TY - JOUR A1 - Spaltmann, Dirk A1 - Löhr, Manuel A1 - Binkowski, Sigrid A1 - Kelling, Norbert A1 - Soltwedel, Rocco A1 - Woydt, Mathias A1 - Santner, Erich T1 - Schäden wälzbeanspruchter DLC-Schichten auf Stahlsubstraten unterschiedlicher Härte JF - Materialwissenschaft und Werkstofftechnik = Materials science and engineering technology N2 - Paraffinöl geschmierte Wälztests wurden an extrem harten Diamantschichten auf hartem SSiC Substrat, unterschiedlichen, harten DLC-Schichten auf 100Cr6 Substraten (HRC60) sowie ausgewählten DLC-Schichten auf ungehärtetem Stahl (HRC 20) durchgeführt. Die Wälztests wurden in einem Zweischeibentribometer vom Typ Amsler bei einer anfänglichen, maximalen Flächenpressung nach Hertz von P0=2,3 GPa ausgeführt. Als Abbruchkriterium für die Tests wurde das Erreichen von n=1.000.000 Überrollungen (Langzeittests n=10.000.000 Überrollungen) oder das Auftreten einer Schädigung mit einer zusammenhängenden Fläche von A>1 mm2 festgelegt. Die Wälztests zeigten, dass das harte SSiC Substrat zwar eine stützende Wirkung auf die Diamantschicht hat, diese aber aufgrund von Rissen im Substrat versagte. Ferner gibt es wenigstens zwei DLC-Schichten, die, aufgebracht auf 100Cr6 Scheiben (HRC60), den Wälztests bis n=10.000.000 Überrollungen ohne nennenswerte Schäden widerstanden. Diese Schichten passten sich auch den Verformungen des weichen, stickstofflegierten Stahls (HRC20) an, ohne das es zu größeren Abplatzungen kam (A>1 mm2). KW - Slip-rolling KW - Lubrication KW - Hardness KW - DLC KW - Steel KW - Wälzen KW - Schmierung KW - Härte KW - DLC KW - Stahl PY - 2005 DO - https://doi.org/10.1002/mawe.200400850 SN - 0933-5137 SN - 1521-4052 VL - 36 IS - 2 SP - 62 EP - 68 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-7209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Proß, E. A1 - Ziegele, H. A1 - Kursawe, S. A1 - Woydt, Mathias T1 - Überrollbeständige Dünnschichten unter geschmierter Wälzreibung bis 3.500 MPa JF - Tribologie und Schmierungstechnik KW - DLC KW - Kohlenstoff Wälzen KW - Schlupf KW - Schmierung KW - Temperatur KW - Pressung PY - 2008 SN - 0724-3472 VL - 55 IS - 4 SP - 22 EP - 27 PB - Expert Verlag CY - Renningen AN - OPUS4-18029 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Spaltmann, Dirk A1 - Theiler, Geraldine A1 - Woydt, Mathias T1 - Carboneous coatings by rolling with 10% slip under mixed/boundary lubrication and high initial Hertzian contact pressures JF - Diamond and related materials N2 - Costs reduction is one of the major objectives in mechanical applications with a parallel increase of the power output. Another driver represents new environmental standards and their increasing restrictions in the automotive industry leading to the question, if materials based concepts may substitute harmful EP/AW additives in lubricants. This paper presents the slip-rolling resistance of different DLC/THC coatings on steel substrates with a definite slip rate of 10%. Industrial DLC coatings of ta-C and a-C:H types from various manufacturers were deposited on steels SAE 52100 and AMS 5898 to compile the slip-rolling resistance under initial average Hertzian contact pressures between 1.5 GPa and 2 GPa. The tests were carried out on Amsler-type twin disc tribometer under the regime of mixed/boundary lubrication in unadditivated paraffinic oil (ISO VG 46) and a factory fill engine oil. The spherical steel sample was uncoated and the cylindrical coated with DLC. Some coatings achieved 10 million cycles without any damage under a maximal Hertzian contact pressure Pmax well over 2.25 GPa, thus exceeding FZG 12. KW - DLC KW - Rolling KW - Mixed/boundary lubrication KW - Hertzian pressure PY - 2008 DO - https://doi.org/10.1016/j.diamond.2008.01.066 SN - 0925-9635 VL - 17 IS - 7-10 SP - 1751 EP - 1754 PB - Elsevier CY - New York, NY AN - OPUS4-17816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Spaltmann, Dirk A1 - Woydt, Mathias A1 - Proß, E. A1 - Ziegele, H. T1 - Couches minces pour les contacts lubrifiés en slip-rolling (glissement-roulement) sous haute pression hertzienne initiale JF - Matériaux et techniques N2 - Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'’à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. ----------------------------------------------------------------------------------------------------------------------------------------------- The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. KW - Thin film coatings KW - DLC KW - Zr(CN) KW - ta-C KW - Slip-rolling KW - Mixed lubrication KW - Couches minces KW - Lubrification mixte PY - 2009 DO - https://doi.org/10.1051/mattech/2009051 SN - 0032-6895 SN - 1778-3771 VL - 97 IS - 6 SP - 397 EP - 409 CY - Paris AN - OPUS4-31747 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Spaltmann, Dirk A1 - Woydt, Mathias A1 - Ziegele, H. T1 - Benchmark of thin film coatings for lubricated slip-rolling contacts JF - Wear N2 - The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of high-performance coatings represents one approach among others. This paper presents some recently developed DLC coatings (a-C:H and ta-C) as well as a novel coating-substrate system (Zr(C,N)) in a benchmark test procedure under slip-rolling conditions in the presence of liquid lubricants. Various coatings with different thickness, interlayer and substrates were evaluated for their slip-rolling resistance in different lubricants at ambient temperature and at 120 °C. Results indicate that some of these coating systems can withstand at least 10 million cycles under initial Hertzian contact pressures of up to Pmax = 3.500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. Surface of the coatings and the counter bodies were analysed and compared with untreated substrates. KW - Slip-rolling KW - DLC KW - Thin film coating KW - Zr(C,N) KW - Polyglycol PY - 2010 DO - https://doi.org/10.1016/j.wear.2010.02.020 SN - 0043-1648 VL - 268 IS - 11-12 SP - 1442 EP - 1454 PB - Elsevier CY - Amsterdam AN - OPUS4-21196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Slip-rolling resistance of thin films and high toughness steel substrates under high Hertzian contact pressures JF - Wear N2 - Diamond-like carbon (DLC) coatings are perceived as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear and engine components. Therefore, in previous investigations amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings were inspected. For up to ten million cycles at Hertzian contact pressures P0max of 2.9 GPa it was shown that these coatings are slip-rolling resistant not only at room temperature in the presence of unaddivated paraffin oil, but also up to 120 °C oil temperature. The steel substrates in this investigation were made of the hardened and tempered steels 100Cr6H and Cronidur 30. The aim of the current work is manifold. The Hertzian contact pressures should be increased up to P0max of 4.2 GPa by using new steel metallurgies as substrates for thin film coatings. These steel metallurgies are also assessed, if they can compete as uncoated couples. Two high toughness spring steels and an ultra-high toughness aerospace steel were tested in a twin disc tribometer of the Amsler type as well as in an Optimol 2Disk test rig under mixed/boundary conditions in a factory fill SAE 0W-30 engine oil. Different factors such as influences of the lubrication, surface chemistry and wear behaviour were investigated. KW - Slip-rolling KW - High toughness steel KW - DLC KW - ZrCN KW - Thin film coating KW - High pressure PY - 2011 DO - https://doi.org/10.1016/j.wear.2011.01.005 SN - 0043-1648 VL - 270 IS - 7-8 SP - 506 EP - 514 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Löhr, Manuel A1 - Effner, Ute A1 - Scholz, Christian A1 - Manier, Charles-Alix A1 - Woydt, Mathias T1 - Wälzbeständigkeit von diamantartigen Kohlenstoffschichten JF - Diamond business KW - DLC KW - ZrCN KW - Wälzen KW - Technische Beschichtungen KW - Null-Verschleiß PY - 2011 SN - 1619-5558 VL - 2 IS - 37 SP - 16 EP - 24 PB - Diamond Business KG CY - Bamberg AN - OPUS4-23947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl JF - Tribologie und Schmierungstechnik KW - Hochzähe Stähle KW - Getriebekomponenten KW - DLC KW - ZrCN KW - Extrembeanspruchung KW - Dünnschichten KW - Polyglykole KW - Additive KW - Slip-rolling KW - High toughness steels KW - High pressure KW - Thin film coatings KW - Polyglycols KW - Additives PY - 2012 SN - 0724-3472 VL - 59 IS - 3 SP - 41 EP - 47 PB - Expert Verlag CY - Renningen AN - OPUS4-26232 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kovalev, Alexander A1 - Hartelt, Manfred A1 - Spaltmann, Dirk A1 - Wäsche, Rolf A1 - Woydt, Mathias T1 - Zero wear (Null Verschleiß) JF - Tribologie und Schmierungstechnik KW - Reibung KW - Null-Verschleiß KW - Rauhigkeit KW - Kontaktmechanik KW - Modellierung KW - DLC KW - Friction KW - Zero-wear KW - Roughness KW - Contact mechanics KW - Simulation PY - 2013 SN - 0724-3472 VL - 60 IS - 2 SP - 5 EP - 12 PB - Expert Verlag CY - Renningen AN - OPUS4-28979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -