TY - CONF A1 - Bismarck, A. A1 - Carreyette, S. A1 - Fontana, Q.P.V. A1 - Greenhalgh, E.S. A1 - Jacobsson, P. A1 - Johansson, P. A1 - Marczewski, M.J. A1 - Kalinka, Gerhard A1 - Kucernak, A. A1 - Shaffer, M.S. A1 - Shirshova, N. A1 - Steinke, J.H.G. A1 - Wienrich, Malte T1 - Multifunctional epoxy resin for structural supercapacitors N2 - Polymer-based electrolytes based on commercially available epoxy resins were prepared through the addition of a liquid electrolyte, a solution of a lithium salt in an ionic liquid. The polymer monoliths were characterized using impedance spectroscopy, 3-point bending test, scanning electron microscopy (SEM) and nitrogen adsorption (BET). The balance of ionic conductivity and flexural modulus is crucially dependent on the relative proportions of epoxy resin to electrolyte. Also the effect of the liquid electrolyte on curing kinetics and processing was assessed by complex viscosity measurements and differential scanning calorimetry (DSC). Only one out of the three resins investigated exhibited a significant acceleration effect. T2 - ECCM15 - 15th European conference on composite materials CY - Venice, Italy DA - 2012-06-24 KW - Multifunctional epoxy KW - Polymer electrolyte KW - Morphology KW - Ionic liquid PY - 2012 SN - 978-88-88785-33-2 SP - 1 EP - 8(?) AN - OPUS4-28694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienrich, Malte A1 - Kalinka, Gerhard A1 - Greenhalgh, E.S. A1 - Carreyette, S. A1 - Bistritz, Martina A1 - Shirshova, N. A1 - Houllé, M. A1 - Asp, L. E. A1 - Bismarck, A. A1 - Fontana, Q.P.V. T1 - Impact of ionic liquid on the mechanical performance of matrix polymer for fibre reinforced materials for energy storage N2 - For the concept of using structural materials such as carbon fibre reinforced plastics as energy storage devices, new matrix polymers are required. These polymers must provide ionic conductivity as well as adequate mechanical strength. In the EU-Project StorAGE this requirements are fulfilled by adding ionic liquid to commercial polymers. The mechanical properties of these mixtures materials were characterized by using a 3-point-bending device. In addition, single fibre pull test were performed in order to get information on the interfacial shear strength. Adding of ionic liquid has an impact on the mechanical performance of the materials. A decrease of the flexural strength and modulus of less than 10% of the value of the reference materials took part. The interfacial shear strength decreased to a value of around one third compare to the reference material. T2 - ECCM15 - 15th European conference on composite materials CY - Venice, Italy DA - 2012-06-24 KW - Multifunctional epoxy resin KW - Fibre-matrix adhesion KW - Single fibre pull-out test KW - Ionic liquid PY - 2012 SN - 978-88-88785-33-2 SP - 1 EP - 4(?) AN - OPUS4-28695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienrich, Malte A1 - Kalinka, Gerhard A1 - Greenhalgh, E. A1 - Carreyette, Shuijin A1 - Bistritz, Martina A1 - Shirshova, Natasha A1 - Houllé, Matthieu A1 - Bismarck, A. T1 - IMPACT OF IONIC LIQUID ON THE MECHANICAL PERFORMANCE OF MATRIX POLYMER FOR FIBRE REINFORCED MATERIALS FOR ENERGY STORAGE T2 - ECCM 15 - European Conference on Composite Materials CY - Venice, Italy DA - 2012-06-24 PY - 2012 AN - OPUS4-27467 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Greenhalgh, E.S. A1 - Ankersen, J. A1 - Asp, L. E. A1 - Bismarck, A. A1 - Fontana, Q.P.V. A1 - Houlle, M. A1 - Kalinka, Gerhard A1 - Kucernak, A. A1 - Mistry, M. A1 - Nguyen, S. A1 - Qian, H. A1 - Shaffer, M.S.P. A1 - Shirshova, N. A1 - Steinke, J.H.G. A1 - Wienrich, Malte T1 - Mechanical and microstructural characterisation of multifunctional structural power composites N2 - Although the inherent anisotropy of polymer composites has presented daunting technical challenges, these materials now offer engineers considerable opportunities for efficient structural design. More recently, the advent of multifunctional composites which can fulfill more than one role within a system has attracted considerable interest, providing designers with exciting opportunities to innovate. Of particular interest here are structural power composites, which simultaneously carry mechanical load whilst storing/delivering electrical energy. Although the development of these composites is highly challenging, often with conflicting constituent requirements, the STORAGE consortium has had considerable success in the development of these materials for automotive applications. The focus of this paper is structural supercapacitors, the basic architecture of a single cell of which is shown in Fig. 1. This entails two carbon fibre woven lamina (electrodes) which sandwich a glass fibre woven lamina (separator), all of which is embedded within a multifunctional matrix (electrolyte). This architecture has been the focus of the research to date, leading to components such as that shown in Fig.1 having been fabricated. This paper reports on the mechanical properties and microstructures of the different reinforcement and matrix combinations for structural supercapacitors. T2 - ICCM19 - 19th International conference on composite materials CY - Montreal, Canada DA - 28.07.2013 KW - Structural electrolyte KW - Multifunctional supercapacitor KW - Fractography KW - Ionic conductivity KW - Mechanical properties PY - 2013 SP - 2228 EP - 2237 AN - OPUS4-29272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shirshova, N. A1 - Bismarck, A. A1 - Carreyette, S. A1 - Greenhalgh, E.S. A1 - Johansson, P. A1 - Marczewski, M.J. A1 - Jacobsson, P. A1 - Kalinka, Gerhard A1 - Shaffer, M.S.P. A1 - Wienrich, Malte A1 - Steinke, J.H.G. T1 - Correlations between mechanical properties and ionic conduction of structural electrolytes with bicontinuous morphologies N2 - Electrolyte systems that can carry mechanical load while allowing for high levels of ionic conductivity are an important prerequisite for structural power storage devices. Introduction of structural power storage into the variety of consumer products will allow saving in weight and volume. Moreover, using a supercapacitor/battery system in hybrid electric vehicles (HEV), the supercapacitor part will extend the battery lifetime by protecting it from the high peak currents. To successfully produce structural power storage requires the development of multifunctional electrolytes where one has to simultaneously maximize mechanical properties and ionic conductivity. T2 - ICCM19 - 19th International conference on composite materials CY - Montreal, Canada DA - 28.07.2013 KW - Structural electrolyte KW - Multifunctional supercapacitor KW - Bicontinuous morphology KW - Epoxy resin KW - Ionic conductivity KW - Mechanical properties PY - 2013 SP - 72 EP - 79 AN - OPUS4-29273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shirshova, N. A1 - Bismarck, A. A1 - Carreyette, S. A1 - Fontana, Q.P.V. A1 - Greenhalgh, E.S. A1 - Jacobsson, P. A1 - Johansson, P. A1 - Marczewski, M.J. A1 - Kalinka, Gerhard A1 - Kucernak, A.R.J. A1 - Scheers, J. A1 - Shaffer, M.S.P. A1 - Steinke, J.H.G. A1 - Wienrich, Malte T1 - Structural supercapacitor electrolytes based on bicontinuous ionic liquid-epoxy resin systems N2 - 'Structural electrolytes' retain the desirable mechanical characteristics of structural (epoxy) resins whilst introducing sufficient ionic conductivity to operate as electrolytes in electrochemical devices. Here, a series of ionic liquid–epoxy resin composites were prepared to identify the optimum system microstructure required to achieve a high level of multifunctionality. The ionic conductivity, mechanical properties, thermal stability and morphology of the cured epoxy based structural electrolytes were studied as a function of phase composition for three fully formulated high performance structural epoxy systems. At only 30 wt% of structural resin and 70 wt% of ionic liquid based electrolyte, stiff monolithic plaques with thicknesses of 2–3 mm were obtained with a room temperature ionic conductivity of 0.8 mS cm-1 and a Young's modulus of 0.2 GPa. This promising performance can be attributed to a long characteristic length scale spinodal microstructure, suggesting routes to further optimisation in the future. KW - Epoxy KW - Ionic liquid KW - Supercapacitor PY - 2013 U6 - https://doi.org/10.1039/c3ta13163g SN - 2050-7496 SN - 2050-7488 VL - 1 IS - 48 SP - 15300 EP - 15309 PB - RSC CY - London [u.a.] AN - OPUS4-29735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Blaker, J. J. A1 - Anthony, David B. A1 - Tang, G. A1 - Shamsuddin, S.-R. A1 - Kalinka, Gerhard A1 - Wienrich, Malte A1 - Abdolvand, Amin A1 - Shaffer, M. S. P. A1 - Bismarck, A. T1 - Property and shape modulation of carbon fibers using lasers N2 - An exciting challenge is to create unduloid-reinforcing fibers with tailored dimensions to produce synthetic composites with improved toughness and increased ductility. Continuous carbon fibers, the state-of-the-art reinforcement for structural composites, were modified via controlled laser irradiation to result in expanded outwardly tapered regions, as well as fibers with Q-tip (cotton-bud) end shapes. A pulsed laser treatment was used to introduce damage at the single carbon fiber level, creating expanded regions at predetermined points along the lengths of continuous carbon fibers, while maintaining much of their stiffness. The range of produced shapes was quantified and correlated to single fiber tensile properties. Mapped Raman spectroscopy was used to elucidate the local compositional and structural changes. Irradiation conditions were adjusted to create a swollen weakened region, such that fiber failure occurred in the laser treated Region producing two fiber ends with outwardly tapered ends. Loading the tapered fibers allows for viscoelastic energy dissipation during fiber pull-out by enhanced friction as the fibers plough through a matrix. In these tapered fibers, diameters were locally increased up to 53%, forming outward taper angles of up to 1.8°. The tensile strength and strain to failure of the modified fibers were significantly reduced, by 75% and 55%, respectively, ensuring localization of the break in the expanded region; however, the fiber stiffness was only reduced by 17%. Using harsher irradiation conditions, carbon fibers were completely cut, resulting in cottonbud fiber end shapes. Single fiber pull-out tests performed using these fibers revealed a 6.75-fold increase in work of pull-out compared to pristine carbon fibers. Controlled laser irradiation is a route to modify the shape of continuous carbon fibers along their lengths, as well as to cut them into controlled lengths leaving tapered or cotton-bud shapes. KW - Composite KW - Irradiation KW - Pull-out tests KW - Pulsed laser treatment KW - Single carbon fibers PY - 2016 U6 - https://doi.org/10.1021/acsami.6b05228 SN - 1944-8244 SN - 1944-8252 VL - 8 IS - 25 SP - 16351 EP - 16358 PB - ACS Publications CY - 1155 Sixteenth Street, NW, Washington, DC 20036, USA AN - OPUS4-37699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shirshova, N. A1 - Bismarck, A. A1 - Greenhalgh, E.S. A1 - Johansson, P. A1 - Kalinka, Gerhard A1 - Marczewski, M.J. A1 - Shaffer, M.S.P. A1 - Wienrich, Malte T1 - Composition as a means to control morphology and properties of epoxy based dual-phase structural electrolytes N2 - Structural electrolytes were prepared using a fully formulated commercially available high performance epoxy resin (MTM57) and an ionic liquid based electrolyte: lithium bis(trifluoromethylsulfonyl)imide (LiTFSI) dissolved in 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM-TFSI). Through a systematic study, the composition of the formulations was found to have a greater effect than the curing temperature on the morphology and properties of the resulting structural electrolytes. The presence of lithium salt is essential to form a structurally homogeneous electrolyte. Bicontinuous morphologies containing continuous (coarse) epoxy networks surrounded by connected spherical epoxy nodules were obtained with different length scales upon varying the lithium salt concentration. Increasing the LiTFSI concentration improved the miscibility of MTM57 with the electrolyte and decreased the characteristic length scale of the resulting bicontinuous microstructure. The properties of the structural electrolytes correlated with the morphology, showing increased Young’s modulus and decreased ionic conductivity with increasing lithium salt concentration. The miscibility of the epoxy system with the electrolyte was also improved by substitution of EMIM-TFSI with an equal weight of an aprotic organic solvent, propylene carbonate (PC); however, the window of PC concentrations which resulted in structural electrolytes with bicontinuous microstructures was very narrow; at PC concentrations above 1 wt %, gel-like polymers with no permanent mesoporosity were obtained. KW - Functional composites KW - Mechanical properties KW - Elastic properties KW - Epoxy KW - Morphology KW - Electrolyte PY - 2014 U6 - https://doi.org/10.1021/jp507952b SN - 1932-7447 SN - 1089-5639 VL - 118 IS - 49 SP - 28377 EP - 28387 PB - Soc. CY - Washington, DC AN - OPUS4-34565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Greenhalgh, E.S. A1 - Ankersen, J. A1 - Asp, L. E. A1 - Bismarck, A. A1 - Fontana, Q.P.V. A1 - Houlle, M. A1 - Kalinka, Gerhard A1 - Kucernak, A. A1 - Mistry, M. A1 - Nguyen, S. A1 - Qian, H. A1 - Shaffer, M.S.P. A1 - Shirshova, N. A1 - Steinke, J.H.G. A1 - Wienrich, Malte T1 - Mechanical, electrical and microstructural characterisation of multifunctional structural power composites N2 - Multifunctional composites which can fulfil more than one role within a system have attracted considerable interest. This work focusses on structural supercapacitors which simultaneously carry mechanical load whilst storing/delivering electrical energy. Critical mechanical properties (in-plane shear and in-plane compression performance) of two monofunctional and four multifunctional materials were characterised, which gave an insight into the relationships between these properties, the microstructures and fracture processes. The reinforcements included baseline T300 fabric, which was then either grafted or sized with carbon nanotubes, whilst the baseline matrix was MTM57, which was blended with ionic liquid and lithium salt (two concentrations) to imbue multifunctionality. The resulting composites exhibited a high degree of matrix heterogeneity, with the ionic liquid phase preferentially forming at the fibres, resulting in poor matrix-dominated properties. However, fibre-dominated properties were not depressed. Thus, it was demonstrated that these materials can now offer weight savings over conventional monofunctional systems when under modest loading. KW - Carbon fibres KW - Functional composites KW - Mechanical properties KW - Elastic properties KW - Fractography PY - 2014 U6 - https://doi.org/10.1177/0021998314554125 SN - 0021-9983 SN - 1530-793X SP - 1 EP - 12 PB - Sage CY - London AN - OPUS4-34567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -