TY - CONF A1 - Schmidt, Birgit Angelika T1 - Dekontamination Biozid-belasteter Kulturgüter auf organischer Basis durch den Einsatz von Lasertechnologie N2 - Im Rahmen des DBU-Verbundprojektes „Dekontaminierng von Biozid-belasteten Kulturgütern mittels Plasma und Laser (DekoPla)“ wurde durch den Einsatz von kurz- und ultrakurz gepulsten Lasern eine Oberflächenreinigung und eine Chlorabreicherung von mit Hylotox 59 behandelten Holzoberflächen angestrebt. Probenmaterial wurde freundlicherweise vom Schlossmuseum in Sonderhausen zur Verfügung gestellt. Es handelt sich dabei um kontaminiertes Altholz mit natürlicher Biozidalterung. Darüber hinaus weisen die einst als Gemälderückseitenschutz und Originalbauteil der „Goldenen Kutsche“ fungierenden Prüfkörper leichte Verschmutzungen auf den Oberflächen auf. Das Holzschutzmittel Hylotox 59 beinhaltet die Wirkstoffe DDT (Dichlor-Diphenyl-Trichlorethan) und Lindan. DDT ist an den Holzoberflächen als mikrokristalline Ausblühung präsent. Zur Beurteilung des Erfolges des Lasereinsatzes wurde vor und nach der Laserbehandlung am gleichen Ort auf der Probenoberfläche ein Chlornachweis mittels Röntgenfluoreszenzanalytik (RFA) erbracht. Aus der Differenz der Chlorsignale und mit einer entsprechenden Normierung wird auf die Chlorabreicherung geschlossen. Die Ergebnisse dieser Messungen werden in Chlorverteilungsbildern veranschaulicht. Darüber hinaus erfolgte eine Dokumentation mit lichtmikroskopischen Aufnahmen. T2 - Workshop Innovationsforum Inn-O-Kultur, DBU-Abschlusskolloquium „Dekontamination von Biozid-belasteten Kulturgütern mittels neuer Laser- und Plasmatechnologie“ CY - Sondershausen, Germany DA - 14.12.2016 KW - Dekontamination KW - DDT KW - Holz KW - Laserreinigung KW - Ultrakurzpulslaser PY - 2016 AN - OPUS4-38901 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Birgit Angelika T1 - Decontamination of biocidal loaded wooden artworks by means of laser and plasma processing N2 - Many wooden artworks are contaminated by DDT (dichlorodiphenyltrichloroethane) as a result of a surface treatment by means of Hylotox-59©. The liquid preservative was used until the end of the 80s. DDT crystal structures are formed on the wood surfaces by the "blooming" of chlorine compounds. Contaminated waste wood with natural biocide ageing, gilded and wood carved elements of an old picture frame and wooden samples with paint layers were provided by the Schlossmuseum Sondershausen. The removal of DDT was evaluated employing femtosecond and nanosecond laser radiation and cold atmospheric plasma technique using different working gases (air, nitrogen, and argon). Before laser application, a chlorine measurement is done by X-ray fluorescence (XRF) analysis as reference. After laser processing, the XRF analysis is used again at the same surface position to determine depletion rates. Additionally, a documentation and characterization of the sample surface is done before and after laser and plasma treatment using optical microscopy. For plasma processing with various systems a chlorine measurement is done by gas chromatographic-mass spectrometry (GCMS) analysis. For laser treatment a depletion of the chlorine concentration of 55-70% and 75% was achieved for 1064-nm nanosecond pulses and 800-nm femtosecond pulses, respectively. For the application of 30-fs laser pulses, no crystalline DDT residues remain on the sample surfaces. This holds also for the plasma processing with nitrogen as working gas. T2 - Conference on Lasers in the Conservation of Artworks (LACONA XI) CY - Krakow, Poland DA - 19.09.2016 KW - Decontamination KW - Wood KW - DDT KW - Laser cleaning KW - Plasma treatment PY - 2016 AN - OPUS4-38903 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Sebastian Hanns-Otto T1 - Wide-spectrum dielectric functions of ALD deposited oxides relevant for photovoltaics N2 - Silicon surface passivation with atomic layer deposited (ALD) thin films has gained more and more interest in the PV community in recent years. With ALD good film quality, accurate thickness control and conformity are reached. Furthermore, ALD is capable of coating difficult substrates such as nanostructured surfaces with the same accuracy as flat surfaces. A variety of materials such as Al2O3, TiO2 and HfO2 demonstrate good surface passivation quality both for front and rear surface of silicon solar cells. In addition of providing good surface passivation, thin films with high refractive index e.g. HfO2, TiO2 and AlN can act simultaneously as antireflection coatings when applied on the front surface of the device. Hence, ALD thin films can reduce both electrical and reflective losses in solar cells. Thorough investigation of the optical properties of these layers is crucial for several reasons related to their production and use. Optical measurements provide a fast, easy, non-destructive, and in situ capable approach to quality assurance for photovoltaic devices. As the function of the final device is optical, optimisation of the device performance relies strongly on the knowledge of the wide-range dielectric function of the thin layers. In this contribution, we determined the optical constants of ALD generated layers of AlN, Al2O3, TiO2, and HfO2 in a wide spectral range covering the near ultraviolet and the mid-infrared regions by means of spectroscopic ellipsometry. By combining data from a UV-Vis-NIR ellipsometer (Woollam M2000DI) and an FTIR ellipsometer (Sentech Sendira), we can determine the optical constants alongside with the layer thicknesses from one large set of spectroscopic measurements. We consider this a contribution to the metrological treatment of stratified and structured thin films in the optical range by polarisation-sensitive measurement methods. T2 - International conference on spectroscopic ellipsometry (ICSE 7) CY - Berlin, Germany DA - 06.06.2016 KW - ALD (atomic layer deposited) KW - Ellipsometry KW - Photovoltaic KW - Solar Cell KW - HfO2 KW - Aln KW - Al2O3 KW - TiO2 PY - 2016 AN - OPUS4-37222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Interlaboratory Test 2015 "EN 15188" - Ergebnisse und Schlussfolgerungen N2 - Ergebnisse des Ringversuches "DIN EN 15188: Determination of the spontaneous ignition behaviour of dust acuumulations T2 - Industriearbeitskreis "Brennbare Stäube" CY - Wolfgang-Hanau, Germany DA - 28.06.2016 KW - Selbstentzündung KW - Ringversuch KW - Methodenvalidierung KW - Messunsicherheit PY - 2016 AN - OPUS4-37196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Martin A1 - Wu, D. A1 - Norman, F. A1 - Vanierschot, M. A1 - Verplaetsen, F. A1 - Berghmans, J. A1 - van den Bulck, E. T1 - Numerical investigation on the self-ignition behaviour of coal dust accumulations: The roles of oxygen, diluent gas and dust volume N2 - Self-ignition of coal dust deposits poses a higher risk of fires in oxygen-enriched oxy-fuel combustion systems. In this work, we develop a numerical method, using the commercial software COMSOL Multiphysics, to investigate self-ignition behaviour of coal dust accumulations with a main emphasis on the roles of oxygen, diluent gas and dust volume. A one-step 2nd-order reaction kinetic model considering both coal density and oxygen density is used to estimate reaction rate using the kinetic parameters from previously conducted hot-oven tests. This model is validated to predict the transient temperature and concentration profiles of South African coal dusts until ignition. The computed self-ignition temperatures of dust volumes show a good agreement with experimental results. In addition, it is found that the inhibiting effect of carbon dioxide is comparatively small and oxygen consumption increases dramatically after ignition. Parameter analysis shows that the heating value and kinetic parameters have a comparatively pronounced effect on self-ignition temperature. The model provides a satisfactory explanation for the dependence of self-ignition behaviour on gas atmospheres, thus helping to further understand the fire risk of self-ignition in oxy-fuel combustion systems. KW - Ignition temperature KW - Oxy-fuel combustion KW - Fire safety KW - Self-ignition KW - Numerical simulation PY - 2017 DO - https://doi.org/10.1016/j.fuel.2016.10.063 SN - 0016-2361 SP - 500 EP - 510 AN - OPUS4-37885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Stephan T1 - Synthetic Strategies to obtain Haptens for the Production of antibodies against Diclofenac T2 - Tag der Biotechnologie CY - Berlin, Germany DA - 2015-07-16 PY - 2015 AN - OPUS4-33777 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Schmidt, Martin T1 - Nanoskalig hergestellte Materialien - neueste Erkenntnisse N2 - Die steigende Produktion und Nachfrage von Materialien mit Primärpartikelgrößen im Nanometerbereich (insbesondere wegen der veränderten Eigenschaften) erfordert eine intensive Auseinandersetzung mit der Thematik zur Risikoabschätzung. Sogenannte Nanostäube können aus brennbaren Ausgangsmaterialien bestehen. Beispiele für brennbare Nanostäube, die in großen Mengen hergestellt werden, sind Metallstäube, Ruße (Carbon Black) oder andere Kohlenstoffverbindungen, welche u. a. für die Herstellung von Gummi, Kunststoffen, Beschichtungsstoffen oder Farben verwendet werden. Aufgrund von Erfahrungen mit Stäuben mit Partikelgrößen im Mikrometerbereich ist bekannt, dass Stoffe mit abnehmender Partikelgröße kritischer einzustufen sind, da z.B. maximaler Explosionsdruck, zeitlicher Druckanstieg und Zündempfindlichkeit durch die Zunahme der reaktiven Oberfläche des Staubes zunimmt. Alle Erkenntnisse zum Ablauf von Staubexplosionen, aus der Auswertung von Schadensereignissen sowie aus der Bestimmung sicherheitstechnischer Kenngrößen und hierbei gefundene Abhängigkeiten basieren auf Schadensereignissen bzw. Untersuchungen von Stäuben mit Korngrößen im Bereich von Mikrometern. Inwieweit sich die Erkenntnisse auf feinere Partikel bis hin zum Nanometerbereich übertragen lassen, wurde im Rahmen der durchgeführten Arbeiten näher untersucht. In diesem Beitrag werden die wesentlichen Ergebnisse kurz dargestellt und basieren auf den Arbeiten im Zuge der Dissertationsschrift zum Brand- und Explosionsverhalten von Nanostäuben. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Explosionsschutz KW - Brennbare Stäube KW - Nanomaterialien KW - Nanostäube PY - 2015 SN - 978-3-86011-091-1 SP - F-01 EP - 1-10 AN - OPUS4-34943 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Klippel, Alexander T1 - Der Einfluss des Staubungsverhaltens auf druckentlastete Staubexplosionen - experimentelle und numerische Untersuchungen N2 - Die Auslegung von Einrichtungen zur Druckentlastung von Staubexplosionen erfolgt in der Regel gemäß DIN EN 14491. Die Norm enthält empirische Gleichungen mit denen, unter Verwendung der sicherheitstechnischen Kenngrößen maximaler Explosions(über)druck und maximaler zeitlicher Druckanstieg bzw. dem KSt-Wert, erforderliche Entlastungsflächen zum konstruktiven Schutz von Behältern und Anlagen berechnet werden. Das Verfahren ermög-licht in der Regel eine konservative Auslegung von Entlastungsflächen. Zur praxisgerechte-ren Betrachtung erfolgten der Vergangenheit bereits Untersuchungen zum Einfluss bestimm-ter Verfahren zur Produkteinleitung bzw. Befüllung auf die Bildung von Staubwolken in Silos oder Behältern, welche einen wesentlichen Einfluss auf die erforderliche Druckentlastungs-fläche aufweisen. Bisher unberücksichtigt blieb, dass die Bildung von Staubwolken sehr stark von den chemischen und physikalischen Eigenschaften des Schüttgutes abhängt. Da auch bei scheinbar ähnlichen Produkten das Aufwirbel- und Schwebeverhalten sehr unterschied-lich sein kann, ist hierdurch ein erheblicher Einfluss auf die Bildung explosionsfähiger Staub/Luft-Gemische und damit auf die erforderliche Entlastungsfläche zu erwarten. Ziel experimenteller und numerischer Untersuchungen war es daher, den Einfluss des Ver-mögens von Stäuben aufgewirbelt zu werden bzw. deren Dispergierverhalten in Luft auf die erforderliche Druckentlastungsfläche zu ermitteln. Hierbei sollte überprüft werden, inwieweit bei Stäuben mit geringer Staubungsneigung eine Verringerung der Druckentlastungsfläche möglich ist. Die durchgeführten Untersuchungen zeigten, dass die Randbedingungen, insbesondere die Strömungsrandbedingungen, die bei einem Verarbeitungs- oder Förderprozess vorliegen, einen wesentlich stärkeren Einfluss auf die Dispergierung eines Staubes aufweisen als sein Staubungsverhalten. Eine Anpassung bzw. Reduzierung der Druckentlastungsfläche allein auf Basis des Staubungsverhaltens ist daher nicht möglich. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Staubexplosionen KW - Staubungsverhalten KW - Explosionsschutz PY - 2015 SN - 978-3-86011-091-1 SP - C-03, 1-15 AN - OPUS4-34944 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, S. T1 - An Advanced Method for Pedestrian Dead Reckoning using BLSTM-RNNs T2 - IPIN 2015, 6th International Conference on Indoor Positioning and Indoor Navigation CY - Banff, Alberta, Canada DA - 2015-10-13 PY - 2015 AN - OPUS4-35031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Ziel, methodisches Konzept und Ergebnisse des Interlaboratory test 2010/11 "DIN EN 15188:2007 - self ignition temperature" T2 - Kolloquium des Arbeitskreises "Brennbare Stäube": Interlaboratory test 2010/11 DIN EN 15188:2007 - self-ignition temperature" CY - Dresden, Deutschland DA - 2013-01-29 PY - 2013 UR - http://www.ceqat-dghs.bam.de/en/events/index.htm AN - OPUS4-33474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -