TY - JOUR A1 - Su, H. A1 - Wu, Chuan Song A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Thermal energy generation and distribution in friction stir welding of aluminum alloys N2 - The accurate prediction of the thermal energy generation and distribution in friction stir welding process is of great significance for the optimization of the process parameters and the understanding of the underlying mechanisms. In this study, a new method of integrative calculation and measurement is proposed to obtain the more reasonable values of the frictional coefficient and the slip rate, which are both used to characterize the heat generation rate at the tool-workpiece contact interfaces. A three-dimensional model is established to fully couple the energy generation, heat transfer and material flow in friction stir welding of aluminum alloys. The energy produced by both interfacial friction and plastic deformation are taken into consideration. The analysis accuracy of the thermal energy generation and distribution is improved, and the distribution features of thermal energy density in the vicinity of the tool are elucidated. The predicted peak temperature values at some locations are in agreement with the experimentally measured ones. KW - Thermal energy generation KW - Energy density distribution KW - Heat transfer KW - Material flow KW - Friction stir welding PY - 2014 U6 - https://doi.org/10.1016/j.energy.2014.09.045 SN - 0360-5442 VL - 77 SP - 720 EP - 731 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-32076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Su, H. A1 - Wu, Chuan Song A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Simultaneous measurement of tool torque, traverse force and axial force in friction stir welding N2 - Simultaneous measurement of the tool torque, traverse force and axial force during friction stir welding process is of great significance to the understanding of the underlying process mechanism and the optimizing of the process parameters. Different from the traditional measurement methods using load cell or rotating component dynamometer, an indirect but economical methodology is used in this study for the simultaneous measurement of the traverse force, axial force and tool torque by monitoring the output torques of the servo motors and main spindle three-phase AC induction motor inside the FSW machine. The values of the traverse force, axial force and tool torque are determined under different welding conditions, and the influencing factors are examined. The measured results in friction stir welding of AA2024-T4 aluminum alloys at different combinations of tool rotation speed and welding speed lay foundation for process optimization. KW - Friction stir welding KW - Measurement KW - Traverse force KW - Axial force KW - Tool torque PY - 2013 U6 - https://doi.org/10.1016/j.jmapro.2013.09.001 SN - 0278-6125 SN - 1526-6125 VL - 15 IS - 4 SP - 495 EP - 500 PB - Elsevier Ltd. CY - Dearborn, Mich., USA AN - OPUS4-29688 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bachmann, Marcel A1 - Rethmeier, Michael A1 - Wu, Chuan Song T1 - Sensitivity analysis of the residual stress state in friction stir welding of high strength aluminium alloy N2 - In this paper, the friction stir welding process was numerically investigated for 6 mm thick aluminum alloy AA2024-T3. The finite element software COMSOL Multiphysics was used to calculate the transient thermal field during welding and the mechanical reaction depending on different mechanical clamping conditions and hardening models subsequently. A thermal pseudo-mechanical (TPM) heat source was implemented. Softening effects of the material due to precipitation hardening dissolution caused by the frictional heat were accounted for. The transient temperature evolution measured by thermocouple elements at various locations was compared to the numerical results. A good agreement was found for the thermal field. A sensitivity study of the mechanical models showed the strong influence of the clamping conditions and the softening model. PY - 2016 U6 - https://doi.org/10.3139/120.110809 SN - 0025-5300 VL - 58 IS - 1 SP - 20 EP - 26 PB - Hanser CY - München AN - OPUS4-35269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chen, Ji A1 - Schwenk, Christopher A1 - Wu, Chuan Song A1 - Rethmeier, Michael T1 - Prediction of weld pool shape and influence of joint preparation angle for new gas metal arc welding processes N2 - This article studies the three dimensional transient weld pool dynamics and the influence of joint preparation angle on welding of low carbon structural steel plates using the ForceArc® process. ForceArc is a new gas metal arc welding technology which allows adequate fusion and penetration with a smaller V groove angle. This enhances welding efficiency significantly because of reduction of layers and low material consumption. The deformation of the weld bead is calculated with an accurate coupling of the heat transfer with fluid flow through continuity, momentum and the energy equations combined with the effect of droplet impingement, gravity, electromagnetic force, buoyancy, drag forces and surface tension force (Marangoni effect). Four different angles of V groove are employed with the same welding parameters and their influence on the weld pool behavior and weld bead geometry is calculated and analyzed, to allow subsequent calculations of residual stress and distortion of the workpiece. Such a simulation is an effective way to study welding processes because the influence of all the welding parameters can be analyzed separately with respect to thermal cycle, weld bead formation, and the microstructure of the weld. Good agreement is shown between the predicted and experimentally determined weld bead dimensions. It was found that with a larger groove angle, the penetration depth increases. Furthermore, a higher wire feeding rate is needed to fill the larger groove. The model presented can be used for further analyses of GMAW processes as well as input data for the numerical calculation of welding induced residual stresses and distortions using Computational Weld Mechanics CWM. T2 - JOM-16 - 16th International Conference on the Joining of Materials CY - Tisvildeleje, Denmark DA - 10.05.2011 KW - Numerical simulation KW - Gas metal arc welding KW - Weld pool shape KW - Fluid flow KW - V groove PY - 2011 SN - 87-89582-19-5 IS - JOM 7 / J15 SP - 1 EP - 13 AN - OPUS4-23984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chen, Ji A1 - Schwenk, Christopher A1 - Wu, Chuan Song A1 - Rethmeier, Michael T1 - Predicting the influence of groove angle on heat transfer and fluid flow for new gas metal arc welding processes N2 - This article studies the three dimensional transient weld pool dynamics and the influence of groove angle on welding of low carbon structural steel plates using the ForceArc® process. The deformation of the weld bead is also calculated with an accurate coupling of the heat transfer with fluid flow through continuity, momentum and the energy equations combined with the effect of droplet impingement, gravity, electromagnetic force, buoyancy, drag forces and surface tension force (Marangoni effect). Different angles of V groove are employed under the same welding parameters and their influence on the weld pool behavior and weld bead geometry is calculated and analyzed, which is needed for subsequent calculations of residual stress and distortion of the workpiece. Such a simulation is an effective way to study welding processes because the influence of all welding parameters can be analyzed separately with respect to heat transfer, weld pool dynamic, and microstructure of the weld. Good agreement is found between the predicted and experimentally determined weld bead cross-section and temperature cycles. It is found that the main flow pattern is more or less the same although the groove angle increases, but it will evoke larger amount of fluid to flow downward to get deeper penetration. KW - Numerical simulation KW - Gas metal arc welding KW - Weld pool dynamics KW - Fluid flow KW - V groove PY - 2012 U6 - https://doi.org/10.1016/j.ijheatmasstransfer.2011.08.046 SN - 0017-9310 VL - 55 IS - 1-3 SP - 102 EP - 111 PB - Elsevier CY - Amsterdam AN - OPUS4-26001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Su, H. A1 - Wu, Chuan Song A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Numerical modeling for the effect of pin profiles on thermal and material flow characteristics in friction stir welding N2 - Understanding the influence of tool/pin shapes on the thermal and material flow behaviors in friction stir welding is of great significance for the optimal design of tool/pin based on a scientific principle. In this study, a numerical method based on computational fluid dynamics is employed to quantitatively analyze the thermo-physical phenomena in friction stir welding with two tools of different pin shapes (axisymmetrical conical tool and asymmetrical triflat tool). Through combining a steady state model with a transient state model, both the computation efficiency and accuracy are ensured. The boundary conditions of heat transfer and material flow are determined with considering a partial sticking/sliding contact condition at the tool–workpiece interface. The total heat generation, heat density and temperature distribution during the welding process with triflat tool are elucidated and compared with that of conical tool, and the material flow patterns and deformation regions of various pin orientations are illustrated in detail. It is found that the deformation zone caused by triflat tool is larger than that by conical tool, which is validated by the weld macrographs. The computed thermal cycles and peak temperature values at some locations are in good agreement with the experimentally measured ones. KW - Friction stir welding KW - Pin profile KW - Heat generation KW - Material flow KW - Modeling PY - 2015 U6 - https://doi.org/10.1016/j.matdes.2015.04.012 SN - 0261-3069 SN - 0264-1275 VL - 77 SP - 114 EP - 125 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-33031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liu, X. C. A1 - Wu, Chuan Song A1 - Rethmeier, Michael A1 - Pittner, Andreas T1 - Mechanical properties of 2024-T4 aluminium alloy joints in ultrasonic vibration enhanced friction stir welding N2 - Ultrasonic vibration enhanced friction stir welding (UVeFSW) is a recent modification of conventional friction stir welding (FSW), which transmits ultrasonic vibration directly into the localized area of the workpiece near and ahead of the rotating tool. In this study, a high strength aluminium alloy (2024-T4) was welded by this process and conventional FSW, respectively. Then tensile tests, microhardness tests and fracture surface analysis were performed successively on the welding samples. The tests results reveal that ultrasonic vibration can improve the tensile strength and the elongation of welded joints. The microhardness of the stir zone also increases. KW - Ultrasonic vibration KW - Friction stir welding KW - Mechanical properties PY - 2013 UR - https://www.researchgate.net/publication/286735810_Mechanical_properties_of_2024-T4_aluminium_alloy_joints_in_ultrasonic_vibration_enhanced_friction_stir_welding VL - 22 IS - 4 SP - 8 EP - 13 AN - OPUS4-40773 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -