TY - JOUR A1 - Santandrea, A. A1 - Vignes, A. A1 - Krietsch, Arne A1 - Brunello, D. A1 - Perrin, L. A1 - Laurent, A. A1 - Dufaud, O. T1 - Evaluating the explosion severity of nanopowders: International standards versus reality N2 - The maximum explosion overpressure and the maximum rate of pressure rise, which characterize thedust explosion severity, are commonly measured in apparatuses and under specific conditions defined byinternational standards. However, those standards conditions, designed for micropowders, may not befully adapted to nanoparticles. Investigations were conducted on different nanopowders (nanocellulose,carbon black, aluminum) to illustrate their specific behaviors and highlight the potential inadequacyof the standards. The influence of the sample preparation was explored. Various testing procedureswere compared, focusing on the dust cloud turbulence and homogeneity. Dust dispersion experimentsevidenced the importance of the characterization of the dust cloud after dispersion, due to the frag-mentation of agglomerates, using metrics relevant with nanoparticles reactivity (e.g. surface diameterinstead of volume diameter). Moreover, the overdriving phenomenon (when the experimental resultsbecome dependent of the ignition energy), already identified for micropowders, can be exacerbated fornanoparticles due to their low minimum ignition energy and to the high energy used under standardconditions. It was evidenced that for highly sensitive nanopowders, pre-ignition phenomenon can occur.Finally, during severe explosions and due to a too long opening delay of the ‘fast acting valve’, the flamecan go back to the dust container. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.psep.2020.04.011 VL - 138 SP - 279 EP - 291 PB - Elsevier B.V. AN - OPUS4-50944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Nanoskalig hergestellte Materialien - Neueste Erkenntnisse T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen DA - 2015-11-05 PY - 2015 AN - OPUS4-34788 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Brand- und Explosionsgefahren von nanoskaligen Metallstäuben T2 - Jahrestreffen der ProcessNet-Fachgruppe "Agglomerations- und Schüttguttechnik" mit Beteiligung der Fachgemeinschaft "Anlagen- und Prozesssicherheit" CY - Magdeburg, Germany DA - 2014-03-10 PY - 2014 AN - OPUS4-30445 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Dörfel, Ilona A1 - Steinborn, Gabriele A1 - Langner, Jeanette A1 - Krietsch, Arne A1 - Seeger, Stefan A1 - Österle, Werner A1 - Schmidt, Martin A1 - Bresch, Harald T1 - Dossier on titanium dioxide - Part 1/1 - NM 105 N2 - In November 2007, OECD’s Working Party on Manufactured Nanomaterials (WPMN) launched the Sponsorship Programme for the Testing of Manufactured Nanomaterials (hereafter the Testing Programme). The objective was to conduct specific tests, relevant to human health and environmental safety endpoints, on a variety of manufactured nanomaterials (MN). The outcomes of the Testing Programme were intended to assess the applicability of the existing test guidelines1 to nanomaterials, as well as to provide useful information on any intrinsic properties of MNs, which are different from the same bulk material with greater external dimensions. Understanding the properties of NMs is crucial to choose appropriate strategies for hazard identification, risk assessment or risk management measures. The Testing Programme involved delegations from OECD member countries, some non-member economies and other stakeholders. The broad international representation, from a range of delegations enabled the programme to pool expertise and resources without which this programme would not have been possible. KW - Nanomaterial KW - Nanoparticle KW - Sponsorship programme KW - Nano characterization PY - 2015 UR - http://www.oecd.org/env/ehs/nanosafety/dossier-on-silver-nanoparticles-part1-1.htm IS - 54 SP - 27 CY - Paris AN - OPUS4-35430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhao, P. A1 - Schmidt, Martin A1 - Krause, U. A1 - Duan, Q. A1 - Krietsch, Arne A1 - Wu, Dejian T1 - Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction, inert gas and CH4 addition N2 - The explosion characteristics of anthracite coal dust with/without small amount of CH4 (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (Pex) and the rate of explosion pressure rise ((dp/dt)ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N2 with CO2, suggesting that CO2 has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH4 moderates the inhibition effect of CO2 and the promotion effect of O2 on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH4 mixture explosions, Barknecht’s curve was found to be more accurate and conservative than Chatelier’s line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries. KW - Lower explosion limit KW - Minimun explosion concentration KW - Explosion charasteristics KW - Hybrid mixture KW - Explosion regimes PY - 2021 DO - https://doi.org/10.1016/j.jlp.2021.104490 VL - 2021 SP - 1 EP - 10 PB - Elsevier Ltd. ET - 71 AN - OPUS4-54074 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, D. A1 - Abbas, Z. A1 - Krause, U. T1 - Ignition temperatures and flame velocities of metallic nanomaterials N2 - The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powd ers (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples. KW - Dust explosions KW - Nanomaterial KW - Flame propagation KW - Minimum ignition temperature PY - 2021 DO - https://doi.org/10.1016/j.jlp.2021.104482 SN - 0950-4230 VL - 2021 IS - 71 SP - 1 EP - 9 PB - Elsevier Ltd. AN - OPUS4-54076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abbas, Z. A1 - Gabel, D. A1 - Krietsch, Arne A1 - Krause, U. T1 - Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures N2 - Knowledge of explosion limiting concentration of explosible materials is necessary forthe design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptionsand possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new setup operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion. KW - Dust explosions KW - Gas explosions KW - Lower explosion limit KW - Hybrid mixtures PY - 2022 DO - https://doi.org/10.1016/j.jlp.2021.104640 SN - 0950-4230 VL - 74 SP - 1 EP - 18 PB - Elsevier Ltd. AN - OPUS4-54077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, D. A1 - Abbas, Z. A1 - Krause, U. T1 - Ignition temperatures and flame velocities of metallic nanomaterials N2 - The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powders (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2021 KW - Dust explosions KW - Nanomaterial KW - Flame propagation KW - Minimum ignition temperature PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540930 DO - https://doi.org/10.7795/810.20200724 SP - 591 EP - 605 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Krause, U. A1 - Gabel, D. A1 - Abbas, Z. A1 - Dufaud, O. T1 - Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures N2 - Knowledge of explosion limiting concentration of explosible materials is necessary for the design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptions and possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new set-up operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2020 KW - Dust explosions KW - Gas explosions KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540955 DO - https://doi.org/10.7795/810.20200724 SP - 750 EP - 764 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Su, Bin A1 - Luo, Zhenmin A1 - Krietsch, Arne A1 - Wu, Dejian A1 - Wang, Tao A1 - Zhou, Shangyong A1 - Deng, Jun T1 - Quantitative investigation of explosion behavior and spectral radiant characteristics of free radicals for syngas/air mixtures N2 - The combustion characteristics and explosive hazard of syngas (H2/CO)/air mixtures are affected by its exact composition and equivalence ratios. In this paper, the explosion pressure and spectral radiant intensity of free radicals were quantitatively examined for syngas with different H2 proportions ([H2 in syngas] = 0, 30, 50, 70, 100 vol%) and equivalence ratios (φ = 0.8, 1.0, 1.2, 1.4, 1.6, 2.0, 2.5). The results show that the explosion process of syngas/air mixtures can be separated into the initial slow combustion stage, the violent deflagration stage and the deflagration ending stage. The peaks of explosion pressure, pressure rise rate, OH*spectral intensity and rise rate of spectral intensity first increase and then decrease with increasing the equivalence ratio, and they reduce gradually with the decrease of H2 proportion in syngas. The H2 content in syngas greatly affects the heat release and the concentration of excited state OH*, especially for the syngas/air mixtures with smaller proportion of H2. Additionally, the presence of H2 greatly increases the deflagration index and spectral radiant index of OH* for syngas/air mixtures. The average rise rates of explosion pressure and spectral intensity of free radicals are introduced and the coupling model between them is established based on the first law of thermodynamics and the principle of chain reaction. The established model is furthermore verified by the experimental results. It is indicated that there is a linear relationship between average rise rates of explosion pressure and spectral intensity (OH*). The results can be used to improve the combustion efficiency of syngas and to guide theoretically the prevention, mitigation and control of syngas explosions. KW - Syngas KW - Hydrogen KW - Explosion pressure KW - Free radicals KW - Spectral intensity PY - 2024 DO - https://doi.org/10.1016/j.ijhydene.2023.10.280 SN - 0360-3199 VL - 50 IS - Part A SP - 1359 EP - 1368 PB - Elsevier Ltd. AN - OPUS4-59482 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Schmidt, Martin A1 - Krietsch, Arne A1 - Krause, U. T1 - Effect of oxygen concentration, inert gas and CH4/H2 addition on the minimum ignition energy of coal dusts N2 - MIKE III apparatus tests were conducted to investigate the minimum ignition energy (MIE) of coal dusts in air and O2/CO2 atmospheres with and without small amount of CH4/H2. The O2 mole fraction (XO2) in the gas mixtures varied from 21% to 50% with the CH4/H2 mole fraction from 0 to 2%. Experimental result showed that MIE of coal dusts significantly decreases even by three orders of magnitude in mJ with increasing XO2 and the addition of CH4/H2. Compared with CH4, H2 had a relatively strong promotion effect on the spark ignition of coal dusts. The inhibiting effect of CO2 was found to be much stronger than N2, but this inhibiting effect of CO2 could be eliminated by 9% increment of XO2. The effect on MIE of coal dusts thus followed by the order: 9% increment of XO2 > CO2 replacing N2 > 2% CH4 or H2 addition. Moreover, two empirical models were used to estimate the MIE of hybrid dust-gas mixture (HMIE), and the results showed that calculated data can well reflect the promoting effect of elevated XO2 and flammable gas addition, and the inhibiting effect of inert gas KW - Ignition energy KW - Hybrid mixture KW - Oxygen rich KW - Inerting effect KW - Empirical model PY - 2022 DO - https://doi.org/10.1016/j.jlp.2022.104772 SN - 0950-4230 VL - 77 SP - 1 EP - 10 PB - Elsevier Ltd. AN - OPUS4-55888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Verlauf der Explosionskenngrößen von Metallstäuben – von Mikro bis Nano N2 - Aufgrund von Erfahrungen mit Stäuben mit Partikelgrößen im Mikrometerbereich ist bekannt, dass Stoffe mit abnehmender Partikelgröße kritischer einzustufen sind, da z.B. maximaler Explosionsdruck (pmax), maximaler zeitlicher Druckanstieg (dp/dtmax) und Zündempfindlichkeit durch die Zunahme der reaktiven Oberfläche des Staubes zunehmen. Eine Übersicht des Verlaufes der Explosionsauswirkungen metallischer Stäube vom Mikrometerbereich bis in den Nanometerbereich konnte bislang nur vereinzelt durch wenige Ergebnisse gegeben werden. Dieser Beitrag präsentiert einen detaillierten Überblick über das Explosionsverhalten von Metallstäuben vom Mikrometer- bis in den Nanometerbereich. Hierfür wurden verschiedene Metallstäube untersucht und deren Explosionsauswirkungen in Abhängigkeit der mittleren Primärteilchengröße entweder durch BET-Messungen, Partikelgrößenverteilung oder REM-Mikroskopie bestimmt. Um den Verlauf des Explosionsverhaltens für diese Metalle darzustellen, wurde einerseits eine umfangreiche Literaturrecherche durchgeführt. Darüber hinaus wurden die im Rahmen deutscher und französischer Forschungsprogramme durchgeführten experimentellen Untersuchungen genutzt, um insbesondere die Datenlage für nanoskalig hergestellte Stäube zu verbessern. Auch bei Metallstäuben im Allgemeinen führt eine Verringerung der Teilchengröße zu einem kritischeren Verhalten der Stäube. Es scheint jedoch, dass diese Aussage nur bis zu einem kritischen Durchmesser gilt, unterhalb dessen die Auswirkungen einer Explosion (pmax, dp/dtmax) für alle betrachteten Stäube wieder abnehmen. Diese kritische Größe kann durch theoretische Überlegungen zur Art der thermischen Übertragung in der Flamme erklärt werden. Der Einfluss der Schlüsselparameter wird in diesem Beitrag ebenfalls diskutiert, um die Mechanismen besser zu verstehen und das Verständnis letztendlich auch auf andere pulverförmige Materialien auszudehnen. T2 - 13. Fachtagung "Anlagen-, Arbeits- und Umweltsicherheit" CY - Köthen, Germany DA - 16.11.2017 KW - Staubexplosion KW - Brennbare Stäube KW - Metallstäube KW - Nanomaterialien PY - 2017 AN - OPUS4-43510 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Schmidt, Martin T1 - Brand- und Explosionsgefahren von Nanomaterialien N2 - Nanotechnologie gilt als die Wachstumsbranche der nächsten Jahrzehnte. Nicht zuletzt ist diese Entwicklung den veränderten Eigenschaften der Materialien im Nanometerbereich zuzuschreiben. Das anders geartete Verhalten solcher Stoffe und die daraus ableitbare Unkenntnis über die Interaktion dieser Materialien mit ihrer Umgebung erfordert zur Risikoabschätzung eine intensive Auseinandersetzung mit der Thematik. Aufgrund von Erfahrungen mit Stäuben mit Partikelgrößen im Mikrometerbereich ist bekannt, dass Stoffe mit abnehmender Partikelgröße kritischer einzustufen sind, da ihre Explosionsheftigkeit und Zündempfindlichkeit durch die Zunahme der reaktiven Oberfläche des Staubs zunimmt. Nachfolgend werden Ergebnisse von Versuchen mit nanoskalig hergestellten Metallstäuben präsentiert. Der Fokus dieser Studie lag darauf, möglichst das kritischste Brand- und Explosionsverhalten solcher Stäube zu erfassen T2 - VDI-Fachtagung - Sichere Handhabung brennbarer Stäube CY - Nürnberg, Germany DA - 21.10.2014 KW - Brand- und Explosionsschutz KW - Nanostäube KW - Sicherheitstechnische Kenngrößen PY - 2014 SN - 978-3-18-092225-6 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 2225 SP - 17 EP - 32 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-31934 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krietsch, Arne A1 - Scheid, Marc A1 - Schmidt, Martin A1 - Krause, U. T1 - Explosion behaviour of metallic nano powders N2 - This paper describes experiences and results of experiments with several metallic dusts within the nanometer range. The nano dusts (aluminium, iron, zinc, titanium and copper) were tested in a modified experimental setup for the test apparatus 20 L-sphere (also known as 20-L Siwek Chamber), that enables the test samples to be kept under inert atmospheric conditions nearly until ignition. This setup was already introduced in earlier papers by the authors. It was designed to allow the determination of safety characteristics of nano powders under most critical circumstances (e.g. minimisation of the influence of oxidation before the test itself). Furthermore the influence of passivation on explosion behaviour is investigated and additional tests with deposited dust were carried out to describe the burning behaviour of all dusts. For a better characterisation all samples were tested with a simultaneous thermal analysis (STA). To minimise the influence of oxidation all samples were handled at inert conditions until shortly before ignition or start of the test respectively. KW - Dust explosion KW - Nano powder KW - Ignition KW - Explosion protection PY - 2015 DO - https://doi.org/10.1016/j.jlp.2015.03.016 SN - 0950-4230 SN - 1873-3352 VL - 36 SP - 237 EP - 243 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-33026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - IGNITION AND EXPLOSION PROPERTIES OF DIFFERENT TYPES OF NANO-MATERIALS T2 - International Conference on Safe production and use of nanomaterials, Nanosafe 2014 CY - Grenoble, Frankreich DA - 2014-11-18 PY - 2014 AN - OPUS4-32114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Erkenntnisse zum Brand- und Explosionsverhalten nanoskalig hergestellter Materialien T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Nürnberg, Deutschland DA - 2014-10-21 PY - 2014 AN - OPUS4-32117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Burning and Explosion Properties of Metallic Nano Powders T2 - Hazards 24 CY - Edinburgh, Scotland DA - 2014-05-07 PY - 2014 AN - OPUS4-30692 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Scheid, Marc A1 - Schmidt, Martin A1 - Krause, U. T1 - Explosion behaviour of metallic nano powders N2 - This paper describes experiences and results of experiments with several metallic dusts within the nanometer range. The nano dusts (aluminium, iron, zinc, titanium and copper) were tested in a modified experimental setup for the test apparatus 20 L-sphere (also known as 20-L Siwek Chamber), that enables the test samples to be kept under inert atmospheric conditions nearly until ignition. This setup was already introduced in earlier papers by the authors. It was designed to allow the determination of safety characteristics of nano powders under most critical circumstances (e.g. minimisation of the influence of oxidation before the test itself). Furthermore the influence of passivation on explosion behaviour is investigated and additional tests with deposited dust were carried out to describe the burning behaviour of all dusts. For a better characterisation all samples were tested with a simultaneous thermal analysis (STA). To minimise the influence of oxidation all samples were handled at inert conditions until shortly before ignition or start of the test respectively. T2 - X ISHPMIE - 10th International symposium on hazards, prevention, and mitigation of industrial explosions CY - Bergen, Norway DA - 10.06.2014 KW - Dust explosion KW - Nano dust KW - Ignition KW - Explosion protection PY - 2014 SN - 978-82-999683-0-0 SP - 1475 EP - 1485 AN - OPUS4-30938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Brand- und Explosionsgefahren bei der Handhabung von Nanostäuben T2 - 61. Sitzung des Industriearbeiterkreises "Brennbare Stäube" CY - Ludwigshafen am Rhein, Germany DA - 2014-06-24 PY - 2014 AN - OPUS4-30926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne T1 - Explosion Behaviour of Metallic Nano Powders T2 - Tenth International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (X ISHPMIE) CY - Bergen, Norway DA - 2014-06-10 PY - 2014 AN - OPUS4-30927 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Kwangvitayanon, Yolada A1 - Schmidt, Martin A1 - Klippel, Alexander A1 - Schröder, Volkmar A1 - Scheid, M. T1 - Validation of the new ignition source 'exploding wire' for dust explosion testing in the 20-L-sphere N2 - The safety characteristics Maximum Explosion Pressure pniB, Maximum Explosion Pressure Rise (dp/dt)™* and Lower Explosion Limit LEL are determined in closed vessels such as the 20-L-sphere according to international Standards. Dust ignition is carried out using pyrotechnical igniters which are defined in the Standards. Due to various disadvantages of pyrotechnical igniters the need for alternative ignition sources arises again and again. Studies at the Federal Institute for Material Research and Testing (BAM) with ignition units which were able to generate ignition energies up to 2000 J showed that the so-called “exploding wire” or “fuse wire“ is suitable as an alternative ignition source. The paper presents further test results for the Validation of the exploding wire for the determination of Pm» and (dp/dt)mx in the 20-L-sphere. The tests were performed with a new ignition unit and improved electrodes which allowed ignition energies up to 10000 J. The paper also analyses propagation of flame and electrical arc on basis of high speed camera recordings. Turbulence measurements with a LDA System in the 20-L-sphere allowed investigation whether the activation of the ignition sources has an influence on the turbulence field generated during dust dispersion and whether the influence differs depending on the ignition source. T2 - Hazards 24 Symposium CY - Edinburgh, UK DA - 07.05.2014 KW - Dust explosion testing KW - Exploding wire KW - Explosion characteristics KW - Ignition source PY - 2014 SN - 978-0-85295-582-6 N1 - Serientitel: IChemE Symposium Series – Series title: IChemE Symposium Series VL - 159 SP - 1 EP - 7 AN - OPUS4-31145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -