TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Grundsätzliches zur Frage der "UV-Beständigkeit" bzw. der "Lichtbeständigkeit" polymerer Werkstoffe T2 - 42. Jahrestagung der Gesellschaft für Umweltsimulation, GUS. "Umwelteinflüsse erfassen, simulieren, bewerten" CY - Stutensee, Germany DA - 2013-03-20 PY - 2013 AN - OPUS4-27914 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Krüger, Oliver A1 - Geburtig, Anja T1 - Development of al leaching test to estimate emissions from synthetic sports grounds into soil and ground water under weathering exposure T2 - [Conference] "Service Life Prediction of Polymeric Materials: Vision for the Future" CY - Monterey, CA, USA DA - 2013-03-03 PY - 2013 AN - OPUS4-27915 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - New ways for early detection of polymer ageing N2 - Photo-oxidative ageing of polymers under defined exposure (UV, humidity) was investigated from two points of view: a) the ageing process Starts from the topmost surface and penetrates slowly towards bulk and b) radicals play an important role among ageing. Therefore, X-ray photoelectron (XPS) and electron spin resonance (ESR) spectroscopy were applied to show both, the progressive incorporation of oxygen during in-situ UV irradiation (XPS) and the formation of radicals (ESR) in the polymer. The intensity of ESR Signals served as measure for radical concentration. The Validation of this correlation was checked for polyethylenes (PE) equipped with different concentrations of Hostavin N30 UV stabilizer. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 157 EP - 163 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - Influence of UV weathering and humidity on surface & bulk properties of LDPE N2 - The outdoor weathering of polymers is mainly due to UV radiation, water, Pollution, humidity, temperature etc. To understand the effects of weathering, simulated tests need to be undertaken in lab scale. Such tests must be quite efficient and similar to the effects of natural weathering. This paper mainly focuses on the effects of UV radiation along with humidity on LDPE. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - LDPE KW - UV weathering KW - Humidity PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 211 EP - 218 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Kömmling, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - UV-LEDs - a new tool to determine the spectral response N2 - To determine a polymer’s spectral response of photo degradation, two main methods have been established. The so-called “filter technique” uses polychromatic radiation, which is filtered by a set of various sharp cut-on filters. This procedure provides separated reading points of an activation spectrum of the investigated material. With the "spectrographic technique” a specimen is irradiated with pectrally dispersed radiation, locally quasi monochromatically, and the local property changes.are related to the radiant exposure at the respective wavelengths. A third method, the irradiation of specimens with quasi monochromatic radiation behind interference filters, is rarely used. These methods have advantages and disadvantages and therefore, there are limits for conclusions from these spectral data. Concerning the quasi monochromatic Irradiation of specimens the development of new UV radiation sources looks promising. With the rapid development of inexpensive UV Light-emitting diodes (LEDs), new : sources of nearly monochromatic radiation in the UV ränge are available, even down to about 250 nm. To determine the spectral response, the use of such UV-LEDs in TO-18 ) and TO-39 metal cases combines the advantages of low cost and energy efficiency, stable spectral irradiance, temperature.and humidity control, larger specimen areas, and an easy and stable analysis. Combinations of different UV LEDs are also discussed as replacement for xenon arc ' radiation sources, see patent application EP01528388A1. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - UV resistance KW - Weathering KW - Spectral sensitivity KW - Action spectrum KW - UV-LEDs PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 77 EP - 86 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Barthel, Anne-Kathrin A1 - Meyer-Plath, Asmus A1 - Schwiegelshohn, A. A1 - Rauth, W.. A1 - Voetz, Matthias A1 - Rhiem, St. A1 - Schaeffer, A. T1 - Untersuchungen zur witterungsbedingten Partikelfreisetzung aus CNT-Compositen T2 - Inno.CNT Jahreskongress 2012, Innovationsallianz Carbon Nanotubes CY - Bayreuth, Germany DA - 2012-01-30 PY - 2012 AN - OPUS4-25458 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Purohit, Purv A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian T1 - A detailed dielectric relaxation spectroscopy study of artificial UV weathered low density polyethylene N2 - Artificial weathering of LDPE under dry conditions (<10% of relative humidity) by UV radiation was monitored by dielectric spectroscopy. For an apolar polymer like LDPE, dielectric study yields information about the change in structure and dynamics of the system. The fluctuations of the polar groups which are generated as a result of photooxidation such as carbonyl groups can be monitored as characteristic relaxation processes like the αc or β mode. The dielectric loss characterized by typical dielectric parameters like the activation energy and dielectric strength are strongly dependent upon changes induced by photooxidation in the amorphous and crystalline domains. This paper discusses in detail how the foil reached its mechanical disintegration. It was found that initial stages of weathering induce chain scission and/or crosslinking in the amorphous domains of the polymer and the motional processes in the crystalline regions are not affected. After this induction period, an increase in the degree of crystallization was observed by employing differential calorimetry. The increasing crystallinity is considered as one of the reasons for embrittlement which finally leads to the complete loss of the structural integrity. KW - Artificial weathering KW - UV radiation KW - Dielectric relaxation KW - LDPE PY - 2012 DO - https://doi.org/10.1016/j.tca.2011.12.003 SN - 0040-6031 SN - 1872-762X VL - 530 SP - 73 EP - 78 PB - Elsevier CY - Amsterdam AN - OPUS4-25547 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Analyse witterungsbedingter Eigenschaftsänderungen T2 - Seminar "Bewitterung von Kunststoffen und Lacken" der Technischen Akademie Wuppertal CY - Altdorf, Germany DA - 2007-05-10 PY - 2007 AN - OPUS4-15903 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Spektrale Empfindlichkeit der Photoalterung von Lacken und Kunststoffen T2 - Fachtagung "Bewitterung von Kunststoffen und Lacken in der Automobilindustrie" des Süddeutschen Kunststoff-Zentrums CY - Würzburg, Germany DA - 2007-02-07 PY - 2007 AN - OPUS4-15904 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Notwendigkeit der Erfassung klimatischer Einflüsse auf Transportbehälter aus Kunststoff T2 - CEEES Kongress 2007, "Umweltsimulation in der Produktentwicklung" CY - Nuremberg, Germany DA - 2007-05-22 PY - 2007 AN - OPUS4-15905 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter A1 - Schulz, Ulrich T1 - Artificial weathering including acidic deposition T2 - 3rd European Weathering Symposium CY - Kraków, Poland DA - 2007-09-12 PY - 2007 AN - OPUS4-15907 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Wachtendorf, Volker A1 - Rauth, W. A1 - Klimmasch, T. A1 - Krüger, P. T1 - Screening the weathering stability of automotive coatings by chemiluminescence N2 - Chemiluminescence (CL) is a sensitive method of investigating the thermo-oxidative stability of polymers in the early stages of degradation. Therefore, CL measurements were applied to different automotive coatings to evaluate their degradation behavior during artificial weathering. In this work, CL measurements were carried out for different automotive coatings to follow their degradation behavior during artificial weathering. The CL emission depends on sample-specific parameters like stabilizer, matrix, or hardener; experimental parameters like the oxygen partial pressure; and exposure parameters like the duration of weathering. The potential of CL could be demonstrated by classifying materials into categories of good, medium, and low degradation performance at a much earlier stage of weathering exposure than in combination with the usual visual detection of weathering effects. KW - Accelerated weathering KW - Coating KW - Chemiluminescence KW - Sensitive detection KW - Weathering PY - 2008 DO - https://doi.org/10.1007/s11998-007-9071-7 SN - 1547-0091 SN - 1935-3804 VL - 5 IS - 1 SP - 17 EP - 24 PB - Springer CY - Blue Bell, Pa. AN - OPUS4-16723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Chancen und Grenzen der Verkürzung von Bewitterungstests durch empfindliche Chemilumineszenz-Detektion N2 - Eine Verkürzung der Dauer von Bewitterungsversuchen kann durch eine empfindlichere Detektion der Bewitterungseffekte erreicht werden als sie konventionell benützt wird. Eine solche besonders empfindliche Detektionsmethode stellt die Chemilumineszenz dar. Die Verkürzung durch empfindliche Detektion muss jedoch gleichzeitig der Bedingung genügen, ausreichend gute Rangkorrelation zu Bewitterungseffekten unter Anwendungsbedingungen zu zeigen. In diesem Spannungsfeld sollen die Möglichkeiten der Chemiluminiszenz-Detektion beleuchtet werden. T2 - DFO Qualitätstage 2008 CY - Fürth, Deutschland DA - 2008-10-07 KW - Chemilumineszenz KW - Bewitterung KW - Verkürzung KW - empfindlicher Nachweis PY - 2008 SN - 978-3-89943-072-1 SP - 105 EP - 120 PB - DFO CY - Fürth AN - OPUS4-18328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Accelerated weathering test for plastics and coatings that are exposed to acidic precipitation N2 - Due to the occurrence of acidic precipitation, and due to the fact that polymers and stabilizers may be sensititve to acids, it is important to have a laboratory test that combines weathering exposure with acidic exposure. The loss of stabilization caused by an acid damage of stabilizing system gets evident only over the weathering progress. For solid samples, for wich mostly the surface properties are relevant, the "Acid Dew and Fog Test" (ADF test) was established. For woven or tufted materials, the "Acid Rain Test" (AR test) was developed. The proposed weathering tests aim at plastics as well as at coatings. T2 - 7th International Symposium on Weatherability (7th ISW) CY - Kanagawa, Japan DA - 2008-10-23 KW - Acid rain KW - ADF KW - Acid Dew and Fog test KW - Artificial Weathering test PY - 2009 SN - 1346-0633 VL - 21 IS - 2 SP - 69 EP - 73 PB - Materiaru-Raifu-Gakkai CY - Tokyo AN - OPUS4-18270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Zieghahn, K. T1 - Grundsätzliches zur Lebensdauervorhersage in der Bewitterung T2 - Umwelteinflüsse erfassen, simulieren, bewerten : 34. Jahrestagung der GUS 2005 CY - Pfinztal bei Karlsruhe, Deutschland DA - 2005-03-02 KW - Lebensdauer KW - Bewitterung KW - Polymere PY - 2005 SN - 3-9808382-6-9 SP - 159 EP - 168 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-7141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter A1 - Schulz, Ulrich T1 - Artificial weathering including acidic deposition T2 - 3rd European Weathering Symposium CY - Krakow, Poland DA - 2007-09-12 KW - Spectral sensitivity KW - Weathering KW - UV KW - Action spectra KW - Activation spectra KW - Stabilizer KW - Spektrale Empfindlichkeit KW - Bewitterung KW - Aktivierungsspektrum KW - Wirkungsspektrum KW - Stabilisator PY - 2007 SN - 978-3-9810472-3-3 VL - 8 SP - 487 EP - 500 CY - Pfinztal AN - OPUS4-15923 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Improved Evaluation of Activation Spectra Determined by the Filter Technique T2 - 3rd European Weathering Symposium CY - Krakow, Poland DA - 2007-09-12 KW - Spectral sensitivity KW - Weathering KW - UV KW - Action spectra KW - Activation spectra KW - Stabilizer KW - Spektrale Empfindlichkeit KW - Bewitterung KW - Aktivierungsspektrum KW - Wirkungsspektrum KW - Stabilisator PY - 2007 SN - 978-3-9810472-3-3 VL - 8 SP - 349 EP - 358 CY - Pfinztal AN - OPUS4-15924 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - The Principle of Reciprocity and its Limits T2 - 3rd European Weathering Symposium CY - Krakow, Poland DA - 2007-09-12 KW - Spectral sensitivity KW - Weathering KW - UV KW - Action spectra KW - Activation spectra KW - Stabilizer KW - Spektrale Empfindlichkeit KW - Bewitterung KW - Aktivierungsspektrum KW - Wirkungsspektrum KW - Stabilisator PY - 2007 SN - 978-3-9810472-3-3 VL - 8 SP - 243 EP - 258 CY - Pfinztal AN - OPUS4-15925 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - The influence of humidity and wetness on weathering results T2 - Konferenz ATCAE (Atlas Technical Conference for Accelerated Ageing and Evaluation) CY - Oxford, England DA - 2008-09-15 PY - 2008 AN - OPUS4-18000 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Spectral sensitivity of polymer ageing T2 - 4th International Symposium on Service Life Prediction CY - Key Largo, FL, USA DA - 2006-12-03 PY - 2006 AN - OPUS4-14144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Chemiluminescence detection: principles, chances, and limitations for the shortening of weathering tests T2 - 4th International Symposium on Service Life Prediction CY - Key Largo, FL, USA DA - 2006-12-03 PY - 2006 AN - OPUS4-14145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Brademann-Jock, Kerstin A1 - Wachtendorf, Volker A1 - Rauth, W. A1 - Klimmasch, T. A1 - Krüger, P. T1 - Analysis of weathering effects in automotive coatings by thermoluminescence KW - Automotive coatings KW - Weathering KW - Thermoluminescence PY - 2006 SN - 0048-4225 N1 - Sprachen: Englisch/Italienisch - Languages: English/Italian VL - 82 IS - 17 SP - 5 EP - 11 AN - OPUS4-14296 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Der Einfluss von Feuchte und Nässe bei der Bewitterung T2 - 36. Jahrestagung der GUS 2007 CY - Pfinztal bei Karlsruhe, Deutschland DA - 2007-03-14 KW - Spectral sensitivity KW - Weathering KW - UV KW - Action spectra KW - Activation spectra KW - Stabilizer KW - Spektrale Empfindlichkeit KW - Bewitterung KW - Aktivierungsspektrum KW - Wirkungsspektrum KW - Stabilisator PY - 2007 SN - 978-3-9810472-1-9 VL - 36 SP - 247 EP - 256 CY - Pfinztal AN - OPUS4-14758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Wachtendorf, Volker A1 - Rauth, W. T1 - Kürzer in der Klimakammer - Rasche Beurteilung der Bewitterungsstabilität von 2K-PUR-Autolacken mittels Chemilumineszenz KW - Weathering KW - Chemiluminescence KW - Degradation KW - Coatings PY - 2007 SN - 0014-7699 VL - 113 IS - 9 SP - 46 EP - 49 PB - Vincentz CY - Hannover AN - OPUS4-15786 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Grundsätzliches zur Verfahrensauswahl bei der künstlichen Bestrahlung und Bewitterung T2 - 37. Jahrestagung der Gesellschaft für Umweltsimulation CY - Pfinztal, Germany DA - 2008-03-12 PY - 2008 AN - OPUS4-17337 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Grundsätzliches zur Verfahrensauswahl bei der künstlichen Bestrahlung und Bewitterung KW - Bewitterung KW - Bestrahlung KW - Fluoreszenzlampe KW - Xenonlampe PY - 2008 SN - 978-3-9810472-6-4 SP - 109 EP - 121 AN - OPUS4-17338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter ED - Jonathan W. Martin, ED - Rose A. Ryntz, ED - J. Chin, ED - Ray A. Dickie, T1 - Chemiluminescence detection: Principles, chances and limitations for the shortening of weathering tests T2 - 4th International Symposium on Service Life Prediction CY - Key Largo, FL, USA DA - 2006-12-03 KW - Chemiluminescence KW - Weathering KW - Quantum efficiency KW - Accelerated test KW - Automotive coating KW - PE Chemilumineszenz KW - Bewitterung KW - Quantenausbeute KW - Beschleunigter Test KW - Automobillacke PY - 2008 SN - 978-0-387-84875-4 SP - 309 EP - 326 PB - Springer AN - OPUS4-18245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Schulz, Ulrich T1 - Applying Artificial Endurance Tests for the Performance of Vehicle Coatings T2 - Tagung "International Best Practice in Vehicle Coatings" CY - Brussels, Belgium DA - 2005-02-23 PY - 2005 AN - OPUS4-7350 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Using Chemiluminescence as Sensitive Detector of Early Stages Weathering Effects on Car Coatings to shorten Weathering Tests T2 - 2nd European Weathering Symposium CY - Gothenburg, Sweden DA - 2005-06-15 PY - 2005 AN - OPUS4-10446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Principles and Limitations in the Acceleration of Artificial Weathering Tests T2 - 6th International Paint, Varnish, Ink & Auxiliary Products Industry Congress & Exhibition, 2006 Paint CY - Istanbul, Turkey DA - 2006-05-17 KW - Bewitterung KW - Verkürzung KW - Zeitraffung KW - Weathering KW - Shortening KW - Time-lapse PY - 2006 SN - 994-489125-8 SP - 48 EP - 54 PB - TMMOB CY - Istanbul AN - OPUS4-12391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Principles and limitations in the acceleration of artificial weathering tests T2 - Paint 2006, VI. International Paint, Varnish, Ink & Auxiliary Products Industry Congress & Exhibition, "Smart Coatings and new Technologies" CY - Istanbul, Turkey DA - 2006-05-17 PY - 2006 AN - OPUS4-12403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Appajaiah, Anilkumar A1 - Wachtendorf, Volker A1 - Daum, Werner T1 - Characterization of thermo-oxidative stability of polymer optical fibers using chemiluminescence technique N2 - The thermo-oxidative stability of commercially available polymer optical fibers (POFs) and their components (cores and claddings) was investigated. All the bare POFs (core and cladding only) studied here were based on poly(methyl methacrylate) (PMMA) core. The fibers were exposed to 100 °C/low humidity for about 4200 h. Chemiluminescence (CL) technique was applied to investigate the thermo-oxidative stability and for measuring the transmission loss during exposure a prototype device called multiplexer was used. POFs exhibited variation in thermo-oxidative stability although they possessed identical core material PMMA. This was due to difference in the chemical compositions of claddings. Claddings were more susceptible to the thermo-oxidative degradation compared to cores. The thermo-oxidative degradation of both the cladding and the core was found in POFs as a result of climatic exposure. POFs showed an early drop-off followed by a slow decline of transmission. The early drop-off of transmission was attributed to physical changes like thermal expansion and the slow decline of transmission to chemical changes like oxidative degradation of POFs. A good linear relationship between optical transmission stability and thermo-oxidative stability of POFs was established from these studies. KW - Polymer optical fibers (POFs) KW - Chemiluminescence (CL) KW - Thermo-oxidative stability KW - Aging KW - Optical transmission stability PY - 2006 DO - https://doi.org/10.1016/j.polymdegradstab.2006.05.006 SN - 0141-3910 SN - 1873-2321 VL - 91 IS - 11 SP - 2605 EP - 2613 PB - Applied Science Publ. CY - London AN - OPUS4-13984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Der Einfluss von Temperatur und Feuchte bei der Bewitterung T2 - Seminar Technische Akademie Wuppertal CY - Altdorf, Germany DA - 2009-04-02 PY - 2009 AN - OPUS4-20721 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Analyse witterungsbedingter Eigenschaftsänderungen T2 - Seminar Technische Akademie Wuppertal CY - Altdorf, Germany DA - 2009-04-02 PY - 2009 AN - OPUS4-20722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Ansätze zur Testverkürzung T2 - Seminar Technische Akademie Wuppertal CY - Altdorf, Germany DA - 2009-04-02 PY - 2009 AN - OPUS4-20723 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Saure Niederschläge und ihre Wirkung auf den Photoabbau T2 - Seminar Technische Akademie Wuppertal CY - Altdorf, Germany DA - 2009-04-02 PY - 2009 AN - OPUS4-20724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja ED - Ziegahn, K.-F. T1 - Zusammenhang von molekularen Alterungsvorgängen und beobachtbaren Eigenschaftsänderungen bei der Bewitterung von Polymeren T2 - 39. Jahrestagung der GUS 2010 - Umweltflüsse erfassen, simulieren, bewerten CY - Stutensee, Deutschland DA - 2010-03-17 KW - Bewitterung KW - Alterung KW - Eigenschaftsänderung KW - Korrelation PY - 2010 SN - 978-3-9813136-0-4 SP - 45 EP - 55 PB - DWS Werbeagentur und Verlag GmbH CY - Pfinztal AN - OPUS4-21047 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Zusammenhang von molekularen Alterungsvorgängen und beobachtbaren Eigenschaftsänderungen bei der Bewitterung von Polymeren T2 - 39. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) CY - Stutensee, Germany DA - 2010-03-17 PY - 2010 AN - OPUS4-21013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Alterungsvorgänge durch Bewitterung bei Beschichtungen und deren Untersuchung und Prüfung T2 - 42. SAH-Tagung 2010, "Holzoberflächen in der Fassadengestaltung", Schweizerische Arbeitsgemeinschaft für Holzforschung CY - Weinfelden, Switzerland DA - 2010-10-26 PY - 2010 AN - OPUS4-22587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Damerau, Thomas A1 - Sabelus, Silke A1 - Wachtendorf, Volker A1 - Hennecke, Manfred A1 - Greiner, A. T1 - Photochemische und thermische Stabilität eines Phenylen-Vinylen-Polymeren KW - Photostability KW - Fluorescence KW - Chemiluminescence PY - 1996 SN - 0016-3538 VL - 40 IS - 7 SP - 710 EP - 712 PB - GIT-Verlag CY - Darmstadt AN - OPUS4-23205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Hennecke, Manfred T1 - chemiluminescence studies on the thermooxidative stability of poly(1,4-phenyl phenylene vinylene) T2 - 11th Bratislava IUPAC/FECS International Conference on Polymers CY - Stará Lesná, Slovakia DA - 1996-06-24 PY - 1996 AN - OPUS4-23140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Alterungseffekte bei Polymerwerkstoffen messen N2 - Bei der Auswahl von Werkstoffen spielt deren Alterung oft eine untergeordnete Rolle, stattdessen wird häufig der ungealterte Ausgangszustand optimiert. Materialien altern aber unterschiedlich. Der Effekt der molekularen Alterung spiegelt sich in den Eigenschaften mehr oder weniger stark und in unterschiedlichem zeitlichen Verlauf wider. Da es kein physikalisch-chemisches Modell dafür gibt, sind Alterungseffekte empirisch zu bestimmen. KW - Alterung KW - Polymerwerkstoff KW - Eigenschaftsänderung PY - 2012 DO - https://doi.org/10.1002/nadc.201290356 SN - 1439-9598 SN - 1521-3854 VL - 60 IS - 10 SP - 1018 EP - 1022 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-26666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Berger, Wolfgang A1 - Wachtendorf, Volker A1 - Hally, S. ED - Arm, M. ED - Vandecasteele, C. ED - Heynen, J. ED - Suer, P. ED - Lind, B. T1 - Development of leaching procedures for synthetic turf systems T2 - WASCON 2012 CY - Gothenburg, Sweden DA - 0201-05-30 KW - Waste rubber KW - Artificial turf KW - Leaching behaviour KW - Batch test KW - Column test PY - 2012 SP - 1 EP - 5(?) PB - ISCOWA and SGI AN - OPUS4-26968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Wachtendorf, Volker A1 - Berger, Wolfgang T1 - Umweltverträglichkeit von Kunststoff- und Kunststoffrasenbelägen auf Sportfreianlagen KW - Sportboden KW - Sportbodenbelag KW - Kunststoffbelag KW - Kunststoffrasenbelag KW - Kunstrasen KW - Schadstoff KW - Umweltverträglichkeit KW - Ökotoxizität PY - 2012 SN - 978-3-86884-522-8 IS - 2 SP - 1 EP - 261 PB - Sportverlag Strauß CY - Bonn AN - OPUS4-26997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Goedecke, Thomas A1 - Wachtendorf, Volker T1 - Combined impact of ultraviolet and chemical fluids on high-density polyethylene packaging material N2 - To investigate the ageing behaviour of filled plastic containers outdoors, square cuts of the wall of two high-density polyethylene (HDPE) types were exposed to ultraviolet (UV) radiation at their front side and to specific liquid chemicals (de-ionized water, surfactant or White Spirit) at their back. The UV radiant exposure at the front side was 80 MJ/m². To compare the actions of the different exposures, separate dark backside fluid exposures were performed, in parallel. Besides, UV weathering was carried out until a UV radiant exposure of 325 MJ/m², being roughly comparable to outdoor exposure of one year in Northern Australia. An unpigmented HDPE included in the investigation gave no sufficient protection for the White Spirit. In addition, it showed clear degradation after several of these exposures. In combination with the White Spirit, an increase of carbonyl bonds was measured, presumably assignable to degradation products of the White Spirit. For a pigmented HDPE material, with the implemented combined exposures, no relevant damage was observed, within applied the exposure period. KW - Weathering KW - UV KW - HDPE KW - Packaging PY - 2012 DO - https://doi.org/10.1002/pts.959 SN - 0894-3214 VL - 25 IS - 1 SP - 53 EP - 61 PB - Wiley CY - Chichester, UK AN - OPUS4-25417 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Wachtendorf, Volker A1 - Berger, Wolfgang A1 - Hally, S. T1 - Development of leaching procedures for synthetic turf systems containing scrap tyre granules N2 - Scrap tyres are widely reused in the form of granules as infill materials or component of sub-base layers in construction of sporting grounds such as synthetic turf areas and athletic track surfaces. The recycled rubber may contain organic and inorganic pollutants due to the presence of vulcanisation catalysts, stabilisers and other additives which can be released into soil and groundwater in the case of outdoor sports facilities. In order to evaluate the amount of potentially mobile pollutants, leaching tests can be employed. This study aimed particularly at the investigation of the feasibility of column tests using complete synthetic surface flooring or turf system assemblies. The release of zinc and polycyclic aromatic hydrocarbons (PAH) leached from components of sports surfaces containing recycled rubber granules was considered. Additionally, batch tests on coated and uncoated styrene butadiene rubber (SBR) granules aged by artificial weathering were performed to indicate its possible influence on the leaching behaviour of zinc and PAH. The chosen approach of column tests simulating typical complete synthetic sports surface installations has been proven to be feasible and robust. The time-dependent leaching behaviour and interactions between single components can be evaluated by column tests. Zinc was the most relevant contaminant in the eluates and its leachability was enhanced after accelerated ageing by artificial weathering. Leachable PAH were found in relatively low but well detectable amounts which increase by ageing as well. KW - Waste rubber KW - SBR KW - Artificial turf KW - Leaching KW - behaviour KW - Column test KW - Batch test KW - Weathering PY - 2013 DO - https://doi.org/10.1007/s12649-013-9248-5 SN - 1877-2641 SN - 1877-265X VL - 4 IS - 4 SP - 745 EP - 757 PB - Springer Science + Business Media CY - Dordrecht AN - OPUS4-29454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid on high‐density polyethylene containers as a laboratory test N2 - In a laboratory test, transparent high‐density polyethylene (HDPE) jerrycans have been exposed to both UV radiation and 55 wt‐% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The damages are compared with FTIR spectroscopy in ATR and HT‐gel permeation chromatography(GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. This is caused by the decomposition of nitric acid into nitrous gases by UV radiation, which is also observed at lower concentrations (28 wt‐%). After 6 days of laboratory exposure, this is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. The gradual increase in oxidative damage shows the reproducibility of the test. KW - Molecular mass distribution KW - High-density polyethylene KW - Nitric acid KW - UV radiation PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-550141 DO - https://doi.org/10.1002/pts.2673 SN - 0894-3214 SP - 1 EP - 7 PB - John Wiley & Sons Ltd AN - OPUS4-55014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Messung der Temperatur von bestrahlten Oberflächen-Blechdicke beim BST N2 - Die Grenzen der Oberflächentemperaturen von Proben, die der natürlichen oder einer künstlichen Globalstrahlung ausgesetzt sind, können grob mit sog. Schwarzstandard Thermometern BST oder Weißstandard Thermometern WST ermittelt werden [ 1a) ]. Um einige Mängel der aktuellen Konstruktion zu beseitigen, wird ein neues Konzept dieser Thermometer vorgeschlagen, das sie weniger träge und ihre physikalischen Eigenschaften ähnlicher denen einer 5 mm dicken Polymerplatte macht. Es wird auch gezeigt, dass eine Anforderung an die Reaktionszeit von weniger als 1 min in EN 513 unrealistisch ist. T2 - 45. Jahrestagung der GUS CY - Stutensee DA - 16.03.2016 KW - Oberflächentemperatur KW - Strahlungserwärmung KW - IR-Thermometer PY - 2016 SN - 978-3-9816286-7-8 SP - 125 EP - 134 AN - OPUS4-36916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meyer, S. A1 - Timmel, S. A1 - Gläser, M. A1 - Braun, Ulrike A1 - Wachtendorf, Volker A1 - Hagendorf, C. T1 - Polymer foil additives trigger the formation of snail trails in photovoltaic modules N2 - After several months of operation, many photovoltaic (PV) modules develop a discolouration defect called snail trails which appear as irregular dark traces across the cells. These traces are caused by silver nanoparticles accumulating within the encapsulation foil directly above the grid finger. In this work we systematically investigate combinations of encapsulation and back-sheet foils with respect to their susceptibility for snail trails. We can show that certain additive compositions within the encapsulation and back sheet foils are critical for the formation of the discolouring silver nanoparticles. We suggest a reaction model explaining the formation of snail trails from a chemical point of view. This fundamental understanding allows the rapid testing of foils for their snail trail sensitivity as well as the special design of resistant foils. KW - Snail trails KW - Encapsulation foil KW - Back-sheet foil KW - Additives KW - Silver nanoparticles PY - 2014 DO - https://doi.org/10.1016/j.solmat.2014.06.028 SN - 0927-0248 VL - 130 SP - 64 EP - 70 PB - Elsevier B.V. CY - Amsterdam [u.a.] AN - OPUS4-31249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Goedecke, Thomas A1 - Wachtendorf, Volker ED - Sek, M.A. ED - Rouillard, V. ED - Bigger, S.W. T1 - Outdoor weathering of HDPE containers filled with nitric acid N2 - Jerrycans made from three different types of high-density polyethylene (HDPE) were exposed outdoors, for one Berlin summer season. They were filled with a 55 percent nitric acid solution (HN03), pure water, or air, and half of them were protected from sunlight by an UV absorbing canvas. Thus, the separate effects of UV radiation and nitric acid could be compared to the combined impact. Combined impact was mainly affected by decomposition of nitric acid, resulting in presence of reactive nitrogen oxides, increased oxygen partial pressure, and UV radiation energy, simultaneously in vapour phase. To investigate the degradation effects after the outdoor exposure, jerrycans were exposed to a so called hydraulic internal pressure test, similar to an approval test for dangerous goods packaging. After combined impact of UV radiation and nitric acid, internal pressure tests showed very fast failures, whereas after separate impacts no remarkable deteriorations were observed, compared to unaged jerrycans. T2 - 19th IAPRI World conference on packaging CY - Melbourne, Australia DA - 15.06.2014 KW - High-density polyethylene HDPE KW - Nitric acid HNO3 KW - Outdoor exposure KW - UV radiation KW - Weathering PY - 2014 SN - 978-1-86272-699-4 SP - 556 EP - 560 AN - OPUS4-31222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - Surface temperatures of irradiated test specimens - decisive physical quantities and a largely unsolved problem N2 - Temperature is an important parameter in weathering tests. In many (photo-)chemical degradation processes a Variation of the specimen temperature by A t = + 1 °C can cause a Variation of AP(property change) by ± 8%. Since the early eighties it is well known that some types of black panel thermometers can show temperatures that are far below the maximum surface temperature of a black specimen. Although, there were precise requirements for the black coating of the BPT, a replacement by a white coating - depending on the design of the BPT - did not really change the temperature shown by the thermometer. There was no correlation between the BPT and the specimen surface temperature. In Europe and later at ISO the so-called black- and white-standard thermometers BST/WST were introduced. Now, there are BST and WST (ISO) and there are thermally uninsulated and insulated BPT and WPT (ASTM), partly for artificial or for outdoor exposure. And there are other adventurous procedures to determine surface temperatures. The different types of thermometers and different procedures will be discussed and it will be shown that there is no procedure which establishes a correlation between outdoor surface temperatures and surface temperatures in artificial exposure tests. T2 - 6th European weathering symposium Natural and artificial ageing of polymers CY - Bratislava, Slovak Republic DA - 11.09.2013 PY - 2013 SN - 978-3-9813136-8-0 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 16 SP - 185 EP - 194 AN - OPUS4-31292 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. A1 - Zäh, M. A1 - Schönlein, A. A1 - Müller, A. A1 - Vatahska, T. A1 - Manier, G. A1 - Reichert, T. ED - White, C. C. ED - Martin, J. ED - Chapin, J.T. T1 - Polypropylene numerical photoageing simulation by dose-response functions with respect to irradiation and temperature: vipquali project N2 - The aim of the joint project ViPQuali (Virtual Product Qualification) was to describe a component’s ageing behaviour in a given environment, by numerical simulation. Having chosen polypropylene (PP) as the material, which does not show sensitivity to moisture, the relevant weathering parameters of the dose–response functions could be limited to spectral irradiance and temperature. In artificial irradiation tests, for PP plates of varied stabiliser content, spectral sensitivity as well as temperature dependence of irradiation-caused crack formation was quantified. For that purpose, samples were exposed both to artificial weathering tests at various constant temperatures and to spectrally resolved irradiation. The temperature dependence could be modelled by an Arrhenius fit. For fitting the spectral sensitivity, a plateau function was chosen. Subsequently, the stabiliser content was parameterised and extrapolated. The formed dose–response functions were incorporated into a Computational Fluid Dynamics (CFD) software program, simulating the environment of a sample within a Phoenix-exposed IP/DP (Instrument Panel/Door Panel box) box, based on sun position and weather conditions, including radiation interactions. Observed local effects as well as the general ageing advance of PP hats are compared with respect to simulation and experiment. Resulting from this project, for this most simple example of PP of varied stabiliser content, the time to failure can be estimated for each weathering exposure environment with known time-resolved irradiance and temperature conditions. PY - 2015 SN - 978-3-319-06033-0 SN - 978-3-319-06034-7 DO - https://doi.org/10.1007/978-3-319-06034-7_14 SP - Chapter 14, 215 EP - 229 PB - Springer AN - OPUS4-32062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker T1 - Schadensanalyse im Bauwesen: Untersuchungen zu witterungsbedingten Schäden an einer polymeren Stadionverglasung T2 - PolymerTec 2014 (Veranstalter: Kunststoff-Kompetenzzentrum Halle-Merseburg, Insitut für Polymerwerkstoffe e. V.; Stiftung Akademie Mitteldeutsche Kunststoffinnovationen, Hochschule Merseburg) CY - Merseburg, Germany DA - 2014-06-25 PY - 2014 AN - OPUS4-30953 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Appajaiah, Anilkumar A1 - Wachtendorf, Volker A1 - Daum, Werner T1 - Climatic exposure of polymer optical fibers: Thermooxidative stability characterization by chemiluminescence N2 - The optical transmission stability was investigated for commercially available polymer optical fibers (POFs) which were exposed to a climate of 92°C and 95% relative humidity for about 3300 h. The optical transmission stability of POFs was correlated to their thermooxidative stability. POFs possessed identical core material, poly(methyl methacrylate), but they differed in the materials used for the claddings. The optical transmission was measured online using a prototype device called multiplexer. The chemiluminescence (CL) technique was applied to characterize the thermooxidative stability and degradation of POFs. CL analysis reveals the thermooxidative degradation of bare POFs (core and cladding), predominantly of the claddings, as a result of climatic exposure. Ultraviolet-visible transmittance measurements demonstrated more changes in the claddings as compared to the cores due to degradation. The CL and optical measurements data indicated that the optical transmission stability of POFs was dependent mainly on the thermooxidative stability of the claddings and their chemical compositions. KW - Ageing KW - Polymer optical fiber KW - Degradation KW - Chemiluminescence KW - Transparency PY - 2007 DO - https://doi.org/10.1002/app.23955 SN - 0021-8995 SN - 1097-4628 VL - 103 IS - 3 SP - 1593 EP - 1601 PB - Wiley InterScience CY - Hoboken, NJ AN - OPUS4-19072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Künstliche Bewitterungstests für polymere Beschichtungen T2 - TAW Symposium: "3. Korrosionsschutz-Symposium - Korrosionsschutz durch Beschichtungen in Theorie und Praxis" CY - Titisee-Neustadt, Germany DA - 2009-06-17 PY - 2009 AN - OPUS4-19590 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Spezifische Witterungsempfindlichkeiten verschiedener Kunststoffe im Außenbereich T2 - SKZ Fachtagung "Bewitterung von Kunststoffen und Lacken" CY - Würzburg, Germany DA - 2009-03-04 PY - 2009 AN - OPUS4-19591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Accelerated weathering test for plastics and coatings that are exposed to acidic precipitation T2 - 7th International Symposium on Weatherability (Proceedings ) CY - Yokohama, Japan DA - 2008-10-23 KW - Acid rain KW - ADF KW - Acid dew and fog test KW - Artificial weathering test PY - 2008 SP - 49 EP - 54 CY - Yokohama AN - OPUS4-21116 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Chemiluminescence for the early detection of weathering effects of coatings - Part I: Fundamentals KW - Chemiluminescence KW - Weathering KW - Polymer KW - Oxidation PY - 2010 SN - 1547-0083 VL - 7 IS - 4 SP - 66 EP - 71 PB - Federation of Societies for Coatings Technology CY - Blue Bell, Pa. AN - OPUS4-21493 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Chemiluminescence for the early detection of weathering effects of coatings - Part II: Experimental set-up and examination KW - Chemiluminescence KW - Weathering KW - Polymer KW - Oxidation PY - 2010 SN - 1547-0083 VL - 7 IS - 5 SP - 38 EP - 44 PB - Federation of Societies for Coatings Technology CY - Blue Bell, Pa. AN - OPUS4-21494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Determination of the spectral sensitivity and temperature dependence of polypropylene crack formation caused by UV-irradiation N2 - For polypropylene of varied stabilization, spectral sensitivity as well as temperature dependence of irradiation caused crack formation was determined in artificial irradiation tests. UV radiant exposure HUV necessary to generate crack formation was measured both in spectrally dispersed irradiation and artificial irradiation in a Fluorescent UV lamp device. Dependencies were fitted to a plateau function and an Arrhenius function, respectively, to describe the action of irradiation by response functions. Applied to weather data from Phoenix, the results were compared with respective outdoor exposure results. KW - Weathering KW - UV KW - Temperature KW - Numerical simulation PY - 2010 DO - https://doi.org/10.1016/j.polymdegradstab.2010.06.014 SN - 0141-3910 SN - 1873-2321 VL - 95 IS - 10 SP - 2118 EP - 2123 PB - Applied Science Publ. CY - London AN - OPUS4-21913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Alterungsvorgänge durch Bewitterung bei Beschichtungen und deren Untersuchung und Prüfung T2 - 42. Fortbildungskurs SAH - Holzoberflächen in der Fassadengestaltung CY - Weinfelden, Schweiz DA - 2010-10-26 KW - Bewitterung KW - Alterung KW - Holz PY - 2010 SN - 978-3-906703-26-8 SP - 29 EP - 38 CY - Zürich, Schweiz AN - OPUS4-22601 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Damerau, T. A1 - Hennecke, Manfred T1 - Degradation of poly(phenylphenylene-vinylene)-films during illumination and thermal treatment T2 - 5th Polymer Federation Symposium on Polymer Materials CY - Basel, Switzerland DA - 1994-10-09 PY - 1994 AN - OPUS4-23133 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Ziegahn, K.-F. T1 - Lebensdauerabschätzungen für Polypropylen durch Dosis-Wirkungsfunktionen bezüglich Bestrahlungsstärke und Temperatur (ViPQuali-Projekt) N2 - Für Polypropylen unterschiedlicher Stabilisierung wurden in künstlichen Bestrahlungstests sowohl die spektrale Empfindlichkeit als auch die Temperaturabhängigkeit der Rissbildung quantitativ ermittelt. Dafür wurde die Dauer bis zur Rissbildung sowohl bei spektraler Bestrahlung als auch bei Bestrahlung in einem UV-Leuchtstofflampengerät bei verschiedenen Temperaturen bestimmt. Die Temperaturabhängigkeit konnte als Arrhenius-Abhängigkeit beschrieben werden; das Wirkungsspektrum wurde an eine Stufenfunktion angepasst. Anschließend wurde auch noch der Einfluss des Stabilisatorgehalts als Potenzfit parametrisiert. Die Einzelabhängigkeiten wurden zu einer Gesamtfunktion der Wirkungen in Abhängigkeit der Dosis zusammengesetzt, die es ermöglicht die Wirkungen unterschiedlicher Dosiskombinationen abzuschätzen. Zur Validierung der Dosis-Wirkungsfunktionen wurden Freibewitterungsergebnisse aus Phoenix/Arizona herangezogen. Mit der Dosis, die sich aus den Wetterdaten dieser Freibewitterung ergibt, wurden anhand der Dosis-Wirkungs-Funktionen die jeweiligen Lebensdauern errechnet und mit dem experimentell bestimmten Versagen in der Freibewitterung verglichen. Die Arbeiten erfolgten im Rahmen des ViPQuali-Projektes mit dem Ziel der Bestimmung der Materialkenngrößen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe, Germany DA - 30.03.2011 KW - Bewitterung KW - UV KW - Lebensdauer KW - Simulation KW - Polypropylen PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 227 EP - 237 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-23474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Maskos, Michael A1 - Berger, Georg A1 - Braun, Ulrike A1 - Heyn, Andreas A1 - Klinger, Christian A1 - Wachtendorf, Volker T1 - Schadensanalyse und Beständigkeit von Materialien in biomedizinischen Einsatzgebieten N2 - Der Anteil von Polymeren als Funktions- und Konstruktionswerkstoffe in dauerhaften medizinischen Anwendungen steigt beständig. Derartige Materialien müssen den mechanischen, biologischen und chemischen Bedingungen im Körper widerstehen (u.a. Abrieb, Hydrolyse, Degradation) und gleichzeitig gut verträglich sein. Der sichere Einsatz von polymeren Materialien erfordert die Kenntnisse über ihre Langzeitstabilität unter verschiedenen äußeren Bedingungen. Diese sind nicht nur beeinflusst durch die unmittelbare Umgebung in vivo, sondern auch durch die Historie der verwendeten Materialien. Dazu zählen u. a. erhöhte Temperaturen unter sauerstoffhaltiger Atmosphäre während der Verarbeitung oder die Exposition von ionisierender Strahlung oder reaktiven Radikalen während der Sterilisation. PY - 2011 SP - 83 EP - 85 CY - Berlin AN - OPUS4-23592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Chancen und Grenzen der Verkürzung von Bewitterungstests durch empfindliche Chemilumineszenz-Detektion T2 - DFO Qualitätstage 2008, Appearance, Bewitterung, Korrosion, Farbe CY - Fürth, Germany DA - 2008-10-07 PY - 2008 AN - OPUS4-18710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Aussagekraft von Korrelationskoeffizienten T2 - 38. Jahrestagung der GUS CY - Stutensee-Blankenloch/Karlsruhe, Deutschland DA - 2009-03-18 KW - Witterungsbeständigkeit KW - Korrelation KW - Künstliche Bewitterung PY - 2009 SN - 978-3-9810472-7-1 SP - 61 EP - 70 CY - Pfinztal (Berghausen) AN - OPUS4-19161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Systematisierung der Alterungsvorgänge bei der Bewitterung von Polymerwerkstoffen T2 - 38. Jahrestagung der GUS CY - Stutensee-Blankenloch/Karlsruhe, Deutschland DA - 2009-03-18 KW - Witterungsbeständigkeit KW - Photochemische Alterung PY - 2009 SN - 978-3-9810472-7-1 SP - 51 EP - 60 CY - Pfinztal (Berghausen) AN - OPUS4-19162 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter T1 - Correlations in weathering results T2 - 4th European weathering symposium - Natural and artificial ageing of polymers CY - Budapest, Hungary DA - 2009-09-16 KW - Witterungsbeständigkeit KW - Korrelation KW - Künstliche Bewitterung KW - Artificial weathering PY - 2009 SN - 978-3-9810472-8-8 IS - Publication 11 SP - 251 EP - 261 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-20020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter T1 - Alterung von Polymeren durch Witterungsbeanspruchung T2 - 25. Darmstädter Kunststoff-Kolloquium, "Schadensanalytik heute - Methoden und Anwendungen" CY - Darmstadt, Germany DA - 2009-09-10 PY - 2009 AN - OPUS4-20573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter ED - Ziegahn, K.-F. T1 - Grundsätzliches zur Verkürzung von Bewitterungstests durch künstliche Bewitterung T2 - 35. Jahrestagung der GUS 2006 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Pfinztal, Deutschland DA - 2006-03-22 PY - 2006 SN - 3-9810472-0-6 SP - 165 EP - 175 PB - DWS Werbeagentur und Verlag GmbH CY - Pfinztal AN - OPUS4-21345 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, Peter ED - Ziegahn, K.-F. T1 - Ermittlung der Beanspruchung bei Bewitterungsversuchen - Referenzmaterialien T2 - 33. Jahrestagung der GUS 2004 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Pfinztal, Deutschland DA - 2004-03-17 PY - 2004 SN - 3-9808382-4-2 SP - 165 EP - 175 PB - DWS Werbeagentur und Verlag GmbH CY - Pfinztal AN - OPUS4-21346 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Trubiroha, Peter A1 - Wachtendorf, Volker A1 - Geburtig, Anja ED - Ziegahn, K.-F. T1 - Beispiele für die Nutzung des Energietransports durch langwellige (thermische) Strahlung T2 - 35. Jahrestagung der GUS 2006 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Pfinztal, Deutschland DA - 2006-03-22 PY - 2006 SN - 3-9810472-0-6 SP - 205 EP - 214 PB - DWS Werbeagentur und Verlag GmbH CY - Pfinztal AN - OPUS4-21347 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schulz, Ulrich A1 - Wachtendorf, Volker A1 - Geburtig, Anja ED - Reichert, T. T1 - The influence of mildew growth on automotive coatings on the results of outdoor weathering T2 - 1st European weathering symposium - Natural and artificial ageing of polymers CY - Prague, Czech Republic DA - 2003-09-25 PY - 2003 SN - 3-9808382-5-0 VL - 5/2004 IS - Session 7 SP - 357 EP - 374 PB - DWS Werbeagentur und Verlag GmbH CY - Pfinztal AN - OPUS4-21348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Ulrich A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Pinholes - the negative impact of mildew growth PY - 2004 SN - 0930-3847 VL - 5 SP - 26 EP - 30 PB - Vincentz CY - Hannover AN - OPUS4-21350 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Zäh, M. A1 - Schönlein, A. A1 - Reichert, T. T1 - Polypropylene life time estimation by developing dose response functions with respect to irradiation and temperature - ViPQuali project T2 - 8th International symposium on weatherability (8th ISW) CY - Tokyo, Japan DA - 2010-10-14 KW - Life time estimation KW - Weathering KW - Polypropylene KW - Spectral sensitivity KW - Temperature PY - 2010 SN - 1346-0633 VL - 22 SP - 58 EP - 63 PB - Uni Publishers Co., Ltd. AN - OPUS4-22182 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Die Kunst der Fuge im Glasfassadenbau N2 - Ingenieurbauwerke wie Brücken, hoch beanspruchte Verkehrsflächen oder auch Hochhäuser und deren Bauwerksteile wie z.B. Hochhausfassaden werden aus technischen und ästhetischen Gründen durch Fugen in Einzelabschnitte unterteilt. Zur Sicherstellung der Gebrauchsfähigkeit und zum Schutz des Gesamtbauwerks, aber in zunehmendem Maße auch zur statisch-konstruktiven Anbindung der Bauwerksteile, werden diese Fugenspalte in aller Regel durch spezielle Fugenfüllsysteme verschlossen. Aufgrund der hohen Sicherheitsrelevanz bei Fugenfüllungen im Glasfassadenbau fordert das Baurecht auch bei diesen Bauprodukten als Voraussetzung für die baupraktische Verwendbarkeit neben dem Nachweis der Funktionsfähigkeit auch den Nachweis der Dauerhaftigkeit. Da die hierfür bekannten Nachweismethoden zur Dauerhaftigkeit keine allgemeine Zulassungsakzeptanz finden, kann das ästhetische, bauphysikalische und ökonomische Potential von modernen geklebten Ganzglasfassaden (sogenannte SSG-Fassaden) in der Baupraxis der Bundesrepublik Deutschland derzeit nicht ausgenutzt werden. Grund dafür sind die ungenügend erfassten und in den Bewertungsverfahren simulierten Wechselwirkungen derartiger Baukonstruktionen mit der Umwelt. In diesem Beitrag soll am Beispiel moderner Fugen im Glasfassadenbau (SSG-Fassaden) eine ganzheitliche gebrauchsbezogene Versuchsmethodik zur kontrollierten Ansprache der Funktionsfähigkeit und Dauerhaftigkeit von Fugensystemen unter realitätsnah und reproduzierbar simulierten Umwelteinwirkungen vorgestellt werden. Dazu werden die maßgebenden Umwelteinflüsse und die Quantifizierung der daraus folgenden Beanspruchungen auf derartige Fugensysteme dargestellt. Basierend darauf werden eine repräsentative Beanspruchungsfunktion zur Nachstellung der maßgebenden Umwelteinflüsse und Beanspruchungen auf das System Tragrahmen - Fugenfüllung- Glasscheibe sowie eine geeignete Probendimensionierung abgeleitet. In der Konsequenz werden die Erkenntnisse in den Aufbau einer neuartigen komplexen Versuchseinrichtung überführt. Funktionsprinzip und Leistungsparameter dieser Anlage zur Umweltsimulation werden vorgestellt. Die Möglichkeiten der Systemkennzeichnung werden vorgestellt. Erste Versuchsergebnisse zeigen das Potential der neuartigen Bewertungsmethodik auf, die Kunst der Fuge im Bauwesen gebrauchsorientiert weiter zu entwickeln. T2 - 44. Jahrestagung der GUS 2015 CY - Stutensee-Blankenloch, Germany DA - 25.03.2015 KW - Umweltsimulation KW - Dauerhaftigkeit KW - Funktionsverhalten KW - Neue Untersuchungsmethodik PY - 2015 SN - 978-3-9816286-4-7 SP - 125 EP - 139 AN - OPUS4-33040 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - On the yet unsolved problem of the determination of precise surface temperatures of specimens exposed to natural and artificial weathering N2 - The surface temperature of test specimens exposed to natural and artificial solar radiation are roughly ascertained with black standard thermometers BST and white standard thermometers WST. For the calibration of these thermometers a new European Standard prEN 16465 was published in 2015, describing the well-known contact method and a new contactless method with a pyrometer. It can be confirmed that the temperature calibrations according to the two methods provide different calibration results which are not interchangeable (which is already stated in the scope of this standard). The described contactless method to determine the surface temperature 'under radiation load' results in clearly too high temperatures. This paper tries to highlighting the reasons. T2 - 7th European weathering symposium - Natural and artificial ageing of polymers CY - Naples, Italy DA - 16.09.2015 PY - 2015 SN - 978-3-9816286-6-1 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 17 SP - 23 EP - 36 AN - OPUS4-34351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Goedecke, Thomas A1 - Wachtendorf, Volker ED - Reichert, T. T1 - A new irradiation device for medium scale plastic products N2 - A new irradiation device for the exposure of plastic products is presented. Developed in the BAM division 3.1 "Dangerous Goods Packaging" it can be used for artificial UV irradiation of plastic Containers filled with hazardous liquids. Present regulations and tests only investigate the exposure effects of UV and of media separately, but as the damaging effect is expected to be synergistic for at least some media, a combined test was looked for. A chamber of 60 cm by 60 cm base area and 1 m height gives space for up to 40 cm wide objects. Two fluorescent UV lamp arrays are arranged on opposite walls, separated from the chamber by quartz glass panes. By continuously rotating the exposure object by means of a rotary disc that the object is placed on, spatial irradiation homogeneity is achieved over the exposure duration. The spectral irradiance of the chosen UVA 340 nm lamps gives the best match of global solar radiation in the short wavelength ränge. The close arrangement of the UVA lamps (15 each side) results in 60 W m'2 UV irradiance. Constant temperature is adjusted to typically 40 °C by the control of the fan speed. This temperature is chosen, as it is the required temperature for three week storage of filled polyethylene Containers, for proving Chemical compatibility in the field of dangerous goods. To ensure homogeneity, an interiorfan provides for air circulation. T2 - 7th European weathering symposium - Natural and artificial ageing of polymers CY - Naples, Italy DA - 16.09.2015 KW - Weathering KW - UV irradiation PY - 2015 SN - 978-3-9816286-6-1 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 17 SP - 91 EP - 96 AN - OPUS4-34353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Schulz, Ulrich A1 - Trubiroha, Peter T1 - „Test Tailoring“ eines künstlichen Bewitterungstests am Beispiel der Entwicklung des „Acid Dew and Fog“ Testes N2 - Häufig ist es wünschenswert, für neue Materialien oder Anwendungen künstliche Bewitterungsverfahren zu benutzen, die auf die spezifischen Anforderungen besser zugeschnitten sind, als es bei bestehenden standardisierten Verfahren der Fall ist. Nachdem man die spezifischen Parameter der Beanspruchung unter Anwendungsbedingungen und die spezifische Empfindlichkeit des Materials erfasst hat, beginnt ein Prozess, der als „Test Tailoring“ häufig abstrakt verwendet, auf den aber nur selten näher eingegangen wird. Genau dieser Prozess soll hier am Beispiel der Entwicklung eines künstlichen Bewitterungstests unter saurer Beaufschlagung, dem in der BAM entwickelten Acid Dew and Fog Test, beispielhaft erläutert werden. T2 - 47. Jahrestagung der GUS 2018, Umwelteinflüsse erfassen, simulieren, bewerten CY - Pfinztal (Berghausen), Germany DA - 21.03.2018 KW - Test Tailoring KW - Bewitterung KW - Acid Dew and Fog KW - Umweltsimulation PY - 2018 VL - 47 SP - Vortrag V4, 45 EP - 54 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal AN - OPUS4-45412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Fischer, C. A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane T1 - Active thermography for quality assurance of 3D-printed polymer structures N2 - Additively manufactured test specimens made of polyamide 12 (PA 12) by Laser Sintering (LS) as well as of acrylnitril-butadien-styrol (ABS) by Fused Layer Modeling (FLM), were tested with active thermography. For this, two different excitation methods (flash and impulse excitation) were used and compared, regarding the suitability for the detection of constructed and imprinted defects. To increase the quality of the thermograms, data processing methods like thermal signal reconstruction (TSR) and Fourier-Transformation were applied. Furthermore, the long-term stability of the probes towards environmental stress, like UV-radiation, heat, water contact and frost is being investigated in the presented project with artificial weathering tests. T2 - 14th Quantitative InfraRed Thermography Conference CY - Berlin, Germany DA - 25.06.2018 KW - Additive manufacturing KW - Active thermography KW - Artificial weathering PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-453919 SP - Tu.3.A.2, 1 EP - 9 AN - OPUS4-45391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane A1 - Fischer, C. ED - Ziegahn, K.-F. T1 - Additiv gefertigte Polymerbauteile: Untersuchung der Beständigkeit durch künstliche Bewitterung und zerstörungsfreie Charakterisierung N2 - Es wird ein Verfahren zur Charakterisierung der Beständigkeit und Langzeitstabilität von additiv gefertigten Kunststoff-Bauteilen vorgestellt. Dabei sollen die Prüfkörper über 2000 Stunden künstlich bewittert und währenddessen die Änderungen der Eigenschaften der Bauteile zerstörungsfrei untersucht werden. T2 - 47. Jahrestagung der Gesellschaft für Umweltsimulation e.V. CY - Stutensee, Germany DA - 21.03.2018 KW - Additive Fertigung KW - Künstliche Bewitterung KW - Thermografie KW - Additive manufacturing PY - 2018 VL - 47. SP - 99 EP - 105 PB - Gesellschaft für Umweltsimulatin e.V. AN - OPUS4-44638 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Franz, Philipp A1 - Metz, Christain A1 - Brackrock, Daniel A1 - Fischer, C. A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane T1 - Zerstörungsfreie Charakterisierung und Qualitätssicherung der Materialeigenschaften und Beständigkeit additiv gefertigter Kunststoffteile N2 - Mit additiven Fertigungsverfahren hergestellte Bauteile und Produkte aus Kunststoffen werden zunehmend nicht mehr nur als Prototypen, sondern als voll funktionsfähige Bauteile und Produkte gefertigt. Bedingt durch die Fertigungsprozesse und den schichtweisen Aufbau resultieren physikalische Materialeigenschaften, die stark von den Fertigungsparametern abhängen und zudem anisotrop sind. Von den Fertigungsparametern werden auch die Oberflächeneigenschaften beeinflusst, sodass zu erwarten ist, dass sich die Beständigkeit gegenüber äußeren Umwelteinflüssen bei additiv gefertigten Bauteilen von der konventionell gefertigter unterscheiden kann. Nachfolgend wird daher die Entwicklung eines Qualitätssicherungskonzeptes basierend auf spektroskopischen und zerstörungsfreien Prüfverfahren vorgestellt, in dem der Alterungsprozess von mittels Fused Deposition Modelling (FDM) und mittels Lasersintering (LS) hergestellten Probekörpern untersucht wird. T2 - DGZfP-Jahrestagung 2018 CY - Leipzig, Germany DA - 07.05.2018 KW - Additive Fertigung KW - Kunststoffe KW - Zerstörungsfreie Prüfung PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-449016 SN - 978-3-940283-92-4 VL - DGZfP BB 166 SP - Mo.2.A.1, 1 EP - 9 AN - OPUS4-44901 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Wachtendorf, Volker A1 - Elert, Anna Maria A1 - Weidner, Steffen T1 - Effects of UV radiation on the friction behavior of thermoplastic polyurethanes N2 - The effects of weathering exposure on unfilled and filled thermoplastic polyurethanes (TPU) materials are described as performed under different humidity conditions. For this purpose, a weathering device was used with UV-A 340 nm lamps at a constant temperature of 40 °C. The effects of environmental (UV and humidity condition) degradation on the frictional properties of TPU materials are presented along with surface analyses to characterize the chemistry of the degradative process. Photooxidative degradation of unfilled polymer leads to deterioration of physical and mechanical properties, which affects its tribological behavior significantly. Due to crosslinking, the stiffness of the material increases, reducing drastically the friction coefficient of unfilled TPUs. The frictional behavior of glass fiber reinforced TPU is less affected by radiation. KW - Photooxidation KW - UV radiation KW - Friction KW - TPU KW - Humidity PY - 2018 DO - https://doi.org/10.1016/j.polymertesting.2018.08.006 SN - 0142-9418 SN - 1873-2348 VL - 70 SP - 467 EP - 473 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-45709 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Exposure response function for a quantitative prediction of weathering caused aging of polyethylene N2 - The exposure response function of the carbonyl formation over the bulk has been determined for a high-density polyethylene of a thickness of 200 μm, which was used as a weathering reference material according to ISO TR 19032. To this end, spectral sensitivity was studied by local measurement of the effect of spectrally dispersed irradiation. Both the exposure device and the methodology of determination are described. The temperature dependency of photooxidation was determined by UV exposure at various temperatures between 23 and 80 °C. Deviations from linearity and thus reciprocity below 40 °C are discussed and assumed to be related to diffusion limitations. An Arrhenius approach –based on data of linear carbonyl formation – has been incorporated into the exposure response function. Using this exposure response function, aging in terms of the distribution of a quantitative property change over a plastic component can be predicted for a specific outdoor location with real chronologic weather data as input for the exposure. Thus, artificial and natural weathering can be linked and compared. The established exposure response function has been validated by outdoor exposure results from the literature. If an estimated diffusion limitation is taken into consideration, calculations and published data are in good agreement. KW - Irradiation KW - Weathering KW - Spectral sensitivity KW - Temperature dependency KW - Spectral irradiation PY - 2019 DO - https://doi.org/10.3139/120.111348 SN - 0025-5300 VL - 61 IS - 6 SP - 517 EP - 526 PB - Carl Hanser Verlag GmbH & Co. KG AN - OPUS4-48295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erdmann, Maren A1 - Kleinbub, Sherin A1 - Wachtendorf, Volker A1 - Schütter, Jan David A1 - Niebergall, Ute A1 - Böhning, Martin A1 - Koerdt, Andrea T1 - Photo-oxidation of PE-HD affecting polymer/fuel interaction and bacterial attachment N2 - In the present study, a simple approach was used to investigate the effect of UV-exposure on two high density Polyethylene materials (PE-HD), commonly used for storage tanks, on fuel sorption behavior and colonization by microorganisms. The aim was to investigate whether the sorption behavior of the fuels (diesel/biodiesel) and the colonization by microorganisms, frequently occurring in the fuel, is affected and may lead to undesirable or safety-relevant material changes. We showed that the UV-irradiation leads to significant changes of the sorption behavior due to chemi-crystallization and crosslinking. The fuel Sorption is affected by the UV-induced formation of polar carbonyl and hydroxyl groups predominantly occurring at the surface. With respect to microbial colonization behavior for Bacillus subtilis and Pseudomonas aeruginosa, isolated from a contaminated diesel sample, differences of the initial adhesion could be shown depending on the initial type of polyethylene as well as on the degree of UV-induced degradation. KW - High density polyethylene KW - Bacterial attachment KW - UV-irradiation KW - Fuel sorption PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-510001 DO - https://doi.org/10.1038/s41529-020-0122-1 VL - 4 IS - 1 SP - Article number: 18 PB - Nature Partner Journals AN - OPUS4-51000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erdmann, Maren A1 - Niebergall, Ute A1 - Wachtendorf, Volker A1 - Böhning, Martin T1 - Evaluation of UV-induced embrittlement of PE-HD by Charpy impact test N2 - The impact fracture behavior of two common high-density polyethylene grades for container applications were intensively studied by the instrumented Charpy impact test after well-defined exposure to UV-irradiation. Individual stages of the impact event, such as crack initiation and crack propagation energy as well as maximum impact load, were investigated from the recorded load–deflection curves. UV-induced material property changes were further investigated by infrared spectroscopy, differential scanning calorimetry, and dynamic-mechanical analysis as well as density measurements. Based on the results of the Charpy impact test, three indicators were identified to describe the extend of photooxidation on high-density polyethylene: (a) a reduced Charpy impact strength—at least to half of its initial value for a distinctly brittle impact fracture, (b) a marked decrease in the crack propagation contribution to the impact strength, and (c) an increase of the brittle features of the fracture surface. KW - Degradation KW - Mechanical properties KW - Packaging KW - Polyolefins KW - Polyethylene PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509130 DO - https://doi.org/10.1002/APP.49069 SN - 0021-8995 VL - 137 IS - 36 SP - 49069 PB - Wiley AN - OPUS4-50913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niebergall, Ute A1 - Zanotto, M. A1 - Wachtendorf, Volker A1 - Böhning, Martin T1 - Impact of biodiesel sorption on tensile properties of PE-HD for container applications N2 - In previous papers, we investigated the influence of biodiesel or diesel on mechanical properties of a high-density polyethylene (PE-HD) for tank applications using Charpy impact tests and dynamicmechanical analysis (DMA). In this work, covering two more PE-HD materials, we extend our study to addressing the tensile properties, especially changes of Young's modulus, after immersion in biodiesel or diesel at 60 °C. As we cover sorption and desorption behavior, during desorption, i.e. storage at 60 °C in a circulating air oven, ageing or degradation phenomena were also observed and characterized in some detail using spectral reflectance measurements and FT-IR spectroscopy. The results obtained here support the concept of co-oxidation, i.e. the faster oxidation of the PE-HD matrix if the samples were previously saturated with biodiesel, itself easily oxidizable. KW - polyethylene KW - biodiesel KW - biofuels KW - sorption KW - plasticization KW - degradation PY - 2016 DO - https://doi.org/10.1016/j.polymertesting.2016.01.025 SN - 0142-9418 VL - 50 SP - 315 EP - 324 PB - Elsevier AN - OPUS4-35369 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Goedecke, Thomas ED - Ziegahn, K.-F. T1 - Beanspruchung von HDPE-Verpackungsproben durch UV-Strahlung und Salpetersäure N2 - Transport und Lagerung flüssiger Chemikalien erfolgen häufig in HDPE-Behältern. Diese Behälter müssen Bauteilprüfungen bestehen, die mechanische und chemische Beanspruchungen kombinieren. UV-Beanspruchungen sind kein Bestandteil der Zulassungsprüfungen; gefordert wird aber eine ausreichende UV-Stabilisierung. Inwiefern diese UV-Stabilisierung aber abhängig vom jeweiligen Füllgut ist, soll hier untersucht werden. Vorgestellt wird der experimentelle Aufbau zur kombinierten Beanspruchung von Kunststoffproben durch UV-Strahlung und flüssige Chemikalien. Aufgrund des Gefährdungspotenzials sind dabei entsprechende Sicherheitsvorgaben einzuhalten. Ziel ist die Bewertung synergistischer Effekte beider Einzelbeanspruchungen. Die Wirksamkeit verschiedener Stabilisierungskonzepte bei Beanspruchung durch 55 %-ige Salpetersäure wird beleuchtet. Es wird anschaulich gezeigt, dass nur pigmentiertes HDPE ausreichende Stabilität aufweist. T2 - 43. Jahrestagung der GUS 2014 CY - Stutensee-Blankenloch, Germany DA - 26.03.2014 PY - 2014 SN - 978-3-9816286-0-9 SP - Kap. V 5, 45 EP - 51 AN - OPUS4-31136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Discussion on Weathering Reference Materials N2 - Weathering reference materials (WRMs) are used to characterize the harshness of an exposure, aiming on either reproducibility of a specific exposure or on the comparability between various kinds of natural or artificial weathering exposure. The materials that are used as weathering reference materials differ in their sensitivities (as well as in interactions and interferences of the latter), conditioned by the different processes which lead to the respective property change. It is also essential to take into account the necessary measurement equipment for the respective property change, in order to allow timely intervention. What are the key issues on choosing a weathering reference material? What can be learned from the weathering reference materials, investigated so far? Possibilities and limitations are discussed on the basis of existing weathering reference materials. Conclusions are drawn, for establishing new weathering reference materials. T2 - 9th European Weathering Symposium CY - Basel, Switzerland DA - 18.09.2019 KW - Temperature dependency KW - Weathering KW - Irradiation KW - Spectral sensitivity PY - 2019 SN - 978-3-9818507-5-8 SP - 283 EP - 292 PB - Thomas Würtz Grafik-Design CY - Karlsruhe, Germany AN - OPUS4-49150 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - 40 Years of Global-UV-Test weathering device: with fluorescent UV lamps and a precise microclimatical control into the future N2 - On the basis of a lot of investigation on the spectral sensitivity of photo degradation of plastics and on the underestimated influence of temperature and relative humidity on degradation processes a new type of weathering device was presented at the end of the seventies: It was a combination of a radiation source with fluorescent UV lamps and a precise climatic cabinet. The radiation emission from a combination of four different types of fluorescent UV lamps was superimposed on the specimen surfaces in the climatic cabinet to match the UV part of solar radiation as closely as possible. Air temperature was controlled to within ± 1 °C, and relative humidity to within ± 5 %RH. As the lamps’ emission is focussed on the UV range almost no radiation heating of the sample occurs. Therefore, the temperature of the sample, which is the quantity of consideration for the degradation, is nearly identical with the chamber’s air temperature, which is the quantity to be controlled. Also, therefore, high humidity can be obtained on the sample surface. The limitation of the emission to the UV range is sufficient for the study of the polymer matrix. This type of weathering device offers an exactness of microclimatic control of the sample’s surface, which should be a standard for weathering devices. Even now it is the only weathering device which generates pure relative humidity (without aerosol). T2 - 9th European Weathering Symposium CY - Basel, Switzerland DA - 18.09.2019 KW - Weathering KW - Irradiation PY - 2019 SN - 978-3-9818507-5-8 SP - 37 EP - 47 PB - Thomas Würtz Grafik-Design CY - Karlsruhe, Germany AN - OPUS4-49151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, P. T1 - Application of a newly proposed sensor for effective UV-irradiance for the monitoring of both natural and artificial weathering conditions N2 - To improve on the classic radiometric sensor with radiometric measurement [ ] here a new UV-sensor characteristic for effective UV is proposed that no longer applies equal weighting of spectral irradiation into the UV irradiance value but rather aims at approaching a weighting according to a typical spectral sensitivity curve of polymers. This curve resembles the erythema curve of the skin which is the basis of the UV-index. For the use of the sensor it would be desirable to keep it in the artificial weathering device for the complete weathering test (including rain phases) while the same sensor should also be applicable for the monitoring of outdoor weathering exposures. A first application of this kind of weighted measurement and a comparison with radiometric measurements accompanied with polymer ageing results will be presented together with conclusions for a future effective UV irradiance sensor. T2 - 9th European Weathering Symposium CY - Basel, Switzerland DA - 18.09.2019 KW - UV-irradiance PY - 2019 SN - 978-3-9818507-5-8 VL - 19 SP - 293 EP - 306 AN - OPUS4-49154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Fischer, C. A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane T1 - Zerstörungsfreie Charakterisierung der Alterung additiv gefertigter Kunststoffbauteile N2 - Das vorgestellte Projekt beschäftigt sich mit den optischen, thermophysikalischen und mechanischen Materialeigenschaften von additiv gefertigten Kunststoffteilen und deren Alterung. Dazu wurden mittels Fused Layer Modeling (FLM) Probekörper aus ABS hergestellt, die anschließend für drei Monate einer künstlichen Bewitterung unterzogen wurden. Die dabei erzeugte definierte Alterung wurde nach drei Zeitabschnitten jeweils mit zerstörungsfreien Methoden charakterisiert. Dabei wurde neben den spektroskopischen Standardmethoden auch die aktive Thermografie eingesetzt. Die Ergebnisse zeigen, dass sich mittels der Thermografie sowohl chemische Veränderungen als auch mechanische Schädigungen (Fehlstellen) darstellen lassen. Die Bewitterung beeinflusst die Teiltransparenz der Proben zumindest im sichtbaren Spektralbereich, was bei der Charakterisierung der Fehlstellen, die mittels optisch angeregter aktiver Thermografie detektiert wurden, berücksichtigt werden muss. T2 - DGZfP-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - 3D Druck KW - Additive Fertigung KW - Thermografie KW - Polymere KW - Künstliche Bewitterung PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-491561 UR - https://jt2019.dgzfp.de/Portals/jt2019/bb/Di.3.B.1.pdf SN - 978-3-947971-02-2 VL - 171 SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-49156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Maierhofer, Christiane A1 - Wachtendorf, Volker A1 - Fischer, C. ED - Ziegahn, K.-F. T1 - Untersuchung der Beständigkeit additiv gefertigter Bauteile durch Thermografie nach künstlicher Bewitterung N2 - Additiv gefertigte Prüfkörper aus Polyamid 12 (Laser Sinter Verfahren) und Acrylnitril-Butadien-Styrol (Fused Layer Modeling Verfahren) wurden über 2000 Stunden künstlich bewittert und ihr Alterungsverhalten untersucht. Die Ergebnisse wurden anschließend mit denen von Prüfkörpern verglichen, welche auf dieselbe Weise künstlich bewittert, aber mittels konventionellem KunststoffSpritzguss hergestellt wurden. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Germany DA - 27.03.2019 KW - Polymere KW - Additive Fertigung KW - 3D Druck KW - Künstliche Bewitterung KW - Thermografie PY - 2019 SN - 978-3-9818507-3-4 VL - 48 SP - 207 EP - 216 CY - Pfinztal (Berghausen) AN - OPUS4-48502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Metz, Christian A1 - Franz, Philipp A1 - Fischer, C. A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane T1 - Active thermography for quality assurance of 3D-printed polymer structures N2 - Additively manufactured test specimens made of polyamide 12 (PA 12) by Laser Sintering as well as of acrylonitrile butadiene styrene (ABS) by Fused Layer Modelling, were characterised with active thermography directly after manufacturing and after artificial weathering. For this, two different excitation methods (flash and pulse heating) were used and compared, regarding their suitability for the detection of constructed and imprinted defects inside the test specimens. To increase the quality of the thermograms, data processing methods like thermal signal reconstruction (TSR) and Fourier Transformation after TSR were applied. To further investigate the long-term stability of the additively manufactured test specimens towards environmental stress, like UV radiation, heat, humidity, water contact and frost with active thermography, an artificial weathering test over 2000 hours (~3 months) was applied to the specimens. The monitoring of the changes in the optical properties of the weathered plastics was supplemented by spectral reflectance and UV/VIS spectroscopy. KW - Additive manufacturing KW - Polymers KW - Artificial weathering KW - Active thermography KW - UV/VIS spectroscopy PY - 2019 DO - https://doi.org/10.1080/17686733.2019.1686896 SN - 1768-6733 (Print) 2116-7176 (Online) VL - 18 IS - 1 SP - 50 EP - 72 PB - Taylor & Francis AN - OPUS4-49817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Elert, Anna Maria A1 - Weidner, Steffen T1 - Einfluss von Feuchte und Nässe auf die Witterungs-induzierte Alterung am Beispiel eines Polyurethans N2 - Bei der Bewitterung von Polymeren kommt es auf molekularer Ebene zur Alterung, die sich in verschiedenen Eigenschaften als unterschiedlich starke Änderung äußert. Art und Geschwindigkeit dieser molekularen Alterung und die damit einhergehenden Eigenschaftsänderungen hängen dabei neben einer Reihe anderer Einflussfaktoren von der Art und Intensität der Beanspruchung ab. In diesem Beitrag soll der relative Einfluss des Wassers als Feuchte und Nässe unter den Beanspruchungsfaktoren untersucht werden. Die Unterscheidung von Luftfeuchte und Nässe bezüglich ihrer Wirkung ist dabei notwendig, weil die stehende Nässe zusätzliche Extraktionswirkung besitzt und auch die verfügbare Sauerstoffmenge beeinflusst. Dazu wurde ein Polymer, das im Rahmen des BAM-internen Projektes PolyComp untersucht wird, künstlich bewittert. Hierzu wurde ein Fluoreszenzlampengerät mit UV-A 340 nm Leuchtstoffröhren verwendet, in dessen Probenraum durch zusätzliche Kammern die gleichzeitige Bewitterung unter drei unterschiedlichen Feuchte-Varianten realisiert wurde (bei konstanter Temperatur): - UV und trocken - UV und hohe Luftfeuchte - UV und stehende Nässe. Das gleichzeitige Einwirken der einzelnen Einflussfaktoren kann dabei konkurrierende oder aufeinander folgende chemische Reaktionen und physikalische Prozesse und somit ein anderes Ergebnis bewirken, als wenn sie isoliert nacheinander auf eine Probe eingewirkt hätten. Über die erwähnten Varianten hinaus kann auch noch der spezifische Einfluss der UV-Strahlung mit untersucht werden, weil die Proben im Bereich ihrer Befestigung verdeckt sind. Die Methodik und erste Ergebnisse dieser Untersuchung werden präsentiert. T2 - 46. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) 2017 CY - Stutensee-Blankenloch bei Karlsruhe, Germany DA - 22.03.2017 KW - Polyurethan KW - TPU KW - Bewitterung KW - Feuchte KW - Nässe KW - UV PY - 2017 AN - OPUS4-39905 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Elert, Anna Maria A1 - Weidner, Steffen T1 - Einfluss von Feuchte und Nässe auf die Witterungs-induzierte Alterung am Beispiel eines Polyurethans N2 - In diesem Beitrag soll der relative Einfluss des Wassers als Feuchte und Nässe unter den Beanspruchungsfaktoren untersucht werden. Die Unterscheidung von Luftfeuchte und Nässe bezüglich ihrer Wirkung ist dabei notwendig, weil die stehende Nässe zusätzliche Extraktionswirkung besitzt und auch die verfügbare Sauerstoffmenge beeinflusst. Dazu wurde ein Polymer, das im Rahmen des BAM-internen Projektes PolyComp untersucht wird, künstlich bewittert. Hierzu wurde ein Fluoreszenzlampengerät mit UV-A 340 nm Leuchtstoffröhren verwendet, in dessen Probenraum durch zusätzliche Kammern die gleichzeitige Bewitterung unter drei unterschiedlichen Feuchte-Varianten realisiert wurde (bei konstanter Temperatur): - UV und trocken - UV und hohe Luftfeuchte - UV und stehende Nässe Das gleichzeitige Einwirken der einzelnen Einflussfaktoren kann dabei konkurrierende oder aufeinander folgende chemische Reaktionen und physikalische Prozesse und somit ein anderes Ergebnis bewirken, als wenn sie isoliert nacheinander auf eine Probe eingewirkt hätten. Über die erwähnten Varianten hinaus kann auch noch der spezifische Einfluss der UV-Strahlung mit untersucht werden, weil die Proben im Bereich ihrer Befestigung verdeckt sind. Die Methodik und erste Ergebnisse dieser Untersuchung werden präsentiert. T2 - 46. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) 2017 CY - Stutensee-Blankenloch bei Karlsruhe, Germany DA - 22.03.2017 KW - Polyurethan KW - TPU KW - Bewitterung KW - UV KW - Feuchte KW - Nässe PY - 2017 SN - 978-3-9816286-9-2 VL - 46 SP - 251 EP - 261 PB - Gesellschaft für Umweltsimulation e. V CY - Pfinztal (Berghausen) AN - OPUS4-39906 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Quantitative Auswertemöglichkeiten bei der spektralen Bestrahlung – Berechnung des Wirkungsspektrums N2 - Für die Bewertung des Wellenlängeneinflusses auf die Alterungsvorgänge bei der Bestrahlung UV- oder lichtempfindlicher Materialien kann die Methode der spektralen Bestrahlung angewendet werden. Im Prinzip wird dabei das linear dispergierte Spektrum einer Strahlenquelle mit kontinuierlichem Spektrum (z.B. Xe-Lampe) auf eine Probenoberfläche abgebildet, so dass Ort einer Materialänderung und Wellenlänge der Bestrahlung einander zugeordnet werden können. Nachfolgende lokal-auflösende Analysemethoden ermitteln eine Eigenschaftsänderung an einem spezifischen Ort der Probe, aus dem sich dann die Bestrahlungswellenlänge ergibt. Der verwendete Aufbau wird beschrieben. Es wird an einem ausgewählten Beispiel gezeigt, wie durch geeignete Anbindung eines Messsystems zur Bestimmung der spektralen Bestrahlungsstärke und ortsaufgelöste Messungen der Eigenschaftsänderungen eine quantitative Auswertung realisiert werden kann. Der Einfluss nichtlinearer Alterungsverläufe wird diskutiert. Grenzen der Methode werden aufgezeigt und Erweiterungsmöglichkeiten dargestellt. T2 - 46. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 22.03.2017 KW - Bewitterung KW - Spektrale Bestrahlung KW - Kunststoffe PY - 2017 SN - 978-3-9816286-9-2 SP - 91 EP - 99 AN - OPUS4-39595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. ED - Ziegahn, K.-F. T1 - Quantitative Auswertemöglichkeiten bei der spektralen Bestrahlung – Berechnung des Wirkungsspektrums N2 - Für die Bewertung des Wellenlängeneinflusses auf die Alterungsvorgänge bei der Bestrahlung UV- oder lichtempfindlicher Materialien kann die Methode der spektralen Bestrahlung angewendet werden. Im Prinzip wird dabei das linear dispergierte Spektrum einer Strahlenquelle mit kontinuierlichem Spektrum (z.B. Xe-Lampe) auf eine Probenoberfläche abgebildet, so dass Ort einer Materialänderung und Wellenlänge der Bestrahlung einander zugeordnet werden können. Nachfolgende lokal-auflösende Analysemethoden ermitteln eine Eigenschaftsänderung an einem spezifischen Ort der Probe, aus dem sich dann die Bestrahlungswellenlänge ergibt. Der verwendete Aufbau wird beschrieben. Es wird an einem ausgewählten Beispiel gezeigt, wie durch geeignete Anbindung eines Messsystems zur Bestimmung der spektralen Bestrahlungsstärke und ortsaufgelöste Messungen der Eigenschaftsänderungen eine quantitative Auswertung realisiert werden kann. Der Einfluss nichtlinearer Alterungsverläufe wird diskutiert. Grenzen der Methode werden aufgezeigt und Erweiterungsmöglichkeiten dargestellt. T2 - 46. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 22.03.2017 KW - UV-Bestrahlung PY - 2017 SN - 978-3-9816286-9-2 SP - V 8, 91 EP - 99 AN - OPUS4-42578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kömmling, Anja A1 - Chatzigiannakis, E. A1 - Beckmann, Jörg A1 - Wachtendorf, Volker A1 - von der Ehe, Kerstin A1 - Braun, Ulrike A1 - Jaunich, Matthias A1 - Schade, U. A1 - Wolff, Dietmar T1 - Discoloration Effects of High-Dose gamma-Irradiation and Long-Term Thermal Aging of (U) HMW-PE N2 - Two polyethylene types with ultra-high (UHMWPE) and high molecular weight (HMW-PE) used as neutron radiation shielding materials in casks for radioactive waste were irradiated with doses up to 600 kGy using a 60Co gammasource. Subsequently, thermal aging at 125∘C was applied for up to one year. Degradation effects in the materials were characterized using colorimetry, UV-Visspectroscopy, IR spectroscopy, and DSC. Both materials exhibited a yellowing upon irradiation.The discoloration of UHMW-PE disappeared again after thermal aging.Therefore, the yellowing is assumed to originate fromannealable color centers in the formof free radicals that are trapped in the crystalline regions of the polymer and recombine at elevated temperatures. For the antioxidantcontaining HMWPE, yellowing was observed after both irradiation and thermal aging. The color change was correlated mainly to decomposition products of the antioxidant in addition to trapped radicals as in UHMW-PE. Additionally, black spots appeared after thermal aging of HMW-PE. KW - Irradiation KW - UHMWPE KW - Colour center KW - Yellowness index PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-423992 DO - https://doi.org/10.1155/2017/1362491 SN - 1687-9422 VL - 2017 IS - Article ID 1362491 SP - 1 EP - 10 PB - Hindawi AN - OPUS4-42399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Evaluation of outdoor exposures by means of exposure response functions N2 - Outdoor exposure tests are a common tool to evaluate the weathering resistance of a polymeric material or component. However, they have only a limited validity, mainly due to the limited reproducibility of the weather as well as of the bad adaptability to other exposure sites. Typically, an outdoor exposure is characterized by the measured radiant exposure; sometimes averaged temperature data are added. These can be – separately – related to long-term annual means, to get an idea on the severity of the exposure. However, as for polymeric ageing, irradiance and temperature act simultaneously, such severity of an outdoor exposure could be better described by a computed property change of a similar material, which is calculated from the hourly irradiance and temperature values on the base of established exposure response functions. In this way, various outdoor exposures are evaluated. For several exposure sites, annual deviations of the ageing amount are related to annual mean values, to evaluate the weathering reproducibility at the exposure site. Additionally, correlations to relevant weather parameters are illuminated. Also some specific exposure conditions, such as tilt angle, are tested. Compared to the use of weathering reference materials, this procedure unfavourably depends on the availability of a suited control as well as on the quality of the established exposure response function. In contrast, it enables a later exposure evaluation, on the base of documented weather data, if for instance no reference material was exposed. T2 - 8th European Weathering Symposium CY - Vienna, Austria DA - 20.09.2017 KW - Weathering KW - Service life prediction KW - Photodegradation PY - 2017 SN - 978-3-9818507-1-0 VL - 18 SP - 127 EP - 135 PB - Thomas Würtz Grafik Design CY - Karlsruhe AN - OPUS4-42126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -