TY - CONF A1 - Wondraczek, L. A1 - Reinsch, Stefan A1 - Gaber, Martin A1 - Deubener, J. A1 - Müller, Ralf A1 - Komatsu, T. T1 - Nano-crystalline germanate glass-ceramics T2 - 78. Glastechnische Tagung CY - Nürnberg, Deutschland DA - 2004-06-07 PY - 2004 SP - 37 EP - 40 PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-6953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wondraczek, L. A1 - Reinsch, Stefan A1 - Gaber, Martin A1 - Deubener, J. A1 - Müller, Ralf A1 - Komatsu, T. T1 - Nano-crystalline germanate glass-ceramics T2 - 78. Glastechnische Tagung CY - Nuremberg, Germany DA - 2004-06-07 PY - 2004 AN - OPUS4-5628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Winkel, A. A1 - Meszaros, R. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Travitzky, N. A1 - Fey, T. A1 - Greil, P. A1 - Wondraczek, L. T1 - Sintering of 3D-printed glass/HAp composites N2 - We report the sintering of 3D-printed composites of 13-93 bioactive glass and hydroxyapatite (HAp) powders. The sintering process is characterized on conventionally produced powder compacts with varying HAp content. A numeric approximation of the densification kinetics is then obtained on the basis of Frenkel, Mackenzie–Shuttleworth, and Einstein–Roscoe models, and optimized sintering conditions for 3D-printed structures are derived. Fully isotropic sintering of complex cellular composites is obtained by continuous heating to 750°C at a rate of 2 K/min for a HAp content of 40 wt%. The approach can readily be generalized for printing and sintering of similar glass-ceramic composites. KW - Sintering glass composit bio material PY - 2012 U6 - https://doi.org/10.1111/j.1551-2916.2012.05368.x SN - 0002-7820 SN - 1551-2916 VL - 95 IS - 11 SP - 3387 EP - 3393 PB - Blackwell Publishing CY - Malden AN - OPUS4-27053 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pönitzsch, A. A1 - Nofz, Marianne A1 - Wondraczek, L. A1 - Deubener, J. T1 - Bulk elastic properties, hardness and fatigue of calcium aluminosilicate glasses in the intermediate-silica range N2 - Bulk elastic properties, hardness and fatigue of calcium aluminosilicate (CAS) glasses in the technically relevant region of the ternary with intermediate-silica fraction were determined by combining results of Vickers indentation, ultrasonic echography and Archimedian buoyancy at room temperature. Of three studied compositional series, the first series was along the meta-aluminous join, while in the two other series the molar fraction of SiO2 was kept constant. For the first series the elastic moduli and hardness show an almost linear increase with increasing SiO2 fraction. In contrast, increasing the CaO/SiO2 ratio at constant silica content results in a characteristic change when passing the meta-aluminous join. Elastic constants and hardness were lower at the percalcic than on the peraluminous side. Empirical models which relate bulk elastic moduli to internal energy, short-range inter-atomic forces and the packing density of their oxide constituents were found to be in agreement with the experimental data for meta-aluminous glasses, while deviations between the observed and predicted trends were evident for percalcic compositions. Empirical fatigue parameters such as the probability to initiate cracks after indentation reflect the bulk mechanical properties in the CAS system when conducted in inert atmosphere, but are otherwise clearly dominated by environmental effects KW - Aluminosilicate glasses KW - Elastic constants KW - Indentation KW - Hardness KW - Crack initiation KW - Sub-critical crack-growth PY - 2016 U6 - https://doi.org/10.1016/j.jnoncrysol.2015.12.002 SN - 0022-3093 VL - 434 SP - 1 EP - 12 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-35243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seuthe, T. A1 - Mermillod-Blondin, A. A1 - Grehn, M. A1 - Bonse, Jörn A1 - Wondraczek, L. A1 - Eberstein, M. T1 - Structural relaxation phenomena in silicate glasses modifed by irradiation with femtosecond laser pulses N2 - Structural relaxation phenomena in binary and multicomponent lithium silicate glasses were studied upon irradiation with femtosecond (fs) laser pulses (800 nm central wavelength, 130 fs pulse duration) and subsequent thermal annealing experiments. Depending on the annealing temperature, micro-Raman spectroscopy analyses evidenced different relaxation behaviours, associated to bridging and non-bridging oxygen structures present in the glass network. The results indicate that the mobility of lithium ions is an important factor during the glass modification with fs-laser pulses. Quantitative phase contrast imaging (spatial light interference microscopy) revealed that these fs-laser induced structural modifications are closely related to local changes in the refractive index of the material. The results establish a promising strategy for tailoring fs-laser sensitivity of glasses through structural mobility. KW - Femtosecond laser KW - Silicate glasses KW - Raman spectroscopy KW - Structural relaxation KW - Refractive index PY - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-393045 SN - 2045-2322 VL - 7 SP - 43815, 1 EP - 43815, 10 PB - Nature Publishing Group CY - London, UK AN - OPUS4-39304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -