TY - RPRT A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris A1 - Schneider, Uwe A1 - Krocker, Christian A1 - Kalus, Sabine A1 - Seeger, Stefan A1 - Bücker, Michael T1 - Prüfung von Emissionen aus Bürogeräten während der Druckphase zur Weiterentwicklung des Umweltzeichens Blauer Engel für Laserdrucker und Multifunktionsgeräte unter besonderer Berücksichtigung der Sicherung guter Innenraumluftqualität T2 - Umweltforschungsplan des Bundesministeriums für Umwelt, Naturschutz und Reaktorsicherheit - Förderkennzeichen (UFOPLAN) 204 95 373 / UBA-FB 001159 - Abschlussbericht / UBA-Texte KW - Emissionen KW - Emissionsmesskammern KW - VOC KW - TVOC KW - Ozon KW - Staub KW - RAL-UZ 122 KW - Blauer Engel KW - Bürogerät KW - Laserdrucker KW - Partikel PY - 2008 UR - http://www.umweltbundesamt.de/publikationen/pruefung-von-emissionen-aus-buerogeraeten-waehrend SN - 1862-4804 VL - 35 IS - 8 SP - 1 EP - 164 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-18265 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seeger, Stefan A1 - Bresch, Harald T1 - Partikelemissionen aus Laserdruckern auf der Spur JF - Labor-Praxis KW - Laserdrucker KW - Ultrafeinstaub KW - Partikelemission PY - 2008 SN - 0344-1733 SN - 1610-8256 IS - 4 SP - 26 EP - 28 PB - Vogel CY - Würzburg AN - OPUS4-18563 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Werner A1 - Jakob, Ines A1 - Seeger, Stefan A1 - Tatzky-Gerth, Renate T1 - Long-term shear strength of geosynthetic clay liners JF - Geotextiles and Geomembranes N2 - Geosynthetic clay liners (GCLs) often have a sandwich-like multilayer structure, e.g. bentonite encased between two geotextile layers connected by fibers or yarns, either by needle-punching or stitch-bonding. Therefore, the internal shear strength of the GCL depends on the strength of reinforcing fiber bundles or yarns and their anchoring strength in the cover and carrier geotextiles. When used on long and steep slopes and covered with thick soil layers, the GCL is permanently exposed to a combined action of compressive and shear stress. Such load conditions are characteristic for landfill covers and the slope stability of the overall cover system in the long run strongly depends on the long-term internal shear strength of the GCL. A new test method was developed to study this long-term shear behavior. The focus was not only on creep, as it is normally done, but on aging effects. The shear test devices allow the measurement of creep curves and times-to-failure at elevated temperatures in different media (tap water and de-ionized water). In this publication, the main findings of the experiments on needle-punched GCLs with and without thermal treatment are summarized. Tap water as a test medium was essential to ensure sodium to calcium ion exchange in the bentonite layer. Under this condition extremely long test durations without failure were achieved. Sliding failure occurred when de-ionized water was used. Two failure modes were observed: brittle failure of the GCLs with thermal treatment and slow disentanglement of fiber bundles for untreated GCLs. Short-term shear strength (e.g. peel strength) is unrelated to the actual long-term shear strength, i.e. to the times-to-failure achieved in long-term shear strength test. Hence, short-term shear strength alone will not provide reliable dimensioning data for product design and choice of resins. Therefore, the often suggested approach, namely, restriction to short-term tests only and application of factors of safety, is challenged by these results. KW - Geosynthetic clay liner KW - Shear strength KW - Oxidative resistance KW - Test methods KW - Long-term testing PY - 2008 DO - https://doi.org/10.1016/j.geotexmem.2007.08.001 SN - 0266-1144 VL - 26 IS - 2 SP - 130 EP - 144 PB - Elsevier CY - Amsterdam AN - OPUS4-16710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan A1 - Wilke, Olaf T1 - Prüfkammermessungen zur Erfassung von VOC- und Partikelemissionen aus Laserdruckern T2 - 15. WaBoLu-Innenraumtage des Vereins für Wasser-, Boden- und Lufthygiene e. V., Gelsenkrichen, Umweltbundesamt T2 - 15. WaBoLu-Innenraumtage des Vereins für Wasser-, Boden- und Lufthygiene e. V., Gelsenkrichen, Umweltbundesamt CY - Berlin, Germany DA - 2008-04-28 PY - 2008 AN - OPUS4-18549 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Seeger, Stefan A1 - Bresch, Harald A1 - Brödner, Doris A1 - Juritsch, Elevtheria A1 - Jann, Oliver T1 - Sampling and characterisation of ultra fine particles released from laser printers T2 - Indoor Air 2008, 11th International Conference on Indoor Air Quality and Climate, August 17-22, 2008, Copenhagen, Denmark (Proceedings) T2 - Indoor Air 2008, August 17-22, 2008 CY - Copenhagen, Denmark DA - 2008-08-17 KW - Aerosol KW - Ultra fine particle KW - Laser printer KW - Cyclosiloxanes PY - 2008 IS - Paper ID: 239 SP - 1 AN - OPUS4-17865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -