured in the frequency ränge of 60 kHz in response to various degrees of reinforcement and grain size. For this purpose, the sensors were cast at different distances in the specimens studied. The recorded Signals were evaluated for their amplitude and frequency spectrum. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Ultrasound KW - Concrete KW - Monitoring system KW - Ultrasonic network KW - Embedded sensor PY - 2013 SN - 978-962-367-768-4 SP - 1 EP - 6 AN - OPUS4-29642 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Wiggenhauser, Herbert T1 - Grundlagenuntersuchungen von Ultraschall-Sensoren in Beton N2 - Für Ultraschallmessungen in Betonbauteilen wurden neuartige radialsymmetrisch abstrahlende Longitudinalwellenprüfköpfe mit einer Mittenfrequenz von 60 kHz auf deren Eignung hinsichtlich Abstrahlcharakteristik, Empfindlichkeit und Frequenzspektrum untersucht. Für die Messung der Abstrahlcharakteristiken wurden die Prüfköpfe vertikal und horizontal in Betonzylinder eingebettet und die Richtungsabhängigkeiten der Schallschnelle mithilfe eines Laservibrometers gemessen. Die Streuung der Prüfkopfempfindlichkeit wurde im Wasserbad unter Verwendung verschiedener Köpfe gleicher Bauart bestimmt. Außer Änderungen der Signalamplituden zeigten sich auch Schwankungen im Frequenzbereich bei verschiedenen Sender-Empfängerkombinationen. Die Schallschwächung des Betons hat Einfluss auf die erreichbare Auflösung der Messungen und damit auf die maximal möglichen Senderabstände im Bauteil. Durch experimentelle Untersuchungen und Simulationen erfolgte eine Optimierung der Abstände hinsichtlich des Aufwandes und der geforderten Auflösung. Die Signalschwächung im Beton wurde mit verschiedenen Impulsen im Frequenzbereich von 50 kHz bis 100 kHz in Abhängigkeit verschiedener Bewehrungsgrade und Korngrößen ermittelt. Hierfür wurden die Sensoren in unterschiedlichen Abständen in die Probekörper einbetoniert und die Empfangssignale hinsichtlich Amplitudenabfall und Frequenzspektrum untersucht. T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-294153 SN - 978-3-940283-49-8 IS - DGZfP-BB 141 (Poster 56) SP - 1 EP - 9 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-29415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -