TY - JOUR A1 - Böhning, Martin A1 - Goering, Harald A1 - Fritz, Andreas A1 - Brzezinka, Klaus-Werner A1 - Turky, Gamal A1 - Schönhals, Andreas A1 - Schartel, Bernhard T1 - Dielectric Study of Molecular Mobility in Poly(propylene-graft-maleic anhydride)/Clay Nanocomposites N2 - Polymer/clay nanocomposite materials based on poly(propylene-graft-maleic anhydride) (PPgMAH) and two different organophilic modified clays were investigated by dielectric relaxation spectroscopy (DRS). In contrast to ungrafted polypropylene (PP), PPgMAH shows a dielectrically active relaxation process which can be assigned to localized fluctuations of the polar maleic anhydride groups. Its relaxation rate exhibits an unusual temperature dependence, which could be attributed to a redistribution of water molecules in the polymeric matrix. This is confirmed by a combination of Raman spectroscopy and thermogravimetric experiments (TGA) with real-time dielectric measurements under controlled atmospheres. In the nanocomposites this relaxation process is shifted to higher frequencies up to 3 orders of magnitude compared to the unfilled polymer. This indicates a significantly enhanced molecular mobility in the interfacial regions. In the nanocomposite materials a separate high-temperature process due to Maxwell-Wagner-Sillars (MWS) polarization was observed. The time constant of this MWS process can be correlated with characteristic length scales in nanocomposites and therefore provides additional information on dispersion and delamination/exfoliation of clay platelets in these materials. These properties also influence the diffusivity of the water molecules as revealed by real-time dielectric investigations. KW - Polymer clay nanocomposites KW - Molecular mobility KW - Dielectric relaxation spectroscopy PY - 2005 DO - https://doi.org/10.1021/ma048315c SN - 0024-9297 SN - 1520-5835 VL - 38 IS - 7 SP - 2764 EP - 2774 PB - American Chemical Society CY - Washington, DC AN - OPUS4-7281 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böhning, Martin A1 - Tidjani, Adams A1 - Wald, Oliver A1 - Brzezinka, Klaus-Werner A1 - Turky, Gamal A1 - Goering, Harald A1 - Schartel, Bernhard A1 - Schönhals, Andreas T1 - Dielectric and gas transport properties of polypropylene-clay nanocomposites T2 - Frühjahrstagung des Arbeitskreises Festkörperphysik bei der DPG CY - Regensburg, Germany DA - 2002-03-11 PY - 2002 SN - 0420-0195 SN - 0372-5448 SN - 0343-9216 IS - CPP 5.4 SP - 425 CY - Bad Honnef AN - OPUS4-2036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Gas transport and molecular mobility in polymer/POSS nanocomposites T2 - Euromembrane 2006 CY - Taormina, Italy DA - 2006-09-24 PY - 2006 AN - OPUS4-11214 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Investigation of swollen polymer/gas-systems: atomistic packing models based on experimental properties T2 - Frühjahrstagung der Deutschen Physikalischen Ges. / AKF Condensed Matter CY - Dresden, Germany DA - 2006-03-26 PY - 2006 AN - OPUS4-11316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Gas Transport and Molecular Mobility in Polymer Based Nanocomposite Systems T2 - 1st International Conference on Advanced Materials and their application, National Research Centre, Physics Division CY - Cairo, Egypt DA - 2005-12-12 PY - 2005 AN - OPUS4-10976 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Small Molecules in Polymers and Polymer based Nanocomposites - Molecular Probes for Material Characterization and Design T2 - Polydays 2004 (Berliner Polymerentage); Universität Potsdam, Campus "Am Neuen Palais" CY - Potsdam, Germany DA - 2004-10-04 PY - 2004 AN - OPUS4-7297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin A1 - Goering, Harald T1 - Preparation and Characterisation of Nanoscaled Nanostructured Materials T2 - Nanofair 2004 CY - Karlsruhe, Germany DA - 2004-11-22 PY - 2004 AN - OPUS4-7296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin A1 - Robertson, Daniela A1 - Schröder, Hartmut T1 - Autoclave testing: a new approach for the evaluation of oxidative long-term resistance of geosynthetics N2 - Oxidative long time resistance is essential for many polyolefin based products, especially if repair or exchange is not possible as encountered in many building and geotechnical applications. Current regulations and recommendations for geosynthetics cover mainly the needs of a maximum lifetime of 25 years, though many applications require longer lifetimes up to 100 years and more. Reliable testing of the long time oxidation resistance is complicated by the complex interplay of physicochemical processes and reactions in combination with the need of relatively short testing durations, usually not exceeding 12 months. Thus for conventional atmospheric oven testing, the use of temperatures higher than 100 °C is inevitable, making conclusive Arrhenius extrapolations often questionable. Practical assessments of oxidative durability consist of exposures under accelerated ageing conditions with subsequent characterization of exposed material samples with respect to their residual stabilization and/or their mechanical properties. The autoclave test combines exposures at elevated temperatures with higher oxygen pressures and is performed with material samples immersed in a well defined aqueous medium representing critical environments in geosynthetic applications and including extraction of additives. Under these conditions meaningful results can be obtained within reasonable testing durations at only moderately elevated temperatures up to 80 °C. Application of different physicochemical methods, such as tensile testing, OIT /HP-OIT and analysis of residual antioxidant content (ICOT), in order to determine the time dependent degradation behaviour, reveal valuable information about mechanisms and effectiveness of the used antioxidants. Corresponding results for exposures at different temperatures and oxygen pressures are the basis for a 3D-extrapolation in order to estimate the expected service life. Different empirical models are presented and discussed with respect to their practical impact. T2 - EuroGeo4, 4th European Geosynthetics Conference CY - Edinburgh, UK DA - 2008-09-07 KW - Ageing KW - Degradation KW - Geotextiles KW - Polyolefin KW - Polypropylene KW - Oxidative resistance KW - Lifetime prediction PY - 2008 IS - Paper 143 SP - 1 EP - 8 AN - OPUS4-18424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heuchel, M. A1 - Hölck, Ole A1 - Böhning, Martin A1 - Siegert, R. A1 - Hofmann, D. ED - Qi, Y. ED - H.E. Fang, ED - N. Reynolds, ED - Liu, Z.-K. T1 - Knowledge-based approach to gas sorption in glassy polymers by combining experimental and molecular simulation techniques N2 - We present a method which allows to calculate gas sorption in complex polymers where, as slow processes, gas induced plasticization and volume dilation are important factors. Since the relaxational swelling of the polymer matrix that is observed at elevated gas concentrations takes hours or days, the swelling process is orders of magnitudes too slow to simulate the respective molecular dynamics in reasonable time and effort. To address this apparent incompatibility of experiment and simulation, we use single representative reference states from experiment and construct atomistic packing models according to these specifications. Gas sorption of CO2 and CH4 was successfully calculated on polysulfone, a 6FDA-polyimide, and a polymer of intrinsic microporosity, PIM-1, at 308 K and pressures up to 50 bar. T2 - MRS Fall Meeting 2008 - Symposium W - Computational Materials Design via Multiscale Modeling CY - Boston, MA, USA DA - 2008-12-01 KW - Gas sorption KW - Molecular modelling KW - Simulation KW - Glassy polymers PY - 2009 DO - https://doi.org/10.1557/PROC-1130-W06-10 VL - 1130 SP - W06 EP - W10 AN - OPUS4-19106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Gas sorption in glassy polymers - Comparative characterization using experimental and molecular modeling techniques T2 - EUROMEMBRANE 2009 Conference CY - Montpellier, France DA - 2009-09-06 PY - 2009 AN - OPUS4-20018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böhning, Martin A1 - Hölck, Ole A1 - Heuchel, M. A1 - Hofmann, D. T1 - Characterization of gas sorption in glassy polymers combining experimental and molecular modeling techniques KW - Glassy Polymers KW - Gas Sorption KW - Molecular Modelling KW - Diffusion PY - 2008 SN - 0743-0515 VL - 98 SP - 875 EP - 876 PB - Division of Polymeric Materials Science and Engineering, American Chemical Society CY - Washington, DC AN - OPUS4-17485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Autoclave testing - a new approach for the evaluation of oxidative long-term resistance of geosynthetics T2 - 4th European Geosynthetics Conference CY - Edinburgh, Scotland DA - 2008-09-07 PY - 2008 AN - OPUS4-18295 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Gas transport in glassy polymers and PNCs - experiment, analysis, modeling of diffusion, sorption and dilation T2 - Workshop: Polymers, University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture, Laboratory for Non-Metals CY - Zagreb, Croatia DA - 2012-05-23 PY - 2012 AN - OPUS4-25969 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Gas transport in glassy polymers and PNCs - experiment, analysis, modeling of diffusion, sorption and dilation T2 - Workshop: Nanostructured and Nanocomposite Membranes for Gas und Vapour Separation CY - Cetraro, Italy DA - 2012-05-15 PY - 2012 AN - OPUS4-26631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Correlation of gas diffusivity and local chain mobility in polycarbonate/POSS nanocomposites as determined by broadband dielectric relaxation spectroscopy T2 - Euromembrane 2012 CY - London, England DA - 2012-09-23 PY - 2012 AN - OPUS4-26629 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Kinetic analysis of gas sorption and gas induced dilation and relaxation behaviour of PIM-1 compared to other glassy polymers T2 - Euromembrane 2012 CY - London, England DA - 2012-09-23 PY - 2012 AN - OPUS4-26630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Frasca, Daniele A1 - Schulze, Dietmar A1 - Wachtendorf, Volker A1 - Krafft, Bernd A1 - Morys, Michael A1 - Böhning, Martin A1 - Rybak, Thomas T1 - Multilayer graphene rubber nanocomposites N2 - Multilayer Graphene (MLG), a nanoparticle with a specific surface of BET = 250 m²/g and thus made of only approximately 10 graphene sheets, is proposed as a nanofiller for rubbers. When homogenously dispersed, it works at low loadings enabling the replacement of carbon black (CB), increase in efficiency, or reduction in filler concentration. Actually the appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing and mechanical properties of different rubbers, as shown for Chlorine-Isobutylene-Isoprene Rubber (CIIR), Nitrile-Butadiene Rubber (NBR), Natural Rubber (NR), and Styrene-Butadiene Rubber (SBR). A mere 3 phr of MLG tripled the Young’s modulus of CIIR, an effect equivalent to 20 phr of carbon black. Similar equivalents are observed for MLG/CB mixtures. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards fire behavior. The later shown by the reduction in heat release rate in the cone calorimeter. The higher the nanofiller concentration is (3 phr, 5 phr, and 10 phr was investigated), the greater the improvement in the properties of the nanocomposites. Moreover, the MLG nanocomposites improve stability of mechanical properties against weathering. An increase in UV-absorption as well as a pronounced radical scavenging are proposed and were proved experimentally. To sum up, MLG is interesting as a multifunctional nanofiller and seems to be quite ready for rubber development. T2 - TOP 2016, VIII International Conference on “Times of Polymers and Composites” CY - Naples, Italy DA - 19.06.2016 KW - Graphene KW - Nanocomposite KW - Rubber PY - 2016 SN - 978-0-7354-1390-0 DO - https://doi.org/10.1063/1.4949621 SN - 0094-243X SN - 1551-7616 VL - 1736 SP - 020046, 1 EP - 4 PB - AIP AN - OPUS4-36864 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konnertz, Nora A1 - Ding, Yi A1 - Harrison, W.J. A1 - Budd, P.M. A1 - Schönhals, Andreas A1 - Böhning, Martin T1 - Molecular mobility of the high performance membrane polymer PIM-1 as investigated by dielectric spectroscopy N2 - The increasing demand for energy efficient separation processes fosters the development of new high performance polymers as selective separation layers for membranes. PIM-1 is the archetypal representative of the class of polymers of intrinsic microporosity (PIM) which are considered most promising in this sector, especially for gas separations. Since their introduction, PIMs stimulated a vast amount of research in this field and meanwhile evolved to the state of the art in membrane technology for gas separation. The major obstacle for extending the practical membrane application is their strong tendency to physical aging. For the first time, investigations by broadband dielectric spectroscopy (BDS) addressing molecular dynamics and conductivity in PIM 1 are presented. As chain packing during film formation from the casting solution and physical aging are key factors determining the separation performance of PIMs as membrane materials, characterization of the molecular mobility in such materials as revealed by BDS will provide valuable information for further development and optimization. KW - PIM-1 KW - BDS broadband dielectric spectroscopy KW - Relaxation KW - Membrane PY - 2016 DO - https://doi.org/10.1021/acsmacrolett.6b00209 SN - 2161-1653 VL - 5 IS - 4 SP - 528 EP - 532 PB - ACS American Chemical Society CY - Washington, DC, USA AN - OPUS4-35798 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konnertz, Nora A1 - Böhning, Martin A1 - Schönhals, Andreas A1 - Ding, Yi T1 - Molecular mobility and gas transport properties of PIM-1 and nano composites based on PIM-1 and phenethylPOSS N2 - Polymers with intrinsic microporosity are of highly interest in the field of gas separation membranes. Especially the first synthesized PIM-1 shows extraordinary permeabilities and selectivities. Unfortunately, PIM-1 tends to physical aging and loses its good properties. Physical aging is related to the molecular mobility of PIM-1 which was here investigated by broadband dielectric spectroscopy (BDS). Besides the studies on pure PIM-1 a polyhedral oligomeric silsesquioxane with phenethyl substituents (PhenethylPOSS) was used as nanofiller (0 - 40 wt-%) in the PIM-1 matrix to improve the gas transport properties and prevent physical aging. The molecular mobility of the solution casted nano composite films was analyzed by BDS as well. Furthermore, gas transport properties were determined with the time lag method (0 - 20 bar) in a temperature range of 35°C to 65°C with N2, O2, CH4 and CO2. T2 - 80. Jahrestagung der DPG und DPG-Frühjahrstagung CY - Regensburg, Germany DA - 06.03.2016 KW - PIM-1 PY - 2016 AN - OPUS4-35541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niebergall, Ute A1 - Zanotto, M. A1 - Wachtendorf, Volker A1 - Böhning, Martin T1 - Impact of biodiesel sorption on tensile properties of PE-HD for container applications N2 - In previous papers, we investigated the influence of biodiesel or diesel on mechanical properties of a high-density polyethylene (PE-HD) for tank applications using Charpy impact tests and dynamicmechanical analysis (DMA). In this work, covering two more PE-HD materials, we extend our study to addressing the tensile properties, especially changes of Young's modulus, after immersion in biodiesel or diesel at 60 °C. As we cover sorption and desorption behavior, during desorption, i.e. storage at 60 °C in a circulating air oven, ageing or degradation phenomena were also observed and characterized in some detail using spectral reflectance measurements and FT-IR spectroscopy. The results obtained here support the concept of co-oxidation, i.e. the faster oxidation of the PE-HD matrix if the samples were previously saturated with biodiesel, itself easily oxidizable. KW - polyethylene KW - biodiesel KW - biofuels KW - sorption KW - plasticization KW - degradation PY - 2016 DO - https://doi.org/10.1016/j.polymertesting.2016.01.025 SN - 0142-9418 VL - 50 SP - 315 EP - 324 PB - Elsevier AN - OPUS4-35369 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Agroui, K. A1 - Collins, G. A1 - Oreski, G. A1 - Böhning, Martin A1 - Hadj Arab, A. A1 - Ouadjaout, D. T1 - Effect of crosslinking on EVA-based encapsulant properties during photovoltaic module fabrication process N2 - The key objective of this work is to create a comprehensive comparison between experimental analysis methods for detecting crosslinking reaction in EVA encapsulant material during PV module fabrication process. Several analytical methods, spanning from classical gel content extraction measurements over different thermo-analytic and mechanical approaches to spectroscopic analysis as Thermally Stimulated Current (TSC), have been investigated as to their ability to reveal the crosslinking state of ethylene vinyl acetate (EVA). The basic results show that TSC complements perfectly other thermal analysis methods like as Differential Scanning Calorimetry (DSC), Dynamic Mechanical Thermal Analysis (DMTA) to determine fundamental properties of EVA such as molecular mobility characteristics and also to monitor the crosslinking reaction. Exothermic peak as revealed by DSC analysis can be used to estimate the crosslinking rate of EVA during PV module encapsulation process as fast quality control test. ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ L'objectif principal de ce travail est de permettre une meilleure compréhension entre les différentes techniques analyses expérimentales pour détecter la réaction de réticulation au niveau de l’encapsulant Ethylène-Vinyle Acétate (EVA), durant le process de fabrication d'un module PV. Plusieurs méthodes d'analyse, allant du test classique d'extraction du taux de gel aux différentes techniques d'analyses thermomécaniques ainsi que les techniques d'analyse de spectroscopie comme le courant stimulé thermiquement (TSC), ont été étudiés pour permettre de révéler le phénomène de la réaction de réticulation de l'encapsulant l'EVA. Les résultats de base montrent que la TSC complète parfaitement d'autres méthodes d'analyses thermiques comme la calorimétrie différentielle à balayage (DSC), l'analyse mécanique dynamique (DMTA) pour déterminer les propriétés fondamentales de l'EVA. Ces techniques permettent de déterminer les caractéristiques relatives à la mobilité moléculaire et aussi pour mieux mettre en évidence la réaction de réticulation. Le pic exothermique comme révélé par l'analyse par DSC, peut être utilisé pour estimer le taux de réticulation de l'EVA au cours du process d'encapsulation du module PV comme un test rapide de contrôle de qualité. KW - EVA KW - Photovoltaic module KW - Crosslinking process KW - Thermal properties KW - Mechanical properties PY - 2015 SN - 1112-2242 VL - 18 IS - 2 SP - 303 EP - 314 AN - OPUS4-34994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Yin, Huajie A1 - Lohstroh, W. A1 - Harrison, W. A1 - Budd, P.M. A1 - Pauw, Brian Richard A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Anomalies in the low frequency vibrational density of states for a polymer with intrinsic microporosity - the Boson peak of PIM-1 N2 - Polymers with intrinsic microporosity are promising candidates for the active separation layer in gas separation membranes. Here, the vibrational density of states (VDOS) for PIM-1, the prototypical polymer with intrinsic microporosity, is investigated by means of inelastic neutron scattering. The results are compared to data measured for a more conventional high-performance polyimide used in gas separation membranes (Matrimid). The measured data show the characteristic low frequency excess contribution to VDOS above the Debye sound wave level, generally known as the Boson peak in glass-forming materials. In comparison to the Boson peak of Matrimid, that of PIM-1 is shifted to lower frequencies. This shift is discussed considering the microporous, sponge-like structure of PIM-1 as providing a higher compressibility at the molecular scale than for conventional polymers. For an annealed PIM-1 sample, the Boson peak shifts to higher frequencies in comparison to the un-annealed sample. These changes in the VDOS of the annealed PIM-1 sample are related to changes in the microporous structure as confirmed by X-ray scattering. KW - Polymers KW - Boson peak KW - Neutron scattering KW - Physical aging KW - Polymer of intrinsic microporosity PY - 2018 DO - https://doi.org/10.1039/C7CP07141H SN - 1463-9076 SN - 1463-9084 VL - 20 IS - 3 SP - 1355 EP - 1363 PB - The Royal Society of Chemistry AN - OPUS4-43808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Chua, Y. Z. A1 - Yang, B. A1 - Schick, C. A1 - Harrison, W. A1 - Budd, P. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - First clear cut experimental evidence for a glass transition in a polymer with intrinsic microporosity: PIM-1 N2 - Polymers with intrinsic microporosity (PIMs) represent a novel, innovative class of materials with great potential in various applications from high-performance gas separation membranes to electronic devices. Here for the first time, for PIM-1, as the archetypal PIM, fast scanning calorimetry provides definitive evidence for a glass transition (Tg=715 K, heating rate 3·10^4 K/s) by decoupling the time-scales responsible for glass transition and decomposition. As the rigid molecular structure of PIM-1 prevents any conformational changes, small-scale bend and flex fluctuations must be considered the origin of its glass transition. This result has strong implications for the fundamental understanding of the glass transition and for the physical aging of PIMs and other complex polymers, both topical problems of materials science. KW - Polymers with intrinsic microporosity KW - Fast Scanning Calorimetry PY - 2018 DO - https://doi.org/10.1021/acs.jpclett.8b00422 SN - 1948-7185 VL - 9 IS - 8 SP - 2003 EP - 2008 PB - ACS AN - OPUS4-44683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thuy, Maximilian A1 - Niebergall, Ute A1 - Oehler, H. A1 - Alig, I. A1 - Böhning, Martin T1 - Evaluation of the damaging effect of crop protection formulations on high density polyethylene using the Full Notch Creep Test N2 - Four typical high-density polyethylene container materials were used to investigate damage or stress cracking behavior in contact with model liquids for crop protection products. These model liquids are established in German regulations for the approval of dangerous goods containers and consist of typical admixtures used for crop protection products but without biological active ingredients. This study is performed with the standardized method of Full Notch Creep Test, adapting the media temperature to 40 °C according to the usual conditions where these test liquids are applied. The two model liquids differ into a water-based solution and a composition based on different organic solvents which are absorbed by the material up to significant levels. Therefore, extensive sorption measurements are performed. The fracture surfaces obtained are analyzed in detail not only by light microscopy, but also by laser scanning microscopy as well as scanning electron microscopy. Influence of pre-saturation and applied stress are addressed by respective systematic series of experiments. KW - Polyethylene KW - Full Notch Creep Test KW - Environmental Stress Cracking KW - Fracture PY - 2021 DO - https://doi.org/10.1016/j.polymer.2021.123853 SN - 0032-3861 VL - 228 SP - 123853 PB - Elsevier Ltd. AN - OPUS4-52686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Environmental Stress Cracking in PE-HD – Assessment of Crack Propagation and Mechanisms by Optical Methods N2 - Slow crack growth (SCG) under the influence of external fluid media, usually termed environmental stress cracking (ESC), is still one of the most frequent origins of severe damage and failure of polymeric materials. For polyethylene (PE) this is relevant for mass products, like bottles for consumer products, but also for high-performance materials for pipes or industrial packaging, including containers for chemicals and other dangerous goods. Especially for high-density polyethylene (PE-HD) the susceptibility to SGC and ESC is depending on the complex interplay between molecular weight and architecture and the resulting semicrystalline morphology, especially the formation of tie-molecules. A reliable assessment of the resistance against this damage phenomenon is essential for demanding as well as safety-critical applications and has to take into account suitable testing methodologies and conditions in combination with environmental media reflecting the properties representative for typical fillings and relevant components causing ESC. In this context a better understanding of different influencing factors, such as sorption, swelling or surface activity is necessary together with a detailed characterization of different stages of crack propagation and underlying mechanisms. Therefor well-established testing methods, such as the Full Notch Creep Test (FNCT), were complemented by detailed fracture surface analysis using e.g. LSM and SEM in combination with a time-dependent optical monitoring of the progressing crack growth. For the crack growth also the ratio of fibrillated craze zone to crack opening is important for the deeper understanding of crack propagation and related material parameters which can be additionally addressed by X-ray computed tomography. T2 - 34th Polymer Degradation Disscussion Group (PDDG) Conference CY - Dubrovnik, Croatia DA - 12.06.2023 KW - Polyethylen KW - Full Notch Creep Test KW - Environmental Stress Cracking KW - Fracture Surface Analysis PY - 2023 AN - OPUS4-57711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -