TY - CONF A1 - Komann, Steffen A1 - Ballheimer, Viktor A1 - Quercetti, Thomas A1 - Scheidemann, Robert A1 - Wille, Frank T1 - Mechanical and thermal assessment by BAM of a new package design for the transport of SNF from a german research reactor N2 - For disposal of the research reactor of the Technical University Munich FRM II a new transport and storage cask design was under approval assessment by the German authorities on the basis of International Atomic Energy Agency (IAEA) requirements. The cask body is made of ductile cast iron and closed by two bolted lid systems with metal seals. The material of the lids is stainless steel. On each end of the cask the wood-filled impact limiters are installed to reduce impact loads to the cask under drop test conditions. In the cavity of the cask a basket for five spent fuel elements is arranged. This design has been assessed by the Bundesanstalt für Materialforschung und -prüfung (BAM) in view to the mechanical and thermal safety analyses, the activity release approaches, and subjects of quality assurance and surveillance for manufacturing and operation of the package. For the mechanical safety analyses of the package a combination of experimental testing and analytical/numerical calculations were applied. In total, four drop tests were carried out at the BAM large drop test facility. Two tests were carried out as a full IAEA drop test sequence consisting of a 9m drop test onto an unyielding target and a 1m puncture bar drop test. The other two drop tests were performed as single 9m drop tests and completed by additional analyses for considering the effects of an IAEA drop test sequence. The main objectives of the drop tests were the investigation of the integrity of the package and its safety against release of radioactive material as well as the test of the fastening system of the impact limiters. Furthermore, the acceleration and strain signals measured during the tests were used for the verification of finite-element (FE) models applied in the safety analysis of the package design. T2 - Pressure Vessels & Piping Conference 2020 CY - Online meeting DA - 03.08.2020 KW - Mechanik KW - radioaktives Material KW - Transportbehälter KW - Antragsverfahren KW - Zulassungen KW - Typ-B Versandstück KW - Thermik PY - 2020 VL - 2020 SP - 1 EP - 7 PB - ASME CY - New York AN - OPUS4-51103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehrig, Marko A1 - Scheidemann, Robert A1 - Wille, Frank A1 - Ballheimer, Viktor T1 - Investigation of the internal impact during a 9 m drop test of an accident-safe waste package N2 - The safety assessment of packages for the transport of radioactive material follows the IAEA regulations and guidance. The specified regulatory tests cover severe accidents and demonstrate the package containment system integrity. Special attention must be drawn to the behaviour of the content which could move inside the package due to unpreventable gaps caused by the loading procedure and the structure of the content. A possible internal impact of the content which occurs during the drop tests onto the lid system is investigated. The IAEA regulations SSR-6 and the Guidance SSG-26, revised recently, consider input from Germany and France related to the significance of internal gaps. In the context of a waste package design assessment, a model was equipped with a representative content to conduct a drop test with an internal impact. The weight and kinetic impact of this content covered all possible real contents. The objective of the test was to maximize the load onto the lid system and to prove the mechanical integrity by complying with the required leak tightness. The test was conducted conservatively at a package temperature lower than -40 °C at the BAM Test Site Technical Safety. This paper gives an overview of efforts to address internal gaps and their consequences, and the BAM efforts with the implementation of this topic into IAEA regulations and guidance material. The paper then focuses on the conduction of a drop test and investigation of internal component impact. T2 - ASME 2021 Pressure Vessels & Piping Conference (PVP2021) CY - Online meeting DA - 13.07.2021 KW - Internal gaps KW - Drop test KW - IAEA PY - 2021 SN - 978-0-7918-8535-2 DO - https://doi.org/10.1115/PVP2021-60996 SP - 1 EP - 6 PB - American Society of Mechanical Engineers (ASME) CY - New York, NY, USA AN - OPUS4-54742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars A1 - Scheidemann, Robert A1 - Neumeyer, Tino A1 - Komann, Steffen A1 - Wille, Frank T1 - Tightness Verification Procedures of Welded Lids for Encapsulations for Damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Cask (DPC) N2 - Damaged spent nuclear fuel (DSNF) can be loaded in Germany in dual-purpose casks (DPC) for transport and interim storage. Therefore, special encapsulations are needed to guarantee a safe handling and a reliable tight closure. These encapsulations must be durable and leak-tight for a possible long interim storage term and the transport thereafter. Because components inside the package containment like these special encapsulations are not accessible within periodical inspections of the DPC. Due to the general design of DPCs for standard fuel assemblies, specific requirements needed to be considered for the design of the special encapsulations for DSNF to ensure the loading in existing package designs. Especially the content of the encapsulations with damaged spent nuclear fuel must be avoided to enter in the inner space of the DPC, due to the possible higher amount of corrosive and radioactive material as well as greater quantities of water, which can be trapped in defect fuel rods. The main difference of the encapsulations for damaged spent nuclear fuel is that they have no replaceable sealing as tightness barrier. They have a specific welded lid. Therefor the tightness needs to be shown in the design approval process for all transport conditions especially for accident conditions, where high internal impact loads can occur. As German competent authority, BAM is responsible for the safety assessment of the mechanical and thermal design, the release of radioactive material and the quality assurance aspects of manufacturing and operation. Concerning the mechanical package design BAM carried out a comprehensive safety assessment for the specific encapsulations during the package design approval process of the commonly used DPC. For the proof of tightness of the welded lid no representative standards are available. For minor loads the German KTA standards can verify the tightness of a weld seam but only for low stresses. For higher impact loads physical tests are required. These tests were performed with representative drop tests and highly sensitive leak tests. The present paper gives an overview of the applied assessments by BAM and points out the main findings of the mechanical design for the welded sealing. Both verification procedures are described, on one hand with German standards for lower loads and on the other hand with physical tests for higher impact loads. The drop tests based on complex numerical pre-calculations by the applicant which result in optimized dimensions and properties of the test specimens and representative drop heights for the drop tests. The horizontal drop orientation with a plane-parallel impact on the unyielding basement was most challenging and led to specific adaptations during preparation and conduction of the drop tests performed by BAM. With leak tests and the corresponding test evaluation, it could be finally approved that the specific welded sealing of an encapsulations for DSNF is tight for all transport conditions. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Tightness verification KW - Weld seams KW - Drop tests KW - Encapsulations for damaged spent nuclear fuel KW - Helium leak tests PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 10 CY - New York AN - OPUS4-61351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -