TY - CONF A1 - Ramos, Inês I. A1 - Carl, Peter A1 - Schneider, Rudolf A1 - Segundo, Marcela A. T1 - Development of automated immunosensing methods for clinical and environmental Analysis using lab-on-valve platforms N2 - The lab-on-valve (LOV) is a mesofluidic platform that has been recently exploited for the automation and miniaturization of bioanalytical assays, resorting namely to molecular recognition schemes based on immunosensing. Due to its high versatility for reagent accommodation, it is possible to establish immunoassays under several formats (eg. direct competitive ELISA, sandwich ELISA or even label-free immunoaffinity chromatography). For instance, the LOV has been used as a manifold for UV-vis micro-Bead Injection Spectroscopy (μ-BIS), a technique that involves the quantification of the target analyte by direct measurement on the surface of a solid phase capable of retaining the target analyte by molecular recognition. The μ-BIS-LOV strategy affords several analytical advantages, namely short time-toresult intervals (3 to 15 min), low sample volume (1-20 μL), automated solution handling and washing steps, downscaling of reagents’ consumption, low-cost analysis and little generation of waste. Additionally, the solid support is renewed before each determination, minimizing surface fouling, cross-contamination issues and functional group deactivation. No sample clean-up steps are required because interferences are separated from the target analyte upon quantification mediated by a molecular recognition element attached to the micro-bead column. The portability of the LOV device makes it compatible with point-of-care testing. To our knowledge, this technique has been mainly employed for the evaluation and optimization of bioaffinity processes, but its potential for clinical and environmental analysis remains underexploited. Hence, in this communication, different immunosensing strategies using the LOV platform will be addressed, namely the determination of autoimmune IgG in human serum, and the assessment of drug (carbamazepine) levels in wastewater samples. T2 - EBS 2017 CY - Potsdam, Germany DA - 20.03.2017 KW - Lab-on-valve KW - Automation KW - Immunoassay PY - 2017 AN - OPUS4-39521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dippong, Martin A1 - Carl, Peter A1 - Lenz, C. A1 - Schenk, J. A. A1 - Hoffmann, Katrin A1 - Schwaar, Timm A1 - Schneider, Rudolf A1 - Kuhne, Maren T1 - Hapten-specific single-cell selection of hybridoma clones by fluorescence-activated cell sorting for the generation of monoclonal antibodies N2 - The conventional hybridoma screening and subcloning process is generally considered to be one of the most critical steps in hapten-specific antibody production. It is time-consuming, monoclonality is not guaranteed, and the number of clones that can be screened is limited. Our approach employs a novel hapten-specific labeling technique of hybridoma cells. This allows for fluorescence-activated cell sorting (FACS) and single-cell deposition and thereby eliminates the above-mentioned problems. A two-step staining approach is used to detect antigen specificity and antibody expression: in order to detect antigen specificity, hybridoma cells are incubated with a hapten−horseradish peroxidase conjugate (hapten−HRP), which is subsequently incubated with a fluorophore-labeled polyclonal anti-peroxidase antibody (anti-HRP−Alexa Fluor 488). To characterize the expression of membrane-bound immunoglobulin G (IgG), a fluorophore-labeled anti-mouse IgG antibody (anti-IgG−Alexa Fluor 647) is used. Hundreds of labeled hybridoma cells producing monoclonal antibodies (mAbs) specific for a hapten were rapidly isolated and deposited from a fusion mixture as single-cell clones via FACS. Enzyme-linked immunosorbent assay (ELISA) measurements of the supernatants of the sorted hybridoma clones revealed that all hapten-specific hybridoma clones secrete antibodies against the target. There are significant improvements using this high-throughput technique for the generation of mAbs including increased yield of antibody-producing hybridoma clones, ensured monoclonality of sorted cells, and reduced development times. KW - Monoclonal antibodies KW - FACS KW - Hybridoma cells PY - 2017 DO - https://doi.org/10.1021/acs.analchem.6b04569 SN - 0003-2700 SN - 1520-6882 VL - 89 IS - 7 SP - 4007 EP - 4012 PB - ACS Publications AN - OPUS4-40320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Robens, E. A1 - Klobes, Peter A1 - Balköse, Gulsum Devrim A1 - Amarasiri, S. A1 - Jayaweera, A. T1 - On the terms mass and weight N2 - A short survey is given on mass units and recommendations on the proper use of the notations mass and weight.Whereas mass is an inertial physical quantity in classical mechanics, weight is a force due to the gravitational field and depending on the geographic situation. KW - Atomic mass KW - Electron volt KW - Mass KW - Relative KW - Specific KW - Weight PY - 2008 DO - https://doi.org/10.1007/s10973-008-9353-z SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 94 IS - 3 SP - 619 EP - 622 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-18834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz-Forberg, Bernd A1 - Zeisler, Peter A1 - Droste, Bernhard A1 - Kondratiev, A. A1 - Kozlov, J. A1 - Tichinov, N. T1 - Soviet-German cooperation in safety improvements of spent fuel transport casks N2 - The paper gives a survey of the Soviet (Russian) -German activities which started in 1988 with the objective of creating a long-term scientific-technical cooperation in the field of transport and storage casks for spent nuclear fuel. The first step, i.e., the step of informing each other about the state of development is done. The more complicated second phase with concerted common activities of both the Russian and German competent authorities and industrial enterprises is intended to start in the near future. T2 - PATRAM ´92 - 10th International symposium on the packaging and transportation of radioactive materials CY - Yokohama, Japan DA - 1992-09-13 PY - 1992 VL - 1 SP - 343 EP - 350 AN - OPUS4-21824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sonsino, C.M. A1 - Kaufmann, H. A1 - Masendorf, R. A1 - Hatscher, A. A1 - Zenner, H. A1 - Bork, Claus-Peter A1 - Hinterdorfer, J. A1 - Sonne, H.M. A1 - Engl, B. A1 - Steinbeck, G. T1 - Werkstoffkennwerte für die Lebensdauerberechnung von Strukturen aus Stahlfeinblechen für den Automobilbau N2 - Im Rahmen eines gemeinschaftlichen Projektes der Stahl- und Automobilindustrie wurden für 17 Stahlfeinbleche des Automobilbaus in verschiedenen Anlieferungs- und Verformungszuständen unter -40°C, Raumtemperatur und +100°C mit 37 Versuchsreihen Anrisswöhlerlinien und zügige bzw. zyklische Spannung-Dehnung-Kurven bestimmt. Sämtliche Versuchspunkte, Hysteresen und ermittelte zyklische Kennwerte liegen in einer Datenbank vor. Eine Korrelationen zwischen den Kennwerten aus dem Zugversuch und den Kennwerten aus den zyklischen, dehnungsgeregelten Versuchen ist grundsätzlich möglich. KW - Zyklische Werkstoffkennwerte KW - Zügige und zyklische Spannung-Dehnung-Kurve KW - Dehnungswöhlerlinie KW - Technischer Anriss KW - Elasto-plastisches Werkstoffverhalten KW - Automobilbau KW - Cyclic properties KW - Monotonic and cyclic stress-strain curve KW - Strain-life curve KW - Technical crack KW - Elasto-plastic material behaviour KW - Thin steel sheets KW - Automotive engineering KW - Karosseriestähle KW - Strukturen KW - Lebensdauerberechnung KW - Zyklische Kennwerte PY - 2004 DO - https://doi.org/10.1002/mawe.200400769 SN - 0933-5137 SN - 1521-4052 VL - 35 IS - 8 SP - 522 EP - 533 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-22436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Steinbeck, G. A1 - Bleck, W. A1 - Bork, Claus-Peter A1 - Evertz, T. A1 - Frehn, A. A1 - Masendorf, R. A1 - Sonsino, C.M. ED - Palkowski, H. T1 - Ermittlung von Berechnungskennwerten an Karosseriestählen - Bericht über ein Gemeinschaftsprojekt der Stahl- und Automobilindustrie T2 - 4. Industriekolloquium - SFB 362 Fertigen in Feinblech - Werkstoffe Verfahren Konzepte CY - Bad Harzburg, Deutschland DA - 2004-02-11 KW - Karosseriestähle KW - Berechnung KW - Kennwerte PY - 2004 SN - 3937057056 VL - 1 IS - 2 SP - 127 EP - 136 PB - GRIPS media AN - OPUS4-22600 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beke, S. A1 - Sugioka, K. A1 - Midorikawa, K. A1 - Péter, Á. A1 - Nánai, L. A1 - Bonse, Jörn T1 - Characterization of the ablation of TeO2 crystals in air with femtosecond laser pulses N2 - Femtosecond (fs) laser pulse ablation (pulse duration of 150 fs, wavelength of 775 nm, repetition rate of 1 kHz) of single-crystalline TeO2 surfaces was performed in air using the direct focusing technique. The lateral and vertical dimensions of laser ablated craters as well as the laser damage thresholds were evaluated for different pulse numbers applied to the same spot. The joint observation using optical microscopy, atomic force microscopy and scanning electron microscopy revealed the surface morphology of the ablated craters and also showed that the ablation threshold depends significantly on the number of laser pulses applied to the same spot due to incubation effects. The incubation effects change the absorption processes involved in fs-laser ablation of the transparent material from multiphoton absorption to a single-photon absorption. These results are discussed on the basis of recent models of the interaction of fs-laser pulses with dielectrics. KW - Femtosecond laser ablation KW - Damage threshold KW - TeO2 KW - Dielectrics PY - 2010 DO - https://doi.org/10.1088/0022-3727/43/2/025401 SN - 0022-3727 SN - 1361-6463 VL - 43 IS - 2 SP - 025401-1 - 025401-6 PB - IOP Publ. CY - Bristol AN - OPUS4-20665 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hesselbach, J. A1 - Herrmann, C. A1 - Bock, R. A1 - Dettmer, T. A1 - Kley, Gerd A1 - Köcher, Peter A1 - Brenneis, Rudolf A1 - Meyer-Pittroff, R. A1 - Falk, O. A1 - Hansen, A. T1 - Kühlschmierstoffe aus technischen tierischen Fetten und Altspeisefetten - Herstellung, Technologie und Ökobilanzierung KW - Enzymatische Alkoholyse KW - Tierfett KW - Altspeisefett KW - Kühlschmierstoff KW - Umesterung KW - Produktökobilanz KW - LCA PY - 2003 SN - 1435-5272 VL - 9 IS - Sonderheft `Biokatalyse´ SP - 24 EP - 27 PB - BIOCOM CY - Berlin AN - OPUS4-2684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Gaal, Mate A1 - Müller, Christina A1 - Rosenthal, Martina A1 - Ewert, Uwe A1 - Lewis, A. A1 - Bloodworth, T. A1 - Wilrich, Peter-Th. A1 - Guelle, D. T1 - ITEP project 2.1.1.2 - Final report - Reliability model for test and evaluation of metal detectors N2 - Metal detectors used in demining have been tested within the frame of the International Test and Evaluation Programme project ITEP 2.1.1.2. Detection reliability tests were performed in accordance with the CEN workshop agreement describing specifications for test and evaluation (CWA 14747:2003). Results of these tests are aimed to verify and should help to optimise the proposed testing procedures. KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2004 UR - http://www.itep.ws/pdf/Itep_no2.1.1.2_reliability_model.pdf N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. SP - 1 EP - 51 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-6049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Gaal, Mate A1 - Rosenthal, Martina A1 - Bär, Sylke A1 - Lewis, A. A1 - Bloodworth, T. A1 - Guelle, D. A1 - Wilrich, Peter-Th. T1 - ITEP-Test Trials for Detection Reliability Assessment of Metal Detectors N2 - The total reliability of a mine searching system is driven by the triple of intrinsic capability, which describes the physical-technical basis capability, the application and environmental factors and the human factors. Some of them can be determined in laboratory measurements but the human factor and a part of environment conditions and their interaction with the device need to be treated statistically. That is why the test & evaluation procedure described in CEN CWA 14747:2003, includes in addition to parameter tests of metal detectors also the reliability or blind field tests under local conditions with local personnel. A series of three big field trials had been accomplished in the ITEP-project 2.1.1.2 “Reliability Model for Test & Evaluation of Metal Detectors” to specify the optimum conditions for reliable trial results with affordable effort. For each set of specific working conditions, characterized in terms of a combination of one mine type in one soil with one detector handled by local personnel, the searching system will show up a working performance in mine detection rates as a function of mine depth and show up a certain overall false call rate. During the ITEP-trials in Benkovac and Oberjettenberg the authors learnt to determine this function separately for each mine type in each soil, which is especially important for low metal mines in uncooperative soil which will be illustrated for the mine PMA2 in different types of soil. The question of representativeness for field conditions on the one hand and necessary statistical set up for the possibility to distinguish between individual detector performances is still under discussion. KW - Zuverlässigkeit der Minensuche KW - Feldtests KW - Modulares Modell KW - Metalldetektor PY - 2005 UR - http://maic.jmu.edu/journal/8.2/rd/mueller.htm SN - 1533-9440 SN - 1533-6905 N1 - Geburtsname von Rosenthal, Martina: Scharmach, M. - Birth name of Rosenthal, Martina: Scharmach, M. IS - 8.2 SP - 86 EP - 90 CY - Harrisonburg AN - OPUS4-6041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bleck, W. A1 - Bork, Claus-Peter A1 - Evertz, Th. A1 - Frehn, A. A1 - Masendorf, R. A1 - Sonsino, C.M. A1 - Steinbeck, G. T1 - Ermittlung von Berechnungskennwerten an Karosseriestählen N2 - In einem Gemeinschaftsprojekt der Stahl- und Automobilindustrie wurden an zwanzig Stählen für Feinblech elastische, plastische und zyklische Kennwerte für die FE-Simulation ermittelt. Die Untersuchungen mit dem Ziel, Eingabekennwerte für FE-Berechnungen zu erhalten, erbrachten einen erheblichen Erfahrungszuwachs im Bereich der Messtechnik sowie der Datenerfassung und -weiterverarbeitung. Der vorliegende Beitrag gibt einen Überblick über die Untersuchung und ihre Ergebnisse. KW - Feinblech Stähle KW - Kennwerte für die FEM-Simulation KW - Elastisch KW - Plastisch KW - Zyklisch KW - Standardisierte Kennwertermittlung KW - Rechnerisch PY - 2005 SN - 0001-2785 VL - 107 IS - 5 SP - 436 EP - 447 PB - Vieweg CY - Wiesbaden AN - OPUS4-10654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spickermann, J. A1 - Martin, K. A1 - Räder, H.J. A1 - Müllen, K. A1 - Schlaad, H. A1 - Müller, A. H. E. A1 - Krüger, Ralph-Peter T1 - Quantitative analysis of broad molecular weight distributions obtained by MALDI-TOF mass spectrometry PY - 1996 SN - 1469-0667 SN - 1356-1049 SN - 1365-0718 IS - 2 SP - 161 EP - 165 PB - IM Publications CY - Chichester AN - OPUS4-2153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlaad, H. A1 - Müller, A. H. E. A1 - Kolshorn, H. A1 - Krüger, Ralph-Peter T1 - Mechanism of anionic polymerization of (meth)acrylates in the presence of aluminium alkyls PY - 1995 SN - 0170-0839 SN - 1436-2449 VL - 35 SP - 169 EP - 176 PB - Springer CY - Berlin AN - OPUS4-2144 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -