TY - JOUR A1 - Droste, Bernhard A1 - Gogolin, Bernd A1 - Völzke, Holger A1 - Quercetti, Thomas A1 - Günther, Burkhard T1 - Extended drop tests of DCI casks with artificial flaws demonstrating the existing safety margins PY - 1995 SN - 0957-476X VL - 6 IS - 2/3 SP - 177 EP - 182 PB - Nuclear Technology Publ. CY - Ashford, Kent AN - OPUS4-21732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Droste, Bernhard A1 - Völzke, Holger A1 - Wieser, Günter A1 - Qiao, Linan T1 - Safety Margins of Spent Fuel Transport and Storage Casks Considering Aircraft Crash Impacts PY - 2002 SN - 0957-476X VL - 13 IS - 3-4 SP - 313 EP - 316 PB - Nuclear Technology Publ. CY - Ashford, Kent AN - OPUS4-2697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Droste, Bernhard A1 - Zeisler, Peter A1 - Völzke, Holger A1 - Rödel, Roland T1 - Development and evaluation of containers for radioactive waste disposal PY - 1994 SN - 0957-476X VL - 5 IS - 1 SP - 27 EP - 32 PB - Nuclear Technology Publ. CY - Ashford, Kent AN - OPUS4-21735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Dynamic crushing characteristics of spruce wood under large deformations N2 - An extensive series of large deformation crushing tests with spruce wood specimens was conducted. Material orientation, lateral constraint and loading rate were varied. Regarding material orientation, a reduction in the softening effect and the general force level was observed with a higher fiber-load angle. A comparison with characteristics gained by application of Hankinson's formula showed discrepancies in compression strength and the beginning of the hardening effect. Lateral constraint of the specimens caused a multiaxial stress state in the specimens, which was quantified with the applied measuring method. Further, a higher force level compared to specimens without lateral constraint and significant hardening effect at large deformations resulted. Thus, the influence of a multiaxial stress state on the force level could be determined. An increase in the loading rate led to higher force levels at any displacement value and material orientation. KW - Crushing test KW - Dynamic crushing characteristics KW - Spruce wood KW - Lateral constraint KW - Multiaxial stress state KW - Hankinson's formula PY - 2013 U6 - https://doi.org/10.1007/s00226-012-0508-5 SN - 0043-7719 SN - 1432-5225 VL - 47 IS - 2 SP - 369 EP - 380 PB - Springer CY - Berlin AN - OPUS4-27743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Völzke, Holger A1 - Noack, Volker A1 - Weber, Wolfgang A1 - Wolff, Dietmar A1 - Rittscher, D. A1 - Schmidt, H. T1 - Construction of long term interim storage facility for nuclear reactor compartments of submarines: German support for utilisation of nuclear submarines in Russia KW - Interim storage facility KW - Nuclear reactor compartments of submarines KW - Building of the storage facility KW - Transportation of heavy compartments PY - 2008 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 19 IS - 2 SP - 117 EP - 121 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-17708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Völzke, Holger A1 - Probst, Ulrich A1 - Wolff, Dietmar T1 - Aging management for long-term interim storage casks N2 - The aging management system for the mechanical components of nuclear power plants (NPPs) must be established and used by the licensee in such a way that the quality of safety relevant components is guaranteed for the completely designed lifetime of the NPP. This demands an extensive plant life management with special emphases on the knowledge of the degradation in material properties. The basic safety concept in Germany observes this circumstance. Lifetime extension of the German NPPs is an aim of the current valid coalition agreement of the German government. Operational extension of interim storage facilities requires, in comparison to the aging management system for NPP, an aging management system adapted to the Special circumstances of spent fuel storage casks. Extension of interim storage periods for spent fuel casks beyond the designed lifetime requires, in comparison to the components of an NPP, an increasing knowledge of material degradation with potential impact on cask integrity, e.g. leak tightness. Dry interim storage in Germany has been approved for 40 years. After that time, according to the present strategy, a final repository should be available. However, until now, such a final facility still does not exist, and the German exploration and licensing process is heavily delayed. Currently, discussions are continuing regarding further exploration of the Gorleben salt mine. There is willingness to overcome this situation that is clearly described in the available coalition agreement of the federal government. Anyway, however, the prediction is viewed; a repository for heat generating radioactive waste in Germany will not be available in the near future and may not be available when first storage facilities and casks reach their 40 years of approved lifetime, which will occur in ~25 years starting from now. Therefore, the question must be asked: what has to be done with the existing storage casks in the interim facilities? May these casks be fit for continued use, with an extension of the storage period? One option is to have an aging management system, which creates enough information about the technical condition of safety relevant cask properties. This is the basis for safety evaluation for extended storage periods. In the present paper, possible aging mechanisms for high level waste storage casks are discussed, as well as the influence of the time dependent changes of the component properties. KW - Long term interim storage KW - Storage casks KW - Aging mechanisms KW - Degradation mechanisms KW - Metal seals KW - Larson-Miller parameter PY - 2011 U6 - https://doi.org/10.1179/1746510910Y.0000000013 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 1 SP - 46 EP - 53 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-23890 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grelle, Tobias A1 - Wolff, Dietmar A1 - Probst, Ulrich A1 - Jaunich, Matthias A1 - Völzke, Holger T1 - Component and material investigations on metal seals for high level radioactive waste containers N2 - Long-term investigations performed at BAM look to extend the state of knowledge on safety-related components of interim storage containers. Metal seals act as the primary sealing barrier in the bolted double lid closure system of the containers. The behaviour of metal seals has been investigated for ageing times up to 8.5 years and for various temperatures. The main cause for reduction in useable resilience overtime was due to creep deformation of the outer jacket of the seal. KW - Metal seal KW - Radioactive waste containers KW - Creep KW - Long-term behaviour PY - 2018 SN - 1745-2058 SP - 32 EP - 34 PB - Nuclear Institute CY - London AN - OPUS4-48206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - Goral, Milan A1 - Wolff, Dietmar A1 - Völzke, Holger ED - Krüssenberg, A. T1 - Overview of metal seal tests performed at BAM and implications for extended interim storage N2 - The investigation of the long-term performance of sealing systems employed in containers of radioactive waste and spent nuclear fuel is one research focus area for division 3.4 \Safety of Storage Containers" at the Bundesanstalt für Materialforschung und -prüfung. The behaviour of metallic seals, which are employed in interim storage casks for spent nuclear fuel and high active waste, over time is of high importance for ensuring safe enclosure. Therefore, investigations on these systems were started at BAM to get a general understanding of the relevant processes. Our investigations comprise investigations on different parameters which influence the seal Performance and the main part is focussed on the time and temperature dependent behaviour. Our aim is to understand the longterm behaviour of the sealing systems for evaluation of their performance during possible extended interim storage and subsequent transportation. In this contribution an overview of the performed tests and their respective results is given. A focus lies on a comparison between seals with large torus diameter in comparison to small diameters. T2 - Safety of Extended Dry Storage of Spent Nuclear Fuel SEDS2020: International online-workshop CY - Online meeting DA - 03.06.2020 KW - Metal seal KW - Seal performance KW - Long-term investigation KW - Ageing PY - 2020 U6 - https://doi.org/10.3139/124.200071 SN - 0932-3902 VL - 85 IS - 6 SP - 440 EP - 443 PB - Carl Hanser Verlag CY - München AN - OPUS4-51833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - von der Ehe, Kerstin A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Stark, Wolfgang T1 - Understanding low temperature properties of elastomer seals N2 - Elastomers are widely used as the main sealing materials for containers for low and intermediate level radioactive waste and as an additional component to metal seals in spent fuel and high active waste containers. The safe encapsulation of the radioactive container inventory has to be guaranteed according to regulation and appropriate guidelines for long term storage periods as well as for temperatures as low as -40°C during transport. Therefore, the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of elastomers are strongly temperature dependent. At low temperatures, this is caused by the rubber-glass transition (abbreviated: glass transition). During continuous cooling, the material changes from a rubber-like entropy elastic to a stiff energy elastic behaviour, which allows nearly no strain or retraction. Hence, rubbers are normally used above their glass transition, but the minimum working temperature limit is not defined precisely; this can cause problems during the above noted applications. Therefore, the lower operation temperature limit of elastomer seals must be determined in dependence of the material properties. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) are combined with standardised measurements to determine the compression set according to ISO 815. To reduce the test time of the standard tests, a faster technique than normally used was developed. Additionally, the breakdown temperature of the sealing function of complete O ring seals was measured in a component test set-up to compare it with the results of the other tests. The experimental set-up is capable of measuring the leakage rate at low temperatures by the pressure rise method. A fluorocarbon rubber (FKM) was selected for this investigation as it is often used for radioactive waste containers. The materials (seals and test sheets) were purchased from a commercial seal producer. KW - Sealing material KW - Elastomer KW - Compression set KW - Dynamic mechanical analysis KW - Low temperature behaviour PY - 2011 U6 - https://doi.org/10.1179/1746510911Y.0000000004 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 2 SP - 83 EP - 88 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-24015 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert T1 - Simulation of shock absorbing materials loaded by drop weights N2 - The numerical Simulation of transport and storage casks for radioactive waste in accidental scenarios requires adequate material models and input parameters for all relevant structural cask elements, the Impact foundation as well as possibly further components involved in the incident. They form the basis for reliable analysis of different loading situations allowing substituting, at least in parts, experimental investigations that are needed in safety Reports submitted for nuclear licensing procedures. Hereby, the efficiency of the energy absorbing components, such as cask Impact limiters or equivalent structures placed onto or into the foundation of storage buildings, determine to a large extend the performance and thus the design of the casks. The limiters, which are usually made of wood, polyurethane foam (PUF) or damping concrete, are subjected to Major plastic deformations, whose Distribution and magnitude strongly depend on loading speed, course and temperature. Consequently, it is necessary to establish a systematic data basis and implement this information in advanced numerical material formulations in Order to enable finite element simulations to account for all relevant factors. KW - Polyurethane foam KW - Spruce KW - Guided drop tests KW - Material models KW - Fem KW - Strain rate sensitivity KW - Temperature sensitivity PY - 2013 SN - 1431-5254 VL - 58 IS - 8/9 SP - 501 EP - 506 PB - Inforum CY - Berlin AN - OPUS4-29140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -