TY - JOUR A1 - Kapa, Thomas A1 - Schreier, Andy A1 - Krebber, Katerina T1 - 63 km BOFDA for temperature and strain monitoring N2 - We demonstrate (and are the first to do so) 63 km Brillouin Optical Frequency-Domain Analysis (BOFDA) for temperature and strain monitoring using a 100 km fiber loop. The use of BOFDA for long-range applications can be considered a novel approach, as previous investigations focused on the utilization of Brillouin Optical Time-Domain Reflectometry and Analysis (BOTDR and BOTDA, respectively). At 51.7 km, a 100 m hotspot (37 °C) was detected without using distributed Raman amplification or image processing. KW - Distributed sensing KW - Stimulated Brillouin scattering KW - Fiber optics sensors PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-449679 DO - https://doi.org/10.3390/s18051600 SN - 1424-8220 VL - 18 IS - 5 SP - 1600, 1 EP - 9 PB - MDPI CY - Basel, Switzerland AN - OPUS4-44967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schreier, Andy A1 - Liehr, Sascha A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Investigation on the influence of humidity on stimulated Brillouin backscattering in perfluorinated polymer optical fibers N2 - In this paper perfluorinated graded-index polymer optical fibers are characterized with respect to the influence of relative humidity changes on spectral transmission absorption and Rayleigh backscattering. The hygroscopic and thermal expansion coefficient of the fiber are determined to be CHE = (7.4 +/- 0.1) 10^-6 %r.h.^-1 and CTE = (22.7 +/- 0.3) 10^-6 K^-1, respectively. The influence of humidity on the Brillouin backscattering power and linewidth are presented for the first time to our knowledge. The Brillouin backscattering power at a pump wavelength of 1319 nm is affected by temperature and humidity. The Brillouin linewidth is observed to be a function of temperature but not of humidity. The strain coefficient of the BFS is determined to be CS = (146.5 +/- 0.9) MHz/% for a wavelength of 1319 nm within a strain range from 0.1 % to 1.5 %. The obtained results demonstrate that the humidity-induced Brillouin frequency shift is predominantly caused by the swelling of the fiber over-cladding that leads to fiber straining. KW - Brillouin KW - Polymer optical fibre KW - Humidity PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-465932 DO - https://doi.org/10.3390/s18113952 SN - 1424-8220 VL - 18 IS - 11 SP - 3952, 1 EP - 12 PB - MDPI CY - Basel, Switzerland AN - OPUS4-46593 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Distributed Brillouin sensors based on POF - a brief overview N2 - Easy to handle and stretchable polymer optical fibres for sensor applications Basic idea of stimulated Brillouin scattering Brillouin threshold for PMMA-POF and PFGI-POF in comparison Sensorial behavior of Brillouin scattering in PFGI-POF and silica SMF Basics and classification of distributed Brillouin sensing methods Basic idea of dynamic Brillouin sensing T2 - Institutsseminar Hochfrequenztechnik CY - Technische Universität Braunschweig, Germany DA - 24.01.2017 KW - Distributed sensing KW - Brillouin KW - Polymer optical fibre PY - 2017 AN - OPUS4-39030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aleksander, Wosniok A1 - Schreier, Andy T1 - Toward investigation of Brillouin scattering in multimode polymer and silica optical fibers N2 - In this paper, we present a study aimed at characterizing the optimal fiber optic components for Brillouin sensing in multimode fibers. For this purpose the use of single-mode and multimode circulators as well as couplers typically used in the Brillouin measurement setups was investigated. On the one hand the undesired coupling losses between conventional fiber optic measurement system components and a multimode sensor fiber can be overcome by replacing the singlemode components with their own multimode equivalents. On the other hand the use of multimode fiber optic circulators and multimode couplers affects the mode distribution of laser light which can impair the measurement signal backscattered in the multimode sensor fibers. In view of an increasing interest in high strain measurements using polymer optical fibers (POFs) as Brillouin-distributed sensors the investigation on Brillouin scattering effects in multimode fibers (MMFs) was performed on a low-loss perfluorinated graded-index polymer optical fiber (PFGI-POF). The obtained results were compared with those of a standard graded-index multimode (GI-MMF) silica glass optical fiber (GOF). This study confirms the relevance of the adaptation of the measurement system components to the use of the multimode sensor fibers. In addition, due to mode coupling effects occurring in the tested POF itself, the results show differences in the yield of the components adaptation in the sensory implementation of the two kinds of the tested optical fibers. T2 - SPIE’s 2017 International Symposium on Optics & Optoelectronics: Micro-structured and Specialty Optical Fibres CY - Prag, CZ DA - 26.04.2017 KW - Brillouin KW - Distributed sensing KW - Polymer optical fibre PY - 2017 SN - 978-1-5106-0965-5 SN - 978-1-5106-0966-2 DO - https://doi.org/10.1117/12.2267823 SN - 0277-786X VL - 10232 SP - 102320M-1 EP - 102320M-6 PB - SPIE AN - OPUS4-40471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - POF-based distributed Brillouin sensing N2 - In this presentation the need of distributed Brillouin sensors in POF is underlined. In-situ structual health monitoring applications were shown and a possible experimental setup was presented. T2 - The Fiber Society’s Spring 2017 Conference CY - Aachen, Germany DA - 17.05.2017 KW - Brillouin KW - Distributed sensing KW - Polymer optical fibre PY - 2017 AN - OPUS4-40315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Toward investigation of Brillouin scattering in multimode polymer and silica optical fibers N2 - In this paper, we present a study aimed at characterizing the optimal fiber optic components for Brillouin sensing in multimode fibers. For this purpose the use of single-mode and multimode circulators as well as couplers typically used in the Brillouin measurement setups was investigated. On the one hand the undesired coupling losses between conventional fiber optic measurement system components and a multimode sensor fiber can be overcome by replacing the single-mode components with their own multimode equivalents. On the other hand the use of multimode fiber optic circulators and multimode couplers affects the mode distribution of laser light which can impair the measurement signal backscattered in the multimode sensor fibers. In view of an increasing interest in high strain measurements using polymer optical fibers (POFs) as Brillouin-distributed sensors the investigation on Brillouin scattering effects in multimode fibers (MMFs) was performed on a low-loss perfluorinated graded-index polymer optical fiber (PFGI-POF). The obtained results were compared with those of a standard graded-index multimode (GI-MMF) silica glass optical fiber (GOF). This study confirms the relevance of the adaptation of the measurement system components to the use of the multimode sensor fibers. In addition, due to mode coupling effects occurring in the tested POF itself, the results show differences in the yield of the components adaptation in the sensory implementation of the two kinds of the tested optical fibers. T2 - SPIE’s 2017 International Symposium on Optics & Optoelectronics: Micro-structured and Specialty Optical Fibres CY - Prag, Czech Republic DA - 26.04.2017 KW - Brillouin KW - Distributed sensing KW - Polymer optical fibre PY - 2017 AN - OPUS4-40318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - POF-based Distributed Brillouin Sensing N2 - In this presentation the need of distributed Brillouin sensors in POF is underlined. The usage of FBGs for measurment improvements was presented. In-situ structual health monitoring applications were shown and a possible experimental setup was presented. T2 - Presentation at Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute CY - Goslar, Germany DA - 15.08.2017 KW - Brillouin KW - Distributed sensing KW - Polymer optical fibre PY - 2017 AN - OPUS4-41386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy A1 - Jeschke, T. A1 - Petermann, K. A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Analytical model for mode-based insertion loss in ball-lensed coupling of graded-index silica and polymer fibres N2 - Analytical model for ball-lensed couplers to calculate the insertion loss for each optical mode. The basis for the calculation are commercial perfluorinated polymer optical (PFGI-POFs) and silica based fibres (SOFs). The modal power distribution for given misalignments are presented as well as the reflection-based losses at all optical interfaces. Additionally, the ball-lensed interconnection between PFGI-POF and SOF was theoretically demonstrated. T2 - POF 2017: 26th International Conference on Plastic Optical Fibres CY - Aveiro, Portugal DA - 13.09.2017 KW - Polymer optical fibre KW - Optical connector PY - 2017 VL - 2017 SP - 1 EP - 4 AN - OPUS4-41979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Analytical model for mode-based insertion loss in ball-lensed coupling of graded-index silica and polymer fibres N2 - Analytical model for ball-lensed couplers to calculate the insertion loss for each optical mode. The basis for the calculation are commercial perfluorinated polymer optical (PFGI-POFs) and silica based fibres (SOFs). The modal power distribution for given misalignments are presented as well as the reflection-based losses at all optical interfaces. Additionally, the ball-lensed interconnection between PFGI-POF and SOF was theoretically demonstrated. T2 - POF 2017: 26th International Conference on Plastic Optical Fibres CY - Aveiro, Portugal DA - 13.09.2017 KW - Polymer optical fibre KW - Optical connector PY - 2017 AN - OPUS4-41974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kapa, Thomas A1 - Schreier, Andy A1 - Krebber, Katerina T1 - A 100-km BOFDA Assisted by First-Order Bi-Directional Raman Amplification N2 - We present, to our knowledge for the first time, a 100-km Brillouin Optical Frequency-Domain Analysis (BOFDA) employing a 200-km fiber loop. Compared to our previous publication, enhanced sensor length, sensor accuracy and spatial resolution are presented. The performance improvements are achieved by applying distributed Raman amplification (DRA) and a digital high-pass filter. We report on temperature measurements over sensing distances of 75 km and 100 km both with a 12.5-m spatial resolution. Temperature changes of 5 °C have been measured along 75 km sensing fiber. A temperature change of 30 °C has been detected at 99.5 km. KW - Distributed sensing KW - Fiber optics sensors KW - Stimulated Brillouin scattering PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-476577 DO - https://doi.org/10.3390/s19071527 SN - 1424-8220 VL - 19 IS - 7 SP - 1527, 1 EP - 9 PB - MDPI CY - Basel, Switzerland AN - OPUS4-47657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy A1 - Liehr, Sascha A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Comparison of solution approaches for distributed humidity sensing in perfuorinated graded-index polymer optical fibers N2 - We compare four different sensing solutions suitable for distributed fiber optic humidity sensing in per uorinated graded-index polymer optical fibers (PFGI-POFs). Compared to silica fbers, polymer optical fibers over advantageous beneffits including signifficantly higher break down strain, fracture toughness and humidity sensitivity. Various humidity-related effects in PFGI-POFs have been reported in the last years including measured attenuation and length changes as well as Brillouin frequency and Bragg wavelength shifts. The four aforementioned methods could serve as a basis for distributed and quasi-distributed humidity sensing and are described here closely with an emphasis on plausible cross effects to temperature and strain. The main focus of this paper lies on the comparison of four approaches with regard to method complexity, sensitivity to humidity, spatial resolution, real-time capability and effort to compensate for cross effects. T2 - SPIE Optics + Optoelectronics CY - Prague, Czech Republic DA - 01.04.2019 KW - Distributed sensing KW - Humidity KW - Polymer optical fibre PY - 2019 SN - 978-1-5106-2723-9 DO - https://doi.org/10.1117/12.2522307 SN - 0277-786X SN - 1996-756X SP - 1102808-1 EP - 1102808-9 PB - SPIE AN - OPUS4-47844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Distributed Brillouin sensing in polymer optical fibers N2 - A brief overview about the results obtained within the BAM PhD framwork. T2 - Meeting of the Terahertz-Photonics-Group at IHF, Technische Universität Braunschweig CY - Braunschweig, Germany DA - 17.07.2019 KW - Brillouin KW - Distributed sensing KW - Polymer optical fibre PY - 2019 AN - OPUS4-48501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Schreier, Andy A1 - Krebber, Katerina T1 - Distributed BOFDA measurement on an 86 m long perfluorinated polymer optical fiber N2 - We present our research on the development of a Brillouin optical frequency-domain analysis (BOFDA) using a perfluorinated graded-index polymer optical fiber (PFGI-POF) as a sensing fiber. The described works include investigations both on the selection of the setup components with respect to mode coupling effects and on the impact of the humidity cross-sensitivity. The suitability of the developed POF-based BOFDA is proved by a distributed measurement on an 86 m long PFGI-POF recorded with the spatial resolution of 6 m. T2 - 28th International Conference on Plastic Optical Fibers CY - Yokohama, Japan DA - 20.11.2019 KW - Brillouin sensing KW - BOFDA KW - Perfluorinated graded-index polymer optical fiber KW - PFGI-POF PY - 2019 SP - 27 EP - 28 AN - OPUS4-49865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Comparision of solution approaches for distributed humidity sensing in PFGI-POF N2 - We compare four different sensing solutions suitable for distributed fiber optic humidity sensing in per uorinated graded-index polymer optical fibers (PFGI-POFs). Compared to silica fbers, polymer optical fibers over advantageous beneffits including signifficantly higher break down strain, fracture toughness and humidity sensitivity. Various humidity-related effects in PFGI-POFs have been reported in the last years including measured attenuation and length changes as well as Brillouin frequency and Bragg wavelength shifts. The four aforementioned methods could serve as a basis for distributed and quasi-distributed humidity sensing and are described here closely with an emphasis on plausible cross effects to temperature and strain. The main focus of this paper lies on the comparison of four approaches with regard to method complexity, sensitivity to humidity, spatial resolution, real-time capability and effort to compensate for cross effects. T2 - SPIE 2019 International Symposium on Optics + Optoelectronics: Optical Sensors CY - Prague, Czech Republic DA - 01.04.2019 KW - Polymer optical fibre KW - Distributed sensing KW - Humidity PY - 2019 AN - OPUS4-47741 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -