TY - JOUR A1 - Lorenzoni, Renata A1 - Mezhov, Alexander A1 - Fritsch, Tobias A1 - Schmidt, Wolfram A1 - Kruschwitz, Sabine T1 - Effect of Biochar on the Microstructure and Mechanical Response of Cement Paste N2 - The use of biochar as a supplementary cementitious material is proposed to reduce the global greenhouse gas emissions. Since biochar is non-reactive, has a low density and complex porosity, its incorporation into cementitious materials results in microstructural changes and consequently affects the mechanical response. This work advances the mechanical response understanding of Portland cement composites with 0, 5, and 25 volume percent (vol%) of cement replaced with biochar by using in-situ computed tomography, correlating with the microstructural changes analyzed by HFC, gas sorption, MIP, gas sorption, and NMR. The results highlight the influence of the mesoscale structure on mechanical responses and relate the lack of loss of mechanical strength at 5 vol% replacement to the compensation of decreasing larger pores with biochar addition. At 25 vol% replacement, the amount of weakened zones in the paste due to biochar overcompensates the positive effect of the reduction in larger pores, resulting in a loss of mechanical properties. Hence, small amounts of biochar can enhance the microstructure, but the reduction of the carbon footprint is limited. T2 - 24th International Conference on Composite Materials (ICCM24) CY - Baltimore, Maryland, USA DA - 04.08.2024 KW - Supplementary cementitious materials KW - Biochar KW - Microstructure KW - In-situ computed tomography KW - Mechanical proprieties. PY - 2024 DO - https://doi.org/10.14359/51742027 VL - 362 SP - 1020 EP - 1032 PB - International Concrete Abstracts Portal AN - OPUS4-62115 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robens-Radermacher, Annika A1 - Unger, Jörg F. A1 - Mezhov, Alexander A1 - Schmidt, Wolfram ED - Biondini, F. ED - Frangopo, D. M. T1 - Temperature dependent modelling approach for early age behavior of printable mortars N2 - Structural build-up describes the stability and early-age strength development of fresh mortar used in 3D printing. lt is influenced by several factors, i.e. the composition of the print­ able material, the printing regime, and the ambient conditions. The existing modelling approaches for structural build-up usually define the model parameters for a specific material composition with­ out considering the influence of the ambient conditions. The goal of this contribution is to explicitly include the temperature dependency in the modelling approach. Temperature changes have signifi­ cant impact on the structural build-up process: an increase of the temperature leads to a faster dissol­ ution of cement phases and accelerates hydration. The proposed extended model includes temperature dependency using the Arrhenius theory. The new model parameters are successfully calibrated based on Viskomat measurement data using Bayesian inference. Furthermore, a higher impact of the temperature in the re-flocculation as in the structuration stage is observed. T2 - The Eighth International Symposium on Life-Cycle Civil Engineering (IALCCE 2023) CY - Milano, Italien DA - 02.07.2023 KW - 3D concrete printing KW - Material characterization KW - Structural build-up KW - Thixotropy KW - Model calibration PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582175 SN - 978-1-003-32302-0 DO - https://doi.org/10.1201/9781003323020-146 SN - 978-1-003-32302-0 VL - 1st Edition SP - 1193 EP - 1200 PB - CRC Press AN - OPUS4-58217 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -