TY - JOUR A1 - Meine, Kerstin A1 - Kloß, K. A1 - Schneider, Thomas A1 - Spaltmann, Dirk T1 - The influence of surface roughness on the adhesion force N2 - Adhesion measurements are presented which were carried out with an atomic force microscope between polymer balls attached to a cantilever and a silicon wafer under ultra high vacuum conditions. In using a silicon surface with a defined structure a correlation between adhesion force and contact area was found. This correlation could partly be explained by the Johnson-Kendall-Roberts model, if a change of the surface energy is assumed as a result of the structuring. For a constant geometric contact area an additional structuring leads to a decrease of the adhesion force. T2 - 10th European Conference on Applications of Surface and Interface Analysis (ECASIA '03) CY - Berlin DA - 2003-10-05 KW - Roughness KW - Adhesion KW - AFM KW - UHV KW - JKR model KW - Surface energy PY - 2004 DO - https://doi.org/10.1002/sia.1738 SN - 0142-2421 SN - 1096-9918 VL - 36 IS - 8 SP - 694 EP - 697 PB - Wiley CY - Chichester AN - OPUS4-4708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löhr, Manuel A1 - Spaltmann, Dirk A1 - Effner, Ute A1 - Woydt, Mathias T1 - Der Einfluss des E-Moduls und des Grundöls auf das Wälzverhalten von DLC- und Diamantbeschichtungen KW - E-Modul KW - Grundöle KW - Wälzen KW - DLC-Schichten PY - 2005 SN - 0724-3472 VL - 52 IS - 1 SP - 32 EP - 36 PB - Expert Verlag CY - Renningen AN - OPUS4-7301 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löhr, Manuel A1 - Spaltmann, Dirk A1 - Effner, Ute A1 - Woydt, Mathias T1 - In-situ-Vergleich wälzbeanspruchter Diamant- und diamantähnlicher Kohlenstoffschichten durch die Akustische Emission KW - Akustische Emission KW - Wälzen KW - Diamantschichten PY - 2005 SN - 0724-3472 VL - 52 IS - 1 SP - 26 EP - 31 PB - Expert Verlag CY - Renningen AN - OPUS4-7302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Löhr, Manuel A1 - Binkowski, Sigrid A1 - Kelling, Norbert A1 - Soltwedel, Rocco A1 - Woydt, Mathias A1 - Santner, Erich T1 - Schäden wälzbeanspruchter DLC-Schichten auf Stahlsubstraten unterschiedlicher Härte N2 - Paraffinöl geschmierte Wälztests wurden an extrem harten Diamantschichten auf hartem SSiC Substrat, unterschiedlichen, harten DLC-Schichten auf 100Cr6 Substraten (HRC60) sowie ausgewählten DLC-Schichten auf ungehärtetem Stahl (HRC 20) durchgeführt. Die Wälztests wurden in einem Zweischeibentribometer vom Typ Amsler bei einer anfänglichen, maximalen Flächenpressung nach Hertz von P0=2,3 GPa ausgeführt. Als Abbruchkriterium für die Tests wurde das Erreichen von n=1.000.000 Überrollungen (Langzeittests n=10.000.000 Überrollungen) oder das Auftreten einer Schädigung mit einer zusammenhängenden Fläche von A>1 mm2 festgelegt. Die Wälztests zeigten, dass das harte SSiC Substrat zwar eine stützende Wirkung auf die Diamantschicht hat, diese aber aufgrund von Rissen im Substrat versagte. Ferner gibt es wenigstens zwei DLC-Schichten, die, aufgebracht auf 100Cr6 Scheiben (HRC60), den Wälztests bis n=10.000.000 Überrollungen ohne nennenswerte Schäden widerstanden. Diese Schichten passten sich auch den Verformungen des weichen, stickstofflegierten Stahls (HRC20) an, ohne das es zu größeren Abplatzungen kam (A>1 mm2). KW - Slip-rolling KW - Lubrication KW - Hardness KW - DLC KW - Steel KW - Wälzen KW - Schmierung KW - Härte KW - DLC KW - Stahl PY - 2005 DO - https://doi.org/10.1002/mawe.200400850 SN - 0933-5137 SN - 1521-4052 VL - 36 IS - 2 SP - 62 EP - 68 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-7209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klaffke, Dieter A1 - Santner, Erich A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Influences on the tribological behaviour of slip-rolling DLC-coatings N2 - Diamond like carbon (DLC)-coatings are applied very successfully on computer discs. Sliding friction tests confirm their high performance as dry lubricants with friction coefficients (COFs) below 0.1. In contrast to sliding tests, until very recently most of the DLC-coatings failed in slip-rolling test after fewer cycles than uncoated samples. However, present tests with DLC-coatings of seven different suppliers show a more promising tribological behaviour under slip-rolling conditions. The DLC-coatings were deposited onto steel 100Cr6, HRC 60, with a thickness of 2–3 ?m. The counter bodies were uncoated, grinded or polished 100Cr6 discs with 30 mm radius of curvature. The tests were performed on a twin disc testing rig (Amsler type) with paraffin oil under boundary/mixed lubrication and rolling with 10% slip. The initial, average Hertzian contact pressure was adjusted to Pm = 1.0, 1.25, and 1.5 GPa. The failure criterion was defined as the occurrence of a single damaged area larger than 1 mm2, which was controlled by optical microscopy (OM). An acoustic emission (AE) measurement system was installed as an additional online control for coating failure. The stressed coatings and the chipping areas were analyzed by OM, SEM, EDX, AFM and Raman spectroscopy. Until now, the results reveal that a large scatter in lifetime of coatings occurs not only between samples of different coaters but also between the samples of one single batch. The highest lifetime reached by a DLC-coating under these testing conditions is 10 × 106 cycles. That is the highest life time for a coating tested under the testing conditions above in our laboratory so far. The following factors were identified to influence the life time of the coatings: coating thickness, interlayer type, topography of the coatings, counter body roughness and mechanical properties. But the most important factor determining the life time of the coatings is that the coating process does produce homogenous layers free of faults. KW - DLC-coatings KW - Slip-rolling KW - Life time KW - Acoustic emission PY - 2005 DO - https://doi.org/10.1016/j.wear.2005.01.008 SN - 0043-1648 VL - 259 SP - 752 EP - 758 PB - Elsevier CY - Amsterdam AN - OPUS4-7557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Santner, Erich A1 - Spaltmann, Dirk T1 - Adhesion of cleaned nanoscopic metal contacts KW - Nanoscopic metal contacts KW - Adhesion KW - Friction KW - Atomic force microscope KW - AFM KW - Theoretical models PY - 2003 SN - 1354-4063 SN - 1557-685X VL - 9-4 SP - 333 EP - 344 PB - Coppin CY - Deal AN - OPUS4-2620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meine, Kerstin A1 - Kloß, Heinz A1 - Schneider, Thomas A1 - Spaltmann, Dirk T1 - Adhäsion an strukturierten Oberflächen N2 - Das tribologische Verhalten wird neben den chemischen und physikalischen Eigenschaften der Reibpartner auch von deren Oberflaechentopographie bestimmt. Um deren Beitrag auf die Reibkraft zu untersuchen, wurden daher definierte Rauheitsstrukturen in Siliziumwafer geaetzt. Reibversuche mit einem Mikrotribometer [1, 2] gaben Aufschluss ueber den Einfluss dieser Strukturen auf das Deformationsverhalten im Kontaktbereich. Mit Hilfe der gewonnenen Daten wurde ein Deformationsmodell entwickelt, das eine Abschaetzung der Reibkraft in Abhaengigkeit von der Rauheit erlaubte. Treten starke Adhaesionskraefte im Reibkontakt auf, ist ein inverter Einfluss der Rauheit auf die Reibkraft zu verzeichnen. Um diesen Verlauf weiter zu charakterisieren, wurden mit einem UHV-AFM Adhaesionsmessungen an strukturierten Siliziumwafern durchgefuehrt. Diese zeigen den Verlauf der Adhaesionskraft in Abhaengigkeit von der Groesse der Kontaktflaeche auf. Ein Vergleich dieser experimentell gefundenen Korrelation mit den klassischen Kontaktmodellen machte dabei den Einfluss der Oberflaechenrauheit auf die Groesse der Adhaesionskraft deutlich. Danach ergab sich, dass bei gleicher Kontaktflaeche, aber unterschiedlicher Rauheit sich die Adhaesionskraefte um bis zu einem Faktor 3 unterscheiden. [1] K. Meine, T. Schneider, D. Spaltmann, E. Santner, Wear, 253, 2002, 725-732 [2] K. Meine, T. Schneider, D. Spaltmann, E. Santner, Wear, 253, 2002, 733-738 T2 - Frühjahrstagung des Arbeitskreises Festkörperphysik bei der DPG CY - Dresden, Deutschland DA - 2003-03-24 PY - 2003 UR - http://old.dpg-tagungen.de/archive/2003/o_6.html SN - 0420-0195 SN - 0372-5448 SN - 0343-9216 IS - O 6.2 SP - 382 CY - Bad Honnef AN - OPUS4-2400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löhr, Manuel A1 - Spaltmann, Dirk A1 - Binkowski, Sigrid A1 - Woydt, Mathias T1 - Einfluss der Topographie von DLC-Schichten auf deren Verhalten unter geschmierter Wälzbeanspruchung KW - Diamant DLC KW - 100Cr6 KW - Wälzen KW - Paraffinöl KW - Topographie KW - Rasterkraftmikroskop PY - 2004 SN - 0724-3472 VL - 51 IS - 6 SP - 18 EP - 26 PB - Expert Verlag CY - Renningen AN - OPUS4-5142 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löhr, Manuel A1 - Spaltmann, Dirk A1 - Binkowski, Sigrid A1 - Santner, Erich A1 - Woydt, Mathias T1 - In situ Acoustic Emission for wear life detection of DLC coatings during slip-rolling friction N2 - Different diamond-like carbon (DLC) coatings on a steel substrate (100Cr6) were tested under slip-rolling friction conditions against uncoated counter bodies of the same steel. The initial maximum Hertzian pressure was varied in a range of P0 = 1.5–2.3 GPa. The friction tests were carried out under dry conditions and with an unadditivated paraffin oil as lubricant. It could be shown that the thickness of the coatings affects the respective wear life. Further, a very important factor for the wear life of a coating under lubricated slip-rolling conditions is the roughness of the surface of the respective counterbody. The wear life tests were monitored by recording in situ the Acoustic Emission (AE) signals. Some causes for a high AE activity could be identified. KW - Wear life KW - Slip-rolling friction KW - Diamond-like carbon (DLC) KW - Acousitc Emission KW - Lubircation KW - Roughness PY - 2006 DO - https://doi.org/10.1016/j.wear.2005.03.009 SN - 0043-1648 VL - 260 IS - 4-5 SP - 469 EP - 478 PB - Elsevier CY - Amsterdam AN - OPUS4-12064 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Hartelt, Manfred A1 - Woydt, Mathias T1 - Ultra-high frequency tribometer for reciprocating sliding motion N2 - A novel tribometer has been designed using commercially available components for sliding motion at 40kHz with amplitude between 2.5 and 5µm. The tribometer is equipped with means to measure amplitude, frequency, power required to keep the sample in motion and load applied. The effective motion between the two contacting bodies is monitored. These data are used to evaluate the coefficient of friction. The wear rate was determined after the tests. The set-up was tested using novel, non-commercial substrates such as AlFeCrTi-alloys and tungsten carbide-based coatings as well as Magnéli-type coatings (Tin-2Cr2O2n-1 and TinO2n-1). This paper presents the principle of the ultra-high frequency tribometer and first tribological quantities of materials and coatings tested. KW - Frequency KW - Tribometer KW - Sliding KW - Friction KW - Wear KW - Aluminium alloy KW - Oscillation KW - Magnéli-type phases PY - 2007 DO - https://doi.org/10.1002/tt.41 SN - 1354-4063 SN - 1557-685X VL - 13 IS - 4 SP - 153 EP - 164 PB - Coppin CY - Deal AN - OPUS4-16047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Löhr, Manuel A1 - Effner, Ute A1 - Scholz, Christian A1 - Manier, Charles-Alix A1 - Woydt, Mathias T1 - Wälzbeständigkeit von diamantartigen Kohlenstoffschichten KW - DLC KW - ZrCN KW - Wälzen KW - Technische Beschichtungen KW - Null-Verschleiß PY - 2011 SN - 1619-5558 VL - 2 IS - 37 SP - 16 EP - 24 PB - Diamond Business KG CY - Bamberg AN - OPUS4-23947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - von Gablenz, C.-H. A1 - Spaltmann, Dirk T1 - Das CargoLifter-Ballonkransystem N2 - Das CargoLifter-Ballonkransystem nutzt die Prinzipien der Leichter-als-Luft-Technologie für das Heben von Gütern. Der mit leichtem Gas gefüllte Ballon drängt in der schwereren Luft nach oben und kann somit Lasten anheben. Im Gegensatz zu erdgebundenen Kranen ist für den Luftkran die Beschaffenheit des Bodens sekundär. Der Ballonkran wird an 3 Winden verankert und über die im Kranknotenpunkt zusammengeführten Seile präzise gesteuert. Beim Heben und Versetzen verbleibt die Last unter dem Ballon, der stets 100 % seiner Hubkraft auch bis zu 200 m Höhe und selbst weiterem Versatz behält. Reichweite bedeutet beim CargoLifter-Ballonkransystem statt mehr Ausleger mehr Seil. PY - 2011 SN - 1866-0207 VL - 123 IS - 12 SP - 34 EP - 38 PB - E. Schmidt, Süddt. Zweigstelle CY - München AN - OPUS4-25332 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kovalev, Alexander A1 - Hartelt, Manfred A1 - Spaltmann, Dirk A1 - Wäsche, Rolf A1 - Woydt, Mathias T1 - Zero wear (Null Verschleiß) KW - Reibung KW - Null-Verschleiß KW - Rauhigkeit KW - Kontaktmechanik KW - Modellierung KW - DLC KW - Friction KW - Zero-wear KW - Roughness KW - Contact mechanics KW - Simulation PY - 2013 SN - 0724-3472 VL - 60 IS - 2 SP - 5 EP - 12 PB - Expert Verlag CY - Renningen AN - OPUS4-28979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meine, Kerstin A1 - Schneider, Thomas A1 - Spaltmann, Dirk A1 - Santner, Erich T1 - The influence of roughness on friction - Part I: The influence of a single step KW - Tribology KW - Roughness KW - Friction force KW - Elastic deformation PY - 2002 SN - 0043-1648 VL - 253 SP - 725 EP - 732 PB - Elsevier CY - Amsterdam AN - OPUS4-1580 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meine, Kerstin A1 - Schneider, Thomas A1 - Spaltmann, Dirk A1 - Santner, Erich T1 - The influence of roughness on friction - Part II: The influence of multiple steps KW - Tribology KW - Roughness KW - Friction force KW - Elastic deformation PY - 2002 SN - 0043-1648 VL - 253 SP - 733 EP - 738 PB - Elsevier CY - Amsterdam AN - OPUS4-1581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kunz, C. A1 - Bonse, Jörn A1 - Spaltmann, Dirk A1 - Neumann, C. A1 - Turchanin, A. A1 - Bartolomé, J. F. A1 - Müller, F. A. A1 - Gräf, S. T1 - Tribological performance of metal-reinforced ceramic composites selectively structured with femtosecond laser-induced periodic surface structures N2 - The impact of femtosecond (fs) laser-induced periodic surface structures (LIPSS) on tribological properties was investigated for metal-reinforced ceramic composites (Al2O3-ZrO2-Nb). For this purpose, the metallic niobium (Nb) phase was selectively structured with LIPSS in an air environment with different values of the fs-laser peak fluence by near-infrared fs-laser radiation (λ = 1025 nm, τ = 300 fs, frep = 1 kHz), taking advantage of the different light absorption behavior of ceramic and metal. The tribological performance was evaluated by reciprocating sliding tests in a ball-on-disc configuration using Ringer's solution as lubricant. The surfaces were characterized before and after laser irradiation by optical microscopy, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy and by measuring the contact angle with Ringer's solution. The LIPSS formation resulted in an increased wetting of the surface with the lubricant. Moreover, the selectively structured composite surfaces revealed a coefficient of friction significantly reduced by a factor of ~3 when compared to the non-irradiated surface. Furthermore, the formation of a laser-induced oxidation layer was detected with NbO as the most prominent oxidation state. Selectively structured composites with outstanding mechanical properties and enhanced tribological performance are of particular interest for biomedical applications. KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Ceramic matrix composites KW - Tribology PY - 2020 DO - https://doi.org/10.1016/j.apsusc.2019.143917 SN - 0169-4332 SN - 1873-5584 VL - 499 IS - 1 SP - 143917 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-49255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl N2 - Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz'schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden. In der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis P0max = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei+120 °C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt KW - Hochzähe Stähle KW - Getriebekomponenten KW - DLC KW - ZrCN KW - Extrembeanspruchung KW - Dünnschichten KW - Polyglykole KW - Additive KW - Slip-rolling KW - High toughness steels KW - High pressure KW - Thin film coatings KW - Polyglycols KW - Additives PY - 2012 SN - 0724-3472 VL - 59 IS - 3 SP - 41 EP - 47 PB - Expert Verlag CY - Renningen AN - OPUS4-26232 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Spaltmann, Dirk A1 - Theiler, Geraldine A1 - Woydt, Mathias T1 - Carboneous coatings by rolling with 10% slip under mixed/boundary lubrication and high initial Hertzian contact pressures N2 - Costs reduction is one of the major objectives in mechanical applications with a parallel increase of the power output. Another driver represents new environmental standards and their increasing restrictions in the automotive industry leading to the question, if materials based concepts may substitute harmful EP/AW additives in lubricants. This paper presents the slip-rolling resistance of different DLC/THC coatings on steel substrates with a definite slip rate of 10%. Industrial DLC coatings of ta-C and a-C:H types from various manufacturers were deposited on steels SAE 52100 and AMS 5898 to compile the slip-rolling resistance under initial average Hertzian contact pressures between 1.5 GPa and 2 GPa. The tests were carried out on Amsler-type twin disc tribometer under the regime of mixed/boundary lubrication in unadditivated paraffinic oil (ISO VG 46) and a factory fill engine oil. The spherical steel sample was uncoated and the cylindrical coated with DLC. Some coatings achieved 10 million cycles without any damage under a maximal Hertzian contact pressure Pmax well over 2.25 GPa, thus exceeding FZG 12. KW - DLC KW - Rolling KW - Mixed/boundary lubrication KW - Hertzian pressure PY - 2008 DO - https://doi.org/10.1016/j.diamond.2008.01.066 SN - 0925-9635 VL - 17 IS - 7-10 SP - 1751 EP - 1754 PB - Elsevier CY - New York, NY AN - OPUS4-17816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Proß, E. A1 - Ziegele, H. A1 - Kursawe, S. A1 - Woydt, Mathias T1 - Überrollbeständige Dünnschichten unter geschmierter Wälzreibung bis 3.500 MPa KW - DLC KW - Kohlenstoff Wälzen KW - Schlupf KW - Schmierung KW - Temperatur KW - Pressung PY - 2008 SN - 0724-3472 VL - 55 IS - 4 SP - 22 EP - 27 PB - Expert Verlag CY - Renningen AN - OPUS4-18029 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Spaltmann, Dirk A1 - Woydt, Mathias A1 - Proß, E. A1 - Ziegele, H. T1 - Couches minces pour les contacts lubrifiés en slip-rolling (glissement-roulement) sous haute pression hertzienne initiale N2 - Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'’à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. ----------------------------------------------------------------------------------------------------------------------------------------------- The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. KW - Thin film coatings KW - DLC KW - Zr(CN) KW - ta-C KW - Slip-rolling KW - Mixed lubrication KW - Couches minces KW - Lubrification mixte PY - 2009 DO - https://doi.org/10.1051/mattech/2009051 SN - 0032-6895 SN - 1778-3771 VL - 97 IS - 6 SP - 397 EP - 409 CY - Paris AN - OPUS4-31747 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Spaltmann, Dirk A1 - Woydt, Mathias A1 - Ziegele, H. T1 - Benchmark of thin film coatings for lubricated slip-rolling contacts N2 - The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of high-performance coatings represents one approach among others. This paper presents some recently developed DLC coatings (a-C:H and ta-C) as well as a novel coating-substrate system (Zr(C,N)) in a benchmark test procedure under slip-rolling conditions in the presence of liquid lubricants. Various coatings with different thickness, interlayer and substrates were evaluated for their slip-rolling resistance in different lubricants at ambient temperature and at 120 °C. Results indicate that some of these coating systems can withstand at least 10 million cycles under initial Hertzian contact pressures of up to Pmax = 3.500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. Surface of the coatings and the counter bodies were analysed and compared with untreated substrates. KW - Slip-rolling KW - DLC KW - Thin film coating KW - Zr(C,N) KW - Polyglycol PY - 2010 DO - https://doi.org/10.1016/j.wear.2010.02.020 SN - 0043-1648 VL - 268 IS - 11-12 SP - 1442 EP - 1454 PB - Elsevier CY - Amsterdam AN - OPUS4-21196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Joseba Ayerdi, J. A1 - Slachciak, Nadine A1 - Llavori, I. A1 - Zabala, A. A1 - Aginagalde, A. A1 - Bonse, Jörn A1 - Spaltmann, Dirk T1 - On the role of a ZDDP in the tribological performance of femtosecond laser-induced periodic surface structures on titanium alloy against different counterbody materials N2 - Laser-induced periodic surface structures (LIPSS, ripples) with ~500–700 nm period were produced on titanium alloy (Ti6Al4V) surfaces upon scan processing in air by a Ti:sapphire femtosecond laser. The tribological performance of the surfaces were qualified in linear reciprocating sliding tribological tests against balls made of different materials using different oilbased lubricants. Extending our previous work, we studied the admixture of the additive 2-ethylhexyl-zinc-dithiophosphate to a base oil containing only anti-oxidants and temperature stabilizers. The presence of this additive along with the variation of the chemical composition of the counterbodies allows us to explore the synergy of the additive with the laseroxidized nanostructures. KW - Additives KW - Surface structures KW - Wear KW - Friction PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-488458 DO - https://doi.org/10.3390/lubricants7090079 SN - 2075-4442 VL - 7 SP - 79, 1 EP - 13 PB - MDPI AN - OPUS4-48845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kirner, Sabrina V. A1 - Slachciak, Nadine A1 - Elert, Anna Maria A1 - Griepentrog, Michael A1 - Fischer, Daniel A1 - Hertwig, Andreas A1 - Sahre, Mario A1 - Dörfel, Ilona A1 - Sturm, Heinz A1 - Pentzien, Simone A1 - Koter, Robert A1 - Spaltmann, Dirk A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Tribological performance of titanium samples oxidized by fs-laser radiation, thermal heating, or electrochemical anodization N2 - Commercial grade-1 titanium samples (Ti, 99.6%) were treated using three alternative methods, (i) femtosecond laser processing, (ii) thermal heat treatment, and (iii) electrochemical anodization, respectively, resulting in the formation of differently conditioned superficial titanium oxide layers. The laser processing (i) was carried out by a Ti:sapphire laser (pulse duration 30 fs, central wavelength 790 nm, pulse repetition rate 1 kHz) in a regime of generating laser-induced periodic surface structures (LIPSS). The experimental conditions (laser fluence, spatial spot overlap) were optimized in a sample-scanning setup for the processing of several square-millimeters large surface areas covered homogeneously by these nanostructures. The differently oxidized titanium surfaces were characterized by optical microscopy, micro Raman spectroscopy, variable angle spectroscopic ellipsometry, and instrumented indentation testing. The tribological performance was characterized in the regime of mixed friction by reciprocating sliding tests against a sphere of hardened steel in fully formulated engine oil as lubricant. The specific tribological performance of the differently treated surfaces is discussed with respect to possible physical and chemical mechanisms. KW - Femtosecond laser KW - Titanium KW - Oxidation KW - Friction PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-445609 DO - https://doi.org/10.1007/s00339-018-1745-8 SN - 0947-8396 SN - 1432-0630 VL - 124 IS - 4 SP - 326, 1 EP - 10 PB - Springer-Verlag AN - OPUS4-44560 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marwitz, Christian A1 - Stegemann, B. A1 - Breitkreiz, Maxim A1 - Spaltmann, Dirk A1 - Kloß, Heinz A1 - Woydt, Mathias A1 - Sturm, Heinz T1 - Correlation of adhesion force and electrical conductivity in Magnéli-type vanadium oxides and highly oriented pyrolytic graphite N2 - A correlation of adhesion force and electrical conductivity is established for a vanadium oxide and highly oriented pyrolytic graphite (HOPG). Adhesion forces were determined by analysis of pull-off forces obtained from force–distance curves with atomic force microscopy in ultrahigh vacuum, on clean surfaces and with defined contact conditions. The investigated samples include (i) different stoichiometries of Magnéli-type vanadium oxides (V3O5, V4O7, V6O11, and V7O13), which undergo metal-insulator-transitions as a function of temperature, (ii) the (0001) basal plane and the (10–10) prism plane of highly oriented pyrolytic graphite (HOPG), which differ in their respective perpendicular-plane electrical conductivities by several orders of magnitude, and (iii) the (100) surfaces of pure metal single crystals, i.e., silver (Ag), copper (Cu), iron (Fe) and gold (Au). It is shown, that the vanadium oxides as well as the graphite exhibit significantly lower adhesion forces in their electrical conductive state than in their non-electrical conductive state. The values obtained for the electrical conductive states are quantitatively confirmed by the measurements on the single crystal metals. KW - Adhesion force KW - HOPG KW - Vanadium oxide KW - Magnéli phases KW - Single crystal metals KW - Atomic force microscopy PY - 2011 DO - https://doi.org/10.1016/j.susc.2011.04.014 SN - 0039-6028 VL - 605 IS - 13-14 SP - 1271 EP - 1274 PB - Elsevier CY - Amsterdam AN - OPUS4-23953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -