TY - JOUR A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Kormunda, M. A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Nooke, Alida A1 - Pavlik, J. A1 - Steinbach, J. T1 - SPR enhanced ellipsometric gas monitoring on thin iron doped tin oxide layers N2 - In this work, thin iron doped tin oxide layers (3–6 nm) were investigated with regard to gas sensitivity by means of surface plasmon resonance (SPR) effect with ellipsometric readout. The experimental set-up was a Kretschmann configuration with gold as metal layer. The sensor system was exposed to different concentrations of methane in the low ppm range and the sensor response of an uncoated gold layer compared to a gold layer coated with iron doped tin oxide. The additional layer effects stability with regard to drift behavior of the sensor and an increase in sensitivity. Furthermore, the sensor is able to detect the toxic gas carbon monoxide in low concentration range (down to 0.5 ppm). The thin layers were investigated by X-ray photoelectron spectroscopy, secondary electron microscopy and spectroscopic ellipsometry. The possible mechanisms taking place on the surface are discussed. KW - Gas sensing KW - SPR effect KW - Iron doped tin oxide KW - Ellipsometry PY - 2011 DO - https://doi.org/10.1016/j.snb.2011.08.036 SN - 0925-4005 SN - 1873-3077 VL - 160 IS - 1 SP - 609 EP - 615 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-24826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nooke, Alida A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Negendank, Detlef A1 - Steinbach, J. T1 - On the application of gold based SPR sensors for the detection of hazardous gases N2 - A gas sensor system based on the surface plasmon resonance (SPR) effect in a 44 nm Au layer was studied. The usability of this sensor system was investigated for several analyte gases and gas mixtures which are interesting due to their flammability, toxicity or greenhouse effect. The SPR effect of gold was measured in nitrogen and compared with the gaseous alkane series which caused a shift of the position of the SPR effect. For in situ measurements, the phase shift Δ at the SPR angle (ψ minimum) in the analyte gas mixtures was measured for investigated gases in comparison with nitrogen. With this method, detection limits of different gases could be determined, which lie in a range interesting for safety engineering. Furthermore the aging effect of the gold layers which leads to loss in sensitivity of the sensor was investigated. KW - Ellipsometry KW - SPR effect KW - Gas sensing KW - Gold layer PY - 2010 DO - https://doi.org/10.1016/j.snb.2010.05.061 SN - 0925-4005 SN - 1873-3077 VL - 149 IS - 1 SP - 194 EP - 198 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-21673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, Christina A1 - Yin, Huajie A1 - Cerclier, C. A1 - Morineau, D. A1 - Wurm, Andreas A1 - Schick, C. A1 - Emmerling, Franziska A1 - Schönhals, Andreas T1 - Molecular dynamics of a discotic liquid crystal investigated by a combination of dielectric relaxation and specific heat spectroscopy N2 - The molecular dynamics of the discotic liquid crystal pyrene-1,3,6,8-tetracarboxylic tetra(2-ethylhexyl)ester is studied by dielectric relaxation and specific heat spectroscopy. Dielectric spectroscopy shows 3 processes: a β-relaxation at low temperatures and an α-relaxation in the temperature range of the mesophases followed by conductivity. The dielectric α-relaxation is assigned to a restricted glassy dynamics in the plastic crystal as well as in the liquid crystalline phase. The obtained different Vogel–Fulcher–Tammann laws (different Vogel temperatures and fragility) are related to the different restrictions of the dipolar fluctuations in the corresponding phases. By means of specific heat spectroscopy glassy dynamics is also detected in the plastic crystalline phase but with quite a different temperature dependence of the relaxation times. This is discussed considering the different probes involved and how they are influenced by the structure. In the frame of the fluctuation approach a correlation length of glassy dynamics is calculated to 0.78 nm which corresponds to the core–core distance estimated by X-ray scattering. PY - 2012 DO - https://doi.org/10.1039/c2sm25610j SN - 1744-683X VL - 8 IS - 43 SP - 11115 EP - 11122 PB - RSC Publ. CY - Cambridge AN - OPUS4-26826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nooke, Alida A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Negendank, Detlef A1 - Steinbach, J. T1 - Ellipsometric detection of gases with the surface plasmon resonance effect on gold top-coated with sensitive layers N2 - An ellipsometric gas sensor based on the surface Plasmon resonance (SPR) effect of ~ 43 nm thick gold layers was investigated. To protect the gold layer from contamination and to improve the detection limits, the gold layers were top-coated with 5–6 nm thick layers of organic a-C:H or with inorganic metal oxides TiO2 or ZrO2. The additional layers increased the long-term stability, whereas the metal oxide layers protect better than a-C:H. Furthermore, the additional layers decreased the detection limits by one order of magnitude in case of a-C:H and two orders of magnitude in case of the oxides. It could be shown that the detection limits also depend on the kind of preparation (sol–gel process or physical vapour deposition) of the additional layers. KW - Gas sensor KW - SPR KW - Ellipsometry KW - Sensitive layer KW - TiO2 KW - ZrO2 KW - a-C:H PY - 2011 DO - https://doi.org/10.1016/j.tsf.2010.11.091 SN - 0040-6090 VL - 519 IS - 9 SP - 2659 EP - 2663 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Rieck, C. A1 - Hillemeier, B. T1 - Use of Low Frequency Ultrasound Echo Technique to Determine Cavities in Wooden Construction Composites T2 - 6th International Symposium Non-Destructive Testing in Civil Engineering (NDT-CE) CY - Berlin, Germany DA - 2003-09-16 PY - 2003 UR - http://www.ndt.net/article/ndtce03/papers/p051/p051.htm SN - 3-931381-49-8 SP - 1(?) EP - 9(?) PB - DGZfP CY - Berlin AN - OPUS4-3230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin ED - Cziesielski, E. T1 - Ultraschallechoverfahren an Holz PY - 2004 SN - 3-433-01705-0 SP - 52 EP - 58 PB - Ernst CY - Berlin AN - OPUS4-3145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Rieck, C. A1 - Hillemeier, B. A1 - Krause, Martin T1 - Hohlstellenortung in Holzbalken mit dem Ultraschallverfahren N2 - Zusammenfassung Die Anwendung des Ultraschallecho-Verfahrens zur Hohlstellenortung in Holzbalken wird beschrieben. An Hand der Versuchsergebnisse wird der Einfluss der Anisotropie des Holzes auf die Messkopfanordnung und Schallgeschwindigkeit dargestellt. Mit der optimierten Messanordnung ist die erfolgreiche Detektierung von Nachbildungen von Minderdicken und Kernfäule möglich. Besonders klar sind Schäden in Faserrichtung (Kernfäulenachbildung) nachzuweisen. Die sehr guten Ergebnisse zeigen die Anwendbarkeit des Ultraschallecho-Verfahrens an Holz. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - ZfP an Holzbauteilen KW - Fehlstellen KW - Minderdicken KW - Ultraschallecho-Experimente an Probekörpern PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/p32/p32.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc A1 - Geißler, Andreas A1 - Krause, Ulrich T1 - Zum Einfluss der Turbulenz auf die Druckentlastung von Gas- und Staubexplosionen N2 - Der maßgebliche Einfluss turbulenter Strömungsbewegungen auf den Ablauf von Explosionen ist bereits seit längerem bekannt. Wegen der Schwierigkeit, Betrag und Richtung der turbulenten Schwankungsgeschwindigkeit in-situ zu messen, existieren jedoch nur wenige diesbezügliche experimentelle Daten. Es wurde deshalb eine aus drei Glassegmenten bestehende Versuchsapparatur mit etwa 100 l Volumen und einem Länge/Durchmesser-Verhältnis von 4,7 errichtet, die die gleichzeitige Messung der Strömungsgeschwindigkeit und deren turbulenter Fluktuation, der Ausbreitungsgeschwindigkeit der Flamme, der zeitlichen Entwicklung des Explosionsdruckes sowie im Falle von Staubexplosionen der Staubkonzentration erlaubte. Die Glassegmente wurden durch Metallflansche verbunden, an welche insgesamt sechzehn gleichmäßig über Umfang und Höhe verteilte Ventilatoren zur kontrollierten Erzeugung eines Turbulenzfeldes montiert waren. Die Explosionsversuche wurden mit einem Propan-Stickstoff-Sauerstoff-Gemisch sowie mit einem Maisstärke-Luft-Gemisch durchgeführt. Die Zündung der explosionsfähigen Gemische erfolgte durch einen Hochspannungsfunken. Als Berstfolien wurden zwei Polyethylenfolien (Dicke 10 und 15 µm) und drei Aluminiumfolien (Dicke 15, 20 und 22 µm) verwendet. Die Versuche zeigten sowohl bei Gas- als auch bei Staubexplosionen eine Zunahme des reduzierten Explosionsdruckes für wachsende turbulente Schwankungs-geschwindigkeiten im Bereich von 0 m/s bis 0,45 m/s. Diese Zunahme war besonders ausgeprägt für verhältnismäßig kleine Entlastungsflächen (Durchmesser < 70 mm) bei geringen Ansprechdrücken (Polyethylenfolie), während für höhere Ansprechdrücke (Aluminiumfolie) der Einfluss der Turbulenz zurückging. Zur Ergänzung der Experimente wurden Simulationsrechnungen mit dem Computational Fluid Dynamics-Programm Fluent6 unternommen. Diese Rechnungen dienten der Validierung der den Programmen zugrunde liegenden Modelle im Hinblick auf ihre Anwendbarkeit zur Berechnung von Explosionsabläufen in technischen Anlagen. Es konnte eine realistische Wiedergabe der Druck-Zeit-Verläufe durch die Rechnungen erreicht werden. T2 - 7. Fachtagung Arbeits-, Anlagen- und Umweltsicherheit CY - Köthen, Deutschland DA - 2004-11-04 PY - 2004 SP - 15 Seiten (A 04) PB - VDI-Verl. CY - Halle AN - OPUS4-5069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc A1 - Geißler, Andreas A1 - Krause, Ulrich T1 - Experiments on the Influence of Turbulence on Vented Gas and Dust Explosions T2 - 5th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Cracow, Poland DA - 2004-10-10 KW - Gas explosion KW - Dust explosion KW - Turbulence KW - Venting PY - 2004 SP - 176 EP - 187 PB - Central Mining Institute CY - Kattowitz AN - OPUS4-5074 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Hillemeier, B. A1 - Krause, Martin ED - Bröker, F. T1 - Defect localisation in wood with low frequency ultrasonic echo technique T2 - 14th International Symposium on Nondestructive Testing of Wood CY - Eberswalde, Germany DA - 2005-05-02 PY - 2005 SN - 3-8322-3949-9 SP - 331 EP - 336 PB - Shaker CY - Aachen AN - OPUS4-11307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Lutz, J. A1 - Hillemeier, B. A1 - Rieck, C. T1 - Niederfrequente Ultraschall-Echo-Verfahren und Bohrwiderstandsmessung zur Untersuchung von Holzbauteilen T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - ZfP an Holzbauteilen KW - Fehlstellen KW - Minderdicken KW - Ultraschallecho-Experimente an Probekörpern KW - Ultraschall-Echo KW - Fäulnis KW - Bauwesen PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 11(?) PB - DGZfP CY - Berlin AN - OPUS4-11960 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Hillger, w. A1 - Bühling, L. A1 - Ilse, D. A1 - Hillemeier, B. A1 - Rieck, C. T1 - Luftultraschall und Ultraschall-Echo-Technik an Holz T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - ZfP an Holzbauteilen KW - Fehlstellen KW - Minderdicken KW - Ultraschallecho-Experimente an Probekörpern KW - Ultraschall-Echo KW - Fäulnis KW - Bauwesen KW - Luftultraschall PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 15(?) PB - DGZfP CY - Berlin AN - OPUS4-11961 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moritz, W. A1 - Krause, S. A1 - Roth, U. A1 - Klimm, D. A1 - Lippitz, Andreas T1 - Re-activation of an all solid state oxygen sensor N2 - The silicon based semiconductor structure Si/SiO2/Si3N4/LaF3/Pt can be used as a potentiometric oxygen sensor working at room temperature. A thermal re-activation can be applied to overcome the earlier disadvantage of an increase in response time with continuous use. Using the Pt gate electrode as a resistive heater, very short electrical high-power pulses can be applied. A heating time as short as 300 ns was sufficient for the re-activation of the sensor. This way, only the sensitive thin layer system LaF3/Pt was heated, and the whole sensor was at room temperature immediately after heating. Impedance spectroscopy, X-ray photoelectron spectroscopy (XPS) and quadruple mass spectrometric (QMS)–thermogravimetry (TG) were used to investigate the mechanism of deterioration in dynamic sensor behaviour and re-activation. The formation of hydrated carbonate and the desorption of CO2 and H2O have been shown to be the causes. KW - Chemical sensor KW - Thermal treatment KW - Activation KW - LaF3 KW - Pt PY - 2001 DO - https://doi.org/10.1016/S0003-2670(01)00993-X SN - 0003-2670 SN - 1873-4324 SN - 0378-4304 VL - 437 SP - 183 EP - 190 PB - Elsevier CY - Amsterdam AN - OPUS4-6836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Scheer, C. T1 - Zerstörungsfreie Integritätsprüfung von Holz mit dem Ultraschallecho-Verfahren T2 - Forschungskolloquium "Holzbau Forschung + Praxis" CY - Stuttgart, Deutschland DA - 2006-02-23 PY - 2006 SP - 33 EP - 40 PB - Technische Universität Stuttgart CY - Stuttgart AN - OPUS4-12242 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheid, Marc A1 - Geißler, Andreas A1 - Krause, Ulrich T1 - Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions N2 - Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture. It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence. KW - Gas explosions KW - Dust explosions KW - Turbulence KW - Venting PY - 2006 DO - https://doi.org/10.1016/j.jlp.2007.03.001 SN - 0950-4230 SN - 1873-3352 VL - 19 IS - 2-3 SP - 194 EP - 199 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-11833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Osterloh, Kurt A1 - Hasenstab, Andreas A1 - Ewert, Uwe A1 - Krause, Martin A1 - Goebbels, Jürgen T1 - Mobile radiographische Untersuchung von Holz und Bäumen T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - Digitale Radiographie KW - Mobiles Röntgen PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 8(?) PB - DGZfP CY - Berlin AN - OPUS4-11866 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Rieck, C. A1 - Hillemeier, B. T1 - Materialuntersuchung an Holz mit niederfrequenter Ultraschall-Echotechnik N2 - Kurzfassung Die Anwendung niederfrequenter Ultraschall-Echotechnik mit Longitudinal- und Transversalwellen für die Materialuntersuchung von Holzbauteilen wird beschrieben. Weiterhin wird der Einfluss der Holzfasern auf die Schallgeschwindigkeiten und Oberflächenwellen an Hand von Messergebnissen aufgezeigt. Die Leistungsfähigkeit des Ultraschall-Echoverfahrens an ungeschädigten Holzkörpern und Körpern mit eingebrachten Bohrungen in Faserrichtung (Kernfäulnissimulation) wird dargestellt. Es ist zudem möglich, bei koppelmittelfreier Ankopplung mit Transversalwellen indirekt Fäulnis von der ungeschädigten Bauteilseite aus zu orten. Als Referenzverfahren werden die Bohrwiderstandsmethode oder die Röntgendurchstrahlung eingesetzt. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2004 CY - Salzburg, Österreich DA - 2004-05-17 PY - 2004 UR - http://www.ndt.net/article/dgzfp04/papers/v87/v87.htm SN - 3-931381-55-2 SP - 1(?) EP - 9(?) PB - DGZfP CY - Berlin AN - OPUS4-5216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Osterloh, Kurt A1 - Robbel, Joachim A1 - Krause, Martin A1 - Ewert, Uwe A1 - Hillemeier, B. T1 - Mobile Röntgenblitzröhren zum Auffinden von Holzschäden N2 - In diesem Beitrag wird die Anwendung von Radiographiesystemen zum Auffinden von Holzschäden beschrieben. Die Anlage besteht aus einer mobilen Röntgenblitzröhre und einem digitalen Radiographiesystem mit Speicherfolie oder einem Flachdetektor. An Hand der durchgeführten Versuche an Laub- und Nadelbäumen sowie an Eichenbalken der Marienkirche der Lutherstadt- Wittenberg wird die Detektion innerer Schäden gezeigt. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2004 CY - Salzburg, Österreich DA - 2004-05-17 PY - 2004 UR - http://www.ndt.net/article/dgzfp04/papers/p15/p15.htm SN - 3-931381-55-2 SP - 1(?) EP - 8(?) PB - DGZfP CY - Berlin AN - OPUS4-5217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin T1 - Ultraschall-Echo-Technik zur Ortung von Minderdicken und Schäden in Holzbauteilen T2 - DGZfP-Fachtagung Bauwerksdiagnose "Praktische Anwendungen Zerstörungsfreier Prüfungen" CY - Berlin, Deutschland DA - 2006-02-22 KW - Zerstörungsfreie Prüfung KW - Holz KW - Ultraschallecho KW - ZfP an Holzbauteilen KW - Fehlstellen KW - Minderdicken KW - Ultraschall-Echo KW - Fäulnis KW - Bauwesen PY - 2006 SN - 3-931381-71-4 SP - 1(?) EP - 11(?) PB - DGZfP CY - Berlin AN - OPUS4-14233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Osterloh, Kurt T1 - Testing Of Wooden Construction Elements with Ultrasonic Echo Technique and X-Ray T2 - 9th European Conference on NDT CY - Berlin, Germany DA - 2006-09-25 KW - NDT of Wood PY - 2006 SN - 3-931381-86-2 SP - 1(?) EP - 8(?) PB - European Federation for Non-Destructive Testing CY - Berlin AN - OPUS4-14422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -