TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Einfluss der Verarbeitungstemperatur auf die Eigenschaften von SVB bei Verwendung von Fließmittel und weiteren Zusatzmitteln N2 - Nachdem vor ca. 20 Jahren in Japan die Entwicklung der selbstverdichtenden Betone begann, dauerte es weitere 10 Jahre, bis diese Entwicklung auch Europa erreichte. Obwohl im Fertigteilsektor bereits deutlich mehr SVB zum Einsatz kommt als im Transportbetonbereich, bleiben die Produktionsmengen hinter dem zurück, was die Potenziale und Chancen dieser Technologie eigentlich erwarten ließen. Eine Ursache für die geringe Marktverbreitung sind die stark schwankenden und teilweise nur schwer beherrschbaren Frischbetoneigenschaften dieser Betone. KW - SVB KW - SCC KW - Zusatzmittel KW - Rheologie KW - Fließmittel Betontechnologie KW - Frischbetoneigenschaften PY - 2007 SN - 0373-4331 IS - 12 SP - 40 EP - 49 PB - Bauverl. BV CY - Gütersloh AN - OPUS4-16444 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Ramge, Peter A1 - Kühne, Hans-Carsten T1 - Efecto de las condiciones de almacenamiento del cemento en las propiedades de procesamiento y endurecimiento del hormigón / As consequências das condicoes de armazenamento do cimento nas qualidades do processamento e endurecimento do concreto PY - 2009 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Spanisch/Portugiesisch - Languages: Spanish/Portuguese VL - 3 SP - 2 EP - 9 PB - Bauverl. CY - Gütersloh AN - OPUS4-20239 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Alexander, Mark A1 - John, Vanderley T1 - Education for sustainable use of cement based materials N2 - Structural design and application have always been linked to the compressive strength of concrete as the main relevant criterion. This was justifiable in the past, where concrete consisted of water, ordinary Portland cement and aggregates, but this concept is no longer relevant for modern and more sustainable cement and concrete. Despite these new developments, existing standards, guidelines and academic curricula have not been much updated and are still used worldwide. There is a need to change this situation by proper education of the users. This overview describes the challenges that arise at a user Level from the higher complexity of modern concrete, and defines needs and requirements for enhanced applicability of sustainable concrete concepts. Furthermore, recommendations are given on how better concrete practice can be communicated to all the involved parties, from civil and design engineers to constructors and site-appliers on the construction site. KW - Cement KW - Concrete KW - Sustainability KW - Environment KW - Carbon footprint KW - Education KW - Climate PY - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0008884616307189?via%3Dihub DO - https://doi.org/10.1016/j.cemconres.2017.08.009 SN - 0008-8846 SN - 1873-3948 VL - 114 SP - 103 EP - 114 PB - Elsevier AN - OPUS4-47673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Uzoegbo, H. C. T1 - Building practice and concrete infrastructure development in eastern and southern Africa N2 - The construction sector has traditionally been a source of employment in African regions. However, due to policy changes, cut backs in public investments as well as a fall in the number of employments in the private sector have been observed in many countries. Furthermore a shift from registered companies to informal contractors could be noticed. Many contractors offer services they do not provide permanently or for which the required equipment has to be borrowed. A study that was published in 2000 about the situation in Tanzania pointed out that only ca. 15% of the enterprises that offer concrete works own a concrete mixer. The building practice with concrete varies widely over the African continent. Whereas the level of technology and the infrastructure for cement and concrete in South Africa is elaborate, in East Africa and particularly those that were heavily suffering from civil war during the nineties of the last century, the availability of cement and concrete is poor and these materials are far from being everyday building practice. Most of the population relies on indigenous forms of construction requiring wood obtained from felling of forest trees and ultimately contributing to de-forestation. Informal settlements in South-Africa and Kenya are literal evidence where originally green natural vegetation has been turned into artificial desert-like landscapes. PY - 2011 SN - 1437-9023 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 3 SP - 32 EP - 37 PB - ad-media-Verl. CY - Köln AN - OPUS4-25360 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - EN 206:2014: Cusum method or mean value criterion? / EN 206:2014: Kusum-Verfahren oder Mittelwertkriterium? N2 - Für die Anforderungen an Beton für Gebäude und higenieurbauwerke gilt seil Juli 2014 die EN 206:2.014 anstelle der EN 206-1:2000. In diesem Zusammenhang werden .sogenannte Kontrollkarten für den Konfonnltätsniiehweis zugclassen. Die EN 2.06:2.014 bezeichnet die Verwendung ilcs Mittelwertkritcriuins als Methode B und die Verwen düng von Kontrollkarten als Methode C. Kontrollkarten auf Basis von kumulativen Summen (Kiisum) sind sehr effektive Methoden zur Produktionsstcuerung. Die Anwendung wird In BS 5703-2:2001 geregelt. In England. Südafrika und Australien sind Kusum-Kontrollkartensystcme int Alltag der Betonherstcller etabliert, allerdings dient deren Anwendung nicht dem konkreten Konfbrmitätsnachweis, sondern der Abstimmung einer stabilen und zugleich wirtschafllichcn Produktion. Eine Einführung von Kusum-basierten Kontrollkarten für die Konformitätsbewertung wirft insofern die berechtigte Frage auf, ob das Nachweissystem gleichwertig mit dem bewährten Mittelwertkriterium ist. Im vorliegenden Artikel sollen zunächst kurz die Funktionsweise und die Vorteile von Kusum-Kontrollkarien dargcstclll werden, bevor eine vergleichende Bewertung von Kusum-Mcthode und Mittclwcrtkriterium dun hgelührl wird. KW - EN 206:2014 KW - Cusum method KW - Mean value criterion PY - 2014 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 80 IS - 12 SP - 24 EP - 31 PB - Bauverl. CY - Gütersloh AN - OPUS4-33576 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paul, S.C. A1 - Pirskawetz, Stephan A1 - Van Zijl, G.P.A.G. A1 - Schmidt, Wolfram T1 - Acoustic emission for characterising the crack propagation in strain-hardening cement-based composites (SHCC) N2 - This paper presents the analysis of crack propagation in strain-hardening cement-based composite (SHCC) under tensile and flexural load by using acoustic emission (AE). AE is a non-destructive technique to monitor the development of structural damage due to external forces. The main objective of this research was to characterise the cracking behaviour in SHCC in direct tensile and flexural tests by using AE. A better understanding of the development of microcracks in SHCC will lead to a better understanding of pseudo strain-hardening behaviour of SHCC and its general performance. ARAMIS optical deformation analysis was also used in direct tensile tests to observe crack propagation in SHCC materials. For the direct tensile tests, SHCC specimens were prepared with polyvinyl alcohol (PVA) fibre with three different volume percentages (1%, 1.85% and 2.5%). For the flexural test beam specimens, only a fibre dosage of 1.85% was applied. It was found that the application of AE in SHCC can be a good option to analyse the crack growth in the specimens under increasing load, the location of the cracks and most importantly the identification of matrix cracking and fibre rupture or slippage. KW - Acoustic emission KW - Crack Detection (B) KW - Microcracking (B) KW - Fibre Reinforcement (E) KW - Tensile Properties (C) PY - 2015 DO - https://doi.org/10.1016/j.cemconres.2014.12.003 SN - 0008-8846 SN - 1873-3948 VL - 69 SP - 19 EP - 24 PB - Pergamon Press CY - New York, NY AN - OPUS4-33579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Mota, Berta A1 - Ramirez Caro, Alejandra T1 - Einfluss der gesteinskörnung auf die Rheologie von Beton N2 - Die meisten Einflüsse auf die Rheologie von Beton wirken auf sehr kleinen Skalenebenen. Einflussgrößen im Millimeter oder Zentimeterbereich sind im Wesentlichen auf den Sand und die Gesteinskörnung beschränkt. Letztere machen aber in den meisten Betonen 50 %-70 % des Gesamtvolumens aus, was bei Untersuchungen zur Steuerung der Verarbeitungseigenschaften von Beton häufig vernachlässigt wird. Während Betonzusatzmittel und Zusatzstoffe bei geeigneter Wahl die Rheologie sehr gezielt beeinflussen können, eignen sich Sand und Gesteinskörnung weniger gut zur Steuerung der Rheologie, aber sie tragen zur Rheologie des Gesamtsystems bei. Hierbei können Effekte aus Sand und Gesteinskörnung die Effekte von Zusatzmitteln und Zusatzstoffen überlagern und im ungünstigsten Falle sogar nahezu unwirksam machen. Deshalb sollten Ergebnisse zur Verarbeitbarkeit von Bindemittelsystemen nur mit großer Sorgfalt auf Beton übertragen werden. Es ist wichtig, den Einfluss des Sandes und der Gesteinskörnung besser zu verstehen, um diese so abzustimmen, dass sie Effekte aus Fließmitteln positiv ergänzen anstatt diesen entgegenzuwirken. Durch eine gezielte Abstimmung lassen sich Kosten wirksam sparen. KW - Gesteinskörnung KW - Rheologie KW - Fließgrenze KW - Viskosität KW - Beton PY - 2018 VL - 3 SP - 42 EP - 51 PB - ad-media GmbH CY - Köln AN - OPUS4-47044 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stroh, Julia A1 - Schlegel, Moritz-Caspar A1 - Schmidt, Wolfram A1 - Nguyen, Thi Yen A1 - Meng, Birgit A1 - Emmerling, Franziska T1 - Time-resolved in situ investigation of Portland cement hydration influenced by chemical admixtures N2 - Numerous admixtures are used in the building practice to customize the properties of the cement paste during application. The influences of admixtures on the course of cement hydration and formation of hydrate phases have to be considered. Polycarboxylate ether (PCE) based polymeric superplasticizers (SPs) are known to retard the setting of the cement paste. The extent of the retardation differs depending on the molecular structure of the SP. Additionally, the presence of a stabilizing agent (SA) in the cement paste has a retarding side effect on the setting. The initial cement hydration processes and the detailed mechanisms of the retardation influenced by PCEs, as well as their interactions with particular SAs, are insufficiently understood. Up to now, only the results of phenomenological studies were taken into account to describe this retardation process. A detailed structure analysis monitoring the change of the phase composition during the hydration was never applied. Both SP and SA affect the adsorption of the sulphate ions on the clinker particles, causing changes in the formation of ettringite during the initial hydration, and are therefore a crucial part of the setting process itself. Here, the initial hydration of cement influenced by the interaction of SP and SA was monitored in situ by synchrotron X-ray diffraction. The high time resolution of the measurements allowed a continuous detection of the hydrates formed. The hydration was followed from the starting point of water addition and for couple of hours afterwards. The hydration of the levitated cement pellets containing starch as SA was initialized by adding aqueous solutions of different commercial SPs. Changes in the ettringite formation were detected in comparison to the reference hydration of pure cement. KW - Synchrotron KW - Portland cement Initial hydration KW - Superplasticizer KW - Stabilizer KW - XRD PY - 2016 DO - https://doi.org/http://dx.doi.org/10.1016/j.conbuildmat.2015.12.097 IS - 106 SP - 18 EP - 26 PB - Elsevier AN - OPUS4-35467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram T1 - Wirkungsweise verschiedener Fließmittel N2 - In den vergangenen Jahrzehnten hat sich die Betonbauweise beträchtlich von einer Massenanwendung hin zu einer innovativeren, zukunfts- und leistungsorientierten Werkstofftechnologie weiterentwickelt. Heutzutage besteht Beton nicht mehr länger nur aus Zement, Wasser und Gesteinskörnungen, sondern kann unter Anwendung von Zusatzstoffen und chemischen Zusatzmitteln erheblich verbessert werden. Gleichzeitig beschränken die Betonspezifikationen sich nicht mehr auf den Elastizitätsmodul und Druckfestigkeit, sondern Beton kann ebenfalls zur Erfüllung zahlreicher Anwendungskriterien wie Dauerhaftigkeit, Verarbeitbarkeit, Ästhetik, Brandverhalten und vieler anderer mehr beitragen. Gleichzeitig ist jedoch die Zusammensetzung von Beton wegen der Vielzahl an interagierenden Mischungskomponenten komplizierter geworden. Das Verständnis der Auswirkungen der veränderten Mischungskomponenten ist eine Herausforderung, aber auch der Schlüssel zu einer innovativen Betontechnologie. PY - 2015 SN - 1439-7706 VL - 3 SP - 2 EP - 6 PB - ad-media-Verl. CY - Köln AN - OPUS4-33727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram T1 - Mode of action of different superplasticisers N2 - Over the course of the last decades, concrete construction has significantly changed from mass application towards sophisticated more innovative, future oriented, and performance based materials technology. Today concrete no longer consists of cement, water, and aggregates, but can be enhanced significantly by using supplementary additions and chemical admixtures. At the same time the concrete specifications are no longer limited to Young’s modulus and compressive strength, but concrete may need to be designed for a multiple of application criteria such as durability, workability, optics, fire behaviour, and many more. However at the same time, the composition of concrete has become more complex due to the higher number of mutually interacting mixture constituents. Understanding the effects of changed mixture constituents is challenging but a good understanding is the key to innovative concrete technology. PY - 2015 SN - 1437-9023 IS - 3 SP - 2 EP - 6 PB - ad-media-Verl. CY - Köln AN - OPUS4-33581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -