TY - JOUR A1 - Medina, A. A1 - Ol, M. V. A1 - Greenblatt, D. A1 - Müller-Vahl, H. A1 - Strangfeld, Christoph T1 - High-Amplitude Surge of a Pitching Airfoil: Complementary Wind- and Water-Tunnel Measurements N2 - RECENT interest in gust response, rotorcraft forward flight and wind energy, among other applications, has focused on streamwise oscillations of nominally two-dimensional airfoils in attached and separated flows. The airfoil may be simultaneously held at constant incidence or execute some maneuver, such as pitch. The relative freestream is spatially uniform but temporally unsteady, and this can be accomplished in a ground-test facility in two ways. The first method is to vary the output of the prime mover, such as the rotational speed of the impeller or the blower driving a wind tunnel, or (alternatively) to vary the pressure drop in the tunnel, thereby varying the flow speed in the test section, despite nominally constant primemover revolutions per minute. The second method is used to keep the tunnel’s operating speed constant, as well as to move the test article in the streamwise direction, fore and aft (for example, via an electric linear motor), such that the relative freestream speed felt by the test article varies according to some waveform. Typically, the latter approach is chosen in water tunnels, where there is too much tunnel-circuit inertia to vary the flow speed directly but where the usually low tunnel test section flow speeds enable large excursions in the relative freestream by oscillation of the test article. In fact, outright reverse flow is possible by moving the test article in the laboratory frame at a higher speed than the water-tunnel flow speed. In either case, a sinusoidal relative-speed waveform is the most intuitively realizable, and this can be combined with similar oscillations in the airfoil incidence angle or other kinematics. Although the two methods of realizing streamwise oscillations are mechanically distinct, experimental comparisons between an oscillating test article in a water tunnel and a stationary test article in a wind tunnel with a louvermechanismhave demonstrated agreement in themeasured lift and drag histories. Such experimentswere performed by Granlund et al. for a 10% freestream amplitude oscillation and fixed airfoil incidence, comparing a free-surface water tunnel and a closed-circuit wind tunnel. After buoyancy was subtracted from the wind-tunnel data (resulting from the louver pressure drop) and the model inertia subtracted from the water-tunnel data (resulting from acceleration of the test article), the remaining lift and drag histories matched well at the low freestream oscillation amplitude regime. The work of Granlund et al. was later extended to high-advance-ratio streamwise oscillations of 50% amplitude by Greenblatt et al., where the aerodynamic histories of the water-tunnel and wind-tunnel facilities were compared in combined pitch and freestreamoscillations (governed by relative pitch phase), pure pitch oscillations, and purely freestream oscillations. Agreement between the two facilities’ data for fixed-incidence streamwise oscillations was reasonably good, and in fact, better than agreement in just the static lift and drag, evidently owing to differences in blockage and model-support systems. Additionally, Greenblatt et al. determined there was no strong coupling between simultaneous freestream oscillations and pitch oscillations on resultant lift and moment coefficients. KW - Wind energy KW - Dynamic stall KW - Deep stall KW - Airfoil surging KW - Airfoil pitching PY - 2018 DO - https://doi.org/10.2514/1.J056408 SN - 0001-1452 SN - 1533-385X VL - 56 IS - 4 SP - 1703 EP - 1709 PB - American Institute of Aeronautics and Astronautics AN - OPUS4-43994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiedmann, A. A1 - Weise, Frank A1 - Kotan, E. A1 - Müller, H. S. A1 - Meng, Birgit T1 - Effects of fatigue loading and alkali-silica reaction on the mechanical behaviour of pavement concrete N2 - The primary aim of this paper is to analyze the impact of mechanical pre-damage and alkali–silica reaction (ASR) on the fracture mechanical properties of pavement concrete. For this purpose, a four point bending test was applied to large format beams to produce a defined level of cyclic pre-damage. The fatigue-induced concrete degradation process was simultaneously recorded using a testing procedure specifically developed for the purpose. In addition, fatigue-induced cracks on extracted drilling cores were spatially visualized and quantified using micro X-ray 3D-computed tomography (3D-CT). The storage of the small-format test specimens, with and without cyclic pre-damage, in an ASR-conducive environment showed that pre-damage leads to an increase in ASR damage processes. Subsequent structural mechanical investigations on small format specimens with and without pre-damage show that fatigue loading and ASR significantly influence fracture mechanical parameters of the concrete. KW - Acoustic emissions analysis KW - Alkali-silica reaction KW - Concrete pavement KW - Fatigue loading KW - Fracture energy KW - Monitoring of damage KW - Tensile strength KW - Ultrasonic velocity PY - 2017 DO - https://doi.org/10.1002/suco.201600179 SN - 1751-7648 SN - 1464-4177 VL - 18 IS - 4 SP - 539 EP - 549 PB - Ernst & Sohn AN - OPUS4-41007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Garofano, A. A1 - Fontana, Patrick A1 - Müller, U. ED - Lourenco, P.B. ED - Haseltine, B.A. ED - Vasconcelos, G. T1 - Static behaviour of earth block masonry: experimental testing and finite element modelling N2 - In this paper an extensive research campaign aimed to define the mechanical performance of earth block masonry panels is presented. Uniaxial compression and diagonal compression tests were performed. The test results confirmed the brittle behaviour of earth block masonry under uniaxial compressive load and showed that the failure of earth block masonry under shear load occurs by sliding of the earth blocks along the mortar joints after initial cracking in mortar joints and earth blocks. For diagonal compression test results showed that building technique practice is one of the key factors affecting the structural performances. Experimental behaviour was modelled with a non-linear model capable of describing cracking behaviour. Both micro-modelling and macro-modelling implementing isotropic or orthotropic material laws were used to assess the reliability of different modelling strategies. The model calibration was carried out by sensibility analysis of the input parameters to understand the influence of unit strength on the shear behaviour of masonry. T2 - 9th IMC - International Masonry Conference CY - Guimaraes, Portugal DA - 07.07.2014 KW - Earthen materials KW - Compression test KW - Diagonal compression test KW - Numerical modelling KW - Earth block masonry KW - Uniaxial compression test PY - 2014 SN - 978-972-8692-85-8 SP - Paper ID 1484, 1 EP - 14 AN - OPUS4-31138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Miccoli, Lorenzo A1 - Garofano, A. A1 - Fontana, Patrick A1 - Müller, U. ED - Jäger, W. T1 - Modellierung der mechanischen Eigenschaften von Lehmsteinmauerwerk unter statischer Druck- und Schubbeanspruchung N2 - In diesem Beitrag werden numerische Analysen der mechanischen Eigenschaften von Lehmsteinmauerwerk unter Druck- und Schubbeanspruchung vorgestellt. Ergebnisse von einachsigen Druck- und Schubversuchen an Wandprüfkörpern lieferten dafür grundlegende mechanische Kennwerte im elastischen Bereich und im nichtelastischen Versagenszustand.Die Testergebnisse zeigten, dass verschiedene Vorlasten keinen wesentlichen Einfluss auf die Schubfestigkeit haben. Außerdem bestätigten die Ergebnisse das spröde Verhalten von Lehmsteinmauerwerk unter einachsiger Druckbelastung und es zeigte sich, dass das Versagen des Lehmsteinmauerwerks unter Scherbelastung entlang der Mörtelfugen erfolgt. Die experimentellen Ergebnisse wurden verwendet, um das Verhalten von Lehmsteinmauerwerk durch nichtlineare Finite-Elemente-Methoden auf der Basis von Makro- und Mikro-Modellierungsansätzen zu simulieren. Entsprechendes konstitutives Materialverhalten und Zwängungen, die in den Versuchen durch die Art der Lasteinleitung in Form von Stahlprofilen und Stahlschuhen verursacht wurden, wurde in den Modellen berücksichtigt. Es wurde zuerst ein auf der Grundlage der experimentellen Daten kalibriertes Makro-Modell entwickelt, was zu einer brauchbaren Vorhersage des Versagensverhaltens der Mauerwerksprüfkörper führte. Die simulierten Spannungs-Dehnungs-Kurven, berechnet unter einachsiger Druckbelastung, zeigten eine gute Übereinstimmung mit den Ergebnissen der geprüften Mauerwerkskörper, sowohl im elastischen als auch im nichtelastischen Bereich. Ein vereinfachter Ansatz, basierend auf der Makro-Modellierung und einem homogenisierten Prüfkörper, kann für die Untersuchung größerer Tragsysteme oder ganzer Gebäude angewendet werden, wobei eine zufriedenstellende Genauigkeit bei geringerem Rechenaufwand erreicht wird. Obwohl das globale Spannungs-Dehnungs-Verhalten zufriedenstellend wiedergegeben wurde, ist ein solches nichtlineares isotropes Kontinuumsmodell für Lehmsteinmauerwerk nicht in vollem Umfang geeignet, um das bei den Versuchen beobachtete Rissbild an den Prüfkörpern zu simulieren. Eine detailliertere Analyse des mechanischen Verhaltensdes Mauerwerks wurde mit einem Mikro-Modellierungsansatz durchgeführt. Das Modell, in dem ein Wandabschnitt nicht mehr homogenisiert, sondern in konkrete Stein- und Fugenelemente diskretisiert wird, hat sich insbesondere für das Verhalten von Lehmsteinmauerwerk unter Schubbeanspruchung als geeignet erwiesen. Die Auswertung der Spannungsverteilungen bei der nichtlinearen Analyse lieferte Informationen über die tatsächlichen Mechanismen der Lastübertragung zwischen Steinen und Mörtelfugen. Mit dem Mikro-Modell war es möglich, das nichtlineare Verhalten von Lehmsteinmauerwerk vorherzusagen. Es stellt somit ein geeignetes Werkzeug für die Untersuchung der Versagensmechanismen von Lehmsteinmauerwerk dar. Allerdings sind aufgrund der Komplexität des Modells für die Beschreibung der Stein/Mörtel-Schnittstelle und die hohe Anzahl an erforderlichen mechanischen Parametern umfassendere Untersuchungen notwendig. Die zukünftige Forschung wird sich daher einerseits auf die Verfeinerung der numerischen Modelle und andererseits auf die Simulation komplexer Belastungssituationen und Gebäudekomponenten konzentrieren. KW - Lehmsteinmauerwerk KW - Mechanische Eigenschaften KW - Statische Druck- und Schubbeanspruchung KW - Lehmbau KW - Baustoffe PY - 2017 SN - 978-3-433-03161-2 SP - 195 EP - 208 PB - Ernst & Sohn CY - Berlin AN - OPUS4-39631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gianneo, A. A1 - Carboni, M. A1 - Müller, Christina A1 - Ronneteg, U. T1 - PAUT inspection of copper canister: structural attenuation and POD formulation N2 - For inspection of thick-walled (50mm) copper canisters for final disposal of spent nuclear fuel in Sweden, ultrasonic inspection using phased array technique (PAUT) is applied. Because thick-walled copper is not commonly used as a structural material, previous experience on Phased Array Ultrasonic Testing for this type of application is limited. The paper presents the progress in understanding the amplitudes and attenuation changes acting on the Phased Array Ultrasonic Testing inspection of copper canisters. Previous studies showed the existence of a low pass filtering effect and a heterogeneous grain size distribution along the depth, thus affecting both the detectability of defects and their "Probability of Detection" determination. Consequently, the difference between the first and second back wall echoes were not sufficient to determine the local attenuation (within the inspection range), which affects the signal response for each individual defect. Experimental evaluation of structural attenuation was carried out onto step-wedge samples cut from full-size, extruded and pierced&drawn, copper canisters. Effective attenuation values has been implemented in numerical simulations to achieve a Multi Parameter Probability of Detection and to formulate a Model Assisted Probability of Detection through a Monte-Carlo extraction model. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) CY - Minneapolis, MN, USA DA - 26.07.2015 KW - Phased array ultrasonic testing KW - POD KW - Copper PY - 2016 DO - https://doi.org/10.1063/1.4940649 SN - 0094-243X VL - 1706 SP - Article: 200005, 1 EP - 13 PB - AIP Publishing AN - OPUS4-37592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Favre, A. A1 - Hilbert, F. A1 - Quercetti, Thomas A1 - Neumeyer, Tino A1 - Weingart, Barbara T1 - Prototype testing of a protective structural packaging for 30B cylinder N2 - Three drop test campaigns have been performed with DN 30 Protective Structural Packaging (PSP) developed by DAHER NUCLEAR TECHNOLOGIES GmbH for the transport of natural, enriched and reprocessed uranium hexafluoride (up to 5 wt%) in 30B cylinders. The mechanical prototype testing is intended to demonstrate that the package DN30 complies with regulatory requirements under normal and hypothetical accident conditions of transport (NCT, ACT) relevant to IF, AF and B(U)F packages, respectively. The paper includes the results of the latest test campaign carried out in 2015-2016 at the drop test facility of BAM, Germany with new full scale prototypes of the DN30 PSP and 30B cylinders. Repetition of drop test sequences became necessary after changing to Polyisocyanurate foam as shock absorbing material with variable foam densities. Furthermore, the mechanical behavior of the UF6 content of the 30B cylinder is now simulated by a mixture of cement and steel grid as modified surrogate material; instead of small steel balls. The behavior of this new content simulation is assumed to be more realistic with respect to the properties of real UF6. T2 - PATRAM 2016, 18th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Kobe, Japan DA - 18.09.2016 KW - Drop test KW - Packaging KW - Radioactive material KW - Uranium hexafluoride PY - 2016 SP - Paper 1018, 1 EP - 11 PB - INMM CY - Deerfield, Illinois, USA AN - OPUS4-37568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul A1 - Müller, C. A1 - Meyer, A. A1 - Halle, T. ED - Lampke, T. ED - Wagner, G. ED - Wagner, M. F.-X. T1 - Einfluss von Stickstoff auf Mikrostruktur und Korrosionsverhalten martensitischer nichtrostender Stähle N2 - Die Korrosionsbeständigkeit martensitischer nichtrostender Stähle (MNS) wird wesentlich von der chemischen Zusammensetzung und dem Wärmebehandlungszustand beeinflusst. Beides bestimmt die Verteilung der Legierungselemente im Gefüge und die daraus resultierenden Werkstoffeigenschaften. Das Legieren mit Stickstoff bewirkt im Allgemeinen eine Verbesserung der Lochkorrosionsbeständigkeit von nichtrostenden Stählen. Bei martensitischen nichtrostenden Stählen ist dieser Effekt nicht nur auf den Stickstoffgehalt selbst zurückzuführen, sondern auch auf den gleichzeitig verringerten Kohlenstoffgehalt, der ebenfalls das Ergebnis der Wärmebehandlung beeinflusst. In dieser Arbeit wird der Einfluss von Stickstoff auf die Korrosionsbeständigkeit in Bezug zum Härtungsprozess von MNS dargestellt. Dazu wird vergleichend der Effekt von Austenitisierungsdauer, -temperatur und Abkühlgeschwindigkeit auf Gefüge, Härte und Korrosionsbeständigkeit der MNS X50CrMoV15 und X30CrMoN15 1 untersucht. Die Abkühlgeschwindigkeit wurde mit dem Stirnabschreckversuch gezielt variiert, um den Einfluss von Abkühlgeschwindigkeiten von > 100 K/s bis 1 K/s zu charakterisieren. Die Veränderungen der Korrosionsbeständigkeit werden durch die elektrochemisch potentiodynamische Reaktivierung (EPR) und durch die Bestimmung kritischer Lochkorrosionspotentiale dokumentiert. Neben diesem experimentellen Ansatz werden auch die Ergebnisse von thermodynamischen Berechnungen mit der Software Thermocalc vorgestellt und abschließend auch zur Interpretation des Einflusses von Stickstoff auf die Korrosionsbeständigkeit martensitischer nichtrostender Stähle genutzt. T2 - 18. Werkstofftechnisches Kolloquium der TU Chemnitz CY - Chemnitz, Germany DA - 10.03.2016 KW - Korrosionsbeständigkeit KW - Corrosion resistance KW - Wärmebehandlung KW - Heat treatment KW - Nichtrostende Stähle KW - Stainless steels KW - Thermocalc KW - Thermocalc PY - 2016 SN - 978-3-00-052212-3 SN - 1439-1597 VL - 59 SP - 325 EP - 336 PB - TU Chemnitz, Fakultät für Maschinenbau, Institut für Werkstoffwissenschaft und Werkstofftechnik CY - Chemnitz AN - OPUS4-37263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Österle, Werner A1 - Müller, Urs A1 - Desplanques, Y. A1 - Bulthé, A.-L. A1 - Degallaix, G. A1 - Dmitriev, A.I. T1 - 3rd Body formation of two different brake pad materials designed for railway application T2 - 5th European Conference on Braking (JEF 2006) CY - Lille, France DA - 2006-11-08 PY - 2006 SP - 107 EP - 115 AN - OPUS4-18699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krumbholz, N. A1 - Jansen, A. A1 - Scheller, M. A1 - Müller-Wirts, T. A1 - Lübbecke, S. A1 - Holzwarth, R. A1 - Scheunemann, R. A1 - Wilk, R. A1 - Sartorius, B. A1 - Roehle, H. A1 - Stanze, D. A1 - Beckmann, Jörg A1 - von Chrzanowski, Lars A1 - Ewert, Uwe A1 - Koch, M. ED - Keith A. Krapels, ED - Neil A. Salmon, T1 - Handheld terahertz spectrometer for the detection of liquid explosives N2 - We present a handheld fiber-coupled terahertz spectrometer operating at a center wavelength of 1550 nm. The key elements are a fs-fiber laser, a fiber stretcher delay line and fiber-coupled antennas, which contain novel InAlAs-InGaAs multi layer chips. First experimental data obtained with this system demonstrates its great potential and robustness. In addition, we investigate different hazardous and harmless liquids in reflection geometry. These experiments show that liquids are in principle distinguishable by terahertz spectroscopy. Finally, first steps towards an algorithm that allows for an extraction of the liquids dielectric properties are discussed. The algorithm works for the analysis of reflection data even if the liquid is located inside a container. KW - Handheld terahertz spectrometer KW - Liquid explosives PY - 2009 DO - https://doi.org/10.1117/12.830381 SN - 0277-786X VL - 7485 SP - 748504-1 - 748504-12 AN - OPUS4-20268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Esslinger, Susanne A1 - Becker, Roland A1 - Müller-Belecke, A. A1 - Jung, Christian A1 - Nehls, Irene T1 - Bioisomerization of HBCD: Results of feeding experiments with pure Gamma-HBCD enantiomers N2 - 1,2,5,6,9,10-hexabromocyclododecane (HBCD), a widely used flame retardant, is an ubiquitous contaminant in the environment. Still, only little is known about the distribution and behavior in the environment such as bioaccumulation or biotransformation of HBCD stereoisomers. In order to investigate enrichment and possible bioisomerization of HBCD stereoisomers, Mirror Carps were exposed to pure (+)- and (-)-γ-HBCD, randomly sampled after a predefined specific period and subjected to enantiomer-specific determination of α-, β-, and γ- HBCD. No evidence for the isomerization of HBCD stereoisomers was observed in Mirror Carp fillets. T2 - Dioxin 2009 - 29th International symposium on halogenated persistent organic pollutants / Organohalogen compounds CY - Beijing, China DA - 2009-08-23 PY - 2009 UR - http://www.dioxin20xx.org/pdfs/2009/09-103.pdf VL - 71 SP - 000487 EP - 000492 CY - Beijing, China AN - OPUS4-21187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Esslinger, Susanne A1 - Becker, Roland A1 - Müller-Belecke, A. A1 - Bremser, Wolfram A1 - Jung, Christian A1 - Nehls, Irene T1 - HBCD stereoisomer pattern in mirror carps following dietary exposure to pure Gamma-HBCD enantiomers KW - Enantiomer-specific determination KW - HPLC-MS/MS KW - Brominated flame retardant KW - Fish feeding experiment KW - Enantiomer fraction KW - Bioisomerization PY - 2010 DO - https://doi.org/10.1021/jf101469q SN - 0021-8561 SN - 1520-5118 VL - 58 IS - 17 SP - 9705 EP - 9710 PB - American Chemical Society CY - Columbus, Ohio AN - OPUS4-23173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, W.H. A1 - Worrack, H. A1 - Sterthaus, Jens A1 - Villain, J. A1 - Wilden, J. A1 - Juritza, A. T1 - How to extract continuum materials properties for (lead-free) solders from tensile tests and nanoindentation experiments N2 - Fabrication of modern microelectronic components requires miscellaneous solder materials for joining. In order to guarantee the quality of the manufacturing process and the reliability of the resulting solder joint it is necessary to know the material properties of the joining parts and of the solder materials. In particular Young’s modulus, yield stress, and the hardness are of great interest. Moreover, a complete stress-strain curve is important for a detailed material characterization and simulation of a component, e.g., by Finite Elements (FE). The miniaturization of modern electronic products with small solder joints allows only fabrication of very small-sized specimens. Because of this miniature tests are used for measuring the mechanical properties of the solders in the experimental investigations of this paper. More specifically two miniature tests are presented and discussed, a mini-uniaxial-tension-test and a nanoindenter experiment. In the tensile test the axial loading is prescribed, the corresponding extension of the specimen length is recorded, both of which determines the stress-strain- curve directly. The stress-strain curves are then mathematically analyzed by assuming a non-linear relationship between stress and strain of the Ramberg-Osgood type and fitting the corresponding parameters to the experimental data by means of an optimization routine. For a detailed analysis of very local mechanical properties nanoindentation is used, resulting primarily in load vs. indentation-depth data. According to the procedure of Pharr and Oliver this data can be used to obtain hardness and Young’s modulus but not a complete stress-strain curve, at least not directly. In order to obtain such a stress-strain-curve, the nanoindentation experiment is combined with FE and the coefficients involved in the corresponding constitutive equation for stress and strain are obtained by means of the inverse method. Finally in this paper, the stress-strain curves from nanoindentation and tensile tests are compared for two materials, namely aluminum and steel and differences are explained in terms of the locality of the measured properties. KW - Inverse method KW - FEA KW - Stress-strain curves KW - Nanoindentation KW - Tensile tests PY - 2009 DO - https://doi.org/10.1007/s00542-008-0688-y SN - 0946-7076 SN - 1432-1858 VL - 15 IS - 1 SP - 45 EP - 55 PB - Springer CY - Berlin AN - OPUS4-19264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolar, J. A1 - Strlic, M. A1 - Müller-Hess, D. A1 - Gruber, A. A1 - Troschke, K. A1 - Pentzien, Simone A1 - Kautek, Wolfgang T1 - Near-UV and visible pulsed laser interaction with paper N2 - The applicability of excimer laser at 308 nm and Nd:YAG laser at 532 nm with fluences below 0.86 J/cm2 for cleaning of cellulose and paper materials was evaluated. The extent of degradation of purified cotton cellulose and Fabriano paper after laser treatment as well as after a period of accelerated humid oven ageing was determined by following the changes in the degree of polymerization. While irradiation of paper with the excimer laser at 308 nm results in depolymerization of cellulose accompanied by a decrease in ISO brightness, no detrimental effects of Nd:YAG laser treatments were observed. PY - 2000 DO - https://doi.org/10.1016/S1296-2074(00)00149-7 SN - 1296-2074 SN - 1778-3674 VL - 1 IS - sup.1 SP - 221 EP - 224 PB - Elsevier CY - Paris AN - OPUS4-5979 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gaal, Mate A1 - Bär, Sylke A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Bloodworth, T. A1 - Lewis, A. A1 - Guelle, D. ED - Harmon, R. S. T1 - Optimizing detector trials for humanitarian demining T2 - Conference 2004 CY - Orlando, FL, USA DA - 2004-04-12 KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2004 SN - 0-8194-5338-2 DO - https://doi.org/10.1117/12.541124 SN - 1605-7422 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 5415 SP - 1323 EP - 1334 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-6045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Gaal, Mate A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Lewis, A. A1 - Bloodworth, T. A1 - Wilrich, Peter-Th. A1 - Guelle, D. T1 - ITEP project 2.1.1.2 - Final report - Reliability model for test and evaluation of metal detectors N2 - Metal detectors used in demining have been tested within the frame of the International Test and Evaluation Programme project ITEP 2.1.1.2. Detection reliability tests were performed in accordance with the CEN workshop agreement describing specifications for test and evaluation (CWA 14747:2003). Results of these tests are aimed to verify and should help to optimise the proposed testing procedures. KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2004 UR - http://www.itep.ws/pdf/Itep_no2.1.1.2_reliability_model.pdf N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 1 EP - 51 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-6049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Bär, Sylke A1 - Lewis, A. A1 - Bloodworth, T. A1 - Guelle, D. A1 - Wilrich, Peter-Th. T1 - ITEP-Test Trials for Detection Reliability Assessment of Metal Detectors N2 - The total reliability of a mine searching system is driven by the triple of intrinsic capability, which describes the physical-technical basis capability, the application and environmental factors and the human factors. Some of them can be determined in laboratory measurements but the human factor and a part of environment conditions and their interaction with the device need to be treated statistically. That is why the test & evaluation procedure described in CEN CWA 14747:2003, includes in addition to parameter tests of metal detectors also the reliability or blind field tests under local conditions with local personnel. A series of three big field trials had been accomplished in the ITEP-project 2.1.1.2 “Reliability Model for Test & Evaluation of Metal Detectors” to specify the optimum conditions for reliable trial results with affordable effort. For each set of specific working conditions, characterized in terms of a combination of one mine type in one soil with one detector handled by local personnel, the searching system will show up a working performance in mine detection rates as a function of mine depth and show up a certain overall false call rate. During the ITEP-trials in Benkovac and Oberjettenberg the authors learnt to determine this function separately for each mine type in each soil, which is especially important for low metal mines in uncooperative soil which will be illustrated for the mine PMA2 in different types of soil. The question of representativeness for field conditions on the one hand and necessary statistical set up for the possibility to distinguish between individual detector performances is still under discussion. KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2005 UR - http://maic.jmu.edu/journal/8.2/rd/mueller.htm SN - 1533-9440 SN - 1533-6905 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. IS - 8.2 SP - 86 EP - 90 CY - Harrisonburg AN - OPUS4-6041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spickermann, J. A1 - Martin, K. A1 - Räder, H.J. A1 - Müllen, K. A1 - Schlaad, H. A1 - Müller, A. H. E. A1 - Krüger, Ralph-Peter T1 - Quantitative analysis of broad molecular weight distributions obtained by MALDI-TOF mass spectrometry PY - 1996 SN - 1469-0667 SN - 1356-1049 SN - 1365-0718 IS - 2 SP - 161 EP - 165 PB - IM Publications CY - Chichester AN - OPUS4-2153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlaad, H. A1 - Müller, A. H. E. A1 - Kolshorn, H. A1 - Krüger, Ralph-Peter T1 - Mechanism of anionic polymerization of (meth)acrylates in the presence of aluminium alkyls PY - 1995 SN - 0170-0839 SN - 1436-2449 VL - 35 SP - 169 EP - 176 PB - Springer CY - Berlin AN - OPUS4-2144 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Müller, Christina A1 - Osterloh, Kurt A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Guelle, D. A1 - Lewis, A. T1 - Metal Detector Test Trials in Germany and Croatia - ITEP Project 2.1.1.2 T2 - MATEST 2003 NDT Achievements and Challenges CY - Brijuni-Pula, Croatia DA - 2003-09-28 KW - Demining KW - Metal detectors KW - Reliability tests KW - ROC diagrams KW - Test and evaluation KW - CWA07 PY - 2003 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 1(?) EP - 15(?) AN - OPUS4-2784 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlaad, H. A1 - Müller, A. A1 - Spickermann, J. A1 - Räder, H. A1 - Krüger, Ralph-Peter T1 - Quantitative Analysis of Molecular Weight Distribution Obtained by Matrix-Assisted Laser Desorption/Ionization Time-of-Flight Mass Spectrometry (MALDI-TOF-MS) T2 - 2nd International Conference on Molecular Mass Characterization of Synthetic and Natural Polymers CY - Bradford, England, UK DA - 1996-04-01 PY - 1996 CY - Bradford AN - OPUS4-2218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, A. A1 - Krüger, Ralph-Peter T1 - Quantitative analysis of molecular weight distribution obtained by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry T2 - DECHEMA-Diskussionstagung "Neue Methoden der Polymeranalytik" CY - Mainz, Germany DA - 1996-10-07 PY - 1996 CY - Mainz AN - OPUS4-2224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Mielke, Werner A1 - Hampe, Andreas A1 - Lützow, Wolfgang A1 - Müller, Hansjörg A1 - Pastuska, Gerhard A1 - Rook, A. A1 - Schnabel, E. A1 - Sickfeld, Jürgen A1 - Tobisch, Karl A1 - Trubiroha, Peter T1 - Einsatz von Kunststoffen in Pkw - Literaturstudie PY - 1990 SN - 0937-1214 IS - 2 SP - 9 EP - 257 PB - Bundesanstalt für Straßenwesen CY - Bergisch Gladbach AN - OPUS4-11796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Thiel, A. A1 - Eberstein, Markus A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Deubener, J. A1 - Schiller, Wolfgang Arno T1 - Viskosität von sinternden Glas/Kristallphasen-Kompositen T2 - 80. Glastechnische Tagung CY - Dresden, Deutschland DA - 2006-06-12 PY - 2006 SN - 3-921089-46-8 SP - 1(?) EP - 3(?) PB - Verl. d. Dt. Glastechn. Ges. CY - Offenbach AN - OPUS4-14045 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Thiel, A. A1 - Eberstein, Markus A1 - Müller, Ralf A1 - Deubener, J. T1 - Viskosität von Glasmatrix-Kompositen mit partiell löslicher kristalliner Dispersphase T2 - 81. Glastechnische Tagung und 4. DGG-Symposium "Novel Optical Technologies" CY - Aachen, Deutschland DA - 2007-06-04 KW - Glasmatrixkomposite KW - Lösung KW - Sintern PY - 2007 SN - 978-3-921089-52-1 IS - CD-ROM SP - 1 EP - 8 PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-16212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chabrelie, A. A1 - Müller, Urs A1 - Scrivener, K.L. ED - Palomo, Á. ED - Zaragoza, A. ED - Agüí, J. C. L. T1 - Mechanisms of degradation of concrete by external sufate ions under laboratory and field conditions N2 - The durability of concrete is a major challenge for the construction, which devotes one third to one half of its annual investment to building maintenance. The lack of fieid data regarding concrete durability, especially in the case of exposure to Sulfate ions (“sulfate attack”) makes it dijficult to determine the appropriate fest methods andperformance criteria. Additionally, the increased use of sustainable blends (cement with mineral admixtures, typically slag from the iron industiy) suffers from a lack of experience regarding their long-term performance. Most results for sulfate resistance are derived from accelerated laboratoiy tests xvhere performance criteria are based only on macroscopic properties, especially expansion. To fill this gap and better widerstand the mechanisms of sulfate attack under real conditions, a parallel study of laboratoiy micro-concrete and fieid concrete samples under sulfate exposure was undertaken, focussing on microstructural changes in addition to the conventional macroscopic characterisation. Four exposure regimes were designed in the laboratoiy: full immersion (ponding), pH-control, semi-immersion and wet/diy cycles. Pure Portland blends and slag blends witli high level of slag replacement (70 wt.-%) were investigated. The exposure regime has been found to play a major role in the damage process. In ponding conditions, the damage process takes place in three stages characterised by a first period of induction, followed by surface damage thatfinally extends to the bulle of the material. Paradoxically, the w/c-ratio does not seem to have much impact on the ionic transport phenomena but might be more decisive in the microstructure mechanical strength against local stresses. The slag blends, considered as sulfate resistant in ponding exposure, revealed badperformances under wet/diy cycles. This beliaviour was attributed to poor proper physical resistance of the slag hydrates against diying. The fieid concretes selected for the comparison with the laboratoiy cases were partially buried in a sulfate-enriched soil in Argentina. A pure Portland blend and a slag blends with high level of slag replacement (80 wt.-%) were investigated. The submerged part of the samples could be compared to the laboratoiy ponding exposure, wliile the upper layer of the samples subjected to weathering could be compared to the laboratoiy wet/diy cycles exposure. The fieid obsen’ations tend to confirm the laboratoiy results and validate the fest settings. It has been underlined that a direct relationship between damage (e.g.; cracking/expansion) andphase assemblage was not evident. However, the study highlights that sulfate combination with the hydrates of the cement (e.g.; C-S-H) and with those of the slag would play a rote in the initiation of the expansion, which would be attributed to a swelling of the hydrates or to the precipitation offine ettringite after the Saturation level in sulfate of the hydrates has been reached. T2 - 13th International congress on the chemistry of cement - XIII ICCC CY - Madrid, Spain DA - 03.07.2011 KW - Sulfate attack KW - Exposure conditions KW - Concrete KW - Laboratory test KW - Field KW - Phase assemblage KW - Microstructure KW - XRD KW - SEM KW - SCM KW - Slag PY - 2011 SN - 978-84-7292-400-0 SP - 1 EP - 14 CY - Madrid AN - OPUS4-24810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Golze, Manfred A1 - Müller, Andreas A1 - Recknagel, Angelika A1 - Steffen, Bernd A1 - Boley, N. A1 - van der Veen, A. T1 - Interlinkages and recognition of proficiency testing schemes PY - 2000 SN - 0949-1775 SN - 1432-0517 PB - Springer CY - Berlin AN - OPUS4-1063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smith, A. A1 - Müller, Christina A1 - Rosenthal, Martina T1 - Accidents and Incidents in Humanitarian Demining (HD) - the Need to Keep Accurate Records for Meaningful Analysis T2 - European-American Workshop 2002 CY - Berlin, BAM, Germany DA - 2002-09-11 PY - 2002 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. AN - OPUS4-2021 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Thieme-Hack, M. A1 - Berghaus, U. A1 - Brümmer, F. A1 - Elsner, U. A1 - Färber, C. A1 - Frank, D. A1 - Illgas, M. A1 - Kalbe, Ute A1 - Kathage, J. A1 - Leers, A. A1 - Müller, B. A1 - Röger-Göpfert, C. A1 - Russland, H.-J. A1 - Schnabel, B. A1 - Schneider, O. A1 - Schockmann, D. A1 - Schomakers, H. A1 - Schwalbe, D. A1 - Stegemann, D. A1 - van den Berg, T. A1 - Kramps, S. T1 - Fachbericht Kunststoffsportböden - Nachhaltige Kunststoffbelagsauswahl für Sportfreianlagen N2 - Kunststoff- und Kunststoffrasenflächen kommt bei intensiv genutzten Flächen als Allwetterbeläge eine große Bedeutung zu. Sie leisten einen wichtigen Beitrag zur Absicherung eines ganzjähriger Sportangebote. Gerade Kunststoffrasen ist aber in den letzten Jahren häufig in die Kritik geraten, insbesondere durch gefährliche Inhaltsstoffe und andere negative Einflüsse auf die Umwelt. Dies hat bei Bauherren zu einer Verunsicherung geführt und Fragen aufgeworfen, die erst teilweise beantwortet sind. Die Diskussionen rund um diesen Allwetterbelag haben bereits dazu geführt, dass von Seiten der Industrie viel verändert wurde und neue innovative Lösungen gefunden werden. Der Fachbericht stellt eine Handreichung für Fachleute und interessierte Laien dar, um mehr Klarheit besonders hinsichtlich der Umweltanforderungen zu erzielen. KW - Kunststoffsportbeläge KW - Kunstrasen KW - Umweltverträglichkeit KW - Schadstofftransfer KW - Mikroplastik PY - 2022 UR - https://shop.fll.de/de/fachbericht-kunststoffsportboeden-broschuere.html SP - 1 EP - 70 PB - Forschungsgesellschaft Landschaftsentwicklung Landschaftsbau (FLL) CY - Bonn AN - OPUS4-54390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, A. A1 - Müller, Thoralf A1 - Balzer, M. A1 - Fenker, M. A1 - Kappl, H. T1 - Corrosion protection mechanisms of TiMgN hard coatings on steel N2 - . Hard coated steel components are used in a wide application range, mostly for protective, wear resistant and decorative purposes. Despite of these coatings being regarded as relatively dense, there is always a high risk of localized corrosion when a coated low alloyed steel component encounters a surrounding high humidity atmosphere or even an aqueous medium. An approach to enhance the corrosion properties is the addition of magnesium to physical vapor deposited hard coatings, like TiN. It has been found that there is a remarkable increase in corrosion resistance in dependence of magnesium content of the TiMgN coating and its surface properties. In this work the authors will explain the underlying corrosion protection mechanisms by means of electrochemical and analytical studies. The positive impact of magnesium in the coating relates on its preferred dissolution vs. steel. This causes the potential to shift to more negative direction with respect to the steel substrate and additionally leads to a temporarily passivation of the steel due to alkalization of the surrounding electrolyte by formation of magnesium hydroxide. T2 - 20. Werkstofftechnisches Kolloquium CY - Chemnitz, Germany DA - 14.03.2018 KW - Corrosion KW - Titanium nitride KW - PVD hard coating KW - Magnesium PY - 2018 SN - 978-3-00-058901-0 SN - 1439-1597 VL - 72 SP - 74 EP - 83 PB - Eigenverlag CY - Chemnitz AN - OPUS4-44526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kirilina, E. A1 - Helbling, S. A1 - Morawski, M. A1 - Pine, K. A1 - Reimann, K. A1 - Jankuhn, S. A1 - Dinse, J. A1 - Deistung, A. A1 - Reichenbach, J. R. A1 - Trampel, R. A1 - Geyer, S. A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Arendt, T. A1 - Bazin, P.-L. A1 - Weiskopf, N. T1 - Superficial white matter imaging: Contrast mechanisms and whole-brain in vivo mapping N2 - Superficial white matter (SWM) contains the most cortico-cortical white matter connections in the human brain encompassing the short U-shaped association fibers. Despite its importance for brain connectivity, very little is known about SWM in humans, mainly due to the lack of noninvasive imaging methods. Here, we lay the groundwork for systematic in vivo SWM mapping using ultrahigh resolution 7 T magnetic resonance imaging. Using biophysical modeling informed by quantitative ion beam microscopy on postmortem brain tissue, we demonstrate that MR contrast in SWM is driven by iron and can be linked to the microscopic iron distribution. Higher SWM iron concentrations were observed in U-fiber–rich frontal, temporal, and parietal areas, potentially reflecting high fiber density or late myelination in these areas. Our SWM mapping approach provides the foundation for systematic studies of interindividual differences, plasticity, and pathologies of this crucial structure for cortico-cortical connectivity in humans. KW - Magnetic resonance imaging KW - Laser ablation KW - ICP-MS KW - Brain KW - Imaging PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514430 DO - https://doi.org/10.1126/sciadv.aaz9281 SN - 2375-2548 VL - 6 IS - 41 SP - eaaz9281 PB - American Association for the Advancement of Science (Science/AAAS) CY - Washington, DC, USA AN - OPUS4-51443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weise, Frank A1 - Wiedmann, A. A1 - Voland, Katja A1 - Kotan, E. A1 - Ehrig, Karsten A1 - Müller, Harald S. T1 - Auswirkungen von Ermüdungsbeanspruchungen auf Struktur und Eigenschaften von Fahrbahndeckenbeton N2 - Ausgehend von der Zielsetzung der DFG-Forschergruppe 1498, die Einflüsse auf den AKR-Schädigungsprozess in Fahrbahndecken aus Beton grundlegend zu klären, sind zwei aufeinander aufbauende Untersuchungsschwerpunkte Gegenstand dieses Beitrags. Im ersten Schwerpunkt wurden die prüftechnischen Voraussetzungen für die Charakterisierung der Degradation und damit der Rissbildung im Fahrbahndeckenbeton durch die Vorschädigung infolge von Ermüdungsbeanspruchungen geschaffen. Realisiert wurde dies durch die Implementierung und Optimierung eines Monitoringsystems im zyklischen 4-Punkt-Biegeversuch zur simultanen Erfassung der Rissbildung im großformatigen Schwingbalken. Zusätzlich wurde die Röntgen-3D-Computertomografie für die hochauflösende räumliche quantitative Rissanalyse in den Bohrkernen aus den Schwingbalken ohne und mit Vorschädigung weiterentwickelt. Im zweiten Untersuchungsschwerpunkt wurde mittels vielfältiger Experimente an kleinformatigen Probekörpern aus dem Schwingbalken gezeigt, dass durch die Ermüdungsbeanspruchung die bruchmechanischen Materialkennwerte des Betons zum Teil eine signifikante Veränderung erfahren. Based on the objective of the DFG (German research foundation) funded research group 1498 to clarify the influences on the ASR damage process, this paper deals with two focuses of investigation. In the first focus the technical requirements for the characterisation concerning the degradation and the formation of cracks in concrete pavements by the pre-damage as a result of fatigue loading were created. This was realized by the implementation and the optimisation of a monitoring system in the cyclic four point bending test to capture simultaneously the formation of cracks in the beam under sinusoidal bending load. In addition, the X-ray 3D-computed tomography was enhanced for the high-resolution quantitative spatial crack analysis in the drilling cores extracted of the beam under sinusoidal bending load without and with a pre-damage. Building on the first focus, in the second focus of investigation a significant change of the fracture-mechanical properties of the concrete as a result of fatigue loading has been demonstrated in numerous experiments using small specimens extracted from the beam under sinusoidal bending load. KW - Beton KW - CT KW - ROI KW - Risserkennung PY - 2015 DO - https://doi.org/10.1002/best.201400096 SN - 0005-9900 SN - 1437-1006 VL - 110 IS - 1 SP - 22 EP - 33 PB - Ernst CY - Berlin AN - OPUS4-32517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waurischk, Tina A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Chen, Y.-F. A1 - Contreras Jaimes, A. T1 - Datengetriebener Workflow für die beschleunigte Entwicklung von Glas (GlasDigital) N2 - Das Projekt GlasDigital wurde im allgemeinen vorgestellt, sowie die einzelnen Zwischenstände der verschiedenen Arbeitspakete aller Projektpartner präsentiert. Die allgemeine Porjektvorstellung ist auf deutsch. Die Zwischenstände der Arbeitsinhalte sind auf englisch. T2 - PMD Vollversammlung CY - Berlin, Germany DA - 03.11.2022 KW - Oxidglas KW - Robotische Glasschmelzanlage KW - ML KW - Ontologie KW - Digitaler Zwilling KW - Bildanalyse PY - 2022 AN - OPUS4-56491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, A. A1 - Goecke, S.-F. A1 - Sievi, P. A1 - Albert, F. A1 - Rethmeier, Michael T1 - Laser beam oscillation strategies for fillet welds in lap joints N2 - Laser beam oscillation opens up new possibilities of influencing the welding process in terms of compensation of tolerances and reduction of process emissions that occur in industrial applications, such as in body-in-white manufacturing. The approaches are to adapt the melt pool width in order to generate sufficient melt volume or to influence melt pool dynamics, e.g. for a better degassing. Welding results are highly dependent on the natural frequency of the melt pool, the used spot diameter and the oscillation speed of the laser beam. The conducted investigations with an oscillated 300 µm laser spot show that oscillation strategies, which are adjusted to the joining situation improve welding result for zero-gap welding as well as for bridging gaps to approximately 0.8 mm. However, a complex set of parameters has to be considered in order to generate proper welding results. This work puts emphasize on introducing them. KW - Laser beam welding KW - Gap compensation KW - Process monitoring and control KW - System technology KW - Automotive application PY - 2014 DO - https://doi.org/10.1016/j.phpro.2014.08.149 SN - 1875-3892 VL - 56 SP - 458 EP - 466 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-31437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, A. A1 - Goecke, S.F. A1 - Rethmeier, Michael T1 - Laser beam oscillation welding for automotive applications N2 - Laser beam oscillation, applied one- or two-dimensional to the actual welding process, influences the welding process in terms of compensation of tolerances and reduction of process emissions like spatter and melt ejections that occur in industrial applications, such as in body-in-white manufacturing. If the welding process could be adapted to these tolerances by the momentarily demanded melt pool width to generate sufficient melt volume or to influence melt pool dynamics, e.g. for a better degassing, laser welding would become more robust. However, beam oscillation results are highly dependent on the natural frequency of the melt pool, the used spot diameter and the oscillation speed of the laser beam. The conducted investigations with an oscillated 300 μm laser spot show that oscillation strategies which are adjusted to the joining situation can bridge gaps to approximately 0.6 mm at metal sheet thickness of 0.8 mm. However, the complex behaviour of the melt pool has to be considered to generate proper welding results. This work puts emphasis on showing aspects of beam oscillation in fillet welding in lap joints. KW - Automotive application KW - Melt pool dynamics KW - Adaptive welding beam oscillation KW - Laser welding KW - Gap bridging PY - 2018 DO - https://doi.org/10.1007/s40194-018-0625-3 SN - 0043-2288 SN - 1878-6669 VL - 62 IS - 5 SP - 1039 EP - 1047 PB - Springer AN - OPUS4-45774 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Albert, F. A1 - Baum, S. A1 - Goecke, S. A1 - Müller, A. A1 - Sievi, P. A1 - Rethmeier, Michael T1 - Nahtgeführtes Laserstrahl-Remoteschweißen mit Strahloszillation - Beeinflussung der Schweißnahtanmutung, der Schweißnahtgeometrie und der Spaltüberbrückbarkeit PY - 2013 SN - 0036-7184 VL - 65 IS - 9 SP - 631 EP - 635 PB - Verl. für Schweißen u. Verwandte Verfahren, DVS-Verl. CY - Düsseldorf AN - OPUS4-29300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, A. A1 - Goecke, S.F. A1 - Rethmeier, Michael T1 - Laser beam oscillation for fillet welding N2 - In today’s automotive frame-and-body construction, laser welds are typically carried out as square butt welds in lap joints. These welds are increasingly produced by remote laser welding optics with working distances of 500 mm and more. This enables simple path programming because clamping devices are traversed over and therefore low cycle times with improved productivity is achieved. However, workpiece tolerances lead to part displacements and varying joint positions over time. These displacements have to be acted against by appropriate flange length that contain for positioning deviations. Using this concept, aspired light-weight optimisations, e.g. reducing flange length, are difficult to achieve. By using seam tracking sensors, part tolerances are automatically detected and counteracted for. In addition, joint edge detection allows constructive changes on the type of weld. Fillet welds reduce flange lengths', improve force flow and open up possibilities for visual quality monitoring. Apart from that, vertical displacements in the form of height tolerances still occur. This needs consideration by adapting the set of welding parameter to the current welding situation. In this respect, one main welding parameter is the lateral beam offset to the upper sheet. Since body-in-white welding applications mainly comprise of zinc-coated steel sheets, special requirements for the welding process are given. Especially zero-gap-welding and welding of joints with gaps larger than 0.2 mm are critical. Using a laser beam oscillation process can stabilise these situations. Approaches to finding parameter sets are presented in this paper. KW - Laser beams KW - Welding KW - Fillet welds KW - Gap KW - Process procedures KW - Monitoring systems PY - 2014 DO - https://doi.org/10.1007/s40194-014-0165-4 SN - 0043-2288 SN - 1878-6669 VL - 58 IS - 6 SP - 865 EP - 872 PB - Springer CY - Oxford AN - OPUS4-32075 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Massiot, D. A1 - Müller, D. A1 - Hübert, Thomas A1 - Schneider, M. A1 - Kentgens, A. A1 - Coté, B. A1 - Coutures, J. A1 - Gessner, W. T1 - Double rotation and magic-angle spinning nuclear magnetic resonance study of 27Al: reexamination of the aluminium borate 9Al2O3 · 2B2O3 N2 - 27Al nuclear magnetic resonance spectra of polycrystalline aluminium borate 9Al2O3 · 2B2O3 have been measured in double rotation at 11.7 and 7.0 T and high-speed magic-angle spinning at 7.0, 9.4, 11.7, 14.1 and 17.6 T. Spinning sidebands from the satellite transitions were observed at 7.0 and 14.1 T. Each of the four structural aluminium sites [Al(IV), Al(V)(1), Al(V)(2) and Al(VI)] are observed, characterised and assigned in the spectra. The obtained parameter set gives a fully consistent interpretation in agreement with the crystal structure of the compound. KW - Aluminium KW - Kernresonanz, magnetisch KW - Winkel, magisch KW - Doppelrotation PY - 1995 DO - https://doi.org/10.1016/0926-2040(95)00021-H SN - 0926-2040 SN - 1527-3326 VL - 5 IS - 2 SP - 175 EP - 180 PB - Academ. Press CY - Orlando, Fla. AN - OPUS4-639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, V. A1 - Marko, A. A1 - Kruse, T. A1 - Biegler, M. A1 - Rethmeier, Michael T1 - Analysis and recycling of bronze grinding waste to produce maritime components using directed energy deposition N2 - Additive manufacturing promises a high potential for the maritime sector. Directed Energy Deposition (DED) in particular offers the opportunity to produce large-volume maritime components like propeller hubs or blades without the need of a costly casting process. The post processing of such components usually generates a large amount of aluminum bronze grinding waste. The aim of the presented project is to develop a sustainable circular AM process chain for maritime components by recycling aluminum bronze grinding waste to be used as raw material to manufacture ship Propellers with a laser-powder DED process. In the present paper, grinding waste is investigated using a dynamic image Analysis system and compared to commercial DED powder. To be able to compare the material quality and to verify DED process parameters, semi-academic sample geometries are manufactured. T2 - LiM 2021 CY - Munich, Germany DA - 21.06.2021 KW - Additive Manufacturing KW - Maritime Components KW - Powder Analysis KW - Recycling KW - Directed Energy Deposition PY - 2021 SP - 1 EP - 9 AN - OPUS4-54067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tognoni, E. A1 - Cristoforetti, G. A1 - Legnaioli, S. A1 - Palleschi, V. A1 - Salvetti, A. A1 - Müller, Maike A1 - Panne, Ulrich A1 - Gomushkin, I. T1 - A numerical study of expected accuracy and precision in Calibration-Free Laser-Induced Breakdown Spectroscopy in the assumption of ideal analytical plasma N2 - Calibration-Free Laser-Induced Breakdown Spectroscopy (CF-LIBS) has been proposed several years ago as an approach for quantitative analysis of Laser-Induced Breakdown Spectroscopy spectra. Recently developed refinement of the spectral processing method is described in the present work. Accurate quantitative results have been demonstrated for several metallic alloys. However, the degree of accuracy that can be achieved with Calibration-Free Laser-Induced Breakdown Spectroscopy analysis of generic samples still needs to be thoroughly investigated. The authors have undertaken a systematic study of errors and biasing factors affecting the calculation in the Calibration-Free Laser-Induced Breakdown Spectroscopy spectra processing. These factors may be classified in three main groups: 1) experimental aberrations (intensity fluctuations and inaccuracy in the correction for spectral efficiency of a detection system), 2) inaccuracy in theoretical parameters used for calculations (Stark broadening coefficients and partition functions) and 3) plasma non-ideality (departure from thermal equilibrium, spatial and temporal inhomogeneities, optical thickness, etc.). In this study, the effects of experimental aberrations and accuracy of spectral data were investigated, assuming that the analytical plasma is ideal. Departure of the plasma conditions from ideality will be the object of future work. The current study was based on numerical simulation. Two kinds of metallic alloys, iron-based and aluminum-based, were studied. The relative weight of the error contributions was found to depend on the sample composition. For the here-investigated samples, the experimental aberrations contribute to the overall uncertainty on the quantitative results more than theoretical parameters. The described simulation method can be applied to the Calibration-Free Laser-Induced Breakdown Spectroscopy analysis of any other kind of sample. KW - LIBS KW - Quantitative analysis KW - Standard-less analysis KW - Accuracy KW - Precision PY - 2007 DO - https://doi.org/10.1016/j.sab.2007.10.005 SN - 0584-8547 SN - 0038-6987 VL - 62 IS - 12 SP - 1287 EP - 1302 PB - Elsevier CY - Amsterdam AN - OPUS4-16566 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kasche, J. A1 - Dahms, A. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Müller, D. T1 - Sensory evaluation of building products - Results of a German round robin test T2 - VDI-Tagung CY - Bad Kissingen, Deutschland DA - 2007-11-13 KW - Bauprodukte KW - Emissionen KW - Geruch KW - AbBB-Schema KW - Kammermessungen KW - Blauer Engel PY - 2007 SN - 978-3-18-091995-9 SN - 0083-5560 IS - 1995 SP - 193 EP - 202 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-16322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dal Molin, E. S. A1 - Henning, L. M. A1 - Müller, J. T. A1 - Smales, Glen Jacob A1 - Pauw, Brian Richard A1 - Bekheet, M. F. A1 - Gurlo, A. A1 - Simon, U. T1 - Robocasting of ordered mesoporous silica‐based monoliths: Rheological, textural, and mechanical characterization N2 - Hierarchically porous, high‐surface‐area silica materials are excellent candidates for multiple applications like catalysis and environmental remediation. Shaping these materials with additive manufacturing (AM) techniques, like robocasting, could enable their use with the benefit of on‐demand, customized shaping and maximizing performance. Herein, ordered mesoporous silica COK‐12 slurries were robocasted into monoliths, containing different ratios of uncalcined COK‐12 and sodium bentonite (0–25 wt.%). The rheology of the mixed slurries is characterized by lower flow indexes (0.69 vs. 0.32) and higher yield stresses (96 vs. 259 Pa) compared to pure COK‐12 ones. Monoliths were printed in woodpile structures and calcined at 600°C. Micro‐CT measurements showed a linear shrinkage of 25% after calcination. Mechanical characterization showed increased uniaxial strength (0.20 ± 0.07 to 1.0 ± 0.3 MPa) with increasing binder/solids ratio from 13 to 25%. The amorphous, mesoporous structure of COK‐12 was retained. The structures exhibited open porosities of 52 ± 4% and showed higher specific mesopore volumes, and increased average mesopore size (6 vs. 8 nm) compared to COK‐12. Small‐angle x‐ray scattering analysis revealed an increased lattice parameter (10.3 vs. 11.0 nm) and reduced wall thickness (3.1 nm vs. 4.1 nm) of the COK‐12 in the monoliths. These properties indicate suitability for their application as porous supports and adsorbents. KW - Industrial and Manufacturing Engineering KW - Additive manufacturing KW - OMS KW - Porous materials KW - Robocasting KW - X-ray scattering KW - MOUSE PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582503 DO - https://doi.org/10.1002/nano.202300109 VL - 4 IS - 11-12 SP - 615 EP - 631 PB - Wiley-VCH GmbH AN - OPUS4-58250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - König, S. A1 - Diersch, R. A1 - Lührmann, A. A1 - Müller, Karsten A1 - Neumann, Martin A1 - Quercetti, Thomas A1 - Droste, Bernhard T1 - Full-Scale Drop Testing of the CONSTOR®, V/TC Package Program, and Preliminary Results KW - Drop test KW - Package KW - Spent fuel cask KW - Transport PY - 2005 SN - 0893-6188 VL - 33 IS - 3 SP - 4 EP - 10 PB - Institute of Nuclear Materials Management CY - Northbrook, Ill. AN - OPUS4-12269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - König, S. A1 - Diersch, R. A1 - Lührmann, A. A1 - Müller, Karsten A1 - Neumann, Martin A1 - Quercetti, Thomas A1 - Droste, Bernhard T1 - Full-scale Drop Testing of the CONSTOR V/TC Package - Program and Preliminary Results KW - Fallversuche KW - Transportbehälter für radioaktive Stoffe PY - 2005 SN - 0893-6188 VL - 33 IS - 3 SP - 4 EP - 10 PB - Institute of Nuclear Materials Management CY - Northbrook, Ill. AN - OPUS4-6875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gogula, Shravya A1 - Bornhöft, H. A1 - Wondraczek, L. A1 - Sierka, M. A1 - Diegeler, A. A1 - Müller, Ralf A1 - Deubener, J. T1 - Optical Real-Time Castability Evaluation for High-Throughput Glass Melting N2 - A novel optical real-time method for evaluating the castability of glass forming melts for laboratory furnaces is presented. The method is based on the analysis of top view images of the melt surface inside the crucible during melting after being subjected to a small mechanical impulse. In this way, the melt surface is excited to oscillate. The difference in contrast between two images taken in quick succession scales with the viscosity, with a larger diffe­rence occurring at lower viscosities. The method is designed as an instrument for the in-line evaluation of the castability for a high-throughput glass melting system as part of the joint project “GlasDigital” in the framework of the German Platform Material Digital initiative but is applicable to other laboratory furnaces as well. KW - Optical Real-Time Castability Check KW - Image Analysis PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618659 DO - https://doi.org/10.52825/glass-europe.v2i.1359 VL - 2 SP - 83 EP - 93 AN - OPUS4-61865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Blaeß, Carsten A1 - Boccaccini, A. R. A1 - Müller, Ralf T1 - Sintering and Crystallization of Fluoride-Containing Bioactive Glass F3 N2 - The fluoride-containing bioactive glass F3 with nominal composition (mol%) 44.8 SiO2 - 2.5 P2O3 - 36.5 CaO - 6.6 Na2O - 6.6 K2O - 3.0 CaF2 is a highly promising candidate for bone replacement applications. Its strong crystallization tendency, however, requires a thorough understanding of the interplay between glass powder particle size, surface crystallization, and sintering. Therefore, this study characterizes the sintering and crystallization of bulk specimens and various particle size fractions by differential thermal-analysis, laser scanning, electron microscopy, X-ray diffraction, and Infrared spectroscopy. Particle size fractions < 56 µm were found to fully densify, while crystals growing from the glass particle surface retard sintering of coarser fractions. Small amounts of a non-stoichiometrically calcium phosphosilicate (Ca14.92(PO4)2.35(SiO4)5.65) occurs as the primary crystal phase followed by combeite (Na4Ca4[Si6O18]) as a temporarily dominating phase. The surface crystallization of both pha­ses was found to be mainly responsible for sinter retardation. During later stages of crystallization, additional phases such as cuspidine (Ca4F2Si2O7) and silicorhenanite (Na2Ca4(PO4)2SiO4) occur, but finally monoclinic wollastonite (CaSiO3) forms as the dominant phase. KW - Bioactive Glass KW - Sintering KW - Crystallization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-632482 DO - https://doi.org/10.52825/glass-europe.v3i.2564 SN - 2940-8830 VL - 3 SP - 105 EP - 124 AN - OPUS4-63248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Deubener, J. A1 - Allix, M. A1 - Davis, M.J. A1 - Duran, A. A1 - Höche, T. A1 - Honma, T. A1 - Komatsu, T. A1 - Krüger, S. A1 - Mitra, I. A1 - Müller, Ralf A1 - Nakane, S. A1 - Pascual, M.J. A1 - Schmelzer, J.W. A1 - Zanotto, E.D. A1 - Zhou, S. T1 - Updated definition of glass-ceramics N2 - Glass-ceramics are noted for their unusual combination of properties and manifold commercialized products for consumer and specialized markets. Evolution of novel glass and ceramic processing routes, a plethora of new compositions, and unique exotic nano- and microstructures over the past 60 years led us to review the Definition of glass-ceramics. Well-established and emerging processing methods, such as co-firing, additive manufacturing, and laser patterning are analyzed concerning the core requirements of processing glass-ceramics and the Performance of the final products. In this communication, we propose a revised, updated definition of glass-ceramics, which reads “Glass-ceramics are inorganic, non-metallic materials prepared by controlled crystallization of glasses via different processing methods. They contain at least one type of functional crystalline phase and a residual glass. The volume fraction crystallized may vary from ppm to almost 100%”. KW - Glass-ceramics definition PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-464711 DO - https://doi.org/10.1016/j.jnoncrysol.2018.01.033 SN - 0022-3093 SN - 1873-4812 VL - 501 SP - 3 EP - 10 PB - Elsevier B.V. AN - OPUS4-46471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eberstein, Markus A1 - Thiel, A. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Deubener, J. A1 - Schiller, Wolfgang Arno T1 - Lösungs- und Kristallisationsvorgänge beim Sintern von Glasmatrix-Kompositen T2 - 79. Glastechnische Tagung CY - Würzburg, Deutschland DA - 2005-05-23 KW - Glaspulver KW - Glasmatrix-Komposit KW - Sintern KW - Kristallisation PY - 2005 SN - 3-921089-43-3 SP - 7 Seiten PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-10377 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eberstein, Markus A1 - Thiel, A. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Deubener, J. A1 - Schiller, Wolfgang Arno T1 - Sinterkinetik von Glasmatrix-Kompositen mit reaktiver Dispersphase T2 - 80. Glastechnische Tagung CY - Dresden, Deutschland DA - 2006-06-12 PY - 2006 SN - 3-921089-46-8 SP - 4 Seiten PB - Verl. d. Dt. Glastechn. Ges. CY - Offenbach AN - OPUS4-14046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Reinsch, Stefan A1 - Meng, S. A1 - Eberstein, Markus A1 - Thiel, A. A1 - Müller, Ralf A1 - Deubener, J. T1 - Partial Solution of Dispersed alpha-Al2O3-Particles in Alumoborosilicate Glass T2 - 81. Glastechnische Tagung CY - Aachen, Deutschland DA - 2007-06-04 KW - Glasmatrixkomposite KW - Lösung KW - Sintern PY - 2007 SN - 978-3-921089-52-1 IS - CD-ROM SP - 1 EP - 5 PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-16108 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Ralf A1 - Eberstein, Markus A1 - Reinsch, Stefan A1 - Schiller, Wolfgang Arno A1 - Deubener, J. A1 - Thiel, A. T1 - Effect of rigid inclusions on sintering of low temperature co-fired ceramics KW - Sintering KW - Glass Matrix Composites KW - Rigid Inclusion KW - Effective Viscosity KW - Kinetic Modelling KW - LTCC PY - 2007 SN - 1753-3562 SN - 0017-1050 SN - 0031-9090 SN - 1750-6697 VL - 48 IS - 4 SP - 259 EP - 266 PB - Society of Glass Technology CY - Sheffield AN - OPUS4-16211 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Apel, E. A1 - Deubener, J. A1 - Bernard, A. A1 - Müller, Ralf A1 - Kappert, H. A1 - Rheinberger, V. A1 - Höland, W. T1 - Phenomena and mechanisms of crack propagation in glass-ceramics N2 - Lithium disilicate, leucite and apatite glass-ceramics have become state-of-the-art framework materials in the fabrication of all-ceramic dental restorative materials. The goal of this study was to examine the crack propagation behaviour of these three known glass-ceramic materials after they have been subjected to Vickers indentation and to characterize their crack opening profiles (δmeas vs. (a-r)). For this purpose, various methods of optical examination were employed. Optical microscopy investigations were performed to examine the crack phenomena at a macroscopic level, while high-resolution techniques, such as scanning electron microscopy (SEM) and atomic force microscopy (AFM), were employed to investigate the crack phenomena at a microscopic level. The crack patterns of the three glass-ceramics vary from fairly straightforward to more complex, depending on the amount of residual glass matrix present in the material. The high-strength lithium disilicate crystals feature a high degree of crosslinking, thereby preventing crack propagation. In this material, the crack propagates only through the residual glass phase, which constitutes 30%–40% by volume. Having a high glass content of more than 65% by volume, the leucite and apatite glass-ceramics show far more complex crack patterns. Cracks in the leucite glass-ceramic propagate through both the glass and crystal phase. The apatite glass-ceramic shows a similar crack behaviour as an inorganic–organic composite material containing nanoscale fillers, which are pulled out in the surroundings of the crack tip. The observed crack behaviour and the calculated View the MathML source values of the three types of glass-ceramics were compared to the Kkic values determined according to the SEVNB method. KW - Glass KW - Viscosity KW - Water content PY - 2008 DO - https://doi.org/10.1016/j.jmbbm.2007.11.005 SN - 1751-6161 VL - 1 IS - 4 SP - 313 EP - 325 PB - Elsevier CY - Amsterdam AN - OPUS4-18308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Ralf A1 - Reinsch, Stefan A1 - Eberstein, Markus A1 - Deubener, J. A1 - Thiel, A. A1 - Schiller, Wolfgang Arno T1 - Effects of dispersed Al2O3 particles on sintering of LTCC N2 - The sintering of Low Temperature Co-fired Ceramics prepared from alumoborosilicate glass- and Al2O3 powders of similar small particle size was studied by dilatometry, heating microscopy, microstructure analysis, glass- and effective viscosity measurements. The steric effect of Al3O3 inclusions was studied using a gnon-reactiveh model composite. With increasing Al3O3 volume fraction (Φ ≤ 0.45), sintering decelerates and its final stage shifts to higher temperature. The attainable shrinkage is reduced as Al2O3 particle clusters bearing residual pores become more frequent. The kinetics of sintering could be described formally superposing the weighed contributions of differentially sized and randomly composed glass-crystal particle clusters and assuming a sintering rate controlled by the effective matrix viscosity, which increases with Φ and with progressive wetting of Al2O3 particles during densification. The "reactive" model composite shows significant dissolution of Al2O3 into the glass, which has two opposed effects on sintering: reducing Φ and increasing glass viscosity. For the present case (Φ = 0.25), the latter effect dominates and sintering is retarded by Al2O3 dissolution. Crystallization of wollastonite starts after full densification. Dissolution of Al2O3 was found to promote the subsequent growth of anorthite. KW - LTCC KW - Glass matrix composites KW - Al2O3-inclusions KW - Sintering kinetics PY - 2005 SN - 1022-6680 SN - 1662-8985 VL - 39-40 SP - 375 EP - 380 PB - Trans Tech Publ. CY - Zurich AN - OPUS4-18441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -