TY - JOUR A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Gaal, Mate A1 - Kreutzbruck, Marc A1 - Erhard, Anton A1 - Bovtun, Viktor Petrovic T1 - Ferroelektret-Prüfköpfe für die zerstörungsfreie Prüfung mit Luftultraschall N2 - Für die luftgekoppelte Ultraschall-Prüfung wird der Prototyp eines neuartigen Prüfkopfes vorgestellt. Statt eines piezokeramischen Ultraschall-Wandlers mit einer λ/4-Anpassschicht wird eine Ferroelektret-Folie aus schaumförmigem Polypropylen eingesetzt. Durch die außerordentlich geringe akustische Impedanz der Folie reduzieren sich die Reflexionsverluste an den Grenzschichten zur Luft so stark, dass bei diesem Prüfkopf auf eine λ/4-Anpassschicht verzichtet werden kann. Außerdem ist die Folie hochspannungsfest. Sie konnte mit Spannungen von mehr als 3500 V angesteuert werden und erlaubte eine Vorspannung am Ultraschall-Wandler des Empfangsprüfkopfes von 2000 V. Mithilfe der hohen Anregungsspannung stieg die Amplitude des akustischen Prüfimpulses auf das 11,2-Fache. Die Empfindlichkeit des Empfängers erhöhte sich durch die Vorspannung weiter um den Faktor 4,3. Insgesamt steigt die Amplitude am Empfänger also auf das 48-Fache, bei gleichbleibendem Rauschpegel. Ein abschließender Vergleich mit kommerziellen Luftultraschall-Prüfköpfen belegt die Überlegenheit der Folien-Prüfköpfe. Damit rückt der Einsatz einer vollwertigen Impuls-Echo-Technik auch bei der luftgekoppelten Ultraschallprüfung deutlich näher. KW - Prüfkopf KW - Ferroelektret KW - Luftultraschall KW - Zerstörungsfreie Prüfung PY - 2013 SN - 0025-5300 VL - 55 IS - 2 SP - 96 EP - 102 PB - Hanser CY - München AN - OPUS4-27778 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Erhard, Anton ED - Czichos, Horst T1 - Non-destructive evaluation N2 - Non-destructive testing (NDT) methods are employed in the technical field as a precautionary to avoid accidence or emergency situations for the human and the environment. A risk situation in the technical field could happen if the load of a component is increasing and the wall thickness due to defect growth is decreasing until a critical defect situation. The result of such scenarios could be catastrophic breakdown of the component with sometimes severe aftermath for the human. PY - 2013 SN - 978-3-642-25849-7 SN - 978-3-642-25850-3 DO - https://doi.org/10.1007/978-3-642-25850-3_9 IS - Chapter 9 SP - 161 EP - 174 PB - Springer CY - Berlin Heidelberg AN - OPUS4-27739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - ZfP als Basis für die Bewertung der Bauteilintegrität T2 - 200. Sitzung des Arbeitskreises Magdeburg CY - Magdeburg, Germany DA - 2013-03-06 PY - 2013 AN - OPUS4-27643 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Ultrasonic Inspection of Type B Packages T2 - 17th International Symposium on Packaging and Transportation of Radioactive Materials (PATRAM) 2013 CY - San Francisco, CA, USA DA - 2013-08-18 PY - 2013 AN - OPUS4-28704 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Overview about BAM T2 - Workshop mit SANDIA National Laboratories CY - Albuquerque, NM, USA DA - 2013-04-26 PY - 2013 AN - OPUS4-28275 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Comparison of Pre- and In-Service Inspection Techniques in Belgium and Germany against the backdrop of Ultrasonic Indications found at the Reactor Pressure Vessel of Doel-3 N2 - The Belgian Federal Agency for Nuclear Control (FANC) informed the public in August 2012 about the finding of thousands of flaws in the core area of the reactor pressure vessel of the nuclear power plant Doel-3. This information also prompted activities in Germany. The relation to Germany was very close, since the ingots of the forged rings came from Germany. That is why questions have arisen concerning quality management during fabrication: heat treatment, pre-service inspection in general, and NDT methods in particular. The focus will be on the rules and standards at the time of fabrication in relation to the required NDT methods and their failure sensibility levels. In addition, NDT registration levels and documentation and acceptance criteria at that time are also of interest. In the German Nuclear Safety Standard KTA, it is required that the employed NDT method is based on the state-of-the-art of science and technology. After having obtained the knowledge of the flaw situation in Doel-3, the discussion regarding the inspection areas for in-service inspection of the reactor pressure vessel rose up in Germany: Is it still enough to examine only the welds, including the head affected zones, or is it necessary to examine the whole rings, i.e. including the base metal? This paper will try to give answers to these questions in the light of the standards used in Germany. In addition, the information and experiences gained from pre-service inspection as well as many inservice inspections - which are required to be carried out every 4 to 5 years – will be described. T2 - 10th International Conference on NDE in relation to Structural Integrity for Nuclear and Pressurized Components CY - Cannes, France DA - 01.10.2013 PY - 2013 AN - OPUS4-29488 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Zerstörungsfreie Prüfung und Bruchmechanik T2 - 185. Sitzung des Arbeitskreises Dresden der DGZfP CY - Dresden, Germany DA - 2013-11-28 PY - 2013 AN - OPUS4-29489 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tscharntke, Dirk A1 - Wüstenberg, Hermann A1 - Erhard, Anton T1 - Ultraschallprüfung an Schweißnähten - Bewertung kritischer Befunde mit Modellrechnungen KW - Ultraschallprüfung KW - Schweißnahtprüfung KW - Modellrechnungen PY - 2000 SN - 0025-5300 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 42 IS - 11-12 SP - 433 EP - 436 PB - Carl Hanser Verlag CY - München AN - OPUS4-1014 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wüstenberg, Hermann A1 - Erhard, Anton A1 - Neundorf, B. T1 - The role of NDT at the primary circuit in german nuclear power plants PY - 2000 SN - 0335-5004 VL - B SP - 35 EP - 39 PB - CIMAX CY - Noisy-le-Grand Cedex AN - OPUS4-1098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Schenk, Gottfried A1 - Hauser, Th. A1 - Völz, Uwe T1 - New applications using phased array techniques N2 - In general, the application of phased array techniques used to be limited to heavy components with large wall thicknesses, such as those in the nuclear power industry. With the improvement of the phased array equipment, including phased array search units, other application areas are now accessible for the phased array inspection technique, e.g. the inspection of turbine blade roots, weld inspection with a wall thickness ranging from 12 to 40 mm, inspection of aircraft components, inspection of spot welds and the inspection of concrete building components. The objective for the use of phased array techniques has not significantly changed since their first application, e.g. instant adjustment of the sound beam to the geometry of the test object by steering incidence angle, skew angle and/or sound field focusing. Because some new phased array technique applications are still in the experimental (laboratory) stage, this article will focus on some examples for practical, real-weld applications. PY - 2001 DO - https://doi.org/10.1016/S0029-5493(00)00419-2 SN - 0029-5493 SN - 1872-759X VL - 206 IS - 2-3 SP - 325 EP - 336 PB - North-Holland Publ. Co. CY - Amsterdam AN - OPUS4-1122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Erhard, Anton T1 - Automated ultrasonic inspection systems T2 - Meeting of NDT-Experts CY - Trest', Czech Republic DA - 2001-06-20 PY - 2001 SN - 80-2387263-X SP - 55 EP - 62 PB - Czech Society for Non-Destructive Testing CY - Trest' AN - OPUS4-1126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Schulz, Eduard A1 - Brekow, Gerhard A1 - Wüstenberg, Hermann A1 - Kreier, P. T1 - Critical Assessments of the TOFD Approach for Ultrasonic Weld Inspection N2 - Weld inspection using ultrasonic pulse-echo techniques needs high skilled operators especially if geometrical indications must be taken into consideration. A clear separation between geometrical indications and defects like cracks must be guaranteed. This requirement needs sensitive techniques like the 45(deg) shear wave technique using the mirror effect. Since more than twenty years the Time Of Flight Diffraction technique (TOFD) is still under discussion for defect sizing. But on the other hand the potential of the TOFD technique for defect detection is described in technical papers of manufacturers. The main task of examinations carried out at BAM was the comparison about the detectability of surface breaking cracks between the common methods and the TOFD approach. T2 - 7th European Conference on Non-Destructive Testing (ECNDT) CY - Copenhagen, Denmark DA - 1998-05-26 KW - Time of flight diffraction KW - TOFD KW - Ultrasonic weld PY - 2001 SP - AD 1 EP - 199 PB - Society of Manufacturing Engineers CY - Dearborn, Mich. AN - OPUS4-1105 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tessaro, Ute A1 - Wüstenberg, Hermann A1 - Erhard, Anton A1 - Boehm, Rainer T1 - Ultraschalluntersuchungen zur Fehlercharakterisierung im Plattierungsbereich T2 - Jahrestagung Zerstörungsfreie Materialprüfung ; 2001 (Berlin) : 2001.05.21-23 CY - Berlin, Deutschland DA - 2001-05-21 PY - 2001 UR - http://www.ndt.net/article/dgzfp01/papers/p09/p09.htm N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 75-CD PB - DGZfP CY - Berlin AN - OPUS4-1139 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brekow, Gerhard A1 - Erhard, Anton A1 - Schulz, Eduard A1 - Siebelmann, F. A1 - Kiechle, H. T1 - Optimierung der Ultraschall-Prüftechnik bei Engspaltschweißnähten T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2001 CY - Berlin, Deutschland DA - 2001-05-21 PY - 2001 UR - http://www.ndt.net/article/dgzfp01/papers/p08/p08.htm N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 75-CD PB - DGZfP CY - Berlin AN - OPUS4-1140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Eduard A1 - Erhard, Anton A1 - Montag, Hans-Joachim A1 - Beine, U. A1 - Lucht, B. T1 - Fehleranalyse an einer austenitischen Rohrschweißnaht T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2001 CY - Berlin, Deutschland DA - 2001-05-21 PY - 2001 UR - http://www.ndt.net/article/dgzfp01/papers/p10/p10.htm N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 75-CD PB - DGZfP CY - Berlin AN - OPUS4-1141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Bertus, Norbert A1 - Montag, Hans-Joachim A1 - Schenk, Gottfried A1 - Hintze, H. T1 - Ultrasonic Phased Array System for Railroad Axle Examination N2 - Introduction Due to the long history of railroad companies around the world, varying means of examination according to the specifications for the different railroad components have been carried out based on the general industrial progress of the country [1-3]. For more than 50 years the application of customized ultrasonic techniques for the examination of railroad components has increased, in comparison to conventional ultrasonic techniques used until to the end of 20th century. In this traditional atmosphere some accidents have disturbed the silent harmony of companies involved in the production of critical parts. More than ever high speed modern trains require modern and advanced examination techniques [4-8]. For practical application new ultrasonic techniques have been developed and optimized in co-operation with the German Railroad Company. In the present contribution the inspection of railroad axles will be described. The ultrasonic technique used for the examination is the phased array technique. The optimization of the phased array probes for the different geometries of the axles given was completed using a computer model for directivity calculations. In relation to the limited accessibility between wheel and brake angles of incidence for shear waves in the range between 28° and 72° are necessary. During the examination of the axles a a considerable amount of ultrasonic data must be stored (storage of the digitized A-scans). However, due to economic aspects the evaluation of this data should be carried out in a very short time. The whole examination of one axle should not exceed 5 minutes. Therefore we have developed a special evaluation program adapted to the particular problematic of the axle inspection. The build up of the whole inspection system was done with partners from the industry like Krautkramer and a division of the Research Department of the Deutsche Bahn AG. In this consortium the Research Department of the Deutsche Bahn AG was responsible for the specification of the inspection problem, Krautkramer for the organization of the whole technical follow up and BAM for the development and optimization of the ultrasonic inspection technique as well as for the evaluation software. Some examples concerning the optimization process will be described in the present contribution. T2 - 8th ECNDT CY - Barcelona, Spain DA - 2002-06-17 PY - 2002 UR - http://www.ndt.net/article/ecndt02/75/75.htm PB - European Federation for Non-Destructive Testing CY - Barcelona AN - OPUS4-1414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pohl, Rainer A1 - Erhard, Anton A1 - Montag, Hans-Joachim A1 - Thomas, Hans-Martin A1 - Wüstenberg, Hermann ED - Forde, M. C. T1 - NDT techniques for railroad wheel and gauge corner inspection T2 - 5th Railway Engineering Conference CY - London, England, UK DA - 2002-07-03 KW - Non-destructive testing method KW - Ultrasonic and eddy current techniques KW - Railway track and wheel inspection PY - 2002 SN - 0-947644-49-0 SP - 1 EP - 14(?) PB - Engineering Technics Press CY - Edingburgh AN - OPUS4-1561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Boehm, Rainer A1 - Tessaro, Ute A1 - Wüstenberg, Hermann T1 - Characterization and sizing of defects in the cladding area using ultrasonic methods T2 - 3rd International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components CY - Seville, Spain DA - 2001-11-14 PY - 2002 CY - Seville AN - OPUS4-1748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tessaro, Ute A1 - Erhard, Anton A1 - Brekow, Gerhard A1 - Mletzko, U. T1 - Charakterisierung oberflächennaher Fehler an plattierten Komponenten mittels Gruppenstrahlertechnik N2 - Zusammenfassung Nachdem Untersuchungen mit konventionellen Prüfköpfen an plattierten Bauteilen gezeigt haben, dass es möglich ist, mit Hilfe von Beugungsanzeigen bzw. -mustern die Größe und Tiefenlage von Fehlern im Plattierungsbereich zu bestimmen, wurde die Gruppenstrahlertechnik für Fehlersuche und -charakterisierung eingesetzt. Der Vorteil bei der Arbeit mit Gruppenstrahlerprüfköpfen besteht darin, dass in einer Messfahrt eine Reihe von Einschallwinkeln abgearbeitet werden kann. Dies vereinfacht und verkürzt die Prüfung wesentlich. So wurde von der ferritischen und der plattierten Seite der Testkörper mit der Impuls-Echo-Technik im halben Sprung, der TOFD-Technik und mit Sende-Empfangs-Prüfköpfen oberflächennah geprüft. Allerdings haben alle hier aufgeführten Verfahren ihre Grenzen, so sind z.B. Fehler, die eine Fehlergröße von £ 3 mm aufweisen, kaum noch zu charakterisieren. Hier ist nur der Nachweis möglich. Es hat sich außerdem gezeigt, dass die TOFD-Technik nur als Ergänzung zu anderen Techniken eingesetzt werden sollte, da das Potenzial für die Verwendung als Suchtechnik nicht ausreichend ist. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Fehlergrößenbestimmung KW - Gruppenstrahlerprüfköpfe KW - TOFD KW - Impuls-Echo-Technik KW - SEL-Prüfköpfe PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/p07/p07.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1850 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tscharntke, Dirk A1 - Boehm, Rainer A1 - Erhard, Anton A1 - Wüstenberg, Hermann T1 - Fehlerdiagnose in der Ultraschallprüfung mit iterativer Modellierung N2 - Zusammenfassung Die verschiedenen Bewertungs- und Untersuchungsverfahren zur Fehlerdiagnose in der Ultraschallprüfung lassen in Abhängigkeit von der Prüfsituation nur eine fallweise Anwendung zu. Die erzielbaren Ergebnisse sind durch prinzipielle Grenzen, wie die orientierungsabhängigen Wechselwirkungen der Ultraschallwellen mit dem Fehler, in ihrer Genauigkeit stark begrenzt. Im allgemeinen enthalten sie nur einen Teil der für eine belastbare Fehlerdiagnose erforderlichen Informationen. Eine zuverlässige Bewertung ist meist durch die Zusammenfassung der Ergebnisse redundanter US- Verfahren und die Nutzung von a priori Informationen, z.B. aus der Fertigungsgeschichte einer Komponente, möglich. Der Einsatz mehrerer US-Prüfverfahren bedingt üblicherweise einen höheren Zeit-, Arbeits- und Kostenbedarf und sollte möglichst durch Verbesserung der Fehlerdiagnose mit einem Verfahren begrenzt werden. Die im Beitrag vorgestellte iterative Modellierung der Ultraschallprüfung bietet dazu eine Möglichkeit. Die Durchführung der Modellrechnungen beginnt mit der Aufstellung einer Fehlerhypothese unter Einführung von a priori Informationen. Die Nachrechnung der Fehlerhypothesen mit dem validierten und erprobten Modell ermöglicht den Vergleich mit den Messergebnissen. Die aufgestellten Fehlerhypothesen können so abgesichert, sowie Messergebnisse überprüft und bestätigt werden. Das Rechenmodell ermöglicht die Bewertung der Amplitude, der Laufzeit, der Echodynamik und des Anzeigenmusters, also aller auch bei anderen Bewertungs- und Untersuchungsverfahren herangezogenen Bewertungsmaßstäbe. Eine Kombination des Rechenmodells mit einer Evolutionsstrategie würde die Systematisierung des Verfahrens ermöglichen, ist jedoch mit Schwierigkeiten verbunden, wie im Beitrag gezeigt wird. Die iterative Modellierung besteht aus drei Teilprozessen, der Analyse der möglichen Wechselwirkungen, der Separation dieser Wechselwirkungen in diverse Schallwege und schließlich der Synthese der auf den verschiedenen Wegen berechneten Signale zum Gesamtsignal. Die ersten beiden Teilprozesse müssen z.Zt. auf Basis von Expertenwissen für jeden Prüffall neu gelöst werden. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Pipelines KW - Schweißnahtprüfung KW - Gruppenstrahlertechnik KW - Real-Time-Scanner KW - Gruppenstrahler-Prüfkopf mit 64 Schwingerelementen KW - Konventionelle Winkelprüfköpfe PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/v54/v54.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brekow, Gerhard A1 - Erhard, Anton A1 - Schulz, Eduard A1 - Montag, Hans-Joachim A1 - Pörtzgen, N. T1 - BAM-RTD Phased Array Konzept für die Schweißnahtprüfung von Rohrleitungen N2 - Zusammenfassung Aus den Messergebnissen geht hervor, dass der Real-Time-Scanner den Reflektor-nachweis der konventionellen Prüfköpfe hinsichtlich des erreichten S/R-Abstandes erreicht und teilweise übertrifft. Weiterhin geht aus den Ergebnissen hervor, dass die Nachweisempfindlichkeit sehr empfindlich auf Abweichungen der Prüfkopf-positionierung reagiert. Nur wenn die optimale Fahrspur für jede Reflektortiefenlage getroffen wird, kann mit den konventionellen Prüfköpfen ein S/R-Abstand von mehr als 20 dB erreicht werden. Das bedeutet, dass mit den konventionellen Prüfköpfen immer mehrere parallele Fahrspuren mit kleinem Spurversatz gefahren werden müssen, um auch kleine Fehler in der Schweißnaht nachweisen zu können. Mit dem Real-Time-Scanner-Prüfkopf können mit einer einzigen Messfahrt und mit entsprechend vielen angepassten Messfunktionen mehrere parallele Fahrspuren durch elektronisch gesteuerte Bündelverschiebung erfasst werden. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Pipelines KW - Schweißnahtprüfung KW - Gruppenstrahlertechnik KW - Real-Time-Scanner KW - Gruppenstrahler-Prüfkopf mit 64 Schwingerelementen KW - Konventionelle Winkelprüfköpfe PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/p10/p10.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Erhard, Anton T1 - Untersuchungen zur Ausbreitung von Longitudinalwellen an Oberflächen bei der Materialprüfung mit Ultraschall N2 - Der Nachweis von Rissen an Oberflächen hat wegen der großen sicherheitstechnischen Relevanz dieses Bereiches auch in der zerstörungsfreien Materialprüfung mit Ultraschall an Bedeutung gewonnen. Mit der Beschreibung der Ausbreitung von Longitudinalwellen an der Oberfläche wurden der Effekt des streifenden Einfalls von LongitudinaIwellen und die Schallfeldverteilung von Longitudinalwellen-Winkelprüfköpfen im Nahfeld berechnet. T3 - BAM Forschungsberichtreihe - 88 KW - Ultraschallprüfung KW - Longitudinalwelle PY - 1983 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-3620 SN - 978-3-88314-254-9 SN - 0938-5533 VL - 88 SP - 1 EP - 42 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Schulz, Eduard T1 - Influences on crack detection in the near surface area with ultrasonic inspection techniques T2 - 29th Annual Conference of the Czech Society for Nondestructive Testing CY - Hradec Králové, Czech Republic DA - 1999-11-17 KW - Crack detection KW - Rißprüfung KW - Ultraschallprüfung PY - 1999 SP - 153 EP - 164 AN - OPUS4-717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Erhard, Anton A1 - Heß, G. A1 - Thumser, D. A1 - Engl, G. T1 - Schmiedewellenprüfung - Vergleich von manueller und mechanisierter Ultraschallprüfung N2 - Die Ultraschallprüfung von großen Schmiedewellenrohlingen für den Turbinen- und Generatorbau mit Durchmesser bis zu 2000 mm ist nach wie vor eine Herausforderung für die Ultraschallprüfung, weil kleinste "Fehlstellen" nachgewiesen werden müssen. So sind Registriergrenzen in der Größenordnung von 1 mm Kreisscheibe in Wellenmitte durchaus gängige Praxis. Die Prüfung dieser Schmiedeteile wird derzeit meist manuell durchgeführt. Eine mechanisierte Ultraschallprüfung hat den Vorteil einer dem Prüffortschritt angepaßten reproduzierbaren Dokumentation und der Speicherung der Meßdaten in Form von A-Bildern. Bei der Verwendung der Gruppenstrahlertechnik mit deren Möglichkeit der elektronischen Schallfeldsteuerung, wie Änderung des Einschallwinkels oder Fokussierung des Schallbündels, kann eine Ultraschallprüfung des gesamten Querschnitts schnell, ortsgenau reproduzierbar und zuverlässig durchgeführt werden. Durch Speicherung der A-Bilder in einem Pixelnetz können für die Auswertung der Meßwerte Tomogramme d.h. Schnittbilder Quasi-Online erstellt werden. Durch Übernahme der Meßdaten in ein CAD-Auswerte-programm können die Ergebnisse z.B. dr können die Ergebnisse z.B. dreidimensional ortsgetreu dargestellt werden. Ein Vergleich der unterschiedlichen Ultraschallprüfergebnisse zwischen manueller und mechanisierter Prüfung wird an einer Beispielwelle vorgestellt. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 1999 CY - Celle, Deutschland DA - 1999-05-10 KW - Ultraschallprüfung KW - Schiedestück KW - Schallfeld PY - 1999 UR - http://www.ndt.net/abstract/dgzfp99/data/53.htm SN - 3-931381-27-7 VL - 1 IS - 68 SP - 467 EP - 479 PB - DGZfP CY - Berlin AN - OPUS4-706 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Erhard, Anton A1 - Neundorf, B A1 - Hansch, M. A1 - Britz, A. T1 - Bewertung und Auswertung von Ultraschallmeßdaten - VGB-Auswerterichtlinie N2 - Zur Steigerung der Zuverlässigkeit in der Prüfaussage und zur Vermeidung von Fehlinterpretationen ist es sinnvoll, die Auswertung und Bewertung von Ultra-schall-meßdaten zu vereinheitlichen. Dies ist insbesondere bei der mechanisierten Ultraschallprüfung vereinheitlichen. Dies ist insbesondere bei der mechanisierten Ultraschallprüfung gefragt, denn durch die Vielzahl der Meßdaten, der unterschiedlichen Ultraschall-Gerätetechnik und der individuell angepaßten Soft-ware sind unterschiedliche Darstellungen der Ergebnisse möglich. Eine "Standardisierung" der Aus- und Bewertung ist somit nicht möglich. Ein Ziel der hier vorzustellenden Auswerterichtlinie ist deswegen eine Vereinheitlichung der Darstellung. In der Richtlinie werden Mindestanforderungen vorgeschrieben. In diesem Beitrag werden Beispiele für die verschiedenen Darstellungsarten und die Vorgehensweise bei der Bewertung von Amplitude, Laufzeit, Dynamik und Anzeigennmuster gezeigt. Ein weiteres Ziel der Richtlinie ist, die Auswertehilfen und Auswertetechniken so zu dokumentieren, daß der Weg, der zum Prüfergeb-nis führt, jederzeit nachvollziehbar ist. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 1999 CY - Celle, Deutschland DA - 1999-05-10 KW - Ultraschallmeßverfahren PY - 1999 UR - http://www.ndt.net/abstract/dgzfp99/data/58.htm SN - 3-931381-27-7 VL - 68 IS - 68 PB - DGZfP CY - Berlin AN - OPUS4-707 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brekow, Gerhard A1 - Erhard, Anton T1 - Untersuchungen mit TOFD an geschweißten Längsnahtproben N2 - Im Gegensatz zur Impuls-Echo-Technik, die im Wesentlichen auf der Anton Erhard, Berlin Reflexion am Fehler basiert, wird bei der Time-Of-Flight Diffraction Technique (TOFD-Technik) die Beugung der Schallwellen am Fehler zum Nachweis genutzt. Zwei Winkelprüfköpfe für Longitudinalwellen sind in V-Durchschallung angeordnet. Die Prüfköpfe befinden sich jeweils auf einer Seite der Schweißnaht und werden bei der Messung parallel zur Schweißnaht verschoben. Das ausgesandte Schallbündel trifft auf Fehlerränder, an denen gebeugte Wellenanteile entstehen, die je nach Entstehungsort mit unterschiedlichen Schalllaufzeiten empfangen, in hochfrequenten A-Bildern abgespeichert und für die Auswertung in B-Bildern dargestellt werden. Die Untersuchungen zeigen, dass die TOFD-Technik Beiträge zur Fehlergrößenabschätzung liefert, aber keinesfalls die Impuls-Echo- Technik mit nachgeschalteter Röntgenprüfung ersetzen kann. PY - 2000 SN - 0025-5300 VL - 42 IS - 11-12 SP - 437 EP - 443 PB - Carl Hanser Verlag CY - München AN - OPUS4-963 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Bäßler, Ralph A1 - Weltschev, Margit T1 - Regulating the use of new materials in containment systems for dangerous goods N2 - Transportation of dangerous goods are worldwide regulated in the rules or standards e.g. in the recommendations on the Transport of Dangerous Goods of the United Nations, in the Accord Européen Relatif au Transport International des Marchandises Dangereuses par Route (ADR) etc. Addi-tional to these international regulations also national regulations and stan-dards e.g. Gefahrgutverordnung Straße und Eisenbahn (GGVSE) in Ger-many are bases for the transport of hazardous materials. For the material properties of tanks in the “BAM-List – Requirements for Tanks for the Transport of Dangerous Goods” specifications for the sub-stance prototype approval for tank materials are listed. Further compati-bility evaluations of selected metallic material groups as well as of poly-meric gasket and lining materials under the influence of dangerous goods are published in the List. There are a large number of highly corrosive dangerous goods listed, in which conventional steels are not resistant. Chemical companies, transportation providers and tank producers need tanks made of corrosion-resistant materials (corrosion retardant materi-als) in order to protect the tank shell. The application of high-alloyed stainless steels and nickel alloys as there are alloy 926 (1.4529; X1NiCrMoCuN25-20-7), alloy 31 (1.4562;X1NiCrMoCu31-27-7) and Nickel-Chromium-Molybdenum Alloy 59 (2.4605; NiCr23Mo16Al) is an al-ternative solution compared with the lining of the tanks with a polymeric material. Due to the limited number of corrosion test results with welded test sam-ples of these high-alloyed materials under the influence of corrosive dan-gerous goods BAM, Institute for Corrosion Protection (IKS) Dresden and ThyssenKrupp VDM have been performing a comprehensive test program since 2002. The program comprised corrosion resistance evaluations of the three high-alloyed materials exposed to substances representing cor-rosive dangerous goods such as inorganic halogenides, organic acidic halogenides, sulfonic acids and nitrating acids. T2 - MRS Fall Meeting 2008 - Symposium SS -Selecting and Qualifying New Materials for Use in Regulated Industries CY - Boston, MA, USA DA - 2008-12-01 KW - Korrosionsbeständigkeit KW - Superaustenite KW - Nickellegierung KW - Gefahrguttransport PY - 2008 DO - https://doi.org/10.1557/PROC-1151-SS01-02 VL - 1151E IS - Paper #: 1151-SS01-02 SP - 1 EP - 8(?) CY - Warrendale, PA, USA AN - OPUS4-19610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tscharntke, Dirk A1 - Wüstenberg, Hermann A1 - Erhard, Anton T1 - Bewertung kritischer Befunde bei der Ultraschallprüfung an Schweißnähten mit Modellrechnungen N2 - Typische Probleme bei der Schweißnahtprüfung mit Ultrschall entstehen bei ferritischen Werkstoffen vor allem durch Anzeigen von der Nahtkontur, vor allem aus dem Wurzelbereich. Die klassischen Methoden der Unterscheidung formbedingter Anzeigen von Fehlern - z.B. durch Vergleich der A-Bilder von beiden Seten einer Stumpfnaht - können unterstützt werden durch die Modellierung derartiger Anzeigen im Zusammenhang mit hypothetischen Fehlern im wurzelnahen Bereich. Im Beitrag wird die Anwendung vereinfachender Modelle auf diese Problematik vorgestellt und an Beispielen demonstriert. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2000 CY - Innsbruck, Österreich DA - 2000-05-29 KW - Ultraschallprüfung KW - Schweißnahtprüfung KW - Modellrechnungen PY - 2000 UR - http://www.ndt.net/abstract/dgzfp00/data/10.htm SN - 3-931381-32-3 VL - 73-1 IS - 2 SP - 105 EP - 117 PB - DGZfP CY - Berlin AN - OPUS4-936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schulz, Eduard A1 - Erhard, Anton A1 - Heinrich, W. A1 - Mohr, F. T1 - Nachqualifikation einer Wasserreibbremse mit Ultraschall N2 - Neu entwickelte Gasturbinen werden im Prüffeld mit wechselnden Belastungen beaufschlagt. Dazu wird die Gasturbine mit einer Wasserreibbremse gekoppelt, mit der eine definierte Last erzeugt werden kann. Ursprünglich war die Wasserreibbremse für eine bestimmte Leistung, die den früheren Leistungen der Gasturbine entsprach, ausgelegt worden. Die erste Prüfung fand im Jahr 1975 statt. Da neuere Gasturbinen wesentlich höhere Leistungen erbringen und die vorhandene Wasserreibbremse weiterhin eingesetzt werden sollte, musste eine Nachqualifizierung vorgenommen werden. Das Ziel war die Absicherung auf eine mögliche Sprödbruchgefahr. Zunächst wurde eine Studie zur Prüfbarkeit erstellt. An speziellen Testkörpern wurden im Ultraschallabor der BAM Vorversuche zur Machbarkeit, zur Empfindlichkeitsein-stellung und zur Vorbereitung der Prüfung durchgeführt. Dazu wurden spezielle Gruppenstrahlerprüfköpfe gefertigt und ein an die komplizierte Geometrie der Bremsscheiben angepasster Manipulator gebaut. Ferner wurde, um die Prüfzeiten zu reduzieren, die Software zur Datenerfassung und zur Auswertung angepasst. Im Werk Berlin der Siemens AG wurde in Zusammenarbeit mit der Siemens AG Erlangen eine Ultraschallprüfung mit der Gruppenstahlertechnik der Wasserreibbremse durchgeführt. Überprüft wurde das gesamte Volumen auf axial, radial und tangential beanspruchte Fehler in den Bereichen der Welle und der Bremsscheibe.Die Überprüfung ergab keine relevanten Fehler, so dass die Wasserreibbremse weiterhin eingesetzt werden kann. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2000 CY - Innsbruck, Österreich DA - 2000-05-29 PY - 2000 UR - http://www.ndt.net/abstract/dgzfp00/data/79.htm SN - 3-931381-32-3 VL - 73 IS - 2 SP - 1(?) EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-940 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tscharntke, Dirk A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Erhard, Anton A1 - Krull, R. A1 - Lützner, J. A1 - Hintze, H. T1 - Development of in-service rail inspection systems using phased arrays PY - 2012 SN - 978-3-87155-608-1 SN - 1618-4513 VL - 4 SP - 182 EP - 187 PB - DVS Media GmbH CY - Düsseldorf ET - English Edition AN - OPUS4-26828 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Schenk, Gottfried A1 - Hauser, Th. A1 - Völz, Uwe ED - Roos, E. T1 - Anwendungsmöglichkeiten der Gruppenstrahlertechnik T2 - 25th MPA-seminar CY - Stuttgart, Germany DA - 1999-10-07 KW - Gruppenstrahlertechnik PY - 1999 VL - 206 IS - 2-3 SP - 25.1 EP - 25.10 PB - North-Holland CY - Amsterdam AN - OPUS4-796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Munikoti, Vijayendra K. A1 - Brekow, Gerhard A1 - Tessaro, Ute A1 - Erhard, Anton T1 - Ultrasonic inspection for transverse defects in dissimilar metal welds N2 - As a part ofthe cooling circuit in many nuclear power installations, dissimilar metals are welded together - for example, weid overlay cladding of austenitic material (either Inconel or 1.4550) on low alloy Steel. These welds are prone to stress corrosion Cracking. In some ofthe nuclear power stations, cracks were detected on the inner surface of the dissimilar weid. These cracks, which have their Orientation perpendicular to the weiding direction, are designated as transverse cracks. The purpose of the present investigation is to develop an ultrasonic testing method for reliable detection ofsuch transverse cracks. Very offen, crack detection and sizing in dissimilar welds with ultrasound can be very difficult due to the following reasons: 1. In a weiding process, high thermal gradients exist between the molten weid pool and the neighbouring colder regions. During the solidification process, grains grow along the direction of heat flow, yielding a textured structure. This results in a microstructure consisting of elongated grains, which causes the anisotropic nature of the weid region. An elastic wave in such an anisotropic medium undergoes beam skewing (i.e. phase and group velocity (Energy flow) directions are no longer coincident). 2. Due to the above mentioned grain structure, elastic properties vary spatially. This amounts to an ultrasonic wave undergoing multiple reflections at grain boundaries. The ray direction gets successively skewed at each grain boundary, resulting in a curved path. In addition to the grain boundaries, there are also interfaces between different parts ofthe dissimilar weid such as parent metal, transition layer, cladding and weid. At these interfaces, reflections and mode conversions occur in addition to scattering at grain boundaries. Altogether, ultrasonic inspection ofdissimilar welds for defect detection and sizing poses major challenges. Presently international research activities are concerned with the development of improved Signal Processing methods and optimizing strategies for qualifying ultrasonic inspection techniques for dissimilar welds. PY - 2012 SN - 978-3-87155-608-1 SN - 1618-4513 VL - 4 SP - 153 EP - 161 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-26829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Regulating the Use of New Materials in Containment Systems for Dangerous Goods T2 - MRS Fall Meeting CY - Boston, MA, USA DA - 2008-12-01 PY - 2008 AN - OPUS4-19637 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Goedecke, Thomas A1 - Menrad, Andreas A1 - Bethke, John T1 - Application of nondestructive testing - Methods for packaging examination N2 - Nondestructive testing (NDT) methods are applicable in many ways for defect detection as well as optimization of packaging production processes. The visual inspection method is the technique which is mostly used, although neither the customer nor a skilled inspector may be aware of this. Techniques like ultrasound for wall thickness measurement, the application of x-ray techniques or the use of dye penetrant techniques for crack detection are rather well known to the NDT family. However, acoustic emission techniques can also be helpful for the characterization of packaging materials. In this paper the employment of x-ray computer tomography (CT) for measurement of wall thickness in plastic jerrycans, especially on the edges, and its possible optimization of production processes will be discussed. A comparison of the CT and ultrasonic examinations of wall thickness and the reliability of this measured data are also important points for the discussion, especially if some safety factors can be derived from the results. The leakage test is also good for jerrycans, IBCs or other kinds of drums for the transportation and storage of dangerous goods. The disadvantage of this kind of test is that a lack of quality, e.g. wall thickness deterioration, cannot be detected if the wall thickness withstands the internal pressure. Therefore, especially for Quality assurance, the other, previously mentioned techniques are better for a statistical assessment of a batch. This paper is focused on the comparison of different NDT results with special emphasis on the large range of material mechanical properties. T2 - 25th IAPRI Symposium on Packaging CY - Berlin, Germany DA - 16.05.2011 KW - Materialeigenschaft KW - Zerstörungsfreie Prüfung KW - Computertomographie KW - Kunststoffbehälter PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-239191 SN - 978-3-940283-31-3 VL - 126 SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-23919 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -