TY - JOUR
A1 - You, Zengchao
A1 - Meier, Florian
A1 - Weidner, Steffen
ED - Weidner, Steffen
T1 - Comparison of miniaturized and conventional asymmetrical flow field flow fractionation (AF4) channels for nanoparticle separation
N2 - The performance of a miniaturized channel for the separation of polymer and metal nanoparticles (NP) using Asymmetrical Flow Field-Flow Fractionation (AF4) was investigated and compared with a conventional AF4 system. To develop standard separation methods, experimental parameters like cross flow, gradient profile and injection time were varied and optimized.
Corresponding chromatographic parameters were calculated and compared. Our results indicate that the chromatographic resolution in the miniaturized channel is lower, whereas significantly shorter analyses time and less solvent consumption were obtained. Moreover, the limit of detection (LOD) and limit of quantification (LOQ) obtained from hyphenation with a UV-detector are obviously lower than in a conventional channel, which makes the miniaturized channel interesting for trace analysis.
KW - Nanoparticles separation asymetrical flow field flow fractionation
PY - 2017
DO - https://doi.org/10.3390/separations4010008
SN - 2297-8739
VL - 4
IS - 1
SP - 8, 1
EP - 11
AN - OPUS4-47196
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gabriel, Stefan
A1 - Schwarzinger, C.
A1 - Schwarzinger, B.
A1 - Panne, Ulrich
A1 - Weidner, Steffen
T1 - Matrix segregation as the major cause for sample inhomogeneity in MALDI dried droplet spots
N2 - The segregation in dried droplet MALDI sample spots was analyzed with regard to the matrix-to-sample ratio using optical microscopy, MALDI imaging mass spectrometry (MALDI MSI) and IR imaging spectroscopy. In this context, different polymer/matrix/solvent systems usually applied in the analysis of synthetic polymers were investigated. The use of typical matrix concentrations (10 mg mL-1) in almost every case resulted in ring patterns, whereas higher concentrated matrix solutions always led to homogeneous sample spot layers. The data revealed that segregation is predominantly caused by matrix transport in the drying droplet, whereas polymer segregation seems to be only secondary.
KW - MALDI
KW - Imaging MS
KW - Matrix segregation
KW - Dried droplet
KW - Sample preparation
KW - Polymers
PY - 2014
DO - https://doi.org/10.1007/s13361-014-0913-0
SN - 1044-0305
VL - 25
IS - 8
SP - 1356
EP - 1363
PB - American Society for Mass Spectrometry
CY - New York, NY
AN - OPUS4-32582
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, Hans
A1 - Weidner, Steffen
T1 - High molar mass cyclic poly(L-lactide) via ring-expansion polymerizationwith cyclic dibutyltin bisphenoxides
N2 - Two new catalysts (SnNa and SnBi) were prepared from dibutyltin oxide and 2,2′-dihydroxybiphenyl or2,2′dihydroxy(1,1′-binaphtyl). These catalysts enabled rapid polymerizations of L-lactide at 160 or 180 °C in bulk, whereby almost exclusively cyclic polylactides were formed. These polymerizations were free of racemization and yielded pol(L-lactide)s having weight average molecular weights (Mw's) up to 140 000 g mol−1. The Mw's varied little with the Lac/Cat ratio as expected for a ring expansion polymerization (REP). Polymerizations performed in bulk at 140, 120 and 102 °C yielded cyclic polylactides with lower molecular weights. At 102 °C a strong predominance of even-numbered cycles was found with SnNa as catalyst. SnNa can also catalyze alcohol-initiated ROPs yielding linear poly(L-lactide) free of cyclics.
KW - MALDI-TOF MS
KW - Polylactide
KW - Ring-opening Polymerization
KW - Cyclization
KW - Catalysts
PY - 2018
DO - https://doi.org/10.1016/j.eurpolymj.2018.05.036
SN - 0014-3057
SN - 1873-1945
VL - 105
SP - 158
EP - 166
PB - Elsevier Ltd.
AN - OPUS4-45439
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Jlalia, I.
A1 - Chabbah, T.
A1 - Chatti, S.
A1 - Schiets, F.
A1 - Casabianca, H.
A1 - Marestin, C.
A1 - Mercier, R.
A1 - Weidner, Steffen
A1 - Kricheldorf, H. R.
A1 - Errachid, A.
A1 - Vulliet, E.
A1 - Hammani, M.
A1 - Jaffrezic-Renault, N.
T1 - Alternating bio-based pyridinic copolymers modified with hydrophilic and hydrophobic spacers as sorbents of aromatic pollutants
N2 - The main objective of this work was to design new advanced sorbent phases, alternating copolymers, derived from isosorbide and 2,6-difluorpyridine, to be used for the removal of aromatic organic pollutants present in water at low concentrations. Six different monomers, dianhydrohexitols isomers and bisphenol derivatives, weresynthesized in order to make it possible to study their hydrophilic and hydrophobiceffect on the sorption efficiency of the resulting polymeric phases. Before this study, we have confirmed the chemicals structures, molecular weights, and thermal properties of the obtained polymeric phases. Sorption results show a higher adsorption efficiency of P6 co-poly(ether-pyridine) based on bisphenol substituted with pyridineunits, for all tested pollutants, hydrophobic and hydrophilic ones, due to its less compact structure. Two aromatic organic pollutants, p-hydroxybenzoic acid and toluicacid, were selected as sorbates to study the adsorption characteristic, kinetics and isotherms of the copoly(ether pyridine) P6. Langmuir model led to a better fitting of the sorption isotherms; the sorption of toluic acid is easier than of that p-hydroxybenzoic acid. Comparing 1/n values for benzoic acid was two time lower for P6 compared to that for biochar and for crosslinked methacrylate resin, showing a higher efficiency
KW - Alternating co-poly(ether pyridine)s
KW - Aromatic organic compounds,
KW - Biosourced isosorbide
KW - Sorption isotherm
KW - Sorption mechanism
PY - 2021
DO - https://doi.org/10.1002/pat.5578
VL - 33
IS - 4
SP - 1057
EP - 1068
PB - Wiley Online Library
AN - OPUS4-54031
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Koshkina, Olga
A1 - Lang, Thomas
A1 - Thiermann, R.
A1 - Docter, D.
A1 - Stauber, R.H.
A1 - Secker, C.
A1 - Schlaad, H.
A1 - Weidner, Steffen
A1 - Mohr, B.
A1 - Maskos, M.
A1 - Bertin, Annabelle
T1 - Temperature-triggered protein adsorption on polymer-coated nanoparticles in serum
N2 - The protein corona, which forms on the nanoparticle's surface in most biological media, determines the nanoparticles physicochemical characteristics. The formation of the protein corona has a significant impact on the biodistribution and clearance of nanoparticles in vivo. Therefore, the ability to influence the formation of the protein corona is essential to most biomedical applications, including drug delivery and imaging. In this study, we investigate the protein adsorption on nanoparticles with a hydrodynamic radius of 30 nm and a coating of thermoresponsive poly(2-isopropyl-2-oxazoline) in serum. Using multiangle dynamic light scattering (DLS) we demonstrate that heating of the nanoparticles above their phase separation temperature induces the formation of agglomerates, with a hydrodynamic radius of 1 µm. In serum, noticeably stronger agglomeration occurs at lower temperatures compared to serum-free conditions. Cryogenic transmission electron microscopy (cryo-TEM) revealed a high packing density of agglomerates when serum was not present. In contrast, in the presence of serum, agglomerated nanoparticles were loosely packed, indicating that proteins are intercalated between them. Moreover, an increase in protein content is observed upon heating, confirming that protein adsorption is induced by the alteration of the surface during phase separation. After cooling and switching the surface back, most of the agglomerates were dissolved and the main fraction returned to the original size of approximately 30 nm as shown by asymmetrical flow-field flow fractionation (AF-FFF) and DLS. Furthermore, the amounts of adsorbed proteins are similar before and after heating the nanoparticles to above their phase-separation temperature. Overall, our results demonstrate that the thermoresponsivity of the polymer coating enables turning the corona formation on nanoparticles on and off in situ. As the local heating of body areas can be easily done in vivo, the thermoresponsive coating could potentially be used to induce the agglomeration of nanoparticles and proteins and the accumulation of nanoparticles in a targeted body region.
PY - 2015
DO - https://doi.org/10.1021/acs.langmuir.5b00537
SN - 0743-7463
SN - 1520-5827
VL - 31
IS - 32
SP - 8873
EP - 8881
PB - American Chemical Society
CY - Washington, DC
AN - OPUS4-34163
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Leiterer, Jork
A1 - Panne, Ulrich
A1 - Thünemann, Andreas
A1 - Weidner, Steffen
T1 - Container-less polymerization in acoustically levitated droplets: an analytical study by GPC and MALDI-TOF mass spectrometry
N2 - Molecular masses and end groups of polystyrene (PS) formed in a novel container-less polymerization strategy, based on levitated droplets in an acoustic trap, were determined by Gel Permeation Chromatography (GPC) and Matrix-assisted Laser Desorption/Ionization Time of Flight Mass spectrometry (MALDI-TOF MS).
KW - Ultraschallfalle
KW - MALDI Massenspektrometrie
KW - Polymerisation
PY - 2011
DO - https://doi.org/10.1039/c0ay00390e
SN - 1759-9660
SN - 1759-9679
VL - 3
IS - 1
SP - 70
EP - 73
PB - RSC Publ.
CY - Cambridge
AN - OPUS4-23655
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, Hans R.
A1 - Weidner, Steffen
A1 - Scheliga, Felix
T1 - Cyclic poly(l-lactide) via ring-expansion polymerization by means of dibutyltin 4-tert-butylcatecholate
N2 - Five new catalysts are prepared from dibutyltin oxide and catechol (HCa),
2,3-dihydroxynaphthalene (NaCa), 4-tert-butyl catechol (BuCa), 4-cyano
catechol (CyCa), and 4-benzoyl catechol (BzCa), but only BuCa gives useful
results. When benzyl alcohol is used as an initiator, linear chains having
benzyl ester end groups are formed in a slow polymerization process. In
contrast to cyclic or noncyclic dibutyltin bisalkoxides, neat BuCa yields
cyclic poly(l-lactide)s via a fast ring-expansion polymerization. Under certain
conditions, a high-melting crystalline phase (Tm = 191 °C) is obtained.
At 160 °C and short reaction times even-numbered cycles are slightly
prevailing, but, surprisingly, at 120 °C, odd-numbered cycles are predominantly
formed. These results definitely prove that a ring-expansion mechanism
is operating.
KW - Lactides
KW - MALDI TOF MS
KW - Morphology
KW - Ring-opening polymerization
KW - Tin catalysts
PY - 2017
DO - https://doi.org/10.1002/macp.201700274
SN - 1521-3935
SN - 1022-1352
VL - 218
IS - 22
SP - 1700274, 1
EP - 1700274, 10
PB - Wiley VCH
CY - Weinheim
AN - OPUS4-43583
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Weidner, Steffen
T1 - Cyclic polylactides via ring-expansion polymerization
N2 - We will report on a new kind of ring-expansion polymerization (REP) of cyclic esters based of three classes of catalysts.
In contrast to REP described previously these new polymerizations are characterized by a self-extrusion of the catalysts resulting in cyclic homopolyesters as the only reaction product. These REP of L-lactide were performed in bulk at temperatures between 100 and 180°C without racemization. A simplified scheme of a REP catalyzed by BuCa or SnBi is presented below. With meso-lactide temperatures down to 60°C were realized. Depending on catalyst, time and temperature with equal quantities of even and odd-numbered cycles a strong predominance of either even or odd-numbered cycles was found.
T2 - 255th ACS National Meeting
CY - New Orleans, LA, USA
DA - 18.03.2018
KW - MALDI-TOF MS
KW - Poly(lactide)
KW - Polymerisation
KW - Catalysts
PY - 2018
AN - OPUS4-44833
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Scheliga, F.
A1 - Kricheldorf, H.R.
T1 - Low-temperature polymerization of epsilon-caprolactone catalyzed by cerium triflates
N2 - Using 22 metal triflates as catalysts, ε-caprolactone is polymerized at 22 °C in bulk. Only five relatively acidic triflates prove active. Three triflates, including the neutral Sm3+, are active using water as initiator. A very low content of cyclics is found in all the experiments. With Ce3+ and Ce4+, polymerizations are performed in CH2Cl2 and in bulk at 2 °C and 22 °C. Low dispersities (down to 1.1) are obtained. At 22 °C, Ce4+ and, even better, Ce3+ also catalyze syntheses of CO2H- and CH2OH-terminated polycaprolactones, whereby higher dispersities and larger fractions of cyclics are obtained. Further polymerizations and polycondensations are catalyzed with protic acids. The results can be explained by a proton-catalyzed activated monomer mechanism.
KW - Epsilon-caprolactone
KW - Cyclization
KW - Metal triflates
KW - Polycondensation
KW - Ring-opening polymerization
PY - 2013
DO - https://doi.org/10.1002/macp.201300279
SN - 1022-1352
SN - 1521-3935
VL - 214
IS - 18
SP - 2043
EP - 2053
PB - Wiley-VCH Verl.
CY - Weinheim
AN - OPUS4-29219
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Schultze, R.-D.
A1 - Enthaler, B.
T1 - Matrix-assisted laser desorption/ionization imaging mass spectrometry of pollen grains and their mixtures
N2 - RATIONALE
The fast and univocal identification of different species in mixtures of pollen grains is still a challenge. Apart from microscopic evaluation and Raman spectroscopy, no other techniques are available.
METHODS
Matrix-assisted laser desorption/ionization (MALDI) imaging mass spectrometry was applied to the analysis of extracts of single pollen grains and pollen mixtures. Pollen grains were fixed, treated and covered with matrix directly on the MALDI target.
RESULTS
Clearly resolved MALDI ion intensity images could be obtained enabling the identification of single pollen grains in a mixture.
CONCLUSIONS
Our results demonstrate the potential and the suitability of MALDI imaging mass spectrometry as an additional method for the identification of pollen mixtures.
KW - MALDI
KW - Imaging
KW - Pollen
KW - Blends
PY - 2013
DO - https://doi.org/10.1002/rcm.6523
SN - 0951-4198
SN - 1097-0231
VL - 27
IS - 8
SP - 896
EP - 903
PB - Wiley
CY - Chichester
AN - OPUS4-27986
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Holländer, A.
A1 - Kühn, Gerhard
T1 - Matrix-assisted Laser Desorption/Ionization Mass Spectrometry of C36- Alkane degradated by Vacuum Ultraviolet Radiation
PY - 1997
SN - 0951-4198
SN - 1097-0231
VL - 11
SP - 447
EP - 450
PB - Wiley
CY - Chichester
AN - OPUS4-11095
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gabriel, Stefan
A1 - Steinhoff, R.F.
A1 - Pabst, M.
A1 - Schwarzinger, C.
A1 - Zenobi, R.
A1 - Panne, Ulrich
A1 - Weidner, Steffen
T1 - Improved analysis of ultra-high molecular mass polystyrenes in matrix-assisted laser desorption/ionization time-of-flight mass spectrometry using DCTB matrix and caesium salts
N2 - Rationale
The ionization of polystyrenes in matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) is typically achieved by the use of silver salts. Since silver salts can cause severe problems, such as cluster formation, fragmentation of polymer chains and end group cleavage, their substitution by alkali salts is highly desirable.
Methods
The influence of various cations (Ag+, Cs+ and Rb+) on the MALDI process of polystyrene (PS) mixtures and high mass polystyrenes was examined. The sample preparation was kept as straightforward as possible. Consequently, no recrystallization or other cleaning procedures were applied.
Results
The investigation of a polystyrene mixture showed that higher molecular polystyrenes could be more easily ionized using caesium, rather than rubidium or silver salts. In combination with the use of DCTB as matrix a high-mass polymer analysis could be achieved, which was demonstrated by the detection of a 1.1 MDa PS.
Conclusions
A fast, simple and robust MALDI sample preparation method for the analysis of ultra-high molecular weight polystyrenes based on the use of DCTB and caesium salts has been presented. The suitability of the presented method has been validated by using different mass spectrometers and detectors.
KW - MALDI
KW - Mega-dalton
KW - Ionization
KW - Caesium
KW - Polystyrene
KW - DCTB
PY - 2015
UR - http://onlinelibrary.wiley.com/doi/10.1002/rcm.7197/full
DO - https://doi.org/10.1002/rcm.7197
SN - 0951-4198
SN - 1097-0231
VL - 29
IS - 11
SP - 1039
EP - 1046
PB - Wiley
CY - Chichester
AN - OPUS4-33191
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Trimpin, Sarah
A1 - Yenchick, Frank S.
A1 - Lee, Chuping
A1 - Hoang, Khoa
A1 - Pophristic, Milan
A1 - Karki, Santosh
A1 - Marshall, Darrell D.
A1 - Lu, I-Chung
A1 - Lutomski, Corinne A.
A1 - El-Baba, Tarick J.
A1 - Wang, Beixi
A1 - Pagnotti, Vincent S.
A1 - Meher, Anil K.
A1 - Chakrabarty, Shubhashis
A1 - Imperial, Lorelei F.
A1 - Madarshahian, Sara
A1 - Richards, Alicia L.
A1 - Lietz, Christopher B.
A1 - Moreno-Pedraza, Abigail
A1 - Leach, Samantha M.
A1 - Gibson, Stephen C.
A1 - Elia, Efstathios A.
A1 - Thawoos, Shameemah M.
A1 - Woodall, Daniel W.
A1 - Jarois, Dean R.
A1 - Davis, Eric T.J.
A1 - Liao, Guochao
A1 - Muthunayake, Nisansala S.
A1 - Redding, McKenna J.
A1 - Reynolds, Christian A.
A1 - Anthony, Thilani M.
A1 - Vithanarachchi, Sashiprabha M.
A1 - DeMent, Paul
A1 - Adewale, Adeleye O.
A1 - Yan, Lu
A1 - Wager-Miller, James
A1 - Ahn, Young-Hoon
A1 - Sanderson, Thomas H.
A1 - Przyklenk, Karin
A1 - Greenberg, Miriam L.
A1 - Suits, Arthur G.
A1 - Allen, Matthew J.
A1 - Narayan, Srinivas B.
A1 - Caruso, Joseph A.
A1 - Stemmer, Paul M.
A1 - Nguyen, Hien M.
A1 - Weidner, Steffen
A1 - Rackers, Kevin J.
A1 - Djuric, Ana
A1 - Shulaev, Vladimir
A1 - Hendrickson, Tamara L.
A1 - Chow, Christine S.
A1 - Pflum, Mary Kay H.
A1 - Grayson, Scott M.
A1 - Lobodin, Vladislav V.
A1 - Guo, Zhongwu
A1 - Ni, Chi-Kung
A1 - Walker, J. Michael
A1 - Mackie, Ken
A1 - Inutan, Ellen D.
A1 - McEwen, Charles N.
T1 - New Processes for Ionizing Nonvolatile Compounds in Mass Spectrometry: The Road of Discovery to Current State-of-the-Art
N2 - This Perspective covers discovery and mechanistic aspects aswell as initial applications of novel ionization processes for use in massspectrometry that guided us in a series of subsequent discoveries, instrumentdevelopments, and commercialization. Vacuum matrix-assisted ionization onan intermediate pressure matrix-assisted laser desorption/ionization sourcewithout the use of a laser, high voltages, or any other added energy wassimply unbelievable, at first. Individually and as a whole, the variousdiscoveries and inventions started to paint, inter alia, an exciting new pictureand outlook in mass spectrometry from which key developments grew thatwere at the time unimaginable, and continue to surprise us in its simplisticpreeminence. We, and others, have demonstrated exceptional analyticalutility. Our current research is focused on how best to understand, improve, and use these novel ionization processes throughdedicated platforms and source developments. These ionization processes convert volatile and nonvolatile compounds from solid orliquid matrixes into gas-phase ions for analysis by mass spectrometry using, e.g., mass-selected fragmentation and ion mobilityspectrometry to provide accurate, and sometimes improved, mass and drift time resolution. The combination of research anddiscoveries demonstrated multiple advantages of the new ionization processes and established the basis of the successes that lead tothe Biemann Medal and this Perspective. How the new ionization processes relate to traditional ionization is also presented, as wellas how these technologies can be utilized in tandem through instrument modification and implementation to increase coverage ofcomplex materials through complementary strengths.
KW - Mass spectrometry
PY - 2024
DO - https://doi.org/10.1021/jasms.3c00122
SN - 1879-1123
VL - 35
IS - 12
SP - 2753
EP - 2784
PB - American Chemical Society (ACS)
AN - OPUS4-61417
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Kricheldorf, H. R.
T1 - The Role of Transesterification in SnOct 2 - Catalyzed Polymerizations of Lactides
N2 - l-lactide or meso-lactide are polymerized either at 120 °C where the polymerization process of l-lactide is accompanied by crystallization, or at 180 °C where poly(l-lactide) remains in the molten state. Polymerizations at 120 °C initially yield even-numbered chains (with respect to lactic acid units) having relatively low dispersity, but the fraction of odd-numbered chains increases with time and the entire molecular weight distribution changes. Traces of cyclics are only formed after 7 d. Polymerizations at 180 °C yield equilibrium of even and odd-numbered chains from the beginning, but at low monomer/initiator ratios and short reaction times (<4 h) cyclics are again not formed. They appear at longer reaction times and entail higher dispersities. The results are discussed in terms of five different transesterification mechanisms.
KW - Polylactides
KW - MALDI
KW - Transesterification
KW - Sn catalysts
PY - 2017
DO - https://doi.org/10.1002/macp.201600331
SN - 1022-1352
VL - 218
IS - 3
SP - 1600331
PB - Wiley
AN - OPUS4-39753
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Rösler, Alexander
A1 - Weidner, Steffen
A1 - Klamroth, Tillmann
A1 - Müller, Axel H. E.
A1 - Schlaad, Helmut
T1 - Kinetics of anionic polymerization of β‐myrcene in hydrocarbon solvents
N2 - The kinetics of anionic polymerization of β‐myrcene initiated by sec‐butyllithium were examined in saturated and unsaturated hydrocarbon solvents, i.e. cyclohexane, cyclohexene, 4‐vinylcyclohexene and dl‐limonene. Polymerizations usually proceeded in a living manner, i.e. in the absence of termination and chain transfer reactions, in all solvents, to produce well‐defined polymyrcenes with high content (85%) of cis‐1,4 units. However, polymyrcenyllithium chains exhibited limited long‐term stability in 4‐vinylcyclohexene solution, most probably due to chain transfer to solvent. Reaction orders with respect to the concentration of active chains were found to be one‐quarter in cyclohexane increasing to one‐half in unsaturated solvents, indicating that the polymyrcenyllithium chains are present as tetrameric or dimeric associates, respectively. Apparent activation energies were found to be 81 kJ mol−1 in cyclohexane and 77 kJ mol−1 in dl‐limonene solution, which are close to the values obtained by quantum chemical calculations.
KW - MALDI-TOF MS
KW - Anionic polymerization
KW - β‐myrcene
KW - Kinetics
KW - Reaction order
KW - Activation energy
KW - Microstructure
KW - Quantum chemical calculations
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630900
DO - https://doi.org/10.1002/pi.6772
SN - 1097-0126
SP - 1
EP - 8
PB - Wiley
CY - New York, NY
AN - OPUS4-63090
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, Hans R.
A1 - Weidner, Steffen
T1 - Zwitterionic polymerization of glycolide catalyzed by pyridine
N2 - The usefulness of various N- and P-based catalysts for syntheses of cyclic polyglycolide via zwitterionic polymerization of glycolide was examined. Most catalysts produced discolored, largely insoluble polyglycolides consisting of cycles and unidentified byproducts. Soluble, cyclic polyglycolides were obtained using neat pyridine as catalyst at 120 °C, 100 °C, 80 °C, and even at 60 °C. The number-average molecular weights were extremely low and depended slightly on the glycolide-to-pyridine ratio. Three different mass distributions of the cycles were detected by mass spectrometry, depending on the reaction conditions. The cyclic polyglycolides were also characterized by differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS) measurements. The SAXS data in combination with the mass spectra indicate that the majority of the cycles form extended-ring crystallites
KW - MALDI-TOF MS
KW - Polylactide
KW - Polymerization
KW - Zitterions
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639748
DO - https://doi.org/10.1039/d5py00762c
SN - 1759-9954
SP - 1
EP - 9
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-63974
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, Hans R.
A1 - Weidner, Steffen
A1 - Meyer, Andreas
T1 - Poly(butylene terephthalate): About condensation, cyclization, degradation and elimination reactions in the solid state, and the role of smooth crystal surfaces
N2 - Three commercial poly(butylene terephthalate) (PBT) samples - Pocan B1300 (B13), Pocan B1600 (B16), and Addigy P 1210 (AP121) - served as the starting materials for the annealing experiments, which were conducted with and without the addition of esterification and transesterification catalysts. The catalysts used were Sn(II) 2-ethylhexanoate (SnOct₂), Zr(IV) acetylacetonate, and 4-toluene sulfonic acid (TSA). Temperatures varied between 150 and 210 °C. The PBT samples were characterized using differential scanning calorimetry (DSC), gel permeation chromatography (GPC), small-angle X-ray scattering (SAXS), and matrix-assisted laser desorption/ionization time-of-flight (MALDI TOF) mass spectrometry. The MALDI mass spectra of all three samples differed greatly but displayed mass peaks of cycles. Similar results were produced by annealing with SnOct₂ or Zr(acac)₄, which favored the formation of even-numbered cycles within the mass range below m/z 5000, along with slow degradation. TSA favored a more intensive degradation without the formation of cycles or even with the destruction of cycles. PBT chains with two carboxylic (COOH) end groups were the most stable species under all circumstances. The origin of the extremely high melting point of AP121 (241–242 °C) can be explained by the smoothing of crystallite surfaces via transesterification. The results suggest that combining MALDI mass spectrometry and SAXS measurements provides a new way to better understand the solid-state chemistry of PBT and related polyesters.
KW - MALDI-TOF MS
KW - Polybutylene Terephthalate
KW - Crystallization
KW - solid state
KW - cyclization
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652844
DO - https://doi.org/10.1016/j.polymdegradstab.2025.111862
SN - 0141-3910
VL - 245
SP - 1
EP - 11
PB - Elsevier Ltd.
AN - OPUS4-65284
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dalgic, Mete‐Sungur
A1 - Kumar, Sourabh
A1 - Weidner, Steffen
T1 - Quantitative Analysis of Polymers by MALDI‐TOF Mass Spectrometry: Correlation Between Signal Intensity and Arm Number
N2 - The signal intensities of linear and star‐shaped poly(L‐lactides) (PLA) and poly (ethylene oxides) (PEO) were compared to determine the influence of the number of arms on the ionization in matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectrometry. In this study, a variety of blends were prepared and investigated, including binary and ternary combinations of linear and star‐shaped polymers with similar molecular masses. The focus was on examining their intensity ratios. In equimolar binary PLA blends, polymer stars were observed to exhibit higher intensities than their linear counterparts. This result was supported by experiments with equimolar ternary PLA blends, which clearly demonstrated an intensity dependence on the number of polymer arms. It was observed that four‐arm PLA exhibited higher intensities than three‐arm PLA. A similar trend was observed in investigations involving acetylated polymer end groups, suggesting that differences in ionization are primarily influenced by polymer architecture rather than end groups. In order to validate this assumption, the binding energies for [polymer‐K] + adduct ions utilizing the most stable geometry obtained from GOAT (Global Optimizer Algorithm) were calculated, revealing that star‐shaped lower mass oligomers have slightly higher binding energies.
KW - MALDI-TOF MS
KW - Starlike polymers
KW - Quantification
KW - Topology
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-653401
DO - https://doi.org/10.1002/jms.70023
SN - 1076-5174
VL - 61
IS - 1
SP - 1
EP - 12
PB - John Wiley & Sons Ltd.
AN - OPUS4-65340
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Rösler, Alexander
A1 - Weidner, Steffen
A1 - Klamroth, Tillmann
A1 - Müller, Axel HE
A1 - Schlaad, Helmut
T1 - Kinetics of anionic polymerization of β‐myrcene in hydrocarbon solvents
N2 - AbstractThe kinetics of anionic polymerization of β‐myrcene initiated by sec‐butyllithium were examined in saturated and unsaturated hydrocarbon solvents, i.e. cyclohexane, cyclohexene, 4‐vinylcyclohexene and dl‐limonene. Polymerizations usually proceeded in a living manner, i.e. in the absence of termination and chain transfer reactions, in all solvents, to produce well‐defined polymyrcenes with high content (85%) of cis‐1,4 units. However, polymyrcenyllithium chains exhibited limited long‐term stability in 4‐vinylcyclohexene solution, most probably due to chain transfer to solvent. Reaction orders with respect to the concentration of active chains were found to be one‐quarter in cyclohexane increasing to one‐half in unsaturated solvents, indicating that the polymyrcenyllithium chains are present as tetrameric or dimeric associates, respectively. Apparent activation energies were found to be 81 kJ mol−1 in cyclohexane and 77 kJ mol−1 in dl‐limonene solution, which are close to the values obtained by quantum chemical calculations. © 2025 The Author(s). Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.
KW - Myrcene
KW - Anionic polymerization
KW - MALDI TOF MS
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-649039
DO - https://doi.org/10.1002/pi.6772
SN - 0959-8103
SP - 1
EP - 8
PB - Wiley
AN - OPUS4-64903
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Trimpin, S.
A1 - Lee, C.
A1 - Weidner, Steffen
A1 - El-Baba, T.
A1 - Lutomski, C.
A1 - Inutan, E.
A1 - Foley, C.
A1 - Ni, C.-K.
A1 - McEwen, C.
T1 - Unprecedented Ionization Processes in Mass SpectrometryProvide Missing Link between ESI and MALDI
N2 - In the field of mass spectrometry,producing intact, highly-charged protein ions from surfaces is a conundrum with significant potential payoff in application areas ranging from bio-medical to clinical research. Here, we report on the ability to form intact, highly-charged protein ions on high vacuum time-of-flight mass spectrometers in the linear and reflectron modes achievable using experimental conditions that allow effective matrix removal from both the sample surfaces and from the charged clusters formed by the laser Ablation event. The charge states are the highest reported on high vacuum mass spectrometers, yet they remain at only around athird of the highest charge obtained using laser ablation with a suitable matrix at atmospheric pressure. Other than physical instrument modifications, the key to forming abundant and stable highly-charged ions appears to be the volatility of the matrix used. Cumulative results suggest mechanistic links between the ionization process reported here and traditional ionization methods of electrospray ionization and matrix-assisted laser desorp-tion/ionization.
KW - MALDI
KW - Electrospray
KW - Mass spectrometry
KW - Ionization
PY - 2018
DO - https://doi.org/10.1002/cphc.201701246
SN - 1439-4235
SN - 1439-7641
VL - 19
IS - 5
SP - 581
EP - 589
PB - Wiley-VCH
AN - OPUS4-44404
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H.
A1 - Weidner, Steffen
A1 - Scheliga, F.
T1 - Cyclic poly(lactide)s via the ROPPOC method catalyzed by alkyl- or aryltin chlorides
N2 - A comparison of tributyltin chloride, dibutyltin dichloride,and butyltin trichloride as catalysts of ring-opening polymerizations(ROPs) of l-lactides at 160°C in bulk reveals increasing reactivity in the above order, but only the least reactive catalysts, Bu3SnCl, yield a uniform reaction product, namely cyclic poly(L-lactide)s with weight average molecular weights (Mw ́s) in the range of 40,000–80,000. A comparison of dimethyltin , dibutyltin , and diphenyltin dichlorides resulted in the following order of reactivity: Me2SnCl2 189 °C was monitored by means of DSC measurements and characterized in selected cases by SAXS measurements. It was confirmed that the formation of HTm crystallites involves a significant growth of the thickness of the lamellar crystallites along with smoothing of their surface. Annealing at 170 °C for 1 d or longer causes thermal degradation with lowering of the molecular weights, a gradual transition of cyclic into linear chains and a moderate decrease of lamellar thickness. An unexpected result revealed by MALDI TOF mass spectrometry is a partial reorganization of the molecular weight distribution driven by a gain of crystallization enthalpy.
KW - Polylactide
KW - MALDI-TOF MS
KW - Crystallization
KW - Annealing
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-521062
DO - https://doi.org/10.1039/d0ra10012a
VL - 11
IS - 5
SP - 2872
EP - 2883
PB - Royal Society of Chemistry
AN - OPUS4-52106
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Meyer, A.
T1 - High Tm linear poly(L-lactide)s prepared via alcohol-initiated ROPs of L-lactide
N2 - Alcohol-initiated ROPs of L-lactide were performed in bulk at 160 °C for 72 h with variation of the catalyst or with variation of the initiator (aliphatic alcohols). Spontaneous crystallization was only observed when cyclic Sn(II) compounds were used as a catalyst. Regardless of initiator, high melting crystallites with melting temperatures (Tm) of 189–193 °C were obtained in almost all experiments with Sn(II) 2,2′-dioxybiphenyl (SnBiph) as catalyst, even when the time was shortened to 24 h. These HTm poly(lactide)s represent the thermodynamically most stable form of poly(L-lactide). Regardless of the reaction conditions, such high melting crystallites were never obtained when Sn(II) 2-ethylhexanoate (SnOct2) was used as catalyst. SAXS measurements evidenced that formation of HTm poly(L-lactide) involves growth of the crystallite thickness, but chemical modification of the crystallite surface (smoothing) seems to be of greater importance. A hypothesis, why the “surface smoothing” is more effective for crystallites of linear chains than for crystallites composed of cycles is discussed.
KW - Polylactide
KW - MALDI-TOF MS
KW - Ring-opening polymerization
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-524330
DO - https://doi.org/10.1039/d1ra01990b
VL - 11
IS - 23
SP - 14093
EP - 14102
PB - Royal Society of Chemistry
AN - OPUS4-52433
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Meyer, A.
A1 - Weidner, Steffen
T1 - High Tm Poly(l-lactide)s by Means of Bismuth Catalysts?
N2 - One series of BiSub-catalyzed ring-opening polymerizations (ROPs) is per-formed at 160 °C for 3 days with addition of difunctional cocatalysts to find out, if poly(l-lactide) crystallizes directly from the reaction mixture. An analogous series is performed with monofunctional cocatalysts. High Tm crystal-lites (Tm > 190 °C) are obtained from all bifunctional cocatalysts, but not from all monofunctional ones. It is shown by means of SAXS measurements that the high Tm values are mainly a consequence of a transesterification–homogenization process across the lamellar surfaces resulting in thickness and smoothing of the surfaces. An unusual enthalpy-driven modification of the molecular weight distribution is found for samples that have crystallized during the polymerization. A third series of ROPs is performed at 170 °C for 2 h followed by annealing at 120 °C (2 h) to induce crystallization. Complete transformation of the resulting low Tm crystallites (Tm < 180 °C) into the high Tm crystallites by annealing at 170 °C for 1 d is not achieved, despite variation of the cocatalyst.
KW - Polylactide
KW - MALDI-TOF MS
KW - Crystallization
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522777
DO - https://doi.org/10.1002/macp.202100019
SN - 1022-1352
VL - 222
IS - 8
SP - 19
PB - Wiley
AN - OPUS4-52277
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
T1 - ROP of L-lactide and ε-caprolactone catalyzed by tin(ii) andtin(iv) acetates–switching from COOH terminated linear chains to cycles
N2 - The catalytic potential of tin(II)acetate, tin(IV)acetate, dibutyltin-bis-acetate and dioctyl tin-bis-acetate was compared based on polymerizations of L-lactide conducted in bulk at 160 or 130°C. With SnAc2 low-Lac/Cat ratios (15/1–50/1) were studied and linear chains having one acetate and one carboxyl end group almost free of cyclics were obtained. Higher monomer/catalyst ratios and lower temperatures favored formation of cycles that reached weight average molecular weights (Mw's) between 100,000 and 2,500,000. SnAc4 yielded mixtures of cycles and linear species under all reaction conditions. Dibutyltin- and dioctyl tin bis-acetate yielded cyclic polylactides under most reaction conditions with Mw's in the range of 20,000–80,000. Ring-opening polymerizations performed with ε-caprolactone showed similar trends, but the formation of COOH-terminated linear chains was significantly more favored compared to analogous experiments with lactide. The reactivity of the acetate catalysts decreased in the following order: SnAc2> SnAc4>Bu2SnAc2~Oct2SnAc2
KW - Polylactide
KW - MALDI-TOF MS
KW - Catalyst
KW - Ring-opening polymerization
KW - Tin acetates
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-521923
DO - https://doi.org/10.1002/pol.20200866
VL - 59
IS - 5
SP - 439
EP - 450
PB - Wiley Online Library
AN - OPUS4-52192
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Scheliga, F.
A1 - Weidner, Steffen
T1 - What does conversion mean in polymer science?
N2 - The definition of the term “conversion” is discussed for a variety of polymer syntheses. It is demonstrated that in contrast to organic and inorganic chemistry several different definitions are needed in polymer science. The influence of increasing conversion on structure and topology of homo- and Copolymers is illustrated. Chain-growth polymerizations, such as radical polymerization or living anionic polymerizations of vinyl monomers, condensative chain polymerization, two and three-dimensional step-growth polymerizations, ring–ring or chain–chain equilibration and chemical modification of polymers are considered.
KW - Polymers
KW - Polymerization
KW - Conversion
KW - Polycondensation
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-523597
DO - https://doi.org/10.1002/macp.202100010
VL - 222
IS - 8
SP - 10
PB - Wiley VCH
AN - OPUS4-52359
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Kricheldorf, H. R.
T1 - SnOct2-catalyzed ROPs of L-lactide initiated by acidic OH- compounds: Switching from ROP to polycondensation and cyclization
N2 - Ring-opening polymerizations (ROPs) of L-lactide are performed in bulk at 130°C with tin(II) 2-ethylhexanoate as catalyst and various phenols of differentacidity as initiators. Crystalline polylactides having phenyl ester end groups are isolated, which are almost free of cyclics. The dispersities and molecular weights are higher than those obtained from alcohol-initiated ROPs under identical conditions. Polymerizations at 160°C yield higher molecular weights than expected from the monomer/initiator ratio and a considerable fraction of cycles. The fraction of cycles increases with higher reactivity of the ester end group indicating that the cycles are formed by end-to-end cyclization.
KW - Polylactide
KW - MALDI-TOF MS
KW - Polymerization
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540250
DO - https://doi.org/10.1002/pol.20210823
SN - 2642-4150
VL - 60
IS - 5
SP - 785
EP - 793
PB - Wiley
AN - OPUS4-54025
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
T1 - Synthesis of polylactides by means of tin catalysts
N2 - This article reviews the usefulness of tin(II) and tin(IV) salts and compounds as catalysts for the polymerization of lactides. The text is subdivided into nine parts mainly reflecting different polymerization strategies, such as ring-opening polymerization (ROP), ring-expansion polymerization (REP), ROP combined with simultaneous polycondensation (ROPPOC), various catalysts with unknown polymerization mechanisms, and polycondensation of lactic acid. Since the toxicity of tin salts and compounds is a matter of concern and frequently mentioned in numerous publications, the first section deals with facts instead of myths about the toxicity of tin salts and compounds.
KW - Polylactide
KW - MALDI-TOF MS
KW - Tin catalysts
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545050
DO - https://doi.org/10.1039/d2py00092j
SP - 1
EP - 30
PB - Royal Society for Chemistry
AN - OPUS4-54505
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Scheliga, F.
T1 - SnOct2-catalyzed and alcohol-initiated ROPS of L-lactide - Control of the molecular weight and the role of cyclization
N2 - Ring-opening polymerizations (ROP) of l-lactide (LA) are conducted in bulk at 130, 160, or 180 °C and are initiated with two different alcohols at 160 °C. The lactide/initiator ratio (LA/In) is varied from 50/1 (20/1 at 180 °C) to 900/1 and the lactide/catalyst ratio (LA/Cat) between 2000/1 and 8000/1. At all temperatures a nearly perfect control of number average molecular weight (Mn) via the LA/In ratio is feasible up to LA/In = 200/1, but at higher ratios the Mn value lags behind the theoretical values and the discrepancy increases with higher LA/Cat ratios. Variation of the LA/Cat ratio influences the formation of cycles but does not significantly influence Mn, when the LA/In ratio is kept constant. The formation of cycles is favored by lower In/Cat ratios and is the main reason for the unsatisfactory control of Mn at high LA/In ratios. The results also suggest that the cycles are mainly or exclusively formed by end-to-end cyclization and not, as believed previously, by back-biting.
KW - Polylactide
KW - MALDI-TOF MS
KW - Cyclization
KW - Ring-opening polymerization
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543066
DO - https://doi.org/10.1002/macp.202100464
SN - 1521-3935
SP - 1
EP - 10
PB - Wiley-VCH
CY - Weinheim
AN - OPUS4-54306
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Scheliga, F.
T1 - Ring-Expansion Polymerization of 𝝐-Caprolactone, Glycolide, and l-lactide with a Spirocyclic Tin(IV) Catalyst Derived from or 2,2′-Dihydroxy-1,1′-Binaphthyl – New Results and a Revision
N2 - In contrast to other cyclic tin bisphenoxides, polymerizations of glycolide and l-lactide with the spirocyclic tin(IV) bis-1,1′-bisnapthoxide yield linear chains having a 1,1′-bisnapthol end group and no cycles. In the case of l-lactide, LA/Cat ratio and temperature are varied and at 160 °C or below, all polylactides mainly consist of even-numbered chains. A total predominance of even-numbered chains is also found for homopolymerization of glycolide, or the copolymerization of glycolide and l-lactide, when conducted <120 °C.
Linear chains having a bisnaphthol end group are again the main reaction products of ring-expansion polymerizations (REP) of 𝝐-caprolactone, but above 150 °C cycles are also formed.
KW - Polylactide
KW - MALDI-TOF MS
KW - Polymerization
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-541931
DO - https://doi.org/10.1002/macp.202100308
VL - 222
IS - 24
SP - 1
EP - 10
PB - Wiley VCH GmbH
AN - OPUS4-54193
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, Hans R.
A1 - Weidner, Steffen
T1 - Ring-ring equilibration (RRE) of cyclic poly(L-lactide)s by means of cyclic tin catalysts
N2 - With 2,2-dibutyl-2-stanna-1,3-dithiolane (DSTL) and 2-stanna-1,3-dioxa-4,5,6,7-dibenzoxepane (SnBiPh) as catalysts ring-expansion polymerizations (REP) were performed either in 2 M solution using three different solvents and two different temperatures or in bulk at 140 and 120 ◦C. A kinetically controlled rapid REP up to weight average molecular masses (Mẃs) above 300 000 was followed by a slower degradation of the molecular masses at 140 ◦C, but not at 120 ◦C Furthermore, a low molecular mass cyclic poly(L-lactide) (cPLA) with a Mn around 16 000 was prepared by polymerization in dilute solution and used as starting material for ring-ring equilibration at 140 ◦C in 2 M solutions. Again, a decrease of the molecular mass was detectable, suggesting that the equilibrium Mn is below 5 000. The degradation of the molecular masses via RRE was surprisingly more effective in solid cyclic PLA than in solution, and a specific transesterification mechanism involving loops on the surface of crystallites is proposed. This degradation favored the formation of extended-ring crystallites, which were detectable by a “saw-tooth pattern” in their MALDI mass spectra.
KW - Organic Chemistry
KW - Polymers and Plastics
KW - MALDI-TOF MS
KW - Materials Chemistry
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-593819
DO - https://doi.org/10.1016/j.eurpolymj.2024.112765
SN - 0014-3057
VL - 206
SP - 1
EP - 8
PB - Elsevier B.V.
AN - OPUS4-59381
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Cappella, Brunero
A1 - Sturm, Heinz
A1 - Weidner, Steffen
T1 - Breaking polymer chains by dynamic plowing lithography
N2 - The adhesion of poly(methyl methacrylate) (PMMA) and polystyrene (PS) films, whose surface has been previously structured by dynamic plowing lithography (DPL), has been measured by means of forcedisplacement curves. The different adhesion of modified and unmodified PS leads to the assumption that polymer chains are broken during DPL. After measuring the energy dissipated by the tip during DPL, in order to check that the transferred energy is sufficient to break covalent bonds, the polymer chain scission caused by the lithographic process has been definitely confirmed by size exclusion chromatography measurements of the lithographed films.
KW - AFM
KW - Nanolithography
KW - Chain scission
PY - 2002
DO - https://doi.org/10.1016/S0032-3861(02)00285-9
SN - 0032-3861
SN - 1873-2291
VL - 43
IS - 16
SP - 4461
EP - 4466
PB - Springer
CY - Berlin
AN - OPUS4-1608
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
T1 - Dispersities of Polyesters of Various Diphenols Prepared by Irreversible Polycondensations
N2 - Polyesters of bisphenol-A, bisphenol-P, catechol, and sebacic acid are prepared and different synthetic methods are compared. The diphenols are condensed with sebacoyl chloride either in dichloromethane/pyridine or in refl uxing chlorobenzene without HCl-acceptor. Further- more, bisphenol-A acetate is polycondensed with sebacic acid in bulk. All experiments are worked up so that fractionation is avoided. The extent of cyclization is estimated by matrix-assisted laser desorption/ionization mass spectrometry (MALDI MS) and the molar mass distribution by size exclusion chromatography (SEC). Polycondensations in solution yield larger fractions of cyclics and higher dispersities (up to 11). Polycondensations in bulk give lower fractions of cycles and dispersities from 4.6 to 6.3 for high molar mass polyesters or 2.8 to 3.5 for low molar mass products. Characteristic curves describing the dependence of the dispersity on the initial monomer concentration are elaborated.
KW - cyclization
KW - dispersity
KW - mass spectra
KW - polycondensation
KW - polyesters
PY - 2016
DO - https://doi.org/10.1002/macp.201600004
IS - 217
SP - 1361
EP - 1369
PB - Wiley-VCH Verlag
CY - Weinheim
AN - OPUS4-37120
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Zeegers, G. P.
A1 - Steinhoff, R. F.
A1 - Weidner, Steffen
A1 - Zenobi, R.
T1 - Evidence for laser-induced redox reactions in matrix-assisted laserdesorption/ionization between cationizing agents and target plate material: a study with polystyrene and trifluoroacetate salts
N2 - Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) is often applied to assess the dispersity and the end groups of synthetic polymers through the addition of cationizing agents. Here weaddress how these cation adducts are formed using polystyrene (PS) as a model polymer. We analyzed PSby MALDI-MS with a 2-[(2E)-3-(4-tert-butylphenyl)-2-methylprop-2-enylidene]malononitrile (DCTB) as the matrix and a range of trifluoroacetate (TFA) salts as cationizing agents on a range of different targetplate materials (copper, 1.4301 stainless steel, aluminum, Inconel 625, Ti90/Al6/V4 and chromium-, gold-and silver-plated stainless steel). It was found that on a stainless steel substrate the metal cations Al+,Li+, Na+, Cu+and Ag+formed polystyrene adducts, whereas K+, Cs+, Ba2+, Cr3+, Pd2+, In3+, or their lower oxidation states, did not. For the copper and silver substrates, PS and DCTB adduct formation with cations liberated from these target plate materials was observed upon addition of a cationizing agent, which indicates the occurrence of redox reactions between the added TFA salts and the target plate material. Judging from their standard electrode potentials, these redox reactions would not normally occur, i.e.,they require an additional energy input, strongly suggesting that the observed redox reactions are laser-induced. Furthermore, copper granules were found to successfully sequester PS from a tetrahydrofuran(THF) solution, consistent with the view complex formation with the copper target plate can take place prior to the MALDI-MS measurement.
KW - Polymer MALDI
KW - Cationization
KW - Polystyrene
KW - Laser-induced redox reactions
KW - Target plate material
PY - 2017
DO - https://doi.org/10.1016/j.ijms.2016.10.007
SN - 1387-3806
SN - 1873-2798
VL - 416
SP - 80
EP - 89
PB - Elsevier B.V.
AN - OPUS4-41146
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Scheliga, F.
T1 - Cyclic poly(L-lactide)s via ring-expansion polymerizations catalysed by 2,2-dibutyl-2- stanna-1,3-dithiolane
N2 - L-Lactides were polymerized in bulk at 120 or 160 °C with cyclic dibutyltin catalysts derived from 1,2-dimercaptoethane or 2-mercaptoethanol. Only linear chains having one benzyl ester and one OH-end group were obtained when benzyl alcohol was added. When L-lactides were polymerized with neat dibutyl-2-stanna-1,3-dithiolane, exclusively cyclic polylactides were formed even at 120 °C. The temperature, time and monomer/catalyst ratio (M/C) were varied. These results are best explained by a combination of ring-expansion polymerization and ring-extrusion of cyclic oligo- or polylactides with Elimination of the cyclic catalyst. Neither syntheses of linear polylactides nor of cyclic lactides involved racemization up to 20 h at 160 °C.
KW - Ring-expansion polymerization
KW - MALDI
KW - Polylactides
PY - 2017
DO - https://doi.org/10.1039/C6PY02166B
SN - 1759-9954
SN - 1759-9962
VL - 8
IS - 9
SP - 1589
EP - 1596
PB - Royal Society of Chemistry
AN - OPUS4-39748
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Chabbah, T.
A1 - Chatti, S.
A1 - Jaffrezic-Renault, N.
A1 - Weidner, Steffen
A1 - Marestin, C.
A1 - Mercier, R.
T1 - Impedimetric sensors based on diethylphosphonate-containingpoly(arylene ether nitrile)s films for the detection of lead ions
N2 - This article describes the elaboration and characterization of diethylphosphonate-containing polymers coated electrodes as sensors for the detection of heavy metalstraces, by electrochemical impedance spectroscopy. Diethylphosphonate groupswere chosen as heavy metals binding sites. Two different series of polymers bearingthese anchoring groups were synthesized. Whereas the diethylphosphonate groupsare directly incorporated in the aromatic macromolecular chain in some polymers, analiphatic spacer is removing the chelating site from the polymer backbone in others.The influence of the macromolecular structure on the sensing response was studied,especially for the detection of Pb2+,Ni2+,Cd2+and Hg2+. Polymer P6, including thehigher amount of diethylphosphonate groups removed from the polymer chain by ashort alkyl spacer gave the higher sensitivity of detection of lead ions, with a detec-tion limit of 50 pM
KW - Heavy metals
KW - Phosphonate esters
KW - Lead ions
KW - MALDI TOF MS
PY - 2023
DO - https://doi.org/10.1002/pat.6065
SN - 1042-7147
SP - 1
EP - 11
PB - John Wiley & Sons, Ltd
AN - OPUS4-57356
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Seifert, Stephan
A1 - Weidner, Steffen
A1 - Panne, Ulrich
A1 - Kneipp, Janina
T1 - Taxonomic relationship of pollen from MALDI TOF MS data using multivariate statistics
N2 - Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) has been suggested as a promising tool for the investigation of pollen, but the usefulness of this approach for classification and identification of pollen species has to be proven by an application to samples of varying taxonomic relations.
KW - MALDI mass spectrometry
KW - Pollen
KW - Multivariate statistics
PY - 2015
DO - https://doi.org/10.1002/rcm.7207
SN - 0951-4198
SN - 1097-0231
VL - 29
SP - 1145
EP - 1154
PB - Wiley
CY - Chichester
AN - OPUS4-35296
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Thünemann, Andreas
A1 - Knappe, Patrick
A1 - Bienert, Ralf
A1 - Weidner, Steffen
T1 - Online coupling of field-flow fractionation with SAXS and DLS for polymer analysis
N2 - We report on a hyphenated polymer analysis method consisting of asymmetrical flow field-flow fractionation (A4F) coupled online with small-angle X-ray scattering (SAXS) and dynamic light scattering (DLS). A mixture of six poly(styrene sulfonate)s with molar masses in the range of 6.5 × 103 to 1.0 × 106 g mol-1 was used as a model system for polyelectrolytes in aqueous solutions with a broad molar mass distribution. A complete polymer separation and analysis was performed in 60 min. Detailed information for all polymer fractions are available on i) the radii of gyration, which were determined from the SAXS data interpretation in terms of the Debye model (Gaussian chains), and ii) the diffusion coefficients (from DLS). We recommend using the A4F-SAXS-DLS coupling as a possible new reference method for the detailed analysis of complex polymer mixtures. Advantages of the use of SAXS are seen in comparison to static light scattering for polymers with radii of gyration smaller then 15 nm, for which only SAXS produces precise analytical results on the size of the polymers in solution.
PY - 2009
DO - https://doi.org/10.1039/b9ay00107g
SN - 1759-9660
SN - 1759-9679
VL - 1
SP - 177
EP - 182
PB - RSC Publ.
CY - Cambridge
AN - OPUS4-20567
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Meyer, A.
A1 - Kricheldorf, H. R.
T1 - Alcohol-initiated and Tin(II) 2-ethylhexanoate-catalyzed polymerization of L-lactide in bulk – About separate crystallization of cyclic and linear Poly (L-lactide)s
N2 - Alcohol-initiated ROPs of L-Lactide were performed at 140 ◦C in bulk with variation of the initiator/catalyst ratio and time. Lower ratios favor the formation of cycles which upon annealing display a change of the MALDI mass peak distribution towards a new maximum with a “saw-tooth pattern” of the mass peaks representing the cycles.
Such a pattern was not observed for the mass peak of the linear chains. The coexistence of these patterns indicate that linear and cyclic poly (L-lactide)s (PLA) crystallize in separate crystals, and that the crystallites of the cycles are made up by extended rings. High Tm and ΔHm values confirm that these extended-ring crystallites represent a thermodynamically optimized form of PLA. Experiments with preformed cyclic and linear PLAs support this interpretation.
KW - Polylactide
KW - MALDI-TOF MS
KW - Crystalinity
KW - Polymerization
PY - 2023
DO - https://doi.org/10.1016/j.polymer.2023.126355
VL - 285
IS - 126355
SP - 1
EP - 9
PB - Elsevier Ltd.
AN - OPUS4-58355
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H.R.
A1 - Yashiro, T.
A1 - Weidner, Steffen
T1 - Isomerization-free polycondensations of maleic anhydride with alpha,omega-alkanediols
KW - Polymerisation
KW - Polykondensation
KW - MALDI Massenspektrometrie
PY - 2009
DO - https://doi.org/10.1021/ma9009356
SN - 0024-9297
SN - 1520-5835
VL - 42
IS - 17
SP - 6433
EP - 6439
PB - American Chemical Society
CY - Washington, DC
AN - OPUS4-20930
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H.R.
A1 - Weidner, Steffen
T1 - High Tg copolyesters of lactide, isosorbide and isophthalic acid
N2 - Using SnCl2, ZnCl2, Zn-lactate or Zr-acetylacetonate as catalysts ʟ-lactide was oligomerized in bulk with isosorbide as initiator. The ratio isosorbide/lactide was varied from 8/2 to 2/8. The resulting oligomers were in situ polycondensed with isophthaloyl chloride in various aromatic solvents. In chlorobenzene homogeneous reaction mixtures were obtained, whereas molten copolyesters precipitated from toluene and xylene. The obtained average molecular weights indicated high polydispersities. According to MALDI-TOF MS the low molar mass reaction products (<4 kDa) almost exclusively consisted of cyclics with a composition depending on the feed ratio. The glass-transition temperatures (Tg) varied between the values of poly(ʟ-lactide (64 °C) and poly(isosorbide isophthalate) (180 °C). Four polyesters prepared from 5-tert-butyl isophthalic acid displayed higher Tg values. Differential thermoanalysis evidenced that the thermostability decreases with higher fractions of lactide, but processing from the melt seems to be feasible up to temperatures of 260 °C without risking degradation.
KW - Lactide
KW - Isosorbide
KW - Ring-opening polymerization
KW - Polycondensation
KW - Cyclization
PY - 2013
DO - https://doi.org/10.1016/j.eurpolymj.2013.05.007
SN - 0014-3057
SN - 1873-1945
VL - 49
IS - 8
SP - 2293
EP - 2302
PB - Elsevier
CY - Oxford
AN - OPUS4-29014
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Falkenhagen, Jana
A1 - Dalgic, Mete-Sungur
A1 - Weidner, Steffen
T1 - Quantitative MALDI-TOF Mass Spectrometry of Star-Shaped Polylactides Based on Chromatographic Hyphenation
N2 - The end groups of three- and four-arm star-shaped polylactides (PLA) with trimethylolpropane and pentaerythritol core structures were functionalized with acetic acid. Reaction products with different degrees of functionalization were analyzed by matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. Additional gradient elution liquid adsorption chromatography (GELAC) measurements were performed to determine the degree of functionalization. This technique enabled clear separation and sufficient quantification of the formed species. These chromatographic data could be used inversely to quantify mass spectrometric results, which are usually biased by the unknown ionization probabilities of different polymer end group structures. Our results showed that, in this particular case, the peak intensity in the MALDITOF mass spectra can be used to semiquantitatively determine the degree of functionalization in incompletely functionalized multiarm PLA.
KW - Polylactides
KW - MALDI-TOF-MS
KW - Gradient elution liquid adsorption chromatography
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625292
DO - https://doi.org/10.1021/jasms.4c00491
SN - 1879-1123
SP - 1
EP - 9
PB - American Chemical Society (ACS)
AN - OPUS4-62529
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Meyer, Andreas
A1 - Falkenhagen, Jana
A1 - Kricheldorf, Hans R.
T1 - Cyclic polyglycolide by means of metal acetylacetonates
N2 - Glycolide was polymerized in bulk at 160 °C using various metal acetylacetonates as catalysts. Zirconium acetylacetonate was particularly efficient, enabling rapid polymerization even at 130 °C. The formation of cyclic poly(glycolic acid) (PGA), most likely via a ring-expansion polymerization (REP) mechanism, was proven by matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. Depending on the polymerization conditions, the formation of even-numbered cycles was favored to varying degrees. Number-average molecular weights (Mn) in the range of 2000–3500 g mol−1 were achieved with dispersities below 2.0. Wide-angle X-ray scattering (WAXS) powder patterns showed that the crystal lattice was the same as that of known linear PGAs, regardless of the Mn values. These patterns enabled a comparison of crystallinities with values derived from DSC measurements.
KW - MALDI-TOF MS
KW - Polyglycolide
KW - Crystallization
KW - Small-angle X-ray scattering
KW - Cyclization
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-653731
DO - https://doi.org/10.1039/d5ra07961f
SN - 2046-2069
VL - 16
IS - 2
SP - 1757
EP - 1764
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-65373
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
T1 - The role of transesterifications in reversible polycondensations and a reinvestigation of the Jacobson-Beckmann-Stockmayer experiments
N2 - The polycondensations of adipic acid and 1,10-decanediol catalyzed by toluene sulfonic acid (TSA) were reinvestigated using MALDI TOF mass spectrometry and NMR spectroscopy. Unexpected reactions of TSA were detected along with incomplete conversion of the monomers. Furthermore, transesterification reactions of end-capped poly(1,10-decanediol adipate) and end-capped poly(ε-caprolactone) catalyzed by TSA were studied. Despite the quite different (ionic) reaction mechanisms, it was found that for polycondensations performed in bulk intermolecular transesterification is more efficient than the intramolecular “back-biting”; this scenario was not considered in the Jacobson–Stockmayer theory of reversible polycondensations.
These results also confirm that the Jacobson–Stockmayer explanation of reversible polycondensations solely on the basis of ring chain equilibration is not only devoid of any experimental evidence, but also in contradiction to the results elaborated in this work.
KW - Polylactide
KW - MALDI-TOF MS
KW - Polycondensation
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543402
DO - https://doi.org/10.1039/d1py01679b
SN - 1759-9962
SP - 1
EP - 9
PB - RSC Publ.
CY - Cambridge
AN - OPUS4-54340
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
A1 - Krüger, Ralph-Peter
A1 - Just, Ulrich
T1 - Principle of Two-Dimensional Characterization of Copolymers
N2 - Two-dimensional polymer characterization is used for a simultaneous analysis of molar masses and chemical heterogeneities (e.g., end groups, copolymer composition, etc.). This principle is based on coupling of two different chromatographic modes. Liquid adsorption chromatography at critical conditions (LACCC) is applied for a separation according to the chemical heterogeneity, whereas in the second-dimension fractions are analyzed with regard to their molar mass distribution by means of size exclusion chromatography (SEC). Because appropriate standards for a calibration of the SEC are seldom available, matrix-assisted laser desorption/ionization-time-of-flight mass spectrometry (MALDI-TOF MS) was used to substitute the SEC. The LACCC-MALDI MS coupling enables acquiring additional structural information on copolymer composition, which can considerably enhance the performance of this coupled method.
KW - MALDI-TOF MS
KW - Chromatographie
KW - Kopplung
PY - 2007
DO - https://doi.org/10.1021/ac062145f
SN - 0003-2700
SN - 1520-6882
VL - 79
IS - 13
SP - 4814
EP - 4819
PB - American Chemical Society
CY - Washington, DC
AN - OPUS4-17722
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
T1 - Reversible Polycondensations outside the Jacobson-Stockmayer Theory and a New Concept of Reversible Polycondensations
N2 - L-Lactide was polymerized with tin(II)acetate, tin(II)2-ethyl hexanoate, diphenyltin dichloride and dibutyltin bis(pentafluorophenoxide) at 130 °C in bulk. When an alcohol was added as initiator, linear chains free of cycles were formed having a degree of polymerization (DP) according to the lactide/initiator (LA/In) ratio.
Analogous polymerizations in the absence of an initiator yielded high molar mass cyclic polylactides.
Quite similar results were obtained when ε-caprolactone was polymerized with or without initiator.
Several transesterification experiments were conducted at 130 °C, either with polylactide or poly(ε-caprolactone) indicating that several transesterification mechanisms are operating under conditions that do not include formation of cycles by back-biting. Furthermore, reversible polycondensations (revPOCs) with low or moderate conversions were found that did not involve any kind of cyclization. Therefore, These results demonstrate the existence of revPOCs, which do neither obey the theory of irreversible polycondensation as defined by Flory nor the hypothesis of revPOCs as defined by Jacobson and Stockmayer. A new concept encompassing any kind of revPOCs is formulated in the form of a “polycondensation triangle”.
KW - Polylactide
KW - MALDI-TOF MS
KW - Polycondensation
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-530831
DO - https://doi.org/10.1039/d1py00704a
VL - 12
IS - 35
SP - 5003
EP - 5016
PB - Royal Society for Chemistry
AN - OPUS4-53083
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Meyer, A.
A1 - Falkenhagen, Jana
A1 - Kricheldorf, H. R.
T1 - Polycondensations and Cyclization of Poly(L-lactide) Ethyl Esters in the Solid State
N2 - The usefulness of seven different Tin catalysts, Bismuth subsalicylate and Titan tetra(ethoxide) for the polycondensation of ethyl L-lactate (ELA) was examined at 150 °C/6 d. Dibutyltin bis(phenoxides) proved to be particularly effective. Despite the low reactivity of ELA, weight average molecular masses (Mw) up to 12 500 were found along with partial crystallization. Furthermore, polylactides (PLAs) of similar molecular masses were prepared via ELA-initiated ROPs of L-lactide by means of the four most effective polycondensation catalysts. The crystalline linear PLAs were annealed at 140 or 160 °C in the presence of these catalysts. The consequences of the transesterification reactions in the solid PLAs were studied by means of matrix-assisted laser desorption/ionization (MALDI TOF) mass spectrometry, gel permeation chromatography (GPC) and small-angle X-ray scattering (SAXS). The results indicate that polycondensation and formation of cycles proceed in the solid state via formation of loops on the surface of the crystallites. In summary, five different transesterification reactions are required to explain all results.
KW - Polylactide
KW - MALDI-TOF MS
KW - Crystalinity
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-592934
DO - https://doi.org/10.1039/d3py01232h
SN - 1759-9962
VL - 15
IS - 2
SP - 71
EP - 82
PB - RSC Publ.
CY - Cambridge
AN - OPUS4-59293
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Scholz, Philipp
A1 - Wachtendorf, Volker
A1 - Panne, Ulrich
A1 - Weidner, Steffen
ED - Scholz, Philipp
T1 - Degradation of MDI-based polyether and polyester-polyurethanes in various environments - Effects on molecular mass and crosslinking
N2 - Size-exclusion chromatography (SEC) was used to monitor changes of the molecular masses of thermoplastic polyether – and polyester urethane (TPU) exposed to thermal, hydrolytic, and photo-oxidative (UV) Degradation conditions for several days. The thermal treatment was performed at elevated temperatures (100–200 °C) under oxidative (air) as well as non-oxidative (nitrogen) conditions to evaluate the specific influence of oxygen on the degradation. At higher temperatures (≥175 °C) a fast decrease of the molecular masses of both PU accompanied by a high degree of crosslinking was found. At lower temperatures (≤150 °C) the polymers remained widely unaffected by thermal degradation within the investigated degradation interval of up to two weeks. Surprisingly, the influence of oxygen (air) was found to be less distinct. In contrast to that, UV treatment at 25 °C at less than 10% rel. humidity (RH) resulted in a fast crosslinking, whereas the molecular masses of both PU decreased slower than for thermal treatments. The depth of penetration of the UV radiation was estimated using 3D printed PU samples with different thicknesses. Hydrolysis based degradation effects were less significant. Only slight molecular mass changes were detected at temperatures ≤80 °C within a time span of 14 days, while no crosslinking could be measured. Considering the degradation results at the investigated exposure parameters, it could be shown that esterbased PU in general exhibits a significant higher stability compared to ether-based materials.
KW - Polyurethane
KW - Thermal degradation
KW - UV degradation
KW - Molecular masses
KW - Crosslinking
PY - 2019
UR - https://www.sciencedirect.com/science/article/pii/S0142941819302363
DO - https://doi.org/10.1016/j.polymertesting.2019.04.028
SN - 0142-9418
VL - 77
SP - 105881, 1
EP - 12
PB - Elsevier
CY - Amsterdam
AN - OPUS4-48619
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Lahcini, M.
A1 - Qayouh, H.
A1 - Yashiro, T.
A1 - Weidner, Steffen
A1 - Kricheldorf, H.R.
T1 - Bismuth-triflate-catalyzed polymerizations of epsilon-caprolactone
N2 - εCL was polymerized using the triflates of lanthanum, samarium, magnesium, aluminum, scandium, and bismuth as catalysts. Bismuth triflate proved to be extraordinarily reactive, and catalyzed polymerizations of εCL even at 20 °C. Adding DTBMP reduced the polymerization rate only slightly. Furthermore, no evidence of a cationic mechanism was found by end‐group analyses. Polymerization at 20 °C either in bulk or in solution only yielded polyesters of low or medium molecular weights. Yet addition of alcohols allowed for a proper control of molecular weight and end‐groups. Additionally, low catalyst concentrations and low temperature resulted in narrow molecular weight distributions and polylactones almost free of cyclic compounds.
KW - Bismuth
KW - Epsilon-caprolactone
KW - Ring-opening polymerization
KW - Telechelic polyesters
PY - 2011
DO - https://doi.org/10.1002/macp.201000517
SN - 1022-1352
SN - 1521-3935
VL - 212
IS - 6
SP - 583
EP - 591
PB - Wiley-VCH Verl.
CY - Weinheim
AN - OPUS4-23514
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Wettmarshausen, Sascha
A1 - Friedrich, Jörg Florian
A1 - Meyer-Plath, Asmus
A1 - Kalinka, Gerhard
A1 - Hidde, Gundula
A1 - Weidner, Steffen
T1 - Coating of carbon fibers with adhesion-promoting thin poly(acrylic acid) and poly(hydroxyethylmethacrylate) layers using electrospray ionization
N2 - Thin coatings of poly(acrylic acid) (PAA) and poly(hydroxyethylmethacrylate) (PHEMA) were deposited onto carbon fibers by means of the electrospray ionization (ESI) technique in ambient air. These high-molecular weight polymer layers were used as adhesion promoters in carbon fiberepoxy resin composites. Within the ESI process, the carbon fibers were completely enwrapped with polymer in the upper 10 plies of a carbon fiber roving. As identified with scanning electron microscopy also shadowed fibers in a bundle as well as backsides of fiber rovings were pinhole-free coated with polymers (electrophoretic effect'). Under the conditions used, the layers have a granular structure. Residual solvent was absent in the deposit. PAA and PHEMA films did not show any changes in composition and structure in comparison with the original polymers as analyzed by X-ray photo-electron spectroscopy and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. Single-fiber pullout tests of coated fibers embedded in epoxy resin showed significantly increased interfacial shear strength. It is assumed that chemical bonds between carbon fiber poly(acrylic acid) and epoxy resin contribute significantly to the improved interactions.
KW - Adhesion promotion
KW - Thin polymer layers
KW - Electrospray ionization (ESI)
KW - Carbon fiberepoxy resin laminates
KW - Layer topography
PY - 2015
DO - https://doi.org/10.1080/01694243.2015.1040980
SN - 0169-4243
SN - 1568-5616
VL - 29
IS - 15
SP - 1628
EP - 1650
PB - VNU Science Press
CY - Utrecht
AN - OPUS4-34564
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Chatti, S.
A1 - Weidner, Steffen
A1 - Fildier, A.
A1 - Kricheldorf, H.R.
T1 - Copolyesters of isosorbide, succinic acid, and isophthalic acid: biodegradable, high Tg engineering plastics
N2 - Isosorbide, succinyl chloride and isophthaloyl chloride are polycondensed under various reaction conditions. The heating in bulk with or without catalysts as well in an aromatic solvent without catalyst, and polycondensation with the addition of pyridine only yield low molar mass copolyesters. However, heating in chlorobenzene with addition of SnCl2 or ZnCl2 produces satisfactory molar masses. The number average molecular weights (Mn) of most copolyesters fall into the range of 7000–15,000 Da with polydispersities (PD) in the range of 3–9. The MALDI-TOF mass spectra almost exclusively displayed peaks of cyclics indicating that the chain growth was mainly limited by cyclization and not by side reactions, stoichiometric imbalance or incomplete conversion. The glass-transition temperatures increased with the content of isophthalic acid from 75 to 180 °C and the thermo-stabilities also followed this trend.
KW - Biodegradable
KW - Cyclization
KW - Cyclopolymerization
KW - Isophthalic acid
KW - Isosorbide
KW - Polycondensation
KW - Polyesters
KW - Renewable resources
KW - Succinic acid
PY - 2013
DO - https://doi.org/10.1002/pola.26635
SN - 0360-6376
SN - 0887-624X
VL - 51
IS - 11
SP - 2464
EP - 2471
PB - Wiley
CY - Hoboken, NJ
AN - OPUS4-28577
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gille, M.
A1 - Viertel, A.
A1 - Weidner, Steffen
A1 - Hecht, S.
T1 - Modular synthesis of monomers for on-surface polymerization to graphene architectures
N2 - We developed a modular synthesis of halogenated polycyclic aromatic monomers for on-surface polymerization to generate graphene wires, ribbons, and networks.
KW - Graphene monomers
KW - Graphene nanoribbons
KW - Functionalized graphene nanoribbons
KW - Graphene wires
KW - Hexabenzocoronene
KW - On-surface polymerization
PY - 2013
DO - https://doi.org/10.1055/s-0032-1317959
SN - 0936-5214
SN - 1437-2096
VL - 24
IS - 2
SP - 0259
EP - 0263
PB - Thieme
CY - Stuttgart
AN - OPUS4-27621
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kricheldorf, H. R.
A1 - Weidner, Steffen
T1 - About the crystallization of cyclic and linear poly(L-lactide)s in alcohol-initiated and Sn(II)2-ethylhexanoate- catalyzed ROPs of L-lactide conducted in solution
N2 - 1-Hydroxymethylnaphtalene (HMN) or 11-bromoundecanol (BUND) were used as initiators and Sn(II) 2-ethylhexanoate (SnOct2) as catalyst for ROPs of L-Lactide (LA) at 115 °C in bulk or in 4 M and 2M solutions in toluene. The LA/In ratio, the LA/Cat ratio and the time were varied. The matrix-assisted laser desorption/ionization time-of-flight (MALDI TOF) mass spectra exclusively displayed peaks of linear chains, when the ROPs were conducted in bulk. But in contrast to reports in the literature, mixtures of linear and cyclic poly(L-lactide) (PLA), were obtained, when the ROPs were performed in solution. The intensity distribution of the mass peaks of cyclic PLAs displayed a “saw-tooth pattern” after annealing in contrast to the mass peak distribution of the liner chains. This new phenomenon indicated that cyclic PLAs and linear PLAs crystallized in separate crystals from the same reaction mixture. This conclusion was confirmed by fractionated crystallization from 2 M solution, which confirmed that the cyclic PLAs nucleate and crystallize faster than the linear chains.
KW - Polylactide
KW - MALDI-TOF MS
KW - Ring opening polymerization
KW - Crystallization
PY - 2023
DO - https://doi.org/10.1016/j.polymer.2023.125946
SN - 0032-3861
VL - 276
SP - 1
EP - 11
PB - Elsevier Ltd.
AN - OPUS4-57308
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Kricheldorf, H. R.
T1 - Spirocyclic bisphenoxides of Ge, Zr, and Sn as catalysts for ring-expansion polymerizations of L- and meso-lactide
N2 - Spirocyclic phenoxides of germanium, zirconium, and tin were prepared from 2,20-dihydroxybiphenyl and 2,20-dihydroxy-1,10-binaphthyl. Ring-expansion polymerizations of L-lactide are mainly studied at 160 or 180 °C. The reactivity of the catalysts increases in the order: Zr < Ge < Sn. Regardless of catalyst, the weight-average molecular weights (Mw) never exceed 50,000 g mol−1. The resulting poly(L-lactide)s are optically pure and have a cyclic architecture. Decreasing temperature and time favor Formation of even-numbered cycles, and at 102 ° cyclics, almost free of odd-numbered rings are obtained. Analogous polymerizations of meso-lactide give similar results >120 °C, but different results at 100 or 80 °C. Surprisingly, bell-shaped narrow molecular weight distributions are obtained <140 °C, resembling the pattern of living polymerizations found for alcohol-initiated polymerizations. An unusual transesterification mechanism yielding narrow distributions of odd-numbered cycles is discovered too.
KW - Cyclization
KW - Polylactides
KW - MALDI-TOF MS
KW - Ring-opening polymerization
KW - Spirocyclic
PY - 2018
DO - https://doi.org/10.1002/pola.29259
SN - 0887-624X
SN - 1099-0518
VL - 56
IS - 24
SP - 2730
EP - 2738
PB - Wiley Periodicals
AN - OPUS4-46498
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Scholz, Philipp
A1 - Ulbricht, Alexander
A1 - Joshi, Y.
A1 - Gollwitzer, Christian
A1 - Weidner, Steffen
T1 - Microstructure of polymer-imprinted metal–organic frameworks determined by absorption edge tomography
N2 - Mechanochemically synthesized metal–organic Framework material HKUST-1 in combination with acrylonitrile butadiene styrene polymer was used to form a polymer metal–organic framework composite material by a simple extruder.
This composite filament was used for 3D printing. Xray diffraction measurements were used to prove the homogeneous distribution of the metal–organic framework in the polymer on a centimeter scale, whereas X-ray Absorption Edge Tomography using a synchrotron radiation source was able to evaluate the 3D distribution of the metal–organic framework material both in the filament and the resultant printed sample with a resolution of a few lm. Our very first data indicate that, apart from a few clusters having significantly higher Cu concentration, HKUST-1 is distributed homogeneously down to the 100 lm length scale in both polymer bulk materials in the form of clusters with a size of a few lm. Absorption Edge Tomography in combination with data fusion also allows for the calculation of the metal–organic framework amount located on the external polymer surface.
KW - MOF
KW - Polymer
KW - AET
PY - 2019
DO - https://doi.org/10.3139/146.111817
SN - 1862-5282
SP - 1
EP - 10
PB - Carl Hanser Verlag
AN - OPUS4-49483
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Billing, Mark
A1 - Gräfe, Christine
A1 - Saal, Adrian
A1 - Biehl, Philip
A1 - Clement, Joachim
A1 - Dutz, silvio
A1 - Weidner, Steffen
A1 - Schacher, Felix
T1 - Zwitterionic Iron Oxide (γ-Fe2O3) Nanoparticles Based on P(2VP-grad-AA) Copolymers
N2 - This study presents the synthesis and characterization of zwitterionic core–shell hybrid nanoparticles consisting of a core of iron oxide multicore nanoparticles (MCNPs, γ-Fe2O3) and a shell of sultonated poly(2-vinylpyridine-grad-acrylic acid) copolymers. The gradient copolymers are prepared by reversible addition fragmentation chain transfer polymerization of 2-vinylpyridine (2VP), followed by the addition of tert-butyl acrylate and subsequent hydrolysis. Grafting of P(2VP-grad-AA) onto MCNP results in P(2VP-grad-AA)@MCNP, followed by quaternization using 1,3-propanesultone-leading to P(2VPS-grad-AA)@MCNP with a zwitterionic shell. The resulting particles are characterized by transmission electron microscopy, dynamic light scattering, and thermogravimetric analysis measurements, showing particle diameters of ≈70–90 nm and an overall content of the copolymer shell of ≈10%. Turbidity measurements indicate increased stability toward secondary aggregation after coating if compared to the pristine MCNP and additional cytotoxicity tests do not reveal any significant influence on cell viability.
KW - Blockcopolymer
KW - Controlled radical polymerization
KW - Hybrid nanoparticles
KW - Iron oxide nanoparticles
KW - Sulfobetaines
PY - 2017
DO - https://doi.org/10.1002/marc.201600637
SN - 1022-1336
SN - 1521-3927
VL - 38
IS - 4
SP - 1600637-1
EP - 1600637-8
PB - Wiley-VCH
AN - OPUS4-39339
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Mechichi, R.
A1 - Chabbah, T.
A1 - Chatti, S.
A1 - Jlalia, I.
A1 - Sanglar, Corinne
A1 - Casablanca, H.
A1 - Vulliet, E.
A1 - Marestin, C.
A1 - Mercier, R.
A1 - Weidner, Steffen
A1 - Errachid, A.
A1 - Hammani, M.
A1 - Jaffrezic-Renault, N.
A1 - Abderrazak, H.
T1 - Semi‑interpenetrating Network‑Coated Silica Gel Based on Green Resources for the Efcient Adsorption of Aromatic Pollutants from Waters
N2 - In the framework of the development of green analytical chemistry, a silica gel (SG) coated with a semi-penetrating network based on the partially biosourced poly(ethersulfone) is studied for a greener extraction process of aromatic organic pollutants. An optimized composition of the semi-penetrating network (80% of the linear polymer (LP): isosorbide-based poly(ethersulfone) and 20% cross-linking agent (XP) type bismaleimide) leads to a total adsorption of the selected aromatic pollutants, whatever their hydrophilicity. Adsorption characteristic, kinetics and isotherms of the SG-semi-INP LP80/XP20 for p-hydroxybenzoic acid and for toluic acid were studied. Langmuir model led to a better ftting of the adsorption isotherms; the adsorption of toluic acid is easier than that of p-hydroxybenzoic acid. 1/n values of benzoic acid was lower for SGsemi-INP LP80/XP20 compared to biochar and to cross-linked methacrylate resin, showing a higher adsorption efciency.
KW - Isosorbide
KW - Semi-interpenetrating networks
KW - Silica gel modification
KW - Aromatic pollutants
KW - Adsorption
PY - 2022
DO - https://doi.org/10.1007/s42250-022-00463
SN - 2522-5758
SP - 1
EP - 18
PB - Springer
AN - OPUS4-55720
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - You, Zengchao
A1 - Nirmalananthan-Budau, Nithiya
A1 - Resch-Genger, Ute
A1 - Panne, Ulrich
A1 - Weidner, Steffen
T1 - Separation of polystyrene nanoparticles bearing different carboxyl group densities and functional groups quantification with capillary electrophoresis and asymmetrical flow field flow fractionation
N2 - Two sets of polystyrene nanoparticles (PSNPs) with comparable core sizes but different carboxyl group densities were made and separated using asymmetric flow field flow fractionation (AF4), capillary electrophoresis (CE), and the off-line hyphenation of both methods. Our results revealed the significant potential of two-dimensional off-line AF4-CE hyphenation to improve the separation and demonstrated for the first time, the applicability of CE to determine the functional group density of nanoparticles (NPs). Compared to the result acquired with conductometric titration, the result obtained with synthesized 100 nm sized PSNPs revealed only a slight deviation of 1.7%. Commercial 100 nm sized PSNPs yielded a deviation of 4.6 %. For 60 nm sized PSNPs, a larger deviation of 10.6 % between both methods was observed, which is attributed to the lower separation resolution.
KW - Nanoparticle
KW - A4F
KW - Capillary electrophoresis
KW - Carboxyl group
PY - 2020
DO - https://doi.org/10.1016/j.chroma.2020.461392
VL - 1626
SP - 461392
PB - Elsevier B.V.
AN - OPUS4-51080
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Kricheldorf, H.
T1 - Transesterification in alcohol-initiated ROPs of l- and meso-lactide catalyzed by Sn(II) and Sn(IV) compounds at low temperatures
N2 - The purpose of this study is to shed more light on the transesterification processes in alcohol-initiated and tin(II) 2-ethylhexanoate (SnOct2)-catalyzed polymerizations of lactides at low or moderate temperatures. Ethanol-initiated polymerizations are conducted in concentrated solutions at 80 °C and a strong dependence of even/odd equilibration on the alcohol/Sn ratio. Around or above 120 °C cyclization of poly(l-lactide) via “backbiting” occurs as a third mechanism. However, poly(m-lactide) shows a higher cyclization tendency and yields cyclics even at 100 °C. Combinations of ethanol and certain cyclic dibutyltin(IV) catalysts also yield cyclic oligomers of l-lactide at 80 °C. Reaction conditions allowing for a total suppression of all transesterification reactions are not found, but even-numbered poly(m-lactide)s with a purity >95% are obtained at 70 or 60 °C.
KW - Cyclization
KW - MALDI-TOF MS
KW - Polyester
KW - Polylactide
KW - Transesterification
PY - 2018
DO - https://doi.org/10.1002/macp.201800445
SN - 1022-1352
SN - 1521-3935
VL - 219
IS - 24
SP - 1800445, 1
EP - 10
PB - Wiley-VCH
CY - Weinheim
AN - OPUS4-46705
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Garaleh, M.
A1 - Kricheldorf, H.R.
A1 - Weidner, Steffen
A1 - Yashiro, T.
T1 - Hafnium chloride catalyzed polycondensation of Alpha, Omega-alkanediol with dicarboxylic acids or succinic anhydride
KW - Polyester
KW - Polycondensation
KW - Hafnium
KW - Cyclization
PY - 2010
DO - https://doi.org/10.1080/10601320903539199
SN - 1060-1325
SN - 1520-5738
VL - 47
IS - 4
SP - 303
EP - 308
PB - Taylor & Francis
CY - Philadelphia, PA
AN - OPUS4-22953
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - You, Zengchao
A1 - Jakubowski, Norbert
A1 - Panne, Ulrich
A1 - Weidner, Steffen
T1 - Separation of polystyrene nanoparticles with different coatings using two-dimensional off-line coupling of asymmetrical flow field flow fractionation and capillary electrophoresis
N2 - The successful off-line coupling of asymmetrical flow field flow fractionation (AF4) and capillary electrophoresis (CE) for separation of nanoparticles (NPs) with different surface coatings was shown. We could successfully demonstrate that, in a certain NP size range, hyphenation of both techniques significantly improved the separation of differently coated NPs. Three mixtures of polystyrene nanoparticles (PS-NPs) with comparable core sizes but different coatings (no coating/carboxyl-coated) were studied. Separation in either method resulted in non-baseline resolved or non-separated peaks. In contrast, two-dimensional off-line coupling of AF4 and CE resulted in clearly separated regions in their 2 D plots in case of 20 and 50 nm particle mixtures, whereas the 100 nm NP mixture could not be separated at all. Various factors affecting the separation like hydrodynamic diameter or SDS concentration were discussed.
KW - Capillary electrophoresis (CE)
KW - Nanoparticles with same nominal diameter
KW - Surface coating
KW - Two-dimensional off-line coupling
KW - Asymmetrical flow field flow fractionation (AF4)
PY - 2019
DO - https://doi.org/10.1016/j.chroma.2019.01.056
VL - 1593
SP - 119
EP - 126
PB - Elsevier
AN - OPUS4-47363
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Knappe, Patrick
A1 - Panne, Ulrich
T1 - MALDI-TOF imaging mass spectrometry of artifacts in 'dried droplet' polymer samples
N2 - Matrix-assisted laser desorption/ionization-timeof-flight (MALDI-TOF) imaging of polystyrenes with various molecular masses was applied to study spatial molecular mass distribution of polymers in sample spots prepared by the 'dried droplet' method. When different solvents and target surfaces were examined, a segregation of single homologous polymers was observed depending upon the evaporation rate of the solvent. For the observed Patterns left by the evaporating droplet, a hypothesis is offered taking into account different hydrodynamic interactions and diffusion.
The results illustrate that spot preparation using the conventionally 'dried droplet' method is prone to artifacts and should be avoided for reliable and reproducible MALDI mass spectrometry experiments with regards to the Determination of molecular masses and mass distributions.
KW - MALDI
KW - Mass spectrometry imaging
KW - Polymer
KW - Droplet
PY - 2011
DO - https://doi.org/10.1007/s00216-011-4773-1
SN - 1618-2642
SN - 1618-2650
VL - 401
IS - 1
SP - 127
EP - 134
PB - Springer
CY - Berlin
AN - OPUS4-24538
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Scholz, Philipp
A1 - Wachtendorf, Volker
A1 - Elert, Anna Maria
A1 - Falkenhagen, Jana
A1 - Becker, Roland
A1 - Hoffmann, Katrin
A1 - Resch-Genger, Ute
A1 - Tschiche, Harald
A1 - Reinsch, Stefan
A1 - Weidner, Steffen
ED - Scholz, Philipp
T1 - Analytical toolset to characterize polyurethanes after exposure to artificial weathering under systematically varied moisture conditions
N2 - Polyether and -ester urethanes (PU) were exposed to artificial weathering at 40 °C and artificial UV radiation in a weathering chamber. In 3 parallel exposures, humidity was varied between dry, humid, and wet conditions. Material alteration was investigated by various analytical techniques like size exclusion chromatography
(SEC), liquid chromatography-infrared spectroscopy (LC-FTIR), thermal-desorption gas chromatography-mass spectrometry (TD-GC-MS), fluorescence mapping and dynamic mechanical analysis (DMA). Our results show that depending on the weathering conditions, different degradation effects can be observed. By means of SEC an initial strong decrease of the molar masses and a broadening of the mass distributions was found. After a material dependent time span this was followed by a plateau where molar mass changes were less significant. A minor moisture-dependent degradation effect was only found for polyester PU. Fluorescence measurements on two materials revealed an increase in the luminescence intensity upon weathering process reaching a saturation level after about 500 h. The changes in the optical properties observed after different exposure conditions and times were very similar. The TD-GC-MS data showed the fate of the stabilizers and antioxidant in the course of weathering. LC-FTIR measurements revealed a change in peak intensities and the ratio of urethane and carbonyl bands.
KW - Polyurethane
KW - Artificial weathering
KW - Moisture
KW - Crosslinking
KW - Degradation
PY - 2019
UR - https://www.sciencedirect.com/science/article/pii/S0142941819303708
DO - https://doi.org/10.1016/j.polymertesting.2019.105996
SN - 0142-9418
VL - 78
SP - 105996, 1
EP - 9
PB - Elsevier
CY - Amsterdam
AN - OPUS4-48625
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Baumann, Maria
A1 - Falkenhagen, Jana
A1 - Weidner, Steffen
A1 - Wold, C.
A1 - Uliyanchenko, E.
T1 - Characterization of copolymers of polycarbonate and polydimethylsiloxane by 2D chromatographic separation, MALDI-TOF mass spectrometry, and FTIR spectroscopy
N2 - The structure and composition of polycarbonate polydimethylsiloxane copolymer (PC-co-PDMS) was investigated by applying various analytical approaches including chromatographic separation methods, spectrometric, and spectroscopic detection techniques. In particular, size exclusion chromatography (SEC) and liquid adsorption chromatography operating at different conditions (e.g. using gradient solvent systems) were used to achieve separations according to molar mass and functionality distribution. The coupling of both techniques resulted in fingerprint two-dimensional plots, which could be used to easily compare different copolymer batches. Matrix-assisted laser desorption/ionization-time-of-flight (MALDI-TOF) mass spectrometry was applied for structural investigations. The different ionization behavior of both comonomers, however, strongly limited the applicability of this technique. In contrast to that, Fourier-transform Infrared (FTIR) spectroscopy could be used to quantify the amount of PDMS in the copolymer at different points in the chromatogram. The resulting methodology was capable of distinguishing PC-co-PDMS copolymer from PC homopolymer chains present in the material.
KW - FTIR
KW - Liquid chromatography
KW - Mass spectrometry
KW - Gradient elution
KW - Polycarbonate-co-dimethylsiloxane copolymer
PY - 2020
DO - https://doi.org/10.1080/1023666X.2020.1820170
VL - 25
IS - 7
SP - 1
EP - 12
PB - Taylor & Francis
AN - OPUS4-51369
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Falkenhagen, Jana
A1 - Weidner, Steffen
T1 - Detection limits of matrix-assisted laser desorption/ionisation mass spectrometry coupled to chromatography - a new application of solvent-free sample preparation
N2 - The detection limits of matrix-assisted laser desorption/ionisation mass spectrometry (MALDI-MS) by semi-online coupling with chromatography were investigated using various mixtures of polyethylene oxides (PEOs) with different end groups. In contrast to the common dried-droplet sample preparation technique, which results in an inhomogeneous sample-to-matrix ratio within the MALDI spot, the used coupling technique offers a very high reproducibility combined with surpassing sensitivity of a few femtograms over a broad range of sample-to-matrix ratios. These results are in correlation with the results of the recently established solvent-free MALDI-TOFMS method utilising the grinding approach and are also of assistance towards the more theoretical aspect of MALDI that suggests that there is no necessity for an analyte incorporation into a matrix crystal for excellent matrix-assistance.
PY - 2005
DO - https://doi.org/10.1002/rcm.2256
SN - 0951-4198
SN - 1097-0231
VL - 19
IS - 24
SP - 3724
EP - 3730
PB - Wiley
CY - Chichester
AN - OPUS4-11859
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gruendling, T.
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
A1 - Barner-Kowollik, C.
T1 - Mass spectrometry in polymer chemistry: a state-of-the-art up-date
N2 - Two decades after the introduction of matrix assisted laser desorption/ionization (MALDI) and electrospray ionization (ESI), soft ionization mass spectrometry represents a powerful toolset for the structural investigation of synthetic polymers. The present review highlights the current state-of-the-art, covering the latest developments of novel techniques, enabling instrumentation as well as the important applications of soft ionization MS from the beginning of 2008. Special attention is paid to the role that soft ionization MS has played in the mechanistic investigation of radical polymerization processes since 2005.
KW - Polymerization mechanisms
KW - Mass spectrometry
KW - LC-MS coupling
PY - 2010
DO - https://doi.org/10.1039/b9py00347a
SN - 1759-9954
SN - 1759-9962
VL - 1
IS - 5
SP - 599
EP - 617
AN - OPUS4-21906
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
A1 - Much, Helmut
A1 - Krüger, Ralph-Peter
A1 - Friedrich, Jörg Florian
T1 - Determination of chemical and molecular-weight distributions of heterogeneous polymers by means of MALDI-MS coupled with chromatography
T2 - 219th ACS national meeting
CY - San Francisco, CA, USA
DA - 2000-03-26
PY - 2000
SN - 0032-3934
VL - 41
IS - 1
SP - 655
EP - 656
PB - American Chemical Society
CY - Newark, NJ
AN - OPUS4-2169
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Falkenhagen, Jana
A1 - Krüger, Ralph-Peter
A1 - Schulz, Günter
A1 - Weidner, Steffen
T1 - Polymer Characterization by LC / MALDI-MS Coupling
T2 - Vortragstagung "Funktionspolymere für Systemlösungen"
CY - Darmstadt, Germany
DA - 2002-03-18
PY - 2002
AN - OPUS4-1805
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Falkenhagen, Jana
A1 - Friedrich, Jörg Florian
A1 - Schulz, Günter
A1 - Krüger, Ralph-Peter
A1 - Much, Helmut
A1 - Weidner, Steffen
T1 - Liquid Adsorption Chromatography near Critical Conditions of Adsorption coupled with Matrix-assisted Laser Desorption/Ionization Mass Spectrometry
N2 - Chemical heterogeneities and molecular weight distributions of poly(ethylene oxide) (PEO)-co-polymethylene (PM) model oligomers, which are relevant to the synthesis of commonly used tensides, were investigated. For analytical characterization, the well-known principle of liquid adsorption chromatography at 'critical conditions' (LACCC) was modified. Near the critical conditions of adsorption of the PEO unit, e.g., at slight adsorption conditions of PM, the copolymers could be separated according to their PM chain length. The eluates were separated and single fractions of each peak were continuously transferred onto the MALDI target by means of a commercially available device. Simultaneously, the MALDI matrix solution was continuously added with a second pump. This procedure offers the possibility of the formation of homogeneous matrix-polymer textures. By MALDI-MS a complete characterization of the chemical composition (PEO and PM chain length) of each peak could be achieved. The obtained MALDI mass spectra of the eluates at different retention times could be used for the molecular weight calibration of the LAC system. In this way, an additional application of SEC, as in conventional 2D-chromatography, was avoided by using the MALDI method as quasi chromatographic separation
KW - Liquid adsorption chromatography
KW - Matrix-assisted laser desorption
KW - Ionization mass spectrometry
KW - Coupling methods
KW - MALDI
PY - 2000
DO - https://doi.org/10.1080/10236660008034644
SN - 1023-666X
SN - 1563-5341
VL - 5
SP - 549
EP - 562
PB - Gordon and Breach Publ.
CY - Amsterdam
AN - OPUS4-2168
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Weidner, Steffen
T1 - Polymer mass spectrometry at BAM with special emphasis on MALDI and ESI
N2 - Since its introduction mass spectrometric techniques like Matrix-assisted Laser Desorption/ionization (MALDI) and Electrospray Ionization (ESI) have become indispensable for synthetic polymer analyses. Ideally, various polymer properties (monomer structure, masses, mass distribution, end groups) can be determined simultaneously. However, in real life these experiments are always affected by important structural parameters and instrumental limitations.
A short introduction focussing on latest findings with respect to ionisation principles and mechanisms will be given. Recent results from our group will be presented and efforts to avoid common drawbacks of polymer mass spectrometry will be discussed. In this regard, MALDI - Imaging mass spectrometry and the 2D hyphenation of MS with different chromatographic separation techniques were especially useful, since they can provide additional information and reduce the complexity of polymer analyses.
T2 - 21. European Symposium on Polymer Spectroscopy
CY - Linz, Austria
DA - 13.01.2020
KW - Mass spectrometry
KW - MALDI-TOF MS
KW - ESI-TOF MS
KW - Polymer
PY - 2020
AN - OPUS4-50260
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Fandrich, Nick
A1 - Falkenhagen, Jana
A1 - Weidner, Steffen
A1 - Staal, B.
A1 - Thünemann, Andreas
A1 - Laschewsky, A.
T1 - Characterization of new amphiphilic block copolymers of N-vinylpyrrolidone and vinyl acetate, 2 - chromatographic separation and analysis by MALDI-TOF and FT-IR coupling
N2 - PVP-block-PVAc block copolymers were synthesized by controlled radical polymerization applying a RAFT/MADIX system and were investigated by HPLC and by coupling of chromatography to FT-IR spectroscopy and MALDI-TOF MS. Chromatographic methods (LACCC and gradient techniques) were developed that allowed a separation of block copolymers according to their repeating units. The results of the spectroscopic and spectrometric analysis clearly showed transfer between radicals and process solvent. With the use of hyphenated techniques differences between main and side products were detected. In agreement with previously published results, obtained by NMR, SEC, static light scattering and MALDI-TOF MS, our data proved a non-ideal RAFT polymerization.
KW - Amphiphiles
KW - Block copolymers
KW - Liquid chromatography
KW - MALDI
KW - Reversible addition fragmentation chain transfer (RAFT)
KW - Liquid adsorption chromatography at critical conditions
KW - Gradient chromatography
KW - MALDI-TOF mass spectrometry
KW - Hyphenated techniques
KW - Mechanism of polymerization
PY - 2010
DO - https://doi.org/10.1002/macp.201000044
SN - 1022-1352
SN - 1521-3935
VL - 211
IS - 15
SP - 1678
EP - 1688
PB - Wiley-VCH Verl.
CY - Weinheim
AN - OPUS4-22012
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Falkenhagen, Jana
A1 - Weidner, Steffen
T1 - Determination of critical conditions of adsorption for chromatography of polymers
N2 - Liquid chromatography (LC) at critical conditions of adsorption was used to separate various poly(ethylene oxides), poly(propylene oxides) and their copolymers. For the first time, the determination of the critical conditions by means of Ultra Performance Liquid Chromatography (UPLC) coupled to Electrospray Ionization Time-of-flight Mass Spectrometry (ESI-TOF MS) is reported. In contrast to established, mostly laborious routines to find suitable chromatographic separation conditions, this coupling enables a very fast adjustment of parameters. Similar to LC Matrix-assisted Laser Desorption/Ionization Time-of-Flight Mass Spectrometry (LC/MALDI MS) coupling, a two-dimensional analysis of homo- and copolymers regarding its functionality type and molecular weight distribution, as well as copolymer composition, can be performed simultaneously. Furthermore, there is no need for using polymer standards for the determination of critical conditions or Size Exclusion Chromatography calibration.
KW - Polymere
KW - UPLC
KW - ESI-Massenspektrometrie
KW - Kopplung
PY - 2009
DO - https://doi.org/10.1021/ac8019784
SN - 0003-2700
SN - 1520-6882
VL - 81
IS - 1
SP - 282
EP - 287
PB - American Chemical Society
CY - Washington, DC
AN - OPUS4-19619
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weidner, Steffen
A1 - Meyer, A.
A1 - Falkenhagen, Jana
A1 - Kricheldorf, H. R.
T1 - SnOct2-catalyzed and alcohol-initiated ROPs of L-lactide – About the influence of initiators on chemical reactions in the melt and the solid state
N2 - SnOct2 (Sn(II) 2-ethylhexanoate) catalyzed ROPs of L-lactide were performed in bulk with eight different alcohols as initiators. The time was varied between 1 h and 24 h for all initiators. For two initiators the temperature was also lowered to 115 ◦C. Even-numbered chains were predominantly formed in all polymerizations at short times, but the rate of transesterification (e.g. even/odd equilibration) and the molecular weight distribution were found to depend significantly on the nature of the initiator. Observed transesterification reactions also continued in solid poly (L-lactide), and with the most active initiator, almost total equilibration was achieved even at 130 ◦C. This means that all chains including those of the crystallites were involved in transesterification reactions proceeding across the flat surfaces of the crystallites. The more or less equilibrated crystalline polylactides were characterized by DSC and SAXS measurements with regard to their melting temperature (Tm), crystallinity and crystal thickness.
KW - Polylactide
KW - MALDI-TOF MS
KW - Crystallization
KW - Catalysts
KW - SAXS
PY - 2021
DO - https://doi.org/10.1016/j.eurpolymj.2021.110508
VL - 153
SP - 110508
PB - Elsevier Ltd.
AN - OPUS4-52633
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Trimpin, S.
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
A1 - McEwen, C.N.
T1 - Fractionation and Solvent-Free MALDI-MS Analysis of Polymers Using Liquid Adsorption Chromatography at Critical Conditions in Combination with a Multisample On-Target Homogenization/Transfer Sample Preparation Method
N2 - A solvent-free homogenization/transfer matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) method is described for the preparation and precise transfer of up to 100 samples simultaneously on a single MALDI plate. This method is demonstrated using a poly(ethylene oxide) (PEO) mixture consisting of different molecular weights (500-6000) and end groups (PEO, dimethoxy-PEO, monomethoxy monomethacrylate-PEO, and dimethacrylate-PEO) that was fractionated using liquid adsorption chromatography at critical conditions. Off-line fractionation is performed prior to the on-target homogenization/transfer solvent-free sample preparation and MALDI mass analysis. The miniaturization of the solvent-free MALDI approach allowed analysis of less than 2 g per PEO component per fraction corresponding to ~200 pmol for PEO 6000. The amounts of polymer sample used for LC separation and the quality of the MS results are equivalent to the "dry spray" method; however, three times more fractions were collected and analyzed with the newly developed hyphenated approach. The off-line method eliminates optimization of, for example, spray conditions or spreading of organic solvents on the MALDI plate that occurs with droplet deposition methods. The widespread applications of MALDI make this solvent-free, multisample method particularly important as it expands the capabilities for obtaining mass measurements with great efficiencies in areas with increased sample numbers. In addition, the solvent-free method is well suited for automated MALDI analysis as it virtually eliminates the "dead-spot" phenomenon.
PY - 2007
DO - https://doi.org/10.1021/ac070986w
SN - 0003-2700
SN - 1520-6882
VL - 79
IS - 19
SP - 7565
EP - 7570
PB - American Chemical Society
CY - Washington, DC
AN - OPUS4-17737
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Falkenhagen, Jana
A1 - Krüger, Ralph-Peter
A1 - Schulz, Günter
A1 - Weidner, Steffen
T1 - Polymer characterization by LC / MALDI-MS coupling
T2 - Bayreuther Polymer Symposium 2001
CY - Bayreuth, Germany
DA - 2001-09-16
PY - 2001
CY - Bayreuth
AN - OPUS4-2256
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Martins, Ines
A1 - Al-Sabbagh, Dominik
A1 - Bentrup, U.
A1 - Marquardt, Julien
A1 - Schmid, Thomas
A1 - Scoppola, E.
A1 - Kraus, Werner
A1 - Stawski, Tomasz
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Yusenko, Kirill
A1 - Weidner, Steffen
A1 - Emmerling, Franziska
T1 - Formation Mechanism of a Nano-Ring of Bismuth Cations and Mono-Lacunary Keggin-Type Phosphomolybdate
N2 - A new hetero-bimetallic polyoxometalate (POM) nano-ring was synthesized in a one-pot procedure. The structure consists of tetrameric units containing four bismuth-substituted monolacunary Keggin anions including distorted [BiO8] cubes. The nano-ring is formed via self-assembly from metal precursors in aqueous acidic medium. The compound (NH4)16[(BiPMo11O39)4] ⋅ 22 H2O; (P4Bi4Mo44) was characterized by single-crystal X-ray diffraction, extended X-ray absorption fine structure spectroscopy (EXAFS), Raman spectroscopy, matrix-assisted laser desorption/ionisation-time of flight mass spectrometry (MALDI-TOF), and thermogravimetry/differential scanning calorimetry mass spectrometry (TG-DSC-MS). The formation of the nano-ring in solution was studied by time-resolved in situ small- and wide-angle X-ray scattering (SAXS/WAXS) and in situ EXAFS measurements at the Mo−K and the Bi−L3 edge indicating a two-step process consisting of condensation of Mo-anions and formation of Bi−Mo-units followed by a rapid self-assembly to yield the final tetrameric ring structure.
KW - Bismuth
KW - In situ EXAFS
KW - In situ SAXS/WAXS
KW - Lacunary Keggin ion
KW - Polyoxometalates
KW - Self-assembly
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-546823
DO - https://doi.org/10.1002/chem.202200079
SN - 0947-6539
VL - 28
IS - 27
SP - 1
EP - 7
PB - Wiley-VCH
CY - Weinheim
AN - OPUS4-54682
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Weidner, Steffen
A1 - Falkenhagen, Jana
A1 - Friedrich, Jörg Florian
A1 - Krüger, Ralph-Peter
A1 - Schulz, Günter
A1 - Much, Helmut
T1 - Liquid Adsorption Chromatography near Critical Conditions of Adsorption coupled with Matrix-assisted Laser/Ionization Mass Spectrometry
T2 - 47th ASMS Conference on Mass Spectrometry and Allied Topics
CY - Dallas, TX, USA
DA - 1999-06-13
PY - 1999
CY - Dallas, Tex
AN - OPUS4-2165
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -