TY - THES A1 - Stoppel, Markus T1 - Differenzpotentialfeldmessung in der automatisierten Prüfung von Stahlbetonbauteilen N2 - Die Potentialfeldmessung ist eines der wichtigsten zerstörungsfreien Prüfverfahren für die Zustandsbewertung von Stahlbetonbauteilen. Mit dieser Methode kann eine ortsabhängige Wahrscheinlichkeit für aktive, chloridinduzierte Bewehrungskorrosion bestimmt werden. Bei der konventionellen Anwendung wird über ein langes Schleppkabel eine Verbindung zwischen einem Messgerät und der Bewehrung hergestellt. Eine Interpretation der Messergebnisse wird anhand der absoluten Potentialwerte durchgeführt. Die Zuordnung zu aktiven oder passiven Zustanden der Bewehrung ist dabei nicht eindeutig. Eine zuverlässigere Methode der Bewertung des Korrosionspotentials ist jedoch die Bestimmung der Gradienten der Messspannungen. Das vorrangige Ziel dieser Arbeit ist es, die Potentialfeldmessung zu einem vollkommen zerstörungsfreien Differenzpotentialfeldmessverfahren (DP-Messung) weiter zu entwickeln, mit dem die Potentialgradienten direkt gemessen werden und bei dem auf die permanente Ankoppelung an die Bewehrung verzichtet werden kann. Die Arbeit fasst die Entwicklungsschritte zusammen und definiert die Bewertungskriterien für die DP-Messung, die die Qualität der Interpretation verbessern. Anhand der neu definierten Gradientenbreite wird aufgezeigt, wie die Detektionswahrscheinlichkeit für korrosionsaktive Bereiche erhöht wird. Es wird gezeigt, wie die automatisierte Kombination des Verfahrens mit großflächigen Messungen des Feuchtegehalts und der Betondeckung zu einer zuverlässigeren Zustandsbewertung führt. N2 - The half-cell potential test is one of the most important non-destructive testing techniques used for condition evaluation of reinforced concrete structures. This method gives the probability of chloride-induced corrosion in steel reinforcing rebars. The conventional approach involves exposing a rebar and using a long wire to connect the measurement device to the rebar. An interpretation of the measurement results is carried out based on the absolute potential values. The assignment to active or passive states of the reinforcement is not unique. However, it has been recently found that the gradient of the measured potentials provides a more reliable assessment of the corrosion potential of reinforcements. The primary objective of this work was to enhance the potential mapping technique by developing a difference potential mapping (DP-method), which can directly measure the potential gradients. Taking this new approach, a permanent connection to the rebar would be no longer required. The work summarizes the development details and the assessment criteria for the DPmethod, which improves the quality of interpretation. The newly defined gradient-width Shows how the detection probability of corrosion-active areas is improved. Moreover, it has been shown that combining the potential measurements with automated large-scale measuring the concrete cover and moisture content lead to a more reliable condition assessment. T3 - BAM Dissertationsreihe - 75 KW - Detektion KW - Zerstörungsfreie Prüfung KW - Stahlbeton KW - Elektrochemische Korrosion KW - Potentialfeld PY - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-833 SN - 978-3-9814281-5-5 SN - 1613-4249 VL - 75 SP - 1 EP - 183 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-83 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Boller, C. T1 - Automated multi-sensor systems in civil engineering for condition assessment of concrete structures T2 - Concrete Solutions 2011, 4th International Conference on Concrete Repair CY - Dresden, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24680 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Kurz, J.H. A1 - Taffe, Alexander A1 - Boller, C. ED - Chang, F.-K. T1 - Proactive condition assessment in civil engineering using automated multi-sensor systems N2 - Infrastructure is subject to continuous ageing. This has given life cycle management of infrastructure an increasing role. Reliable inspection and monitoring tools are therefore an increasing demand. A combination of different non-destructive test methods is often necessary to receive reliable results for material characterization, flaw detection and the determination of component specific geometry parameters. Regarding concrete structures thickness measurements are combined with flaw detection and additional information about reinforcement and tendon ducts is required. Therefore, a multi-sensor measurement approach is necessary with a high degree of automation. Otherwise a time consuming succession of manual measurements has to be performed which would prevent practical applications. A modular control and data acquisition approach is described and the application of two different automated measurement devices is shown. The BetoScan system consists of a self-navigating mobile robot. The system is especially designed for the investigation of reinforced concrete floors exposed to de-icing salts. The data acquisition of the OSSCAR system a multi-sensor scanner is similar to the robot approach. These different applications are based on a similar kernel allowing the modular use of different contact and noncontact sensors. The described general concept of multi-sensor data acquisition and data analysis presented here is not limited to the field of civil engineering applications. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Multi sensor KW - Data acquisition KW - Assessment of concrete structures KW - Scanner KW - NDT PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 2359 EP - 2366 PB - DEStech Publications, Inc. AN - OPUS4-24692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Kind, Thomas A1 - Stoppel, Markus A1 - Kurz, J. H. T1 - OSSCAR-Bauwerkscanner: Automatisierte Datenaufnahme von Radar, Ultraschall und Wirbelstrom an Spannbetonbauteilen mit bildgebender Darstellung der inneren Konstruktion N2 - Bereits seit vielen Jahren stehen Anwendern der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) zuverlässige Geräte für Radar-, Wirbelstrom- und Ultraschallmessungen an Betonbauteilen zur Verfügung. Doch erst die Kombination dieser drei Verfahren an einer Messfläche erlaubt den maximalen Informationsgewinn über die innere Konstruktion von Stahlbeton- und Spannbetonbauteilen. Mit dem OSSCAR-Bauwerkscanner wurden diese drei Verfahren erstmals zur kombinierten und automatisierten Datenaufnahme an einem Scannerrahmen und unter einer Software vereint. Die Ergebnisse werden bildgebend in frei wählbaren Schnitten dargestellt, was eine Rekonstruktion von Bauteilen erlaubt, für die keine Planunterlagen vorliegen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Bauwerkscanner KW - Brückenprüfung KW - Ultraschall KW - Radar KW - Wirbelstrom KW - Kombination PY - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-253767 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.3.B.1) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zoëga, Andreas A1 - Stoppel, Markus A1 - Feldmann, Rüdiger T1 - Automatisierte Multisensorsysteme zur Zustandsbewertung T2 - Fachtagung Bauwerksdiagnose 2012 - Praktische Anwendungen zerstörungsfreier Prüfungen und Zukunftsaufgaben CY - Berlin, Deutschland DA - 2012-02-23 KW - Bauwesen KW - Zerstörungsfreie Prüfung KW - Automatisierung KW - Multisensorsysteme / BetoScan / ZFP-Scanner PY - 2012 SN - 978-3-940283-40-5 IS - DGZfP-BB 134 (Vortrag 07) SP - 1 EP - 9 CY - Berlin AN - OPUS4-25548 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus T1 - BetoScan "Selbstfahrendes Scannersystem für Betonflächendiagnosen" T2 - Bauwerksdiagnose 2008 CY - Berlin, Germany DA - 2008-02-21 PY - 2008 AN - OPUS4-16678 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus T1 - BetoScan "Selbstfahrendes Scannersystem für Betonflächendiagnosen" T2 - Technische Akademie Esslingen, 3. Kolloquium "Verkehrsbauten" CY - Ostfildern, Germany DA - 2008-01-29 PY - 2008 AN - OPUS4-16518 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Stoppel, Markus A1 - Mielentz, Frank A1 - Wiggenhauser, Herbert T1 - Automatisierung in der zerstörungsfreien Prüfung KW - Automatisierte ZfPBau-Verfahren KW - Radar KW - Ultraschallecho KW - Impact-Echo KW - Spannbetonbrücken PY - 2006 SN - 978-3-433-01833-0 SN - 0342-7617 VL - 96-1 IS - Kap. V / Abschnitt 10 SP - 562 EP - 567 PB - Ernst CY - Berlin AN - OPUS4-14435 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stoppel, Markus ED - Susanne Gieler-Breßmer, T1 - BetoScan - Selbstfahrendes Scannersystem für Betonflächendiagnosen T2 - 3. Kolloquium Verkehrsbauten - Schwerpunkt Parkhäuser/Brücken CY - Ostfildern, Deutschland DA - 2008-01-29 KW - BetoScan KW - Betonflächendiagnose KW - Scanner KW - ZfP im Bauwesen PY - 2008 SN - 3-924813-72-8 IS - Tagungshandbuch 2008 SP - 1 EP - 3 AN - OPUS4-18660 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Stoppel, Markus A1 - Taffe, Alexander A1 - Kurz, J.H. A1 - Reichling, K. ED - Gieler-Breßmer, S. T1 - Zustandsermittlung und Schadensdiagnose für Parkhäuser mit automatisierten zerstörungsfreien Prüfverfahren T2 - 4. Kolloquium Verkehrsbauten - Schwerpunkt Parkhäuser CY - Ostfildern, Deutschland DA - 2010-02-02 KW - BetoScan KW - Betonflächendiagnose KW - Scanner KW - ZfP im Bauwesen PY - 2010 SN - 3-924813-82-5 IS - Kap. 11.1 SP - 1 EP - 9 CY - Ostfildern AN - OPUS4-22722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -