TY - JOUR A1 - Abdelkhalik, A. A1 - Askar, Enis A1 - Markus, D. A1 - Stolz, T. A1 - Brandes, E. A1 - Zakel, S. T1 - Explosion regions of 1,3-dioxolane/nitrous oxide and 1,3-dioxolane/air with different inert gases - Experimental data and numerical modelling N2 - In this study, experimental determination and modelling investigations for the explosion regions of 1,3-dioxolane/inert gas/N2O and 1,3-dioxolane/inert gas/air mixtures were carried out and compared. The experimental measurements were carried out at 338 K and atmospheric pressure according to EN1839 method T using the inert gases N2, CO2, He and Ar. The results showed that the ratio of the lower explosion limit in N2O (LELN2O) to the lower explosion limit in air (LELair) is 0.52 and the ratio of the maximum oxygen content in air (MOCair) to the limiting oxidizer fraction in nitrous oxide (LOFN2O) is 0.36 ± 0.02 independent of the inert gas. When comparing the inert gas amount at the apex based on the pure oxidizing component, which is O2 in case of air, N2O-containing mixtures need less inert gas to reach the limiting oxidizer quantity whereas the efficiency of inert gases is in the same order. The coefficients of nitrogen equivalency however were found to differ to some extent. The explosion regions of 1,3-dioxolane/inert gas/oxidizer mixtures were modelled using the calculated adiabatic flame temperature profile (CAFTP) method as well as corrected adiabatic flame temperatures. The results indicate good agreement with experimental data for CO2, N2 and Ar- containing mixtures. The noticeable deviations that occur when He is the inert gas are due to the lacking transport data of that mixture. KW - Explosion limits KW - Flammability KW - CAFTP KW - Adiabatic Flame Temperatures PY - 2021 U6 - https://doi.org/10.1016/j.jlp.2021.104496 SN - 0950-4230 VL - 71 SP - 4496 PB - Elsevier Ltd AN - OPUS4-52849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Lüth, Peter A1 - Brandes, E. A1 - Stolz, T. T1 - Interlaboratory test 2012-2013 on the method EN 14522:2005 "Determination of the auto ignition temperature of gases and vapours" / IEC 60079-20-1, part 7 "Method of test for auto-ignition temperature" N2 - For the classification, safe handling and use of chemicals, special standardised test methods have been developed and are used worldwide. Safety experts must be able to fully rely on the precise execution of the respective laboratory tests and assessments. In this context interlaboratory tests (round robin tests, interlaboratory comparisons / intercomparisons) are a crucial element of both the further development and improvement of the methods and of a laboratory's quality system. Participation in interlaboratory tests is explicitly recommended by the standard ISO/IEC 17025. This document reports on the results of the interlaboratory test 2012-2013 on the test method EN 14522:2005 “Determination of the auto ignition temperature of gases and vapours“ / IEC 60079-201, part 7 ”Method of test for auto-ignition temperature”. The auto ignition temperature is an important safety characteristic for explosion protection and prevention. It is the basis for classifying substances and explosion protected equipment into temperature classes. Because safety characteristic data are not a pure substance constant but a figure which denotes a special property of the substance, the determination methods are standardised. Currently EN 14522 and IEC 60079-20-1, part 7 are under revision with the aim to combine both to a standard accepted worldwide. An important part of the standard is the laboratory’s verification of their apparatus and procedure. To base this forthcoming standard on reliable and up-to-date verification data an interlaboratory test appears as the method of choice. The verification data given in the recent issues of the standards are based on comparison measurements which date back to a long time ago and did not include automated apparatuses. KW - Ringversuch KW - Auto ignition temperature KW - Zündtemperatur KW - Liquids KW - Flüssigkeiten PY - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-306867 SN - 978-3-9816380-0-4 SP - 1 EP - 89 PB - Bundesanstalt für Materialforschung und -prüfung (BAM), Physikalisch-Technische Bundesanstalt (PTB) CY - Berlin, Braunschweig ET - Final Report AN - OPUS4-30686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abdelkhalik, A. A1 - Askar, Enis A1 - Markus, D. A1 - Brandes, E. A1 - El-Sayed, I. A1 - Hassan, M. A1 - Nour, M. A1 - Stolz, T. T1 - Explosion regions of propane, isopropanol, acetone, and methyl acetate/inert gas/air mixtures N2 - The explosion regions for propane, isopropanol, acetone, and methyl acetate with air in the presence of nitrogen, argon, helium, and carbon dioxide were determined experimentally according to EN 14756/EN1839, method T. Except for propane, all the measurements were executed at 323 K and 1 bar. Propane experiments were carried out at 293 K and 1 bar. The results show that for the same type of inert gas, propane, isopropanol, and acetone have great closeness concerning the concentration of the inert gas at the apex of the explosion envelope in a ternary diagram with air as oxidizer. This leads to consistency in the limiting oxygen concentration (LOC) and minimum required amount of inert gas (MAI) values. Concerning methyl acetate, the apex was always reached at higher percentages of inert gases compared with the other fuels. This can be attributed to the presence of two oxygen atoms inside the chemical structure. Calculation of the explosion regions was carried out based on calculated adiabatic flame temperature (CAFT) method. The flame temperatures for the experimentally determined fuel/air/N2 mixtures were calculated. Then, these temperatures were used to predict the explosion limits of similar mixtures with other inert gases than nitrogen. The modeling results show reasonable agreement with the experimental results. KW - Flammability limits KW - Model of constant adiabatic flame temperatures (CAFT) KW - Inertisation KW - Explosion protection PY - 2016 U6 - https://doi.org/10.1016/j.jlp.2016.04.001 SN - 0950-4230 VL - 2016/43 SP - 669 EP - 675 PB - Elsevier Ltd. CY - Oxford, UK AN - OPUS4-37996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abdelkhalik, A. A1 - Askar, Enis A1 - Markus, D. A1 - Brandes, E. A1 - Stolz, T. T1 - Explosion regions of acetone and alcohol/inert gas/air mixtures at high temperatures and atmospheric pressure N2 - The explosion regions of 1-propanol, 2-propanol, acetone and 1-butanol in air were measured in the presence of CO2, He, N2 and Ar in accordance with EN1839 method T at high temperatures and at atmospheric pressure. The experimental results show that 1-propanol, 2-propanol and acetone have very similar lower explosion limits (LELs). 1-Butanol shows a slightly wider explosion area near the LEL line. In addition, the explosion regions of all combustible/inert gas/air mixtures were calculated with the method of constant adiabatic flame temperature profiles (CAFTP), using the flame temperature profile along the explosion region boundary curve of each combustible/N2/air mixture as a reference to determine the explosion regions of combustible/inert gas/air mixtures with inert gases other than N2 at different initial temperatures. To calculate the explosion regions for systems containing He, the calculation method was modified to include the very different physical transport properties of He. Moreover, the procedure for calculating the apexes in the ternary explosion diagrams was modified. The calculation results show good agreement with the experimental results. KW - Explosion limits KW - Elevated temperatures KW - Alcohols KW - CAFTP KW - Acetone PY - 2019 U6 - https://doi.org/10.1016/j.jlp.2019.103958 SN - 0950-4230 VL - 62 SP - 103958, 1 EP - 8 PB - Elsevier AN - OPUS4-49030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Askar, Enis A1 - Aksam, A. A1 - Brandes, E. A1 - Markus, D. A1 - Stolz, T. T1 - Berechnung der Explosionsbereiche von Alkoholen, Ketonen und halogenierten Kohlenwasserstoffen im Gemisch mit Inertgasen N2 - Die Explosionsbereiche für Dreistoffsysteme aus Brennstoff Inertgas und Luft wurden nach dem Modell der konstanten adiabatischen Flammentemperaturprofile berechnet. Für die Parametrisierung des halbempirischen Modells muss der Explosionsbereich für ein bestimmtes Dreistoffsystem aus Brennstoff, Inertgas und Luft bekannt sein. Dann lassen sich Explosionsbereiche desselben Brennstoffs mit einem beliebigen Inertgas und bei einer beliebigen Temperatur berechnen. Ergänzend zu früheren Arbeiten, in denen die Explosionsbereiche für Brenngase aus der homologen Reihe der Alkane und Alkene berechnet worden sind, wurden nun die Berechnungen für 1-Propanol, Aceton und Difluormethan durchgeführt. Als Inertgase wurden neben Stickstoff und Kohlendioxid auch die Edelgase Argon und Helium berücksichtigt. Für die Berechnung der Explosionsbereiche in Systemen mit Helium, ist das Modell erweitert worden, so dass auch die Transporteigenschaften (d.h. Wärmeleitfähigkeit, Diffusionskoeffizient) der Komponenten berücksichtigt werden. Weiterhin ist eine Möglichkeit zur praxisnahen Berechnung der Spitze des Explosionsbereichs implementiert worden. Die Ergebnisse zeigen insgesamt, dass die Berechnung der Explosionsbereiche für Alkohole, Ketone und halogenierte Kohlenwasserstoffe mit ähnlicher Genauigkeit wie für Alkane und Alkene möglich ist. Die vorgenommenen Modifikationen sind geeignet, um auch eine Berechnung für Gasgemische mit Helium durchzuführen, dessen starke inertisierende Wirkung im Vergleich zu den Inertgasen Argon oder Stickstoff vor allem auf den stark unterschiedlichen Transporteigenschaften beruht. KW - Explosionsgrenzen KW - Inertisierung KW - Modell der konstanten Flammentemperaturen KW - Explosionsschutz PY - 2020 U6 - https://doi.org/10.7795/310.20200199 SN - 0030-834X VL - 130 IS - 1 SP - 25 EP - 29 AN - OPUS4-50945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brandes, E. A1 - Stolz, T. A1 - Adebahr-Lindner, Yvonne A1 - Krischok, Frank T1 - Sicherheitstechnische Kenngrößen für die Tankschifffahrt auf Binnenwasserstraßen T1 - Safety characteristic data for the tanker shipping on inland waterways N2 - Im Europäisches Übereinkommen über die Internationale Beförderung gefährlicher Güter auf Binnenwasserstraßen ist festgelegt, welche gefährlichen Güter unter welchen Bedingungen auf europäischen Binnenwasserstraßen befördert werden dürfen. Tabelle C ‚Verzeichnis der zur Beförderung in Tankschiffen zugelassenen gefährlichen Stoffe in numerischer Reihenfolge’ (ADN 3.2.2) listet für die Stoffe, Gemische und Lösungen, deren Beförderung in Tankschiffen zugelassen ist, die anzuwendenden besonderen Vorschriften entweder in vollständiger Information oder in kodierter Form auf. In dieser Tabelle C werden für die einzelnen Stoffe vor allem die zu verwendenden Tankschifftypen, deren Ausrüstung sowie Anforderungen hinsichtlich des Explosionsschutzes, des Schutzes der aquatischen Umwelt und des Schutzes der Menschen vor längerfristigen gesundheitlichen Schäden festgelegt. Bei dem Datenmaterial handelt es sich um durch PTB und BAM bewertete, experimentell oder rechnerisch ermittelte sicherheitstechnische Kenngrößen sowie um Angaben zu den aquatoxischen Eigenschaften und zu den längerfristigen gesundheitlichen Wirkungen auf den Menschen. Die Angaben zum Wasserverunreinigungspotential und die Zuordnungen zu den aquatoxischen Gefahren N1, N2, N3 wurden im Rahmen der Arbeiten der Zentralkommission für die Rheinschifffahrt (ZKR) zu Tabelle C vom Umweltbundesamt (UBA, J. Seelisch) zusammengestellt und bewertet. Die Angaben zu den längerfristigen gesundheitlichen Wirkungen auf den Menschen entsprechen den harmonisierten Einstufungen der EU. KW - Sicherheitstechnische Kenngrößen KW - Ladetankausrüstung KW - Tankschifftyp KW - ADN Tabelle C KW - Binnenwasserstraßen KW - Beförderung gefährlicher Güter KW - Europäisches Übereinkommen PY - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-495985 SP - 1 EP - 261 AN - OPUS4-49598 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis A1 - Aksam, A. A1 - Brandes, E. A1 - Markus, D. A1 - Stolz, T. T1 - Berechnung der Explosionsbereiche von Alkoholen, Ketonen und halogenierten Kohlenwasserstoffen im Gemisch mit Inertgasen N2 - Die Explosionsbereiche für Dreistoffsysteme aus Brennstoff, Inertgas und Luft wurden nach dem Modell der konstanten adiabatischen Flammentemperaturprofile berechnet. Für die Parametrisierung des halbempirischen Modells muss der Explosionsbereich für ein bestimmtes Dreistoffsystem aus Brennstoff, Inertgas und Luft bekannt sein. Dann lassen sich Explosionsbereiche desselben Brennstoffs mit einem beliebigen Inertgas und bei einer beliebigen Temperatur berechnen. Ergänzend zu früheren Arbeiten, in denen die Explosionsbereiche für Brenngase aus der homologen Reihe der Alkane und Alkene berechnet worden sind, wurden nun die Berechnungen für 1-Propanol, Aceton und Difluormethan durchgeführt. Als Inertgase wurden neben Stickstoff und Kohlendioxid auch die Edelgase Argon und Helium berücksichtigt. Für die Berechnung der Explosionsbereiche in Systemen mit Helium, ist das Modell erweitert worden, so dass auch die Transporteigenschaften (d.h. Wärmeleitfähigkeit, Diffusionskoeffizient) der Komponenten berücksichtigt werden. Weiterhin ist eine Möglichkeit zur praxisnahen Berechnung der Spitze des Explosionsbereichs implementiert worden. Die Ergebnisse zeigen insgesamt, dass die Berechnung der Explosionsbereiche für Alkohole, Ketone und halogenierte Kohlenwasserstoffe mit ähnlicher Genauigkeit wie für Alkane und Alkene möglich ist. Die vorgenommenen Modifikationen sind geeignet, um auch eine Berechnung für Gasgemische mit Helium durchzuführen, dessen starke inertisierende Wirkung im Vergleich zu den Inertgasen Argon oder Stickstoff vor allem auf den stark unterschiedlichen Transporteigenschaften beruht. Für die Analyse der physikalischen Vorgänge, die zur Zündung führen, ist eine spezielle Kontaktvorrichtung entwickelt worden. Damit können die Entladungen > 200 µm Länge und mit einer Dauer von > 500 µs an einer bestimmbaren Position erzeugt und untersucht werden. Für die Entladungen an der Zündgrenze bei niedrigen Spannungs- und Stromwerten (max. 30 V, 30 bis 100 mA Konstantstrombegrenzung) sind die Bedingung für die Erzeugung ermittelt worden. Das sind die Rauheit auf der Kontaktoberfläche, die langsame Kontaktöffnungsbewegung und eine geeignet regelnde Spannungsquelle mit Konstantstrombegrenzung. Damit sind für diese Entladungen an der Zündgrenze die Strom-Spannungs-Kennlinie, das Spektrum mit dominierenden Linien von Cadmium-Metalldampf sowie die Temperaturverläufe ermittelt worden. T2 - 15. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Brunswick, Germany DA - 21.05.2019 KW - Explosionsgrenzen KW - Inertisierung KW - Modell der konstanten Flammentemperaturen KW - Explosionsschutz PY - 2019 U6 - https://doi.org/10.7795/210.20190521J SP - 1 EP - 9 AN - OPUS4-48947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Brandes, E. A1 - Colson, B. A1 - Frost, K. A1 - Lüth, Peter A1 - Simon, K. A1 - Stolz, T. A1 - Uhlig, S. T1 - Evaluation of the interlaboratory test 2015 – 2016 on the method UN Test L.2 “Sustained combustibility test” / EN ISO 9038:2013 “Determination of sustained combustibility of liquids" N2 - The test methods UN Test L.2 / EN ISO 9038:2013 DIN EN 15188:2007 are applied to characterize the sustained combustibility of liquids i.e. the behaviour of a material under specified test conditions, whereby its vapour can be ignited by an ignition source and sufficient flammable vapour is produced to continue burning for at least 15 s after the source of ignition has been removed. The aims of this interlaboratory test (IT) are the verification and/or the improvement (if necessary) of the verification data (reference material) in Annex B of EN ISO 9038:2013, the assessment of influencing (disturbing) factors (laboratory specific factors, which possibly may have an influence on the test result) and the assessment of the performance of the participating laboratories. It could be demonstrated that the reference materials n-Dodecane, n-Decane and n-Undecane as mentioned in the standard are suitable and the verification shall continue to be valid. Sustained combustibility tests are influenced by several factors like the presence of a draught shield, the experience of the laboratory assistant, verification of the apparatus, calibration of the metering device. Based on the interlaboratory test, the gained experience and the actual results, well-founded measures / actions can be recommended to improve execution of the method. The IT was organized by PTB, BAM and QuoData GmbH in the framework of the co-operation project CEQAT-DGHS Centre for Quality Assurance for Testing of Dangerous Goods and Hazardous Substances. KW - Dangerous goods KW - Hazardous substances KW - Test method KW - Quality assurance KW - Interlaboratory comparison KW - Round robin test KW - Validation KW - Sustained combustibility KW - Reference material KW - Gefahrgut KW - Gefahrstoff KW - Prüfmethode KW - Qualitätssicherung KW - Ringversuch KW - Validierung KW - Selbstunterhaltende Verbrennung KW - Referenzmaterial PY - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-410270 SN - 978-3-9818270-3-3 SP - 1 EP - 103 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-41027 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -