TY - CONF A1 - Schröpfer, Dirk T1 - Fachvortrag: Innovative Probenherstellungim Lichte der Proben-Bauteil-Beziehungen N2 - Der Vortrag erörtert die aktuellen fachlichen Herausforderungen und Ziele in der Zentralwerkstatt/FB9.2 der BAM für den Helmholtz-AK "Bau wissenschaftlicher Geräte" T2 - Helmholtz-Arbeitskreis "Bau wissenschaftlicher Geräte", 18. Jahrestagung CY - Berlin, Germany DA - 10.05.2023 KW - Probenfertigung KW - Erneuerbare Energien KW - Additive Fertigung KW - Wasserstoff-Sicherheit PY - 2023 AN - OPUS4-59263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Beanspruchungen bei der Fertigung hochfester Komponenten N2 - Hochfeste und -warmfeste Legierungen nehmen in vielen Bereichen des Maschinen- und Anlagenbaus eine immer größere Rolle ein, deren Wirtschaftlichkeit und Effizienz durch eine kostensparende und präzise fügetechnische und abtragende Fertigung bestimmt wird. Komponenten aus modernen hochfesten Werkstoffen erfordern aufgrund ihres spezifischen Legierungskonzeptes und Gefüges und der oft hohen thermo-mechanischen Belastungen speziell adaptierte Fertigungsabläufe. Der Beitrag stellt einige Themenschwerpunkte vor, bei denen fertigungsbedingte Beanspruchungen und Eigenschaftsdegradationen an hochinnovativen Werkstoffen optimiert und wirtschaftliche Fertigungsbedingungen untersucht werden. T2 - Forschungsseminar OVGU CY - Magdeburg, Germany DA - 15.11.2018 KW - Eigenspannungen KW - MAG-Schweißen KW - Hochfeste Feinkornbaustähle KW - Bauteilprüfung KW - Zerspanung KW - HEA KW - Hochtemperaturwerkstoffe PY - 2018 AN - OPUS4-46608 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Beanspruchungen bei der Fertigung hochfester Komponenten N2 - Hochfeste und -warmfeste Legierungen nehmen in vielen Bereichen des Maschinen- und Anlagenbaus eine immer größere Rolle ein, deren Wirtschaftlichkeit und Effizienz durch eine kostensparende und präzise fügetechnische und abtragende Fertigung bestimmt wird. Komponenten aus modernen hochfesten Werkstoffen erfordern aufgrund ihres spezifischen Legierungskonzeptes und Gefüges und der oft hohen thermo-mechanischen Belastungen speziell adaptierte Fertigungsabläufe. Der Beitrag stellt einige Themenschwerpunkte vor, bei denen fertigungsbedingte Beanspruchungen und Eigenschaftsdegradationen an hochinnovativen Werkstoffen optimiert und wirtschaftliche Fertigungsbedingungen untersucht werden. T2 - Forschungsseminar, Access, Aachen CY - Aachen, Germany DA - 19.11.2018 KW - Bauteilprüfung KW - Eigenspannungen KW - Hochfeste Feinkornbaustähle KW - HEA KW - Hochtemperaturwerkstoffe KW - MAG-Schweißen KW - Zerspanung PY - 2018 AN - OPUS4-47723 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Beanspruchungsgerechtes ultraschallunterstütztes Fräsen Generativ gefertigter Turbinenbauteile N2 - Die Beschaffung und Verarbeitung von Werkstoffen für hochbelastete Komponenten sind meist kostenintensiv. Bestrebungen zur Kosten- und Ressourceneffizienz führen zu komplexeren Strukturen bzw. Konturen, sodass generative Fertigungsschritte zur Bauteilreparatur und -fertigung deutliche ökonomische Vorteile bieten. Hierfür sind generative und abtragende Fertigungsschritte komplementär und gezielt aufeinander abzustimmen, um beanspruchungsgerechte Funktionsflächen herzustellen. T2 - Forschungsseminar, TU Clausthal (ISAF) CY - Clausthal-Zellerfeld, Germany DA - 31.01.2018 KW - Eigenspannungen KW - Auftragschweißen KW - Zerspanung KW - Ultraschallunterstütztes Fräsen KW - Generative Fertigung PY - 2018 AN - OPUS4-47724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Neues aus der BAM / Fachbereich 9.2 N2 - In dieser Präsentation werden die neuesten Herausforderungen und der Stand des Fachbereiches 9.2 für die Mitarbeit im AK des HGF "Bau wissenschaftlicher Geräte" dargestellt. Hierfür werden Neuigkeiten aus dem Bereich Materialprüfung in der BAM präsentiert und mit den Arbeiten der Zentralwerkstatt, die hierfür notwendig sind, in Zusammenhang gebracht. T2 - Helmholtz-Arbeitskreis "Bau wissenschaftlicher Geräte" CY - Berlin, Germany DA - 12.06.2024 KW - Fertigungsverfahren KW - Fertigungskompetenz PY - 2024 AN - OPUS4-62293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Helmholtz-AK "Bau wissenschaftlicher Geräte" - Neues aus der BAM / Fachbereich 9.2 N2 - In dieser Präsentation werden die neuesten Herausforderungen und der Stand des Fachbereiches 9.2 für die Mitarbeit im AK des HGF "Bau wissenschaftlicher Geräte" dargestellt. T2 - Helmholtz-Arbeitskreis "Bau wissenschaftlicher Geräte", 18. Jahrestagung CY - Berlin, Germany DA - 10.05.2023 KW - Werkstatt KW - Erneuerbare Energien PY - 2023 AN - OPUS4-59262 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Studies on the pore formation in super duplex stainless steel welds N2 - When welding super duplex stainless steels a non-admissible pore formation can occur even if recommended processing guidelines are followed strictly. To investigate this phenomenon and to determine the influencing factors different claddings were produced using gas metal arc welding and submerged arc welding. The welding consumables, the shielding gas and the welding flux were varied. As shielding gases several mixtures, based on argon and 30 % helium, with various amounts of nitrogen, nitric oxide, carbondioxid and oxygen were applied. As welding flux agglomerated fluoride basic fluxes and aluminate fluoride basic fluxes were used. Different batches of the similar solid filler wire G 25 9 4 N L were used to produce the claddings on the base material UNS32750. To determine the pore formation X-ray examinations and microsections were used, to analyze the chemical composition of the claddings melt extractions and spectrometric examinations were applied. Additionally, the microhardness and the ferrite number were detected. The studies have shown the shielding gas, the welding flux and the filler metal possess a great influence on the pore formation. Even small variations in the chemical composition of the welding consumables lead to totally different results. In addition, the ferrite number and the chemical composition of the claddings depend strongly on the used gases and filler metals. T2 - IIW Intermediate Meeting, C-IIA CY - Madrid, Spain DA - 29.02.2016 KW - Cladding KW - Welding KW - Duplex stainless steels KW - Pore formation PY - 2016 AN - OPUS4-38786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Reichel, Levin A1 - Schröpfer, Dirk A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Modern welding processes for optimising repair welds on high strength offshore steels N2 - The successful energy transition in Germany will require offshore wind turbines with outputs >10 MW in the future. To achieve these high outputs, turbines far from coast are required with large subsea jacket structures (30 m up to 50 m) and tall towers (up to 200 m). High-strength steels with a yield strength up to 500 MPa and wall thicknesses up to 150 mm are increasingly being used for these structures. This plac-es high demands on welding manufacturing, especially for high-strength offshore steels. During the manu-facturing process detected defects by NDT require localized repair of welds by gouging and rewelding. Due to a lack of investigations, there are no repair concepts and information in standards and guidelines, par-ticularly for high-strength thick plate joints made of high-strength offshore steels. However, these are ur-gently needed to enable manufacturers, especially SMEs, to carry out safe and economical repairs. There-fore, BAM started the FOSTA project P1629 (IGF 01IF22746N) to investigate the stress-optimized repair (local gouging and welding) of high-strength thick plate joints made of offshore grades in the yield strength range off 355 to 460 MPa and similar weld metal with controlled high-performance GMAW pro-cesses and optimized narrow gouging grooves. The experimental analyses take into account the complex interaction of process, material, and design-related influences on the formation of weld induced stresses and the special microstructure of high-strength fine-grain structural steels. Welding-related material degra-dation and crack-critical residual tensile stresses need to be avoided to ensure high component safety and performance. A reduction in residual stress in the presence of high restraint conditions can be achieved by adapted heat control (if no disassembly measures are possible). The repair process involves manual thermal gouging, which allows the groove configuration to be modi-fied. Modern welding processes using high frequency arc control provide deep root penetration and focused energy input capable of welding narrow seams. A comparison was made between the traditional weld con-figuration with a wide 45° groove and transition arc welding and a narrow 30° groove with modern welding process. Even in the case of free shrinkage specimens, the narrow groove weld exhibits a significant reduc-tion of residual stresses, cf. Figure 1, especially in the HAZ and toward the adjacent base material. This can be attributed to the lower weld metal volume needed and the reduction of heat input per layer due to the controlled arc process. For the purposes of this comparison, the same weld seam build-up (but different number of layers) has been applied to both seam configurations. Note that in industrial application (manu-al welding), the wider groove would be welded with several off-center weld beads with conventional weld-ing process. In this analysis this would cause asymmetric effects regarding the residual stress state, diffi-cult to compare to each other. Component-related welding experiments on special testing equipment, adapted process and heat control concepts along with variable groove configurations will be developed and recommendations for guidelines elaborated. This is the prerequisite for fully utilizing the strength potential of high-strength steels and making a valuable contribution to the energy transition in Germany, especially for steel-processing SMEs. T2 - IIW Intermediate Meeting CII CY - Trollhättan, Sweden DA - 10.03.2025 KW - Repair welding KW - Gouging KW - Residual stress KW - Offshore wind turbines KW - High-strength steels PY - 2025 AN - OPUS4-62743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Tim A1 - Diese, Marcel A1 - Rhode, Michael A1 - Schröpfer, Dirk T1 - Characterization of cracking phenomena in TIG welds of high and medium entropy alloy N2 - Multi-element systems with defined entropy (HEA - High Entropy Alloy or MEA - Medium Entropy Alloy) are rather new material concepts that are becoming increasingly important in materials research and development. Some HEA systems show significantly improved properties or combinations of properties, e.g., the overcome of the trade-off between high strength and ductility. Thus, the synthesis, the resulting microstructures, and properties of HEA have been primarily investigated so far. In addition, processing is crucial to achieve a transfer of potential HEA/MEA materials to real applications, e.g. highly stressed components. Since fusion welding is the most important joining process for metals, it is of vital importance to investigate the weldability of these materials. However, this has rarely been the subject of research up to date. For that reason, in this work the weldability depending on the surface preparation of a CoCrFeMnNi-HEA and a CoCrNi-MEA for TIG welding is investigated. The fusion welding of longer plates is described here for the first time for the CoCrNi alloy. The welds of both materials showed distinct formation of cracks in the heat affected zone (HAZ). Optical and scanning electron microscopy analysis clearly confirmed an intergranular fracture topography. But based on the results, the crack mechanism cannot be conclusively clarified as either a liquid metal embrittlement (LME) or hot cracking like liquid film separation occurred. T2 - 2nd International Conference on Advanced Joining Processes CY - Online meeting DA - 21.10.2021 KW - High Entropy Alloy KW - TIG welding KW - Cracking PY - 2021 AN - OPUS4-53607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Formation of multi-axial welding stresses due to material behaviour during fabrication of high-strength steel components N2 - Today an expanding application of high-strength steels in modern welded constructions can be observed. The economical use of these steel grades largely depends on the strength and reliability of the weldments. Therefore the special microstructure and mechanical properties of these grades have to be taken into account by keener working ranges regarding the welding parameters. However, performance and safety of welded components are strongly affected by the stresses occurring during and after welding fabrication locally in the weld seam and globally in the whole component, especially if the shrinkage and distortion due to welding are restrained. Some extensive studies describe the optimization of the welding stresses and the metallurgical effects regarding an adapted welding heat control. In particular lower working temperatures revealed to be effective to significantly reduce the local and global welding induced residual stresses of the completed weld. However, decreased interpass temperatures cause concurrently higher stresses during welding fabrication. This work shows some strategies to reduce these in-process stresses. With help of multi-axial welding stress analyses in component-related weld tests using a special 2-MN-testing facility differences in stress build-up are described in detail for root welds, filler layers and subsequent cooling to ambient temperature. T2 - IIW Intermediate Meeting, C-II-A CY - Trollhättan, Sweden DA - 06.03.2017 KW - Residual stresses KW - GMA Welding KW - High-strength steels KW - Process parameters KW - Restraint PY - 2017 AN - OPUS4-41066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -