TY - JOUR A1 - Rhiem, S. A1 - Barthel, Anne-Kathrin A1 - Meyer-Plath, A. A1 - Hennig, M. P. A1 - Wachtendorf, Volker A1 - Sturm, Heinz A1 - Schäffer, A. A1 - Maes, H. M. T1 - Release of 14C-labelled carbon nanotubes from polycarbonate composites JF - Environmental Pollution N2 - Waste disposal of carbon nanotube (CNT) containing products is expected to be the most important pathway for release of CNTs into the environment. In the present work, the use of radiolabelled CNTs (14C-CNT) for polycarbonate polymer nanocomposites with 1 wt% 14C-CNT content allowed for the first time to quantify and differentiate the CNT release according to the type of impact along the materials' ageing history. After an initial exposure of the nanocomposite by solar-like irradiation, further environmental impacts were applied to composite material. They aimed at mimicking disposal site conditions that may induce further ageing effects and CNT release. This study included shaking in water, rapid temperature changes, soaking in humic acid solution as well as waste water effluent, and, finally, gentle mechanical abrasion. All ageing impacts were applied sequentially, both on pristine (control) and on solar-irradiated nanocomposites. All experiments were accompanied by absolute quantification of radioactive release as well as chemical and morphological analyses of the nanocomposite surfaces using infra-red (IR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The morphological analysis showed that spectral irradiation can uncover CNT networks on the outer nanocomposite surface layers by polymer degradation. After having subjected the solar-irradiated nanocomposite to all studied disposal site effect, the total radioactive release was quantified to amount to 64 mg CNT/m2, whereas only 0.8 mg CNT/m2 were found for the un-irradiated control sample. Solar degradation of polymers was thus found to significantly increase the propensity of the studied polymer nanocomposites to release CNTs during ageing effects at the product's end-of-life typical for disposal sites. KW - Weathering KW - Carbon nanotubes KW - Nanocomposites KW - Release KW - Quantification PY - 2016 UR - http://www.sciencedirect.com/science/article/pii/S0269749116303748 DO - https://doi.org/10.1016/j.envpol.2016.04.098 SN - 0269-7491 VL - 215 IS - August SP - 356 EP - 365 PB - Elsevier Ltd. CY - Paris AN - OPUS4-36899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, K. A1 - Meyer-Plath, Asmus A1 - Keller, D. A1 - Ohl, A. T1 - On the Applicability of Plasma Assisted Chemical Micropatterning to Different Polymeric Biomaterials JF - Plasmas and polymers N2 - A plasma process sequence has been developed to prepare chemical micropatterns on polymeric biomaterial surfaces. These patterns induce a guided localized cell layover at microscopic dimension. Two subsequent plasma steps are applied. In the first functionalization step a microwave ammonia plasma introduces amino groups to obtain areas for very good cell adhesion; the second passivation step combines pattern generation and creation of cell repelling areas. This downstream microwave hydrogen plasma process removes functional groups and changes the linkages of polymer chains at the outermost surfaces. Similar results have been obtained on different polymers including polystyrene (PS), polyhydroxyethylmethacrylate (PHEMA), polyetheretherketone (PEEK), polyethyleneterephthalate (PET) and polyethylenenaphthalate (PEN). Such a rather universal chemical structuring process could widen the availability of biomaterials with specific surface preparations. KW - Microwave plasma KW - Ammonia KW - Hydrogen KW - Polymer surface KW - Cell culture KW - XPS KW - Fluorescence PY - 2002 DO - https://doi.org/10.1023/A:1016239302194 SN - 1084-0184 SN - 1572-8978 VL - 7 IS - 2 SP - 103 EP - 125 PB - Plenum Press CY - New York, NY AN - OPUS4-1729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meyer-Plath, Asmus A1 - Finke, B. A1 - Schröder, K. A1 - Ohl, A. T1 - Pulsed and cw microwave plasma excitation for surface functionalization in nitrogen-containing gases JF - Surface and coatings technology N2 - Results are presented of polymer surface functionalization processes in pulsed and continuous wave (cw) microwave-excited plasmas in nitrogen-containing gases under admixture of hydrogen. A maximum selectivity of 100% for amino groups with respect to all nitrogen functional groups (NH2/N) was obtained in cw microwave (MW) plasmas either for very short treatment durations below 100 µs in pure NH3, or within approximately 10 s in hydrogen-rich nitrogen-containing plasmas. The amino and overall nitrogen surface densities, NH2/C and N/C, reach up to 3.5% and 35%, respectively. Post plasma processes of functionalized polymers are discussed in the light of monofunctionalization. Down to pulse duration of 1 ms, plasma decomposition rates of NH3, determined by infrared absorption spectroscopy, are found to scale linearly with the duty cycle. In this regime, the main effect of a duty cycle variation in pulsed NH3 plasmas on surface functionalization can be interpreted to result from changes in the concentration of the dominant stable species in the gas phase, NH3, N2 and H2, which are activated by subsequent plasma pulses. With increasing duty cycle, NH3 decomposition to N2 and 3H2 more and more dominates over the supply of fresh NH3. The nitrogen-removing role of hydrogen in the plasma is discussed in detail, whereas the role of the numerous transient nitrogen-containing species remains to be studied in the future. KW - Pulsed microwave plasma KW - Amino group KW - Polymer KW - Ammonia KW - Infrared absorption PY - 2003 DO - https://doi.org/10.1016/S0257-8972(03)00563-2 SN - 0257-8972 VL - 174-175 SP - 877 EP - 881 PB - Elsevier Science CY - Lausanne AN - OPUS4-13512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meyer-Plath, Asmus A1 - Schröder, K. A1 - Finke, B. A1 - Ohl, A. T1 - Current trends in biomaterial surface functionalization - nitrogen-containing plasma assisted processes with enhanced selectivity JF - Vacuum N2 - Low-pressure gas-discharge plasmas are widely used for polymer surface functionalization on industrial scale. For biomaterial applications, the density and selectivity of the functionalization are of particular importance, because functional groups control the immobilization of biomolecules. Therefore, surface modification of biomaterials is a challenging task for low-pressure plasma technique. Plasma processes have been successfully applied to various polymer types in order to generate multifunctional surfaces. This paper discusses the present state and the prospects of non-coating plasma processes to generate mono functional surfaces of controlled amino group density. Such surfaces appear most desirable for many applications. The results of various microwave- and radio-frequency- excited plasma processes reported in the literature are reviewed and compared to a sequence of experiments that was conducted in a UHV reaction environment. Non-thermal plasmas are especially well suited for thermally damageable polymers. The effect of hydrogen admixture to discharges in nitrogen and ammonia is discussed in detail. The optimization of process parameters lead to highly selective amino functionalization of high density. The selectivity reached 100% -NH2/N at a surface density of amino groups of 3% -NH2/C. KW - Low pressure plasma KW - Grafting KW - Polymers KW - Amino group KW - Surface analysis PY - 2003 DO - https://doi.org/10.1016/S0042-207X(02)00766-2 SN - 0042-207X VL - 71 IS - 3 SP - 391 EP - 406 PB - Elsevier Science CY - Kidlington AN - OPUS4-13686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zeynalov, Eldar A1 - Friedrich, Jörg Florian A1 - Meyer-Plath, Asmus A1 - Hidde, Gundula A1 - Nuriyev, L. A1 - Aliyeva, A. Z. A1 - Cherepnova, Y. T1 - Plasma-chemically brominated single-walled carbon nanotubes as novel catalysts for oil hydrocarbons aerobic oxidation JF - Applied catalysis / A N2 - Brominated single-walled carbon nanotubes [(Br)n-SWCNT) produced by the plasma-chemical technique were involved in the liquid-phase process of hydrocarbons aerobic oxidation. The significant catalytic effect of the (Br)n-SWCNT was revealed at first by the cumene initiated model oxidation and then in experiments on profound aerobic oxidation of petroleum naphthenic fraction derived from the commercial Azerbaijan (Baku) oils blend diesel cut. The ability of (Br)n-SWCNT to accelerate the aerobic oxidation of the hydrocarbons was found out for the first time. Obviously this phenomenon originates from the peculiarities of electronic configuration of the (Br)n-CNT patterns. The plausible mechanism of (Br)n-SWCNT catalytic action is inclined to the formation of reactive oxygen species. The catalytic activity of (Br)n-SWCNT markedly exceeds the activity of the industrial catalysts, manganese salt of indigenous petroleum acids, used for the liquid phase petroleum hydrocarbons oxidation process. KW - Brominated carbon nanotubes KW - Plasma-chemical technique KW - Model cumene oxidation KW - Oxidation rate KW - Oxidation catalysts KW - Oil hydrocarbons liquid-phase oxidation KW - Manganese naphthenate KW - Synthetic petroleum acids PY - 2013 DO - https://doi.org/10.1016/j.apcata.2013.01.003 SN - 0926-860X SN - 1873-3875 VL - 454 SP - 115 EP - 118 PB - Elsevier CY - Amsterdam AN - OPUS4-28290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fortini, Renata A1 - Meyer-Plath, A. A1 - Kehren, D. A1 - Gernert, U. A1 - Agudo Jácome, Leonardo A1 - Sturm, Heinz T1 - Measurement of flexural rigidity of multi-walled carbon nanotubes by Dynamic Scanning Electron Microscopy JF - Fibers N2 - In this work the flexural rigidity of individual large diameter multi-walled carbon nanotubes (MWCNTs) was investigated. The bending modulus were obtained by detecting the resonance frequencies of mechanically excited cantilevered carbon nanotubes using the so-called dynamic scanning electron microscopy technique, and applying the Euler–Bernoulli beam theory. For the nanotubes studied, we determined a modulus of up to 160 GPa. This agrees with values reported by other authors for MWCNTs produced by catalytic chemical vapor deposition, however, it is 6-8 times smaller than values reported for single and multi-walled carbon nanotubes produced by arc-discharge synthesis. Toxicological studies with carbon nanotubes have been showing that inhaled airborne nanofibers that reach the deep airways of the respiratory system may lead to serious, asbestos-like lung diseases. These studies suggested that their toxicity critically depends on the fiber flexural rigidity, with high rigidity causing cell lesions. To complement the correlation between observed toxicological effects and fiber rigidities, reliable and routinely applicable measurement techniques for the flexural rigidity of nanofibers are required. KW - Flexural rigidity KW - Bending modulus KW - Resonance frequency KW - Carbon nanotubes KW - Fiber toxicology PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514190 DO - https://doi.org/10.3390/fib8050031 SN - 2079-6439 VL - 8 IS - 5 SP - 31 PB - MDPI AN - OPUS4-51419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zeynalov, Eldar A1 - Wagner, M. A1 - Friedrich, Jörg Florian A1 - Magerramova, M. A1 - Salmanova, N. A1 - Hidde, Gundula A1 - Meyer-Plath, A. T1 - The peculiar behavior of functionalized carbon nanotubes in hydrocarbons and polymeric oxidation environments JF - JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY N2 - It has been shown that selected types of substituents are able to vary the oxidative behavior of multi-walled carbon nanotubes. Such substituents investigated were sterically hindered secondary amino groups bonded in grafted piperidine units and covalently bonded bromine groups. Their interference and activity was preliminary determined in the model cumene and then in oil diesel fraction and low density polyethylene oxidation reactions. Results obtained indicate that chemical linking of amine moieties containing –NH groups directly to the carbon nanotubes core significantly increases their intrinsic anti-oxidative capacity while the grafting of Br-groups provokes the opposite functioning of the pristine samples. This inference was proved by thermogravimetric and differential thermal analysis of the polyethylene composites and experiments on profound aerobic oxidation of petroleum naphthenic fraction derived from the commercial Baku oils blend diesel cut. KW - Multi-walled carbon nanotubes KW - Amine derivatives KW - Plasma-chemical technique KW - Brominated carbon nanotubes KW - Rate of model oxidation KW - Anti-oxidative efficiency KW - Catalytic activity KW - Inhibition rate constant KW - Photoelectron spectroscopy KW - Oxidation KW - Polyethylene composites KW - Oil diesel fraction PY - 2016 DO - https://doi.org/10.1080/01694243.2016.1239304 SN - 0169-4243 SN - 1568-5616 VL - 31 IS - 9 SP - 988 EP - 1006 AN - OPUS4-39894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -