TY - CONF A1 - Weltschev, Margit T1 - Use of Higher Alloyed Metallic Materials and Duplex Steels for Transport Tanks of Dangerous Goods T2 - Steels in Cars and Trucks (SCT 2011) CY - Salzburg, Austria DA - 2011-06-06 PY - 2011 AN - OPUS4-23801 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weltschev, Margit A1 - Bäßler, Ralph T1 - Use of alloy 59 for the transport of highly corrosive dangerous goods N2 - Alloy 59 (NiCr23Mo16Al) with a lot of chromium, molybdenum and nickel possesses excellent resistance not only to reducing but also oxidizing chemicals. Both the Nickel alloy 59 and the superaustenitic steel alloy 31 have already been used as shell materials for tank vehicles or tank containers. Use of these alloys allows the transport of a signifi-cantly more wider variety of chemicals and, especially, waste mixtures than the use of common aus-tenitic steels. Another advantage is the extension of test intervals of for transport tanks. In Germany the 'BAM-List – Requirements for Tanks for the Transport of Dangerous Goods' is the basis for substance-related prototype approvals for tank containers designed for the carriage of dangerous goods issued by the Federal Institute for Materials Research and Testing (BAM). Com-patibility evaluations of selected metallic material groups as well as polymeric gasket and lining materials under the influence of approximately 7000 dangerous goods and water-polluting sub-stances are published in the BAM-List. Alloy 59 belongs to the group of metallic materials in the BAM-List. Due to the large number of dangerous goods in the BAM-List BAM, IKS Dresden and ThyssenKrupp VDM performed a comprehensive corrosion test programme with welded specimens of the nickel alloy 59 and the superaustenitic steels alloy 926 and alloy 31 in the period 2002 - 2010. Especially In particular alloy 59 and alloy 31 were exposed to a large number of corrosive sub-stances such as various mixtures of both nitric acid/sulphuric acid and nitric acid/phosphoric acid at 55 °C. Other corrosive test substances were different organic and inorganic halogenides, peroxyace-tic acid and molten substances. In the case of molten chemicals such as monochloroacetic acid the test temperature was increased to more than 100 °C. The test results presented in this paper are al-ready included in the 10th edition of the BAM-List and, therefore, available to the customer. KW - Nickel alloy KW - Transport tanks of dangerous goods KW - Proof of compatibility KW - Transporttankwerkstoffe KW - Nickelbasislegierung KW - Korrosionstest KW - Korrosive Medien KW - BAM-Liste PY - 2005 DO - https://doi.org/10.4028/www.scientific.net/AMR.278.581 SN - 1022-6680 SN - 1662-8985 VL - 278 SP - 581 EP - 586 PB - Trans Tech Publ. CY - Zurich AN - OPUS4-24014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Compatibility of metallic tank and polymeric sealing materials with biofuels T2 - ACHEMA CY - Frankfurt am Main DA - 2015-06-15 PY - 2015 AN - OPUS4-33534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Weltschev, Margit T1 - Book review: Physical test methods for elastomers N2 - The book is primarely intended as a reference for those directly concerned with testing elastomers or for those indirectly involved in testing such as design engineers. KW - Elastomer PY - 2018 UR - https://doi.org/10.1002/maco.201870074 DO - https://doi.org/10.1002/maco.201870074 SN - 0947-5117 VL - 69 IS - 7 SP - 953 EP - 953 PB - WILEY-VCH Verlag GmbH & Co. KGaA CY - Weinheim AN - OPUS4-46746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Bäßler, Ralph T1 - Comparison of the corrosion resistance to dangerous goods of austenitic CrNiMo and duplex steels N2 - The “BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” is the basis in Germany for substance-related prototype approvals for tank Containers in Germany. Compatibility evaluations of selected metallic materials and polymeric materials under the influence of approximately 7200 dangerous goods have been published in the BAM-List since 1989. The austenitic CrNi- and CrNiMo-steels - UNS S30403, UNS S31600, UNSS31603 and UNS S31635 - are the materials mostly used worldwide for transport tanks. The duplex Steel UNS S31803 has been put on the BAMList due to the great interest of tank producers and transport Companies. Using UNS S31803 instead of 316L, the weight of the tanks can be reduced, and the list of transportable goods can be extended. The objective of these investigations was to compare the corrosion resistance of duplex Steel UNS S31803 and austenitic Steel UNS S31603. Therefore, test specimens of both steels were exposed to selected corrosive substances, such as formic acid, acetic acid, phosphoric acid, sulfuric acid, nitrating acid, monochloroacetic acid and trichloroacetone at 55 °C (30 °C, 70 °C). The test results have shown that the duplex Steel UNSS31803 is a good alternative to austenitic CrNiMo-steel UNS S31603 for tanks carrying corrosive dangerous goods. T2 - Corrosion 2014 CY - San Antonio, TX, USA DA - 09.03.2014 KW - Austenitic CrNiMo steel KW - Duplex steel KW - Corrosion resistance KW - Dangerous goods KW - BAM-list PY - 2014 SP - Paper 3786, 1 EP - 11 AN - OPUS4-30412 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Weltschev, Margit A1 - Bäßler, Ralph A1 - Werner, H. A1 - Alves, H. ED - Bernhard Fuchsbauer, ED - Wieland, Hans-Joachim T1 - Use of Corrosion-Resistant Higher-Alloyed Metallic Materials for the Transport of Dangerous Goods in Tanks T2 - 2nd Conference Steels in Cars and Trucks (SCT2008) "Future trends in steel development, processing technologies and applications" - Bringing the automotive, supplier and steel industries together CY - Wiesbaden, Germany DA - 2008-06-01 KW - BAM-List KW - Corrosion resistance KW - Dangerous goods KW - Superaustenitic steels KW - Nickel alloy PY - 2008 SN - 978-3-514-00755-0 SP - 53 EP - 62 PB - Verl. Stahleisen GmbH CY - Düsseldorf AN - OPUS4-17566 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Sina A1 - Weltschev, Margit A1 - Bäßler, Ralph T1 - Compatibility of polymers exposed to heating oil blends with 10 % and 20 % biodiesel (FAME) N2 - Biodiesel (FAME) from rapeseed is an environmentally friendly alternative to common fossil fuels. It is also suitable to serve as blending component to fuels like heating oil. If the fuel composition is changed, materials compatibility must be guaranteed. Adding polar biodiesel to nonpolar heating oil, changes the blend’s solvency and might cause swelling, extraction and solvation of polymers. The objective of this research was to investigate the compatibility of polymeric materials, which are commonly used for components in middle distillate facilities, along with blends of heating oil and 20 % biodiesel (B20). For this propose, ACM, HNBR, FKM, PE, PA 6, POM, PUR and PVC were exposed to heating oil and B20 for 42 and 84 days at 40 °C. In addition, the polymers HNBR, FKM, PA, POM and PVC were also exposed at 70 °C. Furthermore, the resistance of polymers in eight-year aged B10 at 40 °C was evaluated. Ageing of biodiesel increases acidity which might propagate polymer corrosion. The materials were evaluated as resistant, if the loss in tensile properties (tensile strength and elongation at break) and Shore hardness remained under 15 % compared to the initial unexposed material values. For investigations under compressed conditions, the compression set was determined for specimens of ACM, FKM and HNBR after exposure in heating oil B0 and B20 for 3,7,14, 28, 56 and 90 days at 40 °C according to ISO 815-1. It was found that the resistance in B20 at 40 °C was given for all tested polymers except PUR. In the 8 years aged B10, PUR and POM were not compatible and ACM just conditionally compatible. At 70 °C, FKM and PVC were resistant in B20, whereas HNBR and PA 6 were not compatible. Swelling occurred for the elastomers ACM, HNBR and PUR. T2 - AMPP Annual International Corrosion Conference 2021 CY - Online Meeting DA - 19.04.2021 KW - Biodiesel KW - FAME KW - RME KW - Polymer in fuels PY - 2021 SP - 16222-01 EP - 16222-12 CY - Houston AN - OPUS4-52499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - DGMK-Projekt 780: Entwicklung einer Prüfmethode zur Bewertung der Materialbeständigkeit von Bauteilen in Mitteldestillatanwendungen N2 - Für Bauteile (Komponenten) von Versorgungsanlagen für flüssige Brenn- und Kraftstoffe muss die Beständigkeit der metallenen Werkstoffe und Polymere nachgewiesen werden. Im Anwendungsfall von Heizöl mit 20 % biogenen Anteilen in Form von Rapsölfettsäuremethylester (FAME, Biodiesel) ist es für eine konservative Beurteilung des Korrosionssystems Werkstoff/Medium/Umgebung wichtig, die Alterungseffekte des Mediums einzubeziehen. Entwicklung eines Prüfverfahrens für die Untersuchung der Beständigkeit von metallenen Werkstoffen und Polymeren in Heizöl und Heizöl-FAME-Blends, das für eine Vorauswahl der Werkstoffe und zum Nachweis der Beständigkeit im Hinblick auf die bauaufsichtlichen Zulassungsverfahren geeignet ist. Ein Schwerpunkt wird bei den metallenen Werkstoffen auf der Erprobung von Messmethoden liegen, mit denen sich in kurzer Versuchszeit ein Korrosionsangriff detektieren lässt. Die untersuchten Werkstoffe Aluminium, Stahl 1.0037, 1.4301, Kupfer, Messing (CuZn40Pb) und Zink (ZP0410) sind in B0, B20, B100 und in 6 Jahre altem B100 beständig. Auch in einem Jahr alten B20 und in einem Jahr alten B100 sind die Werkstoffe beständig. Bei Kupfer blieb die Korrosionsrate in der Flüssigphase sowohl in B20 (0 μ m/ a) als auch in B100 (4 μ m/ a) nach einem Jahr unverändert. Für das 6 Jahre alte B100 stieg die Korrosionsrate des Kupfers an (16 μ m/a). Im Gegensatz dazu sank bei Messing die Korrosionsrate in der Flüssigphase mit dem Alter des Brennstoffs, nach einem Jahr für B20 von 4 μ m/ a auf 1 μ m/a und für B100 von 36 μ m/ a auf 6 μ m/ a, im 6 Jahre alten B100 lag die Korrosionsrate des Messings bei 0 μ m/ a. In 8 Jahre altem B10 trat bei Zink in der Flüssigphase Flächenkorrosion auf, es ist in dem Medium demnach nicht beständig. Messing zeigte örtliche Korrosion in der Gasphase, es ist folglich unbeständig und für den Einsatz in stark gealterten B10 nicht geeignet. Aluminium, 1.0037, 1.4301 und Kupfer sind in dem 8 Jahre alten B10 beständig. Die Änderung der Zugfestigkeit und der Reißdehnung von ACM, HNBR und FKM in Heizöl, B20 und gealterten B10 beträgt < 15 %. Diese Werkstoffe sind in Heizöl, B20 und in gealterten B10 unter Berücksichtigung des von der BAM zur Beurteilung der Beständigkeit festgelegten Grenzwertes von 15 % bei 40 °C als beständig zu bewerten. PUR ist bei 40 °C nicht beständig in B20 und in gealtertem B10. Bei 70 °C ist HNBR nicht in B20 beständig aufgrund der Verringerung der Zugfestigkeit (40 %) und der Reißdehnung (50 %). FKM ist bei 70 °C in Heizöl und in B20 beständig. T2 - Sitzung AK Prüfstellen CY - Berlin, Germany DA - 18.09.2019 KW - Heizöl mit 20% Biodiesel (B20) KW - Beständigkeit KW - Metallene Werkstoffe KW - Polymere Werkstoffe KW - Zugeigenschaften KW - Shore-Härte PY - 2019 AN - OPUS4-50188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Compatibility of polymers with aged heating oil containing 10 % and 20 % biodiesel under static conditions N2 - Biodiesel is viewed as a major source of energy. In areas such as the European Un-ion, where 80 % of the oil-based fuel is imported, there is also the desire to reduce dependence on external oil supplies. Materials compatibility is a major concern whenever the fuel composition is changed. The question arises of whether polymeric materials are resistant to heating oil with 20 % biodiesel (B20) in comparison to pure heating oil. The polarity of biodiesel increases its solvency and facilitates permeation and extrac-tion. Solvation, swelling and/or extraction lead to changes in the physical properties. Extraction alters the fuel chemistry. These chemical changes could also accelerate the degradation (hydrolysis and oxidation) of the polymeric material with the loss of additives and stabilizers. Exposure tests to determine the resistance of polymers frequently used for compo-nents in middle distillate facilities, such as ACM, FKM, HNBR, PA, PE, POM, PUR and PVC in heating oil and a blend of heating oil and 20 % biodiesel (B20) were al-ready performed. The objective of this research was to determine the resistance of these polymers in 8-year aged heating oil blend B10 and 1-year aged blend B20 at 40 °C. Mass, tensile strength, breaking elongation and Shore hardness A (D) of the test specimens were determined before and after exposure for 84 (42) days in the test fuels under static conditions. There is not determined a threshold for the reduction in tensile properties and Shore hardness in the international standards. Therefore, a threshold of 15 % was deter-mined for the evaluation of the compatibility. A significant reduction in Shore hardness was determined after exposure of ACM and PUR test specimens in 1-year aged B20. The tensile strength of PUR test specimens in 1-year aged B20 was reduced by more than 50 %, and the breaking elongation by more than 30 %. A decrease in breaking elongation was measured for POM test specimens after ex-posure to 1-year aged B20 by 25 % (limited resistance). 8-year aged B10 had a stronger effect than 1-year aged B20 on the polymers. ACM test specimens were softened by B10 resulting in a drop of Shore hardness by over 20 %. B10 reduced tensile strength and breaking elongation of PUR test specimens by over 50 %. In contrast, the breaking elongation of POM was increased by over 270 %. It can be concluded that the polymers HNBR, FKM, PA6, PE and PVC are resistant in 1-year aged B20 whereas ACM and POM are limited resistant. PUR is not re-sistant. HNBR, FKM, PA6, PE and PVC are resistant in 8-year aged B10, whereas PUR and POM are not resistant, and ACM just limited resistant. T2 - EUROCORR 2020 CY - Online meeting DA - 07.09.2020 KW - Aged heating oil with 10% and 20% biodiesel KW - Resistance of polymers KW - Tensile properties KW - Shore hardness PY - 2020 AN - OPUS4-51240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Bewertung de Beständigkeit von metallischen Werkstoffen und polymeren Dichtungswerkstoffen unter dem Einfluss von Biokraftstoffen T2 - Beiratssitzung des Normenausschusses Tankanlagen im DIN CY - DIN Berlin DA - 2014-11-06 PY - 2014 AN - OPUS4-31924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -