TY - CONF A1 - Lu, Xin A1 - Hicke, Konstantin A1 - Krebber, Katerina T1 - Distributed fiber optic sensing for monitoring of underground facilities N2 - Distributed fiber optic sensing (DFOS) technique is a promising and robust non-destructive testing tool that can seamlessly acquire environmental conditions over large scales. Therefore, it has found extensive applications in structural health monitoring. Its appeal for monitoring underground facilities lies in the intrinsic properties of the optical fiber, such as immunity to magnetic interference, small size, chemical inertia, etc. This paper provides a concise overview of DFOS applications in underground facility monitoring. Following a brief introduction to the workingbnprinciple of the DFOS technique, various examples are provided to demonstrate how distributed fiber sensors contribute to monitoring underground facilities. The paper presents unpublished field test results with an emphasis in the energy sector, including monitoring gas storage facilities, geothermal reservoir exploration, and ground movement detection. Furthermore, the paper identifies several directions for enhancing the DFOS system. T2 - SPIE Photonics Europe CY - Strasbourg, France DA - 07.04.2024 KW - Structure health monitoring KW - Geothermal borehole KW - Distributed fiber optic sensing KW - Ground movement KW - Leakage detection PY - 2024 DO - https://doi.org/10.1117/12.3023571 SN - 0277-786X VL - 13001 SP - 1 EP - 10 PB - SPIE AN - OPUS4-60384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Huang, A1 - Zheng, A1 - Zhang, A1 - Lu, A1 - Wang, A1 - Kunte, Hans-Jörg A1 - Sand, W. T1 - Long Term Temperature and Humidity Evolution Forecast in Near Field of Nuclear Waste Container N2 - The paper aims to simulate the corrosion environment of nuclear waste containers at different geological disposal periods to obtain temperature and humidity information at the interface between the container and the surrounding environment. The simulated data and calculation results of long term temperature evolution at the surface of nuclear waste (HLW) containers from some typical nuclear countries about the safety disposition were reviewed. Combining different burial patterns, this paper speculated the long term temperature evolution rule for China. According to the study about saturation variation of buffer/backfill material at home and abroad, the humidity evolution of bentonite at the surface of HLW containers was specu- lated. The study showed that the temperature of the container surface increased rapidly at the beginning, and gradually decreased after the climax. For safety reasons, the maximum temperature was designed below 100°C. The saturation of bentonite was af- fected by the mutual influences of the heat released by nuclear waste decay and the infiltration of groundwater. It was dominated by the released heat in the early stage, and later was influenced greatly by the infiltration of groundwater. It is generally believed that the water content at the surface of the container will increase obviously in about 3 years, and will be saturated in about 10 years. The prediction of long-term temperature and humidity evolution will lay a foundation for study of corrosion evolution of nuclear waste containers in China. KW - Corrosion evolution KW - Nuclear waste KW - Disposal repository KW - Temperature and humidity PY - 2018 SN - 1672-9242 VL - 15 IS - 10 SP - 109 EP - 113 PB - Zhongguo Bingqi Gongye di-wujiu Yanjiusuo CY - Chongqing AN - OPUS4-46953 LA - zho AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Huang, Y.-L. A1 - Zheng, A1 - Zhang, A1 - Lu, A1 - Wang, A1 - Kunte, Hans-Jörg A1 - Sand, W. T1 - Forecast on Long Term Chemical Environment Evolution on Surface of Nuclear Waste Container N2 - Surface environment changes of nuclear waste container, mainly including oxygen contents, buffer pore water components and pH under the conditions of “borehole” type and “In-floor” type with bentonite buffer/backfill and concrete buffer were summarized. This summarization provides a basic corrosion environment reference for the corrosion evolution re- search of high-level radioactive waste disposal repository in our country. KW - Corrosion evolution KW - Nuclear waste KW - Disposal repository KW - Corrosion environment PY - 2018 DO - https://doi.org/10.7643/ issn.1672-9242.2018.10.017 SN - 1672-9242 VL - 15 IS - 10 SP - 103 EP - 108 PB - Zhongguo Bingqi Gongye di-wujiu Yanjiusuo CY - Chongqing AN - OPUS4-46952 LA - zho AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Christensen, J. B. A1 - Jørgensen, A. A. A1 - Vandborg, M. H. A1 - Thomas, P. J. A1 - Lu, Xin A1 - Failleau, G. A1 - Eisermann, R. A1 - Grüner-Nielsen, L. A1 - Balslev-Harder, D. A1 - Lassen, M. A1 - Krenek, S. T1 - Fiber-artefact methodology and calibration framework for Brillouin-based fiber sensing N2 - We propose, and demonstrate, the use of a fiber-optical measurement artefact as a metrological tool for traceable distance calibration of distributed optical fiber sensors. The constructed fiber artefact consists of a lead-in fiber coupled to a fiber loop using a 3-dB coupler and is used to calibrate both a home-build Brillouin-OTDR setup and a custom version of a commercial Brillouin-OTDR interrogator build for distributed temperature sensing. For both interrogators, we demonstrate distance calibrations with 1-meter uncertainty (k=1) in the offset length and 0.1 % (1 m/km) uncertainty (k = 1) in the distance scale factor. In addition, it is shown that the fiber artefact can be used to assess undesired distance-dependent measurement biases. KW - Distributed temperature sensing KW - Metrology KW - Distributed optical fiber sensing KW - Brillouin optical time-domain reflectrometry PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618853 DO - https://doi.org/10.1364/OE.544659 SN - 1094-4087 VL - 32 IS - 26 SP - 45483 EP - 45493 PB - Optica Publishing Group AN - OPUS4-61885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Progress review N2 - We report on the progress on calibration and characterization of distributed temperature sensing systems as a part of the European INFOTherm project. The most research results were achieved in the framework of the Work Package 2. T2 - Midterm meeting of INFOTherm project CY - Copenhagen, Denmark DA - 25.03.2025 KW - Humidity sensor KW - Optical fibre sensors KW - Distributed temperature sensing PY - 2025 AN - OPUS4-63007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lu, Xin A1 - Hicke, Konstantin A1 - Breithaupt, Mathias A1 - Strangfeld, Christoph T1 - Distributed Humidity Sensing in Concrete Based on Polymer Optical Fiber N2 - We present a preliminary investigation on distributed humidity monitoring during the drying process of concrete based on an embedded polymer optical fiber (POF). The water dissipated into the POF changes several properties of the fiber such as refractive index, scattering coefficient and attenuation factor, which eventually alters the Rayleigh backscattered light. The optical time Domain reflectometer (OTDR) technique is performed to acquire the backscattered signal at the wavelengths 650 nm and 500 nm, respectively. Experimental results show that the received signal increases at 650 nm while the fiber attenuation factor clearly increases at 500 nm, as the concrete dries out. In the hygroscopic range, the information retrieved from the signal change at 650 nm agrees well with the measurement result of the electrical humidity sensors also embedded in the concrete sample. KW - Distributed fiber optic sensing KW - Distributed humidity sensing KW - Polymer optical fibers KW - Concrete drying KW - Material moisture KW - Embedded humidity sensors PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-537644 DO - https://doi.org/10.3390/polym13213755 SN - 2073-4360 VL - 13 IS - 21 SP - 3755 PB - MDPI CY - Basel, Switzerland AN - OPUS4-53764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hu, W. A1 - Said, Samir A1 - Rohrmann, R. A1 - Teng, J. A1 - Li, Z. A1 - Lu, W. A1 - Cunha, A. T1 - Operational modal analysis and continuous dynamic monitoring of structures N2 - This paper addresses operational modal analysis (OMA) and continuous dynamic monitoring (CDM) of two bridges. One of them is installed with Tuned Mass Dampers (TMDs) while another one is a normal bridge. Two ambient vibration tests were performed on these two bridges respectively. It is observed that not only installation of TMDs but also environmental factors influence the variations of structural frequencies, which may mask the subtle change induced by small structural changes. As a result, continuous dynamic monitoring systems were implemented on these two bridges, in order to evaluate efficiency of the TMD system, remove the environmental effects and build reliable damage indices that are only sensitive to structural changes. The results of CDM of these two bridges during several years are presented. Software systems developed for OMA and CDM are also introduced. T2 - 14th International Symposium on Structural Engineering (ISSE-14) CY - Beijing, Peoples Republic of China DA - 12.10.2016 KW - Structure KW - Operational modal analysis KW - Continuous dynamic monitoring PY - 2016 SN - 978-7-03-050125-7 VL - 2016 SP - 366 EP - 372 PB - Science Press Beijing AN - OPUS4-38876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Qiu, Q. A1 - Noll, Matthias A1 - Abraham, W.-R. A1 - Lu, Y. A1 - Conrad, R. T1 - Applying stable isotope probing of phospholipid fatty acids and rRNA in a Chinese rice field to study activity and composition of the methanotrophic bacterial communities in situ N2 - Methanotrophs in the rhizosphere play an important role in global climate change since they attenuate methane emission from rice field ecosystems into the atmosphere. Most of the CH4 is emitted via transport through the plant gas vascular system. We used this transport for stable isotope probing (SIP) of the methanotrophs in the rhizosphere under field conditions and pulse-labelled rice plants in a Chinese rice field with CH4 (99% 13C) for 7 days. The rate of 13CH4 loss rate during 13C application was comparable to the CH4 oxidation rate measured by the difluoromethane inhibition technique. The methanotrophic communities on the roots and in the rhizospheric soil were analyzed by terminal-restriction fragment length polymorphism (T-RFLP), cloning and sequencing of the particulate methane monooxygenase (pmoA) gene. Populations of type I methanotrophs were larger than those of type II. Both methane oxidation rates and composition of methanotrophic communities suggested that there was little difference between urea-fertilized and unfertilized fields. SIP of phospholipid fatty acids (PLFA-SIP) and rRNA (RNA-SIP) were used to analyze the metabolically active methanotrophic community in rhizospheric soil. PLFA of type I compared with type II methanotrophs was labelled more strongly with 13C, reaching a maximum of 6.8 atom-% . T-RFLP analysis and cloning/sequencing of 16S rRNA genes showed that methanotrophs, especially of type I, were slightly enriched in the 'heavy' fractions. Our results indicate that CH4 oxidation in the rice rhizosphere under in situ conditions is mainly due to type I methanotrophs. KW - Methane-oxidizing bacteria KW - Rice field KW - Rhizosphere KW - Stable isotope probing KW - Phospholipid fatty acid KW - Particulate methane monooxygenase PY - 2008 DO - https://doi.org/10.1038/ismej.2008.34 SN - 1751-7362 SN - 1751-7370 IS - 2 SP - 602 EP - 614 PB - Nature Publishing Group CY - Basingstoke AN - OPUS4-17660 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lu, P. A1 - Lannutti, J.J. A1 - Klobes, Peter A1 - Meyer, Klaus T1 - X-ray Computed Tomography and Mercury Porosimetry for Evaluation of Density Evolution and Porosity Distribution N2 - X-ray computed tomography (CT) and mercury porosimetry were combined to connect density gradients and the distribution of open porosity in a sintered compact. CT clearly showed that open porosity follows the initial distribution of low-density zones. Mercury porosimetry detected three distinct levels of porosity. Microstructural examination correlated the porosity level with the coordination of (i) two to three or (ii) multiple grains around pores. This combination of techniques provides a novel tool for the study of pore and density-gradient evolution during sintering. PY - 2000 DO - https://doi.org/10.1111/j.1151-2916.2000.tb01227.x SN - 0002-7820 SN - 1551-2916 VL - 83 IS - 3 SP - 518 EP - 522 PB - Blackwell Publishing CY - Malden AN - OPUS4-11955 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bothe, Martin A1 - Mya, K.Y. A1 - Lin, E.M.J. A1 - Yeo, C. C. A1 - Lu, X. A1 - He, C. A1 - Pretsch, Thorsten T1 - Triple-shape properties of star-shaped POSS-polycaprolactone polyurethane networks N2 - Here, we present an investigation of the triple-shape properties of star-shaped polyhedral oligomeric silsesquioxane-poly(ε-caprolactone) polyurethanes (SPOSS-PUs), which have three-dimensional network structures. In a typical 'triple-shape functionalization process', mostly consisting of two tensile deformations at different temperatures, chain immobilization of the polymer network component poly(ε-caprolactone) (PCL) was successfully realized first through crystallization and then through vitrification. Subsequently, large parts of the respective strains were released under stress-free recovery conditions. The two-fold fixed ('programmed') specimens responded to heating with two independent length contractions (switching steps); the first shape change was associated with PCL devitrification and the second one with the melting of hitherto crystalline PCL. It was revealed that the triple-shape properties of SPOSS-PU networks considerably depend on PCL network chain length. When applying exactly the same 'triple-shape creation procedure', larger strain releases were detected in the first transition for polymers with a higher PCL network chain length, whereas the second transition was more accentuated for SPOSS-PU networks with a shorter PCL chain length. In the course of thermo-mechanical cycling, the formation of a neck during the second tensile deformation was repeatedly detected for SPOSS-PUs with higher PCL network chain length; in the subsequent recovery process the specimens even exhibited the highest total strain recoverability. Finally, gradual strain release could be achieved at temperatures below the PCL melting transition through the selection of up to four temperature holding steps, at which every time stable shapes were formed. KW - Shape memory polymer KW - Active polymer KW - Triple-shape polymer KW - Hybrid star-shaped polymer KW - POSS-polycaprolactone polyurethanes KW - Thermo-mechanical properties PY - 2012 DO - https://doi.org/10.1039/c1sm06474f SN - 1744-683X VL - 8 IS - 4 SP - 965 EP - 972 PB - RSC Publ. CY - Cambridge AN - OPUS4-25260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Humidity response analysis of optical fibers with hygroscopic coatings based on Lamé’s equations N2 - Optical fibers with hygroscopic coatings are widely used for humidity sensing, where the coating expands upon absorbing water, inducing strain in the fiber. This strain is then used to determine humidity. However, previous studies have oversimplified the strain generation process. A comprehensive three-dimensional model of the mechanical interaction between the coating and the fiber is built based on Lamé’s equations. An analytical expression for the induced strain is derived. The proposed model predicts larger humidity-induced strain compared to the reported ones, given the same Young’s modulus or coefficient of humidity expansion for the coating. Interestingly, the effect of coating thickness on strain response are quite similar for both methods. Experimental validation using fibers with a polyimide coating shows strong agreement with the theoretical predictions. T2 - 29th International Conference on Optical Fiber Sensors CY - Porto, Portugal DA - 26.05.2025 KW - Distributed fiber sensing KW - Humidity sensors KW - Lamé’s equations KW - Reflectometry KW - Optical fiber sensors KW - Rayleigh scattering KW - Structural health monitoring PY - 2025 AN - OPUS4-63261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Polarization diversity detection based wavelength scanning coherent optical time domain reflectometry N2 - Although wavelength scanning coherent optical time-domain reflectometry (WS-COTDR) system is immune to fading effect, it suffers from occasional and localized large errors caused by the false peak in the correlation spectrum due to the large signal generated in the random interference of the backscattered light. Polarization diversity detection is applied to a standard WS-COTDR system to suppress large measurement errors. In this way, the orthogonally polarized components of backscattered light can be obtained and processed separately. Due to the birefringence of the sensing fiber, the components experience different interference processes, so the average of their correlation spectrum can suppress the false peaks and finally reduce the occurrence of larger errors. The effectiveness of the proposed method is validated in laboratory for monitoring of sinusoidal vibrations and in field for tracking the bus movement via a dark fiber. T2 - 29th International Conference on Optical Fiber Sensors CY - Porto, Portugal DA - 26.05.2025 KW - Coherent optical time domain reflectometry KW - Traffic monitoring KW - Polarization diversity detection KW - Distributed fiber sensing PY - 2025 AN - OPUS4-63260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Großwig, S. A1 - Weber, U. A1 - Krebber, Katerina T1 - Monitoring acoustic events in boreholes using wavelengthscanning coherent optical time domain reflectometry in multimode fiber N2 - A distributed acoustic sensor (DAS) based on wavelength-scanning coherent optical time domain reflectometer (WS-COTDR) is tested in an underground gas storage based on a multimode fiber for the first time to the best of our knowledge. The WS-COTDR acquires the reflection spectrum by scanning the wavelength of the laser and uses the spectra to calibrate strain. It overcomes the fading problem which is common for all DAS systems, and possesses the advantage of simple configuration and low-cost. The working principle of the system is well explained and the measurement results are presented. Various artificial and natural acoustic events have been successfully detected by the WS-COTDR. Such a sensor demonstrates several advantages over the traditional DAS systems, so it is supposed to be widely used in the oil and gas industry. T2 - EAGE GeoTech 2021 Second EAGE Workshop on Distributed Fibre Optic Sensing CY - Online meeting DA - 01.03.2021 KW - Leakage detection KW - Distributed acoustic sensing KW - Distributed fiber optic sensing PY - 2021 DO - https://doi.org/10.3997/2214-4609.202131010 SP - Paper 10, 1 PB - European Association of Geoscientists & Engineers CY - Houten, Niederlande AN - OPUS4-52248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Großwig, S. A1 - Weber, U. A1 - Krebber, Katerina T1 - Monitoring acoustic events in boreholes using wavelengthscanning coherent optical time domain reflectometry in multimode fiber N2 - A distributed acoustic sensor (DAS) based on wavelength-scanning coherent optical time domain reflectometer (WS-COTDR) is tested in an underground gas storage based on a multimode fiber for the first time to the best of our knowledge. The WS-COTDR acquires the reflection spectrum by scanning the wavelength of the laser and uses the spectra to calibrate strain. It overcomes the fading problem which is common for all DAS systems, and possesses the advantage of simple configuration and low-cost. The working principle of the system is well explained and the measurement results are presented. Various artificial and natural acoustic events have been successfully detected by the WS-COTDR. Such a sensor demonstrates several advantages over the traditional DAS systems, so it is supposed to be widely used in the oil and gas industry. T2 - EAGE GeoTech 2021 CY - Online meeting DA - 01.03.2021 KW - Borehole monitoring KW - Distributed fiber sensing KW - Acoustic sensing PY - 2021 DO - https://doi.org/10.3997/2214-4609.202131010 SP - 1 EP - 5 AN - OPUS4-52152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krebber, Katerina A1 - Weege, S. A1 - Großwig, S. A1 - Obermöller, M. A1 - Perk, M. A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weber, U. A1 - Pfeiffer, T. A1 - Rembe, M. T1 - Kombinierte faseroptische Messungen in Bohrlöchern helfen bei der Detektion von Kleinstleckagen N2 - Seit November 2019 läuft ein breit angelegtes und vom BMWi gefördertes ZIM-Kooperationsprojekt zwischen der Bundesanstalt für Materialforschung und -prüfung (BAM), der IAB'Weimar gGmbH, der GKSO GmbH & Co. Projekt KG, der DEEP.KBB GmbH sowie der Rembe Consulting PartG mbB. Ziel des Forschungsvorhabens sind sowohl die Lokalisierung als auch die Quantifizierung insbesondere sehr kleiner Leckagen in einer Bohrlochverrohrung durch die Nutzung faseroptischer Messtechnik. Durch Messdatenkopplung und den Wegfall bewegungsbedingter Nachteile einer Messsonde werden wesentlich präzisere Ergebnisse zur Bewertung der Bohrlochintegrität als üblich erwartet. T2 - DGMK/ÖGEW-Frühjahrstagung 2020 CY - Meeting was canceled DA - 15.04.2020 KW - Wasserstoffspeicher KW - Kavernenspeicher KW - Verteilte faseroptische akustische Sensorik PY - 2020 VL - 6 SP - 43 EP - 43 PB - DVV Media Group CY - Hamburg AN - OPUS4-52233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Krebber, Katerina T1 - Characterizing vibration response of fiber cables for distributed acoustic sensing N2 - The vibration responses of two fiber cables are characterized up to 16 kHz and compared with a standard tight-buffered 900 um fiber. The response of the cables is suppressed due to the cable protection. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Distributed fiber sensing KW - Acoustic sensing KW - Response characterization PY - 2022 AN - OPUS4-56099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weege, S. A1 - Roske, T. A1 - Krebber, Katerina T1 - Leakage detection at a borehole simulator using distributed acoustic sensing N2 - A distributed acoustic sensing system is used to detect the leakage in a borehole simulator by measuring the leakage induced vibration. The leakage location can be clearly determined by frequency spectrum analysis. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Leakage detection KW - Structural health monitoring KW - Distributed fiber sensing KW - Distributed acoustic sensing PY - 2022 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-56097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Krebber, Katerina T1 - Characterizing vibration response of fiber cables for distributed acoustic sensing N2 - The vibration responses of two fiber cables are characterized up to 16 kHz and compared with a standard tight-buffered 900 um fiber. The response of the cables is suppressed due to the cable protection T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Response characterization KW - Distributed fiber sensing KW - Acoustic sensing PY - 2022 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-56096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weege, S. A1 - Roske, T. A1 - Krebber, Katerina T1 - Leakage detection at a borehole simulator using distributed acoustic sensing N2 - A distributed acoustic sensing system is used to detect the leakage in a borehole simulator by measuring the leakage induced vibration. The leakage location can be clearly determined by frequency spectrum analysis. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Structural health monitoring KW - Distributed fiber sensing KW - Distributed acoustic sensing KW - Leakage detection PY - 2022 AN - OPUS4-56098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, Kun A1 - Lu, Xin A1 - Schukar, Marcus A1 - Hicke, Konstantin T1 - Water absorption effects on distributed temperature sensing using polyimide-coated optical fiber N2 - Polyimide-coated fibers are becoming more popular for distributed temperature sensing (DTS) because this coating can withstand much higher temperatures than the standard acrylate coating. As a hygroscopic material, polyimide can absorb water from the air, changing its properties, which may result in a modified temperature response of the sensing fiber. This study investigates the effect of water absorption on the performance of polyimide-coated optical fibers with different sizes and properties. The thermal response of these fibers was determined experimentally from 20°C to 90°C at a broad relative humidity level ranging from 10% to 90%. The results show that all the fibers experienced a decrease in temperature sensitivity as humidity increased, with the most noticeable non-linear spectral shift observed at higher humidity levels. These findings highlight the importance of optimizing fiber design and coating properties to balance stability and sensitivity, ensuring the reliable performance of DTS systems under extreme environmental conditions. T2 - 29th International Conference on Optical Fiber Sensors CY - Porto, Portugal DA - 26.05.2025 KW - Humidity sensing KW - Distributed temperature sensing KW - Optical fiber sensors KW - Temperature sensing KW - Water absorption KW - Polyimide-coated fiber PY - 2025 SN - 978-1-5106-9187-2 DO - https://doi.org/10.1117/12.3062748 VL - 13639 SP - 136393W-1 EP - 136393W-4 PB - SPIE AN - OPUS4-63642 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus T1 - Humidity response analysis of optical fibers with hygroscopic coatings based on Lamé’s equations N2 - Optical fibers with hygroscopic coatings are widely used for humidity sensing, where the coating expands upon absorbing water, inducing strain in the fiber. This strain is then used to determine humidity. However, previous studies have oversimplified the strain generation process. A comprehensive three-dimensional model of the mechanical interaction between the coating and the fiber is built based on Lamé’s equations. An analytical expression for the induced strain is derived. The proposed model predicts larger humidity-induced strain compared to the reported ones, given the same Young’s modulus or coefficient of humidity expansion for the coating. Interestingly, the effect of coating thickness on strain response are quite similar for both methods. Experimental validation using fibers with a polyimide coating shows strong agreement with the theoretical predictions. T2 - 29th International Conference on Optical Fiber Sensors CY - Porto, Portugal DA - 26.05.2025 KW - Reflectometry KW - Distributed fiber sensing KW - Humidity sensors KW - Lamé’s equations KW - Optical fiber sensors KW - Structural health monitoring KW - Rayleigh scattering PY - 2025 SN - 978-1-5106-9188-9 DO - https://doi.org/10.1117/12.3060891 VL - 13639 SP - 1 EP - 4 PB - SPIE AN - OPUS4-63257 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -