TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Experimentelle Untersuchung der Massenabbrandraten multipler n-Heptan und Di-tert-butylperoxid Poolfeuer N2 - Es werden Experimente zur Bestimmung der Massenabbrandraten von multiplen Poolfeuern präsentiert. Als Modellsubstanzen dienen n-Heptan und Di-tert-butylperoxid (DTBP). Es werden Versuche im Labormaßstab mit Durchmessern von d = 6 cm und relativen Abständen von 0.08 ≤ D/d ≤ 4 beschrieben und durch Feldversuche mit Pooldurchmessern d = 1.5 m und relativen Abständen zwischen den Pool von 0.17 ≤ D/d ≤ 1 ergänzt. Es kann gezeigt werden, dass die Massenabbrandraten multipler Feuer im Vergleich zu Einzelfeuern mit gleicher Brennstoffoberfläche bis zu einem Faktor 5.9 (n-Heptan) und 1.6 (DTBP) erhöht sind. Die Erhöhung ist abhängig vom relativen Abstand zwischen den Pools D, der Anzahl der Pools N und vom jeweiligen Brennstoff und zeigt ein lokales Maximum, welches mit dem Merging-Bereich der Flammenverschmelzung zusammenfällt. Die Massenabbrandrate als Funktion des relativen Abstandes zwischen den Pools kann durch eine Vergrößerung der Flammenbodenoberfläche infolge Flammenverschmelzung erklärt werden. T2 - 3. Magdeburger Brand- und Explosionsschutztag / vfdb-Workshop CY - Magdeburg, Germany DA - 22.03.2013 KW - Multiple Poolfeuer KW - Massenabbrandraten KW - n-Heptan KW - DTBP PY - 2013 SN - 978-3-00-041601-9 SP - 1 EP - 11 AN - OPUS4-27982 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Malow, Marcus A1 - Berger, Anka A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Mass burning rate of a large TBPB pool fire - experimental study and modeling N2 - Data and prediction for the mass burning rate of a tert-butyl-peroxy-benzoat (TBPB) pool fire (pool diameter = 3 m) is presented. The mass burning rates of TBPB fires are up to six times higher and less dependent on pool diameter compared to hydrocarbon pool fires caused by an additional heat release rate due to exothermic decomposition reaction in the liquid phase. This heat release rate is calculated using a 1st order reaction kinetic obtained from micro calorimetric measurements. A new model is derived considering the heat release rate due to the decomposition reaction which is shown to be 100 % of the heat release rate radiated to the pool surface. With the presented model, including also physical quantities, especially the limiting fuel concentration for upward flame propagation, it is possible to predict the mass burning rates of large TBPB pool fires. The predicted values are in very good agreement with the experiments. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Mass burning rate KW - TBPB (tert-butyl-peroxy benzoat) KW - Pool fire KW - Experimental study KW - Modeling PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331143 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 31 SP - 853 EP - 858 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Limiting distances for flame merging of multiple n-heptane and di-tert-butyl peroxide pool fires N2 - Experiments to determine the limiting distances for flame merging of multiple pool fires are presented. As model substances n-heptane and di-tert-butyl peroxide are used. Laboratory scale tests with a Diameter d = 6 cm and relative distances between the pools of 0.08 ≤ D/d ≤ 4 are described and complemented with field experiments with a diameter d = 1.5 m and relative distances between the pools of 0.17 ≤ D/d ≤ 1. Three regions for flame merging are observed and limiting distances are determined. A merging Region with the limiting distance Dmerg/d within which all flames merge together over the complete burning time. A transition region with the limiting distance Dtran/d within which some flames merge together while other flames are separated from each other. A separated region within which all flames are completely separated from each other. A correlation against the number of burning pools is presented to predict the limiting distances Dmerg/d und Dtran/d. T2 - ICheaP-11 - 11th International conference on chemical & process engineering CY - Milan, Italy DA - 02.06.2013 KW - Multiple fires KW - Flame merging KW - Mass burning rate KW - Limiting distances KW - Pool fire KW - Experimental study KW - Di-tert-butyl peroxide PY - 2013 SN - 978-88-95608-23-5 DO - https://doi.org/10.3303/CET1332021 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 32 SP - 121 EP - 126 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milan AN - OPUS4-28646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vela-Wallenschus, Iris A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Kritische thermische Abstände bei wechselwirkenden KW- und Peroxid-Poolfeuern N2 - In verfahrenstechnischen Anlagen kann es während des Umgangs, des Transports und der Lagerung durch Freisetzung und anschliesender Zündung von brennbaren Flüssigkeiten zu Lachen-, Pool- oder Tankfeuern kommen. Die sich ausbildenden Feuer konnen große Schäden an benachbarten verfahrenstechnischen Anlagen und Personen verursachen. Im Unterschied zu Einzelfeuern sind multiple Pool- und Tankfeuer aufgrund ihrer Wechselwirkungseffekte sicherheitstechnisch von besonderer Bedeutung. Mit Di-tert-butyl-peroxid (DTBP) und n-Heptan als Leitsubstanzen werden Labor- und Feldexperimente (d ≤ 1.5 m) mit wechselwirkenden Poolflammen (N ≤ 9) in einer Matrixanordnung bei relativen horizontalen Abständen D/d zwischen den Pools im Bereich 0.16 ≤ D/d ≤ 4 durchgeführt. Die Phänomene der Flammenverschmelzung (Flammenfusion) in Abhängigkeit vom Poolabstand D/d werden experimentell untersucht und modelliert. T2 - 11. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 07.11.2013 KW - Wechselwirkende Poolfeuer KW - KW-Poolfeuer KW - Peroxid-Poolfeuer KW - Sicherheitsabstände KW - Spezifische Ausstrahlung KW - Bestrahlungsstärke PY - 2013 SN - 978-3-86011-058-4 N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. IS - P-06 SP - 1 EP - 17 AN - OPUS4-29549 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Ziemann, Sylvia A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. ED - Beyer, M. ED - Stolz, T. T1 - Massenabbrandraten organischer Peroxide unter besonderer Berücksichtigung der thermischen Stabilität N2 - Die Flüssigkeitstemperatur Temperatur in der flüssigen Phase unmittelbar im Grenzbereich zur Gasphase während eines Abbrandes organischer Peroxide überschreitet die Onset-Temperatur der beginnenden exothermen Zersetzungsreaktion des Peroxids, so dass diese zu berücksichtigen ist. Für die Peroxide Di-tert-butyl-Peroxid (DTBP) und tert-butyl-peroxybenzoat (TBPB) muss daher bei der Berechnung des Wärmerückstromes ein zusätzlicher Term für die Zersetzung in der Flüssigkeit additiv ergänzt werden. Der Umsatz der Zersetzungsreaktion wird unter den Bedingungen eines CSTR modelliert und erfolgt auf Basis einer Reaktionskinetik 1. Ordnung. Es kann gezeigt werden, dass der Wärmestrom in einem DTBP-Poolfeuer ≈ 40 % und einem TBPB-Poolfeuer ≈ 100 % des Wärmerückstromes durch Wärmestrahlung entspricht. Durch Q-Punkt-d können die vergleichsweise hohen Massenabbrandraten und die relative Unabhängigkeit der Massenabbrandraten vom Pooldurchmesser erklärt werden. Über eine Energiebilanz wird ein Modell basierend auf physikalischen Parametern entwickelt, das die Massenabbrandraten großer Poolfeuer, in sehr guter Übereinstimmung mit den experimentellen Ergebnissen, vorhersagt. T2 - 13. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Braunschweig, Germany DA - 18.06.2013 KW - Poolfeuer KW - Massenabbrandrate KW - Organische Peroxide KW - Thermische Stabilität KW - Onset-Temperatur PY - 2013 SN - 978-3-95606-062-5 DO - https://doi.org/10.7795/210.20130801E SN - 1868-5838 SP - 40 EP - 47 AN - OPUS4-29815 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, A. A1 - Ullner, Christian T1 - Erfolgreicher Abschluss der Normungsarbeit "Instrumentierte Eindringprüfung" - ISO 14577 ist veröffentlicht N2 - Im Oktober 2002 fand die Normungsarbeit zur „Instrumentierten Eindringprüfung“ mit der Veröffentlichung von ISO 14577 mit den drei Teilen: - Teil 1: Prüfverfahren - Teil 2: Prüfung und Kalibrierung der Prüfmaschinen - Teil 3: Kalibrierung von Referenzproben ihren erfolgreichen Abschluss. KW - Härteprüfung KW - Eindringtechnik KW - Mechanische Eigenschaften KW - Schichtprüfung KW - Prüfmaschine PY - 2002 SN - 0011-4952 VL - 81 IS - 10 SP - 684 EP - 689 PB - Beuth-Vertrieb CY - Berlin AN - OPUS4-1739 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ullner, Christian A1 - Wehrstedt, A. T1 - Martenshärte, Eindringhärte oder Eindringmodul ermitteln - Instrumentierte Eindringprüfung nach ISO/DIS 14577 PY - 2001 SN - 0017-6583 SN - 0341-101X VL - 56 IS - 4 SP - 242 EP - 248 PB - Hanser CY - München AN - OPUS4-1747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. ED - Rademaeker, E. D. T1 - Flame heights of di-tert-butyl peroxide pool fires - experimental study and modelling N2 - The flame heights of di-tert-butyl peroxide (DTBP) pool fires with diameters between 0.03 m < d < 3 m are determined by means of visible images obtained by a VHS video recorder. The time-averaged Hav and maximum flame height Hmax were evaluated according to the intermittency criterion. For the relative time-averaged flame heights values in a range of 3.1 < Hav/d < 14.8 are obtained while the relative maximum flame heights are in a range of 3.5 < Hmax/d < 17.6. The experimental measurements were used to establish a new Froude number correlation. T2 - CISAP5 - 5th International Conference on Safety and Environment in Process and Power Industry CY - Milan, Italy DA - 03.06.2012 KW - Pool fire KW - Di-tert-butyl peroxide KW - Flame height KW - Froude number correlation PY - 2012 SN - 978-88-95608-17-4 DO - https://doi.org/10.3303/CET1226061 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 26 SP - 363 EP - 368 PB - Assoziatione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-26012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Schönbucher, A. A1 - Schälike, Stefan A1 - Vela-Wallenschus, Iris A1 - Wehrstedt, Klaus-Dieter ED - Schmidt, J. T1 - CFD simulation of large hydrocarbon and peroxide pool fires N2 - Accidental fires in process Industries often occur as pool fires, which are hazardous to people and adjacent objects because of thermal radiation, largely sooting plumes and formation of other combustion products [1-3]. In addition to experimental pool fire tests, numerical investigation of these fires using Computational Fluid Dynamics (CFD) codes is becoming more important. In regard to safety, thermal radiation is one ofthe main interests in pool fire research. The Surface Emissive Power (SEP) is a key parameter to characterize thermal radiation emitted by a fire. The derived quantity SEP is usually defined as the heat flux due to thermal radiation in relation to flame surface AF. As well as the SEP, the temperatures Tandirradiances E of pool fires are ofparticular interest. CFD Simulation oflarge pool fires is helpful for abetter understanding of fire dynamics and to reduce the number oflarge-scale experiments. To predict the thermal radiation from the jet engine fuel JP-4 (d = 2, 8,16 and 25 m) and DTBP (di-tert-butyl peroxide, d= 1.12 and 3.4m) pool fires CFD methods are used, and the CFD results are compared with experiments. KW - Pool fire KW - JP 4 KW - Organic peroxide KW - DTBP KW - CFD KW - Surface emissive power KW - Irradiation KW - Safety distances PY - 2012 SN - 978-3-527-33027-0 N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. IS - Chapter 9 SP - 139 EP - 157 PB - Wiley-VCH Verlag GmbH & Co. KGaA AN - OPUS4-25897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Gawlowski, M. A1 - Schönbucher, A. T1 - Validation of submodels for CFD simulation of n-hexane pool flames including interferometry N2 - Computational fluid dynamics (CFD) simulation is used to predict transient and time-averaged glame temperatures and species concentrations of an n-hexane pool flame. Employing a combination of an assumed probability density function approach with laminar flamelets using detailed kinetic data and large-eddy simulation with Smagorinsky submodel is shown to be a promising way in modeling pool and tank fires. The measured species concentration and flame temperature profiles from gas chromatography, thermocouple measurements and holographic interferometry are used to validate the submodels for CFD simulation of pool flames. KW - Computational fluid dynamics (CFD) KW - Interferometry KW - Large eddy simulation (LES) KW - Non-premixed flame KW - Pool fire PY - 2012 DO - https://doi.org/10.1002/cite.201100179 SN - 0009-286X SN - 1522-2640 VL - 84 IS - 4 SP - 484 EP - 490 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25418 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Taming the silicon tetraazide beast N2 - Highly energetic silicon tetraazide 1 is synthesized safely in high yield and high purity. The compound is prepared as a solution in benzene which allows it to be handled safely. Stable Lewis base adducts of Si(N3)4 (e.g. 2) are also prepared by treatment of either Si(N3)4 or the di­sodium salt of hexaazidosilicate (3) with Lewis bases (2,2-bipyridine or 1,10-phenanthroline). Unlike Si(N3)4 the Lewis base adduct 2 is thermally stable and does not decompose below 265 °C. The decomposition is very energetic (ΔHd = -2.4 kJg-1) which means 2 and related Lewis base ­adducts could replace environmentally harmful Pb(N3)4 used as primary explosive. KW - Highly energetic silicon tetraazide KW - Lewis base adducts KW - Azides KW - Silicon KW - Energetic materials PY - 2011 DO - https://doi.org/10.1055/s-0030-1259150 SN - 1861-1958 VL - 1 SP - 0043 EP - 0043 PB - Thieme CY - Stuttgart AN - OPUS4-32352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Filippou, A.C. A1 - Portius, P. A1 - Neumann, D.U. A1 - Wehrstedt, Klaus-Dieter T1 - The hexaazidogermanate(IV) ion: syntheses, structures, and reactions KW - Azides KW - Density functional calculations KW - Germanium KW - Hypervalent compounds KW - Main group elements PY - 2000 DO - https://doi.org/10.1002/1521-3773(20001201)39:23<4333::AID-ANIE4333>3.0.CO;2-S SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 39 IS - 23 SP - 4333 EP - 4336 PB - Wiley-VCH CY - Weinheim AN - OPUS4-22203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Neutrale Lewis-Basen-Addukte des Siliciumtetraazids KW - Azide KW - Hyperkoordination KW - N-Liganden KW - Silicium KW - Stickstoffreiche Verbindungen PY - 2010 DO - https://doi.org/10.1002/ange.201001826 SN - 0044-8249 SN - 0932-2140 SN - 1521-3757 VL - 122 IS - 43 SP - 8185 EP - 8189 PB - Wiley-VCH CY - Weinheim AN - OPUS4-22201 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Neutral lewis base adducts of silicon tetraazide KW - Silicon KW - Azides KW - Hypercoordination KW - Nitrogen-rich compounds KW - N-ligands PY - 2010 DO - https://doi.org/10.1002/anie.201001826 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 49 IS - 43 SP - 8013 EP - 8016 PB - Wiley-VCH CY - Weinheim AN - OPUS4-22202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, Klaus-Dieter A1 - Filippou, A.C. A1 - Portius, P. A1 - Neumann, D.U. T1 - Das Hexaazidogermanat(IV)-Ion - Synthesen, Strukturen und Reaktionen PY - 2000 DO - https://doi.org/10.1002/1521-3757(20001201)112:23<4524::AID-ANGE4524>3.0.CO;2-S SN - 0044-8249 SN - 0932-2140 SN - 1521-3757 VL - 112 IS - 23 SP - 4524 EP - 4527 PB - Wiley-VCH CY - Weinheim AN - OPUS4-1060 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -