TY - CONF A1 - Baer, Wolfram A1 - Müller, Karsten A1 - Wossidlo, Peter A1 - Klingbeil, Dietmar T1 - Dynamic fracture toughness behaviour of ductile cast iron with respect to structural integrity assessment N2 - Modern structural integrity assessment procedures in the field of nuclear related technology incorporate fracture mechanical concepts. Therefore, they inevitably require the availability of both, loading parameters as well as material characteristics in terms of fracture mechanical quantities. Especially in case of dynamic loading conditions, the methods for the determination of the loading parameters need further improvement and there is a lack of material characteristics as well. In Germany, ductile cast iron (DCI) is used for heavy-sectioned casks for radioactive materials. New developments in cask design and efforts to extend the application limits require further investigations. The present study is part of an ongoing fracture mechanics research programme of BAM which is focused on the systematic mechanical and fracture mechanical material characterisation of DCI materials under dynamic loading conditions. In this study, results of fracture mechanics investigations on ductile cast iron from an original DCI container with a wide variety of microstructure under dynamic loading conditions in the temperature range from -50 °C to +22 °C are presented. Large scale as well as small scale single edge crack bend specimens SE(B) with thicknesses of 140 mm and 15 mm, respectively were tested. Furthermore, it is reported on the results of a finite element simulation of the dynamic large scale fracture mechanics tests. Strength and deformation characteristics were determined in dynamic tensile tests. They are discussed with respect to the influence of pearlite content and test temperature. The material specific experimental difficulties in the determination of reliable dynamic crack initiation toughness values of DCI are outlined. T2 - 17th International Conference on Structural Mechanics in Reactor Technology ; SMiRT 17 CY - Prague, Czech Republic DA - 2003-08-17 KW - Dynamic fracture toughness KW - Ductile cast iron KW - Structural integrity KW - Component KW - Specimen geometry KW - Testing KW - Loading rate KW - Test temperature KW - Microstructure KW - Graphite morphology KW - Crack initiation toughness KW - Analysis procedure KW - Finite element simulation KW - Fracture mechanics PY - 2003 IS - G04-4 SP - 1 EP - 8 CY - Prague AN - OPUS4-2856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Karsten A1 - Wossidlo, Peter A1 - Baer, Wolfram ED - Dlouhý, I. T1 - Fracture toughness behaviour of thick-walled nodular cast iron at elevated loading rates T2 - NATO Final Project Workshop on Fracture Resistance of Steels for Containers of Spent Nuclear Fuel ; NATO Final Project Workshop on Transferability of Fracture Mechanical Data CY - Brno, Czech Republic DA - 2001-11-05 KW - Ductile cast iron KW - Fracture mechanics KW - Specimen size effect KW - Loading rate effect PY - 2002 SN - 1-402-00794-9 SN - 1568-2609 N1 - Serientitel: NATO science series : Series 2, Mathematics, physics and chemistry – Series title: NATO science series : Series 2, Mathematics, physics and chemistry IS - 78 SP - 283 EP - 290 PB - Kluwer Academics Publishers CY - Dordrecht AN - OPUS4-1548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Schriever, Sina A1 - Wossidlo, Peter A1 - Hamann, Andreas A1 - Löwe, Peter T1 - Bruchmechanische Untersuchungen von Gusseisen mit Kugelgraphit bei Stoss- und Schlagbiege-Beanspruchung T2 - 33. Tagung des DVM-Arbeitskreises Bruchvorgänge CY - Paderborn, Deutschland DA - 2001-02-20 KW - Ductile cast iron KW - DCI KW - Dynamic fracture toughness PY - 2001 SN - 0943-3473 N1 - Sprachen: Deutsch/Englisch - Languages: German/English IS - 233 SP - 267 EP - 274 PB - DVM CY - Berlin AN - OPUS4-1088 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Baer, Wolfram A1 - Klingbeil, Dietmar A1 - Häcker, Ralf A1 - Wossidlo, Peter A1 - Aurich, Dietmar ED - Neimitz, A. T1 - Investigations on the Assessment of the Toughness Behaviour in the upper Ductile-to-Brittle Transition Range T2 - 14th European Conference on Fracture ; 14th Biennial Conference on Fracture (ECF-14) CY - Cracow, Poland DA - 2002-09-08 PY - 2002 SN - 1-901537-38-2 VL - 3 SP - 185 EP - 192 PB - EMAS Publ. CY - Sheffield AN - OPUS4-1926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Klingbeil, Dietmar A1 - Eberle, Arno A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Häcker, Ralf ED - François, D. ED - Pineau, A. T1 - The calculation of dynamic JR-curves from 2D and 3D finite element analyses of a charpy test using a rate-dependent damage model T2 - Charpy Centenary Conference CY - Poitiers, France DA - 2001-01-02 PY - 2001 SN - 0-08-043970-5 SN - 1566-1369 N1 - Serientitel: ESIS publication – Series title: ESIS publication IS - 30 SP - 403 EP - 410 PB - Elsevier CY - Amsterdam AN - OPUS4-1928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Müller, Karsten A1 - Wossidlo, Peter T1 - Investigations on the Dynamic Fracture Toughness of Heavy-Section Ductile Cast Iron for Transport and Storage Casks T2 - PATRAM 2001 ; Annual International Symposium on Packaging and Transportation of Radioactive Materials CY - Chicago, IL, USA DA - 2001-09-03 PY - 2001 IS - CD-ROM PB - PATRAM CY - Chicago, Ill. AN - OPUS4-1930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Karsten A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Klingbeil, Dietmar ED - Neimitz, A. T1 - Investigations on the Dynamic Fracture Toughness Behaviour of Nodular Cast Iron T2 - 14th European Conference on Fracture ; 14th Biennial Conference on Fracture (14-ECF) CY - Cracow, Poland DA - 2002-09-08 PY - 2002 SN - 1-901537-37-4 VL - 2 SP - 501 EP - 508 PB - EMAS Publ. CY - Sheffield AN - OPUS4-1931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Baer, Wolfram A1 - Wossidlo, Peter T1 - Investigation on the Dynamic Fracture Toughness of Heavy-Section Ductile Cast Iron for Transport and Storage Casks T2 - PATRAM 2001 ; Annual International Symposium on Packaging and Transportation of Radioactive Materials CY - Chicago, IL, USA DA - 2001-09-03 PY - 2001 IS - CD-ROM PB - PATRAM CY - Chicago, Ill. AN - OPUS4-1886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Häcker, Ralf A1 - Wossidlo, Peter ED - Pohl, M. T1 - Der Einfluss der Belastungsgeschwindigkeit im Zugversuch auf die Anforderungen an die Messtechnik und auf das Probenverhalten T2 - Werkstoffprüfung - Konstruktion, Qualitätssicherung und Schadensanalyse CY - Neu-Ulm, Deutschland DA - 2004-11-25 KW - Werkstoffprüfung KW - Dynamischer Zugversuch KW - Messtechnik KW - Fließkurve KW - Spannungs-Dehnungskurve PY - 2004 SN - 3-88355-337-9 SP - 61 EP - 66 PB - Werkstoff-Informationsges. CY - Frankfurt AN - OPUS4-5057 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Abbasi, Behboud T1 - On the question of how to analyze and apply Charpy pendulum impact test results correctly - Shortcomings in corresponding procedures and standards N2 - This paper is focused on the approximation of absorbed Charpy impact energy-temperature curves (KV-T) and the management of sub-size test piece results in Charpy pendulum impact tests. Both subjects are frequently underestimated but may have a strong impact on the assessment of product quality and structural integrity. The status of related test standards, product standards, structural integrity assessment procedures and corresponding research is reviewed. It is concluded that the state of regulation is partly insufficient and wrong. There is a wide gap between the state of knowledge in the field of materials testing and the requirements of product standards and structural integrity assessment procedures. The present paper aims at boosting and supporting the necessary discussion among the parties involved to raise the level of technical safety. Correspondingly, a large experimental database was created by Charpy impact testing of popular modern structural Steels with nominal yield strength from 235 MPa to 960 MPa. KV-T data were generated using test pieces with thicknesses between 2.5 mm and 10 mm. Different strategies for KV-T curve fitting, definition of transition temperatures, as well as upper and lower shelf energy levels were followed, and different scaling procedures were applied to the sub-size test piece results. The results show that proportional scaling of sub-size to full-size test piece results in terms of KV should be disallowed because it is a wrong approach. Regulations still incorporating such procedures should be revised as soon as possible. Existing nonproportional scaling and conversion procedures were applied. The results obtained illustrate that neither an overall nor consistent conservatism nor an adequate conservatism level can be achieved. In summary, the standardizing bodies should enforce the discussion to revise relevant test standards considering more precise specifications on Charpy data fitting. Furthermore, proposals are made for an improved management of sub-size test piece results. KW - Structural integrity assessment procedure KW - Charpy pendulum impact test KW - Sub-size test piece KW - Standard test piece KW - Curve fitting KW - Conversion of results KW - Absorbed energy KW - Transition temperature KW - Steel KW - Test standard KW - Product standard PY - 2022 U6 - https://doi.org/10.1520/JTE20210781 SN - 0090-3973 VL - 50 IS - 4 SP - 2268 EP - 2293 PB - American Society for Testing and Materials (ASTM) CY - West Conshohocken, PA AN - OPUS4-55172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Breidung, Marc A1 - Wossidlo, Peter A1 - Wahl, Ken A1 - Gerwien, Peter A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Küppers, M. ED - Zimmermann, Martina T1 - Gezielte Werkstoffprüfung zur fail-safe-Bauteilauslegung am Beispiel eines Achsschenkels N2 - Bei der Auslegung von Achsschenkeln für Nutzfahrzeuge wird für den Überlastfall ein fail-safe-Kriterium (kontrolliertes Versagen) als Basisphilosophie angesetzt. Gefordert wird, dass sich der Achsschenkel auch unter Akzeptanz begrenzten Risswachstums hinreichend elastisch-plastisch verformen kann, ohne dass es zum Bruch kommt. Der Fahrer soll anschließend anhand der bleibenden Verformungen bemerken können, dass mit seinem Fahrzeug etwas nicht in Ordnung ist. Eine Voraussetzung für dieses Bauteilverhalten ist eine hinreichende Bruchzähigkeit des Werkstoffs. Diese, wie auch die Rissspitzenbeanspruchung, müssen ermittelt werden, um den bruchmechanischen Sicherheitsnachweis führen zu können. Zur Ermittlung der mechanisch-technologischen und bruchmechanischen Werkstoffeigenschaften wurde ein Prüfkonzept entwickelt, bei dem die Proben an der potenziell kritischen Stelle direkt aus den geschmiedeten Achsschenkeln entnommen werden. Die experimentelle Werkstoffcharakterisierung bildet dann die Beanspruchungsbedingungen beim Überlastereignis ab. Im Rahmen der Produktion stehen jedoch nur Kerbschlagarbeitswerte zur Verfügung und aufwändige bruchmechanische Versuche sollen vermieden werden. Deshalb wurde eine Korrelation zur Abschätzung der vorhandenen Bruchzähigkeit aus der Kerbschlagarbeit herangezogen. Es ergibt sich eine Ergebnismatrix, die die Einflussgrößen Versagenswahrscheinlichkeit, Temperatur und Bruchzähigkeit verknüpft. Abschließend wird ein erster Vergleich der abgeschätzten mit den experimentell ermittelten Bruchzähigkeitswerten gezogen. Dieser weist aus, dass die abgeschätzten Werte geringfügig konservativ sind. T2 - 40. Vortrags- und Diskussionstagung Werkstoffprüfung 2022 CY - Dresden, Germany DA - 27.10.2022 KW - Kerbschlagarbeit KW - Achsschenkel KW - Fail-safe KW - Bruchmechanische Auslegung KW - Korrelation PY - 2022 SP - 1 EP - 6 PB - DGM - Deutsche Gesellschaft für Materialkunde e.V. CY - Sankt Augustin AN - OPUS4-56152 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Wossidlo, Peter ED - Zimmermann, M. T1 - Zur Frage der Verwendung von Untermaßprobenergebnissen des Kerbschlagbiegeversuchs - Eine ernüchternde Bilanz N2 - Der Kerbschlagbiegeversuch ist seit der ersten Hälfte des letzten Jahrhunderts standardisiert und seit langem als Prüfverfahren international genormt. Weltweit sind zu garantierende Werte der Kerbschlagenergie (KV) und Übergangstemperaturen (TÜ) in Produktnormen und Regelwerken festgelegt. Unter bestimmten Bedingungen besteht dabei die Option, statt Normalproben Untermaßproben zu prüfen. Im Rahmen einer Untersuchung der BAM wurde der aktuelle Status von Prüf- und Produktnormen sowie Regelwerken zur Bewertung der Bauteilintegrität hinsichtlich ihres Umgangs mit Untermaßprobenergebnissen erfasst. Zur Schaffung einer geeigneten aktuellen Datenbasis wurden an ISO-V-Proben der Dicken 2,5, 5,0, 7,5 und 10,0 mm aus vier aktuellen Baustählen KV2-T-Kurven ermittelt. Es wurden unterschiedliche Vorgehensweisen zur Kurvenanpassung und Festlegung von Übergangstemperaturen praktiziert. Ferner kamen verfügbare Ansätze zur Skalierung von Untermaßprobenergebnissen auf die Werte von Normalproben zur Anwendung. Das Ausmaß des Probendickeneffektes ist werkstoff- und temperaturabhängig. Im Bereich der Werkstoffprüfung ist akzeptiert, dass die Ergebnisse von Normal- und Untermaß-proben nicht ohne Weiteres ineinander überführt werden können. Der Stand der Produktnormung und der Regelwerke ist jedoch im besten Falle als unzureichend, vielfach jedoch schlicht als falsch zu bezeichnen. In einem weiten anwendungsrelevanten Temperaturbereich werden hier sogar deutlich nicht-konservative Skalierungsergebnisse geliefert. Die betroffenen Produkt-normenreihen und Regelwerke müssen überarbeitet werden. T2 - 40. Vortrags- und Diskussionstagung Werkstoffprüfung 2022: Werkstoffe und Bauteile auf dem Prüfstand, Prüftechnik – Kennwertermittlung – Schadensvermeidung CY - Dresden, Germany DA - 27.10.2022 KW - Kerbschlagbiegeversuch, Untermaßproben, Normalproben, Skalierung von Ergebnissen PY - 2022 SP - 1 EP - 6 PB - Deutsche Gesellschaft für Materialkunde (DGM) CY - Sankt Augustin AN - OPUS4-56155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Habib, Abdel Karim T1 - Damage evolution detection in a pipeline segment under bending by means of acoustic emission N2 - A steel pipeline segment of 2.5 m length was subjected to quasi-static four-point bending load in three steps for studying the initial cracking and damage accumulation based on the Acoustic Emission (AE) technique and by the direct current potential drop (DCPD) technique. For the latter, a new post-test analysis method was established. AE is found more sensitive to crack initiation than DCPD. Formation of mesoscopic and macroscopic cracks as well as their closure and the resulting friction generate weighted peak frequencies below 400 kHz, whereas microscopic cracking produces AE with broad band spectra identifiable by weighted peak frequencies above 400 kHz. Critical states alike the maximum load level and the leak opening were accompanied by peak amplitudes above 85 dBAE. This rather fundamental study provides a data base for possibly developing advanced strategies of detection and alarm systems based on acoustic monitoring of pipelines, or at least, steel structures. KW - Crack KW - Accoustic emission KW - Frequency domain KW - Potential drop technique KW - Fracture PY - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-565171 SN - 0308-0161 VL - 201 IS - 104863 SP - 1 EP - 9 PB - Elsevier Science CY - Amsterdam AN - OPUS4-56517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Häcker, Ralf A1 - Knothe, Esther A1 - Wossidlo, Peter ED - Pohl, M. T1 - Experimentelle Untersuchungen für die Anwendung von Materialmodellen zur numerischen Auslegung des Containments von Abgasturboladern T2 - Tagung Werkstoffprüfung 2010 CY - Neu-Ulm, Deutschland DA - 2010-12-02 KW - Abgasturbolader KW - Containment KW - Hochgeschwindigkeitsversuch PY - 2010 SN - 978-3-514-00778-9 SP - 317 EP - 322 PB - Verl. Stahleisen GmbH CY - Düsseldorf AN - OPUS4-22949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Cassau, Matthias A1 - Häcker, Ralf A1 - Kossert, Reimund T1 - Large scale testing and statistical analysis of dynamic fracture toughness of ductile cast iron KW - Dynamic fracture toughness KW - Ductile cast iron KW - Large scale test KW - Statistical analysis PY - 2009 U6 - https://doi.org/10.1016/j.engfracmech.2009.01.005 SN - 0013-7944 SN - 1873-7315 VL - 76 IS - 8 SP - 1024 EP - 1036 PB - Elsevier Science CY - Kidlington AN - OPUS4-19351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Häcker, Ralf A1 - Wossidlo, Peter T1 - Meßunsicherheiten bestimmen - Am Beispiel der Ermittlung von Rißwiderstandskurven PY - 1998 SN - 0025-5300 VL - 40 IS - 9 SP - 361 EP - 365 PB - Carl Hanser Verlag CY - München AN - OPUS4-33404 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Cassau, Matthias ED - Borsutzki, M. ED - Moninger, G. T1 - Zur Auswertung und Verwendung von Kerbschlagbiegeversuchsergebnissen - Fehler und Defizite in relevanten Normen N2 - Der Kerbschlagbiegeversuch ist als Prüfverfahren seit langem international genormt. Zu garantierende Kerbschlagarbeitswerte sind in Produktnormen weltweit festgelegt. Gleichwohl enthalten ganze Normenreihen für Stähle falsche Festlegungen zur Verwendung von Untermaßprobenergebnissen. Im Mittelpunkt der vorliegenden Studie stehen die Auswertung von KV-T-Daten und die Skalierung von Untermaßprobenergebnissen. Hierzu wurden an ISO-V-Proben der Breiten 2,5; 5; 7,5 und 10 mm aus vier Baustählen im Streckgrenzenbereich von 235 bis 960 MPa dicht belegte KV-T-Kurven ermittelt. Es wurden unterschiedliche Vorgehensweisen zur Kurvenanpassung und Festlegung von Übergangstemperaturen wie auch der Hoch- bzw. Tieflagenarbeit untersucht. Die Ergebnisse unterstreichen unter anderem, dass die in festgelegte Vorgehensweise, nach der Untermaßprobenergebnisse proportional auf Normprobenmaße zu skalieren sind, nicht nur zu falschen, sondern auch nicht-konservativen Kerbschlagarbeitswerten führen kann. Das Ausmaß dieses Probenbreiteneffektes ist Werkstoff- und temperaturabhängig. Da die Kerbschlagarbeit als Abnahmekriterium verwendet wird, ergeben sich unmittelbare wirtschaftliche und sicherheitstechnische Konsequenzen. Es ist zu schlussfolgern, dass die entsprechenden Produktnormenreihen dringend zu überarbeiten sind. T2 - Tagung Werkstoffprüfung 2014 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Bad Neuenahr, Germany DA - 03.12.2015 KW - Kerbschlagbiegeversuch KW - Untermaßproben KW - Bewertung PY - 2015 SN - 978-3-514-00816-8 SP - 181 EP - 186 PB - Verlag Stahleisen CY - Düsseldorf AN - OPUS4-35082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eberle, Arno A1 - Häcker, Ralf A1 - Klingbeil, Dietmar A1 - Wossidlo, Peter T1 - Experimentelle und numerische ERmittlung dynamischer Risswiderstandskurven im Kerbschlagbiegeversuch N2 - Die bruchmechanische Beurteilung von Komponenten erfordert die Kenntnis von Risswiderstandskurven, die jedoch häufig aufgrund fehlenden Probenmaterials nicht zur Verfügung stehen. Vielmehr sind typische werkstofftechnische Kennwerte verfügbar, wie Streckgrenze, Zugfestig, Gleichmaßdehnung, Bruchdehnung sowie die Kerbschlagarbeit in der Hochlage und die laterale Breitung von Kerbschlagbiegeproben. Das Materialmodell von Gurson beschreibt duktiles Risswachstum mit den Stadien Hohlraumentstehung, Hohlraumwachstum und Koaleszenz benachbarter Hohlräume bis zum makroskopischen Riss. Die Materialparameter des Gurson-Modells sind abhängig vom Werkstoff und der Temperatur, jedoch nicht von der Probengeometrie und Belastungsgeschwindigkeit, was eine Übertragung zwischen quasistatisch belasteten Bruchmechanikproben unterschiedlicher Geometrie und schlagartig belasteten Kerbschlagbiegeproben erlaubt. Im vorliegenden Beitrag wird eine Methode zur Konstruktion von Risswiderstandskurven vorgestellt, die auf den grundlegenden Daten des Zugversuchs und der Kenntnis der Fließkurve basiert. Die Fließkurve bei dynamischer Belastung wird durch erprobte Vorgehensweisen ermittelt, die auf der Analyse der dann erhöhten Aktivierungsenergie von Versetzungen basieren. Die Parameter der duktilen Schädigung werden im wesentlichen durch die Simulation von Versuchen an gekerbten Rundzugproben und des Kerbschlagbiegeversuchs bzw. der Anpassung an die Kerbschlagarbeit in der Hochlage bestimmt. Damit sind die Parameter der duktilen Schädigung bekannt, so dass durch die Simulation duktilen Rissfortschritts in Bruchmechanikproben die erforderlichen J-Risswiderstandskurven zur Verfügung gestellt werden können, was die Anwendung des klassischen J-Konzepts erlaubt. Wegen der Geometrieunabhängigkeit der ermittelten Materialparameter ist auch die direkte Anwendung des Gurson-Modells zur Sicherheitsanalyse angerissener Bauteile durchführbar. PY - 2001 SN - 0933-5137 SN - 1521-4052 VL - 32 IS - 6 SP - 532 EP - 538 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-33718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Chruscicki, Sebastian A1 - Homann, Tobias A1 - Seifert, Stefan A1 - Schmidt, Dirk A1 - Weltschev, Margit A1 - Wossidlo, Peter A1 - Habib, Abdel Karim T1 - Monitoring of pipes by distributed acoustic fibre optic sensors – A large-scale test on a pipeline under realistic operation condition N2 - The monitoring of oil and gas pipelines by means of distributed fibre optic sensors is becoming common. The most recent development in the field of fibre optic sensing is the distributed acoustic sensing (DAS), which allows to detect and to localize third party threats to pipelines. For this purpose, fibre optic telecommunication cables located close to the pipelines are usually used. However, DAS carries a far greater potential for continuous condition monitoring of pipelines. The interdisciplinary research project AGIFAMOR (Ageing Infrastructures – Fibre Optic Monitoring of Pipes) at BAM investigates a new technical approach to extend the application field of DAS towards the detection and localization of acoustic signals that indicate critical alterations and certain damage scenarios originated from within the pipeline or the pipe wall. Therefore, the optical fibre sensors are applied onto the pipe itself and the application procedure towards an optimal acoustic signal transduction is optimized. A number of laboratory scale experiments were performed focusing on the signal transmission of acoustic signals as well as the detection of damages in the pipe wall by means of DAS. Furthermore, real-scale tests on a pipeline DN100 of 38m length have been carried out at the BAM test site for technical safety (BAM-TTS) to study the detection and localization of leaks and of changing flow profiles due to corrosion or sedimentation processes. T2 - 13th Pipeline Technology Conference CY - Berlin, Germany DA - 12.03.2018 KW - Pipeline monitoring KW - Distributed acoustic sensing KW - Fiber optic sensing PY - 2018 SN - 2198-428X SP - Poster session, paper 9, 1 EP - 8 PB - EITEP (Euro Institute for Information and Technology Transfer in Environmental Protection) CY - Hannover AN - OPUS4-44519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Chruscicki, Sebastian A1 - Homann, Tobias A1 - Prager, Jens A1 - Schmidt, Dirk A1 - Stajanca, Pavol A1 - Weltschev, Margit A1 - Wossidlo, Peter A1 - Habib, Abdel Karim T1 - AGIFAMOR: Anwendung der verteilten akustischen und faseroptischen Sensorik zur kontinuierlichen Überwachung von Rohrleitungen - Teil 2: Technische Hintergründe - Schadensursachen und Prüfeinrichtungen N2 - Schäden an Rohrleitungen können zu hohen Umweltbelastungen und wirtschaftlichen Schäden führen. Um die dauerhafte Verfügbarkeit der Infrastruktur zu gewährleisten, wird im Rahmen des Projekts AGIFAMOR an der Bundesanstalt für Materialforschung und -prüfung (BAM) erprobt, inwiefern das Verfahren der verteilten akustischen faseroptischen Sensorik (Distributed acoustic sensing – DAS) zur kontinuierlichen Überwachung von Rohrleitungen eingesetzt werden kann. Neben der DAS werden erprobte Verfahren der zerstörungsfreien Prüfung wie Schallemissionsanalyse (SEA) und Beschleunigungssensoren eingesetzt. An dieser Stelle soll detailliert auf die Hauptschadensursachen an Rohrleitungen, den Versuchsstand zur mechanischen Belastung von Rohren sowie die Möglichkeiten zu Untersuchungen im Realmaßstab eingegangen werden. KW - Schadensursachen an Rohrleitungen KW - Monitoring von Rohrleitungen KW - Verteilte Faseroptische Sensorik KW - Rohrbiegeprüfstand KW - Leckage PY - 2018 SN - 2191-0073 VL - 8 IS - 3 SP - 24 EP - 29 PB - Springer VDI-Verlag GmbH & Co. KG CY - Düsseldorf AN - OPUS4-44507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Hussels, Maria-Teresa A1 - Chruscicki, Sebastian A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Homann, Tobias A1 - Prager, Jens A1 - Schmidt, Dirk A1 - Weltschev, Margit A1 - Habib, Abdel Karim T1 - BAM-Projekt AGIFAMOR – Zustandsüberwachung von Rohrleitungen N2 - Rohrleitungssysteme sind aufgrund ihrer Funktion und Ausdehnung für den Betrieb, die Verfügbarkeit und die Sicherheit von Industrieanlagen von besonderer Bedeutung. Die bisher in definierten Intervallen durchgeführten, wiederkehrenden Prüfungen zur Sicherstellung leckagefreier Rohrleitungen sind kostenintensiv und mit einem erhöhten Aufwand verbunden. Mit dem interdisziplinären Forschungsprojekt AGIFAMOR (Ageing Infrastructures – Akustisches Monitoring von Rohrleitungen) arbeitet die BAM an der Entwicklung und Erprobung einer örtlich und zeitlich kontinuierlichen Zustandsüberwachung von Rohrleitungen basierend auf einem faseroptischen akustischen Messsystem, welches einen vergleichsweise geringen Installationsaufwand der Sensoren erfordert. Mit diesem Verfahren sollen vor allem betriebsbedingte Schädigungen infolge von Korrosion sowie daraus entstehende Pittings oder Risse erkannt und damit Leckagen verhindert werden. Im Rahmen einer Machbarkeitsstudie zum Teilaspekt „Detektion von Risswachstum“ wurde ein 2,5 m langes, definiert vorgekerbtes Stahlrohr mit der faseroptischen Sensorik (FOS) ausgestattet und quasistatisch unter 4-Punkt-Biegung belastet. Mit fortschreitender Belastung wächst, ausgehend vom vorhandenen Außenumfangskerb, ein Riss im Stahlrohr bis zum Erreichen der Leckage – in der Praxis ein gefährliches Schadensszenario. Parallel zur FOS erfolgten Messungen mit Schallemissionssensoren, Beschleunigungssensoren und Potentialsonden, deren Ergebnisse die Interpretation der FOS-Messergebnisse unterstützen sollen. T2 - 21. Kolloquium Schallemission CY - Fulda, Germany DA - 09.03.2017 KW - Beschleunigungssensoren KW - Faseroptische Sensorik KW - Schallemission KW - Monitoring KW - Rohrleitung PY - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-401811 SN - 978-3-940283-82-5 VL - DGZfP-BB 159 SP - Vortrag 17, 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-40181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baensch, Franziska A1 - Hussels, Maria-Teresa A1 - Chruscicki, Sebastian A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Homann, Tobias A1 - Prager, Jens A1 - Schmidt, Dirk A1 - Weltschev, Margit A1 - Habib, Abdel Karim T1 - AGIFAMOR: Anwendung der verteilten akustischen und faseroptischen Sensorik zur kontinuierlichen Überwachung von Rohrleitungen - Teil 1: Projektvorstellung und erste Vorversuche N2 - In der Prozessindustrie werden häufig gefährliche Stoffe eingesetzt, so dass auch kleinste Leckagen der medienführenden Anlagenteile zu Gefährdungen der Arbeitnehmer sowie zur Belastung der Umwelt führen können. Für die Gewährleistung einer dauerhaften Verfügbarkeit der Infrastruktur ist die frühzeitige Erkennung und Ortung von potentiell gefährlichen Veränderungen an den Wandungen von Rohrleitungen und Behältern (in Form von Rissen, Pittings und Ablagerungen) erforderlich. Am Beispiel von Rohrleitungen, sollen im Rahmen des Projekts AGIFAMOR an der Bundesanstalt für Materialforschung und -prüfung (BAM), im Sinne einer Machbarkeitsstudie die Verfahren der verteilten akustischen und faseroptischen Sensorik zur kontinuierlichen Überwachung und Detektion potentiell gefährlicher Veränderungen in Industrieanlagen erprobt und qualifiziert werden. Dabei sollen die Applikation der optischen Sensorfasern hinsichtlich der Signalübertragung auf den Sensor optimiert und die Erkennung der für dieses Anwendungsgebiet relevanten Schallsignaturen entwickelt werden. Mithilfe eines solchen Messsystems können mit geringem Aufwand ausgedehnte Strukturen, auch unter erschwerten Bedingungen (z.B. hohe Temperatur, Einfluss von Chemikalien) kontinuierlich überwacht werden. KW - Beschleunigungssensoren KW - Faseroptische Sensorik KW - Schallemission KW - Monitoring KW - Rohrleitung PY - 2017 SN - 2191-0073 VL - 7 IS - 3 SP - 10 EP - 16 PB - Springer VDI-Verlag GmbH & Co. KG CY - Düsseldorf AN - OPUS4-40183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hussels, Maria-Teresa A1 - Chruscicki, Sebastian A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Weltschev, Margit A1 - Schmidt, Dirk A1 - Baensch, Franziska A1 - Bohse, Jürgen A1 - Prager, Jens A1 - Habib, Abdel Karim T1 - AGIFAMOR – Application of distributed acoustic and fibre optic sensors for continuous monitoring of pipes N2 - Pipelines and industrial piping systems are particularly relevant regarding technical safety, availability and maintenance. Large flow rates of hazardous substances imply that even smallest leakages can lead to high environmental impacts. Therefore, and to ensure the availability of infrastructure, an early detection and localization of potentially hazardous degradations to the walls (e.g. cracks, pittings, sedimentation, etc.) of the containments is necessary. However, in many cases it is not feasible to equip pipelines with a large number of point sensors at reasonable expense. The principle of distributed fibre optic sensing relies on one single optical fibre, which simultaneously acts as a spatially continuous sensor as well as the signal transducer. Therefore, extensive structures can be provided with this type of sensor with comparatively low efforts. As a consequence, monitoring oil and gas pipelines using distributed fibre optic sensors is on the upswing. Besides the established methods to measure temperature and strain, distributed acoustic sensing (DAS) has lately received considerable attention as a means to detect and localize third party threats to pipelines (approach of vehicles, digging, mechanical manipulation). The so far not utilized potential of DAS as a means for continuous condition monitoring of pipes by detecting and localizing acoustic signals that point to certain damage scenarios, is currently under investigation in an interdisciplinary research project at BAM (AGIFAMOR, Ageing Infrastructures – Fibre Optic Monitoring of Pipes). In order to qualify distributed acoustic fibre optic sensors for this application area, we especially focus on detecting and identifying the relevant acoustic emissions of interesting degradations as well as on the optimal way of application of the optical fibres to the specimen to achieve an optimal signal transmission of acoustic signals. T2 - 12th Pipeline Technology Conference CY - Berlin, Germany DA - 02.05.2017 KW - Monitoring KW - Pipelines KW - Fibre optic sensing KW - Acoustic emission KW - Accelerometer PY - 2017 SN - 2198-428X VL - 2017 SP - Session 3.2 Leak Detection, 1 EP - 8 PB - EITEP (Euro Institute for Information and Technology Transfer in Environmental Protection) CY - Hannover AN - OPUS4-40186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baer, Wolfram A1 - Wossidlo, Peter T1 - Validation of a low blow specimen technique for R-curve determination using a drop tower N2 - Fracture mechanics based component design requires appropriate fracture mechanics toughness data with respect to both, loading rate as well as test temperature. Taking high-rate loading into account such as with accidental scenarios, different standards such as ASTM E 1820 or BS 7448-3 provide some information on dynamic fracture mechanics testing. Nevertheless, the designations differ so that a validation of the own material specific test method used for dynamic R-curve determination is mandatory. In order to address this for ductile cast iron materials an experimental method for the reliable determination of dynamic J-integral crack resistance curves at -40 °C following the multiple specimen approach has been established and validated. The experimental concept offers some additional valuable features. Single values of dynamic crack initiation toughness can be determined using a single specimen technique based on crack sensors. Furthermore, an experimentally independent method is provided according to which CTOD δ5 R-curves can be established. The focus of the present paper is on the validation of the experimental low blow technique using a drop tower test system. A drop tower test system was developed and set up to perform low blow tests at temperatures down to -40 °C. The system allows for a variation of the impact mass and height and was optimized for testing of ductile cast iron at stress intensity rates from approximately 5∙10⁴ to 3∙10⁵ MPa√ms⁻¹. This range of loading rate is characteristic for instance with crash scenarios of heavy sectioned DCI casks for radioactive materials. In order to address characteristic challenges of impact tests (test duration of microseconds up to milliseconds, inertial effects, signal oscillations), an appropriate full bridge strain gage method for the measurement of force directly on the specimen as well as a non-contact measurement of load line displacement using an optical extensometer have been developed and validated. The low blow test requires either to prevent bouncing strikes of the hammer by using the stop block technique or to catch the hammer after its first strike. Both options are not part of the experimental concept and setup which have been realized here. The paper describes investigations which have been performed in order to make sure that bouncing strikes of the hammer do not cause additional crack extension in the specimen. This is necessary to ensure a unique relation between the work done and the achieved crack extension. The investigations covered the analysis of limit loads of the specimen with respect to the measured force. The measured stiffness of the specimen was assessed and signals of crack sensors were analyzed. Furthermore, an analysis of the mechanical behavior of the loading system and the specimen by optical observation was performed. Corresponding results are discussed in the paper. It had finally been proven that additional crack extension in the specimen due to bouncing strikes of the hammer is not to be expected under the given conditions of test setup, material and loading. It can be seen as a major experimental advantage that the striker does not have to be catched after the low blow test. T2 - XXIV Italian Group of Fracture Conference CY - Urbino, Italy DA - 01.03.2017 KW - Dynamic fracture mechanics KW - R-curve KW - Low blow KW - Ductile cast iron PY - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-437686 SN - 2452-3216 VL - 3 SP - 25 EP - 32 AN - OPUS4-43768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Wossidlo, Peter T1 - Experimental determination and analysis of dynamic fracture toughness data of ductile cast iron N2 - Ductile Cast Iron materials (DCI) have become important structural materials. Neverthe-less, to draw maximum benefit from DCIs property potential, tailored testing methods must be provided. The established dynamic Jd-R and CTOD 5d-R curve procedures are based on material specifically developed, independent experimental techniques but pro-vide almost matching results. This can be seen as additional validation of the Jd procedure which was mandatory. T2 - 14th International Conference on Fracture (ICF 14) CY - Rhodes, Greece DA - 18.07.2017 KW - Ductile cast iron KW - Fracture mechanics KW - Dynamic loading KW - Crack resistance curve KW - CTOD KW - J-integral PY - 2017 SP - Track 3, 1 EP - 2 AN - OPUS4-42721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Habib, Abdel Karim T1 - Non-threshold acoustic emission analysis of damage evolution in pipe segments of steel S355J2H under bending load N2 - Four-point bending tests were carried out to analyze the acoustic characteristics of damage development in pipe segments made of steel, grade S355J2H, being 2.5 m long with an outer diameter of 168 mm and 16 mm wall thickness. To induce stable crack growth, the pipe segments were pre-damaged by a 90°circumferential notch in the middle of the pipe length. While the pipe was quasi-statically loaded, microscopic damage and plastic deformation accumulated to form a macroscopic crack that grew through the pipe wall until leakage. For acoustic emission (AE) monitoring, four broadband sensors of type VS 900 M were mounted close to the notch. Continuous AE signal detection was performed by the non-threshold method. Advantages and disadvantages of the non-threshold AE monitoring compared to a commonly employed method analyzing only signals exceeding a predefined threshold are discussed. The results of AE analysis are compared to additional information on the crack growth detected by the direct current potential drop (DCPD) technique. These studies were carried out in the course of the interdisciplinary research project AGIFAMOR, Ageing infrastructures - distributed acoustic monitoring of pipes at BAM. T2 - 33rd European Conference on Acoustic Emission Testing CY - Senlis, France DA - 12.09.2018 KW - Acoustic emissions (AE) KW - Four-point bending test KW - Steel pipe KW - Crack initiation KW - Crack growth PY - 2018 SP - 340 EP - 347 CY - France, Senlis AN - OPUS4-45960 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Chruscicki, Sebastian A1 - Habib, Abdel Karim A1 - Homann, Tobias A1 - Hussels, Maria-Teresa A1 - Prager, Jens A1 - Schmidt, Dirk A1 - Stajanca, Pavol A1 - Weltschev, Margit A1 - Wossidlo, Peter T1 - Feasibility study - Continuous monitoring of pipes using distributed acoustic and fibre optic sensors N2 - The feasibility study „AGIFAMOR. Ageing infrastructures – distributed acoustic monitoring of pipes” is an interdisciplinary research project at BAM internally financed from 2015 to 2018. Therefore, the quite young fibre optic sensing technology of distributed acoustic sensing (DAS) was investigated to possibly be extended towards a global condition monitoring system for pipelines operating in real time. DAS is a highly dynamic fibre optic sensing technology based on the method of coherent optical time domain reflectometry (C-OTDR). DAS allows capturing strain changes in the range of kHz. For the experimental work, the most suitable application yielding an optimum sensitivity was proven by wrapping a standard single-mode silica fibre around the pipe. The DAS sensitivity was investigated regarding the detection of 1) incidents that initiate propagation of acoustic waves in the pipe wall, 2) changes inside the pipeline causing altered flow and 3) damage development in the pipe wall. Therefore, several testing setups in laboratory as well as in real scale were realized. For comparison purposes, experiments were accompanied by acoustic emission analyses and by measurements with accelerometers. DAS was found to be very sensitive to gas ignition and its propagation across the pipe. Furthermore, the ability of DAS to detect and localize acoustic signals associated with pipeline leakage was demonstrated. The detection of crack formation and propagation within the pipe wall by means of DAS was studied during bending tests on several pipe segments, but was not proven so far with certainty. As expected, these studies turned out as the most difficult challenge due to the random occurrence and transient nature of microscopic damage phenomena. T2 - Proceedings of the International Symposium on Structural Health Monitoring and Nondestructive Testing CY - Saarbrücken, Germany DA - 04.10.2018 KW - Accelerometers KW - Acoustic emission KW - Fibre optic acoustic sensing KW - Continous monitoring KW - Bending tests on pipe segments KW - Leak detection PY - 2018 SP - Paper 21 AN - OPUS4-46375 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Habib, Abdel Karim T1 - Frequenzanalyse von Schallemission an einem Stahlrohr unter Biegebeanspruchung N2 - Um ein tieferes Verständnis über die Schallemission bei der Entstehung und Ausbreitung von Rissen in Stahlrohrleitungen zu erlangen, wurde ein Stahlrohr der Güte S355J2H im Vierpunkt-Biegeversuch quasistatisch bis hin zum Wanddurchbruch (Leckage) belastet und mittels Schallemissionsmessung und Gleichstrompotentialmessung überwacht. Das Rohrsegment wurde durch einen 90°- Außenumfangskerb in der Mitte der Rohrlänge definiert vorgeschädigt, um davon ausgehend ein stabiles Risswachstum zu induzieren und die Analyse von Schallemission aus Rissereignissen, die am Kerb eintraten, sicherzustellen. Für die Schallemissionsmessung wurden vier Breitbandsensoren max. 105 mm vom Kerb entfernt montiert. Die Signalaufzeichnung erfolgte kontinuierlich und schwellwertunabhängig. Für die Gleichstrompotentialmessung wurde ein Gleichstrom von 300 A eingeleitet und der Potentialabfall über dem Kerb mit fünf Sonden entlang des Kerbs gemessen. Beide Messverfahren identifizieren die Rissinitiierung sowie Veränderungen im Risswachstum. Die detektierten Schallemissionsereignisse werden, unter Berücksichtigung spektraler Eigenschaften, mit fortschreitender Belastung und Rissentwicklung analysiert. Diese Studien wurden im Rahmen des interdisziplinären Forschungsprojekts AGIFAMOR, Aging infrastructure - Faseroptisches Monitoring von Rohrleitungen, an der BAM durchgeführt. T2 - 22. Kolloquium Schallemission und 3. Anwenderseminar Zustandsüberwachung mit geführten Wellen CY - Karlsruhe, Germany DA - 27.03.2019 KW - Schallemission KW - Frequenzanalyse KW - Rissbildung in Stahl PY - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-476888 SN - 978-3-947971-00-8 VL - 169 SP - 1 EP - 8 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-47688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Probst, Ulrich A1 - Hagenow, Peter A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Achelpöhler-Schulte, Andreas A1 - Schulz, Sebastian T1 - Investigation of seal effects according to axial compression variation of metal seals for transport and storage casks N2 - Casks for the transport and storage of heat generating radioactive waste in Germany are normally provided with screwed lid systems, which are in most cases equipped with double jacket metal seals with an inner spring wire to provide long term resistance to the seal compression force. Preservation of the high sealing quality of those seals under operational and accidental stress conditions is essentially important to the safety of those casks. Relative displacements of the lid system surfaces caused by specific impact scenarios cannot be excluded and have to be evaluated with respect to a possible increase in the leakage rate. To get representative data for such metal sealed lid systems, BAM has developed a special conceptualised flange system placed in an appropriate testing machine for relevant mechanical loading of the metal seals under static and cyclic conditions. Furthermore, the flange system enables continuous measurement of the standard helium leakage rate during each test. The primary aim of the investigation is to identify the correlation between variation of installation conditions (axial displacements) caused by external loads and the standard helium leakage rate. An essential parameter in this case is the useable resilience ru of a metal seal under relevant stress conditions. The useable resilience ru is the vertical difference in the cross-section between the seal's assembling status and the point where the leakage rate, by means of external load relieving, exceeds the quality criterion of 10-8 Pa m3 s-1. Load relieving can instantly occur due to modification of the seal groove dimension caused by accident impacts and deformation of the lid system. Furthermore, component specific basis data for the development of finite element calculation models should be collected. In the tests, seals are subjected to static and cyclic loads. All tests are performed at ambient temperature. This paper presents the test configuration, different test series and results of the current experiments. Typical load-displacement-leakage rate correlations are presented and discussed. KW - Seal effects KW - Axial compression variation KW - Metal seals KW - Helium leakage rate KW - Cyclic load PY - 2008 U6 - https://doi.org/10.1179/174651008X278948 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 19 IS - 1 SP - 47 EP - 52 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-17540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Probst, Ulrich A1 - Hagenow, Peter A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Achelpöhler-Schulte, Andreas A1 - Schulz, Sebastian T1 - Investigation of seal effects according to axial compression variation of metal seals for transport and storage casks T2 - PATRAM 2007, 15th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Miami, Florida, USA DA - 2007-10-21 KW - Metal Seals KW - Axial Compression KW - Cycling Tests KW - Helium Leakage Rate PY - 2007 SP - 1 EP - 8 PB - Institute of Nuclear Materials Management AN - OPUS4-17542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Goral, Milan A1 - Kömmling, Anja A1 - Probst, Ulrich A1 - Wossidlo, Peter A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Völzke, Holger T1 - Langzeitversuche über 10 Jahre an Federkern-Metalldichtungen mit Aluminium- bzw. Silberummantelungen N2 - Federunterstützte Metalldichtungen mit Aluminium(Al)- oder Silber(Ag)-Ummantelung werden u.a. in Behältern für Wärme entwickelnde radioaktive Abfälle eingesetzt, da diese Dichtungen eine sehr gute Dichtheit gewährleisten sowie Langlebigkeit und Beständigkeit gegenüber erhöhten Temperaturen und radioaktiver Strahlung aufweisen. Auch wenn die Sicherheit solcher Behälter und der verwendeten Dichtungen vielfach belegt wurde, sind sie Gegenstand andauernder Forschung, etwa im Hinblick auf eine absehbar benötigte verlängerte Zwischenlagerdauer. Aus diesem Grund werden an der Bundesanstalt für Materialforschung und -prüfung (BAM) im Fachbereich 3.4 „Sicherheit von Lagerbehältern“ seit über 20 Jahren Versuche an solchen Metalldichtungen durchgeführt. Dabei sollen zusätzliche Erkenntnisse hinsichtlich der Sicherheitsreserven der Dichtungen in unterstellten Störfallszenarien (axiale Bewegung des Deckelsystems bzw. Aufweitung der Nutgeometrie) und insbesondere detailliertere Erkenntnisse zum Langzeitverhalten gewonnen werden. KW - Federunterstützte Metalldichtungen KW - Transport- und Lagerbehälter für radioaktive Stoffe KW - Langzeitversuche KW - Alterung KW - Dichtheit KW - Leckagerate KW - Helium-Dichtheitsprüfung PY - 2023 VL - 2023 SP - 43 EP - 63 PB - ISGATEC GmbH CY - Mannheim AN - OPUS4-56399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -