TY - CONF A1 - Sturm, Heinz T1 - Charakterisierung und Strukturierung von nm-Bereichen in Polymer-Werkstoffen - Ein AFM-ESEM-EBL-Hybridsystem T2 - BAM-Sonderheft 2003 "Polymere Verbundwerkstoffe zwischen Raumtemperatur und 4,2 K" ; 2. Symposium im DFG-Projekt: Eigenschaften von PTFE- und PEEK-Matrix-Werkstoffen bei tribologischer Beanspruchung CY - Berlin, Deutschland DA - 2003-02-27 PY - 2003 SP - 58 EP - 59 AN - OPUS4-2673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Crasselt, Claudia A1 - Schmidt, Wolfram A1 - Sturm, Heinz ED - M. Tyrer, ED - E. Ganjian, ED - West, A. T1 - Influence of rheology modifying admixtures on hydration of cementitious suspensions N2 - The presence of polycarboxylate ether (PCE) based superplasticizers (SPs) has an enormous influence on the early hydration of cement. The hydration is retarded and the timing of formation and the morphology of hydrates is affected. This short paper presents experimental results about the influence of delayed Addition time of PCE SPs on hydration of cement and tricalcium aluminate (C3A) pastes, investigated by isothermal heat flow calorimetry. For cement pastes the hydration is retarded with SP, whereby the high charge PCE has a stronger retarding effect than the low charge PCE. With delayed PCE addition the cement shows a less retarded setting than with simultaneous addition. The alteration caused by PCE is much more pronounced for C3A and gypsum mixes than for cement. If the SP is added simultaneous, the exothermic peak of C3A is retarded. However, with delayed addition of SP the hydration is shortened, the gypsum depletion is fastened and the exothermic peak occurs less retarded or even accelerated compared to simultaneous addition. It is obvious that for C3A pastes there is less retardation the later the Addition of SP. Furthermore, the PCE alter the hydration of C3A when added delayed and exhibit changes in kinetics and hydration rates. The rate of reaction in the second stage is lower, discernible in decreased slopes and broader peaks. Besides this, a distinct ramp in the C3A heat flow curves within the first stage of C3A hydration occurs for all pastes with delayed addition of SP, which suggests an accelerated ettringite formation. T2 - 38th Cement and Concrete Science Conference CY - Coventry, UK DA - 10.09.2018 KW - Cement hydration KW - Polycarboxylate ether KW - C3A hydration PY - 2018 SN - 978-1-84600-088-1 SP - 64 EP - 67 CY - Coventry, UK AN - OPUS4-45995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Marc Benjamin A1 - Solomun, Tihomir A1 - Sturm, Heinz T1 - Standard procedure for the irradiation of biomolecules with radiation of different linear energy transfer N2 - The damage caused by ionizing radiation to DNA and proteins is the reason to treat cancer by radiation therapy. A better understanding of the molecular processes and quantification of the different damaging mechanisms is the prerequisite to develop more efficient therapies. Hereby the understanding of the processes involved in the damage to DNA are of key interest due to its central role in reproduction and mutation. For radiation with low linear energy transfer (LET), most of the damage is caused by the secondary particles produced by scattering of the ionizing radiation with water. Thereby a multitude of species are produced, whereby especially kinetic low energy electrons, prehydrated electrons, OH-radicals and ions are of importance. With higher LET the relative amount of the direct damaging effects increases. This is especially important considering the increased usage of high LET nucleons in radiation therapy. Therefore, the quantification of the contribution to DNA damage of direct and indirect effects and the different secondary species is of high interest due to the increase of radio biological efficiency when applying high LET radiation. Here we present an approach to investigate the relative contributions to DNA strand break yield for radiation of different LET within a single electron microscope in combination with electron scattering simulations. T2 - XI International Radiation Protection Association Conference 2018 America CY - Havanna, Cuba DA - 16.04.2018 KW - Dosimetry KW - Linear energy transfer KW - Radiation damage KW - LET KW - Electron irradiation KW - Low energy electrons KW - Hydroxyl radicals KW - DEA KW - DET KW - Microdosimetry KW - Geant4 KW - Electron irradiation of DNA KW - DNA PY - 2018 VL - 2018 SP - 1 EP - 5 AN - OPUS4-44848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Sturm, Heinz A1 - Schmidt, Dieter A1 - Kautek, Wolfgang T1 - Chemical, morphological and accumulation phenomena in ultrashort-pulse laser ablation of TiN in air N2 - Ultrashort-pulse laser ablation (F=130 fs, 5=800 nm, repetition rate 2-20 Hz) of titanium nitride was investigated for laser fluences between 0.3 and 4.5 J/cm2 using the direct focusing technique in air. The influence of the laser pulse number and the peak fluence was investigated by means of several surface analytical techniques (optical microscopy, dynamic friction atomic force microscopy, scanning Auger electron microscopy and small-spot electron spectroscopy for chemical analysis). The correlation of the results about optical, physical and chemical properties of the irradiated areas allows us to propose a simple oxidation model, which explains different observed phenomena associated with surface damage such as mound formation and crater widening and clarifies the incubation behavior reported earlier for this material. PY - 2000 DO - https://doi.org/10.1007/s003390000585 SN - 0947-8396 VL - 71 IS - 6 SP - 657 EP - 665 PB - Springer CY - Berlin AN - OPUS4-1067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cappella, Brunero A1 - Geuss, Markus A1 - Sturm, Heinz A1 - Heyde, M. A1 - Rademann, K. A1 - Spangenberg, T. A1 - Niehus, H. T1 - Dynamic plowing nanolithography on polymethylmethacrylate using an atomic force microscope N2 - We present dynamic plowing nanolithography on polymethylmethacrylate films, performed with a scan-linearized atomic force microscope able to scan up to 250 μm with high resolution. Modifications of the surface are obtained by plastically indenting the film surface with a vibrating tip. By changing the oscillation amplitude of the cantilever, i.e., the indentation depth, surfaces can be either imaged or modified. A program devoted to the control of the scanning process is also presented. The software basically converts the gray scale of pixel images into voltages used to control the dither piezo driving cantilever oscillations. The advantages of our experimental setup and the dependence of lithography efficiency on scanning parameters are discussed. Some insights into the process of surface modifications are presented. KW - Nanolithography PY - 2001 UR - http://rsi.aip.org/ DO - https://doi.org/10.1063/1.1326053 SN - 0034-6748 SN - 1089-7623 VL - 72 SP - 136 EP - 141 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schönhals, Andreas A1 - Frunza, S. A1 - Frunza, L. A1 - Goering, Harald A1 - Sturm, Heinz T1 - On the dynamics of surface layer in octylcyanobiphenyl-aerosil systems N2 - A broadband dielectric study of the dispersions of silica spheres (Aerosil 380) in octylcyanobiphenyl (8CB) with densities between 0.083 and 10 g of silica per 1 cm3 of liquid crystal (LC) is reported. High values of silica densities were achieved for the first time to observe the behaviour of the LC monolayer on the surface of the silica particles. The relaxation characteristic of the bulk LC is noticed especially for the samples with low silica densities. Additionally, a slow relaxation was detected, even at temperatures for which the bulk LC is in the crystalline state. It was assigned to the surface layer of LC molecules. Remarkably, the temperature dependence of the relaxation rates for this slow process shows a behaviour typical for glass-forming liquids. PY - 2001 DO - https://doi.org/10.1209/epl/i2001-00591-8 SN - 0302-072X SN - 0295-5075 SN - 1286-4854 VL - 56 IS - 6 SP - 801 EP - 807 PB - EDP Science CY - Les-Ulis Cedexa, France AN - OPUS4-1572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Munz, Martin A1 - Sturm, Heinz A1 - Schulz, Eckhard T1 - Interphase Characterization via the Stiffness Contrast of a Scanning Force Microscope in Displacement Modulation Mode N2 - The physical properties as well as the thickness of the interphase between polymer and reinforcing phase are generally expected to show a strong influence on the macroscopic mechanical properties of composite materials. In this study the scanning force microscope (SFM) has been applied for detecting stiffness gradients near the interface between copper and epoxide. In displacement modulation mode the load exerted by the tip is modulated sinusoidally by vibrating the normal position of the cantilever or the sample. The corresponding amplitude of dynamic cantilever bending is related to local surface stiffness. Thus, using the SFM, the local mechanical properties of the surface under investigation can be probed. When scanning the tip across the reinforcement/polymer interface, the polymeric interphasial zone can be identified with the observed stiffness gradient. For a commercial epoxide based on diglycidyl ether of bisphenol A (DGEBA) cured with an amine-containing hardener, a stiffness gradient was detected that could be fitted by a Gaussian profile typical for diffusional processes. The width of the stiffness gradient was 280 nm. The observation is discussed in terms of interface-induced segregation processes between resin and hardener, as well as heat conduction mechanisms that can occur during the exothermic curing reaction. Both mechanisms are diffusional in nature and, via the local network structure, are expected to show some influence on the local stiffness of the cured epoxy. Copyright © 2000 John Wiley & Sons, Ltd. T2 - ECASIA 99 CY - Sevilla, Spain DA - 1999-10-04 KW - Scanning Force Microscopy KW - Surface properties KW - Nanomechanics KW - Interface/Interphase KW - Polymer-matrix composites (PMCs) KW - Adherends PY - 2000 DO - https://doi.org/10.1002/1096-9918(200008)30:1<410::AID-SIA846>3.0.CO;2-G SN - 0142-2421 SN - 1096-9918 VL - 30 IS - 1 SP - 410 EP - 414 PB - Wiley CY - Chichester AN - OPUS4-873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Munz, Martin A1 - Sturm, Heinz A1 - Schulz, Eckhard A1 - Hinrichsen, G. T1 - The scanning force microscope as a tool for the detection of local mechanical properties within the interphase of fibre reinforced polymers N2 - Scanning force microscopy (SFM) has been used to assess the local mechanical properties of fibre-reinforced polymers. Using a sinusoidal displacement modulation (DM) and lock-in technique the method allows to characterize local viscoelastic properties with a high lateral resolution. The simultaneous measurement of the local electrical conductivity is proposed which facilitates the interpretation of the mechanical data. The investigation of cross-sections perpendicular to the axis of carbon fibres embedded in PPS delivers some information about the change in local stiffness within the interfacial region. As a first approach, assuming a single-exponential decrease in local stiffness along a radial line from fibre to polymer we find characteristic decay lengths which are distributed in a range between 20 and 80nm. Further, a modified DM-mode is proposed which is expected to provide a contrast enhancement of the signal which is related to local stiffness. This can be achieved by installing an additional feedback loop which keeps constant the amplitude of dynamic indentation (CDI-mode). KW - Polymer-matrix composites (PMC´s) KW - Interface/interphase KW - SFM/AFM KW - Surface properties KW - Nondestructive testing PY - 1998 DO - https://doi.org/10.1016/S1359-835X(98)00077-3 SN - 1359-835X VL - 29 SP - 1251 EP - 1259 PB - Elsevier CY - Oxford AN - OPUS4-1294 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sturm, Heinz A1 - Cappella, Brunero A1 - Heyde, M. A1 - Ritter, C. A1 - Rademann, K. T1 - Dislocation of antimony clusters on graphite by means of dynamic plowing nanolithography N2 - Antimony clusters of different shapes and dimensions have been obtained by evaporating antimony on graphite. The dependence of the shape and dimensions of the particles on the evaporation parameters (effective layer thickness, temperature, pressure) is discussed. A characterisation of the different structures is presented. In particular, the decoration of graphite steps is discussed. Clusters have been dislocated by means of dynamic plowing nanolithography, both in vector and in image pattern mode. The dependence of the energy needed to dislocate a cluster on its dimensions and position is discussed. KW - Antimony clusters KW - Nanolithography PY - 2001 DO - https://doi.org/10.1016/S0039-6028(00)01113-4 SN - 0039-6028 VL - 476 IS - 1-2 SP - 54 EP - 62 PB - Elsevier CY - Amsterdam AN - OPUS4-875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cappella, Brunero A1 - Sturm, Heinz T1 - Dynamic Plowing Lithography of Single Holes on Polymethylmethacrylate Using an Atomic Force Microscope N2 - Dynamic Plowing Lithography is employed to carve holes in a PMMA surface by indenting the sample during Tapping Mode imaging. The dependence of the dimensions of the holes on the tip shape, on the modulation voltage amplitude, and on the number of contacts between the tip and sample is studied. The results give some insights in the physico-chemical mechanisms accompanying such rapid modifications. Two-dimensional arrays of holes have also been carved, in order to study the result of the superposition of single holes. PY - 2001 SN - 0044-376x VL - 10 Suppl. 1 SP - 8 EP - 15 PB - Hirzel CY - Stuttgart, Germany AN - OPUS4-1633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -