TY - JOUR A1 - Sichler, Theresa Constanze A1 - Adam, Christian A1 - Montag, D. A1 - Barjenbruch, M. T1 - Future nutrient recovery from sewage sludge regarding three different scenarios - German case study N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, German wastewater treatment plants (WWTPs) must recover phosphorus (P) from sewage sludge if it contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs >100,000 population equivalents (pe) from 2029 and >50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 16% of the total disposal in 2019. The reports of 10 states were evaluated for 2016 and 2017 representing approx. 60% of the total agriculturally used sludge volume. In 2016, 60% of the WWTPs’ sludges exceeded the recovery limit of 2 wt % P which is 70% of the amount of sludge and 85% of the phosphorus load. Other nutrients are not affected by the recovery obligation. However, many P recovery processes recover other nutrients, too. Considering three different scenarios for future German sewage sludge disposal shows that 70–77% of the P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0–16% nitrogen, 36–52% of calcium, 31–53% of potassium, and 40–52% of magnesium. However, these recovered nutrients loads can substitute only 1% or less of the commercial fertilizer demand except from phosphorus which is up to 43% of the demand. KW - Sewage sludge KW - Phosphorus recovery KW - Wastewater KW - Sewage sludge disposal PY - 2022 DO - https://doi.org/10.1016/j.jclepro.2021.130130 VL - 333 SP - 1 EP - 10 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-54186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - R-Rhenania - Modifiziertes Rhenaniaphosphat aus Klärschlammasche für Bayern N2 - Vorstellung des Projektstands R-Rhenania aus der Förderinitiative RePhoR des BMBF. T2 - DPP FORUM 2022: Phosphor Recycling 2029 Etappenziel erreicht? CY - Frankfurt a.M., Germany DA - 13.10.2022 KW - Phosphorrückgewinnung KW - Klärschlammasche KW - thermochemische Behandlung PY - 2022 AN - OPUS4-55980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Souza Filho, I. A1 - Adam, Christian T1 - Fundamentals of the hydrogen plasma reduction of iron ores N2 - Hydrogen plasma treatment of iron ores or iron oxide containing wastes can be an efficient option to produce green iron e.g. for steel production. This way iron oxide is reduced to metallic iron in the liquid form by the highly reactive species that are formed in a hydrogen plasma. Hydrogen plasma can be used at the same time to remove undesired gangue elements. The presentation shows the experimental setup, shows first results of iron ore reduction by hydrogen plasma and gives an outlook for industrial application of the technology. T2 - European Academic Symposium on EAF steelmaking (EASES 2023) CY - Oulu, Finland DA - 05.06.2023 KW - Hydrogen KW - Plasma KW - Reduction PY - 2023 AN - OPUS4-57626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 AN - OPUS4-57683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J.H. T1 - Schwankungen der P-Gehalte in Klärschlämmen im Kontext der Klärschlammverordnung N2 - Ab 2029 gilt für alle Kläranlagen in Deutschland eine Pflicht zur Rückgewinnung von Phosphor (P) aus Klärschlamm. Ausgenommen sind nur Anlagen mit Schlämmen mit weniger als 20 g P/kg bezogen auf die Trockenmasse (TM). Für eine Überprüfung der Phosphorschwankungen im Klärschlamm wurden neun verschiedene Kläranlagen ausgewählt mit Phosphorgehalten nahe der "Rückgewinnungsgrenze" von 20 g/kg TM. Der entwässerte Klärschlamm dieser Anlagen wurde monatlich beprobt und auf seinen Phosphorgehalt geprüft. Die Phosphorschwankungen betrugen je nach Anlage zwischen 4 % und 13 % (relative Standardabweichung), im Mittel rund 7 %. T2 - KlärschlammTage CY - Online Meeting DA - 09.06.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Abwasserbehandlung KW - Klärschlammverordnung PY - 2021 SP - 102 EP - 108 PB - Deutsche Vereinigung für Wasserwirtschaft, Abwasser und Abfall e. V. (DWA) CY - Hennef AN - OPUS4-52839 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - P-Rückgewinnungspflicht nach AbfKlärV - Betrachtungen zu Konzentrationen und Frachten N2 - Vortrag über die Regelungen der AbfKlärV bezüglich P-Rückgewinnung. Diskussion der Auswirkung einer konzentrationsbezogenen Grenze auf die Pflicht zur P-Rückgewinnung. Diskussion der nach AbfKlärV zulässigen analytischen Verfahren zur Bestimmung von P in Klärschlamm und Ableitung von Empfehlungen. Vorstellung der Ergebnisse eines Ringversuchs mit 28 Laboren. T2 - KlärschlammTage Würzburg CY - Würzburg, Germany DA - 23.05.2023 KW - Klärschlamm KW - P-Rückgewinnung KW - Ringversuch P-Gehalt in Klärschlamm PY - 2023 AN - OPUS4-57541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Barjenbruch, M. ED - Holm, O. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Nährstoffrückgewinnung aus Klärschlamm: Eine Betrachtung zukünftiger Verwertungsszenarien für Deutschland N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturally used sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too. Considering three differentscenariosfor future German sewage sludge disposal Shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nutrient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 15.11.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Landwirtschaftliche Klärschlammverwertung KW - Klärschlammverordnung PY - 2021 SN - 978-3-944310-56-5 VL - 4 SP - 252 EP - 265 PB - Thomé-Kozmiensky-Verlag GmbH CY - Neuruppin AN - OPUS4-54117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Cloop - Closing the global nutrient loop N2 - Recycled fertilizers produced using processes for the recovery of phosphate from residual materials such as wastewater, sewage sludge and sewage sludge ashes show very good bioavailability, but it is still a product largely unknown to the market. The aim of CLOOP is therefore to document the properties and effects of such fertilizers through chemical, mineralogical and ecological analyses as well as analytical method development and pot and field plant growth trials. Outotec focused on 3 points in CLOOP: Experimental campaigns, process simulations as well as economic analyses with focus on the AshDec process, respectively the design of a large-scale AshDec plant for phosphorus recovery. The laboratory scale trials as well as the semi-industrial scale campaign provided valuable insights into the operating parameters of the process and the plant. As a result, for example, the temperature range could be significantly lowered, and the additive addition reduced by approx. 20 %. They have further shown that the AshDec process is not susceptible to operating fluctuations and that the product can be consistently produced at high quality. With the selection of suitable operating parameters, heavy metals (As, Pb, Cd, (Zn)) can be removed. Within the campaign, about 1.5 t of fertilizer for the plant trials in CLOOP could be produced. An AshDec plant process was digitally created in simulation software, allowing valuable process parameters to be simulated at various operating parameters. On this basis, a full-scale plant was designed. The data obtained in the project were used for a detailed economic analysis including a sensitivity analysis. It was possible to show under which conditions this plant can be operated economically. At BAM, the AshDec fertilizer was synthesized with different additives and then applied to plant experiments at Uni Bonn. The goal hereby was to check differences in plant uptake. Because of the promising results of AshDec synthesized with sodium-carbonate and because this AshDec version does not require special off gas treatment for sulfur recovery (compared to AshDec synthesized with sodium-sulfate), all project partners agreed on continuing working with this AshDec variation. It was then used as a raw P-source for formulating it into NPK-fertilizers, by granulation with ammonium-sulfate and straw ash as potassium source. These recycling fertilizers were applied to plant- and field experiments by project partners in Brazil (University of Sao Paulo) and Australia (University of Queensland). Furthermore, in leaching experiments, the solubility of phosphorus in AshDec was compared to triple super phosphate. The experiments were carried out on soils with a varying phosphorus buffering index. Results show, that the phosphorus form in AshDec is way less soluble in water. This indicates that AshDec has the potential for a so-called next generation fertilizer – a fertilizer which’s nutrients remain in the soil and supply the plant according to its needs. At the moment, this behavior gets examined more in depth in lysimeter experiments in cooperation with University of Technology Berlin. The focus of KWB is the Life Cycle Assessment (LCA) of different NextGen fertilizers to evaluate the entire process chain from recovery to fertilizer application. The NextGen fertilizer is credited by the amount of plant available nutrients in the product, which replace nutrients from conventional fertilizer. The LCA covers N-struvite precipitation from municipal wastewater, K-struvite precipitation from industrial wastewater and the AshDec-product from sewage sludge. The LCA task is almost complete. It could be shown that struvite precipitation has comprehensive environmental benefits, mainly since positive side effects occur in sewage sludge treatment (e.g. reduced sludge volume). In principle, the energetic and ecological profile of the AshDec process compared to direct use of sewage sludge ash cannot be assessed as being generally beneficial or negative. Regarding the global warming potential, the Ashdec process shows that the expenses (e.g. energy, chemicals) cannot be covered by the P fertilizer credit. In contrast, the impact categories “terrestrial acidification potential”, and “freshwater eutrophication potential” show positive results as the credits for conventional fertilizer are higher than the burdens for the process. At University Bonn, the standardized pot experiments were conducted with several AshDec variations, using ryegrass, soybean, and spinach on a slightly acidic sandy soil and an organic-free standard substrate. P-uptake and biomass production of different AshDec variations were generally like those of triple super phosphate and struvite, and clearly outperformed untreated sewage sludge ash and rock phosphate. Field trials in Australia and Brazil with sugarcane on acidic soils are still ongoing and results are expected by the end of 2021. T2 - PLANT 2030 Status Seminar 2021 (BMBF) CY - Online meeting DA - 10.03.2021 KW - Recycling fertiliser KW - Phosphorus recovery PY - 2021 AN - OPUS4-52251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Krüger, Oliver A1 - Adam, Christian T1 - Phosphorus fertilizer from sewage sludge ashes by thermochemical treatment - Benefits and challenges N2 - Mineral phosphorus (P) fertilizers are solely produced from phosphate rock. Europe completely depends on imports since there are no relevant phosphate rock deposits on the continent. Furthermore, phosphate rock is contaminated with heavy metals such as Cd and U that pollute the farmlands and pose environmental risks. Sewage sludge ash (SSA) might be a promising source for recycling fertilizer since it contains large amounts of P (up to 13 %). However, fertilizer from SSA has to comply with the respective ordinances, particularly the heavy metal limit values stated in the fertilizer ordinance, and requires sufficient P bioavailability. Thus, we conducted a complete survey of SSA from German mono-incineration facilities and developed a thermochemical treatment for SSA to reduce toxic elements and increase P bioavailability. T2 - RAMIRAN 2015 - 16th International conference Rural-Urban Symbiosis CY - Hamburg, Germany DA - 08.09.2015 PY - 2015 SN - 978-3-941492-95-0 SP - TA EP - O_20, 33 AN - OPUS4-34311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Roskosch, A. A1 - Adam, Christian T1 - Monitoring von Klärschlammaschen N2 - Die Aschen aus der separaten Verbrennung von Klärschlamm in Deutschland besitzen ein großes Potential für die Phosphorrückgewinnung KW - Klärschlammasche KW - Monoverbrennung KW - Phosphor KW - Rückgewinnung KW - Kritische Rohstoffe KW - Seltene Erden PY - 2014 SN - 1868-9531 VL - 27 IS - 3 SP - 8 EP - 12 PB - Rhombos-Verl. CY - Berlin AN - OPUS4-31258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Technische Voraussetzungen für "100%/Zero" P-Dünger T2 - Anforderungen und Beitrag der Landwirtschaft zum Phosphorrecycling CY - Braunschweig, Deutschland DA - 2014-11-06 PY - 2014 AN - OPUS4-32104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Wertstoffpotential in deutschen Klärschlammaschen T2 - Berliner Abfallwirtschafts- und Energiekonferenz CY - Berlin, Germany DA - 2013-01-28 PY - 2013 AN - OPUS4-27624 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Adam, Christian A1 - Hobohm, J. A1 - Basu, S. A1 - Kuchta, K. A1 - van Wasen, Sebastian T1 - Recycling oriented comparison of mercury distribution in new and spent fluorescent lamps and their potential risk N2 - This study compares the mercury distribution in the vapor phase, the phosphor powder and the glass matrix of new and spent fluorescent lamps. The spent fluorescent lamps were obtained at the collection yards of a public waste management company in Hamburg, Germany. An innovative systematic sampling method is utilized to collect six spent and eight corresponding new, off-the-shelf fluorescent lamp samples. The efficiency of several acid digestion methods for the determination of the elemental composition was studied and elemental mass fractions of K, Na, Y, Ca, Ba, Eu, Al, Pb, Mg, Hg, and P were measured. The study also finds aqua regia to be the best reagent for acid digestion. However, no significant difference in mercury distribution was found in the different phases of the new and spent fluorescent lamps. KW - Mercury KW - Rare earth elements KW - Hg distribution KW - Fluorescence lamps PY - 2017 DO - https://doi.org/10.1016/j.chemosphere.2016.11.104 SN - 0045-6535 SN - 1879-1298 VL - 169 SP - 618 EP - 626 PB - Elsevier AN - OPUS4-38481 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from waste streams N2 - Presentation of all relevant recovery technologies from wastes T2 - Vorlesung im Rahmen der integrierten Veranstaltung "Advanced Recycling Technologies" der TU Berlin CY - Berlin, Germany DA - 19.01.2016 KW - Phosphorus recovery PY - 2016 AN - OPUS4-35694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Adam, Christian T1 - Horizontale Düngemittelanalytik N2 - Die europäische Kommission (Generaldirektion Unternehmen und Industrie) hat kürzlich die Auswirkungen einer harmonisierten europäischen Düngemittelverordnung, einschließlich der technischen Durchführbarkeit und den umweltbezogenen, wirtschaftlichen und sozialen Auswirkungen einer solchen Gesetzgebung untersuchen lassen. Basierend auf diesen Ergebnissen soll nun die EU-Düngemittelverordnung (EG) 2003/2003 revidiert werden. Neben der Vielzahl von bestehenden und neuen Düngemitteltypen wie z.B. Phosphor-Recyclingdüngern soll die neue Verordnung auch organische Düngemittel und somit Matrices wie Klärschlamm, Gärrückstände und Wirtschaftsdünger regeln. Dies bedeutet, dass Parameter und Grenzwerte, die bisher in verschiedenen Verordnungen für verschiedene Matrices geregelt wurden, künftig gemeinschaftlich geregelt werden (Klärschlamm, Düngemittel) und weitere Matrices zusätzlich geregelt werden müssen (Phosphor-Recycling-Produkte, Produkte aus Klärschlamm/-aschen). Resultierend aus den aktuellen nationalen Entwicklungen insbesondere bezüglich des Ausstiegs aus der landwirtschaftlichen Klärschlammverwertung und im Hinblick auf die Bestrebungen hinsichtlich der Schonung natürlicher Ressourcen (z.B. ProgRess) ist zu erwarten, dass die Anzahl an Düngemitteln, die aus Recyclingmaterialien gewonnen werden, stark zunehmen wird. Recyclingdünger aus dem Stoffstrom Klärschlamm- bzw. Klärschlammasche werden zukünftig einen großen Anteil an diesen neuen Produkten ausmachen. Vor den angeführten Hintergründen ist es notwendig relevante und insbesondere bereits genormte Verfahren hinsichtlich ihrer Anwendbarkeit auf z.B. Klärschlamm/-aschen und daraus gewonnenen Recycling-Düngern sowie auf kommerzielle P-Düngemittel zu prüfen. Vor diesem Hintergrund wurde die BAM (FB 4.4) vom UBA mit einer Untersuchung beauftragt: UFOPLAN FKZ: 3714263200 „Untersuchung der Anwendbarkeit der im Rahmen des CEN-Projekts HORIZONTAL entwickelten Analyseverfahren auf Düngemittel und Klärschlamm/ -aschen“ Laufzeit: 01.07.2014 – 31.01.2017 T2 - Fachgespräch zum UFOPLAN-Projekt 3714 263200 CY - Berlin, Germany DA - 09.11.2016 KW - Düngemittelanalytik KW - Sekundärrohstoffdüngemittel KW - Robustheitstests PY - 2016 AN - OPUS4-38221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - A thermochemical process for fertilizer production from sewage sludge ashes investigated from lab to industrial scale N2 - Sewage sludge ashes (SSA) contain up to 13% P and are thus promising raw materials for fertilizer production. However, SSAs also contain heavy metals and the main P-bearing mineral phases whitlockite and aluminium phosphate are poorly bioavailable. We developed and patented a process that produces fertilizers from SSA addressing the above mentioned challenges. SSA is thermo-chemically treated at ~950°C under reducing conditions (reductive: dry sewage sludge) in a rotary kiln together with an alkali compound such as sodium or potassium sulfate, hydroxide or carbonate. Some undesired trace elements such as As, Hg, Pb and Cd are evaporated and separated via off gas treatment system. The poorly soluble phosphates are transformed into calcium alkali phosphates (CaNaPO4 or CaKPO4) that are not water soluble but completely soluble in neutral ammonium citrate solution (NAC). Pot experiments showed that the fertilizer performance of the treated SSA containing calcium alkali phosphates as the single P-bearing mineral phase was comparable to the performance of triple superphosphate. The PNAC-solubility of fertilizer products correlated very well with the resulting contents of calcium alkali phosphates and the P-uptake of plants in pot experiments. The effect of the ratio alkali/P on the PNAC-solubility was investigated by crucible experiments and trial series with a medium scale rotary kiln using different SSAs and alkali phosphates. The effects of operational parameters such as the temperature and the retention time were investigated as well as concurring side reactions of the alkali compounds e.g. with SiO2 present in SSA. The alkali/P ratio must be roughly adjusted at 2 to achieve 100% PNAC-solubility for a common type of SSA. A demonstration trial with an output of 2 t recycling fertilizer was carried out in an industrial rotary kiln (product output 30 kg/h). The PNAC-solubility of the product varied between 60% and 80% during the 4 days campaign showing that the transformation of the mineral P-phases to calcium alkali phosphates was not complete. This was observed although the amount of Na2SO4 additive was dosed according to the results of the pre-investigations. Structure analysis by XRD showed that besides the target compound CaNaSO4 also some Ca3(PO4)2 remained in the SSA as well as some unreacted Na2SO4 additive. Obviously, the conditions in the industrial rotary kiln were not optimal for the process showing that some process aspects have to be reconsidered for the scale-up. T2 - IPW8 - 8th International Phosphorus Workshop CY - Rostock, Germany DA - 12.09.2016 KW - Sewage sludge ash KW - Thermochemical treatment KW - Phosphorus recovery PY - 2016 AN - OPUS4-37375 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adam, Christian A1 - Peplinski, Burkhard A1 - Kley, Gerd A1 - Simon, Franz-Georg ED - Hilty, L. M. T1 - Thermo-chemical treatment of sewage sludge ashes aiming at marketable P-fertiliser products T2 - R'07 World Congress "Recovery of Materials and Energy for Resource Efficiency" CY - Davos, Switzerland DA - 2007-09-03 KW - P-recovery KW - Sewage sludge KW - Thermo-chemical treatment KW - Mineral phases KW - XRD PY - 2007 SN - 978-3-905594-49-2 SP - 14/1 EP - 14/7 PB - EMPA CY - Davos AN - OPUS4-16469 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Stephan, D. A1 - Meng, Birgit A1 - Simon, Sebastian A1 - von Werder, Julia T1 - Synthesis and characterisation of alites from reduced basic oxygen furnace slags N2 - Basic oxygen furnace slags (BOFS) are by-products of the steelmaking process. Several researchers have studied the production of Portland cement clinker and metallic iron from BOFS via a reductive treatment. In this study, we applied a carbothermal reduction of BOFS in a technical-scale electric arc furnace and characterised the clinker-like products. Those clinker-like non-metallic products (NMPs) had a chemical and mineralogical composition comparable to clinker for ordinary Portland cement (OPC) and contained large elongated alite crystals as major component. The pure NMPs reacted more slowly and achieved a lower degree of hydration compared with commercial OPC. If the reactivity of the products can be further increased by employing specific adaptations, it can be used as a full clinker substitute for OPC. Nevertheless, it is also an option to use the material without further modifications as a cement component or concrete addition, which contributes to the strength development in both cases. KW - BOFS KW - Hydration products KW - Thermal analysis KW - X-ray diffraction PY - 2021 DO - https://doi.org/10.1016/j.cemconres.2021.106518 SN - 0008-8846 VL - 147 SP - 6518 PB - Elsevier Ltd. AN - OPUS4-52939 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raniro, H.R. A1 - Teles, A.P. A1 - Pavinato, P.S. A1 - Adam, Christian T1 - Phosphorus solubility and dynamics in a tropical soil under sources derived from wastewater and sewage sludge N2 - Conventional phosphate fertilizers are usually highly water-soluble and rapidly solubilize when moistened by the soil solution. However, if this solubilization is not in alignment with plants demand, P can react with the soil colloidal phase, becoming less available over time. This is more pronounced in acidic, oxidic tropical soils, with high P adsorption capacity, reducing the efficiency of P fertilization. Furthermore, these fertilizers are derived from phosphate rock, a non-renewable resource, generating an environmental impact. To assess these concerns, waste-recycled P sources (struvite, hazenite and AshDec®) were studied for their potential of reducing P Fixation by the soil and improving the agronomic efficiency of the P fertilization. In our work, we compared the solubilization dynamics of struvite, hazenite, AshDec® to triple superphosphate (TSP) in a sandy clay loam Ferralsol, as well as their effect on solution pH and on soil P pools (labile, moderately-labile and non-labile) via an incubation experiment. Leaching columns containing 50 g of soil with surface application of 100 mg per column (mg col􀀀 1) of P from each selected fertilizer and one control (nil-P) were evaluated for 60 days. Daily leachate samples from the column were analyzed for P content and pH. Soil was stratified in the end and submitted to P fractionation. All results were analyzed considering p < 0.05. Our findings showed that TSP and struvite promoted an acid P release reaction (reaching pHs of 4.3 and 5.5 respectively), while AshDec® and hazenite reaction was alkaline (reaching pHs of 8.4 and 8.5 respectively). Furthermore, TSP promoted the highest P release among all sources in 60 days (52.8 mg col􀀀 1) and showed rapid release dynamic in the beginning, while struvite and hazenite showed late release dynamics and lower total leached P (29.7 and 15.5 mg col􀀀 1 P respectively). In contrast, no P-release was detected in the leachate of the AshDec® over the whole trial period. Struvite promoted the highest soil labile P concentration (7938 mg kg􀀀 1), followed by hazenite (5877 mg kg􀀀 1) and AshDec® (4468 mg kg􀀀 1), all higher than TSP (3821 mg kg􀀀 1), while AshDec® showed high moderately-labile P (9214 mg kg􀀀 1), reaffirming its delayed release potential. KW - Phosphate dynamics KW - Struvite KW - Wastewater KW - Sewage sludge ash KW - CaNaPO4 KW - P speciation PY - 2022 DO - https://doi.org/10.1016/j.jenvman.2021.113984 VL - 302 IS - Part A SP - 113984 PB - Elsevier Ltd. AN - OPUS4-53600 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Montag, D. A1 - Adam, Christian T1 - Rechtliche Vorgaben der Klärschlammverordnung und deren Auswirkungen auf die Phosphor-Rückgewinnung N2 - Im Abfalltechnik-Ausschuss der Bund/Länder-Arbeitsgemeinschaft Abfall (LAGA) wurde eine Vollzugshilfe zur Klärschlammverordnung erarbeitet, die nach Verabschiedung durch die Umweltministerkonferenz Mitte Mai 2020 als LAGA-Merkblatt M-39 veröffentlicht wurde. Im vorliegenden vierten Arbeitsbericht der DWA-Arbeitsgruppe KEK-1.1 werden verschiedene Aspekte der ab dem Jahr 2029 geltenden Regelungen aufgegriffen und damit einige Punkte des LAGA M-39 hinsichtlich der technischen Auswirkungen für den Kläranlagenbetreiber konkret ausgeführt. KW - Klärschlamm KW - Klärschlammverordnung KW - Phosphor-Rückgewinnung PY - 2022 SN - 1866-0029 VL - 5 IS - 69 SP - 406 EP - 413 PB - Gesellschaft zur Förderung der Abwassertechnik CY - Hennef AN - OPUS4-55009 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Hobohm, J. A1 - Kuchta, K. A1 - van Wasen, Sebastian A1 - Krüger, Oliver T1 - Recovery of rare earth elements - optimized elemental analysis of fluorescent lamp shredder waste N2 - Rare earth elements (REE) are a crucial component of fluorescence lamps. Several procedures have been developed to recovery these technological important elements. Nevertheless, actual REE recycling from fluorescence lamps is scarce so far (recovery rate of less than 1 %), with current recycling approaches concentrating on glass recovery. Since most recycling processes include several, also wet-chemical steps, a complete knowledge of the actual elemental composition of the respective mass flows is necessary for an efficient REE recovery. We tested seven different reagent mixtures for microwave-assisted digestion of fluorescent lamp shredder, including HF, HClO4, and H2O2. We determined the concentrations of 25 of the most relevant rare earth and other trace elements in the respective dilutions. Two independent digestions, one a mixture of perchlorid/nitric/hydrofluoric acid and the other aqua regia, showed the highest concentrations of 23 of these elements, excluding only Sn and Tb. The REE concentrations in the tested lamp shredder sample (stated in g/kg) were 10.2 (Y), 12.1 (La), 7.77 (Ce), 6.91 (Eu), 1.90 (Gd), and 4.11 (Tb). T2 - 5th International conference industrial and hazardous waste management - Crete 2016 CY - Chania, Crete, Greece DA - 27.09.2016 KW - Rare earth elements KW - Critical raw materials KW - Resource recovery KW - WEEE PY - 2016 SN - 978-960-8475-20-5 SN - 2241-3138 SP - 1 EP - 4 AN - OPUS4-37761 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Thermochemische Aufbereitung von Klärschlammasche zu Phosphordünger T2 - GVC-Arbeitssitzung CY - Berlin, Germany DA - 2004-04-26 PY - 2004 AN - OPUS4-3505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Einsatz des Lichtbogenofens für die Wertstoffrückgewinnung aus Reststoffen - Forschungsthemen der BAM T2 - Sitzung des Arbeitskreises "Lichtbogenofenbetrieb" des Bundesverbandes der Deutschen Gießerei-Industrie (BDG) CY - Castrop-Rauxel, Germany DA - 2011-04-13 PY - 2011 AN - OPUS4-23593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herbeck, Maximilian T1 - Metal recovery by reductive melting of red mud N2 - Investigation about metal recovery from red mud by reductive smelting. T2 - Exchange of good practices on metal by-products recovery CY - Brussels, Belgium DA - 12.11.2015 KW - Red mud KW - Metal recovery KW - Reductive smelting PY - 2015 AN - OPUS4-35691 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Adam, Christian T1 - Sewage sludge ashes - waste or valuable resource N2 - There is a growing concern of the direct use of contaminated sewage sludge in agriculture due possible environmental and health hazards. Thus, incineration of the sludge and thus increasing amounts of sewage sludge ashes (SSA) are to be expected in the future. SSA contains considerable amounts of phosphorus (P) and technology metals that might be recovered as secondary raw materials. Since the EU for instance depends completely on the import of rock phosphate needed for fertilizer production, alternative sources for P are in order. Furthermore, rock phosphate is often contaminated with heavy metals like Cd and U, leading to health and environmental hazards. P recovered from SSA might diminish these problems. To determine the possible recovery potential of P and technology metals from SSA, we conducted a survey of German mono incineration facilities and analyzed the respective SSA for their elemental composition. More than 95% of the emerging SSA was monitored. Results indicate a P recovery potential of 18,000 t/a (up to 13% of the annual P demands for fertilizer production). The concentrations of Cd and U in SSA are one to two Orders of magnitude lower than in rock phosphate and could help to reduce possible hazards. T2 - 4th International conference industrial and hazardous waste management (Crete 2014) CY - Chania, Crete, Greece DA - 02.09.2014 KW - Sewage sludge ash KW - Resource recovery KW - Phosphorus KW - Technology metals PY - 2014 SN - 978-960-8475-20-5 SN - 2241-3138 SP - 1 EP - 8 AN - OPUS4-31396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Kley, Gerd A1 - Simon, Franz-Georg A1 - Lehmann, Annekatrin ED - Filibeli, A. ED - F. Dilek Sanin, ED - Ayol, A. ED - Selim L. Sanin, T1 - Recovery of nutrients from sewage sludge - Results of the European research-project SUSAN T2 - IWA-Specialist Conference "Facing Sludge Diversities: Challenges, Risks and Opportunities" CY - Antalya, Turkey DA - 2007-03-28 KW - Phosphorus recovery KW - Sewage sludge ash KW - Thermo-chemical treatment KW - Fertiliser PY - 2007 N1 - Serientitel: Journal of environmental science and health : Part A, Toxic/hazardous substances & environmental engineering – Series title: Journal of environmental science and health : Part A, Toxic/hazardous substances & environmental engineering IS - 43.2008,13 SP - 297 EP - 305 PB - Taylor & Francis CY - Philadalphia, PA AN - OPUS4-16468 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Leimkötter, D. A1 - Hermann, L. A1 - Emter, J. A1 - Brey, C. A1 - Künstler, J. A1 - Hartmann, S. A1 - Krannich, G. A1 - Moggert, N. A1 - Kurz, P. A1 - Eder, C. A1 - Grimm, B. A1 - Adam, Christian ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Success-Story CaNaPO4: Erfolgreiche REACH Registrierung und Inbetriebnahme großtechnischer Anlagen N2 - The Sewage Sludge Ordinance (AbfKlärV), which was amended in 2017, obligate the recovery of phosphorus from sewage sludge and sewage sludge ash from 2029 and 2032, respectively. Thermal disposal of sewage sludge has established itself as the preferred method of disposal, and the capacities of mono-incineration plants are being continuously expanded. Plants for phosphorus recovery, on the other hand, are currently still mainly in the construction, piloting, or commissioning phase. It is estimated that the plant capacities for P recovery planned today will not even be able to cover a quarter of the volume of these ashes in 2029. Therefore, temporary storage of the remaining ashes is currently being discussed to retrieve it later and process it in the P recovery plants, which will then be sufficiently available. It is currently unclear how such interim or long-term storage (> 1 year) should be organized. In addition to legal (fee) issues, the assessment of the technical feasibility of retrievability and the phosphorus recovery potential of landfilled ash remains open. The Institute of Environmental Engineering (ISA) at RWTH Aachen University and the Federal Institute for Materials Research and Testing (BAM) are jointly investigating five deposited ashes that have been dug out and were provided by three landfill operators. The investigations focus on the physical and chemical characterization of these landfilled ashes and its P recovery potential during treatment in thermochemical and wet chemical processes. These results are evaluated in comparison with “fresh,” i.e., non-landfilled sewage sludge ash samples of comparable origin in order to determine the influence of storage. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Phosphor KW - Recycling KW - Thermochemisch KW - Dünger KW - Großtechnik PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 236 EP - 256 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-64833 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Enzymkatalysierte Synthese von Schmierstoffen aus Altfett N2 - Im Rahmen eines vom BMBF geförderten KMU-Innovativ Forschungsprojekts (KKZ 0316199B) konnte in Kooperation mit der Firma Greibo Chemie GmbH ein bio-katalysierter Prozess zur Hydrolyse und Veresterung von gastronomischen Altfetten etabliert werden. Unter Anwendung des Enzyms Candida antarctica lipase-A (CAL-A) kann dieser Prozess mit einem teilweise wässrigen Medium durchgeführt werden was prozesstechnisch einige Vorteile mit sich bringt. Im Gegensatz zu anderen Acyltransferasen ist die CAL-A nicht nur in der Lage die Alkoholyse zu katalysieren sondern auch Fettsäuren zu verestern. Dies eröffnet eine breitere Anwendung des Prozesses auf weitere Produktgruppen und Abfallströme. Es wurden Optimierungen mit modifizierten Enzymen und verschiedenen Fetten und Alkoholen vorgenommen. Des Weiteren wurden die verfahrenstechnischen Parameter optimiert und ein Scale-up auf den 0,5 Tonnen Maßstab durchgeführt. Die aus dem Prozess resultierenden Fettsäureester eignen sich als Motoren- oder Hydraulikbasisöle sowie als Metallbearbeitungsöle. Im Vergleich zu den Mineralölkosten von ca. 1,0 - 1,5 € pro kg muss bei einer Umstellung eines Hydrauliköls auf Fettsäureester (konventionell hergestellt) allerdings bei einem Preis von 3 – 5 € pro kg mit Mehrkosten bei gleichbleibendem Verbrauch gerechnet werden. Für die erfolgreiche Markteinführung müssten vermutlich die durchaus vorhandenen ökologischen Vorteile der Altfett-basierten Produkte beworben werden. T2 - Deutsche Biotechnologietage 2016 CY - Leipzig DA - 26.04.2016 KW - Altfett KW - Enzymkatalyse PY - 2016 AN - OPUS4-35970 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Martins, Isabel ED - Ulsen, Carina ED - Angulo, Sergio Cirelli T1 - Secondary building materials from construction and demolition waste: environmental benefits and costs N2 - Due to the large quantities of construction and demolition waste (CDW) in Europe, its reuse or recycling is of particular importance. Although several countries already recycle high amounts of CDW, the use as secondary raw materials is often limited by inferior building material properties. Specific characteristics, like high porosity and low density are caused by hardened cement paste in crushed concrete and the content of mortar and plaster in brick debris. Impurities like wood or gypsum and also harmful substances like organic pollutants may be a major problem for a reuse and should be minimized. Therefore unwanted materials and impairing substances have to be separated from the secondary building material stream. This can be done during the demolition process by using techniques for selective dismantling or during the subsequent treatment of the resulting rubble. Since almost all processing steps are associated with environmental impacts, the benefits of saving natural resources by applying secondary building materials should be weighed carefully. An environmental performance evaluation was undertaken to assess different techniques for reducing gypsum in recycled concrete aggregates, aiming at a minimization of elutable sulfates. These results were compared to the environmental impacts of the extraction of natural aggregates for concrete. T2 - "Progress of recycling in the built environment" CY - Sao Paulo, Brazil DA - 03.08.2015 KW - CDW processing KW - Demolition/selective dismantling KW - Gypsum KW - Environmental evaluation KW - Bauschuttaufbereitung KW - Ökobilanzielle Bewertung PY - 2015 UR - http://www.rilem.org/gene/main.php?base=500218&id_publication=449&id_papier=10699 SN - e-ISBN: 978-2-35158-158-2 SP - 192 EP - 199 CY - Paris, France AN - OPUS4-38170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adam, Christian A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermal treatment of municipal sewage sludge aiming at marketable P-fertilisers N2 - Municipal sewage sludge is a carrier of nutrients – most important phosphorus (P) – but also contains organic pollutants and heavy metals. A two steps thermal treatment is suggested based on 1. mono-incineration of sewage sludge under destruction of organic pollutants and 2. thermochemical treatment of the resulting ashes to remove heavy metals and increase P-bioavailability. The targeted products are marketable P-fertilisers. The thermochemical treatment was investigated in a gas tight lab-scale rotary furnace. Seven sewage sludge ashes of different origin and composition and one residue from gasification of sewage sludge were mixed with a chlorine donor (e.g. MgCl2) and thermochemically treated under systematic variation of operational parameters. The distributions of the heavy metals between solid and gas phase were determined. The heavy metals concentrations of the treated ashes met the legislative limits in most cases. The products from thermochemical treatment are suited raw materials for P-fertiliser production. Relevant process parameters such as temperature, type and concentration of Cl-donor and retention time were optimised for the thermochemical treatment step. KW - Sewage sludge KW - Mono-incineration KW - Ash treatment KW - Thermochemical treatment KW - Phosphorus-fertiliser PY - 2007 SN - 1345-9678 SN - 1347-5320 VL - 48 IS - 12 SP - 3056 EP - 3061 PB - Japan Institute of Metals CY - Sendai AN - OPUS4-16647 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorrückgewinnung im Bereich der kommunalen Abwasserreinigung T2 - ProcessNet Sitzung des Fachausschusses "Abfallbehandlung und Wertstoffrückgewinnung" CY - Fichtenau, Germany DA - 2010-10-07 PY - 2010 AN - OPUS4-22401 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Environmental evaluation of different ways to produce recycled concrete aggregates T2 - SUM 2014 - Symposium on Urban Mining CY - Bergamo, Italy DA - 2014-05-19 PY - 2014 AN - OPUS4-30784 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herzel, Hannes A1 - Krüger, Oliver A1 - Hermann, L. A1 - Adam, Christian T1 - Sewage sludge ash - A promising secondary phosphorus source for fertilizer production N2 - Sewage sludge incineration is extensively practiced in some European countries such as the Netherlands, Switzerland, Austria and Germany. A survey of German sewage sludge ash showed that the recovery potential is high, approx. 19,000 t of phosphorus per year. However, the survey also discovered that the bioavailability of phosphorus in the sewage sludge ash is poor and that more than half of the ashes cannot be used as fertilizers due to high heavy metal content. A new thermochemical process for sewage sludge ash treatment was developed that transforms the ash into marketable fertilizer products. Sewage sludge ash was thermochemically treated with sodium and potassium additives under reducing conditions, whereby the phosphate-bearing mineral phases were transformed into plant available phosphates. High P-bioavailability was achieved with a molar Na/P ratio > 1.75 in the starting materials. Sodium sulfate, carbonate and hydroxide performed comparably as additives for this calcination process. Potassium carbonate and -hydroxide have to be added in a molar K/P ratio > 2.5 to achieve comparable P-solubility. The findings of the laboratory scale investigations were confirmed by an industrial demonstration trial for an ash treatment with sodium sulfate. Simultaneously, the volatile transition metal arsenic (61% removal) as well as volatile heavy metals such as cadmium (80%), mercury (68%), lead (39%) and zinc (9%) were removed via the off-gas treatment system. The product of the demonstration trial is characterized by high bioavailability and a toxic trace element mass fraction below the limit values of the German fertilizer ordinance, thus fulfilling the quality parameters for a P-fertilizer. KW - Sewage sludge ash KW - Phosphorus recovery KW - Thermochemical treatment KW - Reducing conditions KW - Heavy metal evaporation KW - Bioavailability KW - Sodium sulfate PY - 2016 DO - https://doi.org/10.1016/j.scitotenv.2015.08.059 SN - 0048-9697 SN - 1879-1026 IS - 542 SP - 1136 EP - 1143 PB - Elsevier CY - Amsterdam AN - OPUS4-34165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Weimann, Karin A1 - Matyschik, Jan A1 - Adam, Christian A1 - Schulz, T. A1 - Linß, E. A1 - Müller, A. T1 - Optimierung des Rückbaus/Abbruchs von Gebäuden zur Rückgewinnung und Aufbereitung von Baustoffen unter Schadstoffentfrachtung (insbes. Sulfat) des RCMaterials sowie ökobilanzieller Vergleich von Primär- und Sekundärrohstoffeinsatz inkl. Wiederverwertung N2 - Aufgrund der großen Massenströme ist das Recycling von Baurestmassen von besonderer Bedeutung für die Schonung von natürlichen Ressourcen. Eine wichtige Voraussetzung für ein hochwertiges Recycling, wie z.B. eine Wiederverwertung von aufbereitetem Bauschutt/Altbeton als rezyklierte Gesteinskörnung im Hochbau, ist die Einhaltung von Grenzwerten für Stör- und Schadstoffe. Dabei steht der Sulfatgehalt im Eluat von Bauschutt besonders im Fokus. In der vorliegenden Studie wird untersucht, wie durch die Optimierung von Abbrucharbeiten und Bauschuttaufbereitung hochwertige Gesteinskörnungen aus Altbeton gewonnen werden können. Anhand von Literatur- und Datenrecherchen werden zunächst Sulfatquellen in Gebäuden sowie verfügbare Abbruch- und Aufbereitungstechniken zusammengestellt. Am Beispiel von unterschiedlichen Gebäudetypen werden Szenarien für selektiven und nicht selektiven Abbruch (Schwerpunkt: Sulfatentfachtung) in Hinblick auf ihre Umweltwirkungen ökobilanziell bewertet. Ergänzt werden diese Bewertungen durch Untersuchungen an realen Bauschuttmaterialien und Abbruchprojekten. Auf dieser Basis werden Handlungsempfehlungen für die Gewinnung von hochwertigen RC-Gesteinskörnungen erarbeitet und diskutiert.----------------------------------------------------------------------------------------- Due to the large-scale mass flow of construction and demolition wastes, the recycling of those residues is of particular importance for the conservation of natural resources. An important requirement for recycling on a high level, like the reuse of crushed concrete as recycled concrete aggregate, is the observation of limits for hazardous substances and impurities. This study is focusing on the reduction of sulphates in the eluate of crushed concrete. An investigation of possibilities to optimize demolition and dismantling as well as treatment of crushed concrete with the objective of gaining recycled concrete aggregates of high quality. Based on a literature research and a data review the origins of sulfates in buildings and also the availability of techniques for demolition and treatment of crushed concrete are listed and evaluated. Using the examples of different building types scenarios for selective dismantling and non-selective demolition (focused on reducing suphates) are evaluated in terms of affecting the environment. In addition samples from real demolition construction sites and plants for treatment of construction rubble were investigated. Based on these results recommendations for the production of high quality recycled concrete aggregates are worked out. KW - Bauschuttaufbereitung KW - Abbruch KW - Ökobilanzielle Bewertung KW - RC-Beton KW - Gips KW - Abbruchverfahren KW - Hochwertiges Recycling KW - Ökobilanzielle Betrachtung KW - Sulfatentfachtung KW - Demolition/dismantling KW - Treatment of C&D wastes KW - High-grade recycling KW - Environmental LCA KW - Reduction of sulphates PY - 2012 UR - http://www.umweltbundesamt.de/publikationen/optimierung-des-rueckbausabbaus-von-gebaeuden-zur SN - 1862-4804 SP - 1 EP - 227 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-26999 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Adam, Christian T1 - Ressourcen aus Abfall T1 - Resources from waste N2 - Die Beseitigung unbehandelter Abfälle auf Deponien gehört der Vergangenheit an, nicht nur weil Verordnungen diese Praxis verbieten, sondern auch, weil wegen steigender Preise für Rohstoffe und sinkender Gehalte in Erzen auch in Abfällen nach Alternativen gesucht wird. In den Aschen aus Hausmüllverbrennungsanlagen können mit einfachen Verfahren Metalle zurückgewonnen werden. Mit dem Phosphor aus Klärschlammaschen können Düngemittel hergestellt und so natürliche Ressourcen geschont werden. In beiden Fällen ist die Anreicherung der Wertstoffe durch den Verbrennungsprozess vorteilhaft, da die Effizienz von Recyclingprozessen stark von der Konzentration im Ausgangsgut abhängig ist. N2 - Disposal of untreated waste has come to end due to new legislation in this field. Furthermore as a response to increasing prices for primary raw materials and decreasing ore concentrations products from waste treatment display a source for secondary raw materials. Elemental metals can be easily separated from municipal solid waste incineration bottom ash. Fertilizers can be produced using phosphate from sewage sludge ashes thus preserving natural resources. In both cases the enrichment taking place in the incineration process facilitates the resource recovery, because the efficiency of recycling processes is dependent on the concentration of the input material. KW - Klärschlammaschen KW - NE-Metalle KW - Phosphor KW - Rostaschen KW - Bottom ash KW - Nonferrous metals KW - Phosphorus KW - Sewage sludge ash PY - 2012 DO - https://doi.org/10.1002/cite.201100189 SN - 0009-286X SN - 1522-2640 VL - 84 IS - 7 SP - 999 EP - 1004 PB - Wiley-VCH CY - Weinheim AN - OPUS4-26209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adam, Christian A1 - Peplinski, Burkhard A1 - Michaelis, Matthias A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermochemical treatment of sewage sludge ashes for phosphorus recovery N2 - Phosphorus (P) is an essential element for all living organisms and cannot be replaced. Municipal sewage sludge is a carrier of phosphorus, but also contains organic pollutants and heavy metals. A two-step thermal treatment is suggested, including mono-incineration of sewage sludge and subsequent thermochemical treatment of the ashes. Organic pollutants are completely destroyed by mono-incineration. The resulting sewage sludge ashes contain P, but also heavy metals. P in the ashes exhibits low bioavailability, a disadvantage in farming. Therefore, in a second thermochemical step, P is transferred into mineral phases available for plants, and heavy metals are removed as well. The thermochemical treatment was investigated in a laboratory-scale rotary furnace by treating seven different sewage sludge ashes under systematic variation of operational parameters. Heavy metal removal and the increase of the P-bioavailability were the focus of the investigation. The present experimental study shows that these objectives have been achieved with the proposed process. The P-bioavailability was significantly increased due to the formation of new mineral phases such as chlorapatite, farringtonite and stanfieldite during thermochemical treatment. KW - P-recovery KW - Sewage sludge ash KW - Thermochemical treatment KW - Mineral phases KW - X-ray diffraction PY - 2009 DO - https://doi.org/10.1016/j.wasman.2008.09.011 SN - 0956-053X VL - 29 IS - 3 SP - 1122 EP - 1128 PB - Pergamon Press CY - New York, NY AN - OPUS4-18605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Kabbe, Ch. T1 - Phosphorrückgewinnung und Recycling aus dem Abwasser N2 - Phosphorrecycling sollte nicht isoliert praktiziert werden, sondern im Kontext der spezifischen Abwasserbehandlung und der Betrachtung weiterer Nährstoffe wie Stickstoff und Kalium. Hohe Rückgewinnungsquoten um jeden Preis sind nicht immer zielführend und u.U. sogar schädlich für die Kreislaufwirtschaft. Es sollte eine Kombination verschiedener Ansätze je nach vorhandener Infrastruktur verfolgt werden. Fällungsverfahren (Struvit) sind geeignet kostengünstig kleine Mengen Phosphor zurückzugewinnen. Für ein umfassendes P-Recycling muss die Rückgewinnung aus der Asche erfolgen. T2 - 20. Leibnitz-Conference of Advanced Science - "Ressourcenmanagement als Beitrag zur gesicherten Rohstoffversorgung" CY - Lichtenwalde, Saxony, Germany DA - 19.05.2016 KW - Recycling KW - Phosphor KW - Abwasser PY - 2016 AN - OPUS4-36319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schick, J. A1 - Kratz, S. A1 - Hermann, L. T1 - Phosphorus recovery by thermochemical treatment of sewage sludge ash T2 - 5th IWA Leading-Edge Conference on Water and Wastewater Technologies CY - Zürich, Switzerland DA - 2008-06-01 KW - Phosphorus recovery KW - Sewage sludge ash KW - Thermochemical treatment KW - Fertiliser KW - Greenhouse pot experiments PY - 2008 SP - 1 EP - 10 PB - International Water Association (IWA) CY - London AN - OPUS4-17568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kratz, S. A1 - Beerbaum, B. A1 - Elsner, H. A1 - Reuvers, J. A1 - Dockhorn, T. A1 - Rechberger, H. A1 - Werner, W. A1 - Knudsen, L. A1 - Flachowsky, G. A1 - Rodehutscord, M. A1 - Adam, Christian A1 - Steingrobe, B. A1 - Schick, J. A1 - Albert, E. A1 - Leinweber, P. A1 - Ekardt, F. A1 - Embert, G. T1 - Ressourcen schonender Einsatz von Phosphor in der Landwirtschaft - Symposium des Institutes für Pflanzenbau und Bodenkunde des JKI in Braunschweig - eine Synopse KW - Klärschlamm KW - Phosphor KW - Ressource KW - Klärschlammasche KW - P-Düngemittel KW - Demonstrationsanlage PY - 2009 SN - 1867-0911 SN - 1867-0938 SN - 1865-4371 VL - 61 IS - 2 SP - 69 EP - 71 PB - Ulmer CY - Stuttgart AN - OPUS4-18928 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ante, A. A1 - Trumpler, A. A1 - Niermann, S. A1 - Decker, Renate A1 - Hermann, L. A1 - Adam, Christian T1 - SUSAN - Sustainable and safe re-use of municipal sewage sludge for nutrient recovery KW - Sewage sludge KW - Phosphorus KW - Recycling KW - Thermochemical treatment KW - Heavy metal removal KW - Large scale consideration PY - 2010 SN - 0016-3651 VL - 151 IS - 13 SP - 78 EP - 84 PB - Oldenbourg-Industrieverl. CY - München AN - OPUS4-22097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adam, Christian T1 - SUSAN - Sustainable and safe re-use of municipal sewage sludge for nutrient recovery N2 - The SUSAN-project aimed at developing a sustainable and safe strategy for nutrient recovery from sewage sludges using thermal treatment. Mono-incineration of the sludges completely destructs the organic pollutants in a first step. The incineration residues are ashes with a high phosphorus content that still contain heavy metal compounds above the limits for agricultural use. Furthermore, phosphorus in the ashes exhibits low bioavailability - a disadvantage in farming. Therefore, in a second thermochemical step heavy metals are removed and phosphorus transferred into mineral phases available for plants. The principle of the SUSAN-project is the separation of the small heavy metals fraction from the ashes to receive a phosphorus rich product suited as raw material for fertilisers that also contains SiO2, CaO, Al2O3, Fe2O3, MgO and K2O. The thermochemical process is based on evaporation of volatile heavy metal chlorides at 850 - 1000 °C. The sewage sludge ashes are mixed with chlorine donors such as MgCl2 or KCl, grained and treated in a thermal aggregate e.g. a rotary furnace. At the same time a transfer of non soluble P-compounds into Mineral phases available for plants takes place. Besides technological development of the thermochemical process, the products fertilisation performance, the product design, the market for the products and the sustainability of the whole process chain are emphasised in the SUSAN-project. KW - Nutrient recovery KW - Sewage sludges KW - Sludge disposal KW - Sustainability KW - Environmental pollution PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-391607 UR - http://cordis.europa.eu/result/rcn/46724_en.html SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Weimann, Karin A1 - Adam, Christian T1 - RECDEMO - Vollständige Verwertung der Sandfraktion aus dem Bauschuttrecycling N2 - In dem Projekt sollten die Aufbereitung der Betonbrechsandfraktion aus Bauschutt mittels eines Nassverfahrens zu einer geeigneten Gesteinskörnung für die Betonherstellung sowie die vollständige Verwertung der bei diesem Verfahren anfallenden Reststoffe demonstriert werden. Der im Rahmen der geordneten Vorsortierung mit zahlreichen Schritten zur Qualitätssicherung hergestellte Betonbrechsand war qualitativ hochwertig und wies nur geringe Schadstoffgehalte auf. Für die Nassaufbereitung des Betonbrechsands wurde vom Projektpartner Allmineral der Prototyp einer Sandsetzmaschine zur Dichtetrennung designt und konstruiert. Diese Sandsetzmaschine wurde für die umfangreichen Betonbrechsandversuche in die Aufbereitungsanlage der BAM integriert. Begleitend zur Aufbereitung wurden die eingesetzten Materialien, Bauschutt und Prozesswasser, sowie die Austragsprodukte chemisch-physikalisch und mineralogisch untersucht. Die anschließenden Baustoffuntersuchungen zeigten, dass durch das im Demonstrationsprojekt angewandte Nassaufbereitungsverfahren eine deutliche Verbesserung der Materialeigenschaften des Betonbrechsandes erzielt werden konnte. Die Qualität von Natursteinkörnungen wurde (z.B. aufgrund von Kornschädigungen durch den Bruch des Altbetons und noch verbleibende Zementanhaftungen) gleichwohl nicht erreicht. Gerade die Betonprüfungen (mit Anteilen von bis zu 50% Betonbrechsand an der gesamten Gesteinskörnung) haben jedoch gezeigt, dass es dennoch sehr wohl möglich wäre, größere Mengen von aufbereitetem Betonbrechsand in der Betonherstellung zu verwerten und so im Sinne der Nachhaltigkeit den Verbrauch von natürlichen Sandvorkommen zu reduzieren. Die bei der Nassaufbereitung des Betonbrechsands anfallenden Restsstoffe, nämlich die Fraktionen Leichtgut und Feinstfraktion wurden separat erfasst und bilanziert. Diese Materialien wurden auf die Eignung als Kompostzugabe in Hinblick auf Schadstoffanreicherungen und Pflanzenverträglichkeit untersucht (Projektpartner Deisl). Nach der Kompostierung in Rotteboxen wurden Wachstumsversuche mit dem Referenzgewächs Kresse (Kressetest nach ÖNORM) mit zufriedenstellenden Ergebnissen durchgeführt. Die Reststoffe Feinstgut und Leichtgut aus dem Nassaufbereitungsprozess könnten – sofern die Schadstoffgehalte nachweislich unter den vorgegebenen Grenzwerten liegen – als Zugabe zur Vererdung in der Kompostierung eingesetzt werden. KW - Reststoffe KW - Betonbrechsand KW - Bauschuttaufbereitung KW - Betonherstellung PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-390203 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39020 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Adam, Christian T1 - Potenzialermittlung der in Deutschland anfallenden Klärschlammaschen - Mögliche Phosphor- und Metallrückgewinnung N2 - In Europa fallen jedes Jahr mehr als 10 Millionen Tonnen Klärschlamm an (Trockenmasse), etwa 2 Millionen davon in Deutschland, Bild 1 zeigt die Entwicklung der Klärschlammentsorgung in Deutschland. Nach dem Deponierungsverbot hat die Verbrennung des Klärschlamms stetig zugenommen. Die Verwendung im Landschaftsbau bzw. als Düngemittel ist nach einem Maximum um die Jahrtausendwende herum zugunsten der Verbrennung zurückgegangen, so dass heute jeweils etwa die Hälfte des Klärschlamms verbrannt und in der Landwirtschaft genutzt wird. Der Anteil an verbranntem Klärschlamm wird in Zukunft vermutlich weiter steigen. Ein wesentlicher Grund dafür ist die zunehmende Besorgnis über Schadstoffe im Klärschlamm, die Mensch und Umwelt schädigen könnten. Neben verschiedenen organischen und anorganischen Schadstoffen handelt es sich insbesondere um Emerging Pollutants of Concern (EMPOC) wie Antibiotika und Kosmetika. T2 - 8. Klärschlammtage CY - Fulda, Germany DA - 04.06.2015 PY - 2013 SP - 1 EP - 5 AN - OPUS4-33344 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg A1 - Adam, Christian T1 - RecArc - Verwertung von Rückständen aus der Metallurgie mit der Lichtbogentechnologie N2 - In dem Projekt soll die vollständige Wiederverwertbarkeit der Schlacke und ihrer Bestandteile demonstriert werden. Dazu gehören die vollständige Rückgewinnung der metallischen Phase, die in die Edelstahlherstellung zurückgeführt werden kann, sowie die Aufwertung der mineralischen Fraktion, die ihre uneingeschränkte Verwendung als Zementzumahlstoff oder mineralischer Baustoff erlaubt. Bei geeigneter Prozessführung des elektrischen Lichtbogenofens können durch „reduzierendes Schmelzen“ die chromhaltigen Wertstoffe zusammen mit anderen Schwermetallen zu 97% in einer Metalllegierung angereichert und separiert werden. Diese kann als Rohstoff in der Metallurgie eingesetzt werden. Der Chromgehalt der mineralischen Komponte der Schlacke konnte von ca. 3% auf unter 0,1% verringert werden. Die mineralische Fraktion lässt sich durch entsprechende Zuschläge während des Schmelzbetriebes und eine anschließende Granulation der schmelzflüssigen Phase zu einem Material aufwerten, das in seiner Zusammensetzung und seinen Eigenschaften typischen Zementkomponenten entspricht und als Rohstoff in der Zementproduktion eingesetzt werden kann. Dafür müssen allerdings noch die rechtlichen Voraussetzungen geschaffen werden, da der Rohstoffeinsatz gerade im Zement strengen Auflagen unterliegt und die Zemente bestimmte Normen erfüllen müssen. Durch die in RECARC aufgezeigte Möglichkeit der Wiederverwertung können somit Stoffkreisläufe geschlossen werden, die ansonsten zu einem Verlust wertvoller Rohstoffe führen. Vor allem die steigenden Rohstoffkosten, aber auch die immer stärker limitierten CO2-Emissionen zeigen die hohe Relevanz im Umgang mit metallurgischen Reststoffen. Eine Überführung des in RECARC demonstrierten Verfahrens in die Industrie könnte einen wichtigen Beitrag zur nachhaltigen Schonung der natürlichen Ressourcen und der Umwelt leisten. KW - Chrom KW - Lichtbogenofen KW - Recycling KW - Rückgewinnung KW - Schlacke PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-390197 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39019 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, S. A1 - Herzel, Hannes A1 - Adam, Christian A1 - Montag, D. ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Langzeitlagerung von Klärschlammaschen ab 2029? Erste Erfahrungen zur Phosphorrückgewinnung aus deponierten Klärschlammverbrennungsaschen N2 - Das Institut für Siedlungswasserwirtschaft (ISA) der RWTH Aachen University sowie die Bundesanstalt für Materialforschung und -prüfung (BAM) untersuchen gemeinsam fünf deponierte KSA, die von drei Deponiebetreibern ausgebaut und zur Verfügung gestellt wurden sind. Im Fokus der Untersuchungen stehen die physikalische und chemische Charakterisierung der deponierten KSA sowie deren P-Rückgewinnungspotenzial bei der Behandlung in thermochemischen sowie nasschemischen Verfahren. Diese Ergebnisse werden im Vergleich mit „frischen“, also nicht deponierten KSA-Proben vergleichbarer Herkunft bewertet, um so den Einfluss der Lagerung auf die KSA zu erfassen. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Klärschlammasche KW - Recycling KW - Deponie KW - Monoverbrennung PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 192 EP - 202 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-65017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Joachim A1 - Adamczyk, Burkart A1 - Ebert, Dominik A1 - Ehrenberg, Andreas A1 - Schraut, Katharina A1 - Algermissen, David A1 - Adam, Christian T1 - Usage of BOF slag and next generation EAF slag in the cement industry N2 - When the transformation of its production routes, which the European steel industry aims to complete within the next two decades, is accomplished, increased amounts of EAF slag will be generated. In most cases the BF/BOF production route is intended to be substituted by a DRI/EAF combination. But in some cases only the BF will be substituted by a DRI/SAF (smelter) combination and the BOF process remains. Then BOF slags will remain, too. BAM and FEhS cooperate together with further research and industry partners in two research projects dealing on the one hand with the utilisation of modified BOF slag as a cement clinker substitute ("SlagCEM") and on the other hand with the use of modified and granulated EAF slag as granulated blast furnace slag (GBS) substitute ("DRI-EOS"). T2 - 9th International Slag Valorisation Symposium CY - Leuven, Belgium DA - 08.04.2025 KW - Steel slags KW - Basic oxygen furnace (BOF) KW - Electric arc furnace (EAF) KW - Cement KW - Slag valorisation PY - 2025 SP - 187 EP - 191 AN - OPUS4-64713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Leers, K. A1 - Arnold, U. A1 - Herzel, Hannes A1 - Adam, Christian A1 - Burkhardt, J. T1 - Thermochemically Treated Sewage Sludge Ash From Pilot-Scale Production as P-Fertilizer for Spring Wheat and Maize in Different Soil Conditions N2 - Background P-fertilizers made from sewage sludge ash (SSA) may be suitable substitutes for rock phosphate (RP)-based fertilizers and contribute to sustainable use of waste. In this context, the thermochemical AshDec treatment of SSA (TC-SSA) has been continuously improved and has emerged as a possible method to produce plant-available and low-pollutant P-fertilizers. Aim Evaluation of the P-fertilizer efficacy of TC-SSA produced in pilot trials in vegetation experiments with different plants, soils, and fertilizer doses. Methods TC-SSA was tested in pot experiments for spring wheat and maize on different soils and at two doses (0.2 and 0.4 g fertilizer P pot−1) and is compared to untreated SSA (USSA), RP, Struvite, triple superphosphate (TSP), and a control without P-fertilization (Zero P). Pot experiments are complemented by an analysis of fertilizer P-solubility. Results P-solubility of SSA with different extraction methods increased due to the thermochemical treatment, whereas the water-insoluble property remained. In contrast to RP or USSA, TC-SSA enriched calcium–acetate–lactate extractable soil P to the same extent as TSP. Plant biomass and P-uptake increased with TC-SSA compared to Zero P, RP, and USSA and were in most cases equal to TSP fertilization under different soil conditions. In contrast, the effects of RP and USSA varied among soils but, mostly, did not exceed plant biomass and P-uptake of the unfertilized control. Conclusion TC-SSA has an increased fertilizer efficacy compared to USSA and is an effective P-fertilizer for spring wheat and maize in different soil conditions. KW - Phosphorus KW - Fertilizer KW - Thermochemical KW - Maize PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-648251 DO - https://doi.org/10.1002/jpln.70035 SN - 1522-2624 VL - 189 IS - 1 SP - 81 EP - 93 PB - Wiley-VCH AN - OPUS4-64825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Firma Naue GmbH & Co. KG, Espelkamp. KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636742 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-63674 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 5. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 5. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Firma HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636732 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-63673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jovičević-Klug, Matic A1 - Souza Filho, Isnaldi R. A1 - Springer, Hauke A1 - Adam, Christian A1 - Raabe, Dierk T1 - Green steel from red mud through climate-neutral hydrogen plasma reduction N2 - AbstractRed mud is the waste of bauxite refinement into alumina, the feedstock for aluminium production1. With about 180 million tonnes produced per year1, red mud has amassed to one of the largest environmentally hazardous waste products, with the staggering amount of 4 billion tonnes accumulated on a global scale1. Here we present how this red mud can be turned into valuable and sustainable feedstock for ironmaking using fossil-free hydrogen-plasma-based reduction, thus mitigating a part of the steel-related carbon dioxide emissions by making it available for the production of several hundred million tonnes of green steel. The process proceeds through rapid liquid-state reduction, chemical partitioning, as well as density-driven and viscosity-driven separation between metal and oxides. We show the underlying chemical reactions, pH-neutralization processes and phase transformations during this surprisingly simple and fast reduction method. The approach establishes a sustainable toxic-waste treatment from aluminium production through using red mud as feedstock to mitigate greenhouse gas emissions from steelmaking. KW - Multidisciplinary PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594424 DO - https://doi.org/10.1038/s41586-023-06901-z SN - 0028-0836 VL - 625 IS - 7996 SP - 703 EP - 709 PB - Springer Science and Business Media LLC AN - OPUS4-59442 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Adam, Christian T1 - Re-use of secondary phosphates as fertilizers - harmonization of analytical methods N2 - The number of different secondary raw materials used for fertilizer production is expected to increase in the future due to newly developed recycling procedures. Thus, more and more different matrices have to be analyzed. Furthermore, the respective legislation and analytical methodology is nonuniform throughout Europe. Therefore, a harmonization of the the regulations and Standards is desirable. We conduct a research project to test the existing analytical methods on their applicability to a broad variety of matrices to support the harmonization process. The project is scheduled tili late spring 2017. Initial results will be presented. T2 - 15th International waste management and landfill symposium - Sardinia 2015 CY - Cagliari, Italy DA - 06.10.2015 PY - 2015 SN - 9788862650212 PB - CISA Publisher CY - Cagliari AN - OPUS4-34577 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vocks, M. A1 - Adam, Christian A1 - Lesjean, B. A1 - Gnirrs, R. A1 - Kraume, M. T1 - Enhanced post-denitrification without addition of an external carbon source in membrane bioreactors N2 - This study investigates a post-denitrification process without the addition of an external carbon source combined with an enhanced biological phosphorus removal (EBPR) in a membrane bioreactor (MBR). Three trial plants, with two different process configurations, were operated on two different sites, and a variety of accompanying batch tests were conducted. It was shown that even without dosing of an external carbon source, denitrification rates (DNR) much above endogenous rates could be obtained in post-denitrification systems. Furthermore, the anaerobic reactor located ahead of the process had a positive impact on the DNR. Given these surprising results, the project team decided to identify the carbon source used by the microorganisms in the post-denitrification process. Batch tests could demonstrate that lysis products do not play a major role as a C-source for post-denitrification. The following hypothesis was proposed to explain the observations: the glycogen, internally stored by the substrate accumulating bacteria, if anaerobic conditions are followed by aerobic conditions could act as carbon source for denitrification in post-denitrification system. First exploratory batch tests, where the glycogen evolution was monitored, corroborate this assumption. KW - Post-denitrification KW - EBPR KW - Glycogen KW - MBR KW - Metabolism KW - Internal substrate KW - Denitrification rate PY - 2005 DO - https://doi.org/10.1016/j.watres.2005.05.049 SN - 0043-1354 VL - 39 IS - 14 SP - 3360 EP - 3368 PB - Elsevier CY - Amsterdam AN - OPUS4-10760 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Weimann, Karin ED - White, T. ED - Ferraris, C. ED - Yu, L. ED - Halada, K. ED - Umezawa, O. T1 - Recovery of non-renewable resources from waste T2 - 7th International Conference on Ecomaterials (ICEM7); 3rd International Conference on Advanced Materials (ICMAT2005) CY - Singapore DA - 2005-07-03 PY - 2005 SN - 981-05-3611-9 VL - 1 SP - 148 EP - 155 PB - Stallion Press CY - Singapore AN - OPUS4-11831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adamczyk, Burkart A1 - Brenneis, Rudolf A1 - Adam, Christian A1 - Mudersbach, D. T1 - Recovery of chromium from AOD-converter slags N2 - Slags from the production of high-alloyed steel contain both chemically bound chromium (mainly as Cr2O3) in the mineral fraction and elemental chromium in the metallic remainders. Thermochemical post treatment of the slag in an electric arc furnace under reducing conditions enables the nearly complete recovery of the total amount of chromium in form of a metallic alloy. The best results were achieved by resistance melting (submerged electrodes) with addition of a reducing agent into the melt. The efficiencies of the reducing agents carbon, aluminium, silicon (as ferrosilicon) and silicon carbide were investigated and compared. As aluminium is the strongest reducing agent, it is less selective and reduces much more SiO2 than Cr2O3. While SiC shows only low reactivity because of its high thermal resistance, carbon and silicon had the highest reducing potentials: More than 97% of the chemically bound chromium can be recovered by application of these reducing agents. Due to the high temperature required for the reduction of the chromium compounds, the reduction of SiO2 as an undesired side reaction cannot be avoided. However, compared with mechanical procedures that are limited to the recovery of the metallic remainders, the total chromium recovery can be significantly increased by the described reductive melting procedure. KW - Arc furnace KW - By-product KW - Chromium recovery KW - High-alloyed steel KW - Reductive melting KW - Slag treatment KW - Slag KW - Thermochemical treatment PY - 2010 DO - https://doi.org/10.1002/srin.201000193 SN - 1611-3683 SN - 0177-4832 VL - 81 IS - 12 SP - 1078 EP - 1083 PB - Verl. Stahleisen CY - Düsseldorf AN - OPUS4-22898 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Case study 2 - Recovery of phosphorus from sewage sludge ashes T2 - Resources that don't cost the earth Workshop CY - Berlin, Germany DA - 2011-12-01 KW - Resources KW - Phosphorus recovery PY - 2011 SP - 17 AN - OPUS4-26930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Determination of Chemical State of Chromium in Sewage Sludge Ash based Fertilisers T2 - Synchrotron User Meeting 2012 CY - Clayton, Australia DA - 2012-11-29 PY - 2012 AN - OPUS4-27214 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Entsorgung von Rückständen aus der Klärschlammverbrennung T2 - Deutsch-ungarischer Workshop anlässlich der Umweltmesse ÖKOTECH CY - Budapest, Hungary DA - 2008-10-15 PY - 2008 AN - OPUS4-17944 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Grabner, Angela A1 - Adam, Christian T1 - Complete survey of German sewage sludge ash N2 - The amount of sewage sludge produced worldwide is expected to further increase due to rising efforts in wastewater treatment. There is a growing concern against its direct use as fertilizer due to contamination of the sludge with heavy metals and organic pollutants. Incinerating the sludge degrades organic compounds almost completely and concentrates heavy metals and phosphorus. However, the sewage sludge ash (SSA) is almost completely disposed of and with it all resources are removed from the economic cycle. Comprehensive knowledge of the composition of SSA is crucial to assess the resource recovery potentials. We conducted a survey of all SSA emerging in Germany and determined the respective mass fractions of 57 elements over a period of one year. The median content of phosphorus was 7.9%, indicating an important recovery potential. Important trace elements were Zn (2.5 g/kg), Mn (1.3 g/kg), and Cu (0.9 g/kg). Mass fractions of technology metals such as V, Cr, Ga, Nb, and rare earths were comparatively low. Considering the possible use of SSA as secondary raw material for fertilizer production it should be noted that its Cd and U content (2.7 mg/kg and 4.9 mg/kg respectively) is significantly lower than that of rock phosphate based mineral fertilizers. PY - 2014 DO - https://doi.org/10.1021/es502766x SN - 0013-936X SN - 1520-5851 VL - 48 IS - 20 SP - 11811 EP - 11818 PB - ACS Publ. CY - Washington, DC AN - OPUS4-32646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphate fertilizer from sewage sludge and meat and bone meal by thermochemical treatment with Cldonors T2 - 3rd Sustainable Phosphorus Summit CY - Sydney, Australia DA - 2012-02-29 PY - 2012 AN - OPUS4-25581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus flows in German sewage sludge ashes and potential recovery technologies T2 - Mining the Technosphere CY - Wien, Austria DA - 2015-10-01 PY - 2015 AN - OPUS4-34473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Simon, Franz-Georg ED - Martin Faulstich, ED - Peter Quicker, T1 - Ascheentsorgung - Acker oder Deponie? T2 - 4. Fachtagung "Verfahren & Werkstoffe für die Energietechnik - Biomasse & Abfall - Regionale Brennstoffe richtig nutzen" CY - Sulzbach-Rosenberg DA - 2008-06-11 PY - 2008 SN - 978-3-9810391-3-9 N1 - Serientitel: Verfahren & Werkstoffe für die Energietechnik – Series title: Verfahren & Werkstoffe für die Energietechnik IS - 4 SP - 227 EP - 243 PB - DORNER PrintConcept GmbH + Co. KG CY - Sulzbach-Rosenberg AN - OPUS4-17609 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart T1 - Möglichkeiten der thermochemischen Behandlung von Reststoffen KW - Thermochemische Stofftrennung KW - Wertstoffrückgewinnung PY - 2010 DO - https://doi.org/10.1002/cite.201050012 SN - 0009-286X SN - 1522-2640 VL - 82 IS - 9 SP - 1579 EP - 1580 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-22004 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes A1 - Krüger, Oliver ED - Schuhmann, R. T1 - Technische Prozesse zur Phosphorrückgewinnung aus Klärschlammaschen N2 - Klärschlammaschen weisen hohe Gehalte an Phosphor auf, dieser ist allerdings schlecht für Pflanzen verfügbar. Des Weiteren enthalten sie Schwermetalle die vor dem Einsatz als Düngemittel entfernt werden müssen. Vor diesem Hintergrund wurden in den letzten Jahren nasschemische und thermochemische Verfahren entwickelt und zum Teil bereits in Demonstrationsanlagen getestet. Ein thermochemischer Verfahrensansatz wird in diesem Beitrag näher vorgestellt. Klärschlammaschen werden mit Klärschlamm als Reduktionsmittel und Natriumsulfat als Aufschlussmittel im Drehrohrofen thermisch behandelt. Bei diesem Prozess wird pflanzenverfügbares NaCaPÜ4 gebildet, unerwünschte Elemente wie As, Cd, Hg und Pb werden zum Teil über die Gasphase separiert. Die Ergebnisse eines Demonstrationsversuchs werden vorgestellt. N2 - Sewage sludge ashes exhibit high phosphorus mass fractions. However, the availability of phosphorus to plants is poor. Furthermore, sewage sludge ashes contain eco-toxicologically relevant heavy metals that have to be removed prior to agricultural application. ln front of this background several wet-chemical and thermo-chemical processes were developed in the last years and some of them were already successfully demonstrated in large scale. A thermo-chemical approach is presented in this article. Sewage sludge ashes are mixed with dry sewage sludge as reductant and sodium sulfate. Düring thermal treatment in a rotary kiln at approx. 950°C plant available NaCaPCU is formed. Furthermore undesired elements such as As, Cd, Hg and Pb are separated via the gas phase. Results of demonstration trials are presented. T2 - 8. CMM-Tagung 2015 - Innovative Feuchtemessung in Forschung und Praxis - Material - Prozesse - Systeme CY - Karlsruhe, Germany DA - 07.10.2015 KW - Klärschlammasche KW - Phoshorrückgewinnung PY - 2015 N1 - Serientitel: Innovative Feuchtemessung in Forschung und Praxis – Series title: Innovative Feuchtemessung in Forschung und Praxis SP - 251 EP - 262 AN - OPUS4-34859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian A1 - Schulz, T. A1 - Linsz, E. T1 - Environmental evaluation of different ways to produce recycled concrete aggregates N2 - Due to the great quantities of construction and demolition waste in Europe, the reuse of building material waste as secondary raw materials is of particular importance. A recycling of building materials can meet the requirements of sustainability in several aspects: the extended time availability of primary raw materials and the related protection of natural resources as well as the saving of landfill sites. In recent years sulphates originating from gypsum in secondary building materials, made of construction and demolition waste, received growing attention. Sulphates are unwanted in secondary building materials for concrete production as well as for other use e.g. in unbounded layers. The content of gypsum resp. sulphates in secondary aggregates can be reduced by different methods. Depending on the type of material different steps for selective dismantling can be used to separate gypsum containing residues from concrete rubble. Furthermore some steps for the processing of building rubble are suitable for the reduction of sulphates in the produced aggregates. An environmental evaluation of different ways for the production of recycled concrete aggregates was performed with regard to a reduction of sulphates in the secondary building material. The use of techniques for selective dismantling was environmentally advantegous for the deconstruction of three investigated model houses. T2 - SUM2014 - 2nd Symposium on urban mining CY - Bergamo, Italy DA - 19.05.2014 KW - Recycling KW - Concrete aggregates KW - Building waste KW - Construction PY - 2014 SN - 9788862650311 SP - Session C 6, 1 EP - 8 AN - OPUS4-30825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Das Potential Deutscher Klärschlammaschen für die Wertstoffrückgewinnung T2 - VDI Fachkonferenz Klärschlammbehandlung CY - Berlin, Germany DA - 2012-09-26 PY - 2012 AN - OPUS4-26589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg T1 - Recycling of waste materials by thermochemical treatment T2 - ISWA World congress 2010 - Urban development and sustainbility - a major challenge for waste management in the 21st century CY - Hamburg, Germany DA - 2010-11-15 KW - thermochemical substance separation KW - Thermodynamics KW - Thermochemistry PY - 2010 SP - 1 EP - 10(?) AN - OPUS4-22467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian T1 - Ökobilanzielle Bewertungen von Abbruch- und Aufbereitungsverfahren als Grundlage für ein optimiertes Bauschuttrecycling N2 - Prinzipien der Nachhaltigkeit spielen sowohl in Deutschland als auch weltweit zunehmend eine wichtige Rolle. Neben dem Bestreben nach einer Reduzierung des Energieverbrauchs gehört in diesem Zusammenhang auch die Weiterverwendung bzw, Verwertung von Reststoffen und Abfallen zu den wichtigsten Themenbereichen. Baurestmassen sind dabei aufgrund der großen Massenströme von besonderer Bedeutung. T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 12.09.2012 KW - Bauschuttaufbereitung KW - Abbruch KW - Ökobilanzielle Bewertung KW - RC-Beton KW - Gips PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-1042 EP - 2-1049 AN - OPUS4-26606 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Eine nachhaltige Strategie zur Nutzung des Phosphors im Klärschlamm - Ergebnisse aus dem EU-Projekt SUSAN T2 - Internationales Klärschlamm-Symposium, Wege einer verantwortungsvollen Klärschlammentsorgung CY - Fürstenfeldbruck, Germany DA - 2008-06-30 PY - 2008 AN - OPUS4-17695 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gentzmann, Marie A1 - Paul, Andrea A1 - Serrano, Juan A1 - Adam, Christian T1 - Understanding scandium leaching from bauxite residues of different geological backgrounds using statistical design of experiments N2 - The leaching behavior of scandium (Sc) from bauxite residues can differ significantly when residues of different geological backgrounds are compared. The mineralogy of the source rock and the physicochemical environment during bauxitization affect the association of Sc in the bauxite i.e., how Sc is distributed amongst different mineral phases and whether it is incorporated in and/or adsorbed onto those phases. The Sc association in the bauxite is in turn crucial for the resulting Sc association in the bauxite residue. In this study systematic leaching experiments were performed on three different bauxite residues using a statistical design of experiments approach. The three bauxite residues compared originated from processing of lateritic and karstic bauxites from Germany, Hungary, and Russia. The recovery of Sc and Fe was determined by ICP-OES measurements. Mineralogical changes were analyzed by X-ray-diffraction and subsequent Rietveld refinement. The effects of various parameters including temperature, acid type, acid concentration, liquid-to-solid ratio and residence time were studied. A response surface model was calculated for the selected case of citric acid leaching of Hungarian bauxite residue. The investigations showed that the type of bauxite residue has a strong influence. The easily leachable fraction of Sc can vary considerably between the types, reaching ~20–25% in German Bauxite residue and ~50% in Russian bauxite residue. Mineralogical investigations revealed that a major part of this fraction was released from secondary phases such as cancrinite and katoite formed during Bayer processing of the bauxite. The effect of temperature on Sc and Fe recovery is strong especially when citric acid is used. Based on the exponential relationship between temperature and Fe-recovery it was found to be particularly important for the selectivity of Sc over Fe. Optimization of the model for a maximum Sc recovery combined with a minimum Fe recovery yielded results of ~28% Sc recovery at <2% Fe recovery at a temperature of 60 ◦C, a citric acid normality of 1.8, and a liquid-to-solid ratio of 16 ml/g. Our study has shown that detailed knowledge about the Sc association and distribution in bauxite and bauxite residue is key to an efficient and selective leaching of Sc from bauxite residues. KW - Bauxite residue KW - Scandium KW - Leaching KW - Design of experiments KW - Red mud PY - 2022 DO - https://doi.org/10.1016/j.gexplo.2022.107041 SN - 0375-6742 VL - 2022 IS - 240 SP - 1 EP - 13 PB - Elsevier Science CY - Amsterdam AN - OPUS4-55531 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement durch thermochemische Behandlung von mineralischen Nebenprodukten und Abfällen N2 - Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Sekundärrohstoff PY - 2022 SN - 978-3-944310-58-9 SP - 372 EP - 385 PB - TK-Verlag CY - Neuruppin AN - OPUS4-54737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Smol, M. A1 - Adam, Christian A1 - Kugler, Stefan T1 - Thermochemical Treatment of Sewage Sludge Ash (SSA)—Potential and Perspective in Poland N2 - Phosphorus (P) recovery from sewage sludge ash (SSA) is one of the most promising approaches of phosphate rock substitution in mineral fertilizers and might be a sustainable way to secure supply of this raw material in the future. In the current investigation, the process of thermochemical treatment of SSA was applied to SSA coming from selected mono-incineration plants of municipal sewage sludge in Poland (Cracow, Gdansk, Gdynia, Lodz, Kielce and Szczecin). The Polish SSA was thermochemically converted in the presence of sodium (Na) additives and a reducing agent (dried sewage sludge) to obtain secondary raw materials for the production of marketable P fertilizers. The process had a positive impact on the bioavailability of phosphorus and reduced the content of heavy metals in the obtained products. The P solubility in neutral Ammonium citrate, an indicator of its bioavailability, was significantly raised from 19.7–45.7% in the raw ashes and 76.5–100% in the thermochemically treated SSA. The content of nutrients in the recyclates was in the range of 15.7–19.2% P2O5, 10.8–14.2% CaO, 3.5–5.4% Na2O, 2.6–3.6% MgO and 0.9–1.3% K2O. The produced fertilizer raw materials meet the Polish norms for trace elements covered by the legislation: the content of lead was in the range 10.2–73.1 mg/kg, arsenic 4.8–22.7 mg/kg, Cadmium 0.9–2.8 mg/kg and mercury <0.05 mg/kg. Thus, these products could be potentially directly used for fertilizer production. This work also includes an analysis of the possibilities of using ashes for fertilizer purposes in Poland, based on the assumptions indicated in the adopted strategic and planning documents regarding waste management and fertilizer production. KW - Sewage Sludge Ashes KW - Critical raw materials KW - Phosphorus KW - Fertilizer KW - Sewage Sludge PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514468 DO - https://doi.org/10.3390/en13205461 VL - 13 IS - 20 SP - 5461 AN - OPUS4-51446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herzel, Hannes A1 - Stemann, J. A1 - Simon, Sebastian A1 - Adam, Christian T1 - Comparison of thermochemical treatment of sewage sludge ash with sodium sulphate in laboratory-scale and pilot-scale experiments N2 - There is an ongoing debate on European scale concerning the criticality of phosphorus. In Switzerland and Germany, phosphorus recovery from phosphorus-rich waste streams will become obligatory. Sewage sludge ash is rich in phosphorus and may become an important secondary feedstock. Thermochemical treatment of sewage sludge ash with sodium sulphate under reducing conditions was shown to remove heavy metals from the solid product and produce the fully plant available crystalline phase CaNaPO4. Pilot-scale experiments in a rotary kiln were carried out at temperatures between 750 and 1000 °C and were compared to laboratory-scale experiments with crucibles. Process upscaling was successfully demonstrated but a series of differences were noticed: In comparison to laboratory-scale, solubility of phosphorus in samples from pilot-scale experiments was lower at all chosen treatment temperatures because of shorter retention time and incomplete decomposition of sodium sulphate. X-ray diffraction analysis revealed remaining phase fractions of whitlockite (Ca3-x(Mg,Fe)x(PO4)2) and sodium sulphate from the starting materials in products and thus indicated incomplete reaction. In contrast to the results of laboratory-scale experiments, the crystalline phase CaNaPO4 was clearly absent in the products from the rotary kiln but instead a Mg-bearing phase (Ca,Mg)NaPO4 was formed. Laboratory-scale experiments confirmed (Ca,Mg)NaPO4 is an intermediate phase between whitlockite and CaNaPO4. However, both crystalline phases are characterized by high plant availability. It was shown that heavy metal removal increased at higher temperatures whereas solubility and thus plant availability of phosphorus already reached its maxima at temperatures of 950 °C in pilot-scale and 875 °C in laboratory-scale experiments. KW - Crystalline phase identification KW - Heavy metal removal KW - Phosphorus availability KW - Process upscaling KW - Recovery KW - Rhenanite PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-524084 DO - https://doi.org/10.1007/s13762-021-03252-y VL - 19 IS - 3 SP - 1997 EP - 2006 PB - Springer AN - OPUS4-52408 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weimann, Karin A1 - Adam, Christian A1 - Buchert, M. A1 - Sutter, J. T1 - Environmental Evaluation of Gypsum Plasterboard Recycling N2 - Gypsum is widely used in the construction sector and its worldwide consumption has been increasing for several decades. Depending on the life-time of the used gypsum products, an increase of gypsum in construction and demolition waste follows. Especially against the background of a circular economy, the recycling of waste gypsum is of growing importance. However, the use of recycled gypsum makes only sense if it is environmentally friendly. Therefore, an evaluation of the environmental impacts of an industrial-scale processing for the recycling of post-consumer gypsum waste was conducted. The evaluation was performed with an established life cycle assessment software. Original data provided by industry and complementary data from a database for life cycle assessments were used for the calculations. Two scenarios for recycled gypsum with different transportation distances were calculated. These results are compared with results of the environmental evaluation of gypsum derived from coal-fired power plants (FGD gypsum) and natural gypsum. The results show that utilization of recycled gypsum can be environmentally advantageous compared to the use of natural gypsum or FGD gypsum, especially in the impact categories land transformation and resource consumption (abiotic depletion potential). For most environmental impact categories the specific transportation distances have a strong influence. KW - Gypsum plasterboards KW - Gypsum waste KW - Recycled gypsum KW - Environmental evaluation PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522321 DO - https://doi.org/10.3390/min11020101 SN - 2075-163X VL - 11 IS - 2 SP - 101 PB - MDPI CY - Basel, Schweiz AN - OPUS4-52232 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herzel, Hannes A1 - Aydin, Zeynep A1 - Adam, Christian T1 - Crystalline phase analysis and phosphorus availability after thermochemical treatment of sewage sludge ash with sodium and potassium sulfates for fertilizer production N2 - Phosphorus rich sewage sludge ash is a promising source to produce phosphorus recycling fertilizer. However, the low plant availability of phosphorus in these ashes makes a treatment necessary. A thermochemical treatment (800–1000 °C) with alkali additives transforms poorly plant available phosphorus phases to highly plant available calcium alkali Phosphates (Ca,Mg)(Na,K)PO4. In this study, we investigate the use of K2SO4 as additive to produce a phosphorus potassium fertilizer in laboratory-scale experiments (crucible). Pure K2SO4 is not suitable as high reaction temperatures are required due to the high melting point of K2SO4. To overcome this barrier, we carried out series of experiments with mixtures of K2SO4 and Na2SO4 resulting in a lower economically feasible reaction temperature (900–1000 °C). In this way, the produced phosphorus potassium fertilizers (8.4 wt.% K, 7.6 wt.% P) was highly plant available for phosphorus indicated by complete extractable phosphorus in neutral ammonium citrate solution. The added potassium is, in contrast to sodium, preferably incorporated into silicates instead of phosphorus phases. Thus, the highly extractable phase (Ca,Mg)(Na,K)PO4 in the thermochemical products contain less potassium than expected. This preferred incorporation is confirmed by a pilot-scale trial (rotary kiln) and thermodynamic calculation. KW - Phosphorus recovery KW - Recycling fertilizer KW - Calcium alkali phosphate KW - Silicate PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-536276 DO - https://doi.org/10.1007/s10163-021-01288-3 SN - 1611-8227 IS - 23 SP - 2242 EP - 2254 PB - Springer AN - OPUS4-53627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raniro, H.R. A1 - Soares, T.de M. A1 - Adam, Christian A1 - Pavinato, P.S. T1 - Waste-derived fertilizers can increase phosphorus uptake by sugarcane and availability in a tropical soil N2 - The use of highly water-soluble phosphorus (P) fertilizers can lead to P fixation in the soil, reducing fertilization efficiency. Waste-derived, low water-solubility sources can potentially increase sugarcane’s P uptake compared to triple superphosphate by reducing adsorption to the soil. Aims:We aimed to test struvite, hazenite, and AshDec® for their agronomic potential as recycled fertilizers for sugarcane production in a typical tropical soil.We hypothesize that these sources can reduce P fixation in the soil, increasing its availability and sugarcane’s absorption. Methods: In a greenhouse pot experiment, two consecutive sugarcane cycles, 90 days each, were conducted in a Ferralsol. The recovered sources struvite, hazenite, AshDec®, and the conventional triple superphosphate were mixed in the soil in three P doses (30, 60, and 90 mg kg–1), aside a control (nil-P). At both harvests, sugarcane number of sprouts, plant height, stem diameter, dry mass yield, shoot phosphorus, and soil P fractionation were investigated. Results: At 90 days, struvite and hazenite performed better for dry mass yield (70.7 and 68.3 g pot–1, respectively) than AshDec® and triple superphosphate (59.8 and 57.4 g pot–1, respectively) and for shoot P, with 98.1, 91.6, 75.6, and 66.3 mg pot–1, respectively. At 180 days, struvite outperformed all treatments for dry mass yield (95.3 g pot–1) and AshDec® (75.5 mg pot–1) for shoot P. Struvite was 38% and hazenite 21% more efficient than triple superphosphate in P uptake, while AshDec® was 6% less efficient. Soil had higher labile P under struvite, hazenite, and AshDec® than triple superphosphate by the end of the first cycle, while only the later increased nonlabile P by the end of the experiment (180 days). Conclusions:Waste-derived P sources were more efficient in supplying P for sugarcane and delivering labile P in 180 days than triple superphosphate. KW - AshDec KW - Hazenite KW - P-efficiency KW - Recycled sources KW - Struvite PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-544216 DO - https://doi.org/10.1002/jpln.202100410 SN - 1436-8730 SP - 1 EP - 12 PB - Wiley-VCH GmbH AN - OPUS4-54421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schraut, Katharina A1 - Kargl, F. A1 - Adam, Christian A1 - Ivashko, O. T1 - In situ synchrotron XRD measurements during solidification of a melt in the CaO–SiO2 system using an aerodynamic levitation system N2 - Phase formation and evolution was investigated in the CaO–SiO2 system in the range of 70–80 mol% CaO. The samples were container-less processed in an aerodynamic levitation system and crystallization was followed in situ by synchrotron x-ray diffraction at the beamline P21.1 at the German electron synchrotron (DESY). Modification changes of di- and tricalcium silicate were observed and occurred at lower temperatures than under equilibrium conditions. Despite deep sample undercooling, no metastable phase formation was observed within the measurement timescale of 1 s. For the given cooling rates ranging from 300 K s−1 to about 1 K s−1, no decomposition of tricalcium silicate was observed. No differences in phase evolution were observed between reducing and oxidizing conditions imposed by the levitation gas (Ar and Ar + O2). We demonstrate that this setup has great potential to follow crystallization in refractory oxide liquids in situ. For sub-second primary phase formation faster detection and for polymorph detection adjustments in resolution have to be implemented. KW - Aerodynamic levitation KW - Calcium silicate KW - Phase formation KW - Oxide melts KW - In situ synchrotron x-ray diffraction PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526952 DO - https://doi.org/10.1088/1361-648X/abf7e1 VL - 33 IS - 26 SP - 264003 (12pp) PB - IOP Publishing AN - OPUS4-52695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sichler, Theresa Constanze A1 - Adam, Christian A1 - Barjenbruch, M. A1 - Montag, D. A1 - Mauch, Tatjana A1 - Sommerfeld, Thomas A1 - Ehm, J.H. T1 - Variation of the element composition of municipal sewage sludges in the context of new regulations on phosphorus recovery in Germany N2 - Phosphorus (P) recovery is obligatory for all sewage sludges with more than 20 g P/kg dry matter (DM) from 2029 in Germany. Nine wastewater treatment plants (WWTPs) were chosen to investigate variations of phosphorus contents and other parameters in sewage sludge over the year. Monthly sewage sludge samples from each WWTP were analyzed for phosphorus and other matrix elements (C, N, H, Ca, Fe, Al, etc.), for several trace elements (As, Cr, Mo, Ni, Pb, Sn) and loss of ignition. Among the nine WWTPs, there are four which have phosphorus contents both above and below the recovery limit of 20 g/kg DM along the year. Considering the average phosphorus content over the year, only one of them is below the limit. Compared to other matrix elements and parameters, phosphorus fuctuations are low with an average of 7% over all nine WWTPs. In total, only hydrogen and carbon are more constant in the sludge. In several WWTPs with chemical phosphorus elimination, phosphorus fuctuations showed similar courses like iron and/or aluminum. WWTPs with chamber flter presses rather showed dilution efects of calcium dosage. As result of this study, monthly phosphorus measurement is highly recommended to determine whether a WWTP is below the 20 g/kg DM limit. KW - Sewage sludge KW - Phosphorus recovery KW - Wastewater KW - Phosphorus elimination PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557499 DO - https://doi.org/10.1186/s12302-022-00658-4 SN - 2190-4707 VL - 34 IS - 1 SP - 1 EP - 12 PB - Springer Nature CY - Berlin AN - OPUS4-55749 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sichler, Theresa Constanze A1 - Adam, Christian A1 - Becker, Roland A1 - Sauer, Andreas A1 - Ostermann, Markus A1 - Barjenbruch, M. T1 - Phosphorus determination in sewage sludge: comparison of different aqua regia digestion methods and ICP-OES, ICP-MS and photometric determination N2 - Phosphorus recycling from sewage sludge will be obligatory in Germany from 2029. Phosphorus content determination in sewage sludge is crucial to assess the prescribed recycling rates. Currently, German law regards sample preparation using aqua regia digestion in a microwave or under reflux conditions as well as instrumental phosphorus determination by ICP-OES, ICP-MS, or photometric determination with ammonium molybdate as equivalent. However, it is questionable whether these methods are indeed equivalent regarding phosphorus quantification in sludges near the limit of 20 g/kg for mandatory recycling. To answer this question, 15 sewage sludges of 11 different wastewater treatment plants were investigated with all permitted method (digestion and measurement) combinations. Moreover, one sewage sludge was also examined in an interlaboratory comparison (ILC) with 28 participants. This study shows that the above-mentioned methods differ in some cases significantly but across all method combinations and sludges, phosphorus recovery was between 80 and 121% after normalization to the grand mean (average of 15 sludges between 85 and 111%). The ILC and the examination of 15 sludges produced largely similar results. There is a tendency to higher phosphorus recovery after microwave digestion compared to reflux digestion and ICP-OES measurements determine higher phosphorus contents than ICP-MS and photometric phosphorus determination. As a result, the authors recommend ICP-OES determination of phosphorus in sewage sludge after microwave digestion. KW - Sewage sludge KW - ICP-OES KW - Phosphous recovery KW - ICP-MS KW - Photometric P determination KW - Interlaboratory comparison PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-558869 DO - https://doi.org/10.1186/s12302-022-00677-1 VL - 34 IS - 99 SP - 1 EP - 14 PB - Springer AN - OPUS4-55886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dombinov, V. A1 - Herzel, Hannes A1 - Meiller, M. A1 - Müller, F. A1 - Willbold, S. A1 - Zang, J. W. A1 - da Fonseca-Zang, W. A. A1 - Adam, Christian A1 - Klose, H. A1 - Poorter, H. A1 - Jablonowski, N. D. A1 - Schrey, S. D. T1 - Sugarcane bagasse ash as fertilizer for soybeans: Effects of added residues on ash composition, mineralogy, phosphorus extractability and plant availability N2 - Sugarcane bagasse is commonly combusted to generate energy. Unfortunately, recycling strategies rarely consider the resulting ash as a potential fertilizer. To evaluate this recycling strategy for a sustainable circular economy, we characterized bagasse ash as a fertilizer and measured the effects of co-gasification and co-combustion of bagasse with either chicken manure or sewage sludge: on the phosphorus (P) mass fraction, P-extractability, and mineral P phases. Furthermore, we investigated the ashes as fertilizer for soybeans under greenhouse conditions. All methods in combination are reliable indicators helping to assess and predict P availability from ashes to soybeans. The fertilizer efficiency of pure bagasse ash increased with the ash amount supplied to the substrate. Nevertheless, it was not as effective as fertilization with triple-superphosphate and K2SO4, which we attributed to lower P availability. Co-gasification and co-combustion increased the P mass fraction in all bagasse-based ashes, but its extractability and availability to soybeans increased only when co-processed with chicken manure, because it enabled the formation of readily available Ca-alkali phosphates. Therefore, we recommend co-combusting biomass with alkali-rich residues to increase the availability of P from the ash to plants. KW - Combustion and gasification KW - Phosphate extractability and availability KW - X-ray diffraction (XRD) PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567632 DO - https://doi.org/10.3389/fpls.2022.1041924 SN - 1664-462X VL - 13 SP - 1 EP - 13 PB - Frontiers Media CY - Lausanne AN - OPUS4-56763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J. A1 - Barjenbruch, M. A1 - Pinnekamp, J. ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Auswirkungen der novellierten AbfKlärV auf die Kreislaufführung von Pflanzennährstoffen N2 - Because of the longstanding oversupply of nutrients in Germany, waste and fertilization legislation has been amended in 2017. As the new laws do still not meet the European nitrate ordinance, fertilization laws must be tightened again. In consequence, there is a rising competition for land between sewage sludge and organic fertilizers. Furthermore, the new sewage sludge ordinance (AbfKlärV) contains stricter thresholds and a ban on agricultural sewage sludge utilization for WWTPs > 50,000 p.e. from 2029. WWTPs which do not use their sludge for agriculture have to recover phosphorus from then on. However, sludges with less than 2% P content are not affected by that obligation. Every federal state of Germany must report amounts and quality of agricultural utilized sewage sludge yearly. An evaluation of raw data from 10 federal states shows that nearly 40% of both WWTPs and sewage sludge volume fall below the recovery limit of 2%. On the other hand, this means less than 30% of the P potential. In addition, there is no information whether the sludges fall reliably below the limit as required by the ordinance. This project aims to investigate this reliability by regarding the variations in the P content of sewage sludge. For this reason, samples will be taken monthly at 10 representative WWTPs over a year. Whereas phosphorus will still mostly be subject of recovery other nutrients are not affected by this. As a result, large amounts of N, K, Mg and Ca will be increasingly removed from the cycle. In 2017, WWTPs > 50,000 p.e. accounted for 30-60% of the nutrient potentials. These potentials will probably get lost to a large extent due to the fertilization ban. Many small WWTPs are also currently changing their utilization strategy from agriculture to incineration to ensure a safe disposal in future. Therefore, we can expect that even larger amounts of nutrients apart from phosphorus will be discharged from the circular economy. In comparison to the domestic sales volume of mineral fertilizers these other nutrients do only account for a very small fraction. A recovery could nevertheless replace parts of the mineral fertilizers, thus reducing environmental impacts. Energy consumption for technical nitrogen fixation is high and nutrient cycles are strongly anthropogenic influenced with diverse consequences such as eutrophication, acidification and endangered groundwater resources. Sewage sludge contains several micronutrients next to the macronutrients P, N, K, Mg, Ca and S. Because of lacking information on the actual German need for micronutrients contents and freights cannot evaluated. Moreover, former sewage sludge fertilization was probably not needs-based. It is therefore not possible to estimate a true loss in micronutrients due to the amended sewage sludge ordinance. N2 - Die landwirtschaftliche Klärschlammverwertung ist in der Bundesrepublik Deutschland seit Jahren rückläufig, hatte im Jahr 2017 jedoch noch einen Anteil von rund 18 % [20]. Diese Art der Verwertung wird kontrovers diskutiert, da der Klärschlamm im Rahmen der Abwasserreinigung eine Schadstoffsenke darstellt. In vergangenen Jahrzehnten wurden insbesondere die hohen Gehalte an Schwermetallen im Klärschlamm als kritisch für eine landwirtschaftliche Verwertung eingestuft. Diese Belastung konnte allerdings durch Absenkung der Einträge von Schmermetallen in das Abwasser signifikant gesenkt werden. Neben Schwermetallen kamen jedoch auch organische Schadstoffe wie Pharmazeutika, Kosmetika und Haushaltschemikalien in den Fokus der Diskussion über den Einsatz von Klärschlamm auf Agrarflächen. Heute geraten zunehmend weitere Inhaltsstoffe in den Fokus, deren Auswirkungen noch nicht abschließend geklärt sind, weshalb eine einheitliche Bewertung über Grenzwerte nicht darstellbar ist. Beispiele für diese neuen Stoffgruppen sind Mikroplastik, Nanopartikel, Antibiotikaresistenzen und persistente organische Spurenstoffe. Neben den angesprochenen Risiken gibt es in Deutschland Regionen mit einem stark erhöhten Nährstoffüberschuss. In der Kritik steht vor allem eine nicht ordnungsgemäße Düngung mit Stickstoff, welche mit Nitratauswaschungen in das Grundwasser einhergeht. Um diese Grundwasserbelastung zu verhindern wurde u.a. das Düngerecht erneut verschärft, was die Flächenkonkurrenz zwischen Klärschlamm und Wirtschaftsdünger weiter vergrößern wird. Auf Druck der EU-Kommission stehen zudem weitere Anpassungen im Düngerecht bevor, da die beschlossenen Änderungen aus Kommissionssicht nicht ausreichen, um die Nitratrichtlinie einzuhalten. Vor dem Hintergrund der angeführten Probleme wurde im Koalitionsvertrag der 18. Legislaturperiode (2013) festgeschrieben, „die Klärschlammausbringung zu Düngezwecken [zu] beenden und Phosphor und andere Nährstoffe zurück[zu]gewinnen“ [5]. Die novellierte AbfKlärV beinhaltet allerdings kein grundsätzliches Aufbringungsverbot und eine Rückgewinnungspflicht besteht lediglich für den Nährstoff Phosphor. Es ist davon auszugehen, dass sich die neuen Regelungen im Düngerecht und der Klärschlammverordnung massiv auf die landwirtschaftliche Verwertung von Klärschlamm und damit auf die Kreislaufwirtschaft verschiedener Nährstoffe auswirken werden. Zur Ermittlung dieser Auswirkungen wird seit Oktober 2018 im Auftrag des Umweltbundesamtes das REFOPLAN-Projekt „extraWERT“ (FKZ 3718 26 330 0) von der Bundesanstalt für Materialforschung und -prüfung (BAM) in Kooperation mit dem Institut für Siedlungswasserwirtschaft (ISA) der RWTH Aachen durchgeführt. In diesem Beitrag werden erste Ergebnisse dieses Projekts vorgestellt. T2 - Klärschlammkonferenz CY - Berlin, Germany DA - 04.11.2019 KW - Klärschlammdüngung KW - Landwirtschaft KW - Makronährstoffe PY - 2019 SN - 978-3-944310-49-7 VL - 2 SP - 362 EP - 374 PB - Thomé-Kozmiensky Verlag CY - Neuruppin AN - OPUS4-49603 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Martins, I. M. ED - Ulsen, C. ED - Villagran, Y. T1 - Advantages of recycling gypsum plasterboards N2 - Advantages of recycling gypsum plaster boards During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites. Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted. This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process. T2 - IV International Conference Progress of Recycling in the Built Environment CY - Lisbon, Portugal DA - 11.10.2018 KW - Environmental evaluation KW - Gypsum KW - CDW processing PY - 2018 SN - 978-2-35158-208-4 VL - PRO 124 SP - 243 EP - 250 PB - Rilem publications S.A.R.L. CY - Paris AN - OPUS4-48078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - What is in your opinion the fertiliser of the future? N2 - Conventional fertilisers have their disadvantages as nutrient release is not synchronised with the demand of plants. Several approaches of "next generation fertilisers" are aiming at controlled nutrient release. Recycling fertilisers are often not soluble in water but fully plant available. They are suitable raw materials for the production of new types of controlled release fertilisers. T2 - CLOOP-Workshop "What is in your opinion the fertiliser of the future?" CY - Berlin, Germany DA - 22.10.2019 KW - Controlled release fertilisers KW - Recycling fertilisers PY - 2019 AN - OPUS4-49554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie N2 - Carbonfasern sind äußerst stabil und werden auch in Anlagen zur Verbrennung von Sondermüll kaum zerstört. Beim Handling carbonfaserhaltiger Abfälle können Gesundheitsrisken auftreten (Abgabe von WHO-Fasern). Es werden Methoden der Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie diskutiert. T2 - UBA Fachaustausch: Aufbereitung und Verwertung carbonfaserhaltiger Abfälle CY - Dessau, Germany DA - 19.09.2019 KW - Carbonfasern KW - Pyrometallurgie PY - 2019 AN - OPUS4-49555 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, D. A1 - Kargl, F. A1 - Adam, Christian T1 - Formation and chemical stabilisation of tricalcium-silicate during solidification from the melt of post-treated metallurgical slags N2 - Tricalcium-silicate (C3S) or Alite is the most important mineral in Portland cement. Since pure tricalcium-silicate is only stable above temperatures of 1250 °C, its decomposition has to be prevented technically by fast cooling after the sintering process. At room temperature, the decomposition velocity is very slow so that metastable tricalcium-silicate is obtained. Although the mechanisms of clinker phase formation during burning process of Portland cement in a rotary kiln were solved and improved over the years, in view of possible economic and ecological benefits current projects aim to produce clinker phases from metallurgical slags. Recent studies discovered that the mineral phase which remained after a reducing treatment and separation of formed metallic iron from molten Linz-Donawitz (LD-) slags contained about 60 wt.% Alite despite it was cooled slowly. Because the results could be verified using slags from different origins and varying cooling velocities a chemical stabilisation of the Alite can be assumed. First tests in mortars indicate that workability, hardening and solid state properties are comparable with an ordinary Portland cement. An application of the observed phenomenon in cement production requires enhanced knowledge about formation and stabilisation conditions of Alite during crystallisation from melts in contrast to the sintering reactions in conventional Portland cement production. Therefore, this study focuses on the stabilisation mechanisms of Alite in consolidating melts. Samples from different melting experiments are analysed to determine stabilising factors. T2 - 15th International Congress on the Chemistry of Cement CY - Prag, Czech Republic DA - 16.09.2019 KW - Tricalcium-silicate KW - Portland Cement KW - Alite KW - Steelmaking slag PY - 2019 SP - Paper 492, 1 EP - 10 AN - OPUS4-49050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adam, Christian A1 - Peplinski, Burkhard A1 - Kley, Gerd A1 - Kratz, S. A1 - Schick, J. A1 - Schnug, E. T1 - Phosphorrückgewinnung aus Klärschlammaschen - Ergebnisse aus dem EU-Projekt SUSAN N2 - Phosphor ist ein für alle Lebewesen essenzielles Element und kann in seinen Funktionen z. B. als Bestandteil der DNS und RNS sowie als Schlüsselelement beim Energiestoffwechsel (ADP/ATP) nicht ersetzt werden. Klärschlammaschen sind aufgrund ihrer hohen Gehalte an Phosphor (15–25 % P2O5) geeignete Sekundärrohstoffe für die Herstellung von P-Düngemitteln. Aufgrund der schlechten Pflanzenverfügbarkeit des Phosphors und der Gehalte an umweltrelevanten Schwermetallen sollten diese allerdings nicht direkt in der Landwirtschaft eingesetzt werden. Im Mittelpunkt des EU-Projekts SUSAN steht die Entwicklung und Optimierung einer thermochemischen Behandlung von Klärschlammaschen, mit der die Düngewirkung der Aschen auf das Niveau konventioneller Mineraldünger (Thomaskali und Superphosphat SSP) angehoben wird und die Schwermetallkonzentrationen unter die Grenzwerte nach Düngemittelverordnungen europäischer Länder abgesenkt werden. Die sehr positiven Ergebnisse, die bisher im SUSAN-Projekt erzielt wurden, und die darauf basierenden ökonomischen Betrachtungen legen eine großtechnische Umsetzung des Verfahrens nahe. KW - Klärschlamm KW - Phosphor KW - Ressource KW - Klärschlammasche KW - P-Düngemittel KW - Mineralische Phasen PY - 2008 DO - https://doi.org/10.1007/s00506-008-0152-3 SN - 0945-358X SN - 1613-7566 VL - 60 IS - 3-4 SP - 55 EP - 64 PB - Springer CY - Wien AN - OPUS4-17449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorrückgewinnung aus Klärschlammaschen: Forschungsergebnisse aus Deutschland T2 - Klärschlammbehandlung - heute und morgen CY - Wels, Austria DA - 2007-11-21 PY - 2007 AN - OPUS4-16458 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stemann, Jan A1 - Kabbe, C. A1 - Adam, Christian ED - Thomé-Kozmiensky, K.J. ED - Beckmann, M. T1 - Phosphorrückgewinnung im Rahmen der Klärschlammbehandlung - das EU-Projekt P-REX - N2 - Das Element Phosphor ist für alle Lebewesen essentiell. Es ist insbesondere für den Energiestoffwechsel (ATP, ADP), das Speichern und Auslesen von Erbinformationen (DNA, RNA) sowie den Knochenbau unverzichtbar und kann weder synthetisiert noch substituiert werden. Für die Pflanzen- und Tierproduktion werden aus diesem Grund erhebliche Mengen an Phosphor benötigt. Wird dem Ackerboden durch das Pflanzenwachstum und die anschließende Ernte Phosphor entzogen, so muss dieser; zum Erhalt der Ertragsfähigkeit den landwirtschaftlichen Flächen wieder zugeführt werden. Die weitverbreitete direkte Ausbringung von Klärschlamm wird zunehmend kritisch hinterfragt und ist in vielen EU Ländern deutlich rückläufig bzw. verboten. Neben der Hygieneproblematik sind hier insbesondere erhöhte Schwermetallgehalte sowie organische Schadstoffe als kritisch anzusehen. KW - Klärschlammasche KW - Ressourcen KW - Wertstoffpotential KW - Phosphorrückgewinnung PY - 2014 SN - 978-3-944310-06-0 VL - 11 SP - 749 EP - 763 PB - TK Verlag Karl Thomé-Kozmiensky CY - Neuruppin AN - OPUS4-31143 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Recycling von Photovoltaik-Dünnschichtmodulen mit nassmechanischen Verfahren - Ergebnissen des EU LIFE Projektes RESOLVED T2 - Tagung "Aufbereitung und Recycling" CY - Freiberg, Germany DA - 2005-11-09 PY - 2005 AN - OPUS4-11090 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Jones, Roderick ED - Newlands, Moray D. ED - Halliday, Judith E. ED - Csetenyi, Lszlo J. ED - Zheng, Li ED - McCarthy, Michael J. ED - Dyer, Thomas D. T1 - Sustainability in the production of Recycled Concrete Aggregates N2 - Concrete is one of the most widely used construction materials and, accordingly, the concrete industry is an important stakeholder in the field of sustainable construction. Therefore various approaches have been implemented to increase the sustainability of concrete. Besides reducing CO2-emissions during cement production, increasing the energy efficiency of buildings and extending their life span, the end-of-life performance of concrete is also an essential aspect of sustainability. Reusing concrete as a secondary building material meets the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the protection of natural resources as well as conserving landfill site. Furthermore, the production of recycled concrete aggregates (RCA) is a good example for closed-loop recycling. However, regarding the use of RCA as a substitute for natural aggregates in concrete, attention must be paid to all issues of sustainability: this means that environmental, economic and social aspects have to be considered. Since RCA generally have inferior building material properties, such as higher porosity and lower density, the implementation of closed-loop recycling of concrete only makes sense if the technical quality assurance is secured. This paper focusses on the implementation of techniques for the deconstruction/demolition of buildings and the subsequent treatment of concrete rubble in order to improve the building material properties of RCA with regard to the requirements of sustainability and also technical rules and standards. T2 - The 9th International Concrete Conference CY - Dundee, UK DA - 04.07.2016 KW - RCA (Recycled concrete aggregates) KW - Gypsum KW - Selective dismantling KW - CDW treatment KW - Gips KW - Bauschuttaufbereitung PY - 2016 SN - 978-0-9573263-1-6 SP - 1 EP - 10 PB - University of Dundee – Concrete Technology Unit CY - Dundee, UK AN - OPUS4-38175 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Adam, Christian T1 - Recovery potential of German sewage sludge ash N2 - Incineration of sewage sludge is expected to increase in the future due to growing concerns about the direct use of sludge in agriculture. Sewage sludge is the pollutant sink of wastewater treatment and thus loaded with contaminants that might pose environmental hazards. Incineration degrades organic pollutants efficiently, but since the ash is currently mostly disposed of, all valuable component like phosphorus (P) and technologically relevant metals present in the sewage sludge ash (SSA) are removed from the economic cycle entirely. We conducted a complete survey of SSA from German mono-incineration facilities and determined the theoretical recovery potential of 57 elements. German SSA contains up to 19,000 t/a P which equals approximately 13% of phosphorus applied in the German agriculture in form of phosphate rock based mineral fertilizers. Thus, SSA is an important secondary resource of P. However, its P-solubility in ammonium citrate solution, an indicator for the bioavailability, is only about 26%. Treatment of SSA is recommended to enhance P bioavailability and remove heavy metals before it is applied as fertilizer. The recovery potential for technologically relevant metals is generally low, but some of these elements might be recovered efficiently in the course of P recovery exploiting synergies. KW - Sewage sludge ash KW - Recovery potential KW - Phosphorus KW - Critical raw materials KW - Bioavailability KW - Phosphorus recovery KW - Monitoring PY - 2015 DO - https://doi.org/10.1016/j.wasman.2015.01.025 SN - 0956-053X VL - 45 SP - 400 EP - 406 PB - Pergamon Press CY - New York, NY AN - OPUS4-34157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Recycling of Waste Materials by Thermochemical Treatment T2 - ISWA World Congress 2010 Urban Development and Sustainability - a Major Challenge for Waste Management in the 21st Century CY - Hamburg, Germany DA - 2010-11-15 PY - 2010 AN - OPUS4-22473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Severin, M. A1 - Breuer, J. A1 - Rex, M. A1 - Stemann, Jan A1 - Adam, Christian A1 - Van den Weghe, H. A1 - Kücke, M. T1 - Phosphate fertilizer value of heat treated sewage sludge ash N2 - This study focuses on the question whether heat treated sewage sludge ashes are more favourable as fertilizers than untreated sewage sludge ashes (USSA) and whether their fertilization effects are comparable with commercial triple superphosphate (TSP). In a pot experiment, maize was fertilized either with one of three heat treated and Na-, Ca- and Si-compounds amended sewage sludge ashes (two glown phosphates, steel mill slag + sewage sludge ash) or USSA or TSP as control. Fertilization with USSA did not increase the biomass yield and the P uptake of maize in comparison to the P0 treatment (7.25 resp. 8.35 g dry matter/pot). Fertilization with heat treated sewage sludge ashes and TSP resulted in significantly higher yields and plant P uptakes which are on average eight times higher than treatment with USSA and P0 control. Biomass yields and P uptake of maize after fertilization with heat treated sewage sludge ashes are not significantly different from those after TSP fertilization. The main P compound in USSA is Ca3(PO4)2. By heat treatment and amendment with different sodium, calcium, sulphur and silicon containing additives or steel mill converter slag, Ca3(PO4)2 is converted to Ca- and Na-silico-phosphates, which have a higher water solubility than Ca3(PO4)2. This increased solubility is responsible for the high plant availability of this phosphates. KW - P recycling KW - Sustainability KW - P solubility PY - 2014 UR - http://www.agriculturejournals.cz/publicFiles/138177.pdf SN - 1214-1178 SN - 1805-9368 VL - 60 IS - 12 SP - 555 EP - 561 PB - Inst. CY - Prague AN - OPUS4-32147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery by thermochemical treatment of sewage sludge ash - Results of the European FP6-project SUSAN T2 - 2009 International Conference on Nutrient Recovery from Wastewater Streams CY - Vancouver, Canada DA - 2009-05-10 PY - 2009 AN - OPUS4-19543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Krüger, Oliver T1 - Complete survey of German sewage sludge ashes - phosphorous and technology metal recovery potential N2 - Sewage sludge ashes (SSA) are a possible source for recovery of phosphorous (P) and technology metals. Phosphorous is essential for all animate beings. So far, its sole external source is rock phosphate, which is a finite resource. The EU import dependency on P from regions with high domestic demands or political instabilities is almost complete. Furthermore, rock phosphate often contains high amounts of heavy metals like Cd and U that might lead to health and environmetal hazards. P recovered from SSA might diminish these problems. We analyzed SSA from German mono incineration facilities in terms of their elemental composition and respective recovery potential. More than 97% of the emerging SSA is monitored, enabling the determination of complete mass flows of the ashes and their components. Results indicate a P recovery potential of 19,000 t/a (more than 12% of the annual P demands for fertilizer production). The concentrations of Cd and U in SSA are significantly lower than in rock phosphate and thus might help to reduce possible envrionmental and health hazards. T2 - SUM2014 - 2nd Symposium on urban mining CY - Bergamo, Italy DA - 19.05.2014 KW - Sewage sludge KW - Ashes KW - Phosphorous KW - Metal KW - Recovery PY - 2014 SN - 978-8-86265-031-1 SP - Session B 4, 1 EP - 7 AN - OPUS4-30824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adam, Christian ED - H.J. Linke, T1 - Phosphorrückgewinnung aus Abwasser, Klärschlamm und Klärschlammasche T2 - 1. Darmstädter Ingenieurkongress - Bau und Umwelt CY - Darmstadt, Deutschland DA - 2009-09-14 PY - 2009 SN - 978-3-941799-00-4 SP - 62 EP - 66 CY - Darmstadt AN - OPUS4-19896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Adam, Christian A1 - Kley, Gerd T1 - Thermochemische Behandlung von unterschiedlichen Klärschlammaschen mit dem Ziel der Abtrennung von Schwermetallen - Herstellung von Phosphat-Düngemitteln aus den behandelten Aschen: Umweltforschungsplan des Bundesministeriums für Umelt, Naturschutz und Reaktorsicherheit; Abfallwirtschaft; UFOPLAN-Nr. 20333396 N2 - Aufgrund der Endlichkeit der Phosphorlagerstätten und der zu erwartenden Preissteigerungen auf dem Weltmarkt werden Rückgewinnung, Kreislaufflührung und sparsamer Umgang mit dem essentiellen Makronährstoff Phosphor zunehmend interessant. Der P-Rückgewinnung aus biogenen Abfallstoffen wird hierbei zukünftig eine bedeutende Rolle zukommen. Die Aufarbeitung von Klärschlammaschen zu P-Düngemitteln kann in diesem Zusammenhang einen entscheidenden Beitrag leisten. Im Rahmen der vorliegenden Arbeit wurden statische und dynamische Versuche zur thermochemischen Behandlung von Klärschlammaschen mit dem Ziel der Bereitstellung eines geeigneten Sekundärrohstoffes für die P-Düngemittelproduktion durchgeführt. Statische Versuche mit Edelsole (MgCl2Lösung) als Cl-Donator zeigten dass eine weitgehende Schwermetallabreicherung unter signifikanter Steigerung der P-Pflanzenverfügbarkeit möglich ist. Die Schwermetalle wurden in die entsprechenden Chloride überrührt und konnten aufgrund ihrer hohen Dampfdrücke bei Betriebstemperaturen von etwa 1000°C über die Gasphase von der Asche separiert werden. Arsen, Chrom und Nickel konnten mit dieser Behandlungsmethode jedoch nicht entfernt werden. Des weiteren wurde mit der Behandlung nicht für alle untersuchten Klärschlammaschen der Grenzwert der aktuellen Düngemittelverordnung für Kupfer unterschritten. Verbesserungen in Hinblick auf die Reinigungsleistung und die technische Umsetzbarkeit des Verfahrens ließen sich durch Versuche mit Chlorgas als CL-Donator erzielen. Alle Schwermetalle inklusive Arsen, Chrom und Nickel konnten bereits ab einer Betriebstemperatur von 850°C deutlich unter die Grenzwerte nach Düngemittelverordnung abgereichert werden. Die Pflanzenverfügbarkeit des Phosphors war vergleichbar mit den Produkten aus der Behandlung mit Edelsole. Die Citratlöslichkeit konnte von etwa 50-70% (Rohasche) auf 100% (mit Cl2-Gas behandelt) angehoben werden. Bei der kleintechnischen Umsetzung des Verfahrens im Drehrohrofen traten jedoch erhebliche Korrosionsprobleme m Verbindung mit den verwendeten Stahlwerkstoffen auf. Hier besteht Entwicklungsbedarf. Im Rahmen der Untersuchungen wurde gezeigt, dass die vorgeschlagene thermochemische Behandlung von Klarschlammaschen zur Bereitstellung eines Ausgangsmaterials für die P-Düngemittelherstellung geeignet ist und somit ein erhebliches Potential zur nachhaltigen Kreislaufführung der endlichen Ressource Phosphor erschlossen werden kann. Das thermochemische Verfahren führt sowohl zur weitgehenden Entfernung der Schwermetalle als auch zu einer deutlichen Verbesserung der Pflanzenverfügbarkeit des Phosphors. Diese erfolgversprechenden Ergebnisse sollten durch weitere kleintechnische Untersuchungen ergänzt werden, um die Basis für eine großtechnische Anwendung zu schaffen. PY - 2004 SP - 1 EP - 63 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-7304 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Adam, Christian A1 - Kley, Gerd A1 - Simon, Franz-Georg ED - Wang, B. ED - J.H. Song, ED - H. Abe, T1 - Thermal treatment of municipal sewage sludge aiming at marketable P-fertilisers T2 - 8th International Conference on Eco-materials (ICEM8 2007) CY - London, UK DA - 2007-07-09 KW - Sewage sludge KW - Mono-incineration KW - Ash treatment KW - Thermo-chemical treatment KW - P-fertiliser PY - 2007 SN - 978-1-902316-54-3 VL - 2 SP - 435 EP - 442 PB - Brunel University Press CY - London, UK AN - OPUS4-16470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Metal recovery by reductive melting of red mud T2 - Exchange of good practices on metal by-products recovery CY - Brüssel, Belgium DA - 2015-11-12 PY - 2015 AN - OPUS4-34931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Möglichkeiten zur umweltverträglichen Nutzung von Nährstoffen im Klärschlamm T2 - Umwelttechnisch Integrierten Lehrveranstaltung (UTIL), TU CY - Berlin, Germany DA - 2006-06-07 PY - 2006 AN - OPUS4-12432 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorrückgewinnung im Rahmen der Klärschlammbehandlung - das EU-Projekt P-REX T2 - Berliner Abfallwirtschafts- und Energiekonferenz CY - Berlin, Germany DA - 2014-01-27 PY - 2014 AN - OPUS4-31102 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Mory, D. A1 - Schilller, D. A1 - Adam, Christian T1 - Chemische Onlineanalyse von Schmelzen im Lichtbogenofen durch LIBS N2 - Die Reduktion von Metalloxiden zum Metall in einer schmelzflüssigen mineralischen Matrix stellt die Grundlage vieler metallurgischer Verfahren dar. Eine Prozessoptimierung und -kontrolle setzt allerdings die genaue Kenntnis der chemischen Zusammensetzung der Schmelze voraus. Im Beitrag wird LIBS als Methode zur Online-Analyse von Hochtemperaturschmelzen vorgestellt. T2 - Schlacken Symposium 2016 CY - Meitingen, Germany DA - 13.10.2016 KW - Online-Analyse KW - LIBS KW - Lichtbogenofen KW - Prozessoptimierung PY - 2016 SP - 49 EP - 58 AN - OPUS4-38155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -