TY - JOUR A1 - Ávila Calderón, Luis A1 - Rehmer, Birgit A1 - Schriever, Sina A1 - Ulbricht, Alexander A1 - Agudo Jácome, Leonardo A1 - Sommer, Konstantin A1 - Mohr, Gunther A1 - Skrotzki, Birgit A1 - Evans, Alexander T1 - Creep and creep damage behavior of stainless steel 316L manufactured by laser powder bed fusion N2 - This study presents a thorough characterization of the creep properties of austenitic stainless steel 316L produced by laser powder bed fusion (LPBF 316L) contributing to the sparse available data to date. Experimental results (mechanical tests, microscopy, X-ray computed tomography) concerning the creep deformation and damage mechanisms are presented and discussed. The tested LPBF material exhibits a low defect population, which allows for the isolation and improved understanding of the effect of other typical aspects of an LPBF microstructure on the creep behavior. As a benchmark to assess the material properties of the LPBF 316L, a conventionally manufactured variant of 316L was also tested. To characterize the creep properties, hot tensile tests and constant force creep tests at 600 °C and 650 °C are performed. The creep stress exponents of the LPBF material are smaller than that of the conventional variant. The primary and secondary creep stages and the times to rupture of the LPBF material are shorter than the hot rolled 316L. Overall the creep damage is more extensive in the LPBF material. The creep damage of the LPBF material is overall mainly intergranular. It is presumably caused and accelerated by both the appearance of precipitates at the grain boundaries and the unfavorable orientation of the grain boundaries. Neither the melt pool boundaries nor entrapped gas pores show a significant influence on the creep damage mechanism. KW - 316L KW - Laser Powder Bed Fusion (LPBF) KW - Creep behavior KW - Additive Manufacturing KW - AGIL PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-539373 DO - https://doi.org/10.1016/j.msea.2021.142223 SN - 0921-5093 VL - 830 SP - 142223 PB - Elsevier B.V. AN - OPUS4-53937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avila Calderon, Luis Alexander T1 - On the role of the manufacturing-induced cell structure in laser-powder-bed-fused stainless steel 316L during cyclic plastic deformation N2 - The room temperature cyclic plastic deformation behavior of stainless steel 316L produced by laser powder bed fusion and heat treated to two microstructural conditions was investigated in strain-controlled incremental-step-test low-cycle fatigue experiments. The heat treatments were performed at 450 °C for 4 h and at 900 °C for 1 h. The lower temperature heat treatment retains the cell structure present in the as-built material. The higher temperature heat treatment leads to disappearance of the cell structure and a decreased proof strength. Both investigated heat treatment conditions exhibited cyclic softening. In the condition heat treated at 900 °C for 1 h, the ability of the cell structure to act as barrier against plastic deformation when cyclically strained is degraded, which is reflected in the reduction of the cyclic yield strength. In that same condition, the cyclic softening was less pronounced. The presence or absence of the manufacturing-induced cell structure seems to determine the slip mode. When present, the microstructural evidence points to a planar slip behavior. After heat treatment at 900 °C for 1 h, which led to its dissolution, microstructural investigations revealed a wavy slip behavior, which has been also reported for the conventionally manufactured 316L counterpart [1]. In this case, the formation of low-energy dislocation structures acts as softening agent. T2 - Additive Manufacturing 2026 CY - Kassel, Germany DA - 25.03.2026 KW - AGIL KW - Additive Fertigung KW - Low-Cycle-Fatigue KW - 316L KW - Mikrostruktur PY - 2026 AN - OPUS4-65746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -